Advance Security TR42 Car Alarm Transceiver User Manual one sheet E9 operations
Advance Security Inc Car Alarm Transceiver one sheet E9 operations
Users Manual
CAR LOCATOR
Under armed mode, press the button to active car locator function. The
siren will chirp 6 times. The parking light will flash 12 times, for you to
easily locate your car.
PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger
the alarm in case of emergency.
Press and hold the button for 3 second. The alarm will immediately
sound.
To stop the alarm, press the trunk button on the remote control.
If the button is not pressed, the alarm will automatically stop after 30 seconds.
TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
Light impact will trigger the warn-away signal.
Heavy impacts / Doors open /(if installed) Hood open / (if installed) Trunk
open / Turning on the ignition key will trigger the programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from
cranking. The siren, horn, parking lights, and dome light will turn on alerting
of an intrusion for 30 seconds. Then it will stop and automatic reset and re-
arm. If the any one of the sensors or detectors is still active, the alarm
system will sound a maximum of 3 times of 30 seconds cycles.
NOISE ABATEMENT CIRCUIT: Your system has a “Noise Abatement
Circuit”. It prevents annoying repetitive trigger sequences due to faulty door
pin switches or environmental conditions such as thunder, jackhammers
airport noise, etc.
Here’s how “Noise Abatement Circuit” works: The alarm triggers five times.
Each time, the same sensor or switch has triggered the alarm; the “Noise
Abatement Circuit” will interpret this pattern of triggers as a false alarm.
After the third trigger, the “Noise Abatement Circuit” ignores, or bypasses,
that sensor or switch until a different sensor or switch is trigger.
SYSTEM’S TRIGGER CHECK (For two-way transceiver operation only)
Press and hold F button of LCD remote until 3 beeps sound , release and
re-press F button again, the LCD remote will show “ALARM “ icon flashing
on text area (see advanced users mode), then press button to activate
system trigger check.
SYSTEM’S STATUS CHECK (For two-way transceiver operation only)
Press F button of LCD remote until 3 beeps sound , the LCD remote will
show “STATUS “ icon flashing in the text area (see advanced users
mode), then press button to activate system status check.
It responds with one melody sound and all vehicles’ status records will
immediately displayed on the LCD screen.
Note: If it has no response then you are out of range.
TRUNK RELEASE: Press and hold button on the transmitter for two
seconds to remotely control the trunk release.
CHANNEL 4,5,6 OUTPUTS.
Press the transmitter and buttons at the same time to active Channel
4 function. or
Press and hold F button of LCD remote until 2 beeps sound , release and
re-press F button the LCD remote will show “CH 4” icon flash, then press
button to activate channel 4 function.
Channel 4, 5 & 6 are user-programmable timer outputs. You may program
the built-in timer to send a ground signal for any time duration from 1
second to 120 seconds. For instance, this timer output may be used to turn
on the headlight, power window or sunroof. (Factory defaults setting at
momentary output.)
Press the transmitter and buttons at the same time to active
Channel 5 function. or
Press and hold F button of LCD remote until 2 beeps sound , release and
re-press F button the LCD remote will show “CH 5” icon flash, then press
button to activate channel 5 function.
Press the transmitter and buttons at the same time to active
Channel 6 function. or
Press and hold F button of LCD remote until 2 beeps sound , release and
re-press F button the LCD remote will show “CH 6” icon flash, then press
button to activate channel 6 function.
Clear the Flashing Icon and Melody Sound: The Transmitter will reset the
flashing icons the next time the Ignition is cycled to the ON position.
Stopping The Trigger Melody Sound: When the alarm is triggered, the LCD
screen will alert the user through a melody sound and a flashing trigger icon.
Press any button on the LCD remote transmitter to stop melody sound only.
Remote Start Operation:
WARNINGS:
As with any product that performs automatic functions, there are certain safety
precautions that you must practice and be aware of.
1. Keep the transmitter out of children’s reach.
2. Do not leave anyone in the vehicle while running on remote control.
3. Alert servicing personnel that the vehicle can be started
automatically.
4. Do not start the vehicle by remote while it’s in an enclosed area or
garage.
5. Always apply the parking brake and lock the vehicle as you exit the
vehicle.
6. The vehicle windows must be rolled up.
7. Should the unit malfunction, disconnect the fuse until the problem is
corrected.
8. The use and operations of this system is the sole responsibility of the
operator.
9. Some areas may have local ordinances that prohibit leaving a vehicle
running on public streets.
10.It is not safe to remote start the vehicle if the vehicle is parked on a
steep incline.
