Advantech Co MITW101 Computer User Manual MIT W101 0215
Advantech Co Ltd Computer MIT W101 0215
User manual
FCCID:M82ͲMITW101
1
Computer
MIT-W101
User Manual
Ver 0.1
MIT-W101 User Manual
FCCID:M82ͲMITW101
2
Copyright
The documentation and the software included with this product are copyrighted
2014 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves
the right to make improvements in the products described in this manual at any time
without notice. No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written permission of
Advantech Co., Ltd. Information provided in this manual is intended to be accurate
and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor
for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
All other product names or trademarks are properties of their respective owners.
FCCID:M82ͲMITW101
3
Declaration of Conformity
CE Conformity Statement
Radio products with the CE alert marking comply with the R&TTE Directive
(1999/5/EC) issued by the Commission of the European Community. Compliance
with this directive implies conformity to the following European Norms (in brackets
are the equivalent international standards).
• EN 60950-1 (IEC60950-1) - Product Safety
• EN 300 328 Technical requirement for radio equipment
•EN 301 893 Technical requirement for radio equipment
• EN 301 489 General EMC requirements for radio equipment
Products that contain the radio transmitter are labeled with CE alert marking and
may also carry the CE logo.
MIT-W101 User Manual
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference;
2. This device must accept any interference received, including interference that
may cause undesired operation.
FCC RF Radiation
Exposure Statement:
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of
20 centimeters between the radiator and your body.
The device is designed to meet the requirements for exposure to radio waves established by the Federal
Communications Commission (U.S.A.).
These requirements set a SAR limit of 1.24 W/kg, averaged over one gram of tissue.
The FCC highest SAR values reported under this standard during Product certification for use at the head are 1.02 W
/
kg, and when properly worn on the body is 10.1W/kg.
The device is designed to meet the requirements for exposure to radio waves established by the Federal
Communications Commission (U.S.A.).
The FCC highest SAR values reported under this standard during Product certification for use at the head are
13.5 W/kg, and when properly worn on the body is 13.1 W/kg.
The device is designed to meet the requirements for exposure to radio waves
established by the Federal Communications Commission (U.S.A.).
These requirements set a SAR limit of 1.6W/kg, averaged over one gram of tissue.
The FCC highest SAR values reported under this standard during Product certification
for use at the body is 0.886 W/kg.
7KHGHYLFHLVGHVLJQHGWRPHHWWKHUHTXLUHPHQWV
I
RUH[SRVXUHWRUDGLRZDYHVHVWDEOLVKHGE\WKH)HGHUDO
&RPPXQLFDWLRQV&RPPLVVLRQ86$
7KHVHUHTXLUHPHQWVVHWD6$5OLPLWRI:NJDYHUDJHGRYHURQHJUDPRIWLVVXH
7KH)&&KLJKHVW6$5YDOXHVUHSRUWHGXQGHUWKLVVWDQGDUGGXULQJ3URGXFWFHUWLILFDWLRQIRUXVHDWWKHERG\
LV:NJ
FCCID:M82ͲMITW101
4
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try and correct the interference by one or more of the following
measures:
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
• Consult the dealer or an experienced computer technician for help
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
Technical Support and Assistance
1. Visit the Advantech website at http://support.advantech.com where you can find
Caution! Exposure to Radio Frequency Radiation.
The radiated output of this device is far below the FCC radio frequency exposure
limits. Nevertheless, the device shall be used in such a manner that the potential
for human contact during normal operation is minimized.
When connecting an external antenna to the device, the antenna shall be placed in
such a manner to minimize the potential for human contact during normal
operation. In order to avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna shall not be less than 20cm
(8inches) during normal operation.
MIT-W101 User Manual I the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
FCCID:M82ͲMITW101
5
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this user manual for later reference.
3. Disconnect this equipment from AC outlet before cleaning. Do not use liquid or
spray detergents for cleaning.
4. Keep this equipment away from humidity.
5. Put this equipment on a reliable surface during installation. Dropping it or
letting it fall could cause damage.
6. Do not leave this equipment in an environment unconditioned where the
storage temperature under -20qC or above 60qC, it may damage the
equipment.
7. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
8. Place the power cord such a way that people cannot step on it. Do not place
anything over the power cord. The voltage and current rating of the cord
should be greater than the voltage and current rating marked on the product.
9. All cautions and warnings on the equipment should be noted.
10. If the equipment is not used for long time, disconnect it from the power
source to avoid being damaged by transient over-voltage.
11. Never pour any liquid into ventilation openings. This could cause fire or
electrical shock.
12. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
13. If any of the following situations arises, get the equipment checked by service
personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well or you cannot get it to work according to
user manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
14. CAUTION: The computer is provided with a battery-powered real-time clock
circuit. There is a danger of explosion if battery is incorrectly replaced.
Replace only with same or equivalent type recommended by the manufacture.
Discard used batteries according to the manufacturer’s instructions.
FCCID:M82ͲMITW101
6
Battery Safety
RTC Battery Caution
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
ΓDo not place the battery incorrectly as this may cause danger of explosion.
ΓDispose of used batteries according to the manufacturer's instructions.
ΓDo not dispose of batteries in a fire. They may explode. Check with local
authorities for disposal instructions.
Battery Pack Caution
ΓThe battery used in this device may present a risk of fire or chemical burn if
mistreated. Do not disassemble, heat above 40°C, or incinerate. Replace standard
battery pack with UF703450F Li-ion 11.1V 2860mAh SANYO. Use of another battery
may present a risk of fire or explosion.
ΓDispose of used batteries according to local disposal regulations. Keep away from
children. Do not disassemble and do not dispose of in a fire.
Battery Charge Notice
It is important to consider the environment temperature whenever you are charging
the Lithium-Ion battery pack. The process is more efficient at normal room
temperature or slightly cooler. It is essential that you charge batteries within the
stated range of 0°C to 40°C. Charging batteries outside of the specified range could
damage the batteries and shorten their charging life cycle.
Storage and Safety Notice
Although charge Lithium-Ion batteries may be left unused for several months, their
capacity may be depleted due to the buildup of internal resistance. If this happens
they will require recharging prior to use. Lithium-Ion batteries may be stored at
temperatures between -20°C to 60°C, however they may be depleted more rapidly
at the high end of this range. It is recommended to store batteries within normal
room temperature ranges.MIT-W101 User Manual
1
FCCID:M82ͲMITW101
7
Chapter 1 Ready to Go...............................................................................................9
1.1 Symbols Used in this Manual ...................................................................................... 9
1.2 Product Features........................................................................................................ 10
1.3 Package Contents ...................................................................................................... 10
1.4 Optional Accessories ................................................................................................. 10
1.5 Optional Modules ....................................................................................................... 11
1.6 Exploring the MIT-W101............................................................................................ 11
1.6.1 Front View............................................................................ 11
1.6.2 Rear View............................................................................. 12
1.6.3 Right View ............................................................................ 13
1.6.4 Left View ............................................................................. 13
1.6.6 Bottom View ......................................................................... 14
Chapter 2 Getting Started .......................................................................................15
2.1 Installing the Rubber Bumpers (Optional) ............................................................. 16
2.2 Removing the Rubber Bumpers (optional)............................................................. 17
2.3 Installing an Expansion module (Optional)............................................................ 18
Chapter 3 Making Connections................................................................................19
3.1 Connecting the Power............................................................................................... 20
3.2 Connecting to a Monitor ........................................................................................... 20
3.3 Connecting USB Devices............................................................................................ 21
3.4 Connecting Headphones ........................................................................................... 21
3.5 Connecting a Microphone ......................................................................................... 21
Chapter 4 Turning On ...............................................................................................23
4.1 Controlling the MIT-W101......................................................................................... 24
4.1.1 Using the Touch Screen......................................................................................... 24
4.1.2 Using the Tap Function............................................................. 24
4.1.3 Using the Control Panel Buttons .................................................. 24
4.1.4 Using the On-Screen Keyboard .................................................... 25
FCCID:M82ͲMITW101
8
4.1.5 Adjusting Screen Brightness ....................................................... 27
4.1.6 Adjusting the Volume............................................................... 28
Chapter 5 Wireless Connections.............................................................................32
5.1 Wi-Fi Connection........................................................................................................ 33
5.2 Bluetooth Connections.............................................................................................. 36
5.2.1 Setting Up Bluetooth ............................................................... 36
Chapter 6 Advance Setting ......................................................................................39
6.1 Checking Battery Status............................................................................................ 40
6.2 Maintenance................................................................................................................ 40
6.2.1 Maintaining the Battery ............................................................ 40
6.2.2 Maintaining the LCD Display ....................................................... 41
6.2.3 Cleaning the MIT-W101 ............................................................. 41
Appendix Specifications...........................................................................................42
A.1 Specifications ............................................................................................................. 43
A.2 Optional Accessories ................................................................................................. 45
A.2.1 External Battery..................................................................... 45
A.2.2 Expansion Module ................................................................... 47
A.3 Installing an SSD and a SIM....................................................................................... 48
A.3.1.1 Inserting an SSD ................................................................... 48
A.3.1.2 Removing an SSD.................................................................. 50
FCCID:M82ͲMITW101
9
Chapter 1 Ready to Go
Congratulations on your purchase of the MIT-W101 Rugged Tablet PC. This product
combines rugged design with reliable performance and powerful functionality to
best suit all your needs, in a wide range of working conditions. This user manual
outlines all you need to know to set up and use your MIT-W101. If you have any
further questions or queries, contact our technical support team via our website:
http://www.advantech.com.tw/
1.1 Symbols Used in this Manual
Denotes information that must be observed.
Failure to do so may result in personal harm or damage to
the product.
FCCID:M82ͲMITW101
10
Denotes information that must be observed.
Failure to do so may result in personal harm or damage to
the product.
1.2 Product Features
• Rugged design.
• Featuring with the Future Intel® Celeron ™ processor for intelligent system.
• Built-in WLAN/Bluetooth/NFC.
• Durable, shock-resistant magnesium alloy housing.
• Comply with IP65 sealing & built to withstand a 4 ft drop with only 20 mm in
thickness.
• 10.1 “ WXGA TFT LCD
• Integrated Barcode, NFC and expansion module option of MSR and smart card
Reader.
• Optional accessory to meet 6ft drop and variety of user scenario.
1.3 Package Contents
Ensure all the following items are present when you receive your MIT-W101. If any of
these items are missing, contact your vendor immediately.
Screens used in this manual are for illustrative purposes
only. Actual screens may vary depending on your product
version.
• MIT-W101 Tablet PC
• AC power adaptor
• Battery Pack
1.4 Optional Accessories
• Docking station
• 3-in-1 VESA/ Hand strap / Kickstand Multiple function back cover
• Shoulder strap
• Rubber bumpers
• Capacitive stylus pen
FCCID:M82ͲMITW101
11
1.5 Optional Modules
• Barcode Scanner
• Expansion module (MSR and Smart Card Reader)
1.6 Exploring the MIT-W101
1.6.1 Front View
No. Component
1 P1 – Programmable Button
2 P2 - Programmable Button
3 Front Camera
4 Power button
5 Connected to expansion module
6 AC-in jack
7 Docking connector
FCCID:M82ͲMITW101
12
8 Projective capacitive multiple touch screen
9 I/O ports
• USB 3.0 x 1
• USB 2.0 x 1
• Micro HDMI x 1
• Audio x 1
10 Connectivity LED indicator
• Blue: when Wi-Fi / BT module is on
11 HDD LED indicator
• Blinking green: when hard disk drive is working
12 Power / Battery LED indicator
• Green: Battery is fully charged (>95%)
• Amber : Battery is charging
• Amber: Battery life is lower than 10%
1.6.2 Rear View
No. Component
FCCID:M82ͲMITW101
13
1 Back camera
2 Barcode scanner
3 SSD cover
4 Speaker
5 Battery
6 Battery Latch
7 NFC
1.6.3 Right View
No. Component
1 Connected pin for expansion module
1.6.4 Left View
FCCID:M82ͲMITW101
14
No. Component
1 I/O ports cover
2 Audio Jack
3 USB 3.0
4 USB 2.0
5 Micro HDMI
1.6.5 Top View
No. Component
1 Function buttons
2 Built-in MIC
3 Power button
1.6.6 Bottom View
No. Component
1 Docking connector
2 AC-in jack
L
FCCID:M82ͲMITW101
15
Chapter 2 Getting Started
FCCID:M82ͲMITW101
16
2.1 Installing the Rubber Bumpers (Optional)
To protect the housing case of MIT-W101, install the rubber bumpers.
1. Install the rubber bumpers on the left and right side of the MIT-W101.
2. Make sure the rubber bumpers are aligned and locked on the indents.
3. Screw the rubber bumpers on left and right properly into the MIT-W101.
The Rubber bumper could provide well drop protection
when device fall from high place. Please assure the
rubber was put on the right position and the screws was
fastened when install the bumper on device.
FCCID:M82ͲMITW101
17
2.2 Removing the Rubber Bumpers (optional)
1. Unscrew the rubber bumpers from the rear of the tablet PC.
2. Remove the rubber bumpers on the left and right.
FCCID:M82ͲMITW101
18
2.3 Installing an Expansion module (Optional)
1. Make sure the system is turned off.
2. Attach the expansion module connector to the MIT-W101.
3. Screw to secure the expansion module onto the MIT-W101.MIT-M
Please assure the expansion module was put on the right
position and the screws was fastened when install the
module on device. The expansion module might not work
if the device was not installed probably or damage by
drop.
FCCID:M82ͲMITW101
19
Chapter 3 Making Connections
FCCID:M82ͲMITW101
20
3.1 Connecting the Power
Before you can use your MIT-W101, you must fully charge the battery. Connect the
power adapter as shown and leave to charge for:
• A minimum of 2 hours when using the internal battery
• A minimum of 4 hours when a second battery is installed
Condition: the operation time is based on the LCD backlight at 50% and the average
utilization of the system under 10%.
3.2 Connecting to a Monitor
You can connect the MIT-W101 to an external monitor for enhanced viewing.
Connect one end of a HDMI to VGA cable to the Micro HDMI port on the left side of
the MIT-W101.Connect the other end to the VGA cable and connect to the monitor.
FCCID:M82ͲMITW101
21
3.3 Connecting USB Devices
You can connect peripheral devices, such as a USB keyboard and mouse, as well as
other wireless devices using the USB ports on the left side of the MIT-W101.
3.4 Connecting Headphones
You can connect a pair of headphones using the headphone jack on the left side of
the MIT-W101.
3.5 Connecting a Microphone
The MIT-W101 features a built-in microphone, but you can still connect an external
microphone if needed. Connect the microphone to the microphone jack on the left
side of the MIT-W101 as shown.
FCCID:M82ͲMITW101
22
FCCID:M82ͲMITW101
23
Chapter 4 Turning On
FCCID:M82ͲMITW101
24
1. Press and hold the power button to turn on the MIT-W101.
4.1 Controlling the MIT-W101
4.1.1 Using the Touch Screen
The MIT-W101 is equipped with touch screen technology, for ease of use when you
are on the go. Simply tap the screen with your finger to select icons and run
applications.
4.1.2 Using the Tap Function
When you tap on the screen with a pen or stylus, it emulates click functions of a
regular mouse.
• To emulate a left click single tap the screen once.
• To emulate a right click tap and hold the screen.
• To emulate a double click, tap the screen twice.
4.1.3 Using the Control Panel Buttons
The control panel buttons are located on the top side of MIT-W101.
See below for a description of the two buttons and its function.
Button Name Function
Function Press to access your favorite programs
Power Press to power on/off
FCCID:M82ͲMITW101
25
4.1.4 Using the On-Screen Keyboard
1. Click on icon in the taskbar to bring up the on-screen keyboard.
2.Use your finger or stylus pen to tap and enter letters, numbers and symbols as you
would with a regular keyboard. To type capital letters tap the lock icon on the
on-screen keyboard.
3. To use handwriting, tap bottom right button of On-Screen
Keyboard.
FCCID:M82ͲMITW101
26
4. Select the handwriting icon.
5. Use your finger and stylus pen to write on screen.
FCCID:M82ͲMITW101
27
4.1.5 Adjusting Screen Brightness
1. Tap the Settings icon on the right.
2.Tap Screen icon to access the brightness control.
FCCID:M82ͲMITW101
28
3. To move the brightness control bar up / down to increase / decrease brightness.
4.1.6 Adjusting the Volume
1. Tap the Settings icon on the right.
FCCID:M82ͲMITW101
29
2.Tap the Volume icon on the system tray.
1. Move the slide to adjust volume.
FCCID:M82ͲMITW101
30
2. Tap icon to mute.
FCCID:M82ͲMITW101
31
FCCID:M82ͲMITW101
32
Chapter 5 Wireless Connections
FCCID:M82ͲMITW101
33
5.1 Wi-Fi Connection
Wi-Fi access requires a separate purchase of a service
contract with a wireless service provider. Contact a
wireless service provider for more information.
The MIT-W101 comes pre-loaded with WLAN module; you can send and receive
signals to a Wi-Fi network then synchronize files.
A wireless network can be added either when the network is detected or by
manually entering settings information. Before doing these steps, determine if
authentication information is needed.
1. Tap the Settings icon on the right.
FCCID:M82ͲMITW101
34
2. Click the wireless connection icon in the notification area.
3. Select one of the wireless connections and click Connect.
4. You are prompted to enter a Security key for secure access. Contact the network
administrator for this key.
FCCID:M82ͲMITW101
35
5. Enter the required Security key and then tap Next to connect.
6. The wireless connection is negotiated.
The wireless connection icon in the notification area shows a connected status
whenever a wireless connection is present.
FCCID:M82ͲMITW101
36
Set
airplane mode or turn off wireless devices
5.2 Bluetooth Connections
The MIT-W101 comes with built-in Bluetooth functionality that allows you to connect
and communicate with other Bluetooth-enabled devices.
5.2.1 Setting Up Bluetooth
Follow these instructions to set up a Bluetooth connection.
1. Type Bluetooth in Search
2. In notification area, tap Add Bluetooth device.
FCCID:M82ͲMITW101
37
3. Add more Bluetooth device by clicking on Add a device.
4. Select Yes for comparing both MIT-W101 and the Bluetooth device after passkey is
confirmed.
FCCID:M82ͲMITW101
38
5. The Bluetooth device is successfully added into MIT-W101 when the process is
complete.
It is recommended that you use a passkey to prevent
unauthorized access to your MIT-W101.
FCCID:M82ͲMITW101
39
Chapter 6 Advance Setting
FCCID:M82ͲMITW101
40
6.1 Checking Battery Status
As it is likely you will be using your MIT-W101 when out and about, it is important
that you monitor the battery status regularly, to ensure you do not run out of power
at a critical moment.
1. Tap on the Power icon on the system tray to view detailed information and the
battery screen appears.
Balanced – Automatically balanced performance with energy consumption.
Power saver – Saves energy by reducing MIT-W101’s performance.
6.2 Maintenance
6.2.1 Maintaining the Battery
• Do not expose heat or attempt to disassemble the battery, and do not place the
battery in water or in a fire.
• Do not subject the battery to strong impact, such as a blow from a hammer, or
stepping on or dropping it.
• Do not puncture or disassemble the battery.
• Do not attempt to open or service the battery.
• Replace only with batteries designed specifically for this product.
• Keep the battery out of reach of children.
• Dispose of used batteries according to local regulations.
FCCID:M82ͲMITW101
41
6.2.2 Maintaining the LCD Display
• Do not scratch the surface of the screen with any hard objects.
• Do not spray liquid directly on the screen or allow excess liquid to drip down inside
the device.
• Do not place anything, such as food and drink, on the screen at any time to prevent
damage to the screen.
• Clean the LCD display only with a soft cloth dampened with denatured alcohol or a
proprietary LCD screen cleaner.
6.2.3 Cleaning the MIT-W101
1. Turn off the MIT-W101 and unplug the power cord.
2. Wipe the screen and exterior with a soft, damp cloth moistened only with water.
Do not use liquid or aerosol cleaners on the screen, as these will discolor the finish
and damage the screen.
MIT-W101 User Manual
FCCID:M82ͲMITW101
42
Appendix Specifications
FCCID:M82ͲMITW101
43
A.1 Specifications
Feature Description
Operating System
Microsoft Windows Embedded 8 Standard
Microsoft Windows 7 Professional for Embedded System
(Optional)
Processor Intel® Celeron® Processor N2930
Max. speed Quad Core 1.83GHz
Chipset Intel® Bay Trail-M SoC
Memory One DDR3L 1333MHz SO-DIMM, up to 8GB
Storage One mSATA SSD, up to 128GB
Display 10.1” WXGA TFT LCD
Touch Panel P-CAP Multiple Touch
Application Button
One Power button
Two Function programmable buttons for quick
selection of applications
Communication 802.11a/b/g/n WLAN built-in with integrated antenna
Bluetooth class 2, 4.0 + EDR built-in with integrated antenna
Camera 2.0M Fixed Focus Camera at front
5.0M Auto Focus Camera with Flash LED at rear
Main Battery Rechargeable Li-ion battery,
Standard battery, 11.1V, 2860 mAh, 3S2P
ITE Power Adapter
AC Adapter: AC 100V-240V 50/60Hz,1.5A
Output : 19Vdc/3.42~4.2A/65W, Auto Sensing/Switching
worldwide power supply
FCCID:M82ͲMITW101
44
Feature Description
Security 1. Password security
I/O Ports
One USB 3.0/ 2.0
One USB 2.0
One HP/MIC combined jack
One Micro HDMI type D
One DC-in jack
One Expansion port 8-pin
One Docking port 32-pin
Audio Output One 1 watt speaker
Expansion Port One MSR (On optional expansion module)
One Smart Card Reader (On optional expansion module)
Physical 295 x 196 x 20mm
Approx. 1.1Kg (base configuration); approx. 2.43lbs
Environment
Operating Temperature:
0ºC to 40ºC (Condition: Charge)
- 20ºC to 60ºC (Condition: discharge)
Storage Temperature -20ºC to 60ºC
Operating Humidity 5% ~ 95% @40C non-condensing
IP65 Compliant
4ft drop onto concrete
Feature Description
Certification FCC Class B, CE, CB, UL
Optional
Device /
Accessories
One Expansion module
FCCID:M82ͲMITW101
45
LED Status
DUT
on/off
AC
adapter
in
Internal
Battery
Green
LED
Amber
LED
Remark
Off X X Off Off System Off
Off V V Off On
Battery is charging
Off V V On Off
Battery is fully charged
(100%)
On V V Off On Battery is charging
On V V On Off
Battery is fully charged
(100%)
On V V Off On
Battery Low
(< 10 %)
A.2 Optional Accessories
A.2.1 External Battery
You can use an external battery to extend the power of your MIT-W101.
Battery specification: 2860 mAh, 11.1V
FCCID:M82ͲMITW101
46
A.2.1.2 Installing the External Battery
1. Align and insert the battery on the MIT-W101.
2. Lock to secure the battery once it is properly to be inserted.
A.2.1.2 Removing the External Battery
Repeat the above steps in reverse order to remove the battery.
FCCID:M82ͲMITW101
47
A.2.2 Expansion Module
Built-in MSR and Smart Card Reader in expansion module.
No. Function
1 MSR
2 Smart Card Reader
FCCID:M82ͲMITW101
48
A.3 Installing an SSD and a SIM
A.3.1.1 Inserting an SSD
You can insert an SDD to store data, which needs to be later transferred to another
machine, or to simply expand the storage capacity of the MIT-W101.
1. Open the SSD card compartment cover.
2. Insert the SDD, facing upwards, until it clicks into place.
FCCID:M82ͲMITW101
49
3. Screw and fix SSD.
4. Close the SDD compartment cover.
FCCID:M82ͲMITW101
50
A.3.1.2 Removing an SSD
1. Open the SSD compartment cover.
2. Unscrew and remove SSD from the slot.
FCCID:M82ͲMITW101
51
3. Close and screw the SSD card compartment cover.