Advance Security T30 Car Alarm Transmitter User Manual TX225A Manual
Advance Security Inc Car Alarm Transmitter TX225A Manual
Users Manual
JULY/04/2005 MODEL TX225A REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM 6 Pin White Black Antenna Wire 2 Pin Blue Valet Switch 6 Pin White Mini Connector LED Indicator 2 Pin White 2 Pin White 5 Pin White Blue Wire: (-) 200mA Unlock Pulse Green Wire: (-) 200mA Lock Pulse Main 5 Pin White harness MAIN 5 PIN WIRE HARNESS: 1. Red / White Wire: Parking Light Relay Power Input 2. White Wire: Parking Light Relay Output 3. Black Wire: Ground to Vehicle FRAME 4. Brown Wire: Positive output To Siren 15A Fuse 5. Red Wire: +12V To Constant Battery Source 6 PIN MINI CONNECTOR WIRE HARNESS: 12V 1. Violet Wire: Positive Door Pin Switch Input 2. Blue Wire: Instant Trigger Ground Input 3. Green Wire: Negative Door Pin Switch Input 12V 4. Yellow Wire: To Ignition Switched + 12V Cut From ignition switch 5. Orange Wire: 200mA Grounded when armed 6. Gray Wire: (-) 200mA Programmable Output Red wire 30 White wire Yellow wire 85 Channel 3 / 2 Step Door Unlock. To start solenoid 87a 86 Orange wire A. PROGRAMMING TRANSMITTER: Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is exceeded, the security system will start deleting transmitters from memory in chronological order. 1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds. ALA225 JULY/04/2005 2. Push the Valet switch 3 times and holding in on 3rd push until a long chirp is hearing then release the valet switch. You are now in the Transmitter programming mode. 3. Press and hold any button of the transmitter until the siren responds with a confirming chirp, indicating the signal has been stored into memory. 4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each transmitter. Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. Three long chirps & Three parking light flashes to confirm exit. B. ALARM FEATURES PROGRAMMING: ALARM FEATURE “I” PRORAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. nd 2. Push the Valet switch 2 times and holding in on 2 push until one chirp with a long chirp is hearing then release the valet switch. You are now in the Alarm feature ‘I’ programming mode. 3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to change. a. The siren chirps and LED pause will indicate newly setting. b. The system would advance to [2] LED flash, [2] chirp. (The factory default setting is always [1] LED flash, [1] chirp.) 4. Depress the transmitter button ‘A’ again to change the feature again. Simple keep re-depressing the transmitter button ‘A’ again until the module advances to your desired setting. 5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you want to program. Press One Chirp / Two Chirps / Transmitter LED one pulse LED two pulse Button Factory Default Setting Chirps on Chirps off Automatic Rearm On Automatic Rearm Off Instantly Door Ajar Warning. 45 seconds Delay Door Ajar error chirp. Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. Three long chirps to confirm exit. ALARM FEATURE “II” PRORAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. th 2. Push the Valet switch 4 times and holding in on the 4 push until two chirps with a long chirp is hearing then release the valet switch. You are now in the Alarm feature ‘II’ programming mode. 3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program. Press One Chirp / Two Chirps / Three Chirps / Transmitter LED one pulse LED two pulse LED three pulse Button Factory Default Setting 0.9-second Door lock pulses. 3.0-second Door lock pulse. Double pulse unlock Active arming Passive arming without Passive arming with passive passive door locking door locking. Ignition controlled door locks Without ignition controlled & unlocks door locks & unlocks Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. Three long chirps to confirm exit. ALARM FEATURE “III” PRORAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. th 2. Push the Valet switch 6 times and holding in on the 6 push until three chirps with a long chirp is hearing then release the valet switch. You are now in the Alarm feature ‘III’ programming mode. 3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program. Press One Chirp / Two Chirps / Transmitter LED one pulse LED two pulse Button Factory Default Setting Shock Sensor Program Mode Gray Wire = Trunk (Channel 3) Output Gray Wire = Two Step Door Unlock Output Car Jacking Off Car Jacking On Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. Three long chirps to confirm exit. ADJEST AND TEST THE SENSITIVITY LEVEL OF THE SHOCK SENSOR 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. ALA225 JULY/04/2005 2. Push the Valet switch 6 times and holding in on the 6th push until three chirps with a long chirp is hearing then release the valet switch. You are now in the Alarm feature ‘Shock Sensor’ programming mode. button for 2 seconds. One long siren chirp to indicates the unit is ready to accept 3. Press and hold adjustments of the shock sensor. 4. Press button on the transmitter once will decrease sensitivity level by one, each time an decrease is made the siren chirp will respond with [1] chirp, while 2 chirp indicates the minimum of sensitivity. 5. Press button on the transmitter once will increase sensitivity level by one, each time an increase is made the siren/horn chirp will respond with [1] chirp, while 2 chirp indicates the maximum of sensitivity. 6. Hit the bumper or strong metal part of the vehicle to test the threshold level of the sensor. a). Activate the warn-away (first stage the shock sensor), the siren will emit a short chirp. b). Activate the full alarm (second stage the shock sensor), the siren will emit a long chirp. and buttons at the same time. One long siren chirp to 7. When you are satisfied with the setting, press indicates the unit is lock in the adjustment. Note: If 20 seconds of inactivity expire, or turn on the ignition during of above steps, the unit will exit the program mode and return to the disarmed mode. Three long chirps to confirm exit. OPERATION MANUAL TRANSMITTER OPERATION: Transmitter Button System Function Arm & Lock door Remark Arm & Delete The Shock Sensor Press twice within 3 seconds. (3 seconds) Car Locator Panic function Disarm & Unlock Door Upon Armed. Press and hold for 3 seconds Disarm &Two Steps Door Unlock Press twice within 3 seconds. (2 seconds) Disarm & Pop Trunk Release Silent Arm / Disarm Activate Car-Jacking Press and Hold for 2 seconds Upon Ignition off Upon Ignition on (2 seconds) LED INDICATORS: LED Off Slow flash Fast flash On (solid) Function Disarmed Armed Passive arming Valet mode CHIRP INDICATORS: Chirp 1 chirp 2 chirps 3 chirps 4 chirps 6 chirps Function Arm Disarm Ajar Warning Disarm / Intrusion Car Locator LED 2 flashes... pause 3 flashes... pause 4 flashes... pause 5 flashes... pause Function Trigger on trunk/hood Trigger on door switch Trigger on Dual Zone Shock Sensor Trigger on Ignition switch PARKING LIGHT: Parking light 1 flash 2 flashes 3 flashes 12 flashes Function Arm Disarm Disarm / Intrusion Car Locator ACTIVE ARMING – LOCK & ARM: 1. Press button on transmitter. 2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle doors will lock upon arming when interfaced with the security system. Ajar Warning: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. and buttons at same time will arm or disarm your security Silent Arming / Disarming: Press the system, No chirp sound will be heard, arm / disarm confirmation will be through the vehicles parking lights only. button twice within 3 seconds will arm the security system, by-pass Shock Sensor By-Pass: Press the the shock sensor. The system will chirp one additional time to confirm the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one arming cycle only. The security system will return to normal operation during the next arming cycle. PASSIVE ARMING: ALA225 JULY/04/2005 Active arming / disarming is controlling your security system via the remote transmitter. This security system is equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows. 1. Turn the ignition to the “OFF” position and exit the vehicle. 2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once the vehicle all entrances are closed. 3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren will chirp [1] time and the parking lights will flash [1] time. PASSIVE DOOR LOCKING: The vehicle doors will automatically lock after passive arming cycle has been completed. ACTIVE DISARMING – UNLOCK & DISARM: 1. Press button on the transmitter. 2. The siren will chirp twice and parking light will flash twice to indicating that the security system is now disarmed. The vehicle doors will unlock disarming when interfaced with the security system. Tamper Disarm: If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3 times. Two Step Door Unlock: This feature will independently unlock the drives door only when disarming the button on the transmitter a second time within 3 seconds will unlock the security system. Pushing the entire vehicle. Automatic Re-Arm: If this feature is selected, the security system will automatically re-arm itself 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed. DISARMING WITHOUT A TRANSMITTER The Override function may be used if the remote transmitter is lost or inoperative. 1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.) 2. Within 10 seconds push and release the valet switch The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle normally. VALET MODE: The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm function is bypassed, however the remote panic feature and remote door locks will remain operational. Enter Valet Mode: 1. Turn the ignition to “ON” position. 2. Push and hold valet switch for 2 seconds until the LED turns on. The LED wills remain on as long as the system is in 'valet mode'. Exit Valet Mode: 1. Return to normal operation, turn ignition 'ON'. 2. Push and hold valet switch for 2 seconds, The LED wills turns off indicate the system are exiting the valet mode. PANIC FUNCTION: The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency. button on the transmitter for 3 seconds. The alarm will immediately sound. 1. Press and hold 2. To stop the alarming press and hold button on the transmitter for 3 seconds. 3. If the button is not pressed, the alarm will automatically stop after 30 seconds. TRIGGER THE SYSTEM When armed, your vehicle is protected as follows: 1. Light impacts will trigger the warn-away signal. A long chirp from siren/horn. 2. Heavy impacts / Doors open / Hood open / Trunk open / Turns on the ignition switch will trigger the programmed sequence. The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren and parking lights will turn on to alerting of an intrusion for 30 seconds. Then it will stop and automatic reset and re-arm. If the one of sensors or detectors still active, the alarm system will sound a maximum of 6 times of 30 seconds cycles. ANTI CAR - JACKING Warning: If you don't need the car jacking function in this alarm system, be sure to set car jacking feature “OFF”. This system is default setting car jacking “OFF”. Active Anti Car Jacking: 1. Upon ignition is “On”, press and hold the transmitter and buttons at the same time for 2 seconds. The parking lights will turns on for 1.5 seconds to indicate the system enters the car-jacking mode. 2. Once the system in car-jacking mode, If you are forced from the vehicle, the system will be trigger when the door is opened and closed while the ignition is “ON”. Trigger The Car Jack Mode: ALA225 JULY/04/2005 a). 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds. b). During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off the car-jacking feature. If not, it will enter second timer car jacking. c). 65 seconds after the system has beer triggered. The siren starts alarming and the parking light starts flashing. d). 90 seconds after the system has beer triggered 1. The siren still alarming and the parking light flashing, and 2. The starter disable will activate to prevent the vehicle from starting. 3. It will remain active until the vehicle's battery power exhausted. Override The System To Turn Off Car Jacking: Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and the system disarmed CAR LOCATOR: Upon armed, press button on the transmitter to active car locator function. The siren will chirp 6 times. The parking light will flash 12 times, for you to easily locate your car. TRUNK RELEASE.. Press and hold devices. button on transmitter for two seconds to remote control the trunk release or other electric This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Per FCC 15.21, you are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. ALA225
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2005:09:09 11:34:48+08:00 Modify Date : 2005:09:09 11:34:48+08:00 Page Count : 5 Creation Date : 2005:09:09 03:34:48Z Mod Date : 2005:09:09 03:34:48Z Producer : Acrobat Distiller 5.0 (Windows) Author : feva Metadata Date : 2005:09:09 03:34:48Z Creator : feva Title : Microsoft Word - TX225A Manual.docEXIF Metadata provided by EXIF.tools