TO REMOTE START THE VEHICLE:
When you want to start your vehicle,
1. Press button once on the transmitter.
2. The parking light will activate to indicate the remote start received the
signal.
3. The engine will start in approximately 5 seconds.
4. Once the engine is running, after couple seconds the parking lights will
turn on and the climate controls will activate and adjust the vehicle’s interior
temperature to your preset setting. (While the vehicle is running, the
“minutes” digit on the LCD screen will flash and the will indicate countdown
timer based on the 5, 10, 20 or 30 minute run time set up by your
installation center.)
5. The vehicle will run for a programmable 5 to 30 minute cycle before
shutting down. (When the unit shuts off the countdown timer will turn off
and the transmitter will play a melody.)
NOTE: The Remote Start Unit will not start the vehicle if any one of the
following conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. The optional remote start enable toggle is switched to the “OFF” position.
(If installed)
4. The gear selector is in any gear other then “PARK” or “NEUTRAL”.
SAFE START (Child safety mode)
Factory default is set to press the button once on the transmitter to start
the vehicle. You can program this feature to eliminate an accidental remote
start:
1. The user presses the transmitter buttons twice within 3 seconds to
start the vehicle. or
2. The user presses the transmitter and buttons at the same time to
start the vehicle.
NOTE: Contact your installing dealer to activate this feature.
OPERATE THE VEHICLE WHILE RUNNING FROM THE REMOTE START:
To operate the vehicle while the engine is running from the remote start,
Insert the ignition key and turn it to “ON” (not the start) position.
Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position, the
engine will shut down.
TEMPORARY STOP FEATURE:
This feature allows the vehicle to remain running after the key has been
removed from the ignition. This feature is useful for occasions when you wish
to exit and lock the vehicle for short periods of time, but would like to leave the
motor running and the climate control on.
1. Before turning off the engine, press the button once on the
transmitter and the LED indicator will flash 3 times to confirm enter.
2. Turn the ignition key to OFF position. (The engine will stay running.)
3. The engine will run until the pre-programmed time elapsed or shutdown
input is received.
TURBO CHARGE MODE:
Turbo charger mode keeps the engine running after arriving at your
destination for a programmable period of 1, 3 or 5 minutes, This allows the
vehicle’s engine time to conveniently cool down the turbo after you have
left the vehicle. For use, Please download the complete manual.
TIMER START: Please download the complete manual.
This unit can be programmed to start and run the engine every 3 hours or
punctually at the same time next morning, the engine will run for the
programmed running time and then shut down.
IMPORTANT: Timer Start should be used only in open areas, never
start and run the vehicle in on enclosed space as a garage or carport.
Please be sure you fully understand this feature before use.
TEMPERATURE and VOLTAGE CHECK
Please see advanced user menu below
TO TURN OFF THE REMOTE START:
When the engine is running (by remote start), if you want to stop it,
Press button once on the remote transmitter under the remote start mode.
Press this button twice if the unit is programmed to child safety start.
Press the brake pedal
The vehicle will shut down and turn off the parking light to indicate the
engine has stopped.
SHUT-DOWN INPUT FOR REMOTE STARTER:
If any of the following conditions exist while the system is operating, the
engine will not start or will shut down immediately:
1. The hood is opened.
2. The brake pedal is pressed.
3. The parking (hand) brake is released (For Turbo Timer Mode)
4. Engine is over-revved. {“Tachometer checking type” only}
5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed.
6. Press button on the remote transmitter under remote start mode.
7. The system triggers.
8. The vehicle refused to start running after {3} unsuccessful
attempts.
ADVANCED USER’S MODE:
LCD REMOTE TRANSCEIVER OPERATION:
Enter: Press and hold F Button until beep sound respond from LCD
transceiver indicate into table 1 – 5 as below.
Exit: Press the , or button to exit this mode.
Table 1: ONE beep to confirm (Press & hold “ F “ button until 1 Beep is
heard)
F Button LCD Display Button
Press once Backlight turns on for 5 seconds
Press twice within 5
seconds
PASS and
PASS icon flashing Press button to arm the
alarm and bypass the sensor 1.
Press three times
within 5 seconds
HIDDEN
A
LARM and
icon flashing
Press button to arm system
and with Hidden Alarm Function.
Press four times
within 5 seconds
A
NTI CAR- JAC
K
and
icon flashing
Ignition in "on" position press and
hold button for 2 seconds to
activate anti carjacking functions.
Table 2: TWO beeps to confirm (Press & hold “ F “ button until 2 Beeps
are heard)
F Button LCD display Button
Press and hold the F
Button for 2 second until 2
beeps sounded
MENU flashing Press button to enter the
menu mode
Press one more time within
5 seconds
CH 4 flashing Press button to activate
channel 4 function
Press twice within 5
seconds
CH 5 flashing Press button to activate
channel 5 function
Press three time within 5
seconds
CH 6 flashing Press button to activate
channel 6 function
Table 3: THREE beeps to confirm(Press & hold “F” button until THREE
Beeps are heard)
F Button LCD display Button
Press and hold the F
Button for 3 second
until 3 beeps
sounded
STATUS and
icon is flashing
Press button to check the Vehicle
Status.
Press ONE more
time within 5
seconds
A
LARM and
icon flashing Press button to check the system
trigger condition.
Press TWO more
times within 5
seconds
V
oltage and
Check icon flashing Press button to check the Vehicle
Battery condition.
Press THREE more
times within 5
seconds
TEMP and
icon flashing Press button to check the Interio
Temperature of the vehicle
Press Six more
times within 5
seconds
Start timer and
icon flashing
Press button to activate or cancel
daily start.
Table 4: FOUR beeps to confirm (Press & hold “F” button until 4 beeps
are heard)
F Button LCD display Button
Press and hold the F
Button for 4 second
until 4 beeps sounded
DEMO mode Press button to activate Backlight
will be ON until DEMO operation end.
Table 5: Do-Re-Mi sounds to confirm
F Button LCD
display
Button
Press and hold the F Button for 6
second until Do-Re-Mi sounded
DEFLT
flashing Press & hold button for 2
seconds to back to default setting and
1 chip for confirm
. PROGRAMMING LCD REMOTE (Transmitter Manual mode):
Selecting and Adjusting Menu options:
Press and hold F button for 1 second until 2 beeps sound, then release the F button.
The text will flash on the LCD screen, press button to enter the menu.
Press button to move up in the menu or button to move down in the menu.
Press button to select the option you would like to adjust.
Press button to increase the value, to activate or deactivate a function or to toggle through the
selection.
Press button to decrease the value, to activate or deactivate a function or to toggle
through the selection.
Press button to move to the next sub-option or go back to the main menu.
EXIT: Press button to exit the menu mode.
Trans.
mode
Menu Option LCD displa
y
Functions
1 Parking Menu PARK METER Default is
- Parking hours 0:30
0 is flashing , - Adjusts parking hour
(value from 0 to 2).
- Parking minutes 0:30
30 is flashing
, - Adjusts parking minute
(value from 0 to 59).
- Toggle Parking
countdown + or
- Enables parking countdown.
There is a beep 5 min. before the
Parking countdown reaches 0.
- Disables parking countdown.
2 Illumination Menu Default is
- Toggle Illumination
Mode
3 SEC. or
5 SEC. or
OFF
, Basic operation with backlight
Illumination 3 or 5 sec. or OFF
3 Second Vehicle Default is CAR 1
- Car Select CAR 1 or
CAR 2
-CAR 1 operation.
- CAR 2 operation.
4 Clock Menu Default is
- Clock hours
12:00AM
12 is flashing , - Adjusts clock hour from 0 to
12
- Clock minutes
12:00AM
00 is flashing , - Adjusts clock minute from 0
to 59
5 Alarm Clock Menu Default is
- Alarm hours
12:00AM
12 is flashing , - Adjusts alarm clock hour from
0 to 12
- Alarm minutes 12:00AM
00 is flashing , - Adjusts alarm clock minute
from 0 to 59
- Toggle alarm
ON + or
OFF
- Enable alarm clock or
- Disable alarm clock
6 Confirmation Menu
VIBRATE
Default is
- Toggle Buzzer and
Vibrate
+ or
VIBRATE + or
+ +
, - Buzzer or Vibration
7 Button Lock Menu Default is
- Toggle button lock
- button lock / Disable the
transmitter temporarily
- button unlock / Enable the
transmitter function
8 Power Save Menu Default is
- Toggle power
save
- While the power save mode,
the LCD remote transceiver uses “0”
current to save the battery
power.
- Power save OFF
Exit: Press any button to exit the
“Power Save Mode”.
9 Daily Start Timer Setting
Daily Start Time Adjust Only (ex.
7:30AM)
- Daily Start Hour 7:30AM
7 is flashing , - Adjusts clock hour from 0 to
12
- Daily Start Minute 7:30AM
30 is flashing , - Adjusts clock minute from 0
to 59
To Exit: Do not push any buttons for 15 seconds
TRC760A
QUICK START USERS GUIDE
If you do not understand any part of this quick start users
manual and would like the complete version,
The complete manual is necessary for advanced users and not all user
functions are covered in this quick start guide.
Temperature
Start
Engine will start
automatically
when the
programmed
temperature is
reached
Turbo Timer
Turbo timer was set
up.(programmable)
Manual Gear
Memorizing
condition for
manual gear start.
A
ctivate Channel 3
(Trunk Release).
Activate Channel
5
Activate Channel 4
Time Monitor
Activate Channel 6
Parking Meter
Parking meter
reminder time.
12:00
Alarm Clock
Alarm clock set.
Melody Mode
Remote Control
alerts user through
a melody sound
Low Battery
You have to change
the battery of
remote control.
Valet Mode
Remote start and
alarm functions
temporarily
disabled
Vibration Mode
Remote Control
vibrates when the
system is triggered
Transmitter
Button System Function Remark
Lock Doors & Arm System
Panic function
Press and Hold for 3
seconds. Press Trunk
button to stop panic function
Car Locator Press when in armed mode
- Arm and Delete The 2 Stage
Shock Sensor
Press twice within 3
seconds. Pass will appear on
the remote
- Arm System and Silent Alarm
Function
Press within 3 seconds and
Hold the button
+ Silent Arming / Disarming Ignition in "off" position.
+ Active Anti Car-Jacking Mode Ignition in "on" position press
and hold for 2 seconds
Unlock Doors & Disarm System
- Two Steps Door Unlock &
Disarm System (optional) Press twice within 3 seconds.
Trunk Release (Channel 3) Press and Hold for 2 seconds
- Passive Arming By-pass While the system Disarmed.
Activate or Turn Off The
Remote Start
Press button once or -
Press Twice if set to start
safety mode
+ Channel # 4 Timer Output (4) Optional
+ Channel # 5 Timer Output (5) Optional
+ Channel # 6 Timer Output (6) Optional
+
Switching code For 2nd Car
Operation.
For regular remote
transmitter
ACTIVE ARMING – LOCK & ARM:
1. Press button on the transmitter.
2. The siren will chirp once and parking light will flash once indicating that
the system is now armed. The vehicle’s doors will lock upon arming if
interfaced with the security system.
DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then you
have left a door, trunk, or hood lid ajar.
SILENT ARMING / DISARMING: Press the transmitter and buttons
at the same time. This will arm or disarm your security system, No chirp
sound will be heard, arm / disarm confirmation will be through the vehicles
parking lights only.
SENSOR BY-PASS: Press the button two times within 5 seconds will
arm the security system and by-pass the shock sensor.
HIDDEN ALARM FUNCTION: Silent Alarm
Press the button first; within 3 seconds press the button to activate
the hidden alarm function. The security system will arm and with “Hidden
Alarm Mode” The siren / horn will be silenced even if the sensor is
triggered in the armed mode. Alarm indication will only appear on the LCD
Transmitter.
PASSIVE ARMING (Programmable)
Active arming / disarming is controlled by your security system via the
remote transmitter. This security system is equipped with an optional
Passive Arming feature which allows the security system to arm 30
seconds after the last door is closed. Operation is as follows.
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for
30 seconds. If you reopen any door / hood / trunk, the security system
LED will stop flashing. It will begin flashing again once all vehicle
entrances are closed.
3. After the 30-second time has elapsed, the security system will
automatically “ARM”. The siren will chirp [1] time and the parking lights
will flash [1] time.
PASSIVE ARMING WITH PASSIVE DOOR LOCKING
The vehicle doors will automatically lock after the passive arming cycle
has been completed.
PASSIVE ARMING BY-PASS: While the system is disarmed, Press the
button twice, the system will respond with [1] chirp and LED will turn
“ON”. The security system will remain in this temporary state for as long
as you wish. To exit passive by-pass, press the transmitter or
buttons and the system will return to normal status.
ACTIVE DISARMING – UNLOCK & DISARM:
1. Press button on the transmitter.
2. The siren will chirp twice and the parking lights will flash twice
indicating that the security system is now disarmed. The vehicle’s
doors will unlock.
TAMPER DISARMING: If the alarm is triggered, upon disarm the system’s
siren will chirp 4 times, and the parking lights will flash 3 times telling you
the alarm has been triggered during the last armed state.
PATHWAY ILLUMINATION: When receiving an unlock /disarm signal, this
feature will turn the parking lights “ON” for 30 seconds and for 10 seconds
upon the lock signal. (Programmable)
AUTOMATIC RE-ARM: If this feature is selected, the security system will
automatically re-arm itself in 60 seconds after disarming with remote
transmitter. Automatic rearm will cancel if any door is opened before the 60
seconds timer has elapsed.
DISARMING WITHOUT A TRANSMITTER:
The Override function may be used if the remote transmitter is lost or
inoperative.
1. Enter the vehicle and turn the ignition switch to the 'ON’ position.
2. (Alarm will sound.)
3. Within 10 seconds push and release the valet switch. The alarm will stop
sounding and enter the disarm mode. You can now start and operate the
vehicle normally.
VALET MODE: (System is in Disarm Mode)
The valet switch allows you to temporarily bypass all alarm function,
eliminating the need to hand your transmitter to parking attendants or
garage mechanics. When the system is in valet mode, all alarm functions
and remote start functions are bypassed, however, the remote panic
feature and remote door locks will remain operational. To use the valet
mode, the system must first be disarmed either by using your remote
transmitter, or by operating the Manual Override sequence.
a). Under disarm mode, turn the ignition to “ON” position.
b). Press and hold valet switch for 2 seconds until the LED turns ON
solid. The LED will remain on as long as the system is in 'valet mode'.
Exit Valet Mode:
a). Turn ignition 'ON'.
b). Push and hold valet switch for 2 seconds, The LED will turn off
indicate the system are exiting the valet mode.
Encore E-9 Remote Transceiver
STANDARD LCD ICON CONFIGURATIONS:
The lock icon will be
displayed when
system is ARMED
The unlock icon
will be displayed
when the system is
disarmed.
Sensor Bypass
Shock sensor by-
passed
Hidden Alarm
Mode (silent
Alarm)
Hood Trigger
Hood is illegally
opened (Zone 1)
Trunk Trigger
Trunk is illegally
opened (Zone 2)
Door Open
Warning
Doors are illegally
opened (Zone 3)
Sensor Trigger
Trigger on shock
Sensor 1 (Zone 4)
Ignition Trigger
Ignition switch is
illegally turned on
(Zone 5)
System trigger
Remote
Transmission
You are transmitting
to the control unit.
In – Range
Indicator
You are within the
range of the
remote control.
Anti Car-Jack
Mode Activated
Systems Check
Mode
Engine Cranking
Your vehicle engine
Cranking by remote
control
Engine Running
Your vehicle's
engine is running
Timer Control
Start
Engine will start
automatically every
2 or 3 hours.
Daily Start
Engine will start
automatically at
the same time next
day
BATTERY CHANGING:
Depending on the usage, the remote batteries should be changed at least
once a year in the one way remote and once every 3-8 months for the two-
way remote.
The 1-way remote, (E-9s) is powered by a pair of 3V, CR2016 batteries.
These batteries are available at most locations batteries are sold and can
be replaced by the user.
Battery Level Indicator (2-way remote)
The Battery Level indicator has three level indicators that serve as a visual
indication of battery charge. When the battery reaches a low charge level
that requires changing, the remote control will generate a single notification
chirp, and the Battery Level indicator will flash continuously. If the
battery voltage is LOW, the range of the remote will be reduced by 50% to
conserve battery life. The two way remote requires 2, 3 Volt CR2032
batteries. The operation lives of these batteries are affected by many
factors including, temperature, usage, back-light ON time and
programmable “in range status settings”. Do not allow these batteries to
corrode or become wet for any extended period of time.
REMOTE TRANSMITTER OPERATION:
CHIRP INDICATORS: PARKING LIGHT:
Chirp Function Parking light Function
1 chirp Arm 1 flash Arm
2 chirps Disarm 2 flashes Disarm
3 chirps Defective Reminder 3 flashes Disarm / Triggered
4 chirps Disarm / Triggered 12 flashes Car Locator
6 chirps Car Locator Constant On Under Remote Start
ALARM OPERATING CONDITION:
Siren /
Horn
Parking
Light LED Doors Starter
Dome
Light
1. Arming 1 or 3
Chirps 1 Flash Slow Flash Locking Disable
2. Disarming 2 or 4
Chirps
2 or 3
Flashes Unlocking
Turns on
for 30 -
second
3. Trigger Alarming Flashes Slow Flash Disable Flashes
4. Passive
Starter
Disable
Fast Flash Disable
5. Panic Alarming Flashes Flashes
6. Car-Jacking Alarming Flashes Disable Flashes
7. Car Locator 6 Chirps 12
Flashes Locking
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference
that may cause undesired operation.
Warning!
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.