Aerohive Networks HIVEAP320DFS 802.11a/b/g/n access point User Manual

Aerohive Networks, Inc. 802.11a/b/g/n access point

Contents

User manual

1Aerohive Deployment GuideFor HiveAP and HiveManager DevicesAerohive Technical PublicationsCopyright NoticeCopyright © 2009 Aerohive Networks, Inc. All rights reserved.Aerohive Networks, the Aerohive Networks logo, HiveOS, HiveAP, and HiveManager are trademarks of Aerohive Networks, Inc. All other trademarks and registered trademarks are the property of their respective companies.Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without receiving written permission from:Aerohive Networks, Inc.3150-C Coronado DriveSanta Clara, CA 95054P/N 330002-06, Rev. A
Deployment Guide 3HIVEAP COMPLIANCE INFORMATIONThe availability of some specific channels and/or operationalfrequency bands are country dependent and are firmwareprogrammed at the factory to match the intended destination.The firmware setting is not accessible by the end user.• The 5 GHz Turbo Mode feature is not allowed for operation in anyEuropean Community country. You can find the current setting forthis feature in two places. In the HiveManager GUI, clickConfiguration > Network Objects>  Radio Profiles > profile >Advanced. In the HiveAP CLI, enter this command: show radioprofile profile. By default, Turbo Mode is disabled.Declaration of Conformity in Languages of the European CommunityHiveAP 20 ag Safety CompliancePower Cord SafetyPlease read the following safety information carefully before installinga HiveAP.Warning: Installation and removal of HiveAPs must be carried out byqualified personnel only.• HiveAPs must be connected to an earthed (grounded) outlet tocomply with international safety standards.• Do not connect HiveAPs to an A.C. outlet (power supply) withoutan earth (ground) connection.• The appliance coupler (the connector to the unit and not the wallplug) must have a configuration for mating with an EN 60320/IEC320 appliance inlet.• The socket outlet must be near the HiveAP and easily accessible.You can only remove power from a HiveAP by disconnecting thepower cord from the outlet.• HiveAPs operate under SELV (Safety Extra Low Voltage) conditionsaccording to IEC 60950. The conditions are only maintained if theequipment to which they are connected also operates under SELVconditions.• A HiveAP receiving power through its PoE (Power over Ethernet)interface must be in the same building as the equipment fromwhich it receives power.France and Peru only:HiveAPs cannot be powered from IT* supplies. If your supplies are of ITtype, then a HiveAP must be powered by 230 V (2P+T) via an isolationtransformer ratio 1:1, with the secondary connection point labelledNeutral, connected directly to earth (ground).* Impédance à la terreImportant! Before making connections, make sure you have the correctcord set. Check it (read the label on the cable) against the descriptionon the following page.Veuillez lire attentivement les informations de sécurité relatives àl'installation d'un point d'accès HiveAP.English Hereby, Edgecore, declares that this Radio LANdevice is in compliance with the essentialrequirements and other relevant provisions ofDirective 1999/5/EC.Finnish Valmistaja Edgecore vakuuttaa täten että Radio LANdevice tyyppinen laite on direktiivin 1999/5/EYoleellisten vaatimusten ja sitä koskevien direktiivinmuiden ehtojen mukainen.Dutch Hierbij verklaart Edgecore dat het toestel RadioLAN device in overeenstemming is met deessentiële eisen en de andere relevante bepalingenvan richtlijn 1999/5/EG.Bij deze Edgecore dat deze Radio LAN devicevoldoet aan de essentiële eisen en aan de overigerelevante bepalingen van Richtlijn 1999/5/EC.French Par la présente Edgecore déclare que cet appareilRadio LAN est conforme aux exigences essentielleset aux autres dispositions relatives à la directive1999/5/CE.Swedish Härmed intygar Edgecore att denna Radio LANdevice står I överensstämmelse med de väsentligaegenskapskrav och övriga relevanta bestämmelsersom framgår av direktiv 1999/5/EG.Danish Undertegnede Edgecore erklærer herved, atfølgende udstyr Radio LAN device overholder devæsentlige krav og øvrige relevante krav i direktiv1999/5/EF.German Hiermit erklärt Edgecore, dass sich dieser/diese/dieses Radio LAN device in Übereinstimmung mitden grundlegenden Anforderungen und den anderenrelevanten Vorschriften der Richtlinie 1999/5/EGbefindet". (BMWi)Hiermit erklärt Edgecore die Übereinstimmung desGerätes Radio LAN device mit den grundlegendenAnforderungen und den anderen relevantenFestlegungen der Richtlinie 1999/5/EG. (Wien)GreekItalian Con la presente Edgecore dichiara che questo RadioLAN device è conforme ai requisiti essenziali ed allealtre disposizioni pertinenti stabilite dalla direttiva1999/5/CE.Spanish Por medio de la presente Manufacturer declara queel Radio LAN device cumple con los requisitosesenciales y cualesquiera otras disposicionesaplicables o exigibles de la Directiva 1999/5/CE.Portuguese Manufacturer declara que este Radio LAN deviceestá conforme com os requisitos essenciais e outrasdisposições da Directiva 1999/5/CE.Power Cord SetU.S.A. and Canada The cord set must be UL-approved and CSA certified.Minimum specifications for the flexible cord:- No. 18 AWG not longer than 2 meters, or 16 AWG- Type SV or SJ- 3-conductorThe cord set must have a rated current capacity of at least 10 A.The attachment plug must be an earth-grounding type with NEMA 5-15P (15 A, 125 V) or NEMA 6-15 (15 A, 250 V) configuration.Denmark The supply plug must comply with Section 107-2-D1, Standard DK2-1a or DK2-5a.Switzerland The supply plug must comply with SEV/ASE 1011.U.K. The supply plug must comply with BS1363 (3-pin 13 A) and be fitted with a 5 A fuse that complies with BS1362.The mains cord must be <HAR> or <BASEC> marked and be of type HO3VVF3GO.75 (minimum).Europe The supply plug must comply with CEE7/7 ("SCHUKO").The mains cord must be <HAR> or <BASEC> marked and be of type HO3VVF3GO.75 (minimum).IEC-320 receptacle.
HiveAP Compliance Information4AerohiveAvertissement: L'installation et la dépose de points d'accès HiveAPdoivent être effectuées uniquement par un personnel qualifié.• Les points d'accès HiveAP doivent être connectés sur le secteurpar une prise électrique munie de terre (masse) afin de respecterles standards internationaux de sécurité.• Ne jamais connecter des points d'accès HiveAP à une alimentationélectrique non-pourvue de terre (masse).• Le boitier d'alimentation (connecté directement au point d'accès)doit être compatible avec une entrée électrique de type EN60320/IEC 320.• La prise secteur doit se trouver à proximité du point d'accèsHiveAP et facilement accessible. Vous ne pouvez mettre horstension un point d'accès HiveAP qu'en débranchant sonalimentation électrique au niveau de cette prise.• Pour des raisons de sécurité, le point d'accès HiveAP fonctionne àune tension extrêmement basse, conformément à la norme IEC60950. Les conditions de sécurité sont valables uniquement sil'équipement auquel le point d'accès HiveAP est raccordéfonctionne également selon cette norme.• Un point d'accès HiveAP alimenté par son interface réseauEthernet en mode POE (Power over Ethernet) doit êtrephysiquement dans le même bâtiment que l'équipement réseauqui lui fournit l'électricité.France et Pérou uniquement:Un point d'accès HiveAP ne peut pas être alimenté par un dispositif àimpédance à la terre. Si vos alimentations sont du type impédance à laterre, alors le point d'accès HiveAP doit être alimenté par une tensionde 230 V (2P+T) via un transformateur d'isolement à rapport 1:1, avecle neutre connecté directement à la terre (masse).Bitte unbedingt vor dem Einbauen des HiveAP die folgendenSicherheitsanweisungen durchlesen.Warnung: Die Installation und der Ausbau des Geräts darf nur durchFachpersonal erfolgen.• Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdoseangeschlossen werden.• Das Gerät muß an eine geerdete Steckdose angeschlossen werden,welche die internationalen Sicherheitsnormen erfüllt.• Der Gerätestecker (der Anschluß an das Gerät, nicht derWandsteckdosenstecker) muß einen gemäß EN 60320/IEC 320konfigurierten Geräteeingang haben.• Die Netzsteckdose muß in der Nähe des Geräts und leichtzugänglich sein. Die Stromversorgung des Geräts kann nur durchHerausziehen des Gerätenetzkabels aus der Netzsteckdoseunterbrochen werden.• Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungensind nur gegeben, wenn auch die an das Gerät angeschlossenenGeräte unter SELV-Bedingungen betrieben werden.Liability DisclaimerInstallation of Aerohive equipment must comply with local and national electrical codes and with other regulations governing this type of installation.Aerohive Networks, its channel partners, resellers, and distributors assume no liability for personal injury, property damage, or violation ofgovernment regulations that may arise from failing to comply with the instructions in this guide and appropriate electrical codes.Cordon électrique - Il doit être agréé dans le pays d'utilisationEtats-Unis et Canada Le cordon doit avoir reçu l'homologation des UL et un certificat de la CSA.Les spécifications minimales pour un cable flexible- AWG No. 18, ou AWG No. 16 pour un cable delongueur inférieure à 2 mètres.- Type SV ou SJ- 3 conducteursLe cordon doit être en mesure d'acheminer un courant nominal d'au moins 10 A.La prise femelle de branchement doit être du type à mise à la terre (mise à la masse) et respecter la configuration NEMA 5-15P (15 A, 125 V) ou NEMA 6-15P (15 A, 250 V).Danemark La prise mâle d'alimentation doit respecter la section 107-2 D1 de la norme DK2 1a ou DK2 5a.Suisse La prise mâle d'alimentation doit respecter la norme SEV/ASE 1011.Europe La prise secteur doit être conforme aux normes CEE 7/7 ("SCHUKO").LE cordon secteur doit porter la mention <HAR> ou <BASEC> et doit être de type HO3VVF3GO.75 (minimum).Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden:U.S.A. undKanadaDer Cord muß das UL gepruft und war das CSA beglaubigt.Das Minimum spezifikation fur der Cord sind:- Nu. 18 AWG - nicht mehr als 2 meter, oder 16 AWG.- Der typ SV oder SJ- 3-LeiterDer Cord muß haben eine strombelastbarkeit aus wenigstens 10 A.Dieser Stromstecker muß hat einer erdschluss mit der typ NEMA 5-15P (15A, 125V) oder NEMA 6-15P (15A, 250V) konfiguration.Danemark Dieser Stromstecker muß die ebene 107-2-D1, der standard DK2-1a oder DK2-5a Bestimmungen einhalten.Schweiz Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen einhalten.Europe Europe Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestanforderung) sein und die Aufschrift <HAR> oder <BASEC> tragen.Der Netzstecker muß die Norm CEE 7/7 erfüllen ("SCHUKO").
Deployment Guide 25Chapter 2 The HiveAP 20 ag PlatformThe Aerohive HiveAP 20 ag is a new generation wireless access point. HiveAPs have the unique ability to self-organize and coordinate with each other, creating a distributed-control WLAN solution that offers greater mobility, security, quality of service, and radio control.This guide combines product information, installation instructions, and configuration examples for both the HiveAP and HiveManager platforms. This chapter covers the following topics relating to the HiveAP:• "HiveAP 20 Product Overview" on page 26• "Ethernet and Console Ports" on page 28• "Status LEDs" on page 29• "Antennas" on page 30• "Mounting the HiveAP 20" on page 31• "Device, Power, and Environmental Specifications" on page 33
Chapter 2 The HiveAP 20 ag Platform26 AerohiveHIVEAP 20 PRODUCT OVERVIEWThe HiveAP 20 ag is a multi-channel wireless AP (access point). It is compatible with IEEE 802.11b/g (2.4 GHz) and IEEE 802.11a (5 GHz) standards and supports a variety of Wi-Fi (wireless fidelity) security protocols, including WPA (Wi-Fi Protected Access) and WPA2.You can see the hardware components on the HiveAP in Figure 1. Each component is described in Table 1.Figure 1  HiveAP 20 Hardware ComponentsTable 1  HiveAP 20 Component DescriptionsComponent DescriptionFixed Dual-Band Antennas The two fixed omnidirectional dipole antennas can operate at two radio frequencies: 2.4 GHz (for IEEE 802.11b/g) and 5 GHz (for IEEE 802.11a). For details, see "Antennas" on page 30.Status LEDs The status LEDs convey operational states for system power, and the LAN, Access, and Mesh interfaces. For details, see "Status LEDs" on page 29.802.11a RP-SMA Connector You can connect a detachable single-band antenna, such as the Pulse W1028 dipole antenna for the 5 GHz band, to  the male 802.11a RP-SMA (reverse polarity-subminiature version A) connector. Note that doing so disables the adjacent fixed antenna.PowerConnectorMounting Screw10/100 Mbps Power-over-Ethernet PortReset Button Console PortDevice Lock SlotFixed Dual-Band AntennasConnectors for Detachable Single-Band AntennasStatus LEDsRP-SMA Connector for 802.11a Radio AntennaRP-SMA Connector for 802.11b/g Radio Antenna
Deployment Guide 27 HIVEAP 20 PRODUCT OVERVIEWPower Connector The 48-volt DC power connector (0.38 amps) is one of two methods through which you can power the HiveAP 20. To connect it to a 100 – 240-volt AC power source, use the AC/DC power adaptor that is available as an extra option. Because the HiveAP does not have an on/off switch, connecting it to a power source automatically powers on the device.Mounting Screw To mount the HiveAP 20 on a surface, attach the mounting plate that ships with the product to the HiveAP by inserting the two pins on the underside of the chassis into slots in the plate and tightening the mounting screw. For details, see "Mounting the HiveAP 20" on page 31.10/100 Mbps PoE Port The 10/100-Mbps Ethernet port supports IEEE 802.3af PoE (Power over Ethernet) and receives RJ-45 connectors. The HiveAP can receive its power through an Ethernet connection to PSE (power sourcing equipment) that is 802.3af-compatible, such as one of the PoE injectors available as an optional accessory from Aerohive. (If you connect the HiveAP to a power source through the power connector and PoE port simultaneously, the device draws power through the power connector and automatically disables PoE.)The HiveAP can also connect to the wired network or to a wired device (such as a security camera) through this port. It is compatible with 10/100Base-T/TX and automatically negotiates half- and full-duplex connections with the connecting device. It is autosensing and adjusts to straight-through and cross-over Ethernet cables automatically. It also automatically adjusts for 802.3af Alternative A and B methods of PoE. For details, see "Ethernet and Console Ports" on page 28.Reset Button The reset button allows you to reboot the device or reset the HiveAP to its factory default settings. Insert a paper clip, or something similar, into the Reset pinhole and press the reset button. To reboot the device, hold the button down between 1 and 5 seconds. To return the configuration to the factory default settings, hold it down for at least 5 seconds. After releasing the button, the Power LED goes dark, and then glows steady amber while the firmware loads and the system performs a self-test. After the software finishes loading, the Power LED glows steady green.To disable the reset button from resetting the configuration, enter this command: no reset-button reset-config-enable Pressing the button between 1 and 5 seconds will still reboot the HiveAP, but pressing it for more than 5 seconds will not reset its configuration.Console Port A male DB-9 serial port to which you can make a console connection using an RS-232 (or "null modem") cable. The management station from which you make a serial connection to the HiveAP must have a VT100 emulation program, such as Tera Term Pro© (a free terminal emulator) or Hilgraeve Hyperterminal® (provided with Windows® operating systems). The following are the serial connection settings: bits per second: 9600, data bits: 8, parity: none, stop bits: 1, flow control: none.Device Lock Slot You can physically secure the HiveAP by attaching a lock and cable (such as a Kensington® notebook lock) to the device lock slot. After looping the cable around a secure object, insert the T-bar component of the lock into the slot on the HiveAP and turn the key to engage the lock mechanism.802.11b/g RP-SMA Connector You can connect a detachable single-band antenna, such as the Pulse W1038 dipole antenna for the 2.4 GHz band, to the male 802.11b/g RP-SMA connector. Note that doing so disables the adjacent fixed antenna.Component Description
Chapter 2 The HiveAP 20 ag Platform28 AerohiveEthernet and Console PortsThere are two ports on the HiveAP 20: a 10/100Base-T/TX Ethernet port and a male DB-9 console port. Both ports use standard pin assignments.The pin assignments in the PoE (Power over Ethernet) Ethernet port follow the TIA/EIA-568-B standard (see Figure 2). The PoE port accepts standard types of Ethernet cable—cat3, cat5, cat5e, or cat6—and can receive power over this cable from power sourcing equipment (PSE) that is 802.3af-compatible. Such equipment can be embedded in a switch or router, or it can come from purpose-built devices that inject power into the Ethernet line en route to the HiveAP. Because the PoE port has autosensing capabilities, the wiring termination in the Ethernet cable can be either straight-through or cross-over.Figure 2  PoE Wire Usage and Pin AssignmentsPin T568A Wire Color1 White/Green2 Green3 White/Orange4Blue5 White/Blue6 Orange7 White/Brown8Brown(View of the PoE port on the HiveAP)1 8Pin NumbersPin T568B Wire Color1 White/Orange2 Orange3 White/Green4Blue5 White/Blue6 Green7 White/Brown8BrownT568A-Terminated Ethernet Cable with an RJ-45 Connector802.3af Alternative A(Data and Power on the Same Wires)802.3af Alternative B(Data and Power on Separate Wires)Pin Data Signal MDI MDI-X MDI or MDI-X1 Transmit + DC+ DC– – – –2 Transmit - DC+ DC– – – –3 Receive + DC– DC+ – – –4 (unused) – – – – – – DC+5 (unused) – – – – – – DC+6 Receive - DC–  DC+ – – –7 (unused) – – – – – – DC–8 (unused) – – – – – – DC–MDI = Medium dependent interface for straight-through connectionsMDI-X = Medium dependent interface for cross-over (X) connectionsThe PoE port is auto-sensing and can automatically adjust to transmit and receive data over straight-through or cross-over Ethernet connections. Likewise, it can automatically adjust to 802.3af Alternative A and B power delivery methods. Furthermore, when the Alternative A method is used, the PoE port automatically allows for polarity reversals depending on its role as either MDI or MDI-X.T568B -terminated Ethernet Cable with an RJ-45 ConnectorT568A and T568B are two standard wiring termination schemes. Note that the only difference between them is that the white/green + solid green pair of wires and the white/orange + solid orange pair are reversed.For straight-through Ethernet cables—using either the T568A or T568B standard—the eight wires terminate at the same pins on each end.For cross-over Ethernet cables, the wires terminate at one end according to the T568A standard and at the other according to T568B.
Deployment Guide 29 HIVEAP 20 PRODUCT OVERVIEWThe pin assignments in the male DB-9 console port follow the EIA (Electronic Industries Alliance) RS-232 standard. To make a serial connection between your management system and the console port on the HiveAP, you can use a null modem serial cable, use another serial cable that complies with the RS-232 standard, or refer to the pin-to-signal mapping shown in Figure 3 to make your own serial cable. Connect one end of the cable to the console port on the HiveAP and the other end to the serial (or COM) port on your management system. The management system must have a VT100 terminal emulation program, such as Tera Term Pro© (a free terminal emulator) or Hilgraeve Hyperterminal® (provided with Windows® operating systems).Figure 3  Console Port Pin AssignmentsStatus LEDsThe four status LEDs on the top of the HiveAP 20 indicate various states of activity through their color (dark, green, amber) and illumination patterns (steady glow or blinking). The meanings of the various color + illumination patterns for each LED are explained below.Power•Dark: No power• Steady green: Powered on and the firmware is running normally• Steady amber: Firmware is booting up or is being updated• Blinking amber: Alarm indicating firmware failureLAN• Dark: Ethernet link is down or disabled• Steady green: Ethernet link is up but inactive• Blinking green: Ethernet link is up and activeAccess• Dark: Wireless link is disabled• Steady green: Wireless link is up but inactive• Blinking green: Wireless link is up and activeMesh• Dark: Wireless link is disabled• Steady green: Wireless link is up but inactive• Blinking green (fast): Wireless link is up and the HiveAP is searching for other hive members• Blinking green (slowly): Wireless link is up and active1 46 7 8 9Pin Signal Direction1 DCD (Data Carrier Detect) (unused)RXD (Received Data) InputTXD (Transmitted Data) Output4 DTR (Data Terminal Ready) (unused)Ground Ground6 DSR (Data Set Ready) (unused)7 RTS (Request to Send) (unused)8 CTS (Clear to Send) (unused)9 RI (Ring Indicator) (unused)Male DB-9 Console Port(View of the console port on the HiveAP) The above pin assignments show a DTE (data terminal equipment) configuration for a DB-9 connector complying with the RS-232 standard. Because this is a console port, only pins 2, 3, and 5 need be used.RS-232 Standard Pin Assignments
Chapter 2 The HiveAP 20 ag Platform30 AerohiveAntennasThe HiveAP 20 includes two fixed dual-band antennas with 3-dBi gains. These antennas are omnidirectional, providing fairly equal coverage in all directions in a toroidal (donut-shaped) pattern around each antenna. When the antennas are vertically positioned, coverage expands primarily on the horizontal plane, extending horizontally much more than vertically. See Figure 4, which shows the toroidal pattern emanating from a single vertically positioned antenna. To change coverage to be more vertical than horizontal, position the antennas horizontally. You can also resize the area of coverage by increasing or decreasing the signal strength. Figure 4  Omnidirectional Radiation PatternThe pair of fixed dual-band antennas operate concurrently in two different frequency ranges: 2.4 GHz (IEEE 802.11b/g) and 5 GHz (IEEE 802.11a). Using two different frequency ranges reduces the probability of interference that can occur when numerous channels operate within the same range. Conceptually, the relationship of antennas and radios is shown in Figure 5.Figure 5  Antennas and RadiosIf you connect an external antenna to an RP-SMA connector, you must enter the following command to move the appropriate interface from the adjacent fixed antenna to the external antenna:interface interface radio antenna externalNote: To show the shape of radiation more clearly, this illustration depicts the coverage provided by only one active antenna and is not drawn to scale.The omnidirectional antennas radiate equally in all directions, forming a toroidal pattern.HiveAPRadio 1RF 802.11b/g2.4 GHzRadio 2RF 802.11a5 GHzAntenna Switch 1 Antenna Switch 2RP-SMA Connectors802.11a/b/g Dual-Band Fixed Antenna802.11a/b/g Dual-Band Fixed AntennaCut-away view of the HiveAP to show the relationship of the antennas and the two internal radios.
Deployment Guide 31 MOUNTING THE HIVEAP 20The wifi0 interface links to radio 1 (frequency range = 2.4 GHz for IEEE 802.11b/g), and the wifi1 interface links to radio 2 (frequency range = 5 GHz for IEEE 802.11a). These interface-to-radio relationships are permanent. However, the interface-to-antenna relationships can be shifted. In other words, you can change which antenna—fixed or external—the wifi0 and wifi1 interfaces use. For example, to link the wifi0 interface to an external antenna connected to the 802.11b/g RP-SMA connector (for radio 1), enter the following command:interface wifi0 radio antenna external If you do not enter this command, the wifi0 interface and all its subinterfaces (wifi0.1, wifi0.2, wifi0.3 … wifi0.7) continue to use both fixed antennas.To unlink the wifi0 interface from the external antenna and return it to the fixed antennas, enter this command:interface wifi0 radio antenna internalMOUNTING THE HIVEAP 20Using the mounting plate and track clip, you can mount the HiveAP 20 to the tracks of a dropped ceiling grid. Using just the mounting plate, you can mount the HiveAP to any surface that can support its weight (1.5 lb., 0.68 kg).Ceiling MountTo mount the HiveAP 20 to a track in a dropped ceiling, you need the mounting plate, track clip, and two cross-head screws that ship with the track clip. You also need a cross-head screw driver and—most likely—a ladder.Attach the track clip to the mounting plate, and then attach the clip-plate combination to the HiveAP 20, as shown in Figure 6.Figure 6  Attaching the HiveAP 20 to the Mounting Plate and Track ClipNote: After entering the above command, the radio to which you attached the external antenna uses the external antenna and the fixed antenna on the opposite side of the HiveAP. Attaching an external antenna only disconnects the adjacent fixed antenna. Note the two antenna switches shown in Figure 5 on page 30.Align the two projecting posts on the underside of the track clip with holes in the mounting plate. Using the two cross-head screws that ship with the track clip, fasten the mounting plate to the track clip.Insert the pins on the underside of the HiveAP into the two slots in the mounting plate. Use the mounting screw to secure the HiveAP to the plate.1234
Chapter 2 The HiveAP 20 ag Platform32 AerohiveNudge the ceiling tiles slightly away from the track to clear some space. Then attach the track clip to the ceiling track as shown in Figure 7. When done, adjust the ceiling tiles back into their former position.Figure 7  Attaching the HiveAP to a Dropped Ceiling TrackSurface MountYou can use the mounting plate to attach the HiveAP 20 to any surface that supports its weight, and to which you can screw or nail the plate. First, mount the plate to the surface, and then attach the device to the plate, as shown in Figure 8.Figure 8  Mounting the HiveAP on a WallPress the track clip against the ceiling track so that the the track contacts the two pressure tabs and pushes them flush with the track clip.Rotate the HiveAP and the mounting accessories attached to it until the two clipping tabs grip the ceiling track.56(bird’s eye view with ceiling tiles removed for clarity)Use the mounting screw to secure the HiveAP 20 to the plate.Insert the pins on the underside of the HiveAP 20 into the two slots.With the two wings at the sides of the plate extending away from the surface, attach the mounting plate to a secure object such as a wall, ceiling, post, or beam.123Note: There are a variety of holes through which you can screw or nail the plate in place. Choose the two or three that best suit the object to which you are attaching it.
Deployment Guide 33 DEVICE, POWER, AND ENVIRONMENTAL SPECIFICATIONSDEVICE, POWER, AND ENVIRONMENTAL SPECIFICATIONSUnderstanding the range of specifications for the HiveAP 20 is necessary for optimal deployment and device operation. The following specifications describe the physical features and hardware components, the power adapter and PoE (Power over Ethernet) electrical requirements, and the temperature and humidity ranges in which the device can operate.Device Specifications• Chassis dimensions: 8 1/4" W x 1" H x 4 15/16" D (21 cm W x 2.5 cm H x 12.5 cm D)• Weight: 1.5 lb. (0.68 kg)• Antennas: Two fixed dual-band 802.11a/b/g antennas, and two RP-SMA connectors for detachable single-band 802.11a or 802.11b/g antennas• Serial port: DB-9 (bits per second: 9600, data bits: 8, parity: none, stop bits: 1, flow control: none)• Ethernet port: autosensing 10/100Base-T/TX Mbps, with IEEE 802.3af-compliant PoE (Power over Ethernet)Power Specifications• AC/DC power adapter:• Input:100 – 240 VAC• Output: 48V/0.38A• PoE nominal input voltages: 48 V, 0.35A• RJ-45 power input pins: Wires 4, 5, 7, 8 or 1, 2, 3, 6Environmental Specifications• Operating temperature: 32 to 122 degrees F (0 to 50 degrees C)• Storage temperature: -4 to 158 degrees F (-20 to 70 degrees C)• Relative Humidity: Maximum 95%
Chapter 2 The HiveAP 20 ag Platform34 Aerohive
Deployment Guide 35Chapter 3 The HiveAP 28 Outdoor PlatformThe Aerohive HiveAP 28 is a new generation wireless access point that is customized for outdoor use. It is mountable in any direction and on any hard surface, post, or wire strand. It can receive power either through an Ethernet cable or power cord.This guide combines product information, installation instructions, and configuration examples for both the HiveAP and HiveManager platforms. This chapter covers the following topics relating to the HiveAP 28:• "HiveAP 28 Product Overview" on page 36• "Ethernet Port" on page 37• "Power Connector" on page 38• "Antennas" on page 39• "Mounting the HiveAP 28 and Attaching Antennas" on page 40• "Pole Mount" on page 41• "Strand Mount" on page 42• "Surface Mount" on page 43• "Attaching Antennas" on page 44• "Device, Power, and Environmental Specifications" on page 46Note: Do not open the HiveAP 28 chassis. There are no serviceable parts inside.
Chapter 3 The HiveAP 28 Outdoor Platform36 AerohiveHIVEAP 28 PRODUCT OVERVIEWThe HiveAP 28 is a multi-channel wireless AP (access point) for outdoor use. It is compatible with IEEE 802.11b/g (2.4 GHz) and IEEE 802.11a (5 GHz) standards and supports a variety of Wi-Fi (wireless fidelity) security protocols, including WPA (Wi-Fi Protected Access) and WPA2.You can see the hardware components on the HiveAP 28 in Figure 1. Each component is described in Table 1.Figure 1  HiveAP 28 Hardware ComponentsTable 1  HiveAP 28 Component DescriptionsComponent DescriptionDetachable Single-Band Antennas The two pairs of detachable omnidirectional dipole antennas operate at two radio frequencies: one pair at 2.4 GHz (for IEEE 802.11b/g) and the other at 5 GHz (for IEEE 802.11a). For details, see "Antennas" on page 39.Type N Connectors (Female) Attach antennas to the HiveAP 28 through these connectors. For details, see "Attaching Antennas" on page 44.Waterproof Power Connector Using the power connector is one of two methods through which you can power the HiveAP 28. To connect it to a 100 – 240-volt AC power source, use the power cable that ships with the product as an extra option. Because the HiveAP does not have an on/off switch, connecting it to a power source automatically powers on the device. The power source must have a readily accessible service disconnect switch incorporated into the fixed wiring installation so that you have the ability to turn the power on and off. (The other method that the HiveAP can obtain power is through its PoE port.)5 GHz 2.4 GHz 5 GHz 2.4 GHzPowerConnector10/100 Mbps Power-over-Ethernet PortType N female connectors for detachable single-band antennas For the 802.11a Radio Antenna  For the 802.11b/g Radio Antenna  For the 802.11a Radio Antenna  For the 802.11b/g Radio AntennaFCC Compliance Label(Plus model, serial number, MAC address, and FCC ID number)802.11a Main Antenna (5 GHz) 802.11b/g Main Antenna (2.4 GHz)802.11b/g Auxiliary Antenna (2.4 GHz) 802.11a Auxiliary Antenna (5 GHz)
Deployment Guide 37 HIVEAP 28 PRODUCT OVERVIEWEthernet PortThe HiveAP 28 has a 10/100Base-T/TX PoE (Power over Ethernet) port. Its pin assignments follow the TIA/EIA-568-B standard (see Figure 2 on page 28). The PoE port accepts standard types of Ethernet cable—cat3, cat5, cat5e, or cat6—and can receive power over this cable from power sourcing equipment (PSE) that is 802.3af-compatible. Such equipment can be embedded in a switch or router, or it can come from purpose-built devices that inject power into the Ethernet line en route to the HiveAP. Because the PoE port has autosensing capabilities, the wiring termination in the Ethernet cable can be either straight-through or cross-over (MDI/MDI-X). For outdoor deployments use weatherproofed shielded twisted pair (STP) Ethernet cables.To ensure a waterproof seal for the Ethernet connection, use the RJ-45 connector assembly, which comes in three parts: a compression nut, end cap, and gasket.Figure 2  Connecting the Ethernet Cable1. Insert one end of the Ethernet cable through the waterproof RJ-45 connector assembly and plug the cable into the Ethernet port.2. Tighten the compression nut by twisting it clockwise into the Ethernet port housing on the chassis.3. Tighten the end cap by twisting it clockwise onto the compression nut and tighten until the rubber gasket emerges and wraps itself around the Ethernet cable.The Ethernet connection is now sealed and waterproof.10/100 Mbps PoE Port The 10/100-Mbps Ethernet port supports IEEE 802.3af PoE (Power over Ethernet) and receives RJ-45 connectors. The HiveAP can receive its power through an Ethernet connection to PSE (power sourcing equipment) that is 802.3af-compatible, such as one of the PoE injectors available as an optional accessory from Aerohive. (If you connect the HiveAP to a power source through the power connector and PoE port simultaneously, the device draws power through the power connector and automatically disables PoE.)The HiveAP 28 can also connect to the wired network or to a wired device (such as a security camera) through this port. It is compatible with 10/100Base-T/TX and automatically negotiates half- and full-duplex connections with the connecting device. It is autosensing and adjusts to straight-through and cross-over Ethernet cables automatically (MDI/MDI-X). It also automatically adjusts for 802.3af Alternative A and B methods of PoE. For details, see "Ethernet Port".Component Description2Compression NutEnd CapGasket (inside) Gasket (squeezed out)13Slide the Ethernet cable through the two halves of the waterproof RJ-45 connector assembly, screw the halves loosely together, and then plug the cable into the Ethernet port.Tighten the compression nut into the Ethernet port housing on the chassis.Tighten the end cap until the gasket is squeezed out the opening and forms a watertight seal around the cable.
Chapter 3 The HiveAP 28 Outdoor Platform38 Aerohive4. Connect the other end of the Ethernet cable to PSE (power sourcing equipment) such as a power injector if the HiveAP 28 receives power through PoE, or directly to a network device such as a switch if it receives power through a power cord.If the Ethernet cable connects the HiveAP to another device that is indoors, you must install appropriate lightning protection at the point before it enters the building. Failing to do so might cause damage to the equipment as well as serious injury or death.Power ConnectorThe HiveAP 28 can receive power through an Ethernet cable using PoE or through a power cord. Aerohive recommends using either PoE or wiring the power cord directly to a 100 – 240-volt AC power source. Only plug the power cord into an electric outlet when configuring the device before deployment or when testing it in the lab.To connect the power cord to the HiveAP 28:1. Align the slot in the power cord plug with the small tab at the top of the three-pin power connector, and slide the plug firmly over the pins until it is fully seated in the power connector.2. Slide the cover over the connector and tighten it by turning the cover clockwise.3. Install a lightning protector between the HiveAP 28 and its power source.4. When possible, run the cord through a conduit to protect it from the elements. Where the cord is exposed, allow enough slack in it to create a drip loop. Leaving some slack in the cord lets water run away from the connections at each end. Use only a weatherproof power cord, such as the cord that ships with the HiveAP 28.5. Strip the other end of the power cord and wire it directly to a power source, such as a junction box that has a service disconnect switch that you can use to turn the power on and off. Also, because the HiveAP 28 does not have short-circuit (over current) protection built into it, it relies on the protection provided by the power source to which you connect it. Ensure that the protective device, such as a circuit breaker, is not rated greater than 15A. Furthermore, if you need to install the HiveAP 28 in a wet or damp location, the AC branch circuit that is powering it must be provided with ground fault protection (GFCI), as required by Article 210 of the National Electrical Code (NEC).Note: To prevent damage to the HiveAP 28 or power injector when using PoE to provide power, connect the Ethernet cable from the power injector to the HiveAP 28, and connect the injector to a power jack before applying power.Note: When the HiveAP acts as a mesh point and does not use the Ethernet port, cover the Ethernet port with a connector cap to prevent water intrusion and possible safety hazards.Note: When the HiveAP receives power through PoE, cover the power connector with a connector cap to prevent water intrusion and possible safety hazards.Note: The HiveAP 28 must be grounded. Do not operate it unless there is a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.
