Advantech Co TREK-72X-HB COMPUTER User Manual V4 12 EV User Manual
Advantech Co Ltd COMPUTER V4 12 EV User Manual
Contents
- 1. USERS MANUAL
- 2. User Manual
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1882489 |
| Application ID | +Lyk4QUS0atnaHNC+k7CCQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 171.3kB (2141282 bits) |
| Date Submitted | 2013-01-18 00:00:00 |
| Date Available | 2013-07-17 00:00:00 |
| Creation Date | 2017-10-28 17:22:43 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-10-28 17:22:43 |
| Document Title | Template_V4.12_EV_User_Manual |
| Document Creator | FrameMaker 10.0.2 |
| Document Author: | chunxia.zhao |
User Manual TREK-722/723 RISC All-In-One Mobile Data Terminal Copyright The documentation and the software included with this product are copyrighted 2012 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use. Acknowledgements TI and AM37x are trademarks of Texas Instruments.. Microsoft Windows is registered trademarks of Microsoft Corp. All other product names or trademarks are properties of their respective owners. Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events. Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For outof-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. Please consult your dealer for more details. If you think you have a defective product, follow these steps: 1. Collect all the information about the problem encountered. (For example, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem occurs. 2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available. 3. If your product is diagnosed as defective, obtain an RMA (return merchandize authorization) number from your dealer. This allows us to process your return more quickly. 4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service. 5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer. TREK-722/723 User Manual Part No. Edition 1 Printed in Taiwan December 2012 ii Declaration of Conformity CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure. In order to protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products. FCC Class B Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference may cause undesired operation. RF Exposure Information This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. iii TREK-722/723 User Manual Technical Support and Assistance 1. 2. Visit the Advantech web site at http://support.advantech.com where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call: – Product name and serial number – Description of your peripheral attachments – Description of your software (operating system, version, application software, etc.) – A complete description of the problem – The exact wording of any error messages Warnings, Cautions and Notes Warning! Warnings indicate conditions, which if not observed, can cause personal injury! Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g. There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. Note! Notes provide optional additional information. Document Feedback To assist us in making improvements to this manual, we would welcome comments and constructive criticism. Please send all such - in writing to: support@advantech.com Packing List Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately. TREK-722/ TREK-723 Mobile Data Terminal Warranty Card "Drivers, utilities, and user manual" CD-ROM End User License Agreement (WinCE), please download driver and relative document from http://support.advantech.com TREK-722/723 User Manual iv Power Cable TREK-722/723 User Manual Ordering Information Part Number Description TREK-722R-A0E TREK-722 barebone TREK-722R-CBCEA0E TREK-722R-A0E w/ GPS, CDMA, BT, CE TREK-722R-GBCEA0E TREK-722R-A0E w/ GPS, GPRS, BT, CE TREK-722R-HBCEA0E TREK-722R-A0E w/ GPS, HSPA, BT, CE TREK-723R-A0E TREK-723 barebone TREK-723R-CBCEA0E TREK-723R-A0E w/ GPS, CDMA, BT, CE TREK-723R-GBCEA0E TREK-723R-A0E w/ GPS, GPRS, BT, CE TREK-723R-HBCEA0E TREK-723R-A0E w/ GPS, HSPA, BT, CE Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. Keep this equipment away from humidity. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage. Do not leave this equipment in an environment unconditioned where the storage temperature under -30° C (-22° F) or above 70° C (158° F), it may damage the equipment. Do not operate this equipment in an environment temperature may over 70° C (158° F). The surface temperature of metal chassis may be scorch and hot. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. Position the power cord so that people cannot step on it. Do not place anything over the power cord.The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. All cautions and warnings on the equipment should be noted. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. If one of the following situations arises, get the equipment checked by service personnel: The power cord or plug is damaged. Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment does not work well, or you cannot get it to work according to the user's manual. The equipment has been dropped and damaged. The equipment has obvious signs of breakage. TREK-722/723 User Manual vi 15. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 16. CAUTION: Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. 17. CAUTION: Always ground yourself to remove any static charge before touching the motherboard, backplane, or add-on cards. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components on a static-dissipative surface or in a static-shielded bag when they are not in the chassis. 18. CAUTION: Any unverified component could cause unexpected damage. To ensure the correct installation, please always use the components (ex. screws) provided with the accessory box. Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage. To avoid electrical shock, always disconnect the power from your system chassis before you work on it. Don't touch any components on the main board or other cards while the system is on. Disconnect power before making any configuration changes. The sudden rush of power as you connect a jumper or install a card may damage sensitive electronic components. Warning! 1. 2. 3. 4. Input voltage rated: 6 ~ 36 Vdc (12/24V power). Transport: carry the unit with both hands and handle with care. Maintenance: to properly maintain and clean the surfaces, use only approved products or clean with a dry applicator. SD/SIM card: Turn off the power before inserting or removing the storage cards. vii TREK-722/723 User Manual TREK-722/723 User Manual viii Contents Chapter Chapter General Information ............................1 1.1 1.2 1.3 Introduction ............................................................................................... 2 General Specifications .............................................................................. 2 Dimensions ............................................................................................... 4 Figure 1.1 TREK-722 dimensions................................................ 4 Figure 1.2 TREK-723 dimensions................................................ 4 System Setup .......................................5 2.1 2.3 A Quick Tour of the TREK-722/723 Mobile Data Terminal ....................... 5 Figure 2.1 Front view of TREK-722/723 ...................................... 6 Figure 2.2 Rear view of TREK-722/723....................................... 6 Figure 2.3 Bottom view of TREK-722/723 ................................... 6 Installation Procedures.............................................................................. 6 2.2.1 Connecting the Power Cord.......................................................... 7 Figure 2.4 Power connector photo............................................... 7 Table 2.1: Pin Definition of Power Cord ...................................... 7 WinCE Satrtup Procedure......................................................................... 7 Hardware & Peripheral Installation ....9 3.1 3.2 Installing the Storage Device and SIM Card ........................................... 10 Installing Optional Accessories ............................................................... 10 Pin Assignments ...............................11 4.1 4.2 Rear Side Connectors............................................................................. 12 Extended IO ............................................................................................ 12 Table 4.1: Extended IO.............................................................. 12 Software Functionality ......................13 5.1 Introduction ............................................................................................. 14 Figure 5.1 Windows® Embedded CE 6.0 on the TREK72x platform .......................................................................... 14 Windows CE Startup Procedure ............................................................. 14 Upgrade Procedure................................................................................. 15 5.3.1 Prepare SD card for bootloader .................................................. 15 Figure 5.2 Storage format tool ................................................... 15 5.3.2 Upgrade image: .......................................................................... 15 Figure 5.3 Boot files................................................................... 15 Figure 5.4 Upgrade finish .......................................................... 16 Figure 5.5 Format disk............................................................... 16 Utilities..................................................................................................... 17 5.4.1 Test Utility ................................................................................... 17 5.4.2 Test Procedure ........................................................................... 17 Figure 5.6 Test Utility................................................................. 17 5.4.3 Startup execution ........................................................................ 18 5.4.4 Platform Setting .......................................................................... 18 Figure 5.7 General information .................................................. 19 Figure 5.8 Audio ........................................................................ 19 2.2 Chapter Chapter Chapter 5.2 5.3 5.4 ix TREK-722/723 User Manual 5.5 5.6 5.7 5.8 TREK-722/723 User Manual Network................................................................................................... 20 5.5.1 Setup for HSPA and GPRS ........................................................ 20 Figure 5.9 3G via Ethernet ........................................................ 20 Figure 5.10RF module manager................................................. 21 Figure 5.11ISP modern setting................................................... 21 5.5.2 Example for Verizon CDMA Setup ............................................. 22 Touch Calibration.................................................................................... 24 Figure 5.12Touch panel calibration ............................................ 24 Application Program Development ......................................................... 24 5.7.1 PC System requirements............................................................ 24 5.7.2 Building Windows CE program ................................................... 25 Figure 5.13Flow-chart of Building Windows® Embedded CE 6.0 runtime ..................................................................... 25 5.7.3 How to install SDK ...................................................................... 25 5.7.4 Running your application programs ............................................ 29 5.7.5 SUSI library for application program.......................................... 29 Windows® Embedded CE 6.0 Component List ...................................... 29 Chapter General Information This chapter gives background information on the TREK-722/723 Mobile Data Terminal. Sections include: Introduction General Specifications Dimensions 1.1 Introduction TREK-722/723 is a RISC platform with 5"/7" display all-in-one Mobile Data Terminal (MDT). The radio frequency options and programmable function keys make TREK722/723 suitable for local fleet management. It is designed with vehicle power compliant to ISO7637-2 & SAE J1113 ensuring the system is stable in dirty car power system. With Suspend/Wakeup feature, TREK-722/723 supports 24/7 monitoring mechanism by periodical, digital input & WWAN wakeup. 1.2 General Specifications Key features 5" & 7" LCD (800 x 480) with resistive touchscreen 24/7 monitoring & reporting Cortex-A8 TI AM3703 800 MHz WinCE6.0 & optional Android 2.3.4 Built-in CAN bus with J1939 protocol Built-in GPS with AGPS feature, BT, CDMA/GPRS/HSPA+ Operating temperature: -20 ~ 60° C (5") & -30 ~ 70° C (7") Storage temperature: -30 ~ 80° C Specifications Dimensions: 165 x 115 x 43 mm (TREK-722) / 213 x 145 x 43 mm (TREK-723) Weight: 650 gram (TREK-722) / 850 gram (TREK-723) Power feature: – Input Voltage: 6~36Vdc – Supports power on delay (default 2 seconds) – Supports power off delay (default 5 seconds) – Supports hardware power off delay (default 30 seconds) – Supports WWAN wake up SoC: TI ARM Cortex-A8 AM3703 800 MHz OS: WinCE 6.0 R3 core version / Android 2.3.4 Gingerbread RAM: On board 256MB Mobile LPDDR Storage: – On board NAND type 2GB for boot loader, OS & customer's APs – 1 x push-push type SD slot LCD: 5" industrial grade wide screen TFT LCD, 800 x 480 resolution (TREK722)/ 7" industrial grade wide screen TFT LCD, 800 x 480 resolution (TREK723) Touch Screen: 4-wire resistive with flat panel design TREK-722/723 User Manual TREK-722/723 User Manual General Information IO Function: – Audio: 1 x built-in 2 W mono speaker 1 x MIC input, 1 x mono line-in, 1 x stereo line-out via high density cable – Video: 1 x CVBS input via high density cable 1 x Y/C input via high density cable – USB Client: 1 x USB client I/F via USB mini-B connector with rubber door protection – USB Host: 1 x USB host I/F via USB A-type connector (500 mA) with rubber door protection 1 x USB host I/F via high density cable with USB A-type connector (500 mA) – Serial Port: 2 x 4-wire RS-232 via high density cable – GPIO: 2 x isolated digital input (DI) which can wake up system via high density cable 2 x isolated digital output (DO) via high density cable – CAN bus: 1 x CAN bus 2.0a/b with J1939 protocol via high density cable – Function Key: 5 x programmable function keys with green LED RF Function: – GPS (Optional): Built-in 50 channel u-blox LEA-6S with internal antenna – Bluetooth (Optional): Built-in Class 2 Bluetooth V2.1+EDR with internal antenna – WWAN (Optional) Built-in Quad-band GPRS module Cinterion TC63i with internal antenna Built-in UMTS/HSPA+ module Cinterion PH8 with internal antenna Built-in CDMA/EV-DO module Qualcomm Gobi3000 with internal antenna Environmental Specifications: – Operating Temperature : -20° C ~ 60° C & -30 ~ 70° C (7") – Relative Humidity: 10 ~ 90% @ 40° C (non-condensing) – Shock/Vibration MIL-STD-810G, SAE J1455, Class 5M3 according DIN EN 60721-3-5 – Certificate CE, FCC, CCC, UL, CUL, CB, E-mark Chapter 1 M 1.3 Dimensions 20.40 114.80 43 40 164.70 Unit: mm 144.80 3- 43 40 M4 Figure 1.1 TREK-722 dimensions 20 212.70 Unit: mm Figure 1.2 TREK-723 dimensions TREK-722/723 User Manual Chapter System Setup This chapter details system setup on TREK-722/723. Sections include: A Quick Tour of the Mobile Data Terminal Installation Procedures Running the BIOS Setup Program Installing the Drivers for Win XP 2.1 A Quick Tour of the TREK-722/723 Mobile Data Terminal Before starting to set up the Mobile Data Terminal, take a moment to become familiar with the locations and functions of the controls, drives, connectors and ports, which are illustrated in the figures below. When the Mobile Data Terminal is placed inside truck glove cabinet or under the passenger’s seat next to the driver, its front appears as shown in Figure 2.1. Figure 2.1 Front view of TREK-722/723 Figure 2.2 Rear view of TREK-722/723 Figure 2.3 Bottom view of TREK-722/723 2.2 Installation Procedures TREK-722/723 User Manual 2.2.1 Connecting the Power Cord Figure 2.4 Power connector photo Table 2.1: Pin Definition of Power Cord Pin Definition Color Blue Shield Black Black Ignition White 2.3 WinCE Satrtup Procedure Windows CE image can be loaded by two methods, first way is by SD storage card, and second way is by system on-board chip. Storage card is higher boot priority than on-board system flash chip. In BOOTLOADER criteria, it will first read the Windows CE image from external storage card. After download image done, booloader will burn image to on-board flash chip automatically. If external storage card is unavailable or no Windows CE image inside, BOOTLOADER will load the Windows CE image from on-board system flash chip. BOOTLOADER copy Windows CE image to DRAM and launch WinCE from DRAM, whenever loaded by external storage card or system on-board flash chip. TREK-722/723 User Manual System Setup Connect the three pin waterproof power cord to the DC inlet of TREK-722/723. On the open-wire end, one pin is reserved for positive voltage and is marked "+" which needs to be connected to the power "+" side; one pin is reserved for ground and is marked "-"; which needs to be connected to the power "-" side. And, one pin is reserved for the ignition signal with an “ignition” mark. There's independent "Shield" pin in power cable, please fixed its O-ring which besides of power connecter of TREK-722/723. Chapter 2 When you installing TREK-722/723, the first step will be connect the power and ignition correctly. TREK-722/723 power cable is designed to connect battery directly. TREK-722/723 can be switched ON/OFF by the ignition signal or its power button both. TREK-722/723 User Manual Chapter Hardware & Peripheral Installation This chapter details the installation of hardware for TREK-722/ 723. Sections include: Installing the Storage Device and SIM Card Installing Optional Accessories 3.1 Installing the Storage Device and SIM Card Users can install SIM card and storages (SD card) easily on TREK-722. SD card is the main bootable storage which has OS pre-installed from Advantech. 3.2 Installing Optional Accessories Optional accessories, like RAM mount kits or other functional modules are available for purchase to complement TREK-722/723. All of standard 75mm type mounting with M5 type screws only. TREK-722/723 User Manual 10 Chapter Pin Assignments This chapter explains pin assignments on the TREK-722/723. 4.1 Rear Side Connectors Extended IO SD Card USB Client Mini B USB Host Type A 4.2 Extended IO Table 4.1: Extended IO Pin Signal Pin Signal USB_G 21 USB_5V USB_G 22 USB_5V TX-A 23 USB_DP RTS-A 24 USB_DM RX-A 25 ISOD_GND CTS-A 26 DO1 TX-B 27 DO2 RTS-B 28 DI-1_N RX-B 29 DI-1_L 10 CTS-B 30 DI-2_N 11 DGND 31 DI-2_L 12 DGND 32 MIC-LINE_IN 13 J1850_P 33 AUDIO_GND 14 J1850_N 34 LINE-OUT_R 15 CAN-H 35 AUDIO_GND 16 CAN-L 36 LINE-OUT_L 17 ISO-L 37 VIDEO_GND 18 ISO-K 38 VIDEO_GND 19 S-Y 39 VIDEO_GND 20 S-C 40 CVBS TREK-722/723 User Manual 12 Chapter Software Functionality This chapter details the Windows® 6.0 operating system on the TREK72x platform. Sections include: Introduction Windows® CE Startup Procedure Upgrade Procedure Utilities Network Application Program Development Windows® Embedded CE 6.0 Require Components 5.1 Introduction The TREK72x platform is one embedded system with Windows® Embedded CE 6.0. The Windows® Embedded CE 6.0 is a compact OS that occupies less storage space or system resources compared with other operating systems such as Windows® XP. By its modular nature, it is possible to choose those functions that are useful for specific application. Not only reducing the system resources required, but also reduces start-up time. In the field of embedded applications, this is an appealing feature because the impact of downtime would be minimized. Furthermore, the small storage space it needs makes OS on solid-state disk possible, which implies higher robustness to harsh environments. Figure 5.1 Windows® Embedded CE 6.0 on the TREK72x platform 5.2 Windows CE Startup Procedure Windows CE image can be loaded by two methods, first way is by SD / MMC storage card, and second way is by system on-board chip. Storage card is higher boot priority than on-board system flash chip. In BOOTLOADER criteria, it will first read the Windows CE image from external storage card. After download image done.If external storage card is unavailable or no Windows CE image inside, BOOTLOADER will load the Windows CE image from on-board system flash chip. BOOTLOADER copy Windows CE image to DRAM and launch WinCE from DRAM, whenever loaded by external storage card or system on-board flash chip. TREK-722/723 User Manual 14 Advantech release three files for TREK72x platform. MLO&EBOOT.NB0 is bootloader and NK.BIN is WinCE6.0 image. 5.3.1 Prepare SD card for bootloader a) Disk format with HPUSBFW.EXE. Chapter 5 5.3 Upgrade Procedure Software Functionality Figure 5.2 Storage format tool b) Copy file for upgrade image: 1. Copy MLO to sd card for TI CPU boot code. 2. Copy other file to sd card(refer to Section 5.3.2). 5.3.2 Upgrade image: a) Auto Upgrade: 1. Copy MLO to sd card first. 2. Copy Figure 5.3 file to sd card for TREK72x. Figure 5.3 Boot files 3. Plug sd card to TREK72x and power on. 4. The screen will show like next picture. It is will pass through some steps about format disk and copy file °¦etc. which automatically to finish upgrade except incorrect conditions. 15 TREK-722/723 User Manual Figure 5.4 Upgrade finish b) Manual: If want to upgrade by manual must follow some steps. 1. Format disk with wince tools Storage Manager on the Control panel like Figure 5.4. 2. Copy files to Storage card that include MLO/EbootSD.nb0/NK.bin but MLO must be copied first. Relation files on the "Image" folder like a) Auto Upgrade. Figure 5.5 Format disk TREK-722/723 User Manual 16 There are several useful utilities added in the standard Windows® Embedded CE 6.0 5.4.1 Test Utility Item Function Description COMx (LOOPBACK) Lookback test for COM3 & COM8 COMx <=> COMy Two COM ports RS232 transmission TOUCH SCREEN Touch Screen function validation Audio Play Audio play function validation Audio Record Audio record function validation USB Keyboard USB Keyboard function validation USB Mouse USB Mouse function validation Backlight Test Backlight function validation DIO Control DIO function validation PAUSE Pause test process REPEAT TEST Repeat test process Etc... 5.4.2 Test Procedure You should see a lot of test items in left zone after launch this utility. You can insert enough test items you want to right zone by pressing "Add" button. The test items in right zone will be executed. Also, you can remove test items from right zone by pressing "Remove" button. After you add test items done, you can go function test by pressing "EXE ALL" button. To press "View Rpt" button, you will see the test result. Figure 5.6 Test Utility 17 TREK-722/723 User Manual Software Functionality The utility "AdvDiag.exe" is one integrated test tool, which includes the function validation for peripheral. You can use this tool to verify whether the peripheral function work or not. You just copy this utility to storage card and then launch from WinCE by double click it. Main Function : Chapter 5 5.4 Utilities 5.4.3 Startup execution The TREK72x platform has a useful function call "Startup execution". After the system boot up, the startup execution function would automatically perform. This function is useful for control system to do the initialization processes or some other procedures. In TREK72x platform, there are two ways to perform "Startup" function. Method 1: 1. Create "startup" directory in SD/MMC storage card, USB disk. 2. Copy executable files to "startup" directory that is created by Step 1. Example: We copy two executable files "softreset.exe" and "Notepad.exe" in "Startup", and then reboot the system. After the system boot up, the two executable file would automatically execute. Method 2: 1. Create "startup" directory in SD/MMC storage card, USB disk(Hard Disk). 2. Create a file called "startup.ini" in "startup" directory. Type in the commands you want to execute after boot up in that file. Example: Create "Startup.ini" in "\DiskOnChip\Startup" directory and reboot the system. The content of startup.ini was listed below: \windows\tty.exe \windows\registry.exe After the system reboot, "\windows\ tty.exe" and "\windows\ registry.exe" would automatically execute. Be sure that the two methods are independent. It means they can be used simultaneously. 5.4.4 Platform Setting Platform Setting utility is an outstanding utility designed by Advantech Windows? CE software team. It is an integrated environment where user can get useful system information as well as configure favorite system settings and apply system control function on demand. Double click the icon of Platform Setting on the desktop. Platform Setting is also put on Control Panel. Following sections illustrate the functions of Platform Setting. TREK-722/723 User Manual 18 5.4.4.2 Audio The Audio page is setting recorder that include "Microphone" and "Line In". The record function default select is "Line In". Figure 5.8 Audio 19 TREK-722/723 User Manual Software Functionality Figure 5.7 General information Chapter 5 5.4.4.1 General It shows the memory information including DRAM and on board MMC. Platform name and version control are also put here. 5.4.4.3 Miscellaneous The Misc page provides several functions as described below. The "Registry" block provides registry save and registry clean function. Pressing "Save" button, the registry settings will be saved to persistent storage as DISKONCHIP. Pressing "Clean" button, the registry setting will return to default settings. The "A.Sync" button invokes ActiveSync to the host computer. The Memory Management block will check if memory size needs to be allocated automatically during boot. Once this is checked, program memory will be allocated half size of memory, and storage memory will occupy the rest. Miscellaneous settings 5.5 Network 5.5.1 Setup for HSPA and GPRS TREK72x build in one 3G controller. It appears at "Control Panel/Network and Dialup Connections". User can configure its 3G support as follows: a) Manual 1. Click "Start/Settings/Control Panel" 2. Double click "Network and Dial-up Connections" 3. If the TREK72x is a node of the LAN with 3G servers, it is now available. 4. Support Module have Tc63i/PH8/SierraWireless Figure 5.9 3G via Ethernet TREK-722/723 User Manual 20 Chapter 5 Software Functionality TREK-722/723 User Manual 21 5.5.2 Example for Verizon CDMA Setup 1. On the next screen set the phone number to “#777” and click finish. 2. 3. Double click on the Verizon icon. Tap the dial properties, and use the drop down to select “CAR” and tap OK. TREK-722/723 User Manual 22 Tap Connect The next window will say “Dialing #777” 6. If everything is OK, after a short time, you will hear a connect sound, and the Verizon status window will say “Connected” Fill in the “extra settings” field. Picture below for reference. 23 TREK-722/723 User Manual Software Functionality Note! Chapter 5 4. 5. 5.6 Touch Calibration Want to calibrate touch panel that can be searched on "stylus property". Press recalibrate button and follow guide to finish recalibrate touch. If finish recalibrate suggest you to save registry with "5.4.4.3 Miscellaneous" keep result of touch panel calibration Figure 5.12 Touch panel calibration 5.7 Application Program Development The TREK72x is bundled with built-in Windows® Embedded CE 6.0 operating system. In real applications users need to execute various application programs on it. However, unlike its other family, the Windows® Embedded CE 6.0 is a hardwaredependent operating system. That is to say, Windows? Embedded CE 6.0 application programs are only portable in the source code level. Users must rebuild the runtime file for a different Windows® Embedded CE 6.0 platform even though the source code may not be changed at all. 5.7.1 PC System requirements Intel® Pentium-90 CPU or more advanced Microsoft® Windows® 2000 Professional or Windows® XP Microsoft® eMbedded Visual C++ 4.0 or Virtual Studio 2005 Platform SDK for TREK72x 64MB DRAM CD-ROM drive Monitor with VGA resolution at least Mouse 200MB free hard disk space at least TREK72x platform Let the host PC and TREK72x connect on the same USB1.1 to do kernel debugging if necessary USB cable (bundled in the standard TREK72x) TREK-722/723 User Manual 24 By the platform SDK bundled with the standard TREK72x, users can build the Windows CE runtime application program by the eMbedded Visual Tools. 5.7.3 How to install SDK For example copy Platform SDK file "**.msi" to your PC, and launch it. You can install SDK by steps. 1. Launch Platform SDK file, and then tap Next button. 25 TREK-722/723 User Manual Software Functionality Figure 5.13 Flow-chart of Building Windows® Embedded CE 6.0 runtime Chapter 5 5.7.2 Building Windows CE program 2. Accept License Agreement and go next. 3. Key in your information and go next. TREK-722/723 User Manual 26 Choose setup type. Chapter 5 4. Software Functionality 27 TREK-722/723 User Manual 5. Tap "Install" button to install SDK. Install SDK.... 6. Finish installing. TREK-722/723 User Manual 28 After you implement application code, you should choose Advantech SDK to compile. TREK72x is targeted to be the embedded device for system integrator. System integrator usually access platform relative IO, like backlight control, brightness control, etc. Advantech especially provide one SUSI static library to system integrator. SUSI library includes some useful APIs. System integrator just adds it to their application project, and then they can use SUSI library functions. Note: about SUSI library detail was showed in [SUSIV3.0RISC User Manual.doc] 5.8 Windows® Embedded CE 6.0 Component List APPLICATIONS AND SERVICES DEVELOPMENT Core Advantech Advantech Advantech Pro. Pro.Plus Core Pro. Pro. Plus Active Template Library (ATL) C Libraries and Runtimes C++ Runtime Support for Exception Hanx dling and Runtime Type Information Full C Runtime Standard I/O (STDIO) Standard I/O ASCII (STDIOA) String Safe Utility Functions Standard String Functions - ASCII (coresx tra) Component Services (COM and DCOM) Component Object Model COM OLE32 CoCreateGuid functionality for COM Storage DCOM COM Storage 29 TREK-722/723 User Manual Software Functionality 5.7.5 SUSI library for application program Chapter 5 5.7.4 Running your application programs DCOM Remote Access Minimal COM (No OLE Support) OLE32 CoCreateGuid functionality for COM Storage Speech Interface Speech API (SAPI) 5.0 Microsoft English (US) Windows CE Speech Recognizer (available in 4.2 only)* Lightweight Directory Access Protocol (LDAP) Client Message Queuing (MSMQ) SOAP Reliable Messaging Protocol (SRMP) Microsoft Foundation Classes (MFC) Object Exchange Protocol (OBEX) OBEX Server OBEX Inbox MSMQ ActiveX Wrappers OBEX File Browser SOAP Toolkit Client Server .NET Compact Framework OS Dependencies for .NET Compact Framework 2.0 Smart Device Authentication Utility .NET Compact Framework 2.0 SQL Server 2000 .NET Data Provider x OBEX Client Pocket Outlook Object Model (POOM) API Standard SDK for Windows CE vider SQL Server CE 2.0 .NET Data Pro- SQL Server CE 2.0 XML XML HTTP XML Query Languages (XQL) XML Stylesheet Language Transformations (XSLT) XML SAX XML Error Strings MSXML 3.0 XML Core Services and Document Object Model (DOM) XML Minimal Parser Exchange Client APPLICATIONS - END USER ActiveSync File Sync Inbox Sync Pocket Outlook Database Sync CAB File Installer/Uninstaller TREK-722/723 User Manual 30 x Microsoft Excel Viewer* Microsoft Image Viewer* Microsoft PDF Viewer* Microsoft PowerPoint Viewer* Microsoft Word Viewer* FLASH Update Sample Application Games Solitaire Help* Inbox Remote Desktop Connection Remote Desktop Protocol (RDP) User Interface Dialog Boxes Smart Card Redirection File Storage Redirection Filtered File Storage Redirection Cut/Copy/Paste Clipboard Redirection Serial and Parallel Port Redirection Audio Playback Redirection Printer Redirection Terminal Emulator Windows Messenger WordPad CORE OS SERVICES Battery Driver Display Support Serial Port Support Parallel Port Support Internet Appliance (IABASE) Support Notification LED Support PNP Notifications USB Host Support USB Human Input Device (HID) Class Driver USB HID Keyboard and Mouse USB HID Keyboard Only USB HID Mouse Only USB Printer Class Driver USB Storage Class Driver USB Remote NDIS Class Driver Debugging Tools Keyboard Test Application Touch Driver Test Application Remote Display Application Tiny Kernel Test Sample Application Toolhelp API LMemDebug Memory Debugging Hooks x Notification (Choose 1) UI based Notification Non UI based Notification 31 TREK-722/723 User Manual Software Functionality Freecell Chapter 5 File Viewers* Power Management (Choose 1) Power Management (Full) Power Management (Minimal) Device Manager Kernel Features Target Control Support (Shell.exe) Fiber API FormatMessage API Memory Mapped Files Message Queue - Point-to-Point Networking Features Domain Discovery COMMUNICATIONS SERVICES AND NETWORKING Extended DNS Querying and Update (DNSAPI) Secure DDNS Extensible Authentication Protocol Firewall Internet Connection Sharing (ICS) Gateway Logging IPSec v4 NDIS Packet Capturing DLL NDIS User-mode I/O Driver Network Bridging Network Driver Architecture (NDIS) Network Utilities (IpConfig, Ping, Route) x Reference Gateway User Interface Remote Configuration Framework TCP/IP IP Helper API TCP/IPv6 Universal Plug and Play (UPnP) Control Point API Device Host API Device Host API (Minimal Subset) Sample UPnP IGD Schema Implementation UPnP Tools UPnP Audio-Video DCP AV Control Point API AV Device API AV Renderer Sample USB Flash Config Tool Windows Networking API/Redirector (SMB/CIFS) Networking - Local Area Network (LAN) Native Wi-Fi WLAN Access Point Components Wired Local Area Network (802.3, 802.5) x Winsock Support Native Wi-Fi WLAN STA TREK-722/723 User Manual 32 x Networking - Personal Area Network (PAN) x Bluetooth Bluetooth Stack with Integrated CSR Chipset Driver Bluetooth Stack with Universal Loadable Driver Bluetooth Stack with Integrated SDIO Driver Bluetooth Stack with Integrated USB Driver Bluetooth Stack with Integrated UART Driver Bluetooth HS/HF and Audio Gatex way Service Bluetooth Profiles Support Bluetooth LAP and Configuration Utility Bluetooth DUN Gateway Bluetooth PAN Bluetooth HID Device Support Bluetooth HID – Keyboard Bluetooth HID – Mouse IrDA Networking - Wide Area Network (WAN) Dial Up Networking (RAS/PPP) AutoDial Software Functionality Bluetooth Protocol Stack with Transport Driver Support Standard Modem Support for Dial Up Networking Point-to-Point Protocol over Ethernet (PPPoE) Telephony API (TAPI 2.0) Unimodem support Virtual Private Networking PPTP L2TP/IPSec Core Server Support FTP Server Servers File Server File Server Customizable UI Windows Peer-to-Peer Networking Peer Name Resolution Protocol (PNRP) Identity Manager Print Server RAS Server/PPTP Server (Incoming) Telnet Server Web Server (HTTPD) Active Server Pages (ASP) Support JScript 5.6 33 Chapter 5 Wireless LAN (802.11) STA - Automatic Configuration and 802.1x TREK-722/723 User Manual VBScript 5.6 Device Management ISAPI Extension x WebDAV Support Web Server Administration ISAPI Web Proxy Parental Controls Simple Network Time Protocol (SNTP) SNTP Server SNTP Client with DST Device Management Client Simple Network Management Protocol (SNMP) SNTP Automatic Updates and Server Synchronization DEVICE MANAGEMENT FILE SYSTEMS AND DATA STORE Compression Database Support File and Database Replication (Choose 1) Count-Based File System - Internal (Choose 1) RAM and ROM File System ROM-only File System Registry Storage (Choose 1) Hive-based Registry RAM-based Registry Storage Manager Bit-based Storage Manager Control Panel Applet Binary Rom Image File System EDB Database Engine Partition Driver CD/UDFS File System FAT File System Transaction-Safe FAT File System (TFAT) x System Password FONTS Arial Arial (Subset 1_30) Arial Black Arial Bold Arial Bold Italic Arial Italic Comic Sans MS Comic Sans MS Comic Sans MS Bold Courier New Courier New Bold Courier New Bold Italic Courier New Italic Georgia TREK-722/723 User Manual Courier New (Subset 1_30) 34 x Georgia Bold Georgia Bold Italic Georgia Italic Impact Kino MSLogo Symbol Tahoma Times New Roman Times New Roman (Subset 1_30) Times New Roman Bold Times New Roman Bold Italic Times New Roman Italic Trebuchet MS Trebuchet MS Bold Trebuchet MS Trebuchet MS Bold Italic Trebuchet MS Italic Verdana Verdana Verdana Bold Verdana Bold Italic Webdings Verdana Italic Wingding Input Method Manager (IMM) Locale Services (Choose 1) INTERNATIONAL National Language Support (NLS) English (US) National Language Support only Locale Specific Support Arabic Tahoma (subset 1_08) Tahoma Bold (subset 1_08) Fonts Arial (subset 1_08) Arial Bold (subset 1_08) Courier New (subset 1_08) Keyboard Arabic Keyboard (101) Chinese (Simplified) Agfa AC3 Font Compression Fonts SimSun & NSimSun (Choose 1) SimSun & NSimSun 2_20) SimSun & NSimSun (Subset 35 TREK-722/723 User Manual Software Functionality Tahoma (Subset 1_07) Tahoma Bold Chapter 5 Georgia SimSun & NSimSun (Subset GB18030 Data Converter Input Method Editor (Choose 1) MSPY 3.0 for Windows CE Datax base (Choose 1) 2_50) SimSun & NSimSun (Subset 2_60) SimSun & NSimSun (Subset 2_70) SimSun & NSimSun (Subset 2_80) SimSun & NSimSun (Subset 2_90) SC_Song MSPY 3.0 for Windows CE 1.1 MB - Minimal Database x 1.3 MB - Compact Database x 1.7 MB - Standard Database x Double Spelling (Shuang Pin) soft keyboard – Large Double Spelling (Shuang Pin) soft keyboard – Small Pocket IME Double Spelling (Shuang Pin) soft keyboard – Small Chinese (Traditional) Agfa AC3 Font Compression Fonts MingLiU & PMingLiU (Choose 1) MingLiU & PMingLiU MingLiU & PMingLiU (Subset 2_70) MingLiU & PMingLiU (Subset 2_80) MingLiU & PMingLiU (Subset 2_90) MS Ming Input Method Editor Pocket IME Input Methods Input by Radical (Chang Jei) (HWX) Handwriting Recognizer Engine MboxCHT HWX Sample UI English (Worldwide) Phonetic Input (Bopomofo) Input Methods (HWX) Handwriting Recognizer Engine English (U.S.) Input Methods Transcriber Handwriting Recognition Application French TREK-722/723 User Manual 36 x Transcriber Handwriting Recognition Application German Input Methods Transcriber Handwriting Recognition Application Hebrew Fonts Tahoma (subset 1_08) Arial (subset 1_08) Tahoma Bold (subset 1_08) Arial Bold (subset 1_08) Courier New (subset 1_08) Keyboard Hebrew Keyboard Indic Hindi Fonts Mangal Keyboard Hindi Traditional Keyboard Marathi Fonts Mangal Keyboard Marathi Keyboard Punjabi Fonts Raavi Keyboard Punjabi Keyboard Telugu Fonts Gautami Keyboard Telugu Keyboard Gujarati Fonts Shruti Keyboard Gujarati Keyboard Kannada Fonts Tunga Keyboard Kannada Keyboard Tamil Fonts Latha Keyboard Tamil Keyboard 37 TREK-722/723 User Manual Software Functionality Chapter 5 Input Methods Japanese Agfa AC3 Font Compression Fonts MS Gothic & MS PGothic & MS UI Gothic (Subset 1_50) MS Gothic & MS PGothic & MS UI Gothic (Subset 1_60) MS Gothic & MS PGothic & MS UI Gothic (Subset 1_80) MS Gothic & MS PGothic & MS UI Gothic (Subset 1_90) MS Gothic & MS PGothic & MS UI Gothic (Subset 1_70) MS Gothic & MS PGothic (Subx set 30_1_19) MS Mincho & MS PMincho MS Gothic (Choose 1) MS Gothic & MS PGothic & MS UI Gothic MS Gothic & MS PGothic (Sub- set 30) Input Method Editor (Choose 1) IME 3.1 IME 3.1 Database (Choose 1) Standard Database Compact Database Optional UI Components Dictionary Tool Properties Dialog Box Advanced Settings Dialog Box (Landscape mode only) System Tray Icon Manager x Name/Place Database Supplemental Database Test IME Input Methods Pocket IME (Choose Additional Databases) All Characters List (HWX) Handwriting Recognizer Engine Sample UI Character Auto Com plete -HWX Multibox HWX Sample UI Kana Soft Keyboard Romaji/English Soft Keyboard Search by Radical Search by Stroke Korean Agfa AC3 Font Compression Fonts Gulim (GL_CE) Gulim & GulimChe (Choose 1) TREK-722/723 User Manual 38 x IME 97 Input Methods Gulim & GulimChe (Subset 1_40) Gulim & GulimChe (Subset 1_50) Gulim & GulimChe (Subset 1_60) Input Method Editor (HWX) Handwriting Recognizer Engine MboxKOR HWX Sample UI Korean Soft Keyboard Sample Thai Fonts Tahoma (subset 1_08) Keyboard Thai Kedmanee Keyboard Multilingual User Interface (MUI) Unicode Script Processor for Complex Scripts Internet Client Services Browser Application Internet Explorer 6.0 for Windows CE Standard Components Internet Explorer 6.0 Sample Browser TV-Style Navigation Components Pocket Internet Explorer Internet Explorer 6.0 for Windows CE Components Internet Explorer Browser Control Host Internet Explorer HTML/DHTML API Internet Explorer HTML Application Filter and Translation Internet Explorer Plug-in Image Decoder API Decoder Internet Explorer PNG Image Internet Explorer Theme Library Internet Explorer Multiple-Language Base API Internet Explorer Multiple-Language Full API Internet Explorer RPC Support Optional Charset/Encoding in registry Internet Explorer TV-Style Navigation Fixed-Width Layout Directional Tabbing Disable Vertical Scroll Bar and Events Customizable Font Range URL Moniker Services Windows Internet Services 39 TREK-722/723 User Manual Software Functionality Chapter 5 Gulim & GulimChe (Subset 1_30) Passport SSI 1.4 Authentication (P3P) Platform for Privacy Preferences XML Data Islands XML MIME Viewer Pocket Internet Explorer HTML View (WEBVIEW) Internet Options Control Panel Scripting JScript 5.6 Script Authoring (Jscript) Script Encode (Jscript) VBScript 5.6 Script Authoring (VBScript) Script Encode (VBScript) MsgBox and InputBox support GRAPHICS AND MULTIMEDIA TECHNOLOGIES Graphics Raster Fonts Support V1 Font Compatibility Alphablend API (GDI version) Gradient Fill Support Multiple Monitor Support Imaging Still Image Decoders PNG Decoder BMP Decoder GIF Decoder Still Image Codec Support (Encode and Decode) ICO Decoder JPG Decoder Still Image Encoders GIF Encoder BMP Encoder JPG Encoder PNG Encoder Direct3D Mobile DirectDraw Audio Audio Compression Manager GSM 6.10 Codec MSFilter Codec Waveform Audio Media Streaming Media Playback (requires WMP application) WMA and MP3 Local Playback WMA and MP3 Streaming (requires WMP application) Digital Rights Management Digital Rights Management (DRM) TREK-722/723 User Manual 40 DRM License Acquisition OCX DirectShow DirectShow Core DirectShow Display DirectShow Error Messages DMO Wrapper Filter ACM Wrapper Filter AVI Filter MPEG-1 Parser/Splitter Audio Codecs and Renderers GSM 6.10 Audio Codec IMA ADPCM Audio Codec MP3 Codec MS ADPCM Audio Codec Waveform Audio Renderer WMA Codec WMA Voice Codec Wave/AIFF/au/snd File Parser Video Codecs and Renderers DirectShow Video Renderer MPEG-1 Video Codec MS RLE Video Codec Overlay Mixer Video/Image Compression Man- ager MPEG-1 Layer 1 and 2 Audio Codec G.711 Audio Codec WMV/MPEG-4 Video Codec DVD-Video DVD-Video DVD-Video Samples Windows Media Player Windows Media Player Windows Media Player OCX Windows Media Technologies ASX v1 and M3U File Support ASX v2 File Support ASX v3 File Support Windows Media Multicast and Multi-Bit Rate NSC File Support Windows Media Streaming from Local Storage HTTP MMS Windows Media Streaming over Windows Media Streaming over SECURITY Authentication Services (SSPI) NTLM 41 TREK-722/723 User Manual Software Functionality Media Formats Chapter 5 DRM for Portable Devices Kerberos Schannel (SSL/TLS) Cryptography Services (CryptoAPI 1.0) with High Encryption Provider Personal Information Exchange Stanx dard (PKCS #12) Certificates (CryptoAPI 2.0) Cryptographic Messaging (PKCS#7) Diffie-Hellman/DSS Provider Smart Card Encryption Provider Local Authentication Sub-System Password Local Authentication Plug-in Microsoft Certificate Enrollment Tool Sample x Credential Manager Minimal GWES Configuration Minimal GDI Configuration Minimal Input Configuration Minimal Window Manager Configuration x SHELL AND USER INTERFACE Graphics, Windowing and Events Shell Graphical Shell (Choose 1) Standard Shell Windows Thin Client Shell AYGShell API Set Console Window Command Processor Command Shell User Interface Accessibility Common Dialog Support Controls Option B Control Panel Applets Customizable UI Windows XP-like Sample Skin Menu Tool Tip Mouse Network User Interface Overlapping Menus Software Input Panel Software-based Input Panel Driver Software-based Input Panel (SIP) (Choose 1 or more) SIP for Small Screens SIP for Large Screens Touch Screen (Stylus) Quarter VGA Resources - Portrait Mode x Common Controls Animation Control Common Control Windows CE Error Reporting Error Report Generator TREK-722/723 User Manual 42 Report Upload Client User Interface Error Report Transfer Driver Error Reporting Control Panel VOICE OVER IP PHONE SERVICES Phone IME PC Authentication Telephony User Interface VoIP Application Interface Layer (VAIL) Phone Provisioner Reference Media Manager Real-time Communications (RTC) Client API SIREN/G.722.1 Codecs 43 TREK-722/723 User Manual Software Functionality VAIL Database Store Chapter 5 Report Upload Client www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2012 45
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V4.4 (128-bit) User Access : Print, Extract Author : chunxia.zhao Create Date : 2012:12:27 10:20:57Z Modify Date : 2013:01:15 16:52:13+08:00 Has XFA : No Language : en XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Title : Template_V4.12_EV_User_Manual Creator : chunxia.zhao Creator Tool : FrameMaker 10.0.2 Metadata Date : 2013:01:15 16:52:13+08:00 Producer : Acrobat Distiller 10.1.4 (Windows) Document ID : uuid:d0f55cd1-c445-4fb1-90e9-e82f41b37b61 Instance ID : uuid:b323eaf5-a868-41a4-b985-bcead1ebf038 Page Mode : UseOutlines Page Count : 55EXIF Metadata provided by EXIF.tools