Advantech Co MARS-1030 Portable Data Terminal User Manual Mars 1030 Book

Advantech Co Ltd Portable Data Terminal Mars 1030 Book

MARS 1030 User Manual PDF Download & Text

Manual

Download:
Mirror Download [FCC.gov]
Document ID	722041
Application ID	HnXgFGncFiEjQ99dzmbCKg==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	178.19kB (2227342 bits)
Date Submitted	2006-10-30 00:00:00
Date Available	2006-10-30 00:00:00
Creation Date	2006-09-26 11:28:18
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2006-10-30 10:58:41
Document Title	Mars-1030 Book.book
Document Creator	FrameMaker 7.0
Document Author:	Fandi

MARS-1030
WinCE. NET Rugged Portable
Data Terminal
User Manual
MARS-1030 User Manual
ii
Contents
Chapter 1
Introduction .......................................................1
1.1 About this Manual ........................................................................ 2
1.2 User and Product Safety ............................................................... 3
1.3 Federal Communication Commission Interference Statement ..... 5
1.4 Product Labeling........................................................................... 7
1.5 System Specifications................................................................... 9
1.6 Environment Standard ................................................................ 11
1.7 Warranty and after service ......................................................... 12
Chapter 2
Getting Started .................................................13
2.1 Check the package ...................................................................... 14
2.2 General View of the PDT ........................................................... 15
2.2.1 PDT front side view ............................................................... 15
2.2.2 PDT back side view ................................................................ 15
2.3 Charging the Battery Pack .......................................................... 17
2.3.1 Installing the battery pack ...................................................... 17
2.3.2 Charging the battery pack with Power Adapter ..................... 21
2.3.3 Charging the battery pack with Single Dock .......................... 22
2.4 Handling the PDT ....................................................................... 24
2.4.1
2.4.2
2.4.3
2.4.4
2.4.5
2.4.6
2.4.7
2.4.8
Starting the PDT ..................................................................... 24
Power on / off ......................................................................... 25
Calibration of the touch Screen ...................... 25
Adjusting the brightness ......................................................... 26
To mute the Sound ................................................................. 26
Using the Stylus ...................................................................... 26
Using the Keypad ................................................................... 27
Using the Ear/Microphone ..................................................... 40
2.5 Navigating the Display ............................................................... 41
2.5.1 Setting Time and Date ............................................................ 41
2.5.2 Entering the Data .................................................................... 42
iii
Table of Contents
2.5.3
2.5.4
2.5.5
2.5.6
2.5.7
2.5.8
The Command Bar ................................................................. 42
The Task Bar .......................................................................... 43
The Soft Keypad ..................................................................... 43
Setting Up Wireless LAN RF ................................................. 44
Scanning Barcode ................................................................... 46
Help ........................................................................................ 47
2.6 Power management..................................................................... 48
2.6.1 Suspend Mode ........................................................................ 48
2.6.2 Resuming ................................................................................ 49
2.7 Resetting the PDT....................................................................... 50
2.7.1 Software (Warm) Reset .......................................................... 50
2.7.2 Cold Reset .............................................................................. 50
Chapter 3
Setting................................................................51
3.1 Introduction ................................................................................ 52
3.2 Control Panel .............................................................................. 52
3.2.1 BarCode Setting ..................................................................... 53
3.2.2 Symbologies List .................................................................... 62
3.2.3 Bluetooth Device Properties ................................................... 81
3.2.4 Certificates .............................................................................. 84
3.2.5 Control Center ........................................................................ 86
3.2.6 Date/Time ...................................... 91
3.2.7 Dialing Properties ................................ 91
3.2.8 Display Properties ................................ 93
3.2.9 Input Panel .............................................................................. 95
3.2.10Internet Options ...................................................................... 96
3.2.11Keyboard ................................................................................ 98
3.2.12Network and Dial-up Connections ......................................... 99
3.2.13Owner ................................................................................... 104
3.2.14Password ............................................................................... 105
3.2.15PC Connection ...................................................................... 106
3.2.16Power .................................................................................... 107
3.2.17Regional Settings .................................................................. 109
3.2.18Remove Programs ................................................................ 110
3.2.19Storage Manager ................................................................... 111
3.2.20Stylus .................................................................................... 112
MARS-1030 User Manual
iv
3.2.21System .................................................................................. 114
3.2.22Volume & Sounds Properties ............................................... 116
3.3 Taskbar and Start Menu............................................................ 117
Chapter 4
Communication ..............................................119
4.1 Installing & Setting Up Microsoft ActiveSync ........................ 120
4.1.1 Installing Microsoft ActiveSync on the Host PC ................. 120
4.1.2 Connecting PDT to Host PC ................................................ 120
4.2 Using ActiveSync ..................................................................... 121
4.2.1 Setting up a Partnership ........................................................ 121
4.2.2 ActiveSync File Synchronization ......................................... 122
4.3 Networking ............................................................................... 122
Chapter 5
Software Applications....................................123
5.1 Introduction............................................................................... 124
5.2 Software Applications .............................................................. 124
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.2.6
5.2.7
5.2.8
Calculator ............................................................................. 124
Inbox ..................................................................................... 124
Internet Explorer ................................................................... 134
Media Player ......................................................................... 138
Messenger ............................................................................. 138
Microsoft WordPad .............................................................. 139
Remote Connection .............................................................. 145
Windows Explorer ................................................................ 146
5.3 DiskOnChip ............................................................................. 148
5.3.1 Saving to Flash ..................................................................... 148
5.3.2 DiskOnChip Location ........................................................... 148
5.3.3 DiskOnChip Size .................................................................. 149
Appindex A Barcode Setting ..............................................151
A.1 Setup Tab .................................................................................. 152
A.1.1 Symbology Setup ................................................................. 154
A.1.2 Decoder Setup ...................................................................... 155
A.1.3 Options ................................................................................. 157
Table of Contents
A.2 Update Tab................................................................................ 158
A.3 Symbologies List ...................................................................... 160
A.3.1 Aztec ..................................................................................... 160
A.3.2 Codabar ................................................................................ 161
A.3.3 Code 11 ................................................................................. 162
A.3.4 Code 128 ............................................................................... 163
A.3.5 Code 39 ................................................................................. 164
A.3.6 Code 49 ................................................................................. 166
A.3.7 Code 93 ................................................................................. 167
A.3.8 Composite Codes .................................................................. 168
A.3.9 Data Matrix ........................................................................... 169
A.3.10EAN-8 .................................................................................. 170
A.3.11EAN-13 ................................................................................ 171
A.3.12Interleaved 2 of 5 ................................................................. 172
A.3.13MaxiCode ............................................................................ 173
A.3.14MicroPDF417 ...................................................................... 174
A.3.15OCR-A, OCR-B, US Currency ............................................ 175
A.3.16PDF417 ................................................................................ 187
A.3.17Postnet ................................................................................. 188
A.3.18QR Code .............................................................................. 189
A.3.19Reduced Space Symbology ................................................. 190
A.3.20UPC-A ................................................................................. 191
A.3.21UPC-E .................................................................................. 192
A.3.22UPC-E1 ................................................................................ 193
A.3.23ISBT ..................................................................................... 194
A.3.24British Post .......................................................................... 195
A.3.25Canadian Post ...................................................................... 196
A.3.26Australian Post ..................................................................... 197
A.3.27IATA 2 of 5 ......................................................................... 198
A.3.28Codablock F ......................................................................... 199
A.3.29Japanese Post ....................................................................... 200
A.3.30Planet Code .......................................................................... 201
A.3.31KIX (Netherlands) Post ....................................................... 202
A.3.32MSI ...................................................................................... 203
A.3.33TCIF Linked Code 39 .......................................................... 204
A.3.34Mayrix 2 of 5 ....................................................................... 205
A.3.35Korean Post .......................................................................... 206
MARS-1030 User Manual
vi
CHAPTER
Introduction
Congratulations on purchasing the MARS-1030 Portable Data Terminal
(PDT), a Microsoft Windows®CE .Net rugged PDT. Its special
combination of features makes it perfect for using in a wide range of
applications. These features as:
•
•
•
•
•
•
•
•
•
Intel® XScaleTM PXA255 400MHz 32 bits RISC Processor
Windows® CE .NET 4.2 Operating System
64/128/256 MB SDRAM & 64/128 MB Flash ROM
Open Architecture: User Accessible SD/CF/PCMCIA Slot
240 x 320, 3.5” Color TFT Display with Touch Panel
1 Numeric Keyboards with LED backlight
802.11b Radio Support (Bluetooth Optional)
Optionally Built-in GSM/GPRS Module
Integrated 1D or 2D Barcode Scanner
1.1 About this Manual
The following chapters contained in this manual are:
Chapter 1: Introduction --- Present the general information about the
PDT.
Chapter 2: Getting started --- Describe the basic use of the PDT.
Chapter 3: Setting – Provide basic instructions for customizing the PDT
by adjusting settings.
Chapter 4: Communication --- Describe how to use all kinds of
communication of the PDT.
Chapter 5: Software Application --- Offer the procedures of Software
implement.
MARS-1030 User Manual
1.2 User and Product Safety
•
•
•
•
Do not stare into the laser beam directly or shine it into eyes.
Never use strong pressure onto the screen or subject it to severe
impact, as the LCD panel could become cracked and possibility
cause personal injury. If the LCD panel is broken, never touch the
liquid inside, for such contact would irritate the skin.
Although the MARS-1030 PDT has been passed the test of IP54
standard for water and dust resistance, avoid prolonged exposure to
rain or other concentrated moisture. For these conditions exceed the
IP54 standard, and could result in water or other contaminants entering into the PDT.
Use only the approved AC Adapter with the PDT. Use of an unapproved AC Adapter could result in electrical problems, or even cause
a fire or electrical shock to the user.
•
Be sure that only authorized supplier are allowed to disassemble and
reassemble the device. If the device or parts has been damaged due
to any wrong handling, shall void the product and parts warranty.
•
Always make back-up copies of all important data. Easy done by
using a cable or Single Cradle (sold by optional) to transfer data to
the computer. Manufacturer is not liable for any data damages or
data loss caused by deletion or corruption by using of this device, or
due to the drained battery.
Lithium-ion battery packs might get hot, explode, ignite and/or cause
serious injury if exploded by abusive using. Please follow the safety
warnings listed as below:
•
– Do not place the battery pack in fire or heat the battery.
– Do not install the battery pack backwards so the polarity is reserved.
–
Do not connect the positive Battery pack with negative
battery pack to each other with any metal object (like
wire).
– Do not carry or store battery pack together with metal objects.
– Do not pierce the battery pack with nails, strike the battery pack
with a hammer, step on the battery pack or otherwise put it to
strong impacts or shocks.
– Do not solder directly onto the battery pack.
Chapter 1
– Do not expose battery pack to liquid, or allow the battery
contacts to get wet.
– Do not disassemble or modify the battery pack. The battery
pack contains safety and protection devices, which, if damaged,
may cause the battery pack to generate heat, explode or ignite.
– Do not discharge the battery pack using any device except for the
specified device. When it is used in devices other than the
specified devices, the battery pack can be damaged or its life
expectancy reduced. If the device causes any abnormal current to
flow, it may cause the battery pack to become hot, explode or
ignite and cause serious injury.
– In the event the battery pack leaks and the fluid gets into one’s
eye, do not rub the eye. Rinse well with water and immediately
seek medical care. If left untreated, the battery fluid could cause
damage to the eye.
MARS-1030 User Manual
1.3 Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for
help.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. To maintain compliance with FCC RF
exposure compliance requirements, please avoid direct contact to the
transmitting antenna during transmitting.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Chapter 1
Caution: SCC declares that MARS-1030 ID:M82-MARS-1030 is
limited in CH1~CH11 for 2.4GHz by specified firmware controlled in U.S.A.
The FCC ID of MARS-1030 is M82-MARS-1030
IMPORTANT FOR LASER PRODUCTS
1.
2.
3.
Class II Laser Product
Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
radiation exposure.”
“Laser Radiation – Do not stare into beam”
MARS-1030 User Manual
1.4 Product Labeling
The PDT has several labels as showed in Figure 1-1 and 1-2.
Figure 1.1: Product Labeling (Front side view)
Chapter 1
Figure 1.2: Product Labeling (Back side view)
MARS-1030 User Manual
1.5 System Specifications
The MARS-1030 PDT detailed specifications as follows. Unless
otherwise noted, all the specifications are subject to change without prior
notification.
Table 1.1: System Specification
MARS-1030
Processor
Memory
Display
Audio
Radio Support
Communication Ports
Scan Engine
(Optional)
Expansion Slot
LED
Power System
400MHz Intel PXA255 32 bits RISC CPU
64 or 128MB Flash ROM
64,128 or 256MB SDRAM
240 x 320 3.5” TFT 256K Color LCD with LED
backlight
One mono speaker
2.5mm DIA Stereo Earphone Jack with
Microphone input
Wireless LAN: 802.11b (optional)
Bluetooth: Class II (optional)
GSM/GPRS: (optional)
USB: Support USB v1.1 both host and client.
(PDT and Cradle)
Serial: RS232 via optional cable or Cradle.
Opticon Laser (1D) Engine
HHP 2D Imager.
One Compact Flash Type-II slot
One PCMCIA slot
One SD Card slot (support SD memory only)
One Triple-Color LED for Charger Indicator
and Alarm Notification
One Dual-Color LED for Scanner Indicator
Standard Li-Ion Battery Pack, 3.7V, 3000mAh
Advanced Smart Battery with Gas-Gauge
Built-in Battery Charger
2.4V/15mAh rechargeable backup battery
One Battery Cover Sensor Switch
Power Adapter: 100~240V AC, 50/60Hz Input
; 5VDC/2.6A, 3A Output
Chapter 1
-
Power button
4-way navigation button
4 Application Keys
Button/Key
3 Scanner Enable Keys
SW Reset input button
16 Alpha-numeric keyboard
Dimensions: 192.5mm (L) x 91.3mm /
78mm(W) x 42.2mm / 60.6mm (H)
Dimensions and Weight
- Weight: 560g with Standard Battery Pack
500g without Battery Pack
Color
- Black
- Standard Packing list:
1. MARS-1030 Terminal
2. Stylus
3. USB Client Cable for Terminal
4. Earphone/ Microphone Set
5. Standard AC Adapter 5VDC/2.6A
6. AC Power Cord
7. Standard Battery Pack (3.7V, 3000mAh)
8. CF Support Guide
9. Quick Guide
Standard packing list
and Optional
- Optional Accessory:
accessories
1. RS232 Serial Cable for Terminal
2. USB Host Cable for Terminal
3. High-Capacity Li-Ion Battery Pack
(3.7V, 4000mAh)
4. RFID Card Cover
5. Single Dock
6. Pistol Grip
7. 4-Slot Battery Charger
8. Car Adapter
9. Holster
10. Protect Film
Software
- Microsoft Windows CE.NET 4.2 Professional
MARS-1030 User Manual
10
1.6 Environment Standard
Table 1.2: Environment Standard
Operating Temperature
14oF ~ 122oF( -10oC ~ 50oC)
Storage Temperature
-4oF ~ 158oF (-20oC ~ 70oC)
5% ~ 80% (non-condensing)
5ft (1.5m) Drop to Concrete
IP54 Certificated & IP64 Compliant
MIL STD 810F
Humidity
Drop
Water & Dust proof
Vibration
11
Chapter 1
1.7 Warranty and after service
Should this PDT be malfunctioned, please contact your original retailer
providing information about the product name, the serial number, and the
details about the problem.
Use this table and the MAN paragraph formats to tag body content.
MARS-1030 User Manual
12
CHAPTER
Getting Started
2.1 Check the package
Open the package and check all the parts are inside without shortage and
damage:
Figure 2.1: Inside the package
1.
2.
3.
4.
5.
6.
7.
8.
9.
MARS-1030 Terminal
Stylus
USB Client Cable for Terminal
Earphone/ Microphone Set
Standard AC Adapter 5VDC/2.6A
AC Power Cord
Standard Battery Pack (3.7V, 3000 mAh)
CF Support Guide
Quick Guide (Not Shown)
MARS-1030 User Manual
14
2.2 General View of the PDT
2.2.1
PDT front side view
Figure 2.2: PDT Front side view
2.2.2
PDT back side view
Figure 2.3: PDT back side view
15
Chapter 2
Table 2.1: Description of PDT General View
Scanner LED Indicator
Charge LED Indicator
LCM / Touch Panel
Left Scan key
Right Scan key
Scan key
Power key
F1 ~ F4 key
Navigation key
Alpha-Numeric keys
Alpha key
10
Fn key
11
14
Enter key
Earphone Jack Connector
USB / Serial / Synchronization port
Scan window
15
Stylus
16
Battery Cover
12
13
17 Battery cover Latch
18 Hand Strap
19 Speaker
20 DC Power Jack
21
End Cap
MARS-1030 User Manual
“Red” color
Reading barcode
“Green” color
Successful reading
“Red” color
Charging battery
“Green” color
Battery charged full
Do specific action through touch panel by
stylus
Start scanning the barcode by pressing any
one of these three scan keys
Puts the terminal into and wakes the
terminal from suspend mode.
The four application keys, hot keys of
application program defined by end user.
Navigation keys for left, right, up and down
directions
Numeric keys, Change to Alpha keys after
pressing Alpha key.
Toggle Alpha-mode for Alpha-Numeric keys
This key is used in combination with other
keys to type special characters and perform
system functions.
This key confirms data entry
A connector to plug a earphone
A connector to support USB Host/Client
and serial functions
A window for scanning of barcode reader
Use the stylus for selecting items and
entering information.
Protect Battery pack, keep the switch of
battery cover to leave system from suspend
mode
To keep Battery Cover locked
This strap can be sealed tighter or looser
1.5W speaker for audio sound
A connector to support AC power.
Protect CF slot and SD slot from dust and
water
16
2.3 Charging the Battery Pack
Before using the PDT, perform the basic procedure of charging the battery pack through the following steps.
2.3.1
1.
Installing the battery pack
On the PDT attached with a hand-strap, detach and loose the handstrap.
Figure 2.4: Release the Hand strap from PDT
17
Chapter 2
2.
Turn the locking screws (right and left) downwards and lift the battery cover away from the PDT.
Figure 2.5: Detach the battery cover from PDT
MARS-1030 User Manual
18
3.
Insert the battery pack into the battery compartment with the label
facing out, and ensuring the battery snaps into place.
Figure 2.6: Insert the battery pack
19
Chapter 2
4.
Replace the battery cover by inserting the top first, and then press
the bottom in firmly. Turn the locking screws (right and left)
upwards to secure the cover to the PDT.
Figure 2.7: Replace the battery cover
5.
Charge time. For the first time to charge the battery pack needs
approximately 6 hours. Subsequent charging time needs approximately 4 hours.
•
When charging the battery pack, the charge LED indicator on the
PDT turns on Red. After the battery pack is fully charged, the
charge LED indicator turns to Green.
MARS-1030 User Manual
20
2.3.2
1.
2.
3.
Charging the battery pack with Power Adapter
Connect the Power cord to the Power adapter.
Plug in the connector of the power adapter.
Connect the power cord to a power source.
Figure 2.8: Charging with power adapter
•
•
When charging the battery pack, the charge LED indicator on the
PDT turns on Red.
After the battery pack is fully charged, the charge LED indicator
turns to Green.
21
Chapter 2
2.3.3
Charging the battery pack with Single Dock
a)
Leave the battery pack inside of the PDT
1.
2.
3.
4.
Connect the Power cord to the Power adapter
Connect the power cord to a power source
Plug in the connector of the power adapter with Single Dock
Insert the PDT into the Single Dock
Figure 2.9: Charging with Single Dock
•
When charging the battery pack, the charge LED indicator on the
PDT turns on Red. After the battery pack is fully charged, the
charge LED indicator turns to Green.
CAUTION: Single Cradle Adapter is 5Vdc/6.5A, which is different
from PDT Adapter (5Vdc/2.6A). Please use the Single Cradle
Adapter only.
MARS-1030 User Manual
22
b)
Place the spare battery pack into the Single Cradle’s spare Battery
charging slot
1.
2.
3.
4.
Connect the power cord to the power adapter
Connect the power cord to a power source
Plug in the connector of the power adapter with Single Cradle
Insert the Battery pack into the Single Cradle’s spare Battery slot.
•
When charging the Battery pack in the Single Cradle’s spare
Battery slot, the Single Cradle charging LED will turn on Red.
After the Battery pack is fully charged, this LED will turn to Green.
CAUTION: Please do not remove the Battery pack too long from
PDT after you have already full-charged the Battery pack and
backup battery pack and start to use the PDT. Otherwise the data
stored inside SDRAM memory will be lost. Please also keep in
mind power the PDT off if you want to change the main Battery
pack.
23
Chapter 2
2.4 Handling the PDT
2.4.1
Starting the PDT
Press the Power key to turn on/off the PDT. If the PDT does not power
on, perform a cold boot. See 2-7 Resetting on page 2-27.
CAUTION: When a battery is fully inserted in PDT for the first
time, upon the PDT’s first power up, the device boots and
powers on automatically.
When the PDT is powered
on for the first time, it
initializes its system. A
splash screen (figure 2-10)
appears for a short period
of time followed by the
Wince.NET 4.2 window.
Figure 2.10: Starting the PDT
MARS-1030 User Manual
24
2.4.2
•
Power on / off
To turn on the PDT
Press the Power key briefly ( ). If the PDT does not power on, perform
the cold reset. See chapter 2.7.1.
As the PDT initializes its file system, it splash screen displays for about
30 seconds followed by calibration screen. Every time you perform a cold
reset, these screens will also appear.
To turn off the PDT, just press the Power key again. This action does not
actually turn off the PDT, it only turns the PDT into suspend mode. All
running applications remain as you left them, until you press the Power
key again to resume operation of the PDT
2.4.3
Calibration of the touch Screen
On the initial boot-up of the PDT, the
stylus calibration screen (Labeled Align
Screen) opens. Use the stylus to press and
hold briefly on the center of each target as
it moves around the screen.
If necessary, adjust the backlight on the
PDT to make the screen readable. (See
below 2.4.4. Adjust the
brightness).
When you feel the touch screen
function is poor or the operation does not
match the exact location it should be,
please recalibrate the screen by using the
stylus to tap the Start > Settings >
Control Panel > Stylus, to open the
“Calibration” to
recalibrate again.
Figure 2.11: Calibration
25
Chapter 2
2.4.4
Adjusting the brightness
The factory default for the brightness is in Middle level. You can adjust
the brightness to meet your environment and comfort as:
key and then press on the right key
1) Become brighter: Press the
of Navigation key
key and then press on the left key of
2) Become darker: Press the
Navigation key
3) The display will become dimmer automatically, if you do not perform
any operation for a specific period of time. This will help to save the
battery power. You can set up the specific period of time to see chapter
2.7 as reference.
2.4.5
To mute the Sound
To mute the sound, press the
key first, and then press the
key to turn off and on of the sound.
2.4.6
Using the Stylus
The stylus is located next to hand-strap on the left rear of the PDT as
illustrated in figure 2-3 PDT Back side view (in page 2-3). The stylus
function is same as the mouse on a PC. Use the stylus to:
Navigate the display, select menu item and open optional applications.
Tap the characters on soft keyboard panel.
Hold the stylus on the screen and drag across the screen to select the list
of multiple items.
CAUTION: Never use a pen, pencil, or other sharp object on the
display to avoid any unexpected damage of the touch screen.
MARS-1030 User Manual
26
2.4.7
Using the Keypad
Figure 2.12: MARS-1030 Keypad
27
Chapter 2
Table 2.2: Table 2-2 Keypad List
Key
Fn + Main
Function
Main Function
Alpha + Main
Function
None. (Reserved for
Customer)
Main BarCode Scan
Key
Power On/Off
Internet Explorer
Microsoft WordPad
Inbox
File Explorer
Right
Backlight
Increase
Left
Backlight
Decrease
Down
Page Down
Up
Page Up
ESC
Audio Mute
Backspace
TAB (Tabulation) Caps
Change to letters
MARS-1030 User Manual
28
€
Key
Fn + Main
Function
Main Function
Alpha + Main
Function
Function change
(at)
’
(Plus Sign)
Paste
Del (Delete)
(Minus Sign)
Copy
(AND)
(Asterisk)
Space
. (Point)
Start Menu
Enter
(Backslash)
Table 2.3: Special Assembler Key
Assembler Key
Functionality
Definition
Warm Reset
Press “F1” and “F4” button
simultaneously.
Cold Reset
Press “Power”, “F1” and “F4”
button simultaneously.
29
Chapter 2
Table 2.4: Definition of main Function
Key
Main Function
Definition
None.
Keep its function or by customer
demand.
Main BarCode Scan
The
key activates the
Key
scan function of MARS-1030.
Power On/Off
The
key puts the terminal into
and wakes the terminal from
suspend mode.
Internet Explorer
Application key 1, User can
define F1 function from setting.
Microsoft WordPad
Application key 2, User can
define F2 function from setting.
Inbox
Application key 3, User can
define F3 function from setting.
File Explorer
Application key 4, User can
define F4 function from setting.
Move the cursor one character to
the right. The cursor will move
continuously if button is pressed
continuously.
Move the cursor one character to
the left. The cursor will move
continuously if button is pressed
continuously.
Move the cursor down one row or
line The cursor will move
continuously if button is pressed
continuously.
Move the cursor up one row or
line The cursor will move
continuously if button is pressed
continuously.
Right
Left
Down
Up
ESC
MARS-1030 User Manual
This key performs a cancel action
30
Key
Main Function
Definition
Backspace
“Backspace” key, it moves the
cursor back one space each time
the key is pressed. It deletes the
previous character each time it is
pressed if you are typing text. The
cursor will move continuously if
button is pressed continuously.
1. The
Change to letters
key enables you to
toggle between the numeric
and alpha modes. Numeric
mode is when you type numbers with number keys. Alpha
mode is when you type letters
with the number keys.
2. When you press
key, it
appears "Alpha" icon at the
Task bar to indicate Alpha
mode is enabled. The keypad
stays in the alpha mode until
you press
key again.
Function change
The
key is used in
combination with other keys to
type special characters and
perform system functions.
Number key “1”
Number key “2”
Number key “3”
Number key “4”
Number key “5”
Number key “6”
Number key “7”
31
Chapter 2
Key
Main Function
Definition
Number key “8”
Number key “9”
Number key “0”
Point key
Enter
This key confirms data entry
MARS-1030 User Manual
32
2.4.7.1 Special Function by “Fn” + main Function
The “Fn” key is used in combination with other keys to type special
characters and perform system functions.
Table 2.5: Special Function key define
Key Sequence
Fn + Main
Function
Definition
Increase the LED backlight brightness of
display screen(Lighter)
Backlight
Increase
You must press
key, then press
key to increase backlight brightness each time.
Decrease the LED backlight brightness of
display screen (darker)
Backlight
Decrease
You must press
key, then press
key to decrease backlight
brightness each time.
Move the cursor down one page. The
cursor will move continuously if button is
pressed continuously.
Page Down You must press
key, then press
key to cursor down one page
each time.
Move the cursor up one page. The cursor
will move continuously if button is pressed
continuously.
Page Up
You must press
key, then press
key to cursor up one page each
time.
Toggle the audio mute/on
You must press
key, then press
Audio Mute
key to enable audio mute or turn
on audio function each time.
33
Chapter 2
Key Sequence
Fn + Main
Function
Definition
The “TAB” function is to move the cursor
to the next tab stop or the next control (on
a form)
TAB
(Tabulation) To do this function by pressing
@ (at)
key first, and then pressing
each time.
key
Enter an {@, at} by pressing
key,
then pressing
key.
Enter a {’} by pressing
’
pressing
(Plus Sign)
key, then
key.
Enter a plus sign by pressing
then pressing
key,
key
It is to do “Paste” function.
To do this function by pressing
Paste
key first, and then pressing
Del (Delete)
key
each time.
The “Delete” function delete the next
character forward each time.
To do “Delete” function by pressing
key first, and then pressing
key each time.
(Minus
Sign)
Enter a minus sign by pressing
key, then pressing
key.
Copy action.
Copy
You must press
key, then press
key to do “Copy” action each
time.
MARS-1030 User Manual
34
Key Sequence
Fn + Main
Function
Definition
Enter an AND sign by pressing
(AND)
key, then pressing
key.
Enter an asterisk sign by pressing
(Asterisk)
key first, and then pressing
key.
The “Space” function is to move the cursor
one space.
Space
To do this function by pressing
key first, and then pressing
each time.
It displays the Start menu.
Start Menu
key
To do this function by pressing
key first, and then pressing
each time.
(Backslash)
key
Enter a backslash by pressing
first, and then pressing
35
key
key.
Chapter 2
2.4.7.2 Alpha plane keys by “Alpha” + main Function
1.
The
key enables you to toggle between the numeric and
alpha modes. Numeric mode is when you type numbers with number keys. Alpha mode is when you type letters with the number
keys.
2.
When you press
key, it appears “Alpha” icon at the Task
bar to indicate Alpha mode is enabled. It means Alpha mode is
disabled if there isn’t “Alpha” icon at Task bar. The keypad stays in
the alpha mode until you press
key again. For an example
to type “cap1” word, press
< wait
0.5 seconds >
3.
If you want to type a lowercase “c”, press
(The
key three times, the
key is needed if
it’s the first alpha character keying in.). If a letter that is on the
same key as the last letter entered, wait two seconds after you
pressed the last key, then you can enter the correct series of keystrokes to create the next letter.
4.
5.
While you are in the Alpha mode and you press
key to initial the Caps mode, you will render a Caps Lock until you press
key again. Once you are in Caps mode, you stay in Caps
until it is pressed again.
It appears “A” icon at Task Bar during Caps mode.
Table 2.6: Alpha + Numeric keys define
To enter
Press the Keys
To enter
€
Caps
MARS-1030 User Manual
36
Press the Keys
To enter
Press the Keys
To enter
37
Press the Keys
Chapter 2
To enter
Press the Keys
To enter
MARS-1030 User Manual
38
Press the Keys
To enter
Press the Keys
To enter
Press the Keys
Note:
1.
The
key is not needed to key in if the character isn’t the
first alpha character being keyed in.
2.
The
keys are not needed to key in if it is not the first capital
alpha character being keyed in.
39
Chapter 2
2.4.8
Using the Ear/Microphone
Connect Ear/Microphone to PDT earphone jack connector. The PDT is
not built in microphone; if you like to record the voice, you have to use
Ear/Microphone.
Figure 2.13: Ear/Microphone
MARS-1030 User Manual
40
2.5 Navigating the Display
2.5.1
Setting Time and Date
In the Date/Time options, you can change the year, month, date, time,
time zone, or select automatic adjust for Daylight Saving Time. To set or
change the date and time:
Figure 2.14: Date/Time properties
1.
2.
3.
4.
5.
6.
7.
Select Start > Settings > Control Panel > Date/Time
To change the year, select the year or open a numeric dial. Select
the up arrow to increase the value; select the down arrow to
decrease the value. Or you can type a new value in the field.
Select the month to open a
pull-down list of months or press the arrow buttons to either side of
the month to increase or decrease the month.
To change the time, select the hour, minute, seconds, or AM/PM
and select the up arrow to increase the value; select /tape the down
arrow to decrease the value. Or you can type a new value in the
field.
Select your correct time zone from the pull-down list.
To automatically adjust the clock for Daylight Saving Time, enable
the checkbox at the bottom of the screen.
Select Apply to make save your changes [and make additional
modifications] or select OK to exit the Date/Time settings.
41
Chapter 2
2.5.2
Entering the Data
To select and open programs, select Start > Programs from the task bar
to open a list of available programs. Or if the program has a icon on the
desktop, double-tap to open it.
There are several ways to enter data on the PDT once in an application:
•
•
•
•
•
Use the keypad to enter alpha-numeric characters, Refer to “2.4.7
Using the keypad” on page 2-11.
Use the stylus on the touch screen on page 2-11 for more information on using .the stylus.
Select text in the same way you select the text on a PC. Use the
stylus to highlight the desired text by dragging the stylus across the
desired text, double-tapping to select one word and triple-rapping
to select an entire line/paragraph. Refer to “2.5 Navigating the
Display” starting on page 2-21
Use the soft input panel (digital keyboard) with the stylus. Refer to
“2.5.5 The Soft Keypad” on page 2-23.
Use the bar code scanning to enter data. Press the trigger or “Bar
Code Start “ key to initiate a scan. The scanned data will enter the
current application’s open file. Refer to “2.5.7 Scanning Barcode”
starting on page 2-24 for more information on using a scanner.
For more information on factory installed applications, Refer to Chapter 4
“ Software Programs”.
2.5.3
The Command Bar
Use the Command bar at top of the screen to perform tasks in programs,
such a opening a file, or editing a file.
MARS-1030 User Manual
42
2.5.4
The Task Bar
The Task bar at the bottom of the screen displays the icon, an icon for the
active program, the current time, and system icons for utilities loaded in
memory. The Task bar includes menu names, buttons, and the keyboard
icon, which opens and closes the soft input panel (SIP). The Task bar
allows you to select and close programs. Refer to Figure 2-15 to view the
Task bar.
Command Bar
Task Bar
Figure 2.15: Task Bar & Command Bar
2.5.5
The Soft Keypad
In applications that accept keypad input, the soft input panel (SIP) can be
used to enter data using the stylus. The SIP is digital, QWERTY-style
keyboard.
To open the SIP, tap the keyboard icon to open the menu and select
Hide Input Panel to close the keyboard.
Use the stylus to select letters, numbers, or symbols from the Soft Input
Panel for the current application.
43
Chapter 2
2.5.6
Setting Up Wireless LAN RF
1) Press “Start”---“Setting”---“Control Panel” --- “WLAN Manager”.
2) Launch the WLAN Manager to Enable WLAN device.
3) Into AP Browser tab, tap Scan button to renew the network.
4) Select a network, tap the Join button or double tap it for more options.
5) Press OK to save all your Wireless LAN settings.
6) Tap the “Exit” button to Disable WLAN device.
Figure 2.16: WLAN Manager
MARS-1030 User Manual
Figure 2.17: WLAN Manager
44
Note:
802.11b WLAN is not connecting to network.
802.11b WLAN is no signal.
802.11b WLAN signal is Low.
802.11b WLAN signal is In General.
802.11b WLAN signal is Good.
Figure 2.18: WLAN Manager
Figure 2.19: WLAN Manager
45
Chapter 2
2.5.7
Scanning Barcode
To use the scanning function, complete the following steps:
1.
2.
3.
4.
5.
6.
7.
If you have not already done so, remove the protective plastic film
before using devices equipped with a laser scanner.
Select Start > Setting > Control Panel > Barcode Setting; complete all configurations following all description of 3.2.1 BarCode
Setting.
Run the WordPad software program
Aim the scanning beam at the center of bar code.
– Position the device close to bar code when scanning
– Position at a distance when scanning lager bar codes.
– The scanner is disabled after you release the key or after five
seconds.
Press the Right/left/central scan key. The scanner scans as long as
you hold the key or for five seconds.
Upon reading a bar code, the red LED indicator comes on until the
trigger is release or five seconds. The green LED and the beep tone
indicate a good read.
Barcode Scanning Position
This device can read from 40 to 300mm distance.
– Position the laser scanner close to the barcode when scanning
small barcodes. And position it in a distance from the barcode
when scanning large barcodes
MARS-1030 User Manual
46
– The reader can be detected by a red beam.
8.
Bad Scanning Position
– Make sure that the bars enter the laser beam when scanning
large barcodes.
– Scanning operations may fail if the laser beam positions as
below.
Note: this product scans using laser light. Never look directly into the
laser light or shine the laser light into the eyes.
2.5.8
Help
To tap “?” can get help information for each program.
47
Chapter 2
2.6 Power management
2.6.1
Suspend Mode
The PDT will go into a suspend
mode when it is idle for a period
of time. The idle
duration can be customized
using the Power control panel
(refer to Figure “Schemes Tab”)
Suspend mode works and looks
just like you have turned the unit
off. Press the
key to suspend
the PDT, Press the
key again
for the PDT to resume its Previous state.
Use the Battery power control
panel to set the duration to
switch state to Suspend mode
when system using battery
power. This will save battery
power when PDT is not in use.
Figure 2.20: Schemes Tab
MARS-1030 User Manual
48
Suspending:
The following conditions will suspend:
•
•
•
•
Press key while the unit is on.
The duration timer of item “Switch state to Suspend” expires,
which indicates that there has been no use for a specified of time.
The battery pack is completely discharged.
Tap Start > Suspend
Tap here to let PDT enter into
suspend mode
2.6.2
Resuming
Use one of following methods to resume (wake up the PDT):
•
•
Press key to suspend or resume (wake up).
Put the PDT into a dock.
When a battery pack completely discharges while the unit is in suspend
mode, the PDT remains suspended until discharged battery condition is
corrected.
49
Chapter 2
2.7 Resetting the PDT
2.7.1
Software (Warm) Reset
A warm reset is a transition from the on, idle, or suspend power state that
close all applications, clears the working RAM, but preserves the file system.
Reason to Warm Reset: If an application “hangs”, initiate a warm reset
to terminate the application only.
Process to Warm Reset: To a warm reset, press “F1” and “F4” button
simultaneously.
After Warm Reset:
•
•
The desktop appears with the application shortcuts on the screen.
The custom settings in the registry are persistent.
2.7.2
Cold Reset
You can use Cold Reset to initiate device if WINCE.NET OS lock up or
Warm Reset still can’t work
To perform Cold Reset, press “Power”, “F1” and “F4” button
simultaneously.
Device will initiate boot up after Cold Reset.
CAUTION: Only use the Warm Reset. Try warm reset before you
initiate Cold Reset. All applications will be Closed and working
RAM and all files will be cleared if you initiate the Cold Reset. It’s
better usually to back up your files to Flash ROM, Flash Card or PC.
MARS-1030 User Manual
50
CHAPTER
Setting
3.1 Introduction
To view available options for PDT’s setting, tap Start > Settings. Then,
there are three items inside Settings: “Control Panel”, “Network and
Dial-up” and “Taskbar and Start”.
3.2 Control Panel
To view the Control Panel and settings you can modify by tapping Start
> Settings > Control Panel.
Figure 3.1: Control Panel
MARS-1030 User Manual
52
3.2.1
BarCode Setting
CAUTIONPlease do not enter into any Barcode Application
Program before settings completing this Barcode.
There are three Tabs for scanner configuration
setting: “Basic” Tab, “Code Configure” Tab and
“Code ID” Tab. In addition, there is “BarCode
Setup” for the “Code Configure” Tab.
53
Chapter 3
3.2.1.1 “Basic” Tab
Figure 3.2: Basic Tab
MARS-1030 User Manual
54
Table 3.1: Basic Explaining
Field Name
Beep After Scan OK
Scan Timeout (sec)
Termination Code
Continuous Scan
Keybd Message
Function Explaining
Select the numbers of beep tone after scan OK.
After scanning the barcode, do
None
not give out beep sound.
After scanning the barcode,
One Time
give out beep one time.
After scanning the barcode,
Two Times
give out beep two times.
Select the scanning timeout duration
(in seconds) from this pull-down list. <2 ~ 20
sec, Default: 5>
After showing barcode, do not
None
action.
After showing the barcode,
CRLF
jump to next row.
After showing the barcode,
Space
jump one unit.
After showing the barcode,
Tab
jump a section.
Disable
Disable this functionality.
Alternate second number of
1 ~5 sec
Continuous Scan.
Select a method based upon the barcode
scanning application you will use.
A unit continues a unit, fast
Type Writing
showing barcode number.
Copy & Paste Once show barcode number
Prefix
Type the desired label prefix in this text box
Suffix
Type the desired label suffix in this text box
Default
Press “Default” button to reset all configuration
setting of “Basic” Tab into default values.
F/W ver.
Decoder firmware version.
Set All To Default
Press “Set All To Default” button to reset all
configuration setting of “Basic” Tab, “Code
Configure” Tab, “Code ID” Tab and all barcode
of “BarCode Setup” into default values.
55
Chapter 3
3.2.1.2 “BarCode” Tab:
Select the barcode symbologies you plan to scan from the list. Tap to
enable/disable the desired symbologies.
Figure 3.3: Code Configure Tab
Table 3.2: Code Configure Explaining
Barcode Symbology
Explaining
Type A. Numeric-only Barcodes
UPC-E
UPC-A
EAN-13 / ISBN
MARS-1030 User Manual
Compressed version of UPC code for
use on small products.
Universal product code seen on almost
all retail products in the USA and
Canada.
EAN-13: European Article Numbering
international retail product code.
ISBN: Special use of the EAN-13 symbol
to used internationally to mark books.
56
Barcode Symbology
EAN-8 / JAN-8
UPC-EAN Add-ON 2/5
Industrial 2 of 5 / IATA
Interleaved 2 of 5
Plessey / MSI
Code 11
Codabar / NW 7
Matrix 2 of 5
Explaining
Compressed version of EAN code for
use on small products.
UPC-A, UPC-E, EAN-13, and EAN-8
may all include an additional barcode to
the right of the main barcode. This
second barcode, which is usually not as
tall as the primary barcode, is used to
encode additional information for newspapers, books, and other periodicals.
Older code not in common use.
Compact numeric code, widely used in
industry, air cargo, other applications.
Plessey: Older code commonly used for
retail shelf marking.
MSI: Variation of the Plessey code
commonly used in USA.
Used primarily for labeling telecommunications equipment.
Older code often used in library systems,
sometimes in blood ban.
Used in miscellaneous industrial
applications, and mechanical numbering
systems.
Type B. Alphanumeric Barcodes
Code 39 / Code32
General-purpose code in very wide use
world-wide.
Code 93
Compact code similar to Code 39.
Code128 / UCC
EAN128
Very capable code, excellent density,
high reliability; in very wide use
world-wide.
Widely used data formatting model for
Code 128
Type C. Others Barcodes
China Post
Used by China Postal Service for
automated mail sorting.
Code 4
---
57
Chapter 3
Barcode Symbology
Explaining
GTIN
Global Trade Identification Number
Korea Code 3 of 5
---
RSS
Reduced Space Symbology
MARS-1030 User Manual
58
3.2.1.3 “Code ID” Tab:
Figure 3.4: Code ID Tab
Table 3.3: Code ID Explaining
Code ID is added into prefix of the barcode and let user identify which
kind of barcode being scanned.
Enable this functionality.
Enable Code ID
Set 1 ~ Set 5
User Define
Barcode List
Default
59
Select one default value by Set 1
~ Set 5.
(See the “Table 3-4 Code ID
Set1-Set5 Table”)
Establish number by oneself.
Set 1 ~ Set 5: defaults setting.
User Define: select barcode to
define.
Press “Default” button to reset all
configuration setting of “Code ID”
Tab into default values.
Chapter 3
Table 3.4: Code ID Set1-Set5 Table
Set 1
Set 2
Set 3
Set 4
Set 5
UPC-E
UPC-A
EAN-13 / ISBN
EAN-8 / JAN-8
Industrial 2 of 5 / IATA
Interleaved 2 of 5
Plessey / MSI
Code 11
Codabar / NW 7
Matrix 2 of 5
Code 39 / Code 32
Code 93
Code 128
Code 4
Korea Code 3 of 5
RSS
UCC128 / EAN128
MARS-1030 User Manual
60
3.2.1.4 BarCode Setup
A.
First select barcode type then select barcode to setting.
B.
Press “Default” button to reset all configuration setting of this barcode into default values.
C.
Press “Apply” button to be decided setting of this barcode.
Please see 3.2.2 Symbologies List for more detail information of each
Barcode.
Figure 3.5: BarCode Setup
61
Chapter 3
3.2.2
Symbologies List
A Type -- Numeric-only Barcodes
3.2.2.1 UPC-E
Figure 3.6: UPC-E
Table 3.5: UPC-E Explaining
Item
Explaining
Format
Ignore 1st digit
Transmit 1st digit
Send Check Digit
MARS-1030 User Manual
Do not transmit 1st digit by barcode.
Transmit 1st digit by barcode.
Whether send check digit by barcode.
62
3.2.2.2 UPC-A
UPC-A movements together with EAN-13, so only Enable EAN-13 then
UPC-A will be Enable, too.
Figure 3.7: UPC-A
Table 3.6: UPC-A Explaining
Item
Explaining
Format
Ignore 1st & 2nd digits
Transmit 1st digit
Transmit 2nd digit
Transmit 1st & 2nd digits
Send Check Digit
63
Do not transmit 1st digit by barcode.
Transmit 1st digit by barcode.
Transmit 2nd digit by barcode.
Transmit 1st & 2nd digits by
barcode.
Whether send check digit by
barcode.
Chapter 3
3.2.2.3 EAN-13 / ISBN
Figure 3.8: EAN-13 / ISBN
Table 3.7: EAN-13 / ISBN Explaining
Item
Explaining
Send Check Digit
Do not transmit 1st digit by barcode.
Transmit 1st digit by barcode.
Transmit 2nd digit by barcode.
Transmit 1st & 2nd digits by
barcode.
Whether send check digit by
barcode.
Enable ISBN Code
Whether use this ISBN Code.
Format
Ignore 1st & 2nd digits
Transmit 1st digit
Transmit 2nd digit
Transmit 1st & 2nd digits
MARS-1030 User Manual
64
3.2.2.4 EAN-8/JAN-8
Figure 3.9: EAN-8/JAN-8
Table 3.8: EAN-8/JAN-8 Explaining
Item
Explaining
Format
Ignore 1st digit
Transmit 1st digit
Send Check Digit
Convert to EAN-13
Add five 0
Do not transmit 1st digit by barcode.
Transmit 1st digit by barcode.
Whether send check digit by barcode.
When this option is selected the scanner
will convert UPC-E to UPC-A by
transmitting five zeroes …
Ahead of
Add five zeroes at prefix of the barcode.
code
After 3 digits Add five zeroes from 4th digits.
65
Chapter 3
3.2.2.5 UPC-EAN Add on 2/5
•
UPC-E, UPC-A, EAN-13 / ISBN and EAN-8 / JAN-8 may all
include an additional barcode to the right of the main barcode.
•
This barcode will show primary & additional code together.
•
So the UPC-EAN Add-ON 2/5 code is unable to use alone, must
operate in UPC-E or UPC-A or EAN-13 / ISBN or EAN-8 / JAN-8.
Figure 3.10: UPC-EAN Add on 2/5
UPC-EAN Add-On 2/5 Explaining
Item
2/5
Explaining
Only read the code with Addon Only reads the codes that have
addenda.
MARS-1030 User Manual
66
3.2.2.6 Industrial 2 of 5 / IATA
Figure 3.11: Industrial 2 of 5 / IATA
Table 3.9: Industrial 2 of 5 / IATA Explaining
Item
Explaining
Send Check Digit
Whether send check digit by
barcode.
Enable IATA Code
Whether use this IATA Code.
Checksum
Whether verify checksum by
barcode.
Verify
Min Length can be set from 2 to 48
Min-Max
(Default: 2 / 48)
Length
Max Length can be set from 2 to
48
Length 1 can be set from 2 to 48
Length 2 can be set from 2 to 48
Fixed
Length 3 can be set from 2 to 48
67
Chapter 3
3.2.2.7 Interleaved 2 of 5
Figure 3.12: Interleaved 2 of 5
Table 3.10: Interleaved 2 of 5 Explaining
Item
Explaining
Whether send check digit by
Send Check Digit
barcode.
Whether verify checksum by
Checksum
Verify
barcode.
Min Length can be set from 4 to
Min / Max 48
(Default: 4 / 48) Max Length can be set from 4 to
48
Length
Length 1 can be set from 4 to 48
Length 2 can be set from 4 to 48
Fixed
Length 3 can be set from 4 to 48
MARS-1030 User Manual
68
3.2.2.8 Plessey / MSI
Figure 3.13: Plessey / MSI
Table 3.11: Plessey / MSI Explaining
Item
Explaining
Format
Mode 10
Mode 10-10
Mode 11-10
Send Check Digit
1 Digit
2 Digits
Checksum mode for this barcode.
Whether send check digit by barcode.
Check 1 digit & send by checksum.
Check 2 digits & send by checksum.
69
Chapter 3
3.2.2.9 Code11
Figure 3.14: Code 11
Table 3.12: Code 11 Explaining
Item
Explaining
Send Check Digit
1 Digit
2 Digits
MARS-1030 User Manual
Whether send check digit by barcode.
Check 1 digit & send by checksum.
Check 2 digits & send by checksum.
70
3.2.2.10 Codabar / NW7
Figure 3.15: Codabar / NW7
Table 3.13: Codabar / NW7 Explaining
Item
Explaining
Start / Stop Digit
ABCD
abcd
TN*E
tn*e
Checksum
Verify
Whether transmit Start & Stop Digit.
Start / Stop transmit type
Whether verify checksum by barcode.
71
Chapter 3
3.2.2.11 Matrix 2 of 5
Figure 3.16: Matrix 2 of 5
Table 3.14: Matrix 2 of 5 Explaining
Item
Send Check Digit
Checksum
Verify
Min-Max
(Default: 4 / 48)
Length
Fixed
MARS-1030 User Manual
72
Explaining
Whether send check digit
by barcode.
Whether verify checksum
by barcode.
Min Length can be set from
4 to 48
Max Length can be set from
4 to 48
Length 1 can be set from 4
to 48
Length 2 can be set from 4
to 48
Length 3 can be set from 4
to 48
B Type -- Alphanumeric Barcodes
3.2.2.12 Code39 / Code32
Figure 3.17: Code39 / Code32
Table 3.15: Code39 / Code32 Explaining
Item
Explaining
Format
Code39 Standard
Code39 Full ASCII
Code32
Start / Stop Digit
Enable Code 39 Standard characters
Enable Code 39 Full ASCII character
Enable Code 32
Whether transmit Start & Stop Digit.
Verify
Whether verify checksum by barcode.
Transmit
Whether transmit checksum by
barcode.
Checksum
73
Chapter 3
3.2.2.13 Code93
The barcode do not have setting.
Figure 3.18: Code93
MARS-1030 User Manual
74
3.2.2.14 Code128 / UCC EAN128
Figure 3.19: Code 128 / UCC EAN128
Code128 / UCC EAN128 Explaining
Item
Explaining
Enable UCC128/EAN128.
Enable UCC128/EAN128
75
Chapter 3
C Type -- Others Barcodes
3.2.2.15 China Post
Figure 3.20: China Post
Table 3.16: China Post Explaining
Item
Explaining
Checksum
Verify
Send Check Digit
Min-Max
(Default: 4 / 48)
Length
Fixed
MARS-1030 User Manual
Whether verify checksum by barcode.
Whether send check digit by barcode.
Min Length can be set from 4 to 48
Max Length can be set from 4 to 48
Length 1 can be set from 4 to 48
Length 2 can be set from 4 to 48
Length 3 can be set from 4 to 48
76
3.2.2.16 Code4
The barcode do not have setting.
Figure 3.21: Code4
77
Chapter 3
3.2.2.17 GTIN
The barcode do not have setting.
Figure 3.22: GTIN
MARS-1030 User Manual
78
3.2.2.18 Korea Code 3 of 5
The barcode do not have setting.
Figure 3.23: Korea Code 3 of 5
79
Chapter 3
3.2.2.19 RSS
Figure 3.24: RSS
RSS Explaining
Item
Explaining
Convert to UCC128
Checksum
MARS-1030 User Manual
Verify
The scanner will convert RSS to
UCC128.
Whether verify checksum by barcode.
80
3.2.3
Bluetooth Device Properties
Table 3.17: Bluetooth Device Properties
ICON
ITEM & FUNCTION
• “Scan Device” Tab ( Figure 3-25) :
* Tap the Scan Device button to initiate a scan for Bluetooth
hardware. The Bluetooth manager lists the Bluetooth devices
that it finds, see Figure 3-26. If Bluetoothhardware is not
found the Bluetooth Hardware Error window appears, see
Figure 3-27. Table 3-18 described the Bluetooth Icons.
* Double tap the device to connect to on the device list. The
Bluetooth Manager Authentication window appears. Tap No
to connect to the device without authentication, or tap Yes to
authenticate the device before connecting. (Figure 3-28)
* If the Yes button was selected in the Bluetooth Manager
Authentication window, the enter PIN windows appears. Enter
a PIN (between 1 and 16 characters) in the Enter PIN: text
box, and tap OK. The mobile computer sends the PIN request
to the device for bonding. (Figure 3-29)
When prompted, the same PIN must be entered on the
other device. When the PIN is entered correctly on the other
device, the bonded icon appears on the device list. (Figure
3-30)
Figure 3.25: Bluetooth Manager
Windows
81
Figure 3.26: Bluetooth Manager
Windows
Chapter 3
Figure 3.27: Bluetooth Error
Windows
Figure 3.28: Bluetooth Manager
Windows
Figure 3.29: Bluetooth Enter PIN
Windows
Figure 3.30: Bluetooth Manager
Windows
Note: If the device to which the mobile computer is bonding
does not appear in the list, ensure it is turned on, in discoverable mode, and within range (30 feet / 10 meters) of the
mobile computer.
MARS-1030 User Manual
82
Table 3.18: Bluetooth Icon
Icon
Description
Unknown device icon
Locked icon
Not locked icon
Device is not defined
Device is locked and cannot be
bonded to.
Device is not locked and can be
bonded to.
Bluetooth device icon
Bluetooth device
Bonded device icon
Bonded Bluetooth device
Mobile device icon
Device is a mobile device
Phone icon
Device is a phone.
Printer icon
Device is a printer
Network icon
Device is a network.
Linked icon
Device is linked.
83
Chapter 3
3.2.4
Certificates
Certificates are used by some applications for establishing trust and for
secure communications.
Certificates are signed and issued by certificate authorities and are valid
for a prescribed period of time. Windows CE manages multiple certificate
stores.
Table 3.19: Certificates
ICON
ITEM & FUNCTION
• “Store” Tab ( Figure 3-31) :
* In the Stores tab, select the certificate store you wish to
view or modify from the drop-down list (Figure 3-32).
* The “Trusted Authorities “store lists the top-level
certificates for authorities you trust.( Figure 3-33 ,
Figure 3-34)
* The “My Certificates “store contains your personal
certificates, which you use to identify yourself.
* Intermediate certificate authorities that help establish a
chain of trust are stored in the “Other Authorities”
store.
• “Store” Tab :
* To add a certificate or associated private key to the
selected store, select “Import” (Figure 3-35).
* To view more details of the selected certificate, such as
the expanded name or expiration date, choose “View”.
* To delete the selected certificate from the store, choose
“Remove”.
MARS-1030 User Manual
84
Figure 3.31: Certificates
Figure 3.32: Certificates
Figure 3.33: Certificates
Figure 3.34: Certificates
Figure 3.35: Certificates
85
Chapter 3
3.2.5
Control Center
The Control Center includes four AP, listed the following ......
Figure 3.36: Control Center
3.2.5.1 Information
Table 3.20: Information
ICON
ITEM & FUNCTION
• “Information” Tab :
* Provide Software version, MAC address, Bluetooth ID,
Serial No. and Configuration No.
MARS-1030 User Manual
86
3.2.5.2 Brightness
Table 3.21: Brightness
ICON
ITEM & FUNCTION
LCD Brightness
Tune the LCD brightness by tapping right-arrow & left-arrow.
Can also tune the LCD brightness by pressing right-direction
key or left-direction key of keypad.
Amounts 7 steps: Every step have corresponding picture of
self.
1.
2.
6.
7.
3.
Enable Keypad Brightness
4.
5.
Open keypad brightness or
not.
Backlight Timeout
Save battery life by automatically turning off the backlight
when not used.
The table must disable when its item is
Battery
not marked.
Power, turn off
The table has 15 seconds, 30 seconds,
backlight after
1 minute, 2 minutes and 5 minutes.
AC Power, turn off The table must disable when its item is
not marked.
backlight after
The table has 15 seconds, 30 seconds,
1 minute, 2 minutes and 5 minutes.
Dim backlight Save battery life functionally of idleness
mode, open it or not.
after 20 seconds of
idleness.
87
Chapter 3
Figure 3.37: Brightness
3.2.5.3 Backup Restore
Table 3.22: Backup Restore
ICON
ITEM & FUNCTION
1. You can backup/restore system to/from flash disk or
inserted memory card. (A. Disk on Chip, B. CF Card,
C. SD Card) ( Figure 3-38)
2. When you launch this AP, it must check backup file in
DOC first. And if you select other storage, it will check
again.
3. Then if it has the file, appeared its date behind “Last
backup date:”; if not, disable “Restore Now” Button.
4. When you press the Backup/Restore Button will be a
warning dialog pop up. ( Figure 3-39)
5. When system backup/restoring finished will be a message dialog will pop up. (A. Backup: Figure 3-40, B.
Restore: Figure 3-41)
MARS-1030 User Manual
88
Figure 3.38: Backup Restore
Figure 3.40: Backup OK
Figure 3.39: Backup & Restore
Start
Figure 3.41: Restore OK
89
Chapter 3
3.2.5.4 Fn-key Settings
Table 3.23: Fn-Key
ICON
ITEM & FUNCTION
Fn-Key Setting (Figure 3-42)
Fn Key
The Application Program of default setting
F1
Internet Explorer
F2
Microsoft WordPad
F3
Inbox
F4
My Computer
* To assign your favorite application program to F1, F2,
F3 and F4 hot keys.
* Choose one of F1, F2, F3 and F4 from pull-down list.
(Figure 3-43)
* To tap “Browse…” inside “Assign program” applet.
* Select one application program you want from program
list, then, choose “OK”. (Figure 3-43)
* To tap “Default” to return back to default setting.
(Figure 3-42)
Figure 3.42: Fn-Key Settings
MARS-1030 User Manual
Figure 3.43: Fn-Key Settings
90
3.2.6
Date/Time
Table 3.24: Date/Time
ICON
ITEM & FUNCTION
• “Date/Time” Tab :( Figure 2-14)
* Please see the detail information of 2.5.1 Setting Time
and Date on P.2-21
3.2.7
Dialing Properties
Table 3.25: Dialing properties
ICON
ITEM & FUNCTION
• “Dialing Properties” Tab :( Figure 3-44)
* In the When dialing from list, select the “Location”
where you want to change settings.(Figure 3-45)
* To create a new location, select “New”. Enter the name
of the location, and then select “OK”.(Figure 3-46)
* Enter or edit the area code and local country code as
needed.
* In Dial using, select “Tone dialing” or “Pulse dialing”.
Most phone lines are tone.
* To automatically disable call waiting, select “ Disable
call waiting by dialing”, select the appropriate number
sequence in the list, or enter a new sequence.
• Editing dialing patterns (Figure 3-47)
* Using the codes listed in the topic; revise the dialing
patterns as needed.
Notes:
- If you need to use character other than the ones
listed here, use manual dialing.
- Hyphens and spaces in dialing strings are ignored.
- Some modems may not respond to the following
characters, even though your device lets you add
them to the dial string.
91
Chapter 3
Figure 3.44: Dialing Properties
Figure 3.45: Dialing Properties
Figure 3.46: Dialing Properties
Figure 3.47: Dialing Properties
MARS-1030 User Manual
92
3.2.8
Display Properties
Table 3.26: Display properties
ICON
ITEM & FUNCTION
• “Background” Tab :( Figure 3-48)
* From the “Image” list, select an image you want as the
background of the desktop.(Figure 3-49)
* To locate an image in another folder, select “Browse”.
* (Figure 3-50)
* To have the image cover the entire background, select
“ Tile image on background”
• “Appearance” Tab(Figure 3-51)
* Change the color scheme :( Figure 3-52)
- From the” Scheme” list, select a scheme.
- View your choice in the preview box. If you like the
scheme, select “Apply”.
* Create a custom color scheme:
- From the “Item” list, select a display item.
- From the “Basic colors” list, select a color, and
select “OK”.
- View your color selection(s) in the Preview box.
- To save the scheme, select “Save”.
- In the “Save this color scheme as” box, enter a
name for the scheme, and select “OK”.
- Select “Apply”.
Figure 3.48: Display properties
93
Figure 3.49: Display properties
Chapter 3
Figure 3.50: Display properties
Figure 3.51: Display properties
Figure 3.52: Display properties
MARS-1030 User Manual
94
3.2.9
Input Panel
Table 3.27: Display properties
ICON
ITEM & FUNCTION
• “Input panel” Tab :( Figure 3-53)
* Select the input method you want to change.
* To change the Soft Keyboard Options , tap “Option”
(Figure 3-54) .
• “Options” Tab :
* Change the soft keyboard options as desired,
selecting from:
- Large or small keys
- Using gestures for space, black-space shift, and
enter.
* To exit the soft keyboard Options, press “OK” on the
control bar, or press the key on the keypad.
* To exit the Input Panel, press “OK” on the control bar,
or press the key on the keypad..
Figure 3.53: Input Panel
Properties
Figure 3.54: Input Panel
Properties
95
Chapter 3
3.2.10 Internet Options
Table 3.28: Internet Options
ICON
ITEM & FUNCTION
• “General” Tab :( Figure 3-55)
* Type in the URL of desired start page and the desired
search engine. You also change the Cache Size, clear
the Cache and Clear the History..
• “Connection” Tab :( Figure 3-56)
* Modify the network access setting as desired.
• “Security” Tab (Figure 3-57)
* Modify the security settings as desired. You can enable
any of the following by tapping the checkbox:
- Allow cookies
- Allow TLS 1.0 security
- Allow SSL 2.0 security
- Allow SSL 3.0 security
- Warm when switching across secure and insecure
areas.
• “Advanced” Tab (Figure 3-58)
* Modify the security settings as desired. You can enable
any of the following by tapping the checkbox:
- Display Image in pages
- Play sounds in pages
- Enable scripting
- Display a notification about every script error
- Underline links> Never
> Always
> Hover
MARS-1030 User Manual
96
Figure 3.55: Internet Settings
Figure 3.56: Internet Settings
Figure 3.57: Internet Settings
Figure 3.58: Internet Settings
97
Chapter 3
3.2.11 Keyboard
Table 3.29: Keyboard
ICON
ITEM & FUNCTION
• “Repeat” Tab :( Figure 3-59)
* To change the amount of time between depressions
before repetition starts, adjust the Repeat delay slider
* To change the repeat rate, adjust the Repeat rate
slider.
* Test your new setting.
* Tap “ OK” to exit the “Keyboard” Tab.
Figure 3.59: Keyboard Properties
MARS-1030 User Manual
98
3.2.12 Network and Dial-up Connections
Table 3.30: Network and Dial-up Connections
ICON
ITEM & FUNCTION
• “Connection” Tab :
* To create a “Dial-up Connection”:
- Double-tap the “Make New connection”.
- In the “Make New Connection” dialog box, enter a
name for the connection.
- Select “Dial-Up Connection”.
- Select the “Next” button.
- Select the modem you want use.
- Select “Configure”
- Under “Connection Reference”, use the default
settings provided. If you can’t connect using these
settings, see your ISP or network administrator for
specific information. If you want to always enter a
phone number before connecting, Select “Manual
Dial”. Select “OK”.
- Select “TCP/IP Settings”. In the “General” tab,
ensure “Use Server-assigned IP address” is
selected. In the “Name Servers” tab, ensure “Use
Server-assigned addresses” is selected, and select
“OK”. If you are unable to connect with these default
settings, see your ISP or network administrator for
specific TCP/IP information.
- Select the “Next” button and type the telephone number.
- Select the “Finish” button.
The connection you just created appears as an icon in the
“Network and Dial-up Connections” folder.
- Set up a point-to-Point Protocol(PPP) account with
an ISP and obtain the following information:
> Access telephone number
> User name
> Password
99
Chapter 3
ICON
ITEM & FUNCTION
Once you have established an account, create a new
connection on your device. When creating this connection, you should be able to use all of the default TCP/IP
settings provided in the Make New Connection Wizard. If
you can’t connect using the default settings, contact your
ISP or access your ISP’s Web site for specific TCP/IP
information as well as primary and secondary DNS
address.
* Modify connection setting
- Select Start > Settings > Network and Dialup
Connections
- Select the icon for connection settings you want to
modify.
- Select File > Properties, or double- tap the
appropriate icon.
- Select desired options. There may be additional
settings that depend on the connection. To modify,
select the icon and select the icon and select
Advanced Settings… from the menu.
Figure 3.60: Network and Dial-up Figure 3.61: Network and Dial-up
Connections
Connections
MARS-1030 User Manual
100
Figure 3.62: Network and Dial-up Figure 3.63: Network and Dial-up
Connections
Connections
Figure 3.64: Network and Dial-up Figure 3.65: Network and Dial-up
Connections
Connections
101
Chapter 3
Figure 3.66: Network and Dial-up Figure 3.67: Network and Dial-up
Connections
Connections
Figure 3.68: Network and Dial-up Figure 3.69: Network and Dial-up
Connections
Connections
MARS-1030 User Manual
102
Figure 3.70: FNetwork and
Dial-up Connections
Figure 3.71: Network and Dial-up
Connections
103
Chapter 3
3.2.13 Owner
Table 3.31: Owner
ICON
ITEM & FUNCTION
• “Identification” Tab : (Figure 3-74)
* Fill in or edit the data as desired.
* To have this information displayed when you start your
device, select “Display Owner Identification” at
Power On.
* To set up identification for remote networks, see Setting
up identification for remote networks.
• “Network ID” Tab: (Figure 3-75)
* Enter the user name, password, and domain name you
use to log on to remote network.
Figure 3.72: Owner Properties
MARS-1030 User Manual
104
Figure 3.73: Owner Properties
3.2.14 Password
Table 3.32: Password
ICON
ITEM & FUNCTION
• “Password Setting” Tab : (Figure 3-76)
* Enter the password
* In the “Confirm password “box, enter the password
again.
* To require the password on startup, select “Enable
password protection at power- on“. and/or select
“Enable password protection for screen saver”
* To exit the Password control panel, press “OK” from
the control bar, or press the key on the keypad.
Figure 3.74: Password Properties
105
Chapter 3
3.2.15 PC Connection
Table 3.33: PC Connection
ICON
ITEM & FUNCTION
• “PC Connection” Tab : (Figure 3-77)
* Select the first checkbox to enable direct connections to
the desktop computer. (Figure 3-77)
* Tap the “Change Connection…” button to modify the
connection method from USB or Serial. (Figure 3-78)
* To exit the “Change Connection” dialog, press “OK”
from the control bar, or press the key on the
keypad.
* To exit the “PC Connection” properties control panel,
press “OK” from the control bar, or press the
key on the keypad.
Figure 3.75: PC Connection
MARS-1030 User Manual
106
Figure 3.76: PC Connection
3.2.16 Power
Table 3.34: Power
ICON
ITEM & FUNCTION
• “Battery” Tab : (Figure 3-79)
* Provide change level indicators for Main battery and
Backup battery.
* Provide remaining power capacity of main battery.
* If a “Main Batteries very Low” warning message shows,
the remaining battery life is around 30 minutes to
MARS-1030 shuts down. ( Figure 3-83)
* The PDT will shutdown during the main batteries
capacity is around 0%
* To exit Battery control panel, press “OK” from the
command bar, or press key on keypad.
• “ Schemes” Tab: (Figure 3-80)
* The Scheme Tab allows you to determine the time to
switch state to Suspend mode when using either
Battery Power or AC Power.
* Select Battery Power or AC Power as the power
scheme from the pull-down list.( Figure 3-80)
* Select the time to suspend mode from the pull-down
list. ( Figure 3-81)
• “Device Status” Tab: ( Figure 3-82)
Provide power level of device – The power level ranges
from “ High(D0)” which means the device is at the highest
power level to “Off(D4)” which means the device is at the
lowest power level.
Note:
This ICON inside the Task Bar shows that AC adapter
provides power to the PDT.
The ICON inside the Task Bar shows that Main Batteries
provides the power to the PDT.
The ICON inside the Task Bar shows that AC adapter
provides the power to the PDT and is charging the main
batteries.
107
Chapter 3
Figure 3.77: Power
Figure 3.78: Power
Figure 3.79: Power
Figure 3.80: Power
Figure 3.81: Power
MARS-1030 User Manual
108
3.2.17 Regional Settings
Table 3.35: Regional Settings
ICON
ITEM & FUNCTION
• “Region” Tab : (Figure 3-84)
* Select the desired location/language.
* Review the Appearance samples in the bottom half of
the screen.
* Select the Tab at the top for any settings you wish to
change, Options to modify include Number, Currency,
Time, and Date.
Figure 3.82: Regional Settings
109
Chapter 3
3.2.18 Remove Programs
Table 3.36: Remove Programs
ICON
ITEM & FUNCTION
• “Remove Programs” Tab :
* Only user installed programs can be removed.
- Select the program you wish to remove from the list
and press “remove” button.
MARS-1030 User Manual
110
3.2.19 Storage Manager
Table 3.37: Storage Manager
ICON
ITEM & FUNCTION
• “Storage Manager” Tab : (Figure 3-83)
* To change Storage properties control panel default
settings: Insert. Compact Flash(CF) or Secure digital
(SD) storage card into the unit.
- Select Start > Settings > Control Panel > Storage
Properties
- From the “Storage Info” pull-down list, select the
desired storage device.
- You can also format, dismount, and create
partitions on storage devices using this control panel.
- To save and exit the Storage Properties control
panel, press “OK” from the control bar, or press the
key on the keypad.
- Caution: Dismounting or formatting the DiskOnChip
will erase all files and program stored in Flash
Memory
Figure 3.83: Storage Manager
111
Chapter 3
3.2.20 Stylus
Table 3.38: Stylus
ICON
ITEM & FUNCTION
• “Double-Tap” Tab : (Figure 3-86,Figure 3-87)
* Double-tap the checkerboard grip at a comfortable
speed.
* Double-tap clapboard to test your settings
* The function is OK if the figures are changed from
Figure 3-86 to Figure 3-87.
* To tap “OK” to exit the Stylus Properties.
• “Calibration”: (Figure 3-88, Figure 3-89)
* In the Welcome Wizard, you tapped a target with the
stylus to set the amount of pressure needed for the
screen to respond to your stylus taps.
* Please also see 2.4.3 Calibration of the touch Screen
Figure 3.84: Stylus Properties
MARS-1030 User Manual
112
Figure 3.85: Stylus Properties
Figure 3.86: Stylus Properties
113
Figure 3.87: Stylus Properties
Chapter 3
3.2.21 System
Table 3.39: System
ICON
ITEM & FUNCTION
• “General” Tab : (Figure 3-90)
* To show:
- Firmware information
- Information about Processor type, Memory size,
Expansion card
• “Memory”: (Figure 3-91)
* Move the slider to adjust memory allocation. Default
storage memory is normally is normally set to about
8MB with the reminder assigned to Program memory.
* Press the “OK” key on the Keypad.
Note: the difference is occupied by OS between the RAM
size in Information properties and total memory size of
storage memory and program memory
• “Device Name” Tab : (Figure 3-92)
* Your device uses this information to identify itself to
other computers.
* The input panel will open to facilitate data entry.
* To close the Device Name, press the “OK” button, or
press the key on keypad.
• “Copyrights” Tab: (Figure3-93)
* Refer to this tab for specific copyright data. As a user,
you are responsible to read this statement.
MARS-1030 User Manual
114
Figure 3.88: System Properties
Figure 3.89: System Properties
Figure 3.90: System Properties
Figure 3.91: System Properties
115
Chapter 3
3.2.22 Volume & Sounds Properties
Table 3.40: Volume & Sound
ICON
ITEM & FUNCTION
• “Volume” Tab : (Figure 3-94)
* The factory default for Volume is the forth level. You
can adjust the volume to your environment and comfort.
- Set the volume by adjusting the slider from Soft to
Loud, or press Right or Left edge of Navigation keys
• “Sounds ” Tab: (Figure3-95)
* Enable the desired sounds for key clicks, screen taps,
notifications, and applications.
Figure 3.92: Volume & Sound
MARS-1030 User Manual
116
Figure 3.93: Volume & Sound
3.3 Taskbar and Start Menu
Table 3.41: Taskbar and Start menu
ICON
Taskbar and
Start Menu
ITEM & FUNCTION
• “General” Tab :
* In this tab, You can change the position of the Taskbar
and Start menu
- Is always on top or not
- Auto hide or not
- Show Clock or not
• “Advanced ” Tab:
* Tap the “Clear” button to remove the contents of the
Documents Menu.
* Enable “ Expand Control Panel” to list all icons of
Control Panel from top to bottom.
117
Chapter 3
MARS-1030 User Manual
118
CHAPTER
Communication
4.1 Installing & Setting Up Microsoft ActiveSync
4.1.1
Installing Microsoft ActiveSync on the Host PC
Microsoft ActiveSync is a file transfer tool to synchronize the files on a
PC with the files on your PDT.
To install Microsoft ActiveSync, complete the following steps on the PC:
1.
2.
3.
4.
5.
4.1.2
1.
•
•
2.
3.
Go to the Microsoft Windows CE.NET website and download the
latest current version of ActiveSync:
http://www.microsoft.com/mobile/pockeypc/downloads/ .
Install the latest version of Microsoft ActiveSync on the host PC.
Open ActiveSync.
Select File > Communication Settings from AtiveSync’s menu
bar.
Go to “Using ActiveSync” on page 4-1 to continue using ActiveSync.
Connecting PDT to Host PC
You can use either the USB/Serial (RS232) port of Single Dock or
a USB/Serial (RS232) cable to connect the PDT to the Host PC.
To use the dock, you must first insert the PDT into the slot, making
sure that the unit is firmly seated the dock.
To use the cable, connect the USB/Serial cable to the PDT.
Connect the USB/Serial dock or cable to the Host PC’s serial port
or USB port.
Connect the dock or PDT to the power adapter and power source.
MARS-1030 User Manual
120
4.2 Using ActiveSync
Use ActiveSync to transfer and synchronize files between the PDT and
the Host PC.
4.2.1
Setting up a Partnership
During the Microsoft ActiveSync installation, you were prompted to
create a partnership with your mobile device. When you set up a
partnership, you select synchronization and file conversation settings,
which are contained in a file on your desktop computer. This file enables
your desktop computer to recognize your device. Only devices that have a
partnership with a desktop computer can synchronize information
between the two computers.
For more information on partnerships, please refer to your Microsoft
ActiveSync documentation or help file.
Transferring Files:
To transfer files, complete the following steps on the host PC:
•
•
•
•
Select Start> Programs >Communication > (Serial, or USB)
Activesync.
Double-click on the selected ActiveSync icon
After you have established a connection with PDT, tap the
“Explore” button at the top of the ActiveSync window (or select
Explore from the File menu).
Navigate to the target directory on your PDT and copy the desired
file by using the Copy/paste method or dragging and dropping the
desired file(s) into the folder.
Figure 4.1: Communication
121
Chapter 4
4.2.2
ActiveSync File Synchronization
ActiveSync files synchronization requires an ActiveSync partnership
between the PDT and the Host PC. Refer to “Setting up a Partnership”,
above:
•
•
•
Select the files in the synchronization configuration for the PDT
partnership.
Select Tools > Options from the ActiveSync command bar to configure the synchronization options.
Place the file to be synchronized in the Synchronization folder
created you’re My Documents directory. Defaults to the desktop.
During the ActiveSync connection, all files in the Synchronization
folder will be synchronized to the \My Documents directory on the
PDT.
Figure 4.2: Connected
4.3 Networking
Please see the 3.2.14 Owner, Table 3-33 Owner on page 3-45 for setting
up the network ID. And see the 2.5.6 Setting Up Wireless LAN RF to
setup the 802.11b Wireless LAN for RF connecting.
MARS-1030 User Manual
122
CHAPTER
Software Applications
5.1 Introduction
The PDT includes Calculator, Inbox,…..
You can switch to any software program by tapping the Start Menu.
5.2 Software Applications
5.2.1
Calculator
It can process the basic numeric calculation with “+”, “-“ “*” and “/“.
5.2.2
Procedure:
– Tap numeric number
– Tap one operator “+”, “-“, “*” or “/”
– Then, tap another numeric number
– Tap another operator or numeric number if needed
– Tap “=” to get result
Button Function:
– “MC” – Clear memory
– “MS” – Store the displayed numeric number to memory
– “MR” – Read the newest stored numeric number
– “M+” – Add stored numeric number into the displayed numeric
number.
– “Backspace” – Same as “ backspace” key
– “CE” – Clear current keying numeric number. Same as “
Delete” key
– “C” – Clear the current calculation. Same as “ESC” key.
Inbox
Use Inbox to send and receive e-mail messages in the following ways:
Synchronize e-mail messages with Microsoft Exchange or Outlook
on the Host Computer.
Send and receive e-mail messages by connecting directly to an email server through an Internet server provider (ISP) or a network.
To setup “Inbox”:
Select Start> Programs> Inbox to open it.
MARS-1030 User Manual
124
*
Select Service> Options from the command bar. Drag the dialog to
show the right edge to configure e-mail.
Select “Add…” (Note 1)
In the “Service Type” list, select POP3 Mail or IMAP4 Mail.
(POP3 is the most common mail protocol for ISPs).Enter a unique
name for e-mail service in the “Service name” field. This name
cannot be changed later.
Select “OK”.
The Mail Service Setup wizard appears after you add a service. If
you are adjusting the setting of an existing service, select Service>
Options, select the service you are using, and then Properties. In the
Service Definition dialog box, complete the following entries as
needed:
– Connection: Select the name of the connection you created to
connect to the mail server. If you are receiving e-mail through a
network(Ethernet) connection, select Network Connection. If
you want Inbox to use your current connection, select (none). If
you have not created a connection, select Create new connection. Double-tap the “Make new Connection” icon, and follow
the instructions in wizard. When finished, select Inbox in the
Taskbar and continue setting up Inbox.
– POP3 Host(POP3 only): Enter the name of the mail server you
use to receive and send messages.
– Server(IMPA4 only): Enter the name of he mail server you use
to receive and send messages.
– User ID: Enter the user name or mailbox ID assigned to you.
– Password: Enter the password you use to access this mail
account. If you do not want to be prompted to enter the
password each time you connect, select “Save password”.
– Domain(Windows NT): Enter your Windows NT domain
name. This name is required only when connecting to networks,
such as a corporate network, that use Windows NT domain
security. This is not required for most ISP accounts. If you have
trouble connecting, try clearing this box.
– SMTP Host: If your mail service uses a separate server for
SMTP, enter the name in the box. If you’re setting up a POP3
Mail service with an ISP, the ISP must use an SMTP mail
gateway.
– Return Address: By default, the return address is set to
username@POP3host or username@Servername. Depending
125
Chapter 5
*
on the service you are using. If this is not your e-mail address,
enter the correct address in the box.
Set general preferences:
If you are adjusting the setting of an existing service, select Service> Options, select the service you are using, select Properties,
and then select Next. In the General Preferences dialog box,
choose any of the following setting settings, all of which are
optional:
– Disconnect service after actions are performed: Select to
automatically disconnect from the server upon completion of all
pending actions. This option minimizes connect time and cost.
– Check for new messages every: select the time interval(in
minutes) at which you want the device to check for new mail. If
this option is turned off, you must check for new mail manually
by selecting Services> Send/Receive Mail.
– Display a message box when new mail arrives (POP3 only):
Select to be informed that new mail has arrived.
– Display a message box when new mail arrives (IMAP4 only):
Select to be informed that new mail has arrived.
– Send using MIME format (POP3 only): Select to send messages with extended characters.
– Only display messages from last 3 days: Select how many
day’s messages you want downloaded.
Set inbox preferences
If you are adjusting the settings of an existing service, select Services> Options, select the service you are using, select Properties,
and then select New twice. In the Inbox Preferences dialog box,
choose any of the following options:
– Get message headers only: Select to save storage space and
time by downloading only headers. You can download a full
copy of the message later by selecting the message and then
Services> Get Full Copy.
– Include lines: Select to set the message length
(approximate number of lines) that you want to download.
– Get Full Copy of messages: Select to receive a full copy of all
messages. In addition to the message body, any options you
select in When getting full copy will be downloaded. Selecting
this option increases the amount of time needed to download
messages.
MARS-1030 User Manual
126
– Only synchronize folder hierarchy under Inbox (IMAP4
only): Select to speed download time by preventing the complete downloaded of the folder list every time you connect.
– Get meeting requests (POP3 only): Select to download and
store copies of meeting requests when getting full copies of
messages. This setting applies whether you have chosen to
download full copies of messages by default, or you selectively
download full copies of messages by opening the message and
selecting Services> Get Full Copy Limitations apply.
– Get file attachments (POP3 only): Select to download and
save message attachments when getting full copies of messages.
This option may use significant RAM and slow download time.
This setting applies whether you have chosen to download full
copies of messages by default, or if you selectively download
full copies of messages and selecting Services> Get Full Copy.
– Get file attachments and meeting requests (IMAP4 only):
Select to download and store meeting requests and message
attachments when getting full copies of messages. This setting
applies you have chosen to download full copies of messages by
default, or if you selectively download full copies of messages
by opening the message and selecting Services> Get Full Copy
Limitations apply.
– Only if small than (IMAP4 only): Select to restrict the size
of the attachments you download. Set to 10K if you want
to receive meeting requests only.
Include the original message in a reply:
– Select Services> Options> Compose tab.
– Under Reply, select Include Body. This setting will place a
copy of the original message beneath your response text.
– To indent the original message, select Indent.
– To add leading characters (such as>) to the original message
lines, select Add leading character, and enter the character
you want.
Save copies of sent messages:
By default, sent messages are not saved on your device.
– Select Services> Options> Compose tab.
– Select Keep copy of sent mail in Sent folder.
Set the action to follow deleting, moving, or responding to a
message:
127
Chapter 5
– Select Services> Options > Read tab.
– Select desired options.
Delete a message:
Select the message and select File> Delete. Messages are moved to
Deleted (local) folder and deleted according to the option you have
selected in Services> Options> Delete tab:
– On connect/disconnect: Deletes messages when you connect
or disconnect from your mail service or exit Inbox.
– Immediately: Deletes messages as soon as you select File>
Delete.
– Manual: Deletes messages when you select File> Empty
Deleted (local)
Note: If you are working offline, messages that have been deleted from
the device the next time you connect.
Empty the Deleted (local) folder:
– Select File> Empty Deleted (local). This permanently deletes
messages in the Deleted (local) folder.
– To check or adjust the current settings for deleting messages,
select Services> Options> Delete tab.
Move or copy a message:
Caution: When you move a message that you have received
through POP3 or synchronization to a folder you created on your
device, the copy of the message on the server is deleted. This prevents duplicate copies of messages. Although the complete message
is moved, message attachments will be deleted if you have not
selected the option to download attachments. Once the message is
moved, you will be able to access the message only from your
device.
•
– Select the message
– Select File> Move To or File> Copy To.
– Select the destination folder. If you are working offline, the
message will be moved or copied from the server the next time
you connect.
FolderCreate a folder:
– Select File> Folder> New Folder
– Type a name for the folder.
MARS-1030 User Manual
128
•
•
•
Delete a folder:
– Select the folder you want to delete
– Select File> Delete
Designate a folder as offline:
Only IMAP4 folders can be designated as offline. All IMAP4
default folders, such as Inbox, are automatically designated as
offline. Messages in offline folders can be viewed when you are
disconnected from your mail server. If a folder is not designated as
offline, you will be able to read and respond to messages in that
folder only when connected to the server.
– To designate a folder as offline, select the folder and then select
Service > Offline Folder.
Rename a folder:
– Select the folder you want to rename.
– Select File> Folder> Rename Folder.
– Type the new name for the folder.
Notes:
•
•
•
Default folders, such as Inbox, can’t be renamed.
Folders you create for IMAP4 mail servers can’t be renamed.
Synchronize folders while connected:
When you synchronize folders, the contents of your device folders
and mail server folders are compared and updated. New mail messages are downloaded, and messages in your device Outbox folder
are sent. The synchronization behavior depends on how you connect to your mail server.
– When you connect to a POP3 server, the Inbox and Outbox
folders on your device are synchronized with the corresponding
folders on the mail server. To synchronize after the initial connection, select Services> Send/Receive Mail.
– When you connect to an IMAP4 server, Inbox, Outbox, and all
folders marked as offline are synchronized. To synchronize all
folders after the initial connection, select Services> Synchronize Folders. To synchronize just the selected folder and the
Outbox folder, select Services> Send/Receive Mail.
Compose and send a message:
– In list view, select Compose> New Message
– Enter the address of one or more recipients, separating them
with a semicolon. If the recipient is listed in the Address Book,
enter a few letters of the recipient’s name and select Compose>
129
Chapter 5
Check Name. If there is only one match, the e-mail address is
inserted. If there is more than one match, select the correct
address from the Choose E-mail Recipients dialog box. If
there is no match then add a new e-mail address through
Choose E-mail Recipients.
– To attach a file, select File> attachments> Add Attachment.
– Select File> Send. If you are working offline, the message is
moved to the Outbox folder and will be sent the next time you
connect.
Tip: to see more header information, select the triangle in the lower-right
corner of the header area. Select the triangle again to collapse the header
area.
Save a message:
– Select File> Save to save the message you are composing or
editing.
The message is not sent and is saved in the inbox folder of the
active service.
Reply to or forward a message:
– Open the message, and then select Compose> Reply to
Sender, Reply to All, or Forward.
– Enter your response.
– Select File> Send.
Tips:
•
•
Selections in the Options dialog box determine whether the original
text is included.
To see more header information, select the inverted triangle in the
lower-right corner of the header area. Select the triangle again to
collapse the header area.
Check Inbox status:
– In list view, select Compose> Status. You can view details
such as the number of messages to be sent, deleted, and copied,
and the number of attachments to be downloaded.
Download message from the server:
– When you download messages, you need to create two connections: a remote connection and a mail server connection. The
remote connection connects you and your ISP or network. The
mail server connection downloads messages from your mail
MARS-1030 User Manual
130
–
–
–
–
server to Inbox on your device. When you select Services>
Connect in Inbox, Inbox starts a remote connection using the
connection you specified when setting up the current mail service. If you are already connected through a remote connection
other than the one you specified in the service, you will be
asked if you want to use the current connection. If you choose
not to, you will need to disconnect from the current connection
before you can check for new messages.
Select the Services menu and make sure that the service you
want to use is selected (the selected service has a bullet next to
it.)
Select Services> Connect. The messages on your device and
mail server are synchronized: new messages are downloaded to
the device Inbox folder, messages in the device Outbox folder
are sent, and messages that have been deleted on the server are
removed from the device Inbox. Double-tap a message list to
open it.
If you read a message and decide that you need the full copy,
select File> Get Full Copy while in the message window or
Services> Get Full Copy while in list view. This will also
download message attachments and meeting requests if you
have those options selected in the Inbox Preferences dialog
box. You can also choose to download full copies of messages
by default.
When finished, select Services> Connect to disconnect. You
also need to disconnect your dial-up connection by double-tapping the icon in the status bar and selecting Disconnect.
Notes:
•
•
•
Receiving entire messages consumes storage memory.
The size column in the Inbox list view displays the local size and
server size of a message. Even when a message has been downloaded fully, these numbers may differ because the size of a message can very between the server and the device.
When using IMAP4 to get Outlook + data, you will see the contents
of your Journal folder. File editing transactions and documents
(such as Task items, e-mail message, and Word documents)
attached using drag and drop will appear as shortcuts on the device.
A copy of the document will not be moved to your device, and the
shortcut on the device cannot be used to access the documents associated with a journal entry to the device, attach the document to the
131
Chapter 5
*
entry rather than dragging and dropping it. Also, be sure to set your
IMAP4 service to receive full copies of messages, attachments, and
meeting requests. For more information on using Journal, see the
Help for the desktop version of Outlook.
Working with Message Attachments:
– If you receive messages through a remote mail server, in Inbox
on the device, select the Get file attachments and meeting
requests (IMAP4) or Get meeting requests (POP3) setting in
the Inbox Preferences dialog box. For more information, see
Set Inbox preferences.
Notes:
•
•
Embedded images and OLE objects cannot be received as attachments
Embedded messages can be viewed as an attachment when using
IMAP4 to receive e-mail. However, this features does not work if
TNEF is enabled so that you can receive meeting requests.
Check attachments status:
– An attachment sent with an e-mail message, whether it has been
downloaded or not, will appear as an icon at the bottom of the
message in its own window pane. If you don’t see this pane,
select File> Attachments> Show Attachments. If TNEF is
turned on so you can receive meeting requests, you will not see
attachments until they are fully downloaded.
– To mark an attachment for downloading in a POP3 or IMAP4
service, double-click it. The attachment will be downloaded the
next time you connect. You can also set Inbox to download
attachments automatically when you get a full copy of a message. For more information, see Receive attachments.
Open an attachment:
– With the message open, double-tap the attachment’s icon at the
bottom of the message. If you don’t see this pane, select File>
Attachments> Show Attachments.
Store an attachment:
– Select Service> Options> Storage tab.
– Select to store attachments on internal RAM or a storage card.
– If you use more than one storage card, select it from the list.
MARS-1030 User Manual
132
Note: Once you make the above selection, all attachments will be moved
to the selected card.
Delete an attachment:
– To delete an attachment from a message you are sending, select
the attachment, and then select Edit> Clear or press the DEL
key on the keypad.Delete an attachment:
– To delete an attachment you have received, delete the message.
Attach a file to a message:
– With the message open, select File> Attachments> Add
Attachment.
– Select the file you want to attach.
Note:
OLE objects cannot be attached to Inbox messages.
Note 1: To add a mail service, select “Add”, To remove a mail service,
select the service from the Installed service box and select “Remove”.
To view a mail service’s properties, select the service from the Installed
service box and then select Properties.
Figure 5.1: Inbox
133
Chapter 5
5.2.3
Internet Explorer
With Internet Explorer, you can view Web or intranet Web pages on your
device. You will need to use a modem or WLAN to connect to an Internet
server provider (ISP) or network.
5.2.3.1 Connect to the Internet
Before you can view Web pages, you
must set up a remote connection to
your ISP or
network.
5.2.3.2 Start Internet Explorer
Open Internet Explorer by
selecting Start > Programs >
Internet Explorer.
To get default home page, navigate to the desired default web
page.
Select View > Internet Options
from the command bar.
Enter the desired URL in the
Start page field.
Press the OK button.
Figure 5.2: Internet Explorer
5.2.3.3 Navigation Control
Internet Explorer uses sliding menus for application and navigation
control. Tap and drag the sliding menus to the left or right to see the
hidden menu items and toolbars.
To achieve more screen real estate in Internet Explorer, you can hide the
Status bar and View menu. From the top menubar, go to View > Hide
Toolbars.
Once it is hidden, you must cold reset to access these features again.
Refer to 2.7.2 “Cold Reset “for more information.
MARS-1030 User Manual
134
5.2.3.4 Set up a proxy server
Proxy servers are often used when connecting to the Internet through a
local network, such as a corporate network, for added security.
Select View > Internet Options > Connection Tab.
Select Access the Internet using a proxy server.
Enter the proxy server address and port. For more information, see
your administrator.
To bypass the proxy server for local address, such as corporate
intranet pages, select Bypass proxy for local address.
5.2.3.5 Enable Cookies
A cookie file contains information about your identity and preferences so
that a Web site can tailor information to your needs. The Web site sends
the file and it is stored on your mobile device.
Select View > Internet Options > Security Tab.
Select Allow cookies.
5.2.3.6 Search for an Internet Site
Select View > Go > Search to search the web.
5.2.3.7 Go to an Internet address
Select Address Bar, if necessary to display the Address bar
Enter the address
Press “ENTER” key.
5.2.3.8 View previously visited sites
Tap the Arrow button at the right site of Address Bar
Select the Web Address you want to view.
5.2.3.9 Add and view Favorites
Go to the page you want add
Select Favorites > Add To Favorites.
If necessary, locate the folder you want.
Confirm or change the name.
135
Chapter 5
*
To view your favorite Web sites, select Favorites and the Web site
you want to view.
Note:
To organize your Favorites list, select Favorites > Organize Favorites.
5.2.3.10 Browse Web pages
To move to a page you have previously view, select View > Back
To move to the next page (provided you have viewed it previously),
Select View > Forward.
To return to your Home page, select View > Go > Home.
5.2.3.11 Refresh current page
Select View > Refresh.
5.2.3.12 Stop loading a page
Select View > Stop.
5.2.3.13 View current page
Select View > Internet Options
To view the protocol, page type, size, and address, selects the General tab.
To view security information about the page, select the Security
tab.
5.2.3.14 View HTML source code
While viewing the page, select File > Save As and save the file as
.txt file.
Open the file in a word processing program, such as WordPad.
5.2.3.15 Change home and search page settings
Open the page you want to use as your home or search page.
Select View > Go > Home or Search.
MARS-1030 User Manual
136
5.2.3.16 Save a copy of current page
You can save Web pages and view them later when you’re disconnected
from the Internet or Intranet without using cached memory.
Select File > Save As
Specify a folder location and give the file name.
5.2.3.17 Copy a Web page to a document
Select all or part of the Web page you want to copy.
Select Edit > Copy.
Go to the document where you want to place the information and
select the location.
Select Edit > Paste.
5.2.3.18 Select security Options
Select View > Internet Options > Security tab
Select the security protocols you want.
5.2.3.19 Change the font size
Select View > Text Size and select the desired size.
137
Chapter 5
5.2.4
Media Player
The PDT comes with Media
Player for Windows CE.NET
installed.
Open Media Player by
selecting Start > Programs > Media Player
from the desktop.
Select File > Open to
open a new media file.
Please refer to
www.microsoft.com for
additional information
and help with your
Microsoft Windows
Media Player.
Figure 5.3: Media Player
5.2.5
Messenger
The Windows CE Messenger client application in Windows
CE.NET allows you to communicate real-time using text-based
messaging, VOIP, and more.
See who’s online. See when your colleagues are online. You can
also post your presence information to a list of watchers that you
define.
Talk instead of type Stop typing Talk with a colleague anywhere in
the world using the microphone and speakers on your device. Windows Messenger supports high-quality voice calling r Windows CE
device.
Communicate using Session Initiation Protocol (SIP) or Hotmail
contacts Windows Messenger supports. Communication with your
colleagues in the enterprise with a SIP based communications service. You can also talk to your Hotmail contacts using the .NET
Messenger.
MARS-1030 User Manual
138
5.2.6
Microsoft WordPad
You can create and edit documents and templates in WordPad, using buttons and menu commands that are similar to those used in the desktop
version of Microsoft Word. You can work with files Normal or Outline
view.
WordPad documents are usually saved as .pwd files, but you can also
save documents in other file formats, such as .rtf or .doc.
5.2.6.1 Selecting and Editing Text
Select text
To select
Do this
Any amount of text
A word
A single paragraph
An entire document
An picture
Drag the stylus over the text.
Double-tap the word.
Triple-tap within the paragraph.
Select Edit > Select All
Tap the picture
Find text
– To search for text in one part of a document, select that part.
Otherwise, the whole document is searched.
– Select Edit > Find
– Enter the text you want to find. For a paragraph, enter ^p. For a
tab stop, enter ^t.
– Select the search options you want.
– To continue searching, select Edit > Find > Next.
Replace text
– To replace text in one part of document, select that part. Otherwise, the whole document is searched.
– Select Edit > Replace.
– Enter the text you want to find and the text you want to replace
it with. For a paragraph, enter ^p. For a tab stop, enter ^t.
– Select the replacement options you want.
– Select Find Next.
– On the Find/Replace toolbar, select the appropriate button.
139
Chapter 5
*
Move, copy, or delete text
– Select the text you want to move, copy, or delete.
– To move or delete text, select the Cut button. To copy the text,
select the Copy button.
– To paste the information, move the insertion point to the desired
location, and select the Paste button.
Notes:
•
•
To undo an action, select Edit > Undo.
To restore the action, select Edit > Redo.
5.2.6.2 Formatting Text
Create bulleted and numbered lists
– Select the Bullets or Numbering button.
– Type the first item.
– Press ENTER, type the next item, and repeat as needed.
– Select the button again to end list formatting.
Note: To change the number style for the selected list, select Format >
Paragraph, In the Format list, select the style you want.
Set the default font
– Select Format > Font.
– Select the font you want.
– Select Set As Default
– To confirm that your changes will be applied to subsequent documents you create, select Yes.
Note: To apply the default font and stylus to selected text, select Apply
Default.
Select a different font
– Select the text you want to change. To select all text, select Edit
> Select All.
– From the Font list, select the font you want.
– From the Font Size list, select a size.
Note: To see more formatting options, select Format > Font.
MARS-1030 User Manual
140
*
Change font formatting
– Select desired text.
– Select the Bold, Italic, or Underline button.
– To change the color, select Format > Font and select the color
you want from the Color list.
Adjust the paragraph alignment
– Select the paragraph you want to align.
– Select the Align Left, Center, or Align Right button.
Note: To see more formatting options, select Format > Paragraph.
Indent a paragraph
– Select the paragraph you want to indent.
– Select Format > paragraph.
– Adjust the indentation settings as needed.
Set tabs
– Select Format > Tabs.
– Change the tab settings as needed.
5.2.6.3 Adjusting the Display
Wrap text in the window
– Select View > Wrap to Window.
Display the document using the full screen
– Select View > Full Screen.
– To exit Full Screen view, select Restore.
– To move the Restore button, drag the bar on the left side.
Display or hide scroll bars
– Select View > Horizontal Scroll Bar or Vertical Scroll Bar.
Zoom in or out
– Select View > Zoom, and select the desired percentage.
Note: For Custom, enter the exact percentage and select OK.
141
Chapter 5
5.2.6.4 Working in Outline View
Switch between Normal and Outline views
– Select View > Normal or Outline.
Assign and change outline levels
– Select View > Outline.
– Select the appropriate buttons on the toolbar.
5.2.6.5 Inserting Symbols
Place the insertion point where you want to insert the symbol.
Select Tools > Insert Symbols.
Select the symbol you want, and then select Insert.
Tips:
If you select a different font ( or subset of a font), a different set of Symbols will be displayed.
5.2.6.6 Printing a Document
Select File > Print.
Select the printing options you want.
Tips:
•
•
Port list the available printer ports
If Network is selected from the Port list, enter the path to the network printer to the Net Path box.
5.2.6.7 Setting a password for a Document
Select File > password.
Type and verify the password.
You must save the document (File > Save) to return the password.
5.2.6.8 Converting Documents
About document conversion
If an e-mail program is installed on your device and you receive an
attached Word document or template created in Word version 6.0
or later, WordPad will convert the file on your device. To view the
MARS-1030 User Manual
142
document, simply open the attachment in your e-mail program or
open the file in the WordPad.
During conversion, some formatting attributes may be changed or
lost. To avoid losing these attributes permanently, close the file
after viewing it rather saving the file on your device. If you save the
file, save with a different file name.
For more information about conversion performed on your device,
see the following topics.
•
•
Changes caused by Word document conversion
Formatting
– Borders and Shading
Borders and shading are not displayed in WordPad, but are
restored when converted back to a Word document. Shading is
not restored when used in a table, but simple borders are
restored.
– Character formatting
Bold, italic, strikethrough, superscript, subscript, and hidden
text are retained and displayed. Other effects are changed or
removed.
– Colors
Colors are retained and mapped to colors available on your
device.
– Fonts and font sizes
Fonts not supported by your mobile device are mapped to the
closest font available in WordPad.
– Page Formatting
Headers, footers, footnotes, columns, pages setup information,
and style sheets are removed during conversion to WordPad.
WordPad supports built-in headings.
– Paragraph formatting
Tabs, alignment, bullets, indentation, simple numbered lists,
and paragraph spacing are retailed and displayed in WordPad.
Pictures
Pictures are removed during conversion.
143
Chapter 5
•
Table of Contents
Table of Contents text and some formatting are preserved. However, any text set at right-aligned tab stops may wrap to the next
line.
•
Index
Index text and some formatting are preserved.
•
Tables
Tables appear as tab-delimited text. Cells containing wrapped text,
tabs, or paragraph markers may be difficult to read. Simple tables
are displayed accurately and restored when you convert the WordPad file back to a WordPad document.
•
OLE Objects
OLE Objects are removed during conversion.
•
Revisions marks, annotations, and comments
Revision marks are visible but cannot be changed. Annotations
and documents are removed during conversion.
MARS-1030 User Manual
144
5.2.7
Remote Connection
Using Remote Desktop Connection, you can log on to Windows Terminal
Server and use all programs installed on this server. For example, instead
of running Microsoft Pocket Word, you can run the desktop version of
Microsoft Word.
5.2.7.1 Connecting to Terminal Server
Select Start > Programs
> Remote Connection, or
run ‘CETSC’ from the
command prompt.
In the Server box, type or
select a Terminal Server
name or TCP/IP address,
or select a server in the
drop-down list.
Select Connect.
In the Remote Connection window, type your
user name, password, and
domain(if required), and
then select OK.
Figure 5.4: Remote Connected
5.2.7.2 Disconnecting Without Ending a Session
In the Remote Connection window, select Start > Shutdown.
Select Disconnect > OK.
Note: If you previously disconnected from a Terminal Server without
ending the session, the Terminal Server will continue to execute
any running processes and Remote Connection can later reconnect
to this same session(if your administrator has configured Remote
Connection to reconnect to disconnected sessions).
5.2.7.3 Disconnecting and Ending a Session
In the Remote Connection window, select Start > Shutdown.
Select Log Off > OK.
145
Chapter 5
5.2.8
Windows Explorer
Windows Explorer works almost the
same on your PDT as it does on your
PC. See the topics below for information
about the difference in Windows
Explorer on your device.
Figure 5.5: Windows Explorer
5.2.8.1 Navigating in File View
Go forwards and Back
– To go to the previous folder, select Go > Back.
– To go to the next folder (which you have just viewed), select
Go > Forward.
Use the Go menu
– To quickly access the My Documents folder, select Go > My
Documents
– To see all of the folders you have accessed, select Go > History. Double-tap a folder to return to it.
5.2.8.2 Viewing Files as Icons Lists
To view icons, select View > Large Icons or Small Icons.
To view a list, select View > Details.
5.2.8.3 Working with Files and Folders
Create a new folder
– If necessary, open the folder where you want the new folder to
reside.
MARS-1030 User Manual
146
*
– Select File > New Folder.
Add a folder to your Favorites list
– Open the folder
– Select Favorites > Add to Favorites.
– In the Name box, type the shortcut name.
Tips:
•
•
To open a favorite file or folder, select Favorites and then select
the folder.
To organize your favorites, select Favorites > Organize Favorites.
Transfer a file using infrared
– To send a file, select it, line up the infrared ports, and select File
> Send To > Infrared Recipient.
– To receive a file, line up the infrared ports, and select File >
Receive.
5.2.8.4 Creating Desktop Shortcuts
Display the file or Web page for which you want to create a Shortcut.
Select File > Send to.
Select Desktop as Shortcut.
5.2.8.5 Switch to Internet
Type a URL in the Address bar.
147
Chapter 5
5.3 DiskOnChip
The DiskOnChip let the application or a data file can be stored into the
Flash Memory.
Note: The DiskOnChip storage memory persists all reset (warm/cold
reboot) conditions and software/firmware updates.
We strongly recommends installing all applications, applets, programs,
and important data files to the DiskOnChip Flash location.
Caution:
If an application or a data file is only installed or saved in RAM, a
hard reset will result in the loss of that application or data file.
5.3.1
Saving to Flash
To save an application or data to the Flash Memory, from your current
application, select File > Save As > navigate to the DiskOnChip location
and save it.
5.3.2
DiskOnChip Location
To access the contents of DiskOnChip storage:
Double-tap the My Computer icon on the desltop.
Double-tap the DiskOnChip icon to view DiskOnChip.
Figure 5.6: DiskOnChip
MARS-1030 User Manual
148
5.3.3
DiskOnChip Size
The size of the DiskOnChip will vary,
depending on the size of system
firmware.
Inside the DiskOnChip
directory, tap File > Properties.
The DiskOnChip Properties
dialog:
The number following Free is the
amount of memory currently available on your device.
Figure 5.7: DiskOnChip Size
149
Chapter 5
MARS-1030 User Manual
150
APPENDIX
Barcode Setting
A.1 Setup Tab
Function Explaining:
Item
Symbology
Setup
Decoder Setup
Options
MARS-1030 User Manual
Function Explaining
Selecting the Symbology Setup menu item causes the
symbology setup dialog to be displayed. This dialog
consists of a symbology drop down list, plus four
buttons and a message box.
Selecting the decode menu item displays the decode
options dialog box.
Selecting the Options Menu item displays the Setup
dialog box
152
Item
Save Current
Config to File
Restore Config
From File
Exit
Function Explaining
The application has the ability to save the Config file.
The Config file that is saved when this item is selected
depends on the Config that is active. You will be
presented with a "Rea ..." dialog where you are asked
to select the name of the file to save. The default file
extension matches the current active Config. Saving a
Config file this way is independent from the Config
Format option of the Imager menu. In this case, the
Config file is saved as it appears on the screen instead
of how it was received.
This selection restores the Config from any file. The
Config file is full size, uncompressed, and
unprocessed.
Selecting Exit shuts down the Application Program.
153
Chapter A
A.1.1
Symbology Setup
Selecting the Symbology Setup menu item causes the symbology setup
dialog to be displayed. This dialog consists of a symbology drop down
list, plus four buttons and a message box.
Function Explaining:
Item
Function Explaining
Default Symbol
Causes the current symbology shown in the drop
down list to be set to internal defaults.
Default All
Symbologies
Defaults all symbology options for all symbologies to
internal defaults.
Enable All
Symbologies
Enables all symbologies, but does not change other
symbol options.
Disable All
Symbologies
Disables all symbologies without affecting other
symbol options.
MARS-1030 User Manual
154
A.1.2
Decoder Setup
Function Explaining:
Item
No Read
Timeout
Multiple
Symbols Mode
Function Explaining
Maximum time (in milliseconds) that the imager will
attempt to decode before declaring a “No Decode”
condition. If attempting to decode using the trigger key,
the imager quits decode attempts even if the trigger key
remains depressed. You will not be able to start a new
decode using the trigger until after the trigger is
released. The timeout also applies to the decode
operation of the imaging technology. The Timeout
range is 0 meaning no timeout (i.e., infinite) to 300,000.
Enables/Disables multiple symbols decoding. Normally
the imager stops attempting to decode when a bar
code symbol is decoded. In multiple symbols mode, the
imager will not stop until the trigger is released or a “No
Decode” timeout occurs. The same bar code will not
read again until current decoding stops.
155
Chapter A
Item
Function Explaining
Aimers During
Capture
Enables/Disables aimers during decoding.
Center Window A decoded symbol is returned only if it intersects a
Decode Enable rectangle specified by the center window.
Center Window indicates the percent-age of width and
height of the center decode rectangle, relative to the
Center Window
entire image. The limits are 0-100%. The defaults
are20x20 (128x96 pixels).
The Display Symbol Information option enables/
Display Symbol disables display of decoded symbol information, which
Information
includes the AIM ID, SymID (Code ID), and symbol
modifier.
Display No
Decode
Message
Enables/Disables display “No Decode” message if no
bar code symbol is decoded by either a timeout or trigger release.
MARS-1030 User Manual
156
A.1.3
Options
Function Explaining:
Item
Trigger Timeout
Termination
Code
Beep after data
collect
Function Explaining
Select the scanning timeout duration (in seconds) from
this pull-down list. <3 ~ 10 sec, Default: 6>
None
After showing barcode, do not action.
After showing the barcode, jump to next
CRLF
row.
Space
After showing the barcode, jump one unit.
Tab
After showing the barcode, jump a section.
Select the time of beep tone after data collect.
Disable
Auto Scan
Label
Disable this functionality.
Alternate second number of Continuous
1 ~5 sec
Scan.
Prefix
Type the desired label prefix in this text box
Suffix
Type the desired label suffix in this text box
157
Chapter A
A.2 Update Tab
MARS-1030 User Manual
158
Function Explaining:
Item
Function Explaining
When this item is selected, the imager is queried
for the current firmware version information. The
Firmware Revision
version information is then displayed in the text
window.
This item allows new engine firmware to be
installed into the imager. When Flash New
Firmware is selected; you are prompted to select
the firmware file. The file, which must have the
extension ".bin", must reside on the PDT. The
firmware file can be copied to the PDT using
Microsoft Explorer as long as the PDT is linked to
the PC via Microsoft's Active Sync. The default
search location is the My Documents folder. Once
you select a file, the file is transferred to the
Flash New Firmware
engine. The engine then writes the new firmware
into flash memory and re-initializes. The flashing
of the firmware and subsequent restart takes
approximately 30 seconds. The application
insures that the unit will not enter suspend mode
during that time.
Note: It is very important that the device remains
awake during this time. Failure to do so can
cause the scan engine to become unusable.
159
Chapter A
A.3 Symbologies List
A.3.1
Aztec
Function Explaining:
Item
Explaining
Symbol Enable
Enable Aztec Runes
Message Length
MARS-1030 User Manual
Enable this barcode
If you are scanning Aztec Runes, which are
the smallest type of Aztec Code symbol with
the ability to encode a very short license
plate message.
The minimum and maximum length ranges
for the barcode are 1-3750.
160
A.3.2
Codabar
Function Explaining:
Item
Explaining
Symbol Enable
Check Char/Digit
Enable
Check Char/Digit
Transmit
Start/Stop Transmit
Message Length
Enable this barcode
The scanner reads barcode data with a check
digit. If not checked, the bar code will be read
as though no check digit was present.
The scanner will only read Codabar bar codes
printed with a check digit, and will transmit
this character at the end of the scanned data.
This setting is only valid if check char/digit is
enabled.
Start/Stop characters identify the leading and
trailing ends of the barcode.
The minimum and maximum length ranges
for the barcode are 2-60.
161
Chapter A
A.3.3
Code 11
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode.
This option sets whether 1 or 2
check digits are required with Code
11 barcode.
The minimum and maximum length
ranges for the barcode are 1-80.
Check Char/Digit Enable
Message Length
Check Digits Required
Default = Two Check Digits.
MARS-1030 User Manual
162
A.3.4
Code 128
Function Explaining:
Item
Explaining
Symbol Enable
Message Length
Enable this barcode
The minimum and maximum length ranges for
the barcode are 0-80.
163
Chapter A
A.3.5
Code 39
Function Explaining:
Item
Explaining
Symbol Enable
Check Char/Digit
Enable
Check Char/Digit
Transmit
Start/Stop Transmit
MARS-1030 User Manual
Enable this barcode
The scanner reads barcode data with a
check digit. If not checked, the barcode will
be read as though no check digit was
present.
The scanner will only read Code 39 barcode
printed with a check digit, and will transmit
this character at the end of the scanned
data. This setting is only valid if check char/
digit is enabled.
Start/Stop characters identify the leading
and trailing ends of the barcode.
164
Item
Explaining
If this box is checked, the scanner can
Append Mode Enable append the data from several Code 39
barcode together before transmitting them
to the host computer. When this function is
enabled, the scanner stores those Code 39
barcode that start with a space (excluding
the start and stop symbols), and doesn’t
immediately transmit the data. The scanner
stores the data in the order in which the barcode are read, deleting the first space from
each. The scanner transmits the appended
data when it reads a Code 39 bar code that
starts with a character other than a space,
or when it reads a barcode that is not Code
39.
If Full ASCII Code 39 decoding is turned on,
Full ASCII Translation
certain character pairs within the barcode
symbol will be interpreted as a single c
haracter.
Message Length
The minimum and maximum length ranges
for the barcode are 0-48.
165
Chapter A
A.3.6
Code 49
Function Explaining:
Item
Explaining
Symbol Enable
Message Length
MARS-1030 User Manual
Enable this barcode
The minimum and maximum length ranges for the
barcode are 1-81.
166
A.3.7
Code 93
Function Explaining:
Item
Explaining
Symbol Enable
Message Length
Enable this barcode
The minimum and maximum length ranges for
the barcode are 0-80.
167
Chapter A
A.3.8
Composite Codes
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode.
Enable
Whether want to scanning UPC-A/EAN-13
Composite codes.
UPC-A/
EAN-13 Composite
Message Length
MARS-1030 User Manual
The minimum and maximum length ranges for
the barcode are 1-2435.
168
A.3.9
Data Matrix
Function Explaining:
Item
Explaining
Symbol Enable
Message Length
Enable this barcode
The minimum and maximum length ranges for
the barcode are 1-1500.
169
Chapter A
A.3.10 EAN-8
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
The output of the check digit at the end
of the scanned data.
Option allows decoding and outputting
of a 2 digits addendum on the end of all
Enable 2 Digit Addenda
scanned EAN-8 data.
Option allows decoding and outputting
of a 5 digits addendum on the end of all
Enable 5 Digit Addenda
scanned EAN-8 data.
Only reads EAN-8 barcodes that have
Addenda Required
addenda.
When this feature is selected, the data
is output with a space between the
Include Addenda Separator data from the main barcode and the
data from the addenda. When turned
off, there is no space.
Check Char/Digit Transmit
MARS-1030 User Manual
170
A.3.11 EAN-13
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
The output of the check digit at the end
of the scanned data.
Option allows decoding and outputting
of a 2 digits addendum on the end of
Enable 2 Digit Addenda
all scanned EAN-13 data.
Option allows decoding and outputting
of a 5 digits addendum on the end of
Enable 5 Digit Addenda
all scanned EAN-13 data.
Only reads EAN-13 barcodes that
Addenda Required
have addenda.
When this feature is selected, the data
is output with a space between the
Include Addenda Separator data from the main barcode and the
data from the addenda. When turned
off, there is no space.
Check Char/Digit Transmit
171
Chapter A
A.3.12 Interleaved 2 of 5
Function Explaining:
Item
Explaining
Symbol Enable
Check Char/Digit Enable
Check Char/Digit Transmit
Message Length
MARS-1030 User Manual
Enable this barcode
The scanner reads barcode data with
a check digit. If not checked, the
barcode will be read as though no
check digit was present.
The scanner will only read Interleaved
2 of 5 barcodes printed with a check
digit, and will transmit this character at
the end of the scanned data. This
setting is only valid if check char/digit
is enabled.
The minimum and maximum length
ranges for the barcode are 2-80.
172
A.3.13 MaxiCode
Function Explaining:
Item
Explaining
Symbol Enable
Message Length
Enable this barcode
The minimum and maximum length ranges for
the barcode are 1-150.
173
Chapter A
A.3.14 MicroPDF417
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
Message Length
The minimum and maximum length ranges for
the barcode are 1-366.
MARS-1030 User Manual
174
A.3.15 OCR-A, OCR-B, US Currency
Use this section to program the imager to read machine readable fonts
used in optical character recognition (OCR). The imager reads 6 to 60
point OCR typeface.
OCR Mode
•
OCR-A
•
OCR-B
175
Chapter A
•
U.S. Currency Serial Number (Money)
•
MICR E-13B
•
SEMI Font
You can either select an OCR default, or create your own custom template for the type of OCR format you intend to read. See "OCR Templates" if you want to create a custom “template” or character string that
defines the length and content of OCR strings that will be read with your
imager.
Note: Setting the template and check character options are essential for
OCR reading.
OCR Off turns off all OCR capability in the scanner, so the scanner will
be able to scan linear, stacked, matrix, and composite bar codes, but not
OCR fonts. In addition, any OCR templates you have created are erased.
The 8 digit default templates are reinstated for any future use of the OCRA, OCR-B, or U.S. Currency fonts.
If you select OCR-A, OCR-B, or U.S. Currency you can scan characters
in that font. The default setting allows you to scan any 8 digit combination. If you have created an OCR template, character combinations that fit
the template can be scanned (see Creating an OCR Template).
OCR Direction
The OCR Direction setting can be used to prevent misreads of character
strings that could be interpreted differently in different orientations when
MARS-1030 User Manual
176
you know the orientation of the characters that are being read in relation
to the imager (e.g., 80086996 could read as 80086996 or 96698008).
Default = Left-to-Right (LtoR)
OCR Templates
You can create a custom “template”, or character string that defines the
length and content of OCR strings that will be read with your imager.
There are several choices when creating a custom template for your application. You can create a template for a single format, you can string
together several formats, and you can create a template for a user-defined
variable. These choices are described in detail below.
Creating an OCR Template
A single template allows you to program the imager to read any combination of characters in the order you specify. Refer to examples that follow
the Template Characters table below.
Template Characters\
represents any alphanumeric character (digit or letter)
represents a check character position
represents any digit
represents any available OCR character
represents character from user-defined variable “g”
represents character from user-defined variable “h”
represents any uppercase letter
marks the start of a new template
multi row indicator
All other characters represent themselves. Spaces can be used.
Note: In MICR E13 B templates, TOAD characters (capital letters T, O, A,
and D), represent Transit, On Us, Amount, and Dash.
Note: OCR templates default to eight digits, no check character.
177
Chapter A
To Add an OCR Template
1.
Turn on the OCR font you want to read.
2.
Begin building the template.
Scan the Enter OCR Template symbol.
3.
Scan the characters for the string.
Use the Template Characters chart above to determine what characters
you need to create your format. Use the OCR Programming Chart (after
the Sample Codes in the back of this manual) to scan the characters for
your template.
Example: You need to read any combination of eight digits. The
template would be:
To create this template, you would enable the OCR-A font. Scan the
Enter OCR Template symbol, and then scan the d from the OCR Programming Chart in the back of this manual eight times. Scan Save OCR
Template. This would let you read any string of eight digits, for example:
Character Match Sequences
On the ASCII Conversion Chart (Code Page 1252), page A-4, find the
Hex value that represents the character(s) you want to match. Use the
Programming Chart (inside the back cover) to scan the numbers that represent these characters.
Example: You need to read three digits, three specific characters (ABC),
three digits. The template would be:
To create this template, you would enable the OCR-A font. Scan the
Enter OCR Template symbol. Scan the d from the OCR Programming
Chart in the back of this manual three times. Then scan 414243 from the
inside back cover (the hex characters for “A,” “B,” and “C”), and scan the
MARS-1030 User Manual
178
d three more times. Scan Save OCR Template. This would let you read
any string of three digits, “ABC,” then any string of three digits, for
example:
Adding Spaces
You may also need to put spaces in your template.
Example: You need to read three digits, space, three specific characters
(ABC), space, three digits. The template would be:
To create this template, you would enable the OCR-A font. Scan the
Enter OCR Template symbol. Scan the d from the OCR Programming
Chart in the back of this manual three times, and then scan 2041424320
from the Programming Chart on the inside back covers (the hex characters for “space,” “A,” “B,” “C,” “space”). Scan the d three more times,
and then scan Save OCR Template. This would let you read any string
of three digits, space, “ABC,” space, and then any string of three digits.
For example:
Note: If using Quick*View to program, use the space bar to designate a
space and not the hex value of 20.
4.
Exit OCR Template Editor
Scan Save OCR Template to save your entries. Discard OCR
Template exits without saving any OCR Template changes.
Stringing Together Multiple Formats (Creating “Or” Statements)
You may want to program the imager to accept many OCR formats. To
do this, you would string together each format with a “t.” This tells the
imager to read optical characters that match any one of the formats in the
template.
179
Chapter A
Example: You need to read any combination of eight digits, or a combination of four digits, two uppercase letters, and two digits. The template
would be:
To create this template, you would enable the OCR-A font. Scan the
Enter OCR Template symbol. Scan the d from the OCR Programming
Chart in the back of this manual eight times, then scan the t to create the
“or” statement. Then you would scan the characters for the second template. Scan d four times, scan l two times, then scan d two more times.
Scan Save OCR Template. This would let you read either type of format, for example:
You can string together as many templates as you need.
OCR Template Codes
Note: Reading more than three rows of OCR is not recommended.
Contact the factory if you have an application that requires reading four
or more rows of OCR.
† One or more two-digit numbers and Save are required after reading this
programming symbol. Refer to the Programming Chart on the inside the
back cover of this manual.
MARS-1030 User Manual
180
Exit Selections
181
Chapter A
ASCII Conversion Chart (Code Page 1252)
MARS-1030 User Manual
182
ASCII Conversion Chart (Code Page 1252)
183
Chapter A
OCR Programming Chart
MARS-1030 User Manual
184
Programming Chart
185
Chapter A
MARS-1030 User Manual
186
A.3.16 PDF417
Function Explaining:
Item
Explaining
Symbol Enable
Message Length
Enable this barcode
The minimum and maximum length ranges for the
barcode are 1-2750.
187
Chapter A
A.3.17 Postnet
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
Check Char/Digit Transmit
MARS-1030 User Manual
The scanner will only read US Postnet
bar codes printed with a check character, and will transmit this character
at the end of the scanned data.
188
A.3.18 QR Code
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
Message Length
The minimum and maximum length ranges for
the barcode are 1-3500.
189
Chapter A
A.3.19 Reduced Space Symbology
Function Explaining:
Item
Explaining
RSS Expanded Enable
Enable RSS Expanded code
RSS Limited Enable
Enable RSS Limited code
RSS 14 Enable
Enable RSS 14 code
Message Length
MARS-1030 User Manual
The minimum and maximum length
ranges for the barcode are 4-74.
190
A.3.20 UPC-A
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
The output of the check digit at the end
of the scanned data.
Option allows decoding and outputting
of a 2 digits addendum on the end of
Enable 2 Digit Addenda
all scanned UPC-A data.
Option allows decoding and outputting
of a 5 digits addendum on the end of
Enable 5 Digit Addenda
all scanned UPC-A data.
Only reads UPC-A barcodes that have
Addenda Required
addenda.
When this feature is selected, the data
is output with a space between the
Include Addenda Separator data from the main barcode and the
data from the addenda. When turned
off, there is no space.
If you want the numeric system digit of
Send Number System
a UPC symbol transmitted.
Check Char/Digit Transmit
191
Chapter A
A.3.21 UPC-E
Function Explaining:
Item
Explaining
Symbol Enable
Check Char/Digit Transmit
Enable 2 Digit Addenda
Enable Expanded UPC-E
Enable this barcode
The output of the check digit at the
end of the scanned data.
Option allows decoding and outputting
of a 2 digits addendum on the end of
all scanned UPC-E data.
Enable UPC-E Expanded code
Option allows decoding and outputting
of a 5 digits addendum on the end of
all scanned UPC-E data.
Only reads UPC-E barcodes that have
Addenda Required
addenda.
When this feature is selected, the data
is output with a space between the
Include Addenda Separator data from the main barcode and the
data from the addenda. When turned
off, there is no space.
If you want the numeric system digit of
Send Number System
a UPC-E symbol transmitted.
Enable 5 Digit Addenda
MARS-1030 User Manual
192
A.3.22 UPC-E1
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
The output of the check digit at the
end of the scanned data.
Option allows decoding and outputting of a 2 digits addendum on the
end of all scanned UPC-E1 data.
Check Char/Digit Transmit
Enable 2 Digit Addenda
Enable UPC-E Expanded code
Enable Expanded UPC-E
Enable 5 Digit Addenda
Addenda Required
Include Addenda Separator
Send Number System
Option allows decoding and outputting of a 5 digits addendum on the
end of all scanned UPC-E1 data.
Only reads UPC-E1 barcodes that
have addenda.
When this feature is selected, the
data is output with a space between
the data from the main barcode and
the data from the addenda. When
turned off, there is no space.
If you want the numeric system digit
of a UPC-E1 symbol transmitted.
193
Chapter A
A.3.23 ISBT
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
MARS-1030 User Manual
194
A.3.24 British Post
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
195
Chapter A
A.3.25 Canadian Post
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
MARS-1030 User Manual
196
A.3.26 Australian Post
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
Send Bar
Australian Post is a 4-state symbology that
was designed with a non-defined user area.
The user can define how that area field is
interpreted. Most systems have dedicated
decoders that don’t know how to decode a
symbology that is not defined. If you select
the Send Bar Width Data, the bar levels will
be outputted (0-3 for the four states) so that
the receiving device can then decode
appropriately.
Width Data
197
Chapter A
A.3.27 IATA 2 of 5
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
Message Length
The minimum and maximum length ranges for
the barcode are 1-48.
MARS-1030 User Manual
198
A.3.28 Codablock F
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
Message Length
The minimum and maximum length ranges for
the barcode are 1-2048.
199
Chapter A
A.3.29 Japanese Post
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
MARS-1030 User Manual
200
A.3.30 Planet Code
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
Check Char/Digit Transmit
The scanner will only read Planet barcodes printed with a check character,
and will transmit this character at the
end of the scanned data.
201
Chapter A
A.3.31 KIX (Netherlands) Post
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
MARS-1030 User Manual
202
A.3.32 MSI
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
Check Char/Digit Transmit
Message Length
The scanner will only read MSI barcodes printed with a check character,
and will transmit this character at the
end of the scanned data.
The minimum and maximum length
ranges for the barcode are 4-48.
203
Chapter A
A.3.33 TCIF Linked Code 39
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
MARS-1030 User Manual
204
A.3.34 Mayrix 2 of 5
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
Message Length
The minimum and maximum length ranges for the
barcode are 1-80.
205
Chapter A
A.3.35 Korean Post
Function Explaining:
Item
Explaining
Symbol Enable
Enable this barcode
Message Length
The minimum and maximum length ranges for
the barcode are 2-80.
MARS-1030 User Manual
206

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-702
About                           : uuid:aed15e06-544f-4d81-bc56-388e7159f229
Producer                        : Acrobat Distiller 6.0 (Windows)
Creator Tool                    : FrameMaker 7.0
Modify Date                     : 2006:10:30 10:58:41-08:00
Create Date                     : 2006:09:26 11:28:18Z
Metadata Date                   : 2006:10:30 10:58:41-08:00
Document ID                     : uuid:b79982be-9c43-46fe-9fea-ae1011f7b208
Instance ID                     : uuid:8921ed63-ddc2-4246-bbce-5913773003ab
Format                          : application/pdf
Title                           : Mars-1030 Book.book
Creator                         : Fandi
Page Count                      : 212
Author                          : Fandi

EXIF Metadata provided by EXIF.tools

Advantech Co MARS-1030 Portable Data Terminal User Manual Mars 1030 Book

Advantech Co Ltd Portable Data Terminal Mars 1030 Book

Manual

FCC ID Filing: M82-MARS-1030

Navigation menu

Namespaces

Views

Navigation