Aeon Labs FT098 Bulb , LED Bulb User Manual
Aeon Labs LLC. Bulb , LED Bulb
User Manual
View the expanded manual:
http://aeotec.com/support
Aeotec by Aeon Labs RGB Bulb.
Aeotec RGB Bulb is a low-cost Z-Wave LED module which
allows control (on/off/dim) with the use of Z-Wave.
It’s a bulb has a Smart RGB LED, which can be used to add
colour to your home. The bulb has 5 main colour channels
available for you to adjust: Red, Green, Blue, Warm White
and Cold White. You can congure its colour according to your
favour.
The RGB Bulb is also a security Z-wave device and supports
the Over The Air (OTA) feature for the product’s firmware
upgrade.
Getting your RGB Bulb up and running is as simple as
plugging it into a wall socket and linking it to your existing
Z-Wave network. The following instructions tell you how to
link your RGB Bulb to your Z-Wave network using an Aeotec
by Aeon Labs’ Z-Stick or Minimote controller. If you are using
other products as your main Z-Wave controller, such as a
Z-Wave gateway, please refer to the part of their respective
section of their instruction manual that tell you how add new
devices to your network.
If you’re using a Z-Stick: If you’re using a Minimote:
1.
2.
3.
4.
5.
6.
7.
1.
2.
3.
4.
5.
6.
Decide on where you want your RGB Bulb to be placed and
plug it in to a wall outlet. Its RGB LED will be active with a
colourful gradient.
If your Z-Stick is plugged into a gateway or a computer,
unplug it.
Take your Z-Stick to your RGB Bulb.
Press the Action Button on your Z-Stick.
Press the external switch of RGB Bulb to turn it off and then
press the external switch again to turn it on.
If RGB Bulb has been successfully linked to your Z-Wave
network, its warm white LED will be solid. If the linking was
unsuccessful, the RGB Bulb will continue to be active with
a colourful gradient.
Press the Action Button on the Z-Stick to take it out of
installation mode and return it to your gateway or computer.
Decide on where you want your RGB Bulb to be placed
and plug it in to a wall socket. Its RGB LED will be active
with a colourful gradient.
Take your Minimote to your RGB Bulb.
Press the Include button on your Minimote.
Press the external switch of RGB Bulb to turn it off and then
press the external switch again to turn it on.
If RGB Bulb has been successfully linked to your Z-Wave
network, its warm white LED will be solid. If the linking was
unsuccessful, and the RGB Bulb will continue to be active
with a colourful gradient.
Press any button on your Minimote to take it out of
installation mode.
®
Familiarize yourself with your RGB Bulb.
Quick start. With your RGB Bulb now working as a part of your smart
home, you’ll be able to configure it to indicate different
colours from your home control software via setting the RGB
value. Please refer to your software’s user guide for precise
instructions on conguring your RGB Bulb to your needs.
You’re able to change your RGB Bulbs colour manually. After
the RGB Bulb is included into your network, switching the
RGB Bulb on and off 2 times within 2 seconds via external
switch will change the colour to the next (Warm white, Cold
white, Red, Green or Blue).
Your RGB Bulb can be removed from your Z-Wave network
at any time. You’ll need to use your Z-Wave network’s main
controller, and to do this, and the following instructions will tell
you how using the Aeotec by Aeon Labs’ Z-Stick or Minimote
controller. If you are using other products as your main Z-Wave
controller, please refer to the part of their respective manuals
that tells you how remove devices from your network.
Removing your RGB Bulb from a Z-Wave network.
If you’re using a Z-Stick:
1.
2.
3.
4.
5.
6.
If your Z-Stick is plugged into a gateway or a computer,
unplug it.
Take your Z-Stick to your RGB Bulb.
Press the Action Button on your Z-Stick.
Press the external switch of RGB Bulb to turn off and then
press the external switch again to turn on it, repeat the
operation 3 times within 2 seconds.
If your RGB Bulb has been successfully removed from
your network, Its RGB LED will be active with a colourful
gradient. If the removal was unsuccessful, the RGB LED
will be solid.
Press the Action Button on the Z-Stick to take it out of
removal mode.
If you’re using a Minimote:
1.
2.
3.
4.
5.
Take your Minimote to your RGB Bulb.
Press the Remove Button on your Minimote.
Press the external switch of RGB Bulb to turn off and then
press the external switch again to turn on it, repeat the
operation 3 times within 2 seconds.
If your RGB Bulb has been successfully removed from
your network, Its RGB LED will be active with a colourful
gradient. If the removal was unsuccessful, the RGB LED
will be solid.
Press any button on your Minimote to take it out of removal
mode.
Technical specications.
External Switch
Bulb , LED Bulb
Model number: FT098-A52 & ZW098-A52.
Bulb holder type: E26 for USA version, E27 for EU/AU version.
Max power: 9W.
Max standby power: 1W.
Operating temperature: -10 to 45 .
C C
Relative humidity: 8% to 80%.
Operating distance: Up to 500 feet/150 metres outdoors.
AC Input:
Version Input (Standby Power) Working band
AU 230V 50Hz, Max: 22mA 921.42MHz
BR 220V 60Hz, Max: 21mA 921.42MHz
CN 220V 50Hz, Max: 21mA 868.40MHz
EU 230V 50Hz, Max: 22mA 868.42MHz
IL 230V 50Hz, Max: 22mA 916.02MHz
IN 230V 50Hz, Max: 22mA 865.20MHz
UK 230V 50Hz, Max: 22mA 868.42MHz
US 120V 60Hz, Max: 13mA 908.42MHz
Warranty.
Aeon Labs warrants to the original purchaser of Products that
for the Warranty Period (as dened below), the Products will
be free from material defects in materials and workmanship.
The foregoing warranty is subject to the proper installation,
operation and maintenance of the Products in accordance
with installation instructions and the operating manual
supplied to Customer. Warranty claims must be made by
Customer in writing within thirty (30) days of the manifestation
of a problem. Aeon Labs' sole obligation under the foregoing
warranty is, at Aeon Labs' option, to repair, replace or correct
any such defect that was present at the time of delivery, or
to remove the Products and to refund the purchase price to
Customer.
The "Warranty Period" begins on the date the Products is
delivered and continues for 12 months.
Any repairs under this warranty must be conducted by an
authorized Aeon Labs service representative and under Aeon
Labs' RMA policy. Any repairs conducted by unauthorized
persons shall void this warranty.
Excluded from the warranty are problems due to accidents,
acts of God, civil or military authority, civil disturbance, war,
strikes, fires, other catastrophes, misuse, misapplication,
storage damage, negligence, electrical power problems, or
modication to the Products or its components.
Aeon Labs does not authorize any person or party to assume
or create for it any other obligation or liability in connection
with the Products except as set forth herein.
Aeon Labs will pass on to Customer all manufacturers’
Material warranties to the extent that they are transferable, but
will not independently warrant any Material.
Customer must prepay shipping and transportation charges for
returned Products, and insure the shipment or accept the risk
of loss or damage during such shipment and transportation.
Aeon Labs will ship the repaired or replacement products to
Customer freight prepaid.
Customer shall indemnify, defend, and hold Aeon Labs
and Aeon Labs' affiliates, shareholders, directors, officers,
employees, contractors, agents and other representatives
harmless from all demands, claims, actions, causes of action,
proceedings, suits, assessments, losses, damages, liabilities,
settlements, judgments, nes, penalties, interest, costs and
expenses (including fees and disbursements of counsel) of
every kind (i) based upon personal injury or death or injury
to property to the extent any of the foregoing is proximately
caused either by a defective product (including strict liability
in tort) or by the negligent or willful acts or omissions of
Customer or its ofcers, employees, subcontractors or agents,
and/or (ii) arising from or relating to any actual or alleged
infringement or misappropriation of any patent, trademark,
mask work, copyright, trade secret or any actual or alleged
violation of any other intellectual property rights arising from or
in connection with the products, except to the extent that such
infringement exists as a result of Aeon Labs' manufacturing
processes.
IN NO EVENT SHALL AEON LABS BE LIABLE FOR ANY INDIRECT,
INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES,
OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE
INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN
AN ACTION IN CONTRACT, OR TORT, OR OTHERWISE EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. AEON LABS'
LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY FOR ANY CAUSE
OF ACTION ARISING IN CONNECTION WITH THIS AGREEMENT
OR THE SALE OR USE OF THE PRODUCTS, WHETHER BASED ON
NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY, BREACH
OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY
LIMITED TO, AT AEON LABS' OPTION, REPLACEMENT OF, OR
REPAYMENT OF THE PURCHASE PRICE FOR THAT PORTION OF
PRODUCTS WITH RESPECT TO WHICH DAMAGES ARE CLAIMED.
ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS
AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE
DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30)
DAYS FROM AEON LABS'S DELIVERY, OR THE DATE FIXED FOR
DELIVERY IN THE EVENT OF NONDELIVERY.
THE INDEMNITY AND WARRANTY IN ABOVE ARE EXCLUSIVE AND
IN LIEU OF ALL OTHER INDEMNITIES OR WARRANTIES, WHETHER
EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
FCC NOTICE (for USA)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR
TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS
TO THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY
LOCATIONS. DO NOT IMMERSE IN WATER. NOT FOR USE WHERE
DIRECTLY EXPOSED TO WATER.
This device may not cause harmful interference, and
This device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
1
2
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consul the dealer or an experienced radio/TV technician
for help.
Do not dispose of electrical appliances as unsorted
municipal waste, use separate collection facilities.
Contact your local government for information regarding
the collection systems available.
Warning
Certications (regional):
Z-Wave and Z-Wave Plus are registered trademarks of Sigma
Designs and its subsidiaries in the United States and other countries
Version:501009800001-AA