Advantech Co WISE1530 WiFi/BLE IoT Node User Manual rev

Advantech Co Ltd WiFi/BLE IoT Node Users Manual rev

Users Manual_rev.pdf

User Manual WISE-1530 M2.COM WIFI/BLE IoT Node
WISE-1510 User Manual 1 Copyright The documentation and the software included with this product are copyrighted 2016 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use. Acknowledgements ARM is trademarks of ARM Corporation. Freescale is trademarks of Freescale Corporation. Microsoft Windows are registered trademarks of Microsoft Corp. All other product names or trademarks are properties of their respective owners. Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events. Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For out-of- warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. Please consult your dealer for more details. If you think you have a defective product, follow these steps: 1. Collect all the information about the problem encountered. (For example, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem occurs. 2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available. 3. If your product is diagnosed as defective, obtain an RMA (return merchandize authorization) number from your dealer. This allows us to process your return more quickly. 4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty
WISE-1510 User Manual 2 service. 5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer. Declaration of Conformity FCC Class B Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipmt.t. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FOR MOBILE DEVICE USAGE (>20cm/low power) Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FOR COUNTRY CODE SELECTION USAGE (WLAN DEVICES) Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
WISE-1510 User Manual 3 USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the labelling area is small than the palm of the hand, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: M82-WISE1530 ". If the labelling area is larger than the palm of the hand, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
WISE-1510 User Manual 4 This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users. 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling FOR MOBILE DEVICE USAGE (>20cm/low power) This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: M82-WISE1530”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. NCC 低功率電波輻射性電機管理辦法  第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。  第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 模組認證： 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤。
WISE-1510 User Manual 5 2. 系統廠商應於平台上標示「本產品內含射頻模組： XXXyyyLPDzzzz-x」字樣。
WISE-1510 User Manual 6 Packing List Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately.  1 WISE-1530  1 Screw for WISE-1530  1 China RoHs Notice Optional Accessories Part No. Description 1750008001-01 Wi-Fi antenna Dipole L=141.5mm, 5dBi 2.4/5GHz 1750008653-01 1750007965-01 Antenna Cable RP-SMA to MHF4 L=200mm Antenna Cable R/P SMA (M) to MHF4, 300mm 1700015038 FPC Cable 10P-0.5mm 7.9cm for DCU2.0 1931000590 Screw M2.5x5L F/S D=5.3 H=0.8 (1+) ST Ni 1700023619-01 A cable USB-A 4P(M)/micro USB 5P(M) 1m ADAM-T212 1700025876-01 M cable USB-A 4P(M)/Plug-in 2P-5.0 90CM XRISC-ADP-10HW-AG ADP A/D 100-240V 10W 5V WM 193A231540 POST F=M3*6L M=M3*6L D=5 d=2.88 B=5 H=15 Cu Development Board Part No. Description 9696150000E ASS'Y WISE-DB1500 A101-1 M2.COM CARRIER 9696ED2200E ASS’Y WISE-ED22 A101 Daughter Board Ordering Information Part No. WISE-1530ITB-SDA10 WISE-1530 M2.COM WIFI/BLE module
WISE-1510 User Manual 7 Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage. 7. The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS. 8. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. 9. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 10. All cautions and warnings on the equipment should be noted. 11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage. 12. Never pour any liquid into an opening. This may cause fire or electrical shock. 13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. 14. If one of the following situations arises, get the equipment checked by service personnel:  The power cord or plug is damaged.  Liquid has penetrated into the equipment.  The equipment has been exposed to moisture.  The equipment does not work well, or you cannot get it to work according to the user's manual.  The equipment has been dropped and damaged.  The equipment has obvious signs of breakage. DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.
WISE-1510 User Manual 8 Change Log: Date Version Description / Major change 2017/08/08 V0.1 Draft version
WISE-1510 User Manual 9 Table of Content 1. .............................................................................................. PRODUCT OVERVIEW 10 1.1. ................................................................................................... INTRODUCTION 10 1.2. ................................................................................................... SPECIFICATIONS 11 2. ................................................................................................. H/W INSTALLATION 12 2.1. ............................................................................................ BOARD CONNECTOR 12 2.2. ............................................................................................... MODULE OUTLINE 14 2.3. ............................................................................... CONNECTOR SPECIFICATIONS 14 2.3.1. .................................................. TOP SIDE CONNECTOR PHYSICAL DIMENSIONS 14 2.3.2. ............................................................. CARRIER BOARD CONNECTION LENGTH 15 2.3.3. ............................................................... CARRIER BOARD CONNECTOR HEIGHT 16 2.4. ..................................................................................... WISE-1530 PIN-OUT MAP 17 2.5. ............................................................................. QUICK STARTER OF WISE-1530 19 2.5.1. ............................................................................... DEBUG PORT CONNECTION 錯誤! 尚未定義書籤。 3. .................................................................... DEVELOPMENT ENVIRONMENT SETUP 21 3.1. ........................................................................................................... OVERVIEW 21 3.2. ...................................................................................................... INSTALLATION 22 3.3. .............................................................................................. BUILD SOURCE FILE 22 3.4. ....................................................................... GENERATE A PROGRAMMING FILE 22 3.5 ................................................................................................... PROGRAMMING 22 4 ........................................................................... EXAMPLE: BLE WIFI INTRODUCER 22 4.1 ..................................................................................................... INSTALLATION 22 4.2. ................................................................................. STEP BY STEP USAGE GUIDE 22
WISE-1510 User Manual 10 1. Product Overview 1.1 Introduction WISE-1530 is a wireless module integrated with ARM Cortex-M4 Processor and Wifi / BLE connectivity. This technology is the best solution for WIFI and BLE combo Applications. For example, we may use BLE to configure device and transfer mass data through wifi connectivity. You may choose the WIFI or BLE to submit your sensor data according to different scenario and purpose, such as the short range with low power consumption or mass data rate to complete the specific task. Your sensors or applications with low data rate requirement can be achieved years battery lifetime in short range communication BLE. Advantech WISE-1530 also provides multi-interfaces for sensor and I/O control. With ThreadX v5.6 microprocessor operating system and add-on software stacks, it's convenient to build the application software or sensor algorithm over the OS. Data can be quickly and easily acquired and transformed into a different format to communicate with WISE-PaaS or other cloud services. Developer can build their application backbone faster and focus on their applications, value-added services. The main features of WISE-1530 are:  ARM Cortex-M4 Core Processor  Built-in Wifi / BLE connectivity  Great for Low Power Energy application  Rich interfaces for sensor and I/O control  Support ThreadX v5.6  Support wide temperature -20 ~ 70 °C
WISE-1510 User Manual 11 1.2 Specifications Processor System MCU STM32F4 ARM® 32-bit Cortex® -M4 CPU 100MHz Memory RAM 256KB Flash 1024KB Form Factor M2.COM Type A 2230 Spec. Standard M2 COM Technical SPEC_v1.1 Wireless Network Standard IEEE 802.11b/g/n and Bluetooth 4.1 Frequency Band 2.4000~2.4840 GHz for Wi-Fi 2.4000~2.4835 GHz for BLE Channels '1~13 for Wi-Fi and 79 for Bluetooth and 39 for BLE Topology Star network Transmit Power Typ. 14 dBm ± 2 at 802.11b CCK Mode 1M Typ. 12 dBm ± 2 at 802.11g OFDM Mode 54M Typ. 12 dBm ± 2at 802.11n OFDM Mode MCS0 Max 10 dBm ± 2 for BLE Receiver Sensitivity 'Typ. -95dBm at 1 Mbps Typ. -75 dBm at 54 Mbps Typ. -89 dBm at MCS0 Typ. -89 dBm for BLE RF Data Rate Up to 65Mbps Function End node Antenna connector MHF4 connector I/O UART 1 (2 wire support RTS/CTS) I2C 1 GPIO 2 SPI 1 I2S 1 ADC 4 Programming / Debug Port 1 via WISE-ED22 (CN1) Power 3.3V Environment Operational Temperature -20 ~ 70° C Operating Humidity 5% ~ 95% Relative Humidity, non-condensing
WISE-1510 User Manual 12 Physical Characteristics Dimensions (WxD) 22 x 30 mm OS ThreadX v5.6, SDK 4.1.8 * Note: Frequency Band can be configurable for Japan or Korea by request. 2. H/W Installation 2.1 Board Connector  M2.COM Type A Module  Module size: 22 mm x 30 mm  PCB thickness: 0.8 mm ± 10%  Pin count: 75 pins  Module input voltage: 3.3V DC-in  Connector mating force: 30N Maximum  Connector current rating: 0.5A / Power contact  Connector operation temperature range: -45 °C to +85 °C Figure 1 Card Edge Bevel
WISE-1510 User Manual 13 Figure 2 Card Edge Outline-Topside Figure 3 Card Edge Outline-Backside Reference from PCI Express M.2 Specification Rev 1.0 (Nov 1, 2013) Section 2.3.5 Card PCB Details
WISE-1510 User Manual 14 2.2 Module Outline The mechanical dimension information of M2.COM form factor follows the Type A 2230 module size: 22 x 30 mm. Both module types use a 75-position host interface connector and have room to support up to four RF connectors in the upper section. Figure 4 Type A 2230 2.3 Connector Specifications 2.3.1.Top Side Connector Physical Dimensions The top-side scheme has two connectors that share a common footprint but have different stack-up requirements.  Length – 22 mm maximum including land pattern  Width – 9.1 mm maximum including land pattern
WISE-1510 User Manual 15 Figure 5 Top Side Connector Physical Dimensions Reference from PCI Express M.2 Specification, Revision 1.0, November 1, 2013 2.3.2 Carrier Board Connection Length The carrier board connector of M2.COM follows the Type 2230 M.2 module connector:  The additional increase in length is 7.05mm maximum for top-side connector to the module length.  The retention screw adds 2.75 mm maximum.  The maximum extension, including land pattern, beyond the module leading edge is 4.3 mm.  M2.COM module lengths are 30 mm and 42 mm.
WISE-1510 User Manual 16 Figure 6 Carrier Board Connection Length Reference from PCI Express M.2 Specification, Revision 1.0, November 1, 2013 2.3.3 Carrier Board Connector Height The dimensions of M2.COM form factor follow the Type A 2230 -D3 M.2 module size. Hence, the carrier board connectors must choose H3.2-D3 or H4.2-D5 connector as in the following diagrams. Figure 7 H3.2-D3 Reference from PCI Express M.2 Specification, Revision 1.0, November 1, 2013
WISE-1510 User Manual 17 2.4 WISE-1530 Pin-Out Map 1 GND VCC 2 3 MICRO_USB_HS_DP VCC 4 5 MICRO_USB_HS_DN NC 6 7 GND I2S_CK_MICRO 8 9 NC I2S_WS_MICRO 10 11 NC I2S_SD_MICRO 12 13 NC NC 14 15 NC CB_RESET_OUT# 16 17 NC GND 18 19 NC CB_PWR_ON 20 21 NC UART3_TX (O)(0/3.3V) 22 23 NC Connector Key Connector Key Connector Key Connector Key Connector Key Connector Key Connector Key Connector Key UART3_RX (I)(0/3.3V) 32 33 GND NC 34 35 NC NC 36 37 NC GPIO_0_MICRO 38 39 GND GPIO_1_MICRO 40 41 NC NC 42 43 NC GPIO_3_WL 44 45 GND GPIO_4_WL 46 47 ADC0_MICRO GPIO_5_WL 48 49 ADC1_MICRO GPIO_6_WL 50 51 GND NC 52 53 ADC2_MICRO NC 54 55 ADC3_MICRO NC 56 57 GND I2C0_SDA 58 59 NC I2C0_SCL 60 61 NC SPI_MOSI 62 63 GND SPI_MISO 64 65 +VBAT_R SPI_SCK 66 67 NC SPI_CS0# 68 69 GND NC 70 71 RESET_IN# VCC 72 73 WAKEUP_MICRO# VCC 74
WISE-1510 User Manual 18 75 GND Figure 8 M.2 Connector
WISE-1510 User Manual 19 2.5 Quick Starter of WISE-1530 2.5.1 Preparing for Hardware The user needs to prepare for hardware as following: -WISE-1530, WISE-1500 and WISE-ED22. -802.11b/g/n (2.4 GHz) Wireless Access Point (AP). -PC Runs on Windows®, Mac® OS X®, and Linux® Please refer to the following steps for setup a WISE series of boards before using WISE-1530. Step01: Please prepare boards as below. ① WISE-1530 ② WISE-1500 ③ WISE-ED22 ④ WISE-ED22 reset button ⑤ CN2 on WISE-1500 ⑥ SW3 on WISE-1500  Pleas check pin1 and pin2 to “OFF” as default.  Switch pin2 to decide whether running “backup to default” while device booting. “ON”: enabled, “OFF”: disable ⑦ WISE-1530 reset button, one button on WISE-1500 and the other on WISE-ED22 ⑧ Micro USB connector  Drag-n-drop programming  Serial port and debugging  Power supplies for UART1 debug port ⑨ RF connector ⑩ ower connector
WISE-1510 User Manual 20 Step02: Connect the WISE-ED22 to PC using micro-USB cable. (Please refer to http://ess-wiki.advantech.com.tw/view/WISE-ED22_User_Manual#Connection_with_target_board ) ① Install Driver ②The device will be visible in the Device Manager as below, user can use serial tools (putty, tera term ...etc.) to key-in command.
WISE-1510 User Manual 21 3. Development Environment Setup 3.1 Overview WISE-1530 is used Cypress's WICED® SDKs to develop Wi-Fi and BLE application. WISE-1530 SDK use C/C++ language Runs on Windows® through Eclipse®-based integrated development environment (IDE). Single installer package with support for:  Wi-Fi + Bluetooth combo solution o Wi-Fi solutions o Bluetooth (Basic Rate, Enhanced Data Rate and Bluetooth Low Energy)  Sample applications for many popular use cases like o Connecting to cloud services o Low-power BLE-based sensors and beacons o Smart home gateways o BLE-WiFi introducer  Code snippets to understand WICED APIs User can refer to WICED Software to get more information.
WISE-1510 User Manual 22 3.2 Installation of WICED Studio The user can refer to the following steps for setup WICED Studio with WISE-1530 SDK. 3.2.1 Windows Install 1. Download WICED-Studio-5.2.0.22-IDE-Installer.zip 2. Extract the installer exe from the zip file to temp folder on your computer; do not execute the installer from the zip file 3. Double click the installer exe to install WICED Studio as below picture
WISE-1510 User Manual 23 4. After installation in completed, launch WICED Studio IDE from shortcut on desktop 5. When you see the Select WICED Platform page, choose the 43xxx_Wi-Fi item. You can change in "WICED Platform" in SDK toolbar also.
WISE-1510 User Manual 24 3.2.2 Copy patch file 1. Download and unzip WM-BN-BM-22_SDK_5.1.x_platform_patch.zip 2. Copy platforms and WICED folders to <SDK folder>\43xxx_Wi-Fi\ and select replace
WISE-1510 User Manual 25 3.3 Build Source File 3.3.1 Make a "Make Target" file Step1: In Make Target window click mouse right button Step2: Select New... Step3: Type "snip.gpio-WISE_1530" Field explanation: snip.gpio-WISE_1530  snip.gpio: application project name  WISE_1530: platform name, for WISE-1530 platform don't change this field
WISE-1510 User Manual 26 3.3.2 Build Project Double click "Make Target" file to build project. It is build complete when you see below
WISE-1510 User Manual 27
WISE-1510 User Manual 28 3.4 Generate a Programming File It will generate three bin files in <SDK folder>\43xxx_Wi-Fi\build folder when build complete. 1. Bootloader: waf.bootloader-NoOS-WISE_1530.bin 2. DCT( Device Configuration Table): DCT.bin: 3. Application: snip.gpio-WISE_1530.bin Download and install J-Link software, we need J-Flash tool to combine three bin files for programming.
WISE-1510 User Manual 29 3.4.1 Launch J-Flash 3.4.2 Open bootloader bin file
WISE-1510 User Manual 30 3.4.3 Merge DCT bin file 3.4.4 Merge application bin file
WISE-1510 User Manual 31 3.4.5 Save as a final bin file 上圖有誤，已和 Ercik 告知，Erick 之後會修改 3.5 Programming Generate a programming file then use WISE-ED22 to program WISE-1530. User can refer WISE-ED22 Drag-n-drop Programming section
WISE-1510 User Manual 32 3.5.1 Debug Setting Lauch a serial port tool(use tera term in this), then setting as below. Press WISE-1530 reset button, the screen will show as below.
WISE-1510 User Manual 33 4. Example: WISE-1530 Demo(StartKit) 4.1 Introduction The Demo application has two main function. One is an BLE and WiFi introducer example. It demonstrates GATT database initialization, DCT configuration, processing read/write requests from a BLE client, and sending data to the client. The BLE WiFi Introducer has two components, an app running on a WICED devices, and an app(BLE Scanner) running on Android device. The other is AgentLite exapmle. It demonstrates how to get the sensor value from WISE-1500 sensors and upload data to cloud server. 4.2 Detailed about WISE-1530 Demo The detailed behavior about this example is explained as following:  System initiation. Initiation hardware, Wi-Fi wlan connectivity, button1 thread…etc.  BLE and WiFi introducer WISE-1530 will attempt use default SSID and password connection to AP. If success, WISE-1530 will Loop in AgentLite. Otherwise BLE will advertising for set SSID and password. The manipulation follow as below Step by step usage guide .  Initiation sensor and access data from it. The TI HDC1050 has been design-in on WISE-1500. It’s a digital humidity sensor with integrated temperature sensor. The HDC1050 is initialized in example and the user can get data of humidity and temperature from it.  Loop in AgentLite or web service. When device connect to AP, there are many things needed to do including connected to WISE-PaaS server, keep getting data from sensor and data exchanged through AgentLite. It is going to infinite loop for cloud service.
WISE-1510 User Manual 34 4.2 Step by step usage guide Step 1: Download and unzip WISE_1530_patch.zip, then copy WISE_1530 folder to <SDK folder>\43xxx_Wi-Fi\apps. Project Explorer window will appear WISE_1530 folder. You can press 'F5' to refresh if you do not see. Step 2: Create a "WISE_1530.StartKit-WISE_1530" target file and build the application.
WISE-1510 User Manual 35 Step 3: Follow "Generate a Programming File" to generate a bin file, then download bin file to WISE-1530. You will see below message in console screen if success. Step 4 to step 8 are manipulated in cell phone.
WISE-1510 User Manual 36 Step 4: Install and launch the BLE Scanner app. Step 5: Drop the screen to rescan device, it will list out BLE device nearby. Find the WiFiInt device and press CONNECT button. Step 6: If the connection is successful can see the below picture then press "CUSTOM SERVICE" button.
WISE-1510 User Manual 37 Step 7: Find the UUID: ACA0EF7C-EEAA-48AD-9508-19A6F6B356 for SSID characteristic. Press the "W" button to enter input window. Input new SSID name then press the OK button. Last, user can press "R" button to check new SSID name.
WISE-1510 User Manual 38 Step 8: Find the UUID: 40B7DE33-93E4-4C8B-A876-D833B415A6CE for Password characteristic then procedure as Step5.
WISE-1510 User Manual 39 Step 9: If the join is successful can see network IP on console screen. Step 10: If Connect to broker and WISESnail success, user can see temperature, humidity, GPIO1 and GPIO2 on cloud server.
WISE-1510 User Manual 40 4.3 memory/flash usage The WISE-1530 has 1 MBytes flash and 256 KBytes RAM. The Start kit flash and memory usage is as below. Module Flash Static RAM Adv_WiseSnail 18284 27096 Bluetooth_Embedded_Low_Energy_Stack 154 57 bluetooth_low_energy 78493 9348 button_manager 588 4 command_console 3688 404 command_console_wifi 11146 0 crc 1060 0 DHCP_Server 1524 132 DNS 1724 44 GPIO_button 120 4 Host MCU-family library 15718 2492 Interrupt Vectors 388 0
WISE-1510 User Manual 41 libc 48018 3364 MQTT_Client 5643 736 Networking 5113 13280 NetX-Duo - Interfaces & Stacks 0 16 Other 170044 2930 Packet Buffers 0 23088 platform 1620 308 RAM Initialisation 4028 0 resources 385936 0 Ring_Buffer 112 0 Startup Stack & Link Script fill 144 25 Supplicant - BESL 3470 812 ThreadX 8596 400 TLV 28 0 WICED 5452 1040 WICED_Bluetooth_Firmware_Driver 36692 0 wiced_log 290 1104 wifi_utils 1082 36 WWD 20429 3176 TOTAL (bytes) 825556 89896 4.4 I/O Test (factory) 4.4.1 Introduction The I/O Test application is a WISE-1530 I/O testing example. It's need extra I/O board(WISE-ED30) to plug in to WISE-1500. The hardware setup as below. This instance could test m2.com I/O that WISE-1530 supported(M2.COM Pinout), include GPIO, ADC, I2C. SPI...etc interface. It used WICED SDK API to read and write I/O.
WISE-1510 User Manual 42 4.4.2 I/O Test Use WICED API Step 1: Download and unzip WISE_1530_patch.zip, then copy WISE_1530 folder to <SDK folder>\43xxx_Wi-Fi\apps. Step 2: I/O test source code please refer as below files.
WISE-1510 User Manual 43 Step 3: Create a "WISE_1530.factory-WISE_1530" target file and build the application. Download firmware to WISE-1530 then press reset button. Step 4: You will see below message in console screen if success. Input '1' to select I/O Function Test, the screen will show I/O test items.Input 1~7 to test I/0 and 0 to return previous page.
WISE-1510 User Manual 44 4.4.3 I/O Test Use SUSI API The I/O Test example also support SUSI API (please refer SUSI_API).The SUSI support GPIO, I2C, SPI, ADC and PWM APIs. You can simple revise setting to accomplish SUSI API I/O Test. Step 1: The SUSI API I/O test source code are as below files. Step 2: Open SimpleCli.mk and change USE_SUSI_API to 1.
WISE-1510 User Manual 45 Step 3: Double click "WISE_1530.factory-WISE_1530" target file and build the application. Then download the firmware to WISE-1530, you can see the screen that same as I/O Function Test.

Navigation menu