Advance Security TR74 TRE901AM User Manual

Advance Security Inc TRE901AM Users Manual

Users Manual

Dome Light Delay / Theater Dimming
The system can be programed to delay arming after the lock button is pressed
(60 second max) for vehicles with a dome light delay or theater dimming feature.
Once programed the system will ‘learn’ the timing of the dome light delay and add 2
seconds before arming.
1. Close all doors with ignition off.
2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK ,
UNLOCK, LOCK. The LED will light solid to indicate the system has
entered DOME DELAY LEARN MODE.
3. Immediately OPEN then CLOSE the door WITHOUT disarming the
system. The system will then monitor the door trigger wire. Once the
dome light turns off, the system will then add 2 seconds and then exit
the learning mode.
4. TheLEDwillbegintoashindicatingthesystemhasexitedthe 
learning mode and is now armed.
Defaulting the Dome Light Delay: Turn the ignition ON then OFF 3 times then
press and hold the valet button for 5 seconds, the system will chirp 1 time indicating
the learned delay time has been cleared.
User Selectable LED
This feature will control whether the LED is ON or OFF when the system is Armed/
Locked.ThiswillbeselectableinfeatureprogrammingORon-the-ywithoutentering
the programming feature banks.
1. Turn the ignition ON, OFF, ON, OFF.
2. Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.
PROFESSIONAL
SERIES
Security and Remote Start
Installation Quick Reference
Guide
caSECRS
2017 Voxx Electronics Corporation. All rights reserved.
Adjusting the Shock Sensor
1. Increase sensitivity by turning the adjustment dial clockwise.
2. Decrease sensitivity by turning the adjustment dial counter clockwise.
Tach Programming
The unit will not operate unless tach is programmed or a tachless option is
turned ON.Ifanattemptismadetostartthevehicleviatheremotestartwithoutrst
programmingtach,theunitwillashtheparkinglights7timesindicatingtachhasnot
beenlearnedandstored.Ifthetachrateisnotproperlyprogrammedtothespecic
vehicle, the unit may not realize that the vehicle is running in certain instances and
re-engage the starter motor.
The Remote Start unit will learn the tach rate of most vehicle’s single coil, multiple coil
packs, or single injector. To learn tach:
1. Turn the ignition key to the ON position.
2. Press and release the valet/override button 3 times.
3. Immediately turn the ignition key OFF.
4. Press and hold the valet/override button, then start the vehicle using
the key.
5. When the unit senses the tach signal, the parking lights will begin to
 ash.
6. Allow the vehicle to settle to a normal idle speed.
7. Release the valet/program push-button switch. The parking lights will
turn on for 2 seconds and 1 long chip will indicate that the learned
tach signal is stored and the unit has exited tach learn mode.
NOTE: If the unit fails to learn tach rate due to an improper tach connection or a
poortachsource,theparkinglightswillnotash.Tocorrectthissituation,locateand
connect the PURPLE/WHITE wire to the proper tach signal, and then repeat the tach
learn routine.
Smart Tachless Mode
Smart Tachless Mode is available only if a tach signal has never been learned to the
system and when activated will automatically change the Tach Mode feature in option
programming to Tachless without the need to enter the feature programming mode.
1. Activatetheremotestart.Theparkinglightsshouldbeginashing7
times indicating no tach signal has been learned.
2. Withinthe7ashtimeperiod,pressandholdthe button.
3. The system will chirp 1 time indicating the system is now in tachless
mode.
Chirp Delete - User Accessible
System ARM/DISARM chirps can be toggled ON or OFF without entering the
programming feature banks.
1. Turn the ignition ON then OFF.
2. Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.
RED
BATTERY 12V ( + )
BLACK
GROUND WHEN ARMED ( - )
BLUE FULL TRIGGER ( - )
GREEN WARN AWAY TRIGGER ( - )
SHOCK SENSOR & HARNESS
Replacement Part
#4700023
ORANGE 86 - ARMED OUTPUT ( - )
RED 85 - IGNITION ( + )
BLACK 87A - STARTER OUTPUT - MOTOR SIDE
WHITE / BLACK 30 - STARTER INPUT - KEY SIDE
OPEN 87 - OPEN
STARTER INTERUPT RELAY & HARNESS
86 85
30
87
87a
Replacement Part
#1024405
DBI PORT
SHOCK SENSOR PORT
TELEMATICS PORT
BLUE/BLACK START STATUS / ACTIVE OUTPUT ( - )
PURPLE/WHITE TACH INPUT
GRAY/RED PARKING BRAKE INPUT ( - )
GREEN DOOR TRIGGER INPUT ( - )
BLUE/WHITE INSTANT TRIGGER INPUT ( - )
WHITE/BLUE EXTERNAL START INPUT ( - )
PURPLE DOOR TRIGGER INPUT ( + )
BROWN/RED BRAKE INPUT ( + )
GRAY HOOD INPUT ( - )
PINK/BLACK AUX 5 OUTPUT ( - )
GRAY/BLACK AUX 3 OUTPUT ( - )
ORANGE GROUND WHEN ARMED ( - )
VIOLET/BLACK AUX 1 OUTPUT ( - )
RED/WHITE TRUNK RELEASE OUTPUT ( - )
BROWN/BLACK HORN OUTPUT ( - )
LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - )
LT BLUE FACTORY ARM / PULSE AFTER START ( - )
GREEN/WHITE PULSE AFTER SHUTDOWN ( - )
BLACK/YELLOW PULSE DURING CRANK ( - )
BLUE/GREEN FACTORY DISARM 2 / 2ND UNLOCK ( - )
ORANGE/BLACK AUX 4 OUTPUT ( - )
WHITE/BLACK AUX 2 OUTPUT ( - )
#4120389
WHITE/RED PARKING LIGHT INPUT
WHITE PARKING LIGHT OUTPUT
BLACK GROUND
BROWN SIREN OUTPUT ( + )
#4120145
BLUE UNLOCK ( - )
OPEN
GREEN LOCK ( - )
#1031423
CASECRS
# 4360698
FLCART PROGRAMMING PORT
FLCART PORT
FLCART HARNESS PORT
PINK IGNITION 1 ( + )
RED BATTERY 12V ( + )
PINK/WHITE IGNITION 2 ( + )
ORANGE ACCESSORY 1 ( + )
RED/WHITE BATTERY 12V ( + )
PURPLE STARTER OUTPUT - MOTOR SIDE ( + )
# 4120110
Replacement Part
Replacement Part
Replacement Part
Remote Start / Power Harness
(6-Pin)
Replacement Part
Replacement Part
Notification Harness
(4-Pin)
Input / Output
Harness
(22-Pin)
Door Lock Harness
(3-Pin)
ANTENNA
LED
VALET
** RF KITS SOLD SEPERATELY **
Replacement Parts
1-Way # 4180065
2-Way # 4180064
Harness (4-Pin)
# 4120388
ANTENNA PORT
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
Programming Note:
P
The default wire function settings are listed next
to the wire color. Wires shown with can be
programmed to perform different functions.
Refer to the Feature Programming section to
change the default setting.
P
Security Trigger Zones
IfthesecuritysystemhasbeentriggeredtheLEDwillashoneofthepatternsbelow
indicating the zone.
LED FLASHES TRIGGER ZONE
2 Flashes Hood / Trunk Input
3 Flashes Door Input
4 Flashes Shock Sensor
5 Flashes Ignition Input
Remote Start Shutdown Diagnostics
Iftheremotestartshutsdownorfailstostart,theparkinglightswillashoneofthepatternsbelowindicatingtheshutdowninput.
To manually enter diagnostics and view the last shutdown, turn the ignition ON and press and release the button.
PARKING LIGHT FLASHES SHUTDOWN ZONE
3 Flashes Hood / Brake Input
4 Flashes Remote Start Valet Mode
5 Flashes Manual Transmission Mode not ready
7 Flashes Tach not learned / Crank Average not learned
Complete guides also available at
www.voxxuniversity.com
Defaulting All Features: Pressing the button anytime while in any of the feature
banks will default all features and return you to feature bank 2 - 4 chirps.
NOTE: The system will remain in feature programming mode as long as the ignition is
on, there is no time limit. To exit programming turn the IGNITION OFF.
Manual Feature Programming - Feature Bank 2, 3, 4, & 5
1. Turn the ignition ON.
2. Press and hold the valet/override button.
3. Within 10 seconds the system will chirp (3) three times.
4. Use the valet/override button to advance through each option bank. For
feature programming advance to Feature Bank 2, 3, 4 or 5, which is (4)
four,(5)ve,(6)sixand(7)sevenchirps.
5. Use the transmitter button to scroll through the selections in each
feature bank, the system will chirp to match the feature number.
6. Press the transmitter button or the vehicle brake pedal to change the
desiredfeature.TheLEDwillashindicatingthechangedfeature.
Set Up & Programming
Transmitter Programming - Feature Bank 1
1. Turn the ignition ON.
2. Press and hold the valet/override button.
3. Within 10 seconds the system will chirp (3) three times.
4. Press 1 button of each transmitter you wish to program.
5. The system will respond with 1 chirp for each accepted transmitter.
6. Pressing the override button at anytime during programming will advance to
the next bank.
NOTE: The system will exit transmitter programming after 15 seconds of inactivity.
NOTE: This system has 1 button programming which programs all channels of the
system.
NOTE: The system will hold up to 4 transmitters in memory, programming a 5th
transmitter will erase the oldest transmitter in memory.
NOTE:ThissystemhasPTN-ProgrammedTransmitterNotication.Eachtimethe
ignitionisturnedON,theLEDwillashthenumberoftransmittersprogrammedtothe
system.
Transmitter programming for 2 Car Mode *2 way LCD system only:
1. Enter the transmitter into 2 Car Mode. (Refer to transmitter operation in the
owners manual for 2 car operation)
2. Follow the steps above for transmitter programming.
NOTE: 2 car mode requires an additional security system installed in a second
vehicle.
Refer to transmitter programming.
Feature Ba nk 1 - 3 Chirps
Transm itter Programming
Feature Bank 2 - 4 Chirps
Security Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash
1Silent Choice ON OFF
2Door Locks Active Passive
3System ArmingActive Passive
4System Notifications Siren & Horn Siren Only Horn Only
5Alarm Duration 30 Seconds 60 Seconds
6SecurityON OFFON w/ OEM
Remote Start
7Anti-Hijack Mode OFFON
8Ground While Armed
Orange ( - ) Output
Ground While
Armed
Ground While
Disarmed
9DBI Port Protocol /
Telematic Port Protocol
DBI /
Voxx Telematic
ADS /
Voxx Telematic
DBI /
ADS
Telematic
ADS /
ADS Telematic
10 Arm / Disarm Chirps
Standard:
2 - Arm
1 - Disa rm
Inve rted:
1 - Arm
2 - Disarm
11 LED IndicatorON OFF
12 Auto Re-lock OFFLock Only Arm & Lock
13 Extended Parking Lights OFF After Unlock After Lock After Lock &
Unlock
14 Parking Light Relay / Trunk ( - )
Output Standard Inverted
Feature Bank 3 - 5 Chirps
Output Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash
1Lock / Unlock Timing 1 Sec. 3.5 Sec. 1 Sec. Lock,
2x Unlock
30 Sec. Lock,
2x Unlock
2x Lock,
1 Sec. Unlock 0.5 Sec.
2Factory Disarm 2
Blue / Green Output
Factory
Disa rm 2nd Unlock Factory Disarm
2x 500mS
Factory Disarm
350mS
Factory Disarm
500mS
Factory Disarm
w/ Unlock
Timing
3Ignition Locks OFFLock / Unlock Lock Only Unlock Only
4Trunk Output Timing1 Sec. 10 Sec.20 Sec. Latched until
IGN ON
Latched ON
until Button
Press
5Horn Output Timing16mS 10mS 30mS 40mS 50mS
6Real PanicON OFF
7AUX 1
Violet / Black Output 1 Sec. LatchedLatched until
IGN ON
Dome Light
Output
Defrost Output
Single Pulse
After Start
Defrost Output
Latched 5 Min
After Start
8AUX 2
White / Black Output 1 Sec. LatchedLatched until
IGN ON
10 Sec.
w/ Arm
10 Sec.
w/ Disarm
9AUX 3
Gray / Black Output 1 Sec. LatchedLatched until
IGN ON
10 Sec.
w/ Arm
10 Sec.
w/ Disarm
10 AUX 4
Orange / Black Output 1 Sec. LatchedLatched until
IGN ON
10 Sec.
w/ Arm
10 Sec.
w/ Disarm
11 AUX 5
Pink / Black Output 1 Sec. LatchedLatched until
IGN ON
10 Sec.
w/ Arm
10 Sec.
w/ Disarm
Feature Bank 4 - 6 Chirps
Remote Sta rt Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash
1RS Confirmation Chirp ON OFF
2Run Time 15 Minutes5 Minutes10 Minutes20 Minutes45 Minutes60 Minutes
3Running LightsSteady Flashing
4Tach Mode Tach TachlessHybridDBI Port
5Voltage Level High Low
6Crank Time 1.0 Seconds 0.8 Seconds 1.5 Seconds 2.0 Seconds 4.0 Seconds
7Crank Output Averaging Preset Time
8Diesel DelayOFF 10 Sec. Delay 15 Sec. Delay 20 Sec. Delay 45 Sec. Delay
9Remote Start Activa tion 2x Sta rt 1x Start
10 Ignition 2 Output
Pink / White Ignition Accessory Start / Crank
11 Auto Start Interval3 Hour 2 Hour
12 Turbo TimerOFF1 Minute 3 Minute5 Minute
13 Transmission Mode AutomaticManual
14 Temperature StartOFF14F5F-4F
15 Accessory Output
Orange Accessory Ignition Start / Crank
16 Pulse Outputs with UnlockOFFIGN, ACCY,
GWR
IGN, ACCY,
GWR - Pulse
After Shutdown
17 RS Door Lock ControlOFF
Unlock before
Start, Lock
After Start
Unlock Before
Start
Lock After
Start
Lock After
Shutdown
Feature Ba nk 5 - 7 Chirps
Alternate Output Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash
1Factory Disarm
Lt Green / Black Output
Pulse Before
Start / During
Unlock
Ground While
RunningIgnition Accessory Pulse During
Crank
Pulse Before
Start / During
Unlock - Uses
Unlock Timing
2Factory Arm
Lt Blue Output
Pulse After
Start / During
Lock
Ground While
RunningIgnition Accessory Pulse During
Crank
Pulse After
Start / During
Lock - Uses
Lock Timing
3Pulse After Shutdown
Green / White Output
Pulse After
Shutdown
Ground While
RunningIgnition Accessory Pulse During
Crank
Pulse After
Shutdown 2
Sec. Delay
4Pulse During Crank
Black / Yellow Output
Pulse During
Crank
Ground While
RunningIgnition Accessory
Pulse Before
Start / During
Unlock
Pulse Before
Start / During
Unlock - Uses
Unlock Timing
PC Based Feature Programming / Firmware Updates
WhenusingtheNEWCodeAlarmUtilityAppalongwithaVEPROGProgrammingtoolyoumayprogramselectablefeaturesorupdatethermwareofthismodule.Refertofull
installation guide for additional detail.
1. To download the Code Alarm Utility App visit the Voxx University website at voxxuniversity.com (registration/login required).
2. Select VOXXTECH and locate the utility app under the heading Software Downloads.
3. The Code Alarm Utility App download includes both the CA Utility app and necessary VEPROG drivers.
4. Install both items before attempting to update modules.
Technical Support (800) 421-3209
or visit
www.voxxuniversity.com
Feature Bank 2, Programming Update Notice: Firmware version 3.0 or later.
Feature #9 has been updated to DBI Port Protocol & Telematic Port Protocol which
now includes a selection for the telematic port protocol. The new default setting of
DBI / ADS Telematic is the correct protocol setting for the ASCL6 CarLink device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your
body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons
and must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu