Aerohive Networks HIVEAP170 Wireless Access Points User Manual Aerohive Compliance

Download:
Mirror Download [FCC.gov]
Document ID	1668214
Application ID	skhdLLm5eVfvrxCJvkWaOA==
Document Description	Updated user manual-compliance sheet
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.91kB (173854 bits)
Date Submitted	2012-04-03 00:00:00
Date Available	2012-04-03 00:00:00
Creation Date	2012-03-29 11:43:06
Producing Software	Acrobat Distiller 9.5.0 (Windows)
Document Lastmod	2012-03-29 11:43:06
Document Title	Microsoft Word - Aerohive_Compliance
Document Creator	PScript5.dll Version 5.2.2
Document Author:	csaleem

Aerohive HiveAP Compliance Information
Federal Communication Commission Interference
Statement
The availability of some specific channel and/or operational frequency bands
are country dependent and are firmware programmed at the factory to match
the intended destination. The firmware setting is not accessible by end user.
Aerohive products (FCC models, AH-AP-110-N-FCC, AH-AP-120-N-FCC,
AH-AP-170-N-FCC, AH-AP-320-N-FCC, AH-AP-330-N-FCC, AH-AP-340-N-FCC ,
AH-AP-350-N-FCC, AH-BR100-N-FCC,AH-BR200-WP-N-FCC) comply with part 15
of the FCC Rules when operating under the following restrictions: (1) they do
not cause harmful interference, and (2) they must accept any RF interference
received, including interference that might cause an unwanted impact on
their operation.
Only attach antennas that are certified for use with this device. Replacing
antennas with unauthorized, high-gain antennas greatly increases the risk of
interference and invalidates the FCC certification.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
Industry Canada
Note: The term "IC" before the radio certification number signifies that
Industry Canada technical specifications were met.
Products that show an Industry Canada identifier on the product label (IC
HiveAP 170, 320, 330, 340, 350, BR100, BR200 and BR200-WP) can be operated
in Canada under the following restrictions:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
• Reorient or relocate the receiving antenna
IC Radiation Exposure Statement
• Increase the separation between the equipment and receiver
Radiation Exposure Statement: This equipment complies with IC radiation
exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20 cm between
the radiator and your body, if using AP170 directional antenna (part number
AH-ACC-170-ANT-18) the distance is 65cm.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
In compliance with FCC Part 15 regulations, the HiveAP automatically
discontinues transmission if there is no valid information to transmit or if there
is an operational failure.
Important: FCC Regulatory Warning Notices
HiveAP 110, 120, 320, 330, 340, 350, BR100 devices are restricted to indoor
use due to their operation in 5 GHz frequencies, which are shared by mobile
satellite systems and government radar systems. The FCC requires that these
products only be used indoors to reduce the potential for harmful interference
with co-channel radar that might be operating in the 5.25-5.35 or 5.47-5.725
GHz frequency ranges in the same area. The conflicting activity of radar
stations and these devices can cause interference or damage to each other. In
addition, these devices have a radar detection function that might interrupt
normal operations when they detect a radar signal. To reduce the risk of
interference even further, installing these devices away from windows is
recommended.
HiveAP devices operating within the 5.15-5.25 GHz frequency range are
restricted to indoor environments.
The FCC region code is set in the device during the manufacturing process, the
option to set it to any region other than FCC is disabled, and the country code
selection function has been completely removed from all U.S. models. It is
impossible for the end user to change the region to anything other than FCC.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20 centimeters (8 inches) between the radiator
and your body if using AP170 directional antenna (part number
AH-ACC-170-ANT-18) the distance is 65cm. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
© 2011 Aerohive Networks, Inc. All rights reserved.
For the models using “detachable Antenna”
The HiveAP 170/350 has been designed to operate with an antenna having a
Dipole maximum gain 5dBi. Antenna having a higher gain is strictly prohibited
per regulations of Industry Canada. The required antenna impedance is 50
ohms.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (E.I.R.P) is not more than that
necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with
the antenna types listed below with the maximum permissible gain and
required antenna impedance for each antenna type indicated. Antenna types
not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
: Dipole/5dBi
For the models supporting 5GHz frequencies
Caution: The device for the band 5150-5250 MHz is only for indoor usage to
reduce potential for harmful interference to co-channel mobile satellite
systems.
High power radars are allocated as primary users (meaning they have priority)
of 5250-5350 MHz and 5650-5850 MHz and these radars could cause
interference and/or damage to LE-LAN devices.
The band from 5600-5650 MHz will be disabled by the proprietary software
during the manufacturing and which cannot be changed by the end user.
Pour le modèle à l'aide antanna Détachables
Note: Le terme “IC” précédant le numéro de certification radio signifie que les
spécifications techniques de l’Industrie du Canada ont été respectées.
330033-12 Rev. B
Aerohive HiveAP Compliance Information
Les produits indiquant un identifiant d’Industrie du Canada sur leur étiquette
(IC: 7774A-HiveAP170) peuvent être exploités au Canada dans le cadre des
restrictions suivantes:
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada
applicable aux appareils radio exempts de licence. Son fonctionnement est
sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de
brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage
reçu, y compris un brouillage susceptible de provoquer un fonctionnement
indésirable.
NOTE IMPORTANTE:
Déclaration d'exposition aux radiations: Cet équipement est conforme
aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et
utilisé avec un minimum de 20 cm de distance entre la source de
rayonnement et votre corps.
Le point d’accès HiveAP170 a été conçu pour fonctionner avec une Dipole
antenne ayant un gain maximal de dBi 5. Une antenne à gain plus élevé est
strictement interdite par les règlements d'Industrie Canada. L'impédance
d'antenne requise est de 50 ohms.
Conformément à la réglementation d'Industrie Canada, le présent émetteur
radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou
inférieur) approuvé pourl'émetteur par Industrie Canada. Dans le but de
réduire les risques de brouillage radioélectriqueà l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que
lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire àl'établissement d'une communication satisfaisante.
Le présent émetteur radio (IC: 7774A-HIVEAP170 / Model: HiveAP 1700) a été
approuvé par Industrie Canada pour fonctionner avec les types d'antenne
énumérés ci-dessous et ayant un gain admissible maximal et l'impédance
requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette
liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement
interdits pour l'exploitation de l'émetteur.
Avertissement: Le dispositif fonctionnant dans la bande 5150-5250 MHz les
risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant
les mêmes canaux.
Pour le modèle de fréquences 5GHz
Les utilisateurs de radars de haute puissance sont désignés utilisateurs
principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et
5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des
dommages aux dispositifs LAN-EL.
La bande de frequence de 5600-5650MHz devra etre desactivee par logiciel
lors de la conception et ne devra comporter aucune possibilite de modification
par l'utilisateur final.
• EN 301 489-1 / EN 301 489-17 - EMC requirements for radio equipment
The HiveAP 170, 330, and 350 platforms comply with the essential
requirements of the R&TTE Directive 1999/5/EC. The following test methods
have been applied to prove presumption of conformity with the essential
requirements of the R&TTE Directive 1999/5/EC:
• EN 60950-1:2006+A11:2009+A1:2010
Safety of Information Technology Equipment
• EN 50385: 2002
Generic standard to demonstrate the compliance of electronic and
electrical apparatus with the basic restrictions related to human
exposure to electromagnetic fields (0 Hz - 300 GHz)
• EN 300 328 V1.7.1: 2006
Electromagnetic compatibility and Radio spectrum Matters (ERM);
Wideband Transmission systems; Data transmission equipment operating
in the 2.4 GHz ISM band and using spread spectrum modulation
techniques; Harmonized EN covering essential requirements under article
3.2 of the R&TTE Directive
• EN 301 893 V1.5.1: 2008
Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN;
Harmonized EN covering essential requirements of article 3.2 of the
R&TTE Directive
• EN 301 489-1 V1.8.1: 2008
Electromagnetic Compatibility and Radio Spectrum Matters (ERM);
Electromagnetic Compatibility (EMC) standard for radio equipment and
services; Part 1: Common technical requirements
• EN 301 489-17 V2.1.1: 2009
Electromagnetic Compatibility and Radio spectrum Matters (ERM);
Electromagnetic Compatibility (EMC) standard for radio equipment and
services; Part 17: Specific conditions for 2.4 GHz wideband transmission
systems and 5 GHz high performance RLAN equipment
The HiveAP 170, 330, and 350 are 5 GHz wideband transmission systems
(transceivers), intended for use in all EU member states and EFTA countries,
except in France and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum
authorities in order to obtain authorization to use this equipment for setting
up outdoor radio links and/or for supplying public access to
telecommunications and/or network services.
These devices may not be used for setting up outdoor radio links in France and
in some areas the RF output power may be limited to 10 mW EIRP in the
frequency range of 2454–2483.5 MHz For detailed information the end-user
should contact the national spectrum authority in France.
Declarations of conformity, compliance statements, and other regulatory
documentation are available at www.aerohive.com/support.
Wi-Fi Certification
The Wi-Fi CERTIFIED™ Logo is a certification mark of the Wi-Fi Alliance®. The
HiveAP 20, 100, 300 series have been certified for WPA™, WPA2™, WMM® (Wi-Fi
Multimedia™), WMM Power Save, IEEE 802.11d, IEEE 802.11h, and the
following types of EAP (Extensible Authentication Protocol):
• EAP-TLS
• EAP-SIM
• EAP-TTLS/MSCHAPv2
• EAP-AKA
• PEAPv0/EAP-MSCHAPv2
• EAP-FAST
WEEE and RoHS Compliance
Aerohive Networks products have been reviewed, analyzed and found to be in
compliance with the European Union (EU) directive for Waste Electrical and
Electronic Equipment (WEEE) and with the EU directive for the Restriction of
Hazardous Substances (RoHS).
WEEE Collection Programs in the U.S. and EU
• PEAPv1/EAP-GTC
The HiveAP 100 and 300 series have also been certified for short guard interval
and 40-MHz operation in the 5-GHz band.
EC Conformance Declaration
Marking by the above symbol indicates compliance with the Essential
Requirements of the R&TTE Directive of the European Union (1999/5/EC). The
HiveAP 110, 120, 320, and 340 platforms meet the following conformance
standards:
At end of life, customers are requested to contact Aerohive to make
arrangements for WEEE collection of their products. The Aerohive collection
center in the U.S. is at the following address:
Aerohive Inc.
330 Gibraltar Drive
Sunnyvale, CA 94089
Telephone: 408-510-6100
Contact: Technical Support, weee@aerohive.com
Aerohive, in association with M-Cubed LLC, also has a collection center at the
following address in Germany, a member state of the European Union:
EXTRABYTE - M Cubed LLC
Klopstock Strasse #8
33613 BIELEFELD
Telephone: 49-521-882245
Contact: Mr. Andreas Budde
• EN 60950-1 (IEC 60950-1) 2nd edition - Product Safety
• EN 301 893 - Technical requirements for 5 GHz radio equipment
• EN 300 328 - Technical requirements for 2.4 GHz radio equipment
© 2011 Aerohive Networks, Inc. All rights reserved.
330033-12 Rev. B
Aerohive HiveAP Compliance Information
Countries of Operation and Conditions
of Use in the European Community
HiveAPs are intended to be operated in all countries of the European
Community. Requirements for indoor vs. outdoor operation, license
requirements and allowed channels of operation apply in some countries as
described below.
• Before operating a HiveAP, the admin or installer must properly enter the
current country code as described in Aerohive product documentation.
Note to U.S. model owners: To comply with U.S. FCC regulations, the
country selection function has been completely removed from all U.S.
models. The above function is for non-U.S. models only.
• HiveAPs automatically limit the allowable channels determined by the
current country of operation. Incorrectly entering the country of
operation might result in illegal operation and cause harmful
interference to other systems. The admin is obligated to ensure HiveAPs
are operating according to the channel limitations, indoor/outdoor
restrictions and license requirements for each European Community
country as described in this section.
• HiveAPs can be operated indoors or outdoors in all countries of the
European Community using the 2.4 GHz band: Channels 1-13, except
where noted below:
Declaration of Conformity in Languages
of the European Community
Czech
Aerohive tímto prohlašuje, že tento Radio LAN device
je ve shodě se základními požadavky a dalšími
příslušnými ustanoveními směrnice 1999/5/ES.
Danish
Undertegnede Aerohive erklærer herved, at følgende
udstyr Radio LAN device overholder de væsentlige krav
og øvrige relevante krav i direktiv 1999/5/EF.
Dutch
Hierbij verklaart Aerohive dat het toestel Radio LAN
device in overeenstemming is met de essentiële eisen
en de andere relevante bepalingen van richtlijn
1999/5/EG.
English
Hereby, Aerohive, declares that this Radio LAN device
is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
Estonian
– In Italy and Luxembourg, you must apply for a license from the
national spectrum authority to operate a HiveAP outside your own
premises and for public use or service.
– In Belgium outdoor operation is only permitted using the 2.46 to
2.4835 GHz band: Channel 13.
– In France outdoor operation is limited to the 2.454 to 2.4835 GHz band
(channels 8 to 13) at a maximum of 10 mW EIRP (effective isotropic
radiated power).
Finnish
Valmistaja Aerohive vakuuttaa täten että Radio LAN
device tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä koskevien direktiivin
muiden ehtojen mukainen.
French
Par la présente Aerohive déclare que cet appareil Radio
LAN device est conforme aux exigences essentielles et
aux autres dispositions relatives à la directive
1999/5/CE.
German
Hiermit erklärt Aerohive, dass sich dieses Radio LAN
device in Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten
Vorschriften der Richtlinie 1999/5/EG befindet".
(BMWi)
– In Norway, the 2.4 GHz band cannot be used outdoors within a 20-km
radius of the center of Ny-Ålesund.
– In Russia, the 2.4 GHz band is for indoor use only.
• Because radar systems use some bands in the 5 GHz spectrum, WLAN
devices operating in these bands must use DFS (Dynamic Frequency
Selection) to detect radar activity and switch channels automatically to
avoid interfering with radar operations. For the ETSI region, the HiveAP
300 series is certified for the latest ETSI EN 301 893 v1.5.1 DFS
requirements and can use DFS channels 52 to 140 (5.26 GHz to 5.32 GHz,
and 5.5 GHz to 5.7 GHz). To comply with ETSI regulations when deploying
a HiveAP 300 series device outdoors, set the 5 GHz radio to operate on
the DFS channels and enable DFS. When deploying a HiveAP 300 series
device indoors, then the 5 GHz radio can also use channels 36 to 48 as
well as the DFS channels. The maximum transmit power for channels
from 36 to 48 are 17dBm in the ETSI region. Because this maximum is
enforced by HiveOS, the HiveAP automatically limits the power to 17 dBm
even if the setting is greater than that.
• The availability of some specific channels and/or operational frequency
bands are country dependent and are firmware programmed at
installation to match the intended destination. The firmware setting is
accessible by the end user. Some national restrictions are noted below:
– In Italy and Luxembourg, you must apply for a license from the
national spectrum authority to operate a HiveAP outside your own
premises and for public use or service in the 5.15 to 5.35 GHz band
(channels 36 to 64) and 5.47 to 5.725 GHz band (channels 100 to 140).
– In Russia, you can only use the 5.15 to 5.35 GHz band at 100 mW (20
dBm) indoors, in closed industrial and warehouse areas, and on board
aircraft for local network and crew communications during all stages
of a flight and for public WLAN access only at an altitude of 3000
meters or higher. You can only use the 5.65 to 5.825 GHz band with
100 mW EIRP on board aircraft at an altitude of 3000 meters or higher.
© 2011 Aerohive Networks, Inc. All rights reserved.
Käesolevaga kinnitab Aerohive seadme Radio LAN
device vastavust direktiivi 1999/5/EÜ põhinõuetele ja
nimetatud
direktiivist
tulenevatele
teistele
asjakohastele sätetele.
Greek
Hungarian
Alulírott, Aerohive nyilatkozom, hogy a Radio LAN
device megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb
elõírásainak.
Italian
Con la presente Aerohive dichiara che questo Radio LAN
device è conforme ai requisiti essenziali ed alle altre
disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
Latvian
Ar šo Aerohive deklarē, ka Radio LAN device atbilst
Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar
to saistītajiem noteikumiem.
Lithuanian
Šiuo Aerohive deklaruoja, kad šis Radio LAN device
atitinka esminius reikalavimus ir kitas 1999/5/EB
Direktyvos nuostatas.
Maltese
Hawnhekk, Aerohive, jiddikjara li dan Radio LAN device
jikkonforma mal-ħtiġijiet essenzjali u ma
provvedimenti oħrajn relevanti li hemm fid-Dirrettiva
1999/5/EC.
Polish
Niniejszym Aerohive oświadcza, że Radio LAN device
jest zgodne z zasadniczymi wymogami oraz pozostałymi
stosownymi postanowieniami Dyrektywy 1999/5/EC.
Portuguese
Aerohive declara que este Radio LAN device está
conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
330033-12 Rev. B
Aerohive HiveAP Compliance Information
Slovenian
Aerohive izjavlja, da je ta Radio LAN device v skladu z
bistvenimi zahtevami in ostalimi relevantnimi določili
direktive 1999/5/ES.
Spanish
Por medio de la presente Aerohive declara que el Radio
LAN device cumple con los requisitos esenciales y
cualesquiera otras disposiciones aplicables o exigibles
de la Directiva 1999/5/CE.
Swedish
Härmed intygar Aerohive att denna Radio LAN device
står I överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som
framgår av direktiv 1999/5/EG.
HiveAP Safety Compliance
Power Cord Safety
Please read the following safety information carefully before installing a
HiveAP.
Warning: Installation and removal of HiveAPs must be carried out by qualified
personnel only.
• HiveAPs must be connected to an earthed (grounded) outlet to comply
with international safety standards.
• Do not connect HiveAPs to an A.C. outlet (power supply) without an earth
(ground) connection.
Europe
The supply plug must comply with CEE7/7 ("SCHUKO").
The mains cord must be  or  marked and
be of type HO3VVF3GO.75 (minimum).
IEC-320 receptacle.
Veuillez lire attentivement les informations de sécurité relatives à
l'installation d'un point d'accès HiveAP.
Avertissement: L'installation et la dépose de points d'accès HiveAP doivent
être effectuées uniquement par un personnel qualifié.
• Les points d'accès HiveAP doivent être connectés sur le secteur par une
prise électrique munie de terre (masse) afin de respecter les standards
internationaux de sécurité.
• Ne jamais connecter des points d'accès HiveAP à une alimentation
électrique non-pourvue de terre (masse).
• Le boitier d'alimentation (connecté directement au point d'accès) doit
être compatible avec une entrée électrique de type EN 60320/IEC 320.
• La prise secteur doit se trouver à proximité du point d'accès HiveAP et
facilement accessible. Vous ne pouvez mettre hors tension un point
d'accès HiveAP qu'en débranchant son alimentation électrique au niveau
de cette prise.
• The appliance coupler (the connector to the unit and not the wall plug)
must have a configuration for mating with an EN 60320/IEC 320 appliance
inlet.
• Pour des raisons de sécurité, le point d'accès HiveAP fonctionne à une
tension extrêmement basse, conformément à la norme IEC 60950. Les
conditions de sécurité sont valables uniquement si l'équipement auquel
le point d'accès HiveAP est raccordé fonctionne également selon cette
norme.
• The socket outlet must be near the HiveAP and easily accessible. You can
only remove power from a HiveAP by disconnecting the power cord from
the outlet.
• Un point d'accès HiveAP alimenté par son interface réseau Ethernet en
mode POE (Power over Ethernet) doit être physiquement dans le même
bâtiment que l'équipement réseau qui lui fournit l'électricité.
• HiveAPs operate under SELV (Safety Extra Low Voltage) conditions
according to IEC 60950. The conditions are only maintained if the
equipment to which they are connected also operates under SELV
conditions.
• A HiveAP receiving power through its PoE (Power over Ethernet) interface
must be in the same building as the equipment from which it receives
power.
France et Pérou uniquement:
Un point d'accès HiveAP ne peut pas être alimenté par un dispositif à
impédance à la terre. Si vos alimentations sont du type impédance à la terre,
alors le point d'accès HiveAP doit être alimenté par une tension de 230 V
(2P+T) via un transformateur d'isolement à rapport 1:1, avec le neutre
connecté directement à la terre (masse).
France and Peru only:
Cordon électrique - Il doit être agréé dans le pays d'utilisation
HiveAPs cannot be powered from IT* supplies. If your supplies are of IT type,
then a HiveAP must be powered by 230 V (2P+T) via an isolation transformer
ratio 1:1, with the secondary connection point labelled Neutral, connected
directly to earth (ground). *Impédance à la terre
Etats-Unis
et Canada
Les spécifications minimales pour un cable flexible
- AWG No. 18, ou AWG No. 16 pour un cable de longueur
inférieure à 2 mètres.
- Type SV ou SJ
- 3 conducteurs
Important! Before making connections, make sure you have the correct cord
set. Check it (read the label on the cable) against the description in this
section.
Power Cord Set
U.S.A.
and Canada
Le cordon doit être en mesure d'acheminer un courant
nominal d'au moins 10 A.
The cord set must be UL/CSA/NRTL approved and
certified.
Minimum specifications for the flexible cord:
- No. 18 AWG not longer than 2 meters, or 16 AWG
- Type SV or SJ
- 3-conductor
The cord set must have a rated current capacity of at
least 10 A.
The attachment plug must be an earth-grounding type
with NEMA 5-15P (15 A, 125 V) or NEMA 6-15 (15 A, 250
V) configuration.
Le cordon doit avoir reçu l'homologation des UL et un
certificat de la CSA.
La prise femelle de branchement doit être du type à mise à
la terre (mise à la masse) et respecter la configuration
NEMA 5-15P (15 A, 125 V) ou NEMA 6-15P (15 A, 250 V).
Danemark
La prise mâle d'alimentation doit respecter la section 107-2
D1 de la norme DK2 1a ou DK2 5a.
Suisse
La prise mâle d'alimentation doit respecter la norme
SEV/ASE 1011.
Europe
La prise secteur doit être conforme aux normes CEE 7/7
("SCHUKO").
LE cordon secteur doit porter la mention  ou 
et doit être de type HO3VVF3GO.75 (minimum).
Denmark
The supply plug must comply with Section 107-2-D1,
Standard DK2-1a or DK2-5a.
Switzerland
The supply plug must comply with SEV/ASE 1011.
Bitte unbedingt vor dem Einbauen
Sicherheitsanweisungen durchlesen.
U.K.
The supply plug must comply with BS1363 (3-pin 13 A)
and be fitted with a 5 A fuse that complies with BS1362.
Warnung: Die Installation und der Ausbau des Geräts darf nur durch
Fachpersonal erfolgen.
The mains cord must be  or  marked and
be of type HO3VVF3GO.75 (minimum).
• Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose
angeschlossen werden.
© 2011 Aerohive Networks, Inc. All rights reserved.
des
HiveAP
die
folgenden
• Das Gerät muß an eine geerdete Steckdose angeschlossen werden,
welche die internationalen Sicherheitsnormen erfüllt.
330033-12 Rev. B
Aerohive HiveAP Compliance Information
• Der Gerätestecker (der Anschluß an das Gerät, nicht
Wandsteckdosenstecker) muß einen gemäß EN 60320/IEC
konfigurierten Geräteeingang haben.
der
320
• Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein.
Die Stromversorgung des Geräts kann nur durch Herausziehen des
Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.
• Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen
(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind
nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter
SELV-Bedingungen betrieben werden.
Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft
werden:
U.S.A.
und
Kanada
Der Cord muß das UL gepruft und war das CSA beglaubigt.
Das Minimum spezifikation fur der Cord sind:
- Nu. 18 AWG - nicht mehr als 2 meter, oder 16 AWG.
- Der typ SV oder SJ
- 3-Leiter
Der Cord muß haben eine strombelastbarkeit aus wenigstens 10
A.
Dieser Stromstecker muß hat einer erdschluss mit der typ NEMA
5-15P (15A, 125V) oder NEMA 6-15P (15A, 250V) konfiguration.
Danemark
Dieser Stromstecker muß die ebene 107-2-D1, der standard
DK2-1a oder DK2-5a Bestimmungen einhalten.
Ce produit est destine a un usage specifique et doit etre installe par un
personnel qualifie maitrisant les radiofrequences et les regles s'y
rapportant. L'installation et les reglages ne doivent pas etre modifies par
l'utilisateur final.
2. Emplacement d'installation
En usage normal, afin de respecter les exigences reglementaires
concernant l'exposition aux radiofrequences, ce produit doit etre installe
de facon a respecter une distance de 40 cm entre l'antenne emettrice et
les personnes.
3. Antenn externe.
Utiliser uniiquement les antennes approuvees par le fabricant.
L'utilisation d'autres antennes peut conduire a un niveau de rayonnement
essentiel ou non essentiel depassant les niveaux limites definis par
FCC/IC, ce qui est interdit.
4. Procedure d'installation
Consulter le manuel d'installation.
5. Avertissement
Choisir avec soin la position d'installation et s'assurer que la puissance de
sortie ne depasse pas les limites en vigueur. La violation de cette regle
peut conduire a de serieuses penalites federales.
Korean ;
‘당해 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는
할 수 없음“
Country Certification Statements
The following HiveAPs have been certified by the specified regulatory agencies
and authorities:
Schweiz
Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen
einhalten.
HiveAP 170
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0077814/11
Dealer number: DA0070080/11
Europe
Europe Das Netzkabel muß vom Typ HO3VVF3GO.75
(Mindestanforderung) sein und die Aufschrift  oder
 tragen.
Der Netzstecker muß die Norm CEE 7/7 erfüllen ("SCHUKO").
HiveAP 330
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0072051/11
Dealer number: DA0070080/11
HiveAP 170 Professional Installation Requirement
Please be advised that due to the unique function supplied by this product, the
device is intended for use with Aerohive software and licensed third-party
software only. The product will be distributed through controlled distribution
channels, installed by trained professionals, and will not be sold directly to the
general public through retail stores.
1. Installation personal
This product is designed for a specific application and must be installed
by qualified personnel with RF and related rule knowledge. The general
user shall not attempt to install or change the device settings.
2. Installation location
To meet regulatory RF exposure requirements, the product shall be
installed at a location where the radiating antenna in normal operating
conditions can be kept at least 20cm from people.
3. External antenna
Use only antennas which have been approved by Aerohive Networks, Inc.
Non-approved antennas may produce unwanted spurious or excessive RF
transmission, which is prohibited, and may violate the FCC/IC limit.
4. Installation procedure
Please refer to installation manual for details.
5. Warning
Please carefully select the installation position and make sure that the
final power output does not exceed the allowed limit. Violation of this
limit could lead to serious federal penalties.
HiveAP 170 Instructions d'installation professionnelle
Veuillez noter que l'appareil etant dedie a une fonction unique, il doit etre
utilise avec Aerohive logiciel proprietaire. Ce produit sera propose par un
reseau de distribution controle et installe par des professionels; il ne sera pas
propose au grand public par le reseau de la grande distribution.
1. Installation
© 2011 Aerohive Networks, Inc. All rights reserved.
Mexico: Cofetel Cert. Number: RCPAEHI11-0892-A1 (valid 11/23/2012)
China: SRRC: CMIIT: 2011AJ7102
Hong Kong: OFTA: Certificate No: HK0011200428
HiveAP 350
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0081235/12
Dealer number: DA0070080/11
Mexico: Cofetel Cert. Number: RCPAEHI11-0892 (valid 11/23/2012)
China: SRRC: CMIIT: 2011AJ7101
BR100:
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0070180/11
Dealer number: DA0070080/11
HiveAP 340
Saudi Arabia: Product Conformity Programme (PCP)
Registration Number: KSA R-103282
Communications and Information Technology Commission (CITC)
Number: 14408
HiveAP 320
Mexico: Cofetel Certification Number: RCPAEHI10-1206
NYCE/NOM Certification Number: 1002CE11218
HiveAP 120
UAE: Telecommunication Regulatory Authority (TRA)
Registration Number: ER0070180/11
Dealer number: DA0070080/11
Malaysia: SIRIM Type Approval Code: RAVG/92M/1010/S (10-1784)
Singapore: Infocomm Development Authority (IDA)
Registration Number: G1901-10
Saudi Arabia: Product Conformity Programme (PCP)
Registration Number: KSA R-103282
Communications and Information Technology Commission (CITC)
Number: 14405
China: SRRC: CMIIT: 2011AJ6593
330033-12 Rev. B
Aerohive HiveAP Compliance Information
Liability Disclaimer
Installation of Aerohive equipment must comply with local and national
electrical codes and with other regulations governing this type of installation.
Aerohive Networks, its channel partners, resellers, and distributors assume no
liability for personal injury, property damage, or violation of government
regulations that might arise from failing to comply with the instructions
provided and appropriate electrical codes.
© 2011 Aerohive Networks, Inc. All rights reserved.
330033-12 Rev. B

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : csaleem
Create Date                     : 2012:03:29 11:43:06-07:00
Modify Date                     : 2012:03:29 11:43:06-07:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : csaleem
Title                           : Microsoft Word - Aerohive_Compliance
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.5.0 (Windows)
Document ID                     : uuid:46e2db40-2a3e-4b3b-851f-8527fcae4a6d
Instance ID                     : uuid:c4828a22-c472-4d7f-9446-d3a474a7dce1
Page Count                      : 6

EXIF Metadata provided by EXIF.tools