AeroScout EX3300 Hand Hygiene Integrated Exciter EX-3300 User Manual
AeroScout Hand Hygiene Integrated Exciter EX-3300
Contents
- 1. Users Manual
- 2. User Manual
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2606174 |
| Application ID | L9vuglzOQQUNZb9QFaYJGw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 64.23kB (802838 bits) |
| Date Submitted | 2015-05-06 00:00:00 |
| Date Available | 2015-05-06 00:00:00 |
| Creation Date | 2015-04-13 15:46:18 |
| Producing Software | Adobe PDF Library 10.0 |
| Document Lastmod | 2015-04-13 15:46:22 |
| Document Title | EX3300 Series Exciter Installation & Configuration Guide |
| Document Creator | Acrobat PDFMaker 10.1 for Word |
| Document Author: | daniel.pearlman@aeroscout.com |
EX3300 SERIES EXCITERS INSTALLATION & CONFIGURATION GUIDE Disclaimer The information and know-how included in this document are the exclusive property of STANLEY Healthcare and are intended for the use of the addressee or the user alone. The addressees shall not forward to another their right of using the information, know-how or document forwarded herewith, in whole or in part in all matters relating or stemming from or involved therein, whether for consideration or without consideration, and shall not permit any third party to utilize the information, know-how or the documents forwarded herewith or copies or duplicates thereof, unless at the company’s consent in advance and in writing. Any distribution, advertisement, copying or duplication in any form whatsoever is absolutely prohibited. The Company reserves the right to sue the addressee, user and/or any one on their behalves, as well as third parties, in respect to breaching its rights pertaining to the intellectual rights in particular and its rights of whatever kind or type in the information, know-how or the documents forwarded by them herewith in general, whether by act or by omission. This document is confidential and proprietary to STANLEY Healthcare and is not to be distributed to any persons other than licensed AeroScout Visibility System users or other persons appointed in writing by STANLEY Healthcare. Trademark Acknowledgements AeroScout is a trademark of Stanley Black & Decker, Inc. or its affiliates. Other brand products and service names are trademarks or registered trademarks of their respective holders. Below is a partial listing of other trademarks or registered trademarks referenced herein: Cisco™ is a trademark of Cisco Systems, Inc. Sun, Sun Microsystems, the Sun Logo, Java, JRE and all other Sun trademarks, logos, product names, service names, program names and slogans that are referred to or displayed in this document are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries. This product includes software developed by the Apache Software Foundation (http://www.apache.org/). This product includes code licensed from RSA Data Security Skype, SkypeIn, SkypeOut, Skype Me, the Skype Logo and the S logo and other marks indicated on Skype’s website are trademarks of Skype Limited or other related companies. ESper is a trademark of EsperTech, Inc. Jboss is a trademark of Red Hat Middleware, LLC. Oracle 10G is a registered trademark of Oracle Corporation and/or its affiliates. MS SQL Server 2005 is a registered trademark of Microsoft Corporation in the United States and/or other countries. JasperSoft, the JasperSoft Logo, JasperReports, the JasperReports logo, JasperIntelligence, JasperDecisions, JasperAnalysis, Scope Center, Scope Designer, and JasperServer are trademarks or registered trademarks of JasperSoft, Inc. in the United States and other countries. 2015 STANLEY Healthcare. All rights reserved. Doc: 0981-184-000 Rev A Published: 2015/04/02 KB Article: 5587 EX3300 Series Exciter Installation & Configuration Guide Table of Contents Introduction .........................................................................................................4 EX3300 Features ...................................................................................................5 Supported Dispenser Models ...............................................................................6 Installing the Exciters ...........................................................................................7 Adding the Exciters to the Engine Manager ..................................................... 18 Advanced Configuration ....................................................................................20 Replacing a Malfunctioning Exciter................................................................... 21 EX3300 Series Exciter Models and Cables Summary.......................................... 22 EX3300 Specifications.........................................................................................23 EX3300 Series Exciter Installation & Configuration Guide Introduction The EX3300 Series Embedded Exciters are key components of STANLEY Healthcare’s Hand Hygiene Compliance Monitoring Solution. Together with STANLEY Healthcare’s suite of enterprise visibility solutions, the EX3300 Exciters provide robust and sophisticated RFID detection and monitoring capabilities. The EX3300 Exciters are designed specifically to be embedded in touch free or automated Hand Hygiene dispensers. When a dispenser with an embedded EX3300 Exciter is activated, the Exciter triggers a tag located in range of the Exciter and the tag in turn transmits a message to a location receiver or compatible access point in range. This provides instant acknowledgment that a tagged staff member has used the dispenser. The Hand Hygiene Compliance Monitoring Solution detects, records, and reports dispenser usage by staff member, providing a revolutionary way for healthcare facilities to monitor staff compliance with the hand hygiene policy. Figure 1: EX3300 embedded in a dispenser triggering a staff tag Introduction EX3300 Series Exciter Installation & Configuration Guide EX3300 Features Hand Hygiene Dispenser Integration EX3300 Exciters are designed to be embedded in specific touch free or automated GoJo or Ecolab dispensers. The embedded Exciter reacts to dispenser activation and triggers the tag, in range, to transmit a message. Configurable Transmission Range EX3300s have a range of up to2 meters (6.5 ft.) which can be configured using the Exciter Manager Tool. Exciter Type Identification EX3300 Exciters are configured with a predefined message identifying them as Hand Hygiene devices. The triggered tag transmits the message over the network. MobileView identifies the message as a Hand Wash event. EX3300 Features EX3300 Series Exciter Installation & Configuration Guide Supported Dispenser Models The EX3300 Exciters are designed for integration in the following GoJo and EcoLab dispensers. Image Description GOJO TFX Touch Free Dispensers Includes the following TFX dispenser brands: • PURELL TFX Touch Free Dispenser • PURELL Surgical Scrub TFX Touch Free Dispenser • PROVON TFX Touch Free Dispenser GOJO LTX Touch Free Dispensers GOJO TFX Provon with CHG Dispensers EcoLab Next Gen Touch-Free Dispenser EcoLab NEXA Touch-Free Dispensers Supported Dispenser Models EX3300 Series Exciter Installation & Configuration Guide Installing the Exciters This chapter describes how to install the EX3300 Exciters in the different dispenser models. Each dispenser model is compatible with a specific EX3300 Exciter model. Note The EX-3300 Exciter must only be installed in the EcoLab Hand Sanitizer Dispenser or the GoJo Hand Sanitizer Dispensers. Installing the EX3300 Exciter in an EcoLab Next Gen Dispenser To open the dispenser: 1. Press the large button situated on the bottom of the dispenser. This releases the (bottom) hinged dispenser outer casing from the back panel, allowing it to open forwards. Note Approach the dispenser from the side, being careful not to activate the dispensing mechanism. To Install the EX3300 Exciter: 1. Remove the tape from the double sided Velcro on the back of the Exciter casing. 2. Align the positioning nodes on the Exciter casing with the holes on the dispenser's front panel and fix the Exciter in place. Installing the Exciters EX3300 Series Exciter Installation & Configuration Guide To attach the Exciter Connector Cable: 3. Connect the black connector of the connector cable into the Exciter. 4. Remove the entire internal dispenser mounting assembly from the dispenser casing by depressing the holding clip on the top of the assembly. 5. Route the cable over the top of the assembly ensuring the cable is not snagged or twisted. 6. Apply the connector wire retaining tape to the top of the mounting assembly. Installing the Exciters EX3300 Series Exciter Installation & Configuration Guide 7. Connect the white connector in the socket provided on the back of the mounting assembly. 8. Replace the dispenser mounting assembly in the case. Installing the Exciters EX3300 Series Exciter Installation & Configuration Guide To Install the Soap Container: The soap dispenser is installed with the offset dispensing nozzle on the bottom of the container positioned facing forwards. 1. Remove the protective cap covering the dispensing nozzle 2. On the dispenser tilt the white cylindrical nozzle mount forwards. 3. In the tilted position align and insert the dispenser nozzle in the cylindrical mount. 4. Once aligned push the soap container into the vertical position, locking the container in place. 5. After replacing the soap dispenser and/or the Exciter, close the dispenser casing and test the both the dispensing mechanism and Exciter operation. Installing the Exciters 10 EX3300 Series Exciter Installation & Configuration Guide Installing the EX3300 in an EcoLab NEXA Dispenser To open the dispenser: 1. Simultaneously press the two buttons situated on both sides of the dispenser. This releases the front of the dispenser's outer casing, allowing it to open forwards. To Install the EX3300 Exciter: 2. Remove the tape from the double sided Velcro on the back of the Exciter casing. 3. For the standard NEXA dispenser, place the Exciter vertically on the front panel of the dispenser. 4. For the compact NEXA dispenser, place the Exciter horizontally on the internal side panel of the dispenser. Installing the Exciters 11 EX3300 Series Exciter Installation & Configuration Guide Figure 2: Exciter placement in NEXA standard (right) and NEXA Compact (left) To attach the Exciter Connector Cable: 1. Connect the black connector of the connector cable to the Exciter. 2. Remove the soap container if needed. 3. Insert the white connector into the socket provided on the front of the dispenser. A protective rubber cover may need to be removed from this socket before inserting the connector. Installing the Exciters 12 EX3300 Series Exciter Installation & Configuration Guide 4. After replacing the soap container, close the dispenser casing and test both the dispensing mechanism and Exciter operation. Installing the Exciters 13 EX3300 Series Exciter Installation & Configuration Guide Installing the EX3300 in a GOJO TFX Dispenser To open the dispenser: 1. Open the dispenser by pressing the large button situated on the bottom of the dispenser. This releases the (bottom) hinged outer casing of the dispenser, from the back panel, allowing it to open forwards. Note Approach from the side, being careful to not activate the dispensing mechanism. To install the Exciter: 1. Remove the soap container if needed. 2. Remove at least one of the batteries in the dispenser to disable the power. 3. Insert the Exciter in the slot provided. A grey plug may be located in the connector slot. This plug must be removed before the Exciter can be inserted. Installing the Exciters 14 EX3300 Series Exciter Installation & Configuration Guide Exciter 4. Re-insert the battery into the dispenser. 5. Reinstall the soap container back into the dispenser. 6. Close the dispenser casing. 7. Test the Exciter and dispenser operation. Installing the Exciters 15 EX3300 Series Exciter Installation & Configuration Guide Installing the EX3300 in a GOJO LTX Dispenser To open the dispenser: Simultaneously press the two buttons situated on both sides of the dispenser. This releases the front of the dispenser's outer casing, allowing it to open forwards. To install the Exciter: 1. Remove at least one of the batteries of the dispenser to cut the power to it. 2. Snap the Exciter into its customized compartment in the front side of the dispenser. There may be a need to remove a plastic placeholder from the compartment. This is done by simply snapping it out. 3. Plug the Exciter's audio jack cable into the dispenser's connector. Installing the Exciters 16 EX3300 Series Exciter Installation & Configuration Guide Audio jack Exciter 4. Insert the battery/s that was removed back into the dispenser. 5. Insert the soap container back into the dispenser. 6. Close the dispenser casing. 7. Test the Exciter and dispenser operation. Installing the Exciters 17 EX3300 Series Exciter Installation & Configuration Guide Adding the Exciters to the Engine Manager Follow these steps: 1. 2. Do one of the following: • In a Cisco-based configuration using MSE 7.4 or below, add Exciters via the Cisco NCS/PI when, Consult Cisco documentation for further information • In a non Cisco environment or when using Cisco MSE 7.5 or above add Exciters via AeroScout Engine Manager Access Engine Manager and perform the following steps for each one of the Hand Hygiene Exciters: a. In the Configuration menu select Advanced Mode. b. Double-click on the Exciter icon on the map to access the Exciter Properties. c. In the Exciter Modules dialog box, check the Internal LF Exciter box. d. Ensure the Connected to Network check-box is not selected. e. Select the Settings tab. f. In HW ID, enter the Exciter ID. The Exciter ID is located on a sticker on the front cover of the Exciter. The ID can also be read from the Exciter using the Exciter Manager Tool and the Exciter's serial cable. Adding the Exciters to the Engine Manager 18 EX3300 Series Exciter Installation & Configuration Guide Note If the ID is already in use by another Exciter, and the Exciter is reachable (not offline), the system automatically switches IDs between the two Exciters. If the Exciter is unreachable, change the ID manually. g. Click OK. h. Ensure all dispenser Exciters appear offline on the map Adding the Exciters to the Engine Manager 19 EX3300 Series Exciter Installation & Configuration Guide Advanced Configuration Advanced configuration of the EX3300 Exciter is done via the Exciter Manager. The Exciter Manager Tool enables configuring the Exciter's maximum transmission range and Exciter ID. EX3300 Exciters are configured using a customized serial cable via the Exciter Manager Tool. The cable is not supplied with the Exciters and must be ordered separately. For more instructions on configuring the EX3300 Exciter, please refer to the Exciter Manager User Guide. Depending on the dispenser type (Gojo, EcoLab), embedded EX3300 Exciters require different serial cables. Figure 3: Customized EX3300 Serial Cable for GoJo TFX Dispensers (SKU: CAB-3300) Figure 4: Customized EX3300 Serial Cable for EcoLab Dispensers (CAB-3300-CN) Advanced Configuration 20 EX3300 Series Exciter Installation & Configuration Guide Figure 5: Customized EX3300 Serial Cable for GOJO LTX and TFX Dispensers (CAB-3300LTX) Replacing a Malfunctioning Exciter If an embedded EX3300 Exciter is identified as malfunctioning or damaged it can be replaced on site by performing the following tasks: 1. Open the dispenser and remove the EX3300 Exciter. 2. Using the Exciter serial configuration cable and the Exciter Manager Tool configure the Exciter ID of the replacement Exciter, with the same ID as the malfunctioning/damaged Exciter. It is recommended to annotate the new ID on the Exciter housing for future needs. 3. Configure the range of the Exciter (if required). 4. Install the replacement EX3300 Exciter in the Dispenser. 5. Test the Exciter. Replacing a Malfunctioning Exciter 21 EX3300 Series Exciter Installation & Configuration Guide EX3300 Series Exciter Models and Cables Summary Vendor SKU EX-3300-ELB Name EX3300 Hand Hygiene Exciter for EcoLab Next Gen Dispensers Dispenser Type Dispenser Image Next Gen Part Number Exciter Image 92021121 eKey Configuration Cable N/A CAB-3300-CN N/A CAB-3300-CN Cable Image Long Cable EcoLab EX-3300-NEXA EX3300 Hand Hygiene Exciter for EcoLab NEXA Dispensers NEXA 92021188 (large) 92021184 (small) Short Cable GOJO EX-3300-LTX EX3300 Hand Hygiene Exciter for GOJO LTX Dispensers LTX 1971-04 (large) 1371-04 (small) N/A CAB-3300-LTX EX-3300-PRL EX3300 Hand Hygiene Exciter for GOJO TFX Purell Dispensers TFX 2720-12 Grey CAB-3300 EX-3300-PRV EX3300 Hand Hygiene Exciter for GOJO TFX Provon Dispensers TFX 2745-12 Grey CAB-3300 EX-3300-PRS EX3300 Hand Hygiene Exciter for GOJO TFX Purell Surgical Scrub Dispensers TFX 2785-12 Orange CAB-3300 EX-3300-CHG EX3300 Hand Hygiene Exciter for GOJO TFX Provon with CHG Dispensers TFX 2845-12 Natural CAB-3300 EX3300 Series Exciter Models and Cables Summary 22 EX3300 Series Exciter Installation & Configuration Guide EX3300 Specifications Physical and Mechanical for the GoJo TFX Exciter (including housing) • Dimensions: 80 x 48 mm x 45 mm (3.2 in. x 1.9 in. x 1.8 in.) • Weight: 30 g (1.1 oz.) Physical and Mechanical for the GoJo LTX Exciter (including housing) • Dimensions: 80 x 48 mm x 20 mm (3.2 in. x 1.9 in. x 0.8 in.) • Weight: 30 g (1.1 oz.) Physical and Mechanical for the EcoLab Exciters (including housing) • Dimensions: 62 x 63 mm x 13 mm (2.4 in. x 2.5 in. x 0.5 in.) • Weight: 20 g (0.7 oz.) Coverage • Adjustable coverage range up to 2 m (6.5 ft.) by intervals of 0.25 m (0.8 ft.) LF Channel • 125 kHz • Field intensity limits: 37.3 dBµA/m at 10 m (ETSI) • Propagation limits: 21.8 dBµV/m at 300 m (FCC) • Modulation: ASK Power • Use only alkaline batteries as provided by the manufacturer • Input voltage range: • GoJo 3V – 4.6V • Ecolab 3.6V – 4.6V • Maximum power consumption: 1 W • Maximum current: 6A (including short circuiting and overload) Environmental • Operating temperature: 0 to 50 °C (32°F to 122°F) • Humidity: 0 to 95%, non-condensing EX3300 Specifications 23 EX3300 Series Exciter Installation & Configuration Guide Certifications • • EMC Certifications US standard: FCC part 15 European standard: ETSI 300.328, 300.330, ETSI 301.489 Canada: RSS 210 per demand EMC standard for healthcare: IEC 6100 / EN 60601 Japan : ARIB per demand Australia : C-tick per demand Korea : MIC per demand Safety Certifications US – cTUVus: UL 60950 Europe – CE mark: EN 60950 EX3300 Specifications 24 WARNING: Insertion of an EX-3300 Exciter into any host other than the EcoLab Hand Sanitizer Dispenser or the GoJo Hand Sanitizer Dispenser invalidates the FCC ID authorization and Industry Canada certification of the EX-3300 Exciter. WARNING: This device complies with Part 15 of the FCC Rules and RSS-210 of Industry and Science Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnemen. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Compliance Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures: – Re-orient or re-locate the receiving antenna. – Increase the distance between the device and the receiver. – Connect the device to an outlet on a circuit different from the one that supplies power to the receiver. – Consult the dealer or an experienced radio/TV technician. About STANLEY Healthcare STANLEY Healthcare provides over 5,000 acute care hospitals and 12,000 long-term care organizations with enterprise solutions that transform safety, security and operational efficiency. The STANLEY Healthcare solution set enables customers to achieve organizational excellence and superior care in five critical areas: Security & Protection, Safety, Environmental Monitoring, Clinical Operations & Workflow, and Supply Chain & Asset Management. These solutions are complemented by consulting, training, implementation and integration services. STANLEY Healthcare is proud to be part of Stanley Black & Decker, Inc. For more information, visit: www.stanleyhealthcare.com STANLEY Healthcare 130 Turner Street Building 3 Waltham, MA 02453 Tel: +1-888-622-6992 Asia-Pacific E-mail: stanleyhealthcare-asiapac@sbdinc.com North America E-mail: stanleyhealthcare@sbdinc.com Middle East E-mail: stanleyhealthcare-MEA@sbdinc.com Europe E-mail: shs-uk@sbdinc.com Latin America E-mail: stanleyhealthcare-latam@sbdinc.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : daniel.pearlman@aeroscout.com Create Date : 2015:04:13 15:46:18+03:00 Modify Date : 2015:04:13 15:46:22+03:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2015:04:13 15:46:22+03:00 Creator Tool : Acrobat PDFMaker 10.1 for Word Document ID : uuid:6c850715-ccac-4f0c-b712-8724eee0efde Instance ID : uuid:674b4010-843c-454a-9119-1734e08576df Subject : 4 Format : application/pdf Title : EX3300 Series Exciter Installation & Configuration Guide Creator : daniel.pearlman@aeroscout.com Producer : Adobe PDF Library 10.0 Source Modified : D:20150413124611 Company : Hewlett-Packard Page Layout : OneColumn Page Count : 26EXIF Metadata provided by EXIF.tools