Deployment Guide 39 HIVEAP 28 PRODUCT OVERVIEWAntennasThe HiveAP 28 includes two detachable single-band antennas with 8dBi gains (802.11b/g) and two detachable single-band antennas with 10dBi gains (802.11a). These antennas are omnidirectional, providing fairly equal coverage in all directions in a toroidal (donut-shaped) pattern around each antenna. When the antennas are vertically positioned, coverage expands primarily on the horizontal plane, extending horizontally much more than vertically. See Figure 3, which shows the toroidal pattern emanating from a single vertically positioned antenna. Note that when high gain antennas are added, the torus shape becomes somewhat elongated or compressed. If the HiveAP 28 is mounted higher than 20 feet the center of the torus curves inward so that the connection quality, directly underneath the center of the HiveAP 28, becomes compromised.To change coverage to be more vertical than horizontal, position the HiveAP so that the antennas are on a horizontal plane. You can also resize the area of coverage by increasing or decreasing the signal strength. Figure 3  Omnidirectional Radiation PatternThe pairs of antennas operate concurrently in two different frequency ranges: 2.4 GHz (IEEE 802.11b/g) and 5 GHz (IEEE 802.11a). Using two different frequency ranges reduces the probability of interference that can occur when numerous channels operate within the same range. Conceptually, the relationship of antennas and radios is shown in Figure 4. (For information about attaching the antennas to the HiveAP 28, see "Attaching Antennas" on page 44.)Figure 4  Antennas and RadiosNote: The HiveAP 20 uses the interface interface radio antenna external command to enable an external antenna attached to it. Entering this command on the HiveAP 28 disables the antenna on the opposite side of the device from the radio to which the interface is linked and results in a loss of diversity.Note: To show the shape of radiation more clearly, this illustration depicts the coverage provided by only one active antenna and is not drawn to scale.The omnidirectional antennas radiate equally in all directions, forming a toroidal pattern.HiveAPThe two 802.11b/g antennas link internally to Radio 1 and broadcast in the 2.4 GHz frequency range.802.11a Main Antenna 802.11b/g Main Antenna802.11b/g Auxiliary Antenna 802.11a Auxiliary AntennaThe two 802.11a antennas link internally to Radio 2 and broadcast in the 5 GHz frequency range.Radio 1RF 802.11b/g2.4 GHzRadio 2RF 802.11a5 GHz
Chapter 3 The HiveAP 28 Outdoor Platform40 AerohiveMOUNTING THE HIVEAP 28 AND ATTACHING ANTENNASUsing the mounting accessories (available separately) you can mount the HiveAP in various locations:• "Pole Mount" on page 41 – Mount the HiveAP 28 on a pole such as a street light.• "Strand Mount" on page 42 – Suspend the HiveAP 28 from a cable or phone line.• "Surface Mount" on page 43 – Mount the HiveAP 28 on a flat surface such as a wall or beam.You can mount the HiveAP 28 in any of these locations as long as the object to which you mount it and the attaching screws can support its weight (9 lbs., 4.08 kg).After mounting the HiveAP 28, attach the antennas as explained in "Attaching Antennas" on page 44.Before you mount the HiveAP 28 and attach antennas, read the following warnings and cautions:• To install the HiveAP 28, you must be a qualified installation professional, licensed or certified in accordance with local regulations.• Use lightning arrestors and ground both the HiveAP 28 and any separately mounted antennas.• Do not connect or disconnect antennas or cables from the HiveAP 28 during periods of lightning activity.• If you need to place the HiveAP 28 in an explosive environment, such as in an oil refinery, mine, or any place where there is flammable gas, it must first be encased in an ATEX enclosure.• To comply with RF (radio frequency) exposure limits, do not place antennas within 6.56 feet (2 meters) of people.• Do not locate antennas near overhead power lines or other electric light or power circuits, or where they can come into contact with such circuits. When installing antennas, take extreme care not to come into contact with these circuits, which might cause serious injury or death. For proper installation and grounding of the antenna, refer to national and local electrical codes: NFPA (National Fire Protection Association) 70, National Electrical Code Article 810 (U.S.); Canadian Electrical Code, Part I, CSA 22.1 and Section 54 (Canada); and if local or national electrical codes are not available, refer to IEC (International Electrotechnical Commission) 364, Part 1 through 7 (other countries).• To prevent damage, avoid over-tightening the connectors, nuts, and screws used to mount the HiveAP 28 and antennas.
Deployment Guide 41 MOUNTING THE HIVEAP 28 AND ATTACHING ANTENNASPole MountTo mount the HiveAP 28 to a pole with a 1.5-inch diameter, you need two sets of the L-shaped brackets, two 2" U-bolts, saddle clamps, and the nuts, bolts, and washers shown in Figure 5. You also need a wrench to tighten the nuts and bolts securely.Figure 5  Attaching the HiveAP 28 to a Pole1. Align two of the holes in the shorter end of the bracket with two of the holes in the HiveAP, insert the two bolts through the washers and bracket, and screw them into the holes in the HiveAP 28 chassis, using a wrench to tighten the bolts so that the bracket is securely attached.2. Holding a saddle clamp against the inside of the long end of one of the L-shaped brackets, slip a U-bolt around the pole and thread it through the two holes in the saddle clamp and L-shaped bracket.3. Thread a split washer and 5/16-18 nut to each end of the U-bolt, and tighten them with a wrench to secure the U-bolt firmly to the pole.Note: Repeat this step to attach the other bracket to the HiveAP. However, this time, place the long end of the bracket in the opposite direction of the first one for better stability. For example, if you attached the first bracket with its long end positioned toward the outside edge of the device, install this second bracket with the long end of the bracket toward the middle.Note: One of the holes in the bracket is arc-shaped so that you can adjust the angle of the mounted device if necessary.Note: Repeat steps 2 and 3 to attach the other U-bolt and saddle clamp to the remaining L-shaped bracket and secure the HiveAP 28 to the pole.5 GHz 2.4 GHzSaddle ClampVertical Pole (1.5” diameter) 2” U-BoltSplit Washers5/16-18 NutsL-Shaped Bracket1/4-20 BoltsandSplit WashersBird’s-Eye ViewSide view of the HiveAP 28 mounted to a street lightNote: For clarity, only one post mounting set is shown in the illustration. You also need to use a second set to finish mounting the HiveAP on a pole.Use the 1/4-20 bolts and split washers to attach the shorter end of the L-shaped bracket to holes in the underside of the HiveAP 28.Slip the U-bolt around the pole and thread its ends through the saddle clamp and L-shaped bracket.Thread the split washers and 5/16-18 nuts over the ends of the U-bolt and tighten until the bracket assembly and device are secured to the pole. 123
Chapter 3 The HiveAP 28 Outdoor Platform42 AerohiveStrand MountThe HiveAP 28 outdoor platform can also be mounted on a cable or strand of wire as shown in Figure 6. When mounted on a wire strand, use 90-degree N type adapters (not included) to orient the antennas vertically. If you do not use the adapters and orient the antennas horizontally, the area covered will be far less. Figure 6  Clamping the HiveAP 28 to a Wire StrandTo mount the HiveAP 28 on a wire or strand, you need a wrench and two 1/4-20 bolts, split washers, strand clamps, and 90-degree type N adapters. In the following instructions, you use only the 2.4 GHz antennas.1. Position the HiveAP 28 so that its long side (with three holes at each end) is underneath a cable or wire strand running lengthwise along the upper side of the chassis (for the proper orientation, see the inset in Figure 6).2. Place the strand clamp over the wire and use the 1/4-20 bolt and split washer to secure the strand between the clamp and chassis.3. Attach the 90-degree type N adapters to the two 2.4 GHz antenna connectors and then attach the antennas to the adapters so that the antennas face downward. For details, see "Attaching Antennas" on page 44.Note: Repeat the preceding steps to fasten the other end of the HiveAP 28 to the cable or wire strand.5 GHz 2.4 GHzStrand ClampSplit WasherStrand1/4-20 BoltEnd ViewSide ViewSide view of the HiveAP 28 mounted on a cable strand90-Degree Type N Adapter90-Degree Type N Adapter2.4 GHz AntennasNote: For clarity, only one bolt, washer, and strand clamp are shown in the illustration on the left. You also need to use a second set of these items to finish clamping the HiveAP to a wire strand.Position the HiveAP 28 so that its long side is directly beneath a cable or wire strand.Place the strand clamps over the wire, and bolt the clamps tightly to the chassis around the strand.12Attach 90-degree type N adapters to the 2.4 GHz antenna connectors so that the adapters face downward, and then attach the antennas to the adapters3
Deployment Guide 43 MOUNTING THE HIVEAP 28 AND ATTACHING ANTENNASSurface MountYou can use the mounting plate to attach the HiveAP 28 to any surface that supports its weight (9 lbs., 4.08 kg), and to which you can screw or nail the plate. First, mount the plate to the HiveAP 28, and then attach the plate to the surface, as shown in Figure 7. Note that the screw heads that you attach to the wall or surface must be small enough for the keyholes on the mounting plate to slip over them.Figure 7  Mounting the HiveAP 28 on a WallTo mount the HiveAP 28 to a surface like a wall, you need two mounting plates, four 1/4-20 x 1/2" flat head screws, four screws (no bigger than 5/16"), and a screw driver: 1. Align the ridged edge of one of the mounting plates with two of the holes located on the underside of the HiveAP 28, and use two 1/4-20 x 1/2" flat head screws to secure the plate against the HiveAP 28. Then attach the other mounting plate to the HiveAP 28 in the same way.2. Attach four 5/16" screws to a wall or beam. They must be 8 1/8" (206 mm) apart vertically and 7 7/8" (200 mm) apart horizontally to accommodate the keyholes on the mounting plates.3. Guide the keyholes over the screws fastened to the wall and push downward after the screw heads have cleared the keyholes.Note: Because the metal in a wall can degrade the radio signal pattern, Aerohive recommends using sector antennas instead of omnidirectional antennas when mounting the device on a wall.5 GHz 2.4 GHz7 7/8”200 mmTop of Wall5 GHz 2.4 GHzMounting Plate1/4-20 x 1/2” Flat Head ScrewsBird’s-Eye ViewSide view of the HiveAP 28 mounted on an exterior wallGuide the screws fastened to the wall through the keyholes in the mounting plates.Attach four screws to a secure object such as a wall or beam. Space them 8 1/8" (206 mm) apart vertically and 7 7/8" (200 mm) apart horizontally.With the ridged edge of the holes on the mounting plates facing the HiveAP 28, use 1/4-20 x 1/2 inch screws to secure the two mounting plates to its underside.1 2 3Note: For clarity, only one mounting plate is shown in the illustration. You also need a second plate with another set of screws.
Chapter 3 The HiveAP 28 Outdoor Platform44 AerohiveAttaching AntennasYou can connect the antennas directly to the HiveAP 28 or mount them separately. Although connecting the antennas directly to the device typically provides better performance, in some cases the location of the HiveAP might not be a good location for the antennas; for example, if the HiveAP 28 is mounted on a reinforced concrete wall that interferes with radio coverage. In such cases, mounting the antennas separately in a more open location can improve coverage; however, bear in mind that cables introduce loss into the overall signal strength and that the longer the cable connecting the antennas to the HiveAP 28, the greater the loss will be.Connecting Antennas Directly to the HiveAP 28The two 2.4 GHz and two 5 GHz antennas that ship with the HiveAP 28 have male Type N connectors that you can connect directly to the female Type N antenna connectors on the HiveAP 28. You can also use self-amalgamating PTFE (polytetrafluoroethylene) tape, which is available separately from Aerohive, to create a waterproof seal at the points of attachment.To attach the antennas: 1. Remove the antenna connector covers from the HiveAP 28 (leave the covers on any connectors that you do not plan to use), and make sure that the surface of the connectors on the HiveAP 28 and the connectors on the antennas are clean.2. If you are using PTFE tape, wrap the tape around the threads on the HiveAP 28 antenna connectors as follows:2.1. Starting at one end of the threads on one of the connectors, stretch the tape and wrap it in half-lap layers until you cover the threads completely.2.2. Wrap the tape in the opposite direction to bring it back onto itself for one full wrap.2.3. Place one thumb on the tape at the point of termination and stretch the tape until it breaks.2.4. Repeat the preceding steps to cover all the connectors to which you will attach antennas.3. Connect the 2.4 GHz antennas to the 2.4 GHz antenna connectors. (To tighten an antenna, turn the antenna base cap—the textured metal band that encloses the connector—clockwise over the tape-covered threads of the HiveAP antenna connector.)Their connections are now sealed and waterproof.4. Repeat the preceding steps to connect the 5 GHz antennas.Mounting Antennas SeparatelyIn addition to connecting antennas directly to the HiveAP 28, you can also mount them separately and run a cable between the antennas and the device. Use either male-to-female cables with Type N connectors or use male-to-male or female-to-female cables with cable gender changers. (The antennas have male Type N connectors and the HiveAP 28 has female Type N connectors.)Note: Cover any unused antenna connectors with a connector cap to prevent water intrusion and possible safety hazards.Note: Using cables to mount antennas separately causes some signal loss and using a cable gender changer can cause even more. The amount of loss varies from product to product, so refer to the documentation accompanying the cables and gender changer you use for information. To minimize loss, Aerohive recommends using LMR400 cables and using the shortest cables possible.
Deployment Guide 45 MOUNTING THE HIVEAP 28 AND ATTACHING ANTENNASYou can mount antennas at the top of a pole as shown in Figure 8 and Figure 9, or to a flat surface. If you must mount the antenna lower on a pole, the pole must be nonmetallic—such as one made from a hard plastic like PVC (polyvinyl chloride)—so that it does not distort the signal. Aerohive recommends that antennas be installed away from power lines and obstructions that can interfere with radio coverage.For each antenna that you mount, you need an attachment clamp, a 1 3/8" bolt and nut, a V-bolt, two washers and two nuts, a hose clamp, and two wrenches.Figure 8  Securing an Antenna to an Attachment Clamp1. Insert the 1 3/8" bolt through the attachment clamp and screw a nut loosely onto its end.2. Place the antenna base cap inside the attachment clamp.3. Using a pair of wrenches, tighten the nut to the bolt until the clamp grips the base cap firmly.Figure 9  Mounting an Antenna to a Pole4. To mount the antenna on a nonmetallic pole, place the attachment clamp against the pole, thread the V-bolt through the holes on the attachment, the washers, and nuts, and use the wrenches to tighten the nuts to the bolt. (Optional) For added stability, fasten the top of the antenna to the pole with the hose clamp.To mount the antenna directly to a flat surface, run bolts or screws (not included) through the two holes in the attachment clamp, and fasten them firmly to the surface.Attachment ClampBase CapAntenna1 3/8” Bolt NutUse one wrench to hold the nut in place and the other to tighten the bolt.Insert the antenna into the clamp until it grips the base cap.Insert the bolt through the attachment clamp and hold it in place with the nut. Do not tighten it yet.1 2 3Nonmetallic Pole(2” diameter) AntennaHose ClampBird’s-Eye ViewV-BoltSide ViewNutsWashersAttachment ClampWith the attachment clamp against one side of the pole, insert the V-bolt through the two holes in the clamp from the other side. Then thread washers and nuts over the two ends of the bolt and tighten them in place with a wrench.4Note: Aerohive recommends attaching the antenna near the top of the pole. If you need to improve the stability of the mounted antenna, fasten it to the pole with a hose clamp (included) as shown on the far right. or
Chapter 3 The HiveAP 28 Outdoor Platform46 Aerohive5. Make sure that all the antenna and cable connectors are clean. If you are using PTFE tape, wrap the tape around the threads on the HiveAP 28 antenna connectors as explained in "Connecting Antennas Directly to the HiveAP 28" on page 44.6. Assuming that you are using male-to-female cables, connect the female Type N connector on the cables to the male connectors on the antennas.7. Connect the male Type N connectors on the cables to the female antenna connectors on the HiveAP 28.DEVICE, POWER, AND ENVIRONMENTAL SPECIFICATIONSUnderstanding the range of specifications for the HiveAP is necessary for optimal deployment and device operation. The following specifications describe the physical features and hardware components, the power adapter and PoE (Power over Ethernet) electrical requirements, and the temperature and humidity ranges in which the device can operate.Device Specifications• Chassis dimensions: 13 13/16" W x 4 3/8" H x 8 3/8" D (35 cm W x 11 cm H x 21 cm D)• Weight: (9 lbs., 4.08 kg)• Antennas: Two detachable single-band 8dBi 802.11b/g antennas and two detachable single-band 10dBi 802.11a antennas• Maximum Transmission Power: 20 dBm• Ethernet port: autosensing 10/100Base-T/TX Mbps, with IEEE 802.3af-compliant PoE (Power over Ethernet)Power Specifications• AC/DC power adapter:• Input:100 – 240 VAC• Output: 17 watts• PoE nominal input voltages: 48 V, 0.35A• RJ-45 power input pins: Wires 4, 5, 7, 8 or 1, 2, 3, 6•RF power output:Environmental Specifications• Operating temperature: -40 to 140 degrees F (-40 to 60 degrees C)• Storage temperature: -40 to 194 degrees F (-40 to 90 degrees C)• Relative Humidity: Maximum 100%Note: Radio coverage might be limited if the surface acts as an obstruction.802.11b RF (8-dBi Omnidirectional Antenna, Model S2406BFNM)Frequency 2412 MHz 2437 MHz 2462 MHzPeak Power Output (dBm) 14.20 14.00 14.20802.11g RF (8-dBi Omnidirectional Antenna, Model S2406BFNM)Frequency 2412 MHz 2437 MHz 2462 MHzPeak Power Output (dBm) 16.20 16.80 15.00802.11a RF (10-dBi Omnidirectional Antenna, Model S4908WBF)Frequency 5745 MHz 5785 MHz 5825 MHzPeak Power Output (dBm) 17.80 17.40 17.60
Deployment Guide 47Chapter 4 The HiveAP 340 PlatformThe Aerohive HiveAP 340 is a high-performance and highly reliable 802.11n wireless access point. The HiveAP 340 provides dual concurrent 802.11b/g/n and 802.11a/n radios for 3x3 MIMO (Multiple In, Multiple Out) and dual 10/100/1000 Ethernet ports for link aggregation or link redundancy. Its power management system uses a concept called smart PoE (Power over Ethernet) to adjust its power consumption automatically in response the available power in different environments. Smart PoE supports the IEEE 802.3af standard and the 802.3at pre-standard.This chapter covers the following topics relating to the HiveAP 340:• "HiveAP 340 Product Overview" on page 48• "Ethernet and Console Ports" on page 50• "Status LEDs" on page 54• "Antennas" on page 54• "Mounting the HiveAP 340" on page 58• "Ceiling Mount" on page 58• "Surface Mount" on page 60• "Device, Power, and Environmental Specifications" on page 61
Chapter 4 The HiveAP 340 Platform48 AerohiveHIVEAP 340 PRODUCT OVERVIEWThe HiveAP 340 is a multi-channel wireless access point. It is compatible with IEEE 802.11b/g/n (2.4 GHz) and IEEE 802.11a/n (5 GHz) standards and supports a variety of Wi-Fi (wireless fidelity) security protocols, including WPA (Wi-Fi Protected Access) and WPA2.You can see the hardware components on the HiveAP in Figure 1. Each component is described in Table 1.Figure 1  HiveAP 340 Hardware ComponentsTable 1  HiveAP 340 Component DescriptionsComponent DescriptionStatus LEDs The status LEDs convey operational states for system power, firmware, Ethernet interfaces, and radios. For details, see "Status LEDs" on page 54.Device Lock Slot You can physically secure the HiveAP by attaching a lock and cable (such as a Kensington® notebook lock) to the device lock slot or by using the lock adapter that is included in the mounting kit and a padlock. For more information, see "Locking the HiveAP 340" on page 59.802.11a/b/g/n RP-SMA Connectors You can connect up to six detachable single-band antennas to the male 802.11a/b/g/n RP-SMA (reverse polarity-subminiature version A) connectors. Connect the longer antennas, which support 2.4 GHz frequencies (for IEEE 802.11b/g/n), to the connectors on the side panel with the Ethernet ports. Connect the shorter antennas, which support 5 GHz frequencies (for IEEE 802.11a/n), to the connectors on the side panel with the device lock slot. For details, see "Antennas" on page 54.2.4 GHz (A) 2.4 GHz (B) 2.4 GHz (C)ETH0 ETH1 48V DC(.625A)CONSOLE RESET5 GHz (A)5 GHz (B)5 GHz (C)PowerConnector10/100 /1000 Mbps PoE Ports Reset ButtonConsole PortDevice Lock SlotStatus LEDs802.11b/g/n RP-SMA Connectors for Detachable Single-Band Antennas802.11a/n RP-SMA Connectors for Detachable Single-Band Antennas
Deployment Guide 49 HIVEAP 340 PRODUCT OVERVIEW10/100/1000 Mbps PoE Ports The two 10/100/1000-Mbps Ethernet ports—ETH0 and ETH1—support IEEE 802.3af and 802.3at PoE (Power over Ethernet) and receive RJ-45 connectors. The HiveAP can receive power through one or both Ethernet connections from PSE (power sourcing equipment) that is compatible with the 802.3af standard and the forthcoming 802.at standard, such as one of the PoE injectors available as an optional accessory from Aerohive. (If you connect the HiveAP to a power source through the power connector and PoE ports simultaneously, the device draws power through the power connector and automatically disables PoE.)You can configure ETH0 and ETH1 as two individual Ethernet interfaces, combine them into an aggregate interface to increase throughput, or combine them into a redundant interface to increase reliability. You can connect the HiveAP 340 to a wired network or to a wired device (such as a security camera) through these ports using bridging. They are compatible with 10/100/1000Base-T/TX and automatically negotiate half- and full-duplex connections with the connecting device. They are autosensing and adjust to straight-through and cross-over Ethernet cables automatically. For details, see "Ethernet and Console Ports" on page 50.Power Connector The 48-volt DC power connector (0.625 amps) is one of two methods through which you can power the HiveAP 340. To connect it to a 100 – 240-volt AC power source, use the AC/DC power adaptor that is available as an extra option. Because the HiveAP does not have an on/off switch, connecting it to a power source automatically powers on the device.Console Port You can access the CLI by making a serial connection to the RJ-45 console port. The management station from which you make a serial connection to the HiveAP must have a VT100 emulation program, such as Tera Term Pro© (a free terminal emulator) or Hilgraeve Hyperterminal® (provided with Windows® operating systems). The following are the serial connection settings: bits per second: 9600, data bits: 8, parity: none, stop bits: 1, flow control: none. For details, see "Ethernet and Console Ports" on page 50.Reset Button The reset button allows you to reboot the device or reset the HiveAP to its factory default settings. Insert a paper clip, or something similar, into the Reset pinhole and press the reset button. To reboot the device, hold the button down between 1 and 5 seconds. To return the configuration to the factory default settings, hold it down for at least 5 seconds. After releasing the button, the Power LED goes dark as the system reboots. Then it pulses green while the firmware loads and the system performs a self-test. After the software finishes loading, the Power LED glows steady green.To disable the reset button from resetting the configuration, enter this command: no reset-button reset-config-enable Pressing the button between 1 and 5 seconds will still reboot the HiveAP, but pressing it for more than 5 seconds will not reset its configuration.Note: The rear surface of the HiveAP 340 is used for heat dissipation to reduce the internal temperature. Consequently, it can become hot, so use caution when handling it.Component Description
Chapter 4 The HiveAP 340 Platform50 AerohiveEthernet and Console PortsThere are three ports on the HiveAP 340: two RJ-45 10/100/1000Base-T/TX Ethernet ports and an RJ-45 console port.The pin assignments in the PoE (Power over Ethernet) Ethernet ports follow the TIA/EIA-568-B standard (see Figure 2). The ports accept standard types of Ethernet cable—cat3, cat5, cat5e, or cat6—and can receive power over this cable from power sourcing equipment (PSE) that is 802.3af-compatible. If you use cat5, cat5e, or cat6 cables, the HiveAP 340 can also support 802.3at-compliant PSE. Such equipment can be embedded in a switch or router, or it can come from purpose-built devices that inject power into the Ethernet line en route to the HiveAP. Because the PoE ports have autosensing capabilities, the wiring termination in the Ethernet cable can be either straight-through or cross-over.Figure 2  PoE Wire Usage and Pin AssignmentsETH0Pin T568A Wire Color1 White/Green2 Green3 White/Orange4Blue5 White/Blue6 Orange7 White/Brown8Brown(View of the ETH0 PoE Port on the HiveAP 340)8 1Pin NumbersPin T568B Wire Color1 White/Orange2 Orange3 White/Green4Blue5 White/Blue6 Green7 White/Brown8BrownT568A-Terminated Ethernet Cable with an RJ-45 Connector802.3af Alternative A(Data and Power on the Same Wires)802.3af Alternative B(Data and Power on Separate Wires)802.3at Wiring OptionsPin Data Signal MDI MDI-X MDI or MDI-X 1 2 3 41 Transmit + DC+ DC– – – – DC1+ DC1– DC1+ DC1–2 Transmit - DC+ DC– – – – DC1+ DC1– DC1+ DC1–3 Receive + DC– DC+ – – – DC1– DC1+ DC1– DC1+4 (unused) – – – – – – DC+ DC2+ DC2+ DC2– DC2–5 (unused) – – – – – – DC+ DC2+ DC2+ DC2– DC2–6 Receive - DC–  DC+ – – – DC1– DC1+ DC1– DC1+7 (unused) – – – – – – DC– DC2– DC2– DC2+ DC2+8 (unused) – – – – – – DC– DC2– DC2– DC2+ DC2+MDI = Medium dependent interface for straight-through connectionsMDI-X = Medium dependent interface for cross-over (X) connectionsThe PoE ports are auto-sensing and can automatically adjust to transmit and receive data over straight-through or cross-over Etherneconnections. L kewise, they can automatically adjust to 802.3af Alternative A and B power delivery methods. Furthermore, when the Alternative A method is used, the ports automatically allow for polarity reversals depending on their role as either MDI or MDI-X. In 802.3at, the 1/2 and 3/6 wire pairs connect to DC source 1 and 4/5 and 7/8 pairs to DC source 2 in PSE. Although the exact polarity depends on the PSE design, the HiveAP 340 Ethernet ports can support all possible options.T568B -terminated Ethernet Cable with an RJ-45 ConnectorT568A and T568B are two standard wiring termination schemes. Note that the only difference between them is that the white/green + solid green pair of wires and the white/orange + solid orange pair are reversed.For straight-through Ethernet cables—using either the T568A or T568B standard—the eight wires terminate at the same pins on each end.For cross-over Ethernet cables, the wires terminate at one end according to the T568A standard and at the other according to T568B.
Deployment Guide 51 HIVEAP 340 PRODUCT OVERVIEWSmart PoEThe HiveAP 340 applies the Aerohive concept of smart PoE to adjust power consumption as necessitated by varying levels of available power. No adjustments are needed when the power level is 17.5 W (watts) or higher. If the available power drops to a range between 16 and 17.5 W, the HiveAP disables the ETH1 interface. If the level drops to the 14.4 – 16 W range, it then switches from 3x3 MIMO (Multiple In, Multiple Out) to 2x3 (see "MIMO" on page 55). In rare cases when the power drops between 12 and 14.4 W and further power conservation is necessary, the HiveAP reduces the speed on ETH0 from 10/100/1000 Mbps to 10/100 Mbps. Finally, in the event that there is a problem with the PoE switch or Ethernet cable and the power falls between 0 and 12 W, the HiveAP disables its wireless interfaces and returns its ETH0 and ETH1 interfaces to 10/100/1000 Mbps speeds. Through the application of smart PoE, the HiveAP 340 can make power usage adjustments so that it can continue functioning even when the available power level drops.Aggregate and Redundant InterfacesBy default ETH0 and ETH1 act as two individual Ethernet interfaces. When both interfaces are connected to the network and are in backhaul mode, the HiveAP transmits broadcast traffic only through ETH0. The HiveAP transmits broadcast traffic through ETH1 only when ETH0 does not have network connectivity. When both Ethernet interfaces are connected to the network and are in access mode, then the HiveAP transmits broadcast traffic through all the access interfaces: ETH0, ETH1, and all wireless subinterfaces in access mode.In addition to using ETH0 and ETH1 as individual interfaces, you can combine them into an aggregate interface (agg0) to increase throughput, or combine them into a redundant interface (red0) to increase reliability. The logical red0 and agg0 interfaces support all the settings that you can configure for Ethernet interfaces except those pertaining to physical link characteristics such as link speed. See the sections below for configuration information.Aggregate InterfaceYou can increase throughput onto the wired network by combining ETH0 and ETH1 into a single logically aggregated interface called "agg0". The aggregate interface effectively doubles the bandwidth that each physical interface has when used individually. In this configuration, both Ethernet ports actively forward traffic, the HiveAP applying an internal scheduling mechanism based on the source MAC address of each packet to send traffic through the aggregate member interfaces. To configure an aggregate interface, enter the following commands:interface eth0 bind agg0interface eth1 bind agg0In addition to configuring the HiveAP, you must also configure the connecting switch to support EtherChannel. For example, the following commands bind two physical Ethernet ports—0/1 and 0/2—to the logical interface port-channel group 1 on a Cisco Catalyst 2900 switch running Cisco IOS 12.2:Switch#conf tSwitch(config)#interface port-channel 1Switch(config-if)#switchport mode accessSwitch(config-if)#spanning-tree portfastSwitch(config-if)#exitSwitch(config)#interface fastEthernet 0/1Switch(config-if)#switchport mode accessSwitch(config-if)#channel-group 1 mode onSwitch(config-if)#spanning-tree portfastSwitch(config-if)#exit
Chapter 4 The HiveAP 340 Platform52 AerohiveSwitch(config)#int fastEthernet 0/2Switch(config-if)#switchport mode accessSwitch(config-if)#channel-group 1 mode onSwitch(config-if)#spanning-tree portfastSwitch(config-if)#exitSwitch(config)#exitSwitch#wr memFinally, you must cable the Cisco switch and the HiveAP together: Cisco 0/1 to HiveAP eth0, and Cisco 0/2 to HiveAP eth1.Redundant InterfaceIf a single Ethernet link provides sufficient bandwidth and speed, such as a 1000 Mbps link, but you want to ensure link redundancy, you can connect the two Ethernet ports to the same switch—or to two different switches—and configure them to act as a redundant interface called "red0". In this mode, only one Ethernet interface is actively forwarding traffic at any one time. If eth0 is active and eth1 is passive and eth0 loses its connection, the HiveAP switches over to eth1. To configure a redundant interface, enter the following commands:interface eth0 bind red0 primaryinterface eth1 bind red0The interface that you specify as primary is the one that the HiveAP uses when both interfaces have network connectivity. Because the HiveAP uses eth0 as the primary interface by default, it is unnecessary to specify "primary" in the first command above. However, it is included to make the role of eth0 as the primary interface obvious. Interface Selection for the Default RouteIn cases where there are multiple active interfaces in backhaul mode, the HiveAP uses the following logic to choose which interface to use in its default route: • If there is an Ethernet interface and a wireless interface in backhaul mode, the HiveAP uses the Ethernet interface in its default route.• If there are multiple Ethernet interfaces in backhaul mode, the HiveAP chooses which one to use in its default route in the following order:• It uses red0 or agg0 if one of them has at least one member interface bound to it and its link state is UP.• It uses ETH0 if neither red0 nor agg0 has any member interfaces and the link state for ETH0 is UP.• It uses ETH1 if neither red0 nor agg0 has any member interfaces, the link state for ETH0 is DOWN, and the link state for ETH1 is UP.Note: No extra configuration is necessary on the connecting switch or switches to support a redundant interface.
Deployment Guide 53 HIVEAP 340 PRODUCT OVERVIEWConsole PortThe pin-to-signal mapping in the RJ-45 console port is shown shown in Figure 3.Figure 3  Console Port Pin AssignmentsTo make a serial connection between your management system and the HiveAP, you can use the console cable that is available as an extra option. Insert the RJ-45 connector into the HiveAP 340 console port, and attach the DB-9 connector to the serial (or COM) port on your management system. The management system must have a VT100 terminal emulation program, such as Tera Term Pro© (a free terminal emulator) or Hilgraeve Hyperterminal® (provided with Windows® operating systems). If you want to make your own serial cable and adapter, refer to Figure 3.Figure 4  Wiring Details for Making a Serial Cable with an RJ-45-to-Female DB-9 AdapterCONSOLEPin Signal Direction1 RTS (Request to Send) Output, unused2 DTR (Data Terminal Ready) Output, unusedTXD (Transmitted Data) OutputGround GroundGround GroundRXD (Received Data) Input7 DSR (Data Set Ready) Input, unused8 CTS (Clear to Send) Input, unusedRJ-45 Console Port(View of the console port on the HiveAP) Because this is a console port, only pins 3, 4, 5, and 6 are currently in use.Console Port Pin Assignments17 28Rollover Cable with RJ-45 ConnectorsRJ-45-to-Female DB-9 AdapterConsole PortCOM Port (on Back Panel)CONSOLEManagement SystemHiveAP 340Console Port (HiveAP 340) RJ-45-to-RJ-45 Rollover Cable RJ-45-to-Female DB-9 Adapter Management SystemSignal RJ-45 Pin RJ-45 Pin RJ-45 Pin DB-9 Pin SignalRTS (Request to Send) 1 8 1 8 CTS (unused)DTR (Data Terminal Ready) 2 7 2 6 DSR (unused)TXD (Transmitted Data) 3 6 3 2 RXDGround 4 5 4 5 GroundGround 5 4 5 5 GroundRXD (Received Data) 6 3 6 3 TXDDSR (Data Set Ready) 7 2 7 4 DTR (unused)CTS (Clear to Send) 8 1 8 7 RTS (unused)- - - - 9 RI (Ring Indicator, unused)
Chapter 4 The HiveAP 340 Platform54 AerohiveStatus LEDsThe five status LEDs on the top of the HiveAP 340 indicate various states of activity through their color (dark, green, amber, and red) and illumination patterns (steady glow or pulsing). The meanings of the various color + illumination patterns for each LED are explained below.Power•Dark: No power• Steady green: Powered on and the firmware is running normally• Pulsing green: Firmware is booting up• Steady amber: Firmware is being updated• Pulsing amber: Alarm indicating a firmware issue has occurred• Steady red: Alarm indicating a hardware issue has occurredETH0 and ETH1• Dark: Ethernet link is down or disabled• Steady green: 1000 Mbps Ethernet link is up but inactive• Pulsing green: 1000 Mbps Ethernet link is up and active• Steady amber: 10/100 Mbps Ethernet link is up but inactive• Pulsing amber: 10/100 Mbps Ethernet link is up and activeWIFI0 and WIFI1• Dark: Wireless interface is disabled• Steady green: Wireless interface is in access mode but inactive• Pulsing green: Wireless interface is in access mode and active• Steady amber: Wireless interface is in backhaul mode but inactive• Pulsing amber: Wireless interface is in backhaul mode and is connected with other hive members• Alternating green and amber: Wireless interface is in backhaul mode and is searching for other hive membersAntennasThe HiveAP 340 can accept up to six detachable dipole antennas. The three shorter antennas are designed for the 5 GHz band and have a 2-dBi gain. The three longer antennas are designed for the 2.4 GHz band and have a 4.9-dBi gain. These antennas are omnidirectional, providing fairly equal coverage in all directions in a toroidal (donut-shaped) pattern around each antenna (see Figure 4 on page 30). For greater coverage on a horizontal plane, it is best to orient the antennas vertically. So that you can easily do that whether the HiveAP chassis is mounted horizontally or vertically, the antennas hinge and swivel (see Figure 5 on page 55.)Although hive members automatically adjust their signal strength according to their environments, you can resize the area of coverage by increasing or decreasing the signal strength manually by entering the interface { wifi0 | wifi1 } radio power <number> command, where <number> can be from 1 to 20 and represents a value in dBm.
Deployment Guide 55 HIVEAP 340 PRODUCT OVERVIEWFigure 5  HiveAP 340 AntennasMIMOMIMO (Multiple In, Multiple Out) is a major WLAN advancement introduced in the IEEE 802.11n standard in which multiple RF links are formed on the same channel between the transmitter and receiver simultaneously. To accomplish this, the transmitter separates a single data stream into multiple spatial streams, one for each RF chain (an antenna + various digital signal processing modules linked to the antenna). The transmit antennas at the end of each RF chain then transmit their spatial streams. The recipient’s receive antennas obtain streams from all the transmit antennas. In fact, due to multipath, they receive multiple streams from each transmit antenna. The receive antennas pass the spatial streams to the digital signal processors in their RF chains, which take the best data from all the spatial streams and reassemble them into a single data stream once again (see Figure 6).Figure 6  2x2 MIMO (2 Transmit Antennas x 2 Receive Antennas)5 GHz Antenna for IEEE 802.11a/nLength when fully extended: 5 15/16” (15 cm)2.4 GHz Antenna for IEEE 802.11b/g/nLength when fully extended: 7 7/8” (20 cm)The base of the antennas hinge up to 90 degrees so that you can orient the antennas independently of the orientation of the HiveAP chassis. The antennas also rotate in a full circle.When mounting the HiveAP 340 on a ceiling, orient its antennas downward.When mounting the HiveAP on a wall or post, fully extend its antennas upward and downward.When mounting the HiveAP above a ceiling or on a horizontal beam, orient its antennas upward.Generally, orient the antennas vertically for improved radio coverage, as shown here:Transmit AntennasDigital Signal ProcessorsRF Chains RF Signals  (Multipath)Receive Antennas Digital Signal ProcessorsRF Chains802.11n wireless client with two antennas HiveAP 340 using two antennasObjectData Reassembled Data
Chapter 4 The HiveAP 340 Platform56 AerohiveIn previous 802.11 standards, access points and clients each employed a single set of components, or RF chain, for transmitting or receiving. Although two antennas are often used for diversity, only the one with the best signal-to-noise ratio is used at any given moment, and that antenna makes use of the single RF chain while the other antenna remains inactive. A significant improvement that MIMO introduces is to permit each antenna to have its own RF chain and for all antennas to function simultaneously. For the HiveAP 340, you can connect up to three antennas per radio and configure the radio to use two or three transmit chains and two or three receive chains.1 Using two or three transmit and receive chains simultaneously increases the amount of data that can flow across the WLAN and accelerates the processing of that data at each end of the wireless link.Another major aspect of MIMO is how it turns multipath signals from a curse to a boon. As a radio signal moves through space, some objects reflect it, others interfere with it, and still others absorb it. The receiver can end up receiving multiple copies of the original signal, all kind of muddled together. However, the digital signal processors in the multiple receive chains are able to combine their processing efforts to sort through all the received data and reconstruct the original message. Furthermore, because the transmitter makes use of multiple RF chains, there is an even richer supply of signals for the receive chains to use in their processing. To set the transmit and receive RF chains for a radio profile, enter the following commands:radio profile <name> transmit-chain { 2 | 3 }radio profile <name> receive-chain { 2 | 3 }There are two sets of antennas—three antennas per set—that operate concurrently in two different frequency ranges: 2.4 GHz (IEEE 802.11b/g/n) and 5 GHz (IEEE 802.11a/n). Using two different frequency ranges reduces the probability of interference that can occur when numerous channels operate within the same range. Conceptually, the relationship of antennas and radios is shown in Figure 7.Figure 7  Antennas and RadiosThe wifi0 interface links to radio 1 (frequency range = 2.4 GHz for IEEE 802.11b/g), and the wifi1 interface links to radio 2 (frequency range = 5 GHz for IEEE 802.11a). These interface-to-radio relationships are permanent.When deciding how many antennas to use, consider the types of wireless clients—802.11n only, 802.11g/n, 802.11b/g/n, or 802.11a/n—the area needing coverage, and the RF environment.1. The convention for presenting the configuration of transmitting and receiving MIMO RF chains is TxR. For example, a HiveAP 340 radio functioning in access mode might be configured to use two RF chains for transmitting and three for receiving. In that case, its configuration can be presented as "2x3". In general, the number of receive antennas is equal to or greater than the number of transmit antennas.PWRETH1ETH0WIFI1WIFI0Radio 1RF 802.11b/g/n2.4 GHzRadio 2RF 802.11a/n5 GHz2.4 GHz (A)2.4 GHz (B)2.4 GHz (C)5 GHz (A)5 GHz (B)5 GHz (C)RP-SMA ConnectorsRP-SMA ConnectorsCut-away view of the HiveAP 340 to show the relationship of the antennas and the two internal radios
Deployment Guide 57 HIVEAP 340 PRODUCT OVERVIEWUsing MIMO with Legacy ClientsIn addition to supporting up to 300-Mbps throughput per radio for 802.11n clients, MIMO (Multiple In, Multiple Out) can improve the reliability and speed of legacy 802.11a/b/g client traffic. When an 802.11a/b/g access point does not receive acknowledgement that a frame it sent was received, it resends that frame, possibly at a somewhat lower transmission rate. If the access point must continue resending frames, it will continue lowering its transmission rate. As a result, clients that could get 54-Mbps throughput in an interference-free environment might have to drop to 48- or 36-Mbps speeds due to multipath interface. However, because MIMO technology makes better use of multipath, an access point using MIMO can continue transmitting at 54 Mbps, or at least at a better rate than it would in a pure 802.11a/b/g environment, thus improving the reliability and speed of 802.11a/b/g client traffic.Although 802.11a/b/g client traffic can benefit somewhat from an 802.11n access point using MIMO, supporting such legacy clients along with 802.11n clients can have a negative impact on 802.11n client traffic. Legacy clients take longer to send the same amount of data as 802.11n clients. Consequently, legacy clients consume more airtime than 802.11n clients do, causing greater congestion in the WLAN and reducing 802.11n performance. By default, the HiveAP 340 supports 802.11a/b/g clients. You can restrict access only to clients using the IEEE 802.11n standard. By only allowing traffic from clients using 802.11n, you can increase the overall bandwidth capacity of the access point so that there will not be an impact on 802.11n clients during times of network congestion. To do that, enter the following command:radio profile <string> 11n-clients-onlyYou can also deny access just to clients using the IEEE 802.11b standard, which has the slowest data rates of the three legacy standards, while continuing to support 802.11a and 802.11g clients. To do that, enter the following command:no radio profile <string> allow-11b-clientsBy blocking access to 802.11b clients, their slower data rates cannot clog the WLAN when the amount of wireless traffic increases.
Chapter 4 The HiveAP 340 Platform58 AerohiveMOUNTING THE HIVEAP 340Using the mounting plate and track clips, you can mount the HiveAP 340 to the tracks of a dropped ceiling grid. Using just the mounting plate, you can mount the HiveAP to any surface that can support its weight (3.3 lb., 1.5 kg).Ceiling MountTo mount the HiveAP 340 to a track in a dropped ceiling, you need the mounting plate, two track clips, and two Keps nuts, all of which ship as an option with the HiveAP 340. You also need a drill and—most likely—a ladder.Nudge the ceiling tiles slightly away from the track to clear some space. Attach the track clips to the ceiling track, and then fasten the mounting plate to the clips, as shown in Figure 8. When you have the mounting plate in the correct location, cut or drill a hole in the ceiling through which you can then pass the Ethernet and power cables.Figure 8  Attaching the Track Clips and Mounting Plate to the Ceiling TrackAttach the HiveAP 340 to the mounting plate and connect the cables, as shown in Figure 9 on page 59.Note: You can tie the cables to the tie points (small arched strips) on the mounting plate to prevent them from being pulled out of their connections accidentally.Mounting Plate12Press the track clips against the ceiling track and swivel them until they snap into place, gripping the edges of the track.If necessary, slide one or both of the clips along the track to position them at the proper distance (2 1/4” or 7 cm) to fit through the holes in the mounting plate.Insert the mounting track over the screws attached to the track clips, and use the Keps nuts to fasten the plate firmly to the screws on the clips.Use a wrench to tighten the nuts firmly to the bolts and secure the plate to the track.3Through the oblong opening in the plate, drill a hole in the ceiling tile (not shown). Then pass one or both Ethernet cables through the hole, and if you plan to supply power from an AC power source rather than through PoE, pass the power cable through as well.Drill a hole in the ceiling tile and feed cables through here.Ceiling TrackTrack Clip(worms’s eye view with ceiling tiles removed for clarity)2 1/4 “ (7 cm)
Deployment Guide 59 MOUNTING THE HIVEAP 340Figure 9  Attaching the HiveAP 340 to the Mounting Plate and Connecting CablesWhen done, adjust the ceiling tiles back into their former position.Locking the HiveAP 340To lock the HiveAP 340 to the mounting plate, use either a Kensington lock or the lock adapter that is included with the mounting kit and a small padlock (not included).To use a Kensington lock, loop the cable attached to the lock around a secure object, insert the T-bar component of the lock into the device lock slot on the HiveAP, and then turn the key to engage the lock mechanism.To use the lock adapter :1. Insert the T-shaped extension on the adapter into the device lock slot, and rotate it clockwise so that the curved section extends through the slot in the mounting plate (see Figure 10).Figure 10 Locking the HiveAP 340 to the Mounting Plate2. Link a padlock through the opening in the adapter and engage the lock to secure the HiveAP 340 to the mounting plate. The opening is 1/8" (0.3 cm) in diameter at its narrowest.With the HiveAP 340 upside down, align its port side with the bottom end of the plate.Push the HiveAP 340 upward, inserting the four tabs on the plate into the four slots on the HiveAP 340.Slide the HiveAP 340 toward the bottom end of the plate, locking the tabs inside the slots.Attach the antennas and connect the cables to complete the installation.4675Tab inside slot.Tab  locked in place.Mounting PlateHiveAP 340 (shown as transparent for clairty)TabSlot(side view)Mounting PlateHiveAP 340CeilingCables pass through the hole in the mounting plate and ceiling5 GHz (A)5 GHz (B)5 GHz (C)Rotate the lock adapter clockwise.Insert a lock through the opening.HiveAP 340Mounting Plate
Chapter 4 The HiveAP 340 Platform60 AerohiveSurface MountYou can use the mounting plate to attach the HiveAP 340 to any surface that supports its weight, and to which you can screw or nail the plate. First, mount the plate to the surface. Then, through one of the two large openings in the plate, make a hole in the wall so that you can pass the cables through to the HiveAP.Finally, attach the device to the plate, and connect the cables, as shown in Figure 11.Figure 11 Mounting the HiveAP on a WallNote: You can tie the cables to the tie points on the mounting plate to prevent them from being pulled out of their connections accidentally.Mounting PlateHiveAP 340WallInsert the tabs on the mounting plate into the slots on the underside of the HiveAP 340. Then push the HiveAP 340 downward to lock it in place.With the two wings at the sides of the plate extending away from the surface, attach the mounting plate to a secure object such as a wall, ceiling, post, or beam.13Note: There are a variety of holes through which you can screw or nail the plate in place. Choose the two or three that best suit the object to which you are attaching it.HiveAP 3402Cut or drill a hole through one of the openings in the mounting plate to pass the cables through to the HiveAP 340.Connect the cables to the HiveAP 340.Depending on the deployment, you might connect one or two Ethernet cables and a power cable.4(side view)
Deployment Guide 61 DEVICE, POWER, AND ENVIRONMENTAL SPECIFICATIONSDEVICE, POWER, AND ENVIRONMENTAL SPECIFICATIONSUnderstanding the range of specifications for the HiveAP 340 is necessary for optimal deployment and device operation. The following specifications describe the physical features and hardware components, the power adapter and PoE (Power over Ethernet) electrical requirements, and the temperature and humidity ranges in which the device can operate.Device Specifications• Chassis dimensions: 8 1/2" W x 1 1/4" H x 8" D (21.5 cm W x 3.2 cm H x 20.3 cm D)• Weight: 3 lb. (1.36 kg)• Antennas: Three omnidirectional 802.11b/g/n antennas, and three omnidirectional 802.11a/n antennas• Serial port: RJ-45 (bits per second: 9600, data bits: 8, parity: none, stop bits: 1, flow control: none)• Ethernet ports: autosensing 10/100/1000 Base-T/TX Mbps; both ports are compliant with the IEEE 802.3af standard and the forthcoming 802.at standard for PoE (Power over Ethernet)Power Specifications• AC/DC power adapter:• Input:100 – 240 VAC• Output: 48V/0.38A• PoE nominal input voltages: • 802.3af: 48 V/0.35A• Pre-802.3at: 48 V/0.625A • RJ-45 power input pins: Wires 4, 5, 7, 8 or 1, 2, 3, 6Environmental Specifications• Operating temperature: -4 to 131 degrees F (-20 to 55 degrees C)• Storage temperature: -40 to 176 degrees F (-40 to 80 degrees C)• Relative Humidity: Maximum 95%
Chapter 4 The HiveAP 340 Platform62 Aerohive
Deployment Guide 63Chapter 5 The HiveAP 320 PlatformThe Aerohive HiveAP 320 is a high-performance and highly reliable 802.11n wireless access point. The HiveAP 320 provides dual concurrent 802.11b/g/n and 802.11a/n radios for 3x3 MIMO (Multiple In, Multiple Out) and dual 10/100/1000 Ethernet ports for link aggregation or link redundancy. Its power management system uses a concept called smart PoE (Power over Ethernet) to adjust its power consumption automatically in response the available power in different environments. Smart PoE supports the IEEE 802.3af standard and the 802.3at pre-standard.This chapter covers the following topics relating to the HiveAP 320:• "HiveAP 320 Product Overview" on page 64• "Ethernet and Console Ports" on page 66• "Status LEDs" on page 66• "Antennas" on page 67• "Mounting the HiveAP 320" on page 68• "Ceiling Mount" on page 68• "Surface Mount" on page 70• "Device, Power, and Environmental Specifications" on page 71Note: The HiveAP 320 supports all same 802.11n features as the HiveAP 340. Of particular interest is its support of MIMO (Multiple Input, Multiple Output). For more information, see "MIMO" on page 55 and "Using MIMO with Legacy Clients" on page 57.
Chapter 5 The HiveAP 320 Platform64 AerohiveHIVEAP 320 PRODUCT OVERVIEWThe HiveAP 320 is a multi-channel wireless access point. It is compatible with IEEE 802.11b/g/n (2.4 GHz) and IEEE 802.11a/n (5 GHz) standards and supports a variety of Wi-Fi (wireless fidelity) security protocols, including WPA (Wi-Fi Protected Access) and WPA2.You can see the hardware components on the HiveAP in Figure 1. Each component is described in Table 1.Figure 1  HiveAP 320 Hardware ComponentsTable 1  HiveAP 320 Component DescriptionsComponent DescriptionStatus LEDs The status LEDs convey operational states for system power, firmware, Ethernet interfaces, and radios. For details, see "Status LEDs" on page 66.ETH0 10/100/1000 Mbps PoE Portand ETH1 10/100/1000 Mbps Port The two 10/100/1000-Mbps Ethernet ports—ETH0 and ETH1—receive RJ-45 connectors. The HiveAP can receive power through an Ethernet connection to the ETH0 port from PSE (power sourcing equipment) that is compatible with the 802.3af standard and the forthcoming 802.at standard. Aerohive provides suitable PoE injectors as an optional accessory. (If you connect the HiveAP to a power source through the power connector and the ETH0 PoE port simultaneously, the device draws power through the power connector and automatically disables PoE.)ETH0 ETH1 48VDC CONSOLEStatus LEDsPOWERWLAN0WLAN1ETH0ETH1Device Lock Slot Reset ButtonMounting Plate
Deployment Guide 65 HIVEAP 320 PRODUCT OVERVIEWYou can configure ETH0 and ETH1 as two individual Ethernet interfaces, combine them into an aggregate interface to increase throughput, or combine them into a redundant interface to increase reliability. You can connect the HiveAP 320 to a wired network or to a wired device (such as a security camera) through these ports using bridging. They are compatible with 10/100/1000Base-T/TX and automatically negotiate half- and full-duplex connections with the connecting device. They are autosensing and adjust to straight-through and cross-over Ethernet cables automatically. For details, see "Ethernet and Console Ports" on page 66.48VDCPower Connector The 48-volt DC power connector (0.625 amps) is one of two methods through which you can power the HiveAP 320. To connect it to a 100 – 240-volt AC power source, use the AC/DC power adaptor that is available as an extra option. Because the HiveAP does not have an on/off switch, connecting it to a power source automatically powers on the device.Console Port You can access the CLI by making a serial connection to the RJ-45 console port. The management station from which you make a serial connection to the HiveAP must have a VT100 emulation program, such as Tera Term Pro© (a free terminal emulator) or Hilgraeve Hyperterminal® (provided with Windows® operating systems). The following are the serial connection settings: bits per second: 9600, data bits: 8, parity: none, stop bits: 1, flow control: none. For details, see "Ethernet and Console Ports" on page 66.Device Lock Slot You can physically secure the HiveAP by attaching it to a mounting plate that is clipped to a ceiling track and then using a screw with a unique head design to fasten the HiveAP to the mounting plate through the device lock slot. The screw and special screw driver that fits the slot on the screw head are included in the mounting kit. For more information, see "Locking the HiveAP 320" on page 69.Reset Button The reset button allows you to reboot the device or reset the HiveAP to its factory default settings. Insert a paper clip, or something similar, into the Reset pinhole and press the reset button. To reboot the device, hold the button down between 1 and 5 seconds. To return the configuration to the factory default settings, hold it down for at least 5 seconds. After releasing the button, the Power LED goes dark as the system reboots. Then it pulses green while the firmware loads and the system performs a self-test. After the software finishes loading, the Power LED glows steady green.To disable the reset button from resetting the configuration, enter this command: no reset-button reset-config-enable Pressing the button between 1 and 5 seconds will still reboot the HiveAP, but pressing it for more than 5 seconds will not reset its configuration.Note: The rear surface of the HiveAP 320 is used for heat dissipation to reduce the internal temperature. Consequently, it can become hot, so use caution when handling it.Component Description
Chapter 5 The HiveAP 320 Platform66 AerohiveEthernet and Console PortsThere are three ports on the HiveAP 320: two RJ-45 10/100/1000Base-T/TX Ethernet ports and an RJ-45 console port.The pin assignments in the PoE (Power over Ethernet) Ethernet ports follow the TIA/EIA-568-B standard (see Figure 2 on page 50). The ports accept standard types of Ethernet cable—cat3, cat5, cat5e, or cat6. The ETH0 port can receive power over the Ethernet cable from power sourcing equipment (PSE) that is 802.3af-compatible. If you use cat5, cat5e, or cat6 cables, the ETH0 port can also support 802.3at-compliant PSE. Such equipment can be embedded in a switch or router, or it can come from purpose-built devices that inject power into the Ethernet line en route to the HiveAP. Because the PoE ports have autosensing capabilities, the wiring termination in the Ethernet cable can be either straight-through or cross-over.The HiveAP 320 supports the following features on its Ethernet ports:• The HiveAP 320 supports smart PoE on its ETH0 port to adapt its power consumption to changes in the amount of power available to it over Ethernet from PSE (power sourcing equipment). For more information, see "Smart PoE" on page 51.• The two Ethernet interfaces can be configured as aggregate interfaces for increased throughput and redundant interfaces for increased reliability. For more information, see "Aggregate and Redundant Interfaces" on page 51.Through the RJ-45 console port, you can make a serial connection between your management system and the HiveAP. The pin-to-signal mapping of the RJ-45 console port is the same as that for the HiveAP 340, which is shown shown in Figure 3 on page 53. Similarly, cabling and connection details for the HiveAP 320 are same as those for the HiveAP 340 (see Figure 4 on page 53).Status LEDsThe five status LEDs on the top of the HiveAP 320 indicate various states of activity through their color (dark, green, amber, and red) and illumination patterns (steady glow or pulsing). The meanings of the various color + illumination patterns for each LED are explained below.Power•Dark: No power• Steady green: Powered on and the firmware is running normally• Pulsing green: Firmware is booting up• Steady amber: Firmware is being updated• Pulsing amber: Alarm indicating a firmware issue has occurred• Steady red: Alarm indicating a hardware issue has occurredETH0 and ETH1• Dark: Ethernet link is down or disabled• Steady green: 1000 Mbps Ethernet link is up but inactive• Pulsing green: 1000 Mbps Ethernet link is up and active• Steady amber: 10/100 Mbps Ethernet link is up but inactive• Pulsing amber: 10/100 Mbps Ethernet link is up and activeWIFI0 and WIFI1• Dark: Wireless interface is disabled• Steady green: Wireless interface is in access mode but inactive• Pulsing green: Wireless interface is in access mode and active• Steady amber: Wireless interface is in backhaul mode but inactive• Pulsing amber: Wireless interface is in backhaul mode and is connected with other hive members• Alternating green and amber: Wireless interface is in backhaul mode and is searching for other hive members
Deployment Guide 67 HIVEAP 320 PRODUCT OVERVIEWAntennasThe HiveAP 320 has six internal single-band antennas. Three of the antennas operate in the 2.4-GHz band (IEEE 802.11b/g/n) and have a 2-dBi gain. The other three antennas operate in the 5-GHz band (IEEE 802.11a/n) and have a 3-dBi gain. All antennas are omnidirectional, providing fairly equal coverage in all directions in a toroidal (donut-shaped) pattern around each antenna (see Figure 4 on page 30).The three three 2.4-GHz antennas link to radio 1, and the three 5-GHz antennas link to radio 2. Conceptually, the relationship of antennas and radios is shown in Figure 2.Figure 2  Antennas and RadiosThe wifi0 interface links to radio 1 (frequency range = 2.4 GHz for IEEE 802.11b/g), and the wifi1 interface links to radio 2 (frequency range = 5 GHz for IEEE 802.11a). These interface-to-radio relationships are permanent.Although hive members automatically adjust their signal strength according to their environments, you can resize the area of coverage by increasing or decreasing the signal strength manually by entering the interface { wifi0 | wifi1 } radio power <number> command, where <number> can be from 1 to 20 and represents a value in dBm.Radio 1RF 802.11b/g/n2.4 GHzRadio 2RF 802.11a/n5 GHz2.4 GHzAntennas 5 GHzAntennasRRF 8o 111b/g/n5 GH.4 GHzCut-away view of the HiveAP 320 to show the relationship of the antennas and the two internal radios
Chapter 5 The HiveAP 320 Platform68 AerohiveMOUNTING THE HIVEAP 320Using the mounting plate and track clips, you can mount the HiveAP 320 to the tracks of a dropped ceiling grid. Using just the mounting plate, you can mount the HiveAP to any surface that can support its weight (2 lb., 0.68 kg).Ceiling MountTo mount the HiveAP 320 to a track in a dropped ceiling, you need the mounting plate, two track clips, and two Keps nuts. all of which ship as an option with the HiveAP 320. You also need a drill and—most likely—a ladder.Nudge the ceiling tiles slightly away from the track to clear some space. Fasten the track clips to the mounting plate, and then attach them to the ceiling track, as shown in Figure 3.Figure 3  Attaching the Track Clips and Mounting Plate to the Ceiling TrackWhen you have the mounting plate in the correct location, cut or drill a hole in the ceiling through which you can then pass the Ethernet and power cables. Pass the cables through the hole and attach them to the HiveAP 320, leaving some slack so that you can easily maneuver the HiveAP into place, attaching it to the mounting plate as shown in Figure 4 on page 69.Note: In addition to these methods, you can also mount the HiveAP 320 on a table using the set of four rubber feet that ship with the product. Simply peel the rubber feet off the adhesive sheet and press them against the underside of the HiveAP in its four corners.Note: For clarity, the power and Ethernet cables are not shown in the illustrations.Ceiling TrackTrack ClipsMounting Plate31Press the clips against the ceiling track and swivel them until they snap into place, gripping the edges of the track.If necessary, slide the clips and mounting plate along the track until they are in the spot you want.Insert the screws through the mounting plate and thread them into the track clips, fastening the clips firmly to the plate.2Adjust the track clips so that their tabs can pass on either side of a ceiling track.
Deployment Guide 69 MOUNTING THE HIVEAP 320Figure 4  Attaching the HiveAP 320 to the Mounting PlateWhen done, adjust the ceiling tiles back into their former position.Locking the HiveAP 320To lock the HiveAP 320 to the mounting plate, use the security screw and bit that are included with the mounting kit. You will also need a screw driver or an electric drill that will accept the bit.1. Insert the security screw through the hole in the HiveAP 320 and begin to thread it into the hole in the mounting plate (see Figure 5).Figure 5  Locking the HiveAP 320 to the Mounting Plate2. With the security screw bit in a screw driver or electric drill, tighten the screw into place, securing the HiveAP to the mounting plate.Push HiveAPWith the HiveAP 320 upside down, align the round tab and security screw hole extnesion on the mounting plate with the keyhole opening and security screw cavity on the HiveAP 320, and press the HiveAP upward.45Pushing from the LED end of the HiveAP, slide it toward the bottom end of the plate until the two rippled tabs on the mounting plate snap over the nubs on the undersdie of the HiveAP.Security ScrewHiveAP 320Mounting PlateCeiling Track Note: The ceiling tiles are removed for clarity.
Chapter 5 The HiveAP 320 Platform70 AerohiveSurface MountYou can use the mounting plate to attach the HiveAP 320 to any surface that supports its weight, and to which you can screw or nail the plate. First, mount the plate to the surface. Then, through the large opening in the lower part of the plate, make a hole in the wall so that you can pass the cables through to the HiveAP.Finally, attach the device to the plate, and connect the cables, as shown in Figure 6.Figure 6  Mounting the HiveAP 320 on a WallNote: You can use the locking screw to secure the HiveAP 320 to the mounting plate. For information, see "Locking the HiveAP 320" on page 69.Insert the tabs on the mounting plate into the slots on the underside of the HiveAP 320. Then push the HiveAP 320 downward to lock it in place.Orient the mounting plate as shown and attach it to a secure object such as a wall, ceiling, post, or beam.13Note: There are a variety of holes through which you can screw or nail the plate in place. Choose the two or three that best suit the object to which you are attaching it.HiveAP 3202Cut or drill a hole through the large space near the bottom of the mounting plate to pass the cables through to the HiveAP 320.Connect the cables to the HiveAP 320.Depending on the deployment, you might connect one or two Ethernet cables and a power cable.4(side view) wallMounting Plate
Deployment Guide 71 DEVICE, POWER, AND ENVIRONMENTAL SPECIFICATIONSDEVICE, POWER, AND ENVIRONMENTAL SPECIFICATIONSUnderstanding the range of specifications for the HiveAP 320 is necessary for optimal deployment and device operation. The following specifications describe the physical features and hardware components, the power adapter and PoE (Power over Ethernet) electrical requirements, and the temperature and humidity ranges in which the device can operate.Device Specifications• Chassis dimensions: 7 7/8" W x 1 1/2" H x 7 7/8" D (20 cm W x 3.8 cm H x 20 cm D)• Weight: 2 lb. (0.68 kg)• Antennas: Three omnidirectional 802.11b/g/n antennas, and three omnidirectional 802.11a/n antennas• Serial port: RJ-45 (bits per second: 9600, data bits: 8, parity: none, stop bits: 1, flow control: none)• Ethernet ports: two autosensing 10/100/1000 Base-T/TX Mbps ports; the ETH0 port is compliant with the IEEE 802.3af standard and the forthcoming 802.at standard for PoE (Power over Ethernet)Power Specifications• AC/DC power adapter:• Input:100 – 240 VAC• Output: 48V/0.38A• PoE nominal input voltages: • 802.3af: 48 V/0.35A• Pre-802.3at: 48 V/0.625A • RJ-45 power input pins: Wires 4, 5, 7, 8 or 1, 2, 3, 6Environmental Specifications• Operating temperature: 32 to 104 degrees F (0 to 40 degrees C)• Storage temperature: -4 to 158 degrees F (-20 to 70 degrees C)• Relative Humidity: Maximum 95%
Chapter 5 The HiveAP 320 Platform72 Aerohive
Deployment Guide 153Chapter 10 HiveOSYou can deploy a single HiveAP and it will provide wireless access as an autonomous AP (access point). However, if you deploy two or more HiveAPs in a hive, you can provide superior wireless access with many benefits. A hive is a set of HiveAPs that exchange information with each other to form a collaborative whole (see Figure 1). Through coordinated actions based on shared information, hive members can provide the following services that autonomous APs cannot:• Consistent QoS (quality of service) policy enforcement across all hive members• Coordinated and predictive wireless access control that provides fast roaming to clients moving from one hive member to another• Best-path routing for optimized data forwarding• Automatic radio frequency and power selectionFigure 1  HiveAPs in a HiveHive MembersWired or Wireless Hive Communications (Backhaul)Wireless Network Access ConnectionsWired Ethernet Network ConnectionsNot shown: Switches for wired backhaul connections and the portal link to the wired network.Wireless Clients Wireless ClientsWireless ClientsHive
Chapter 10 HiveOS154 AerohiveCOMMON DEFAULT SETTINGS AND COMMANDSMany major components of HiveOS are automated and typically require no further configuration. For example, radio power and frequency selection occurs automatically, as does route learning. Also, after defining a hive and its security protocol suite, all HiveAPs belonging to that hive automatically initiate and maintain communications with each other.Additionally, there are many default settings that simplify the setup of a HiveAP because these are the typical settings for many of the most common deployments. The following are some important default settings and the commands necessary to change them if you need to do so:Default Settings Commandsmgt0 interface DHCP client = enabled To disable the DHCP client:no interface mgt0 dhcp clientTo set an IP address:interface mgt0 ip ip_addr netmaskVLAN ID = 1 To set a different VLAN ID:interface mgt0 vlan numberwifi0 and wifi1 interfaces wifi0 mode = accesswifi1 mode = backhaul To change the mode of the wifi0 or wifi1 interface:interface { wifi0 | wifi1 } mode { access | backhaul }wifi0 radio profile = radio_g0wifi1 radio profile = radio_a0 To change the radio profile of the wifi0 or wifi1 interface to a different, previously defined profile:interface { wifi0 | wifi1 } radio profile stringantenna = internal To have the wifi0 interface use an external antenna:interface { wifi0 | wifi1 } radio antenna externalchannel = automatic selection To set a specific radio channel:interface { wifi0 | wifi1 } radio channel numberpower = automatic selection To set a specific transmission power level (in dBms):interface { wifi0 | wifi1 } radio power numberDefault QoS policy def-user-qos policy: user profile rate = 54,000 Kbpsuser profile weight = 10user rate limit = 54,000 Kbpsmode = weighted round robin for Aerohive classes 0 - 5; strict forwarding for classes 6 - 7classes 0 - 4 rate limit = 54,000 Kbpsclass 5 rate limit = 10,000 Kbpsclasses 6 - 7 rate limit = 512 KbpsTo change the default QoS policy:qos policy def-user-qos qos ah_class {strict rate_limit 0 | wrr rate_limit weight }qos policy def-user-policy user-profile rate_limit weightqos policy def-user-policy user rate_limitUser profile default-profile:group ID = 0policy name = def-user-qosVLAN ID = 1You cannot change the group ID or QoS policy name for the default user profile. To change its VLAN ID:user-profile default-profile vlan-id number
Deployment Guide 155 CONFIGURATION OVERVIEWCONFIGURATION OVERVIEWThe amount of configuration depends on the complexity of your deployment. As you can see in "Deployment Examples (CLI)" on page 161, you can enter a minimum of three commands to deploy a single HiveAP, and just a few more to deploy a hive.However, for cases when you need to fine tune access control for more complex environments, HiveOS offers a rich set of CLI commands. The configuration of HiveAPs falls into two main areas: "Device-Level Configurations" and "Policy-Level Configurations" on page 156. Consider your deployment plans and then refer to the following sections for guidance on the commands you need to configure them.Device-Level ConfigurationsDevice-level configurations refer to the management of a HiveAP and its connectivity to wireless clients, the wired network, and other hive members. The following list contains some key areas of device-level configurations and relevant commands.• Management• Administrators, admin authentication method, login parameters, and admin privileges admin { auth | manager-ip | min-password-length | read-only | read-write | root-admin } …• Logging settingslog { buffered | console | debug | facility | flash | server | trap } …• Connectivity settings•Interfacesinterface { eth0 | wifi0 | wifi1 } …• Layer 2 and layer 3 forwarding routesroute mac_addr …ip route { default | host | net } ip_addr …• VLAN assignmentsFor users:user-profile string qos-policy string vlan-id number attribute numberFor hive communications:hive string native-vlan numberFor the mgt0 interface:interface mgt0 vlan number• Radio settingsradio profile string …Note: To find all commands using a particular character or string of characters, you can do a search using the following command: show cmds | { include | exclude } string
Chapter 10 HiveOS156 AerohivePolicy-Level ConfigurationsPolicies control how wireless clients access the network. The following list contains some key areas of policy-level configurations and relevant commands.•QoS settingsqos { classifier-map | classifier-profile | marker-map | marker-profile | policy } …•User profilesuser-profile string …• SSIDs ssid string …• AAA (authentication, authorization, and accounting) settings for IEEE 802.1X authenticationaaa radius-server …While the configuration of most HiveOS features involves one or more related commands, to define and apply a QoS policy to a group of users, you must configure several different but related features: a QoS policy, a user profile, and—if you do not authenticate users with a RADIUS server—an SSID that references the user profile, and a subinterface to which you assign the SSID. The configuration steps are shown in Figure 2.Figure 2  Steps for Configuring and Applying QoSuser-profile string qos-policy string vlan-id number attribute number23144User accounts are stored on the RADIUS Server.Returned Attributes•  Tunnel Type = GRE (value = 10)•  Tunnel Medium Type = IPv4 (value = 1)•  Tunnel Private Group ID = user_profile_numberFirst, configure a QoS policy that you want to apply to wireless traffic from a group of users.The HiveAP applies the QoS policy to all wireless clients that associate with the SSID.ssid stringssid string default- user-profile-attr number3The attributes indicate which user profile to apply to the user, and the profile in turn indicates which QoS policy to apply.If you use a RADIUS server, configure it to return attributes for the realm to which the wireless users belong. After authenticating a user, the server returns these attributes with the Access-Accept message. The attributes indicate which user profile to apply to the user, and the profile in turn indicates the QoS policy to apply.qos policy string ...interface interface ssid stringSecond, configure a user profile that references the QoS policy you just configured.Assign the SSID to an interface.RADIUS Server?NoYesThe next step depends on whether you use a RADIUS server to authenticate users. If you do not use a RADIUS server, create an SSID that specifies the user profile attr bute as its default user profile.
Deployment Guide 157 HIVEOS CONFIGURATION FILE TYPESHIVEOS CONFIGURATION FILE TYPESHiveOS supports several types of configuration files: running, current, backup, bootstrap, default, and failed.The running configuration (config) is the configuration that is actively running in DRAM. During the bootup process, a HiveAP loads the running config from one of up to four config files stored in flash memory:•current: a flash file containing a combination of default and admin-defined settings. During the bootup process, this is the first config that the HiveAP attempts to load as the running config. This is also the file to which you typically save commands from the running config (you can also save them to the bootstrap config). See Figure 3.•backup: a flash file that the HiveAP attempts to load during the reboot process if there is a newly uploaded current config file or if it cannot load the current config file. See Figure 4 on page 158 and Figure 5 on page 158.•bootstrap: a flash file containing a second config composed of a combination of default and admin-defined settings. The HiveAP fails over to this config when you enter the reset config command or if both the current and backup config files fail to load. See Figure 6 on page 160.•default: a flash file containing only default settings. If there is no bootstrap config, the HiveAP reverts to this config when you enter the reset config command or if both the current and backup config files fail to load. See Figure 6 on page 160.When using the CLI, the two most frequently accessed config types are the running config and current config. When you enter a command in the running config, the HiveAP performs it immediately. However, because the running config is stored in volatile memory (DRAM), the commands are not yet permanent and will be lost when the HiveAP next reboots. For your configuration settings to persist after rebooting, enter the save config command. This command saves the running config to the current config, which is a file stored in nonvolatile (flash) memory. See Figure 3.Figure 3  Relationship between Running and Current Config FilesNote: There is also a failed config file, which holds any backup config that fails to load. See Figure 5 on page 158.(Note: The commands in  o  bold have not yet been saved, which is why they do not appear in the current config.)Current Config (in flash memory)Running Config (in DRAM)The running config comprises the current config plus any commands that have not yet been saved. The running config runs in DRAM.The current config comprises saved commands plus default settings. The current config is stored in flash memory.Running Config New Current ConfigPrevious Current Config (overwritten)When you enter the a e co fig save config command, the HiveAP saves the running config from DRAM to flash memory, where it becomes the new current config, replacing the one previously there.save config(Note: After entering the  a e save onfigconfig command, the current and running configs become identical.)
Chapter 10 HiveOS158 AerohiveWhen you upload a configuration file from HiveManager or from a TFTP or SCP server, the HiveAP stores the uploaded file in the backup config partition in flash memory, where it remains until the HiveAP reboots. If there is a backup config file already stored in flash, the newly uploaded file overwrites it. See Figure 4.Figure 4  Relationship between Current and Backup Config Files during a File UploadWhen the HiveAP reboots, it attempts to load the the newly uploaded config file. If the file loads successfully, the HiveAP makes that file the new current config and makes the previous current config the new backup config. If the file does not load successfully, the HiveAP reboots again and loads the previous current config file. The HiveAP saves the file it was unable to load as a failed config for diagnostics. See Figure 5.Figure 5  Relationship between Current and Backup Config Files while Rebooting a HiveAPConfig File Current ConfigWhen you upload a config file from HiveManager or a TFTP or SCP server, the HiveAP saves the uploaded file as a backup config. This file replaces any previous  backup config file that might have been there.TFTP ServerSCP ServerHiveManager or or HiveAPPrevious Backup Config(overwritten)New Backup Config (in flash memory)Current Config (existing config)Backup Config (newly uploaded config file)After uploading a new config file, the following two config files are stored in flash memory on the HiveAP:When you reboot the HiveAP, it tries to load the backup config. Either of the following two results can occur:If the newly loaded config file loads successfully, . . .. . . it becomes the new current config, and . . . . . . the previous current config becomes the new backup config. . . . the backup config is saved as a failed config (for diagnostic analysis). . . . the HiveAP reboots again, loads the previous current config, and . . . If the newly loaded config file fails to load, . . .Reboot the HiveAP
Deployment Guide 159 HIVEOS CONFIGURATION FILE TYPESWhen a HiveAP ships from the factory, it is loaded with a default config file, which acts initially as the running and current configs. If you enter and save any commands, the HiveAP then stores a separate config file as the current config, combining the default settings with the commands you entered and saved. If you want to return to the default settings, you can press the reset button (see "Reset Button" on page 27) or enter the reset config command. A HiveAP might also return to the default config if both the current and backup configs fail to load, which might happen if you update the HiveOS firmware to an image that cannot work with either config.Reverting to the default config can be very useful, especially in the early stages when you are still learning about HiveOS and are likely to be experimenting with different settings. However, retaining the ability of a HiveAP to revert to its default settings after its deployment can present a problem if it is a mesh point in a hive. If the HiveAP reverts to the default config, it will not be able to rejoin its hive. Consequently, it will not be able to get an IP address through DHCP nor be able to communicate with HiveManager (assuming that you are managing it through HiveManager). In this case, you would have to make a serial connection to the console port on the HiveAP and reconfigure its hive settings through the CLI.To avoid the above situation, you can use a bootstrap config. A bootstrap config is typically a small config file that comes last in the boot order (current – backup – bootstrap) and that replaces the default config as the one a HiveAP loads when you reset the configuration. See Figure 6 on page 160.Note: To upload and activate a config file from HiveManager , see "Uploading HiveAP Configurations" on page 150. To upload and activate a config file from a TFTP or SCP server using the CLI, use the following commands:save config tftp://ip_addr:filename current { hh:mm:ss |  now | offset hh:mm:ss }save config scp://username@ip_addr:filename current { hh:mm:ss | now | offset hh:mm:ss }Note: You can disable the ability of the reset button to reset the configuration by entering this command: no reset-button reset-config-enableNote: Be careful to remember the login name and password defined in the bootstrap config file. If they become lost or forgotten, you must obtain a one-time login key from Aerohive technical support. To get the key, you must already have had a support contract in place. The first one-time login key is free. After that, there is a small handling fee for each additional key.
Chapter 10 HiveOS160 AerohiveFigure 6  Relationship of Current, Backup, Bootstrap, and Default Config FilesTo create and load a bootstrap config, make a text file containing a set of commands that you want the HiveAP to load as its bootstrap configuration (for an example, see "Loading a Bootstrap Configuration" on page 179). Save the file locally and then load it with one of the following commands:save config tftp://ip_addr:filename bootstrapsave config scp://username@ip_addr:filename bootstrapAfter it is loaded, you can enter the following command to view the bootstrap file: show config bootstrapIf you want to run the bootstrap config, enter the following commands:load config bootstraprebootWhen the bootstrap config loads, enter the login parameters you defined for that configuration. To return to your previous current config file, enter the following commands:load config backuprebootNote: Similar to the way that a current config consists of the commands you added on top of the default config, a bootstrap config consists of default definitions and settings plus whatever other settings you configure.When you enter the reset  fig reset config command or press the reset button on the front panel of the HiveAP device, the HiveAP deletes the previous current config, reboots, and loads the bootstrap config— if present—or the default config. reset configCurrent Config Bootstrap ConfigDefault Config. . . or if there is no bootstrap config . . .Resetting the ConfigurationCurrent Config Backup Config Bootstrap ConfigDefault Config. . . or if there is no bootstrap config . . .If the HiveAP cannot load either the current or backup config files, it deletes them, reboots, and loads the bootstrap config— if present—or the default config. Configuration Failover Behavior Failover Failover
Deployment Guide 161Chapter 11 Deployment Examples (CLI)This chapter presents several deployment examples to introduce the primary tasks involved in configuring HiveAPs through the HiveOS CLI.In "Deploying a Single HiveAP" on page 162, you deploy one HiveAP as an autonomous access point. This is the simplest configuration: you only need to enter and save three commands.In "Deploying a Hive" on page 165, you add two more HiveAPs to the one deployed in the first example to form a hive with three members. The user authentication method in this and the previous example is very simple: a preshared key is defined and stored locally on each HiveAP and on each wireless client.In "Using IEEE 802.1X Authentication" on page 170, you change the user authentication method. Taking advantage of existing Microsoft AD (Active Directory) user accounts, the HiveAPs use IEEE 802.1X EAP (Extensible Authentication Protocol) to forward authentication requests to a RADIUS server whose database is linked to that of the AD server.In "Applying QoS" on page 173, you apply QoS (Quality of Service) filters to user traffic so that delay-sensitive voice traffic receives higher priority than other more delay-resistant traffic.In "Loading a Bootstrap Configuration" on page 179, you load a bootstrap config file on the HiveAPs. When a bootstrap config is present, it loads instead of the default config whenever HiveOS is reset or if the current and backup configs do not load. This example shows how using a bootstrap config can help minimize theft and increase convenience.Because each example builds on the previous one, it is recommended to read them sequentially. Doing so will help build an understanding of the fundamentals involved in configuring HiveAPs.If you want to view just the CLI commands used in the examples, see "CLI Commands for Examples" on page 182. Having the commands in blocks by themselves makes it easy to copy-and-paste them at the command prompt.The following are the equipment and network requirements for these examples:•Equipment• Management system (computer) capable of creating a serial connection to the HiveAP• VT100 emulator on the management system• Serial cable (also called a "null modem cable") that ships as an option with the HiveAP product. You use this to connect your management system to the HiveAP.•Network• Layer 2 switch through which you connect the HiveAP to the wired network• Ethernet cable—either straight-through or cross-over• Network access to a DHCP server• For the third and fourth examples, network access to an AD (Active Directory) server and RADIUS serverNote: To focus attention on the key concepts of an SSID (first example), hive (second example), and IEEE 802.1X authentication (third example), QoS was intentionally omitted from these examples. However, the QoS settings you define in the last example can apply equally well to the configurations in the others.Note: You can also access the CLI by using Telnet or SSH (Secure Shell). After connecting a HiveAP to the network, make either a Telnet or SSH connection to the IP address that the DHCP server assigns the mgt0 interface.
Chapter 11 Deployment Examples (CLI)162 AerohiveEXAMPLE 1: DEPLOYING A SINGLE HIVEAPIn this example, you deploy one HiveAP (HiveAP-1) to provide network access to a small office with 15 – 20 wireless clients. You only need to define the following SSID (service set identifier) parameters on the HiveAP and clients:•SSID name: employee•Security protocol suite: WPA-auto-psk• WPA – Uses Wi-Fi Protected Access, which provides dynamic key encryption and mutual authentication of the client and HiveAP• Auto – Automatically negotiates WPA or WPA2 and the encryption protocol: AES (Advanced Encryption Standard) or TKIP (Temporal Key Integrity Protocol)• PSK – Derives encryption keys from a preshared key that the client and HiveAP both already have•Preshared key: N38bu7Adr0n3After defining SSID "employee" on HiveAP-1, you then bind it to the wifi0 interface, which is in access mode by default. The wifi0 interface operates at 2.4 GHz (in accordance with the IEEE 802.11b, g, and n standards). This example assumes that the clients also support 802.11b, g, or n.Figure 1  Single HiveAP for a Small Wireless NetworkStep 1 Log in through the console port1. Connect the power cable from the DC power connector on the HiveAP to the AC/DC power adaptor that ships with the device as an option, and connect that to a 100 – 240-volt power source.The Power LED glows steady amber during the bootup process. After the bootup process completes, it then glows steady green to indicate that the firmware is loaded and running.2. Connect one end of an RS-232 serial (or "null modem") cable to the serial port (or Com port) on your management system.3. Connect the other end of the cable to the male DB-9 or RJ-45 console port on the HiveAP.Note: By default, the wifi1 interface is in backhaul mode and operates at 5 GHz to support IEEE 802.11a. To put wifi1 in access mode so that both interfaces provide access—the wifi0 interface at 2.4 GHz and the wifi1 interface at 5 GHz—enter this command: interface wifi1 mode access. Then, in addition to binding SSID "employee" to wifi0 (as explained in step 2), also bind it to wifi1.Note: If the switch supports PoE (Power over Ethernet), the HiveAP can receive its power that way instead.Wireless Network-1HiveAP-1 Switch FirewallInternetDHCP ServerWireless clients associate with HiveAP-1 using SSID "employee" with the security suite WPA-auto-psk (PSK = N38bu7Adr0n3).The wireless clients and the mgt0 interface on HiveAP-1 receive their IP addresses and associated TCP/IP settings from the DHCP server.Wired Networkwifi0 interfaceSSID "employee"Access mode IEEE 802.11b/g/nPhysical interface: eth0Logical interface: mgt0Backhaul modeNetwork portal
Deployment Guide 163EXAMPLE 1: DEPLOYING A SINGLE HIVEAP4. On your management system, run a VT100 terminal emulation program, such as Tera Term Pro© (a free terminal emulator) or Hilgraeve Hyperterminal® (provided with Windows® operating systems). Use the following settings:• Bits per second (baud rate): 9600• Data bits: 8• Parity: none•Stop bits: 1• Flow control: noneFor HiveAPs set with "FCC" as the region code, the Initial CLI Configuration Wizard appears. For HiveAPs set with "world" as the region code, a prompt appears to set the country code for the location where you intend to deploy the HiveAP. To set the country code, enter the boot-param country-code number command, in which number is the appropriate country code number. For a list of country codes, see "Appendix A Country Codes" on page 189.5. Because you do not need to configure all the settings presented in the wizard, press N to cancel it.The login prompt appears.6. Log in using the default user name admin and password aerohive.Step 2 Configure the HiveAP1. Create an SSID and assign it to an interface.ssid employeessid employee security protocol-suite wpa-auto-psk ascii-key N38bu7Adr0n3You first create an SSID named "employee" and then define its protocol suite and preshared key (N38bu7Adr0n3) in standard ASCII (American Standard Code for Information Interchange) text.interface wifi0 ssid employeeYou assign the SSID to the wifi0 interface, which is in access mode by default. When you make this assignment, the HiveAP automatically creates subinterface wifi0.1 and uses that for the SSID. (The HiveAP 20 series supports up to seven subinterfaces per Wi-Fi interface for a possible maximum total of 14 SSIDs when both wifi0 and wifi1 are in access mode. The HiveAP 300 series supports up to eight per interface for a possible maximum total of 16.) A HiveAP can use one or two Wi-Fi interfaces in access mode to communicate with wireless clients accessing the network, and a Wi-Fi interface in backhaul mode to communicate wirelessly with other HiveAPs when in a hive (see subsequent examples).2. (Optional) Change the name and password of the root admin.admin root-admin mwebster password 3fF8haAs a safety precaution, you change the default root admin name and password to mwebster and 3fF8ha. The next time you log in, use these instead of the default definitions.3. (Optional) Change the host name of the HiveAP.hostname HiveAP-14. Save your changes to the currently running configuration, and then log out of the serial session.save configexitThe HiveAP configuration is complete.Note: By default, the minimum password length is 5 characters. You can change the minimum length by entering the following command: admin min-password-length <number> (The minimum password length can be between 5 and 16 characters.)
Chapter 11 Deployment Examples (CLI)164 AerohiveStep 3 Configure the wireless clientsDefine the "employee" SSID on all the wireless clients. Specify WPA-PSK for network authentication, AES or TKIP for data encryption, and the preshared key N38bu7Adr0n3.Step 4 Position and power on the HiveAP1. Place the HiveAP within range of the wireless clients and, optionally, mount it as explained in the mounting section in the chapter about the HiveAP model that you are using.2. Connect an Ethernet cable from the PoE In port to the network switch.3. If you have powered off the HiveAP, power it back on by reconnecting it to a power source.When you power on the HiveAP, the mgt0 interface, which connects to the wired network through the eth0 port, automatically receives its IP address through DHCP (Dynamic Host Configuration Protocol).Step 5 Check that clients can form associations and access the network1. To check that a client can associate with the HiveAP and access the network, open a wireless client application and connect to the "employee" SSID. Then contact a network resource, such as a web server.2. Log in to the HiveAP CLI, and check that you can see the MAC address of the associated client and an indication that the correct SSID is in use by entering the following command:The setup of a single HiveAP is complete. Wireless clients can now associate with the HiveAP using SSID "employee" and access the network.Note: You can also enter the following commands to check the association status of a wireless client: show auth, show roaming cache, and show roaming cache mac <mac_addr>.Check that the MAC address in the table matches that of the wireless client .Check that the authentication and encryption modes match those in the SSID security protocol suite.show ssid employee stationChan=channel number; Pow=Power in dbm;A-Mode=Authentication mode; Cipher=Encryption mode;A-Time=Associated time; Auth=Authenticated;UPID=User profile Identifier; Phymode=Physical mode;Mac Addr  IP Addr  Chan  Rate  Pow  A-Mode  Cipher  A-Time  VLAN  Auth  UPID  Phymode-------------- --------- ---- ---- ---- -------- -------  -------- ---- ---- ---- -------0016:cf8c:57bc 10.1.1.35 11  54M  -38  wpa2-psk  aes ccm  00:00:56  1  Yes  0  11g
Deployment Guide 165EXAMPLE 2: DEPLOYING A HIVEEXAMPLE 2: DEPLOYING A HIVEBuilding on "Deploying a Single HiveAP" on page 162, the office network has expanded and requires more HiveAPs to provide greater coverage. In addition to the basic configuration covered in the previous example, you configure all three HiveAPs to form a hive within the same layer 2 switched network. The following are the configuration details for the hive:•Hive name: hive1•Preshared key for hive1 communications: s1r70ckH07m3sHiveAP-1 and -2 are cabled to a switch and use the native ("untagged") VLAN for wired backhaul communications. They communicate with each other over both wired and wireless backhaul links, the wired link taking precedence. However, HiveAP-3 only communicates with HiveAP-1 and -2 over a wireless link (see Figure 2). Because HiveAP-1 and -2 connect to the wired network, they act as portals. In contrast, HiveAP-3 is a mesh point.Figure 2  Three HiveAPs in a HiveNote: The security protocol suite for hive communications is WPA-AES-psk.Note: If all hive members can communicate over wired backhaul links, you can then use both radios for access. The wifi0 interface is already in access mode by default. To put wifi1 in access mode, enter this command: interface wifi1 mode access. In this example, however, a wireless backhaul link is required.Wireless Network-1SwitchFirewallInternetDHCP ServerWireless Network-2 Wireless Network-3Wired Hive Backhaul CommunicationsHiveAP-1 (Portal)HiveAP-2 (Portal) HiveAP-3 (Mesh Point)Wireless Hive Backhaul CommunicationsWireless Network Access ConnectionsHiveAP-1 and HiveAP-2 are portals and use both wired and wireless backhaul methods to communicate with each other. HiveAP-3 is a mesh point, using only a wireless connection for backhaul communications with the other two hive members.Wired Ethernet Network ConnectionsHive1
Chapter 11 Deployment Examples (CLI)166 AerohiveStep 1 Configure HiveAP-11. Using the connection settings described in the first example, log in to HiveAP-1.2. Configure HiveAP-1 as a member of "hive1" and set the security protocol suite.hive hive1You create a hive, which is a set of HiveAPs that collectively distribute data and coordinate activities among themselves, such as client association data for fast roaming, route data for making optimal data-path forwarding decisions, and policy enforcement for QoS (Quality of Service) and security.hive hive1 password s1r70ckH07m3sYou define the password that hive members use to derive the preshared key for securing backhaul communications with each other. The password must be the same on all hive members.interface mgt0 hive hive1By setting "hive1" on the mgt0 interface, you join HiveAP-1 to the hive.save config3. Before closing the console session, check the radio channel that HiveAP-1 uses on its backhaul interface, which by default is wifi1:HiveAP-1 is set to use wireless interface wifi1 and its subinterface wifi1.1 for backhaul communications.Write down the radio channel for future reference (in this example, it is 149). When configuring HiveAP-2 and -3, make sure that they also use this channel for backhaul communications.exitThe wifi1 interface and the wifi1.1 subinterface are in backhaul mode and are using channel 149. Both wifi1 and wifi1.1 use the default radio profile radio_na0. (Depending on the HiveAP model, the default profile might be radio_a0.) This is a profile for radio2, which operates in the 5 GHz frequency range as specified in the IEEE 802.11a and n standards.show interfaceState=Operational state; Chan=Channel;Radio=Radio profile; U=up; D=down;Name MAC addr  Mode  State Chan VLAN Radio Hive SSID------- -------------- -------- ----- ---- ---- -------- ----- --------Mgt0  0019:7700:0020     -  U  -  1    -  hive1    -Eth0  0019:7700:0020  backhaul  U  -  1    -  hive1    -Wifi0  0019:7700:0024  access  U  11  -  radio_ng0    -    -Wifi0.1 0019:7700:0024 access  U  11  -  radio_ng0 hive1 employeeWifi1  0019:7700:0028  backhaul  U  149  -  radio_na0    -    -Wifi1.1  0019:7700:0028  backhaul  U  149  1  radio_na0  hive1    -
Deployment Guide 167EXAMPLE 2: DEPLOYING A HIVEStep 2 Configure HiveAP-2 and HiveAP-31. Power on HiveAP-2 and log in through its console port.2. Configure HiveAP-2 with the same commands that you used for HiveAP-1:ssid employeessid employee security protocol-suite wpa-auto-psk ascii-key N38bu7Adr0n3interface wifi0 ssid employeehive hive1hive hive1 password s1r70ckH07m3sinterface mgt0 hive hive13. (Optional) Change the name and password of the superuser.admin superuser mwebster password 3fF8ha4. Check that the channel ID for wifi1 and wifi1.1 is now 149.show interfaceIf the channel ID for wifi1 and wifi1.1 is not 149, set it to 149 so that HiveAP-2 uses the same channel as HiveAP-1 for backhaul communications.interface wifi1 radio channel 149Setting the channel for the parent interface (wifi1) sets it for all its subinterfaces. An interface in backhaul mode only needs one subinterface, which by default is wifi1.1.save configexit5. Repeat the above steps for HiveAP-3.Step 3 Connect HiveAP-2 and HiveAP-3 to the network1. Place HiveAP-2 within range of its clients and within range of HiveAP-1. This allows HiveAP-1 and -2 to send backhaul communications to each other wirelessly as a backup path in case either member loses its wired connection to the network.2. Connect an Ethernet cable from the PoE In port on HiveAP-2 to the network switch.3. Power on HiveAP-2 by connecting it to a power source.After HiveAP-2 finishes booting up (indicated when the Power LED changes from steady amber to steady green), it automatically discovers another member of hive1 (HiveAP-1). The two members use a preshared key based on their shared secret (s1r70ckH07m3s) to authenticate each other and AES to encrypt wired backhaul communications and AES-CCMP to encrypt wireless backhaul communications between themselves. You can tell when they have formed a hive because the Mesh LED changes its blinking pattern from a fast to slow.4. Place HiveAP-3 within range of its wireless clients and one or both of the other hive members.5. Power on HiveAP-3 by connecting it to a power source.
Chapter 11 Deployment Examples (CLI)168 AerohiveAfter HiveAP-3 boots up, it discovers the two other members of hive1 over a wireless backhaul link. The members authenticate themselves and establish a security association for encrypting backhaul communications among themselves. HiveAP-3 then learns its default route to the wired network from the other hive members. If the other members send routes with equal costs—which is what happens in this example—HiveAP-3 uses the first route it receives. When it learns this route, it can communicate with the DHCP server to get an IP address for its mgt0 interface.6. Check that HiveAP-3 has associated with the other members at the wireless level.HiveAP-20019:7700:0438wifi1.1 MAC AddressHiveAP-10019:7700:0028wifi1.1 MAC Addressshow hive hive1 neighborChan=channel number; Pow=Power in dBm;A-Mode=Authentication mode; Cipher=Encryption mode;Conn-Time=Connected time; Hstate=Hive State;Mac Addr  Chan  Tx Rate  Rx Rate  Pow  A-Mode  Cipher  Conn-Time  Hstate  Phymode  Hive-------------- ----  -------  -------  ---  ------  -------  ---------  ------  ------- ----0019:7700:0028 149  54M  54M  -16  psk  aes ccm  00:04:15  Auth  11a  hive10019:7700:0438 149  54M  54M  -16  psk  aes ccm  00:04:16  Auth  11a  hive1Log in to HiveAP-3 and enter this command to see its neighbors in hive1:HiveAP-3In the output of the show hive hive1 neighbor command, you can see hive-level and member-level information. (On HiveAPs supporting 802.11n, the channel width for hive communications—20 or 40 MHz—is also shown.)When you see the MAC addresses of the other hive members, you know that HiveAP-3 learned them over a wireless backhaul link.NeighborsThe following are the various hive states that can appear:Disv (Discover) - Another HiveAP has been discovered, but there is a mismatch with its hive ID.Neibor (Neighbor) -  Another HiveAP has been discovered whose hive ID matches, but it has not yet been authenticated. CandPr (Candidate Peer) - The hive ID on a discovered HiveAP matches, and it can accept more neighbors.AssocPd (Association Pending) - A HiveAP is on the same backhaul channel, and an assocation process in progress.Assocd (Associated) - A HiveAP has associated with the local HiveAP and can now start the authentication process.Auth (Authenticated) - The HiveAP has been authenticated and can now exchange data traffic.
Deployment Guide 169EXAMPLE 2: DEPLOYING A HIVE7. To check that the hive members have full data connectivity with each other, associate a client in wireless network-1 with HiveAP-1 (the SSID "employee" is already defined on clients in wireless network-1; see "Deploying a Single HiveAP"). Then check if HiveAP-1 forwards the client’s MAC address to the others to store in their roaming caches.This MAC address is for the wireless adapter of the client (or “supplicant”) associated with the SSID “employee”.This MAC address is for the wifi0.1 subinterface of HiveAP-1, the HiveAP with which the wireless client associated.This is the same MAC address for the client (station) that you saw listed on HiveAP-1.After associating a wireless client with HiveAP-1, log in to HiveAP-1 and enter this command:When you see the MAC address of the wireless client that is associated with HiveAP-1 in the roaming cache of HiveAP-2, you know that HiveAP-1 and -2 are successfully sending data over the backhaul link.Repeat this to confirm that HiveAP-3 also has a backhaul connection with the other members.Then log in to HiveAP-2 and enter this command:HiveAP-1HiveAP-2show roaming cacheRoaming Cache Table:UID=User profile group ID; PMK=Pairwise Master Key;TLC=PMK Time Left in Cache; Life=PMK Life; A=authenticated; L= CWP Logged InRoaming for this HiveAP: enabledMaximum Caching Time:  3600 secondsCaching update interval: 60 secondsCaching update times:  60Roaming hops:  1SSID employee:Maximum Caching Time:  3600 secondsCaching update interval: 60 secondsCaching update times:  60No. Supplicant  Authenticator  UID PMK  PMKID Life  Age  TLC  Hop  AL--- -------------- -------------- --- ----- ----- ----  -----  ---  ---  --0 0016:cf8c:57bc 0019:7700:0024 0 1349* 1615* -1   46  195 1  YNshow ssid employee stationChan=channel number; Pow=Power in dBm;A-Mode=Authentication mode; Cipher=Encryption mode;A-Time=Associated time; Auth=Authenticated;UPID=User profile Identifier; Phymode=Physical mode;Mac Addr  IP Addr  Chan  Tx Rate  Rx Rate  Pow  A-Mode  Cipher  A-Time  VLAN  Auth UPID  Phymode--------------  ---------- ---- -------  ------- --- -------- ------- -------- ---- ---- ---- -------0016:cf8c:57bc  10.1.1.73     1      54M      54M  -40  wpa2-psk  aes ccm 00:01:46     1  Yes     0  11b/gTotal station count: 1Note: On HiveAPs supporting IEEE 802.11n, there are two additional columns for SM-PS (spatial multiplexing power save) and channel width (20 or 40 MHz).  The SM-PS states can be “static” (use one data stream for 11a/b/g clients), “dynamic” (use multiple spatial streams for 11n clients when the HiveAP sends an RTS frame), or “disabled” (always use spatial streams for 11n clients).
Chapter 11 Deployment Examples (CLI)170 AerohiveStep 4 Configure wireless clientsDefine the "employee" SSID on all the wireless clients in wireless network-2 and -3. Specify WPA-PSK for network authentication, AES or TKIP for data encryption, and the preshared key N38bu7Adr0n3.The setup of hive1 is complete. Wireless clients can now associate with the HiveAPs using SSID "employee" and access the network. The HiveAPs communicate with each other to share client associations (to support fast roaming) and routing data (to select optimal data paths).EXAMPLE 3: USING IEEE 802.1X AUTHENTICATIONIn this example, you use a Microsoft AD (Active Directory) server and a RADIUS server to authenticate wireless network users. To accomplish this, you make the following modifications to the hive set up in "Deploying a Hive":• Configure settings for the RADIUS server on the HiveAPs• Change the SSID parameters on the HiveAPs and wireless clients to use IEEE 802.1XThe basic network design is shown in Figure 3.Figure 3  Hive and 802.1X AuthenticationWireless Network-1SwitchFirewallInternetDHCP ServerWireless Network-2 Wireless Network-3Wired Hive Backhaul CommunicationsHiveAP-1HiveAP-2 HiveAP-3Wireless Hive Backhaul CommunicationsWireless Network Access ConnectionsThe HiveAPs receive PEAP (Protected EAP) authentication requests from clients and forward them inside RADIUS authentication packets to the RADIUS server at 10.1.1.10. The RADIUS server is in turn linked to the database of the Active Directory server on which all the user accounts have previously been created and stored.RADIUS Server10.1.1.10Active Directory ServerWired Ethernet Network ConnectionsHive1
Deployment Guide 171EXAMPLE 3: USING IEEE 802.1X AUTHENTICATIONStep 1 Define the RADIUS server on the HiveAP-1Configure the settings for the RADIUS server (IP address and shared secret) on HiveAP-1.aaa radius-server first 10.1.1.10 shared-secret s3cr3741n4bl0X The IP address of the RADIUS server is 10.1.1.10, and the shared secret that HiveAP-1 and the RADIUS server use to authenticate each other is "s3cr3741n4b10X". You must also enter the same shared secret on the RADIUS server when you define the HiveAPs as access devices (see step 5).Step 2 Change the SSID on HiveAP-11. Change the authentication method in the SSID.ssid employee security protocol-suite wpa-auto-8021xsave configThe protocol suite requires WPA (Wi-Fi Protected Access) or WPA2 security protocol for authentication and key management, AES or TKIP encryption, and user authentication through IEEE 802.1X.2. Enter the show interface mgt0 command and note the dynamically assigned IP address of the mgt0 interface. You need to know this address to define HiveAP-1 as an access device on the RADIUS server in step 5.exitStep 3 Configure HiveAP-2 and HiveAP-31. Log in to HiveAP-2 through its console port.2. Configure HiveAP-2 with the same commands that you used for HiveAP-1:aaa radius-server first 10.1.1.10 shared-secret s3cr3741n4bl0Xssid employee security protocol-suite wpa-auto-8021xsave config3. Enter the show interface mgt0 command to learn its IP address. You need this address for step 5.exit4. Log in to HiveAP-3 and enter the same commands.Step 4 Modify the SSID on the wireless clientsModify the "employee" SSID on all the wireless clients in wireless network-2 and -3. Specify WPA or WPA2 for network authentication, AES or TKIP for data encryption, and PEAP (Protected EAP) for user authentication.Note: This example assumes that the RADIUS and AD servers were previously configured and populated with user accounts that have been in use on a wired network (not shown). The only additional configuration on these servers is to enable the RADIUS server to accept authentication requests from the HiveAPs.Note: Although all HiveAPs in this example use the same shared secret, they can also use different secrets.
Chapter 11 Deployment Examples (CLI)172 AerohiveStep 5 Configure the RADIUS Server to accept authentication requests from the HiveAPsLog in to the RADIUS server and define the three HiveAPs as access devices. Enter their mgt0 IP addresses (or fully-qualified domain names) and shared secret.Step 6 Check that clients can form associations and access the network1. To check that a client can associate with a HiveAP and access the network, open a wireless client application and connect to the "employee" SSID. Then contact a network resource, such as a web server.2. Log in to the HiveAP CLI, and check that you can see the MAC address or the associated client and an indication that the correct SSID is in use by entering the following command:The setup for using IEEE 802.1X is complete. Wireless clients can now associate with the HiveAP using SSID "employee", authenticate themselves through IEEE 802.1X to a RADIUS server, and access the network.Note: You can also enter the following commands to check the association status of a wireless client: show auth, show roaming cache, and show roaming cache mac <mac_addr>.Check that the MAC and IP addresses in the table match those of the wireless client .Check that the authentication and encryption modes match those in the SSID security protocol suite.show ssid employee stationChan=channel number; Pow=Power in dBm;A-Mode=Authentication mode; Cipher=Encryption mode;A-Time=Associated time; Auth=Authenticated;UPID=User profile Identifier; Phymode=Physical mode;Mac Addr  IP Addr  Chan  Tx Rate  Rx Rate  Pow  A-Mode  Cipher  A-Time  VLAN  Auth UPID  Phymode--------------  ---------- ---- -------  ------- --- -------- ------- -------- ---- ---- ---- -------0016:cf8c:57bc  10.1.1.73     1      54M      54M  -40  8021x  aes ccm 00:02:34     1  Yes     0  11b/gTotal station count: 1
Deployment Guide 173EXAMPLE 4: APPLYING QOSEXAMPLE 4: APPLYING QOSIn this example, you want the hive members to prioritize voice, streaming media, and e-mail traffic. First, you map distinguishing elements of these traffic types to three Aerohive QoS (Quality of Service) classes:Class 6: voice traffic from VoIP phones with MAC OUI 00:12:3b (the OUI for all phones in the network)Voice traffic is very sensitive to delay and cannot tolerate packet loss without loss of voice quality. When other traffic is competing with voice traffic for bandwidth, it becomes essential to prevent that traffic from interfering with voice traffic. Because voice traffic for a single call requires very little bandwidth—typically from 8 to 64 Kbps depending on the voice codec used—a good approach for setting its rate is to calculate the bandwidth necessary for a voice call plus related telephony traffic from a single user’s computer, softphone, or handset and then multiply that by the potential number of concurrent VoIP users.Class 5: streaming media using the MMS (Microsoft Media Server) protocol on TCP port 1755Although streaming media is also time sensitive, streaming media software for both clients and servers offers limited buffering to prevent choppy sounds and pixelated video when network congestion occurs. Because congestion for more than a few seconds can adversely effect streaming media, it is important to assign this type of traffic a higher priority than other types, but its priority should be lower than that for voice, which is even more sensitive to delay.Class 3: data traffic for e-mail using the following protocols:SMTP (Simple Mail Transfer Protocol) on TCP port 25POP3 (Post Office Protocol version 3) on TCP port 110Then you create classifier profiles that reference these traffic-to-class mappings. You bind the profiles to the wifi0.1 and eth0 interfaces so that hive members map the traffic matching these profiles that arrives at these interfaces to the proper Aerohive classes.You next define a QoS policy that defines how the hive members prioritize and process the traffic mapped to Aerohive classes 6, 5, and 3. The QoS policy (named "voice") is shown in Figure 4 on page 174 and has these settings:Class 6 (voice)Forwarding: strict (Hive members forward traffic mapped to this class immediately without queuing it.)Maximum rate for all class 6 traffic: 512 Kbps, which supports an 8- to 64-Kbps VoIP call (depending on the compression that the codec provides) plus other telephony traffic such as DHCP, DNS, HTTP, and TFTP.Class 5 (streaming media)Forwarding: WRR (weighted round robin) with a weight of 90By assigning class 5 a higher weight (90) than class 3 and 2 weights (class 3 = 60, class 2 = 30), you give streaming media roughly a 3:2 priority over class 3 traffic and a 3:1 priority over class 2 traffic.Maximum traffic rate for all class 5 traffic: 20,000 KbpsYou change the bandwidth available for streaming media when there is no competition for it (the default rate for class 5 is 10,000 Kbps on HiveAPs that do not support the IEEE 802.11n standard and 50,000 Kbps on HiveAPs that do. However, you do not set the maximum rate (54,000 or 1,000,000 Kbps, depending on the HiveAP model that you are configuring) to ensure that streaming media does not consume all available bandwidth even if it is available.Class 3 (e-mail)Forwarding: WRR with a weight of 60To help ensure that e-mail traffic remains flowing even when other types of data traffic compete with it for available bandwidth, you elevate its priority by mapping SMTP and POP3 traffic to class 3 and giving that class a higher weight (60) than the weight for class 2 traffic (30).Maximum traffic rate for all class 3 traffic: 54,000 or 1,000,000 Kbps (the default, depending on the HiveAP)
Chapter 11 Deployment Examples (CLI)174 AerohiveFigure 4  QoS Policy "voice" for Voice, Streaming Media, and DataFinally, you create a user profile "employee-net" and apply the QoS policy "voice" to the user profile on each hive member. You also configure the RADIUS server to return attributes in its authentication responses to indicate the user group to which the hive members then assign users.Note: The HiveAP assigns all traffic that you do not specifically map to an Aerohive class to class 2, which by default uses WRR with a weight of 30 and a rate of 54,000 or 1,000,000 Kbps, depending on the HiveAP.Note: This example assumes that the RADIUS and AD servers were previously configured and populated with user accounts and have been serving a wired network (not shown). The only additional configuration is to enable the RADIUS server to accept authentication requests from the HiveAPs.qos policy voice qos 6 strict 512 0The policy assigns the highest priority to voice traffic (class 6).  For each voice session up to 512 Kbps, hive members provide “strict” forwarding; that is, they forward traffic immediately without queuing it.Voiceqos policy voice qos 5 wrr 20000 90Because streaming media (class 5) needs more bandwidth than voice does, the policy defines a higher forwarding rate for it: 20,000 Kbps. It sorts streaming media into forwarding queues using the WRR (weighted round robin) mechanism. It also prioritizes streaming media by assigning a higher weight (90) than it assigns data traffic (class 3 = 60, class 2 = 30).Streaming Mediaqos policy voice qos 3 wrr { 54000 | 1000000 } 60qos policy voice qos 2 wrr { 54000 | 1000000 } 30*The policy sorts class 3 and 2 traffic into forwarding queues using WRR and defines the highest forwarding rate: 54,000 Kbps or 1,000,000 Kbps, depending on the HiveAP model that you are configuring. It gives class 3 (for e-mail protocols SMTP and POP3) a higher WRR weight (60) so that the HiveAP queues more e-mail traffic in proportion to other types of traffic in class 2, which has a weight of 30 by default. As a result, e-mail traffic has a better chance of being forwarded than other types of traffic when bandwidth is scarce. Class 2 is for all types of traffic not mapped to an Aerohive class—such as HTTP for example.DataQoS Policy: “voice”* You do not need to enter this command because it just sets the default values for class 2. It is shown to provide contrast with the previous command.
Deployment Guide 175EXAMPLE 4: APPLYING QOSStep 1 Map traffic types to Aerohive QoS classes on HiveAP-11. Map the MAC OUI (organizational unit identifier) of network users’ VoIP phones to Aerohive class 6.qos classifier-map oui 00:12:3b qos 6In this example, all network users use VoIP phones from the same vendor whose OUI (that is, the MAC address prefix ) is 00:12:3b. When HiveAP-1 receives traffic from a client whose source MAC address contains this OUI, it assigns it to Aerohive class 6.2. Define the custom services that you need.service mms tcp 1755service smtp tcp 25service pop3 tcp 110The MMS (Microsoft Media Server) protocol can use several transports (UDP, TCP, and HTTP). However, for a HiveAP to be able to map a service to an Aerohive QoS class, it must be able to identify that service by a unique characteristic such as a static destination port number or a nonstandard protocol number. Unlike MMS/UDP and MMS/HTTP, both of which use a range of destination ports, MMS/TCP uses the static destination port 1755, which a HiveAP can use to map the service to an Aerohive class. Therefore, you define a custom service for MMS using TCP port 1755. You also define custom services for SMTP and POP3 so that you can map them to Aