Advance Security T69 TX901A User Manual

Download:
Mirror Download [FCC.gov]
Document ID	4047638
Application ID	upDFweCdRwO2XFmIDYGLhg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	69.65kB (870685 bits)
Date Submitted	2018-10-24 00:00:00
Date Available	2018-10-24 00:00:00
Creation Date	2018-04-25 10:40:27
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-10-24 15:35:18
Document Title	Users Manual
Document Creator	Adobe InDesign CC 13.1 (Windows)

Remote Start / Power Harness (6-Pin)
Replacement Part
# 4120110
Notification Harness (4-Pin)
Replacement Part
#4120145
Programming Note:
PINK
RED
PINK/WHITE
ORANGE
RED/WHITE
PURPLE
IGNITION 1 ( + )
BATTERY 12V ( + )
IGNITION 2 ( + ) P
ACCESSORY 1 ( + ) P
BATTERY 12V ( + )
STARTER OUTPUT - MOTOR SIDE ( + )
WHITE/RED
WHITE
BLACK
BROWN
PARKING LIGHT INPUT
PARKING LIGHT OUTPUT
GROUND
SIREN OUTPUT ( + )
** RF KITS SOLD SEPERATELY **
ANTENNA
LED
VALET
ANTENNA PORT
CRS
CAS
Replacement Parts
1-Way
# 4180065
2-Way
# 4180064
Harness (4-Pin) # 4120388
SHOCK SENSOR PORT
Replacement Part
#4120389
Replacement Part
# 4360698
Input / Output
Harness (22-Pin)
BLUE/BLACK
PURPLE/WHITE
GRAY/RED
GREEN
BLUE/WHITE
WHITE/BLUE
PURPLE
BROWN/RED
GRAY
PINK/BLACK
GRAY/BLACK
ORANGE
VIOLET/BLACK
RED/WHITE
BROWN/BLACK
LT GREEN/BLACK
LT BLUE
GREEN/WHITE
BLACK/YELLOW
BLUE/GREEN
ORANGE/BLACK
WHITE/BLACK
User Selectable LED
The unit will not operate unless tach is programmed or a tachless option is
turned ON.  If an attempt is made to start the vehicle via the remote start without first
programming tach, the unit will flash the parking lights 7 times indicating tach has not
been learned and stored.  If the tach rate is not properly programmed to the specific
vehicle, the unit may not realize that the vehicle is running in certain instances and
re-engage the starter motor.
This feature will control whether the LED is ON or OFF when the system is Armed/
Locked. This will be selectable in feature programming OR on-the-fly without entering
the programming feature banks.
The Remote Start unit will learn the tach rate of most vehicle’s single coil, multiple coil
packs, or single injector. To learn tach:
FLCART HARNESS PORT
The default wire function settings are listed next
to the wire color. Wires shown with P can be
programmed to perform different functions.
Refer to the Feature Programming section to
change the default setting.
Tach Programming
START STATUS / ACTIVE OUTPUT ( - )
TACH INPUT
PARKING BRAKE INPUT ( - )
DOOR TRIGGER INPUT ( - )
INSTANT TRIGGER INPUT ( - )
EXTERNAL START INPUT ( - )
DOOR TRIGGER INPUT ( + )
BRAKE INPUT ( + )
HOOD INPUT ( - )
AUX 5 OUTPUT ( - ) P
AUX 3 OUTPUT ( - ) P
GROUND WHEN ARMED ( - ) P
AUX 1 OUTPUT ( - ) P
TRUNK RELEASE OUTPUT ( - ) P
HORN OUTPUT ( - )
FACTORY DISARM / PULSE BEFORE START ( - )
FACTORY ARM / PULSE AFTER START ( - ) P
PULSE AFTER SHUTDOWN ( - ) P
PULSE DURING CRANK ( - ) P
FACTORY DISARM 2 / 2ND UNLOCK ( - ) P
AUX 4 OUTPUT ( - ) P
AUX 2 OUTPUT ( - ) P
1.
Turn the ignition key to the ON position.
2.
Press and release the valet/override button 3 times.
3.
Immediately turn the ignition key OFF.
4.
Press and hold the valet/override button, then start the vehicle using
the key.
5.
When the unit senses the tach signal, the parking lights will begin to
flash.
6.
Allow the vehicle to settle to a normal idle speed.
7.
NOTE: If the unit fails to learn tach rate due to an improper tach connection or a
poor tach source, the parking lights will not flash. To correct this situation, locate and
connect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach
learn routine.
Smart Tachless Mode
Smart Tachless Mode is available only if a tach signal has never been learned to the
system and when activated will automatically change the Tach Mode feature in option
programming to Tachless without the need to enter the feature programming mode.
1.
2.
FLCART PORT
Door Lock Harness (3-Pin)
Replacement Part #1031423
BLUE
OPEN
GREEN
UNLOCK ( - )
LOCK ( - )
86
30
85
ORANGE
RED
BLACK
WHITE / BLACK
OPEN
Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.
Dome Light Delay / Theater Dimming
The system can be programed to delay arming after the lock button is pressed
(60 second max) for vehicles with a dome light delay or theater dimming feature.
Once programed the system will ‘learn’ the timing of the dome light delay and add 2
seconds before arming.
1.
Close all doors with ignition off.
2.
Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK ,
UNLOCK, LOCK. The LED will light solid to indicate the system has
entered DOME DELAY LEARN MODE.
3.
Immediately OPEN then CLOSE the door WITHOUT disarming the
system. The system will then monitor the door trigger wire. Once the
dome light turns off, the system will then add 2 seconds and then exit
the learning mode.
4.
The LED will begin to flash indicating the system has exited the
learning mode and is now armed.
Defaulting the Dome Light Delay: Turn the ignition ON then OFF 3 times then
press and hold the valet button for 5 seconds, the system will chirp 1 time indicating
the learned delay time has been cleared.
Activate the remote start. The parking lights should begin flashing 7
times indicating no tach signal has been learned.
Within the 7 flash time period, press and hold the
button.
Adjusting the Shock Sensor
FLCART PROGRAMMING PORT
87
Turn the ignition ON, OFF, ON, OFF.
DBI PORT
87a
1.
2.
3.
The system will chirp 1 time indicating the system is now in tachless
		mode.
TELEMATICS PORT
STARTER INTERUPT RELAY & HARNESS
Replacement Part #1024405
Release the valet/program push-button switch. The parking lights will
turn on for 2 seconds and 1 long chip will indicate that the learned
tach signal is stored and the unit has exited tach learn mode.
SHOCK SENSOR & HARNESS
Replacement Part #4700023
86 - ARMED OUTPUT ( - )
85 - IGNITION ( + )
87A - STARTER OUTPUT - MOTOR SIDE
30 - STARTER INPUT - KEY SIDE
87 - OPEN
RED
BLACK
BLUE
GREEN
BATTERY 12V ( + )
GROUND WHEN ARMED ( - )
FULL TRIGGER ( - )
WARN AWAY TRIGGER ( - )
1.
Increase sensitivity by turning the adjustment dial clockwise.
2.
Decrease sensitivity by turning the adjustment dial counter clockwise.
PROFESSIONAL
SERIES
Chirp Delete - User Accessible
Security and Remote Start
Installation Quick Reference
Guide
System ARM/DISARM chirps can be toggled ON or OFF without entering the
programming feature banks.
1.
2.
Turn the ignition ON then OFF.
Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.
caSECRS
Security Trigger Zones
Remote Start Shutdown Diagnostics
If the remote start shuts down or fails to start, the parking lights will flash one of the patterns below indicating the shutdown input.
To manually enter diagnostics and view the last shutdown, turn the ignition ON and press and release the
PARKING LIGHT FLASHES		
SHUTDOWN ZONE
3 Flashes					
Hood / Brake Input
4 Flashes					
Remote Start Valet Mode
5 Flashes					
Manual Transmission Mode not ready
7 Flashes					
Tach not learned / Crank Average not learned
button.
If the security system has been triggered the LED will flash one of the patterns below
indicating the zone.
LED FLASHES		
TRIGGER ZONE
2 Flashes				
Hood / Trunk Input
3 Flashes				
Door Input
4 Flashes				
Shock Sensor
5 Flashes				
Ignition Input
Complete guides also available at
www.voxxuniversity.com
2017
Vo x x
Electronics
Corporation.
All
rights
reserved.
Feature Bank 1 - 3 Chirps
Transmitter Programming
Refer to transmitter programming.
Feature Bank 2 - 4 Chirps
Security Control
1 LED Flash
2 LED Flash
Silent Choice
ON
OFF
3 LED Flash
4 LED Flash
Door Locks
Active
Passive
System Arming
Active
Passive
System Notifications
Siren & Horn
Siren Only
5 Alarm Duration
30 Seconds
60 Seconds
Security
ON
OFF
Anti-Hijack Mode
OFF
ON
Ground While Armed
Orange ( - ) Output
Ground While Ground While
Disarmed
Armed
DBI Port Protocol /
Telematic Port Protocol
ADS /
DBI /
ADS /
DBI /
Voxx Telematic Voxx Telematic ADS Telematic ADS Telematic
10 Arm / Disarm Chirps
11 LED Indicator
Standard:
2 - Arm
1 - Disarm
Inverted:
1 - Arm
2 - Disarm
ON
OFF
ON w/ OEM
Remote Start
OFF
Lock Only
Arm & Lock
13 Extended Parking Lights
OFF
After Unlock
After Lock
Standard
Inverted
Parking Light Relay / Trunk ( - )
Output
6 LED Flash
Horn Only
12 Auto Re-lock
14
5 LED Flash
Feature Bank 4 - 6 Chirps
Remote Start Control
1 LED Flash
2 LED Flash
RS Confirmation Chirp
ON
OFF
Run Time
15 Minutes
5 Minutes
Running Lights
Steady
Flashing
Tach Mode
Tach
Tachless
Voltage Level
High
Low
Crank Time
1.0 Seconds
0.8 Seconds
4 LED Flash
5 LED Flash
6 LED Flash
10 Minutes
20 Minutes
45 Minutes
60 Minutes
Transmitter Programming - Feature Bank 1
Hybrid
1.5 Seconds
DBI Port
2.0 Seconds
4.0 Seconds
4 LED Flash
5 LED Flash
6 LED Flash
Lock / Unlock Timing
1 Sec.
3.5 Sec.
1 Sec. Lock,
2x Unlock
30 Sec. Lock,
2x Unlock
2x Lock,
1 Sec. Unlock
0.5 Sec.
Factory Disarm 2
Blue / Green Output
Factory
Disarm
2nd Unlock
Factory Disarm
Factory Disarm Factory Disarm Factory Disarm
w/ Unlock
2x 500mS
350mS
500mS
Timing
Ignition Locks
OFF
Lock / Unlock
Lock Only
Unlock Only
4 Trunk Output Timing
1 Sec.
10 Sec.
20 Sec.
Latched until
IGN ON
Latched ON
until Button
Press
Horn Output Timing
16mS
10mS
30mS
40mS
50mS
Real Panic
ON
OFF
AUX 1
Violet / Black Output
1 Sec.
Latched
Latched until
IGN ON
Dome Light
Output
Defrost Output Defrost Output
Single Pulse
Latched 5 Min
After Start
After Start
AUX 2
White / Black Output
1 Sec.
Latched
Latched until
IGN ON
10 Sec.
w/ Arm
10 Sec.
w/ Disarm
AUX 3
Gray / Black Output
1 Sec.
Latched
Latched until
IGN ON
10 Sec.
w/ Arm
10 Sec.
w/ Disarm
10
AUX 4
Orange / Black Output
1 Sec.
Latched
Latched until
IGN ON
10 Sec.
w/ Arm
10 Sec.
w/ Disarm
11
AUX 5
Pink / Black Output
1 Sec.
Latched
Latched until
IGN ON
10 Sec.
w/ Arm
10 Sec.
w/ Disarm
Within 10 seconds the system will chirp (3) three times.
4.
Press 1 button of each transmitter you wish to program.
5.
The system will respond with 1 chirp for each accepted transmitter.
6.
Pressing the override button at anytime during programming will advance to
the next bank.
Diesel Delay
OFF
10 Sec. Delay
Remote Start Activation
2x Start
1x Start
NOTE: The system will exit transmitter programming after 15 seconds of inactivity.
Ignition
Accessory
NOTE: This system has 1 button programming which programs all channels of the
system.
11 Auto Start Interval
3 Hour
2 Hour
12 Turbo Timer
OFF
1 Minute
13 Transmission Mode
Automatic
Manual
14 Temperature Start
OFF
Accessory Output
15
Orange
16 Pulse Outputs with Unlock
Ignition 2 Output
Pink / White
15 Sec. Delay
20 Sec. Delay
45 Sec. Delay
Start / Crank
NOTE: The system will hold up to 4 transmitters in memory, programming a 5th
transmitter will erase the oldest transmitter in memory.
3 Minute
5 Minute
14F
5F
-4F
Accessory
Ignition
Start / Crank
1.
OFF
IGN, ACCY,
GWR
IGN, ACCY,
GWR - Pulse
After Shutdown
Enter the transmitter into 2 Car Mode. (Refer to transmitter operation in the
owners manual for 2 car operation)
2.
Follow the steps above for transmitter programming.
OFF
Unlock before
Start, Lock
After Start
Unlock Before
Start
NOTE: 2 car mode requires an additional security system installed in a second
vehicle.
NOTE: This system has PTN - Programmed Transmitter Notification. Each time the
ignition is turned ON, the LED will flash the number of transmitters programmed to the
system.
Transmitter programming for 2 Car Mode *2 way LCD system only:
Lock After
Start
Lock After
Shutdown
Manual Feature Programming - Feature Bank 2, 3, 4, & 5
Feature Bank 5 - 7 Chirps
Alternate Output Control
3 LED Flash
Press and hold the valet/override button.
3.
Preset Time
Feature #9 has been updated to DBI Port Protocol & Telematic Port Protocol which
now includes a selection for the telematic port protocol. The new default setting of
DBI / ADS Telematic is the correct protocol setting for the ASCL6 CarLink device.
2 LED Flash
Turn the ignition ON.
2.
Averaging
Feature Bank 2, Programming Update Notice: Firmware version 3.0 or later.
1 LED Flash
1.
Crank Output
17 RS Door Lock Control
Feature Bank 3 - 5 Chirps
Output Control
Set Up & Programming
10
After Lock &
Unlock
3 LED Flash
Factory Disarm
Lt Green / Black Output
1 LED Flash
2 LED Flash
3 LED Flash
Pulse Before
Ground While
Start / During
Running
Unlock
Ignition
4 LED Flash
Accessory
5 LED Flash
Pulse During
Crank
6 LED Flash
1.
Turn the ignition ON.
Pulse Before
Start / During
Unlock - Uses
Unlock Timing
Pulse After
Start / During
Lock - Uses
Lock Timing
2.
Press and hold the valet/override button.
3.
Within 10 seconds the system will chirp (3) three times.
4.
Use the valet/override button to advance through each option bank. For
feature programming advance to Feature Bank 2, 3, 4 or 5, which is (4)
four, (5) five, (6) six and (7) seven chirps.
5.
Use the transmitter
button to scroll through the selections in each
feature bank, the system will chirp to match the feature number.
6.
Press the transmitter
button or the vehicle brake pedal to change the
desired feature. The LED will flash indicating the changed feature.
Factory Arm
Lt Blue Output
Pulse After
Ground While
Start / During
Running
Lock
Ignition
Accessory
Pulse During
Crank
Pulse After Shutdown
Green / White Output
Pulse After
Shutdown
Ground While
Running
Ignition
Accessory
Pulse During
Crank
Pulse After
Shutdown 2
Sec. Delay
Pulse During Crank
Black / Yellow Output
Pulse During
Crank
Ground While
Running
Accessory
Pulse Before
Start / During
Unlock
Pulse Before
Start / During
Unlock - Uses
Unlock Timing
Ignition
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons and
must not be co-located or operating in conjunction with any other antenna or transmitter.
Defaulting All Features: Pressing the
button anytime while in any of the feature
banks will default all features and return you to feature bank 2 - 4 chirps.
NOTE: The system will remain in feature programming mode as long as the ignition is
on, there is no time limit. To exit programming turn the IGNITION OFF.
PC Based Feature Programming / Firmware Updates
When using the NEW Code Alarm Utility App along with a VEPROG Programming tool you may program selectable features or update the firmware of this module. Refer to full
installation guide for additional detail.
1.
To download the Code Alarm Utility App visit the Voxx University website at voxxuniversity.com (registration/login required).
2.
Select VOXXTECH and locate the utility app under the heading Software Downloads.
3.
The Code Alarm Utility App download includes both the CA Utility app and necessary VEPROG drivers.
4.
Install both items before attempting to update modules.
Technical Support (800) 421-3209
or visit
www.voxxuniversity.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2018:04:25 10:40:27-04:00
Creator                         : Adobe InDesign CC 13.1 (Windows)
Modify Date                     : 2018:10:24 15:35:18+08:00
PXC Viewer Info                 : PDF-XChange Viewer;2.5.197.0;Jul  8 2011;20:50:13;D:20181019165814+08'00'
Has XFA                         : No
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2018:10:24 15:35:18+08:00
Creator Tool                    : Adobe InDesign CC 13.1 (Windows)
Instance ID                     : uuid:d3909a31-88e9-4b40-b15e-74171e68321e
Original Document ID            : xmp.did:39FF6623D428E6119A8CBAC6168BE159
Document ID                     : xmp.id:8fb9003e-d645-a844-b0c7-5f0c37b6da38
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:5b921951-a2be-0a40-a2cb-42b6926f2cbc
Derived From Document ID        : xmp.did:505d2c36-c5a0-6f4a-8c3c-94643651f76c
Derived From Original Document ID: xmp.did:39FF6623D428E6119A8CBAC6168BE159
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 13.1 (Windows)
History Changed                 : /
History When                    : 2018:04:25 10:40:27-04:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 2

EXIF Metadata provided by EXIF.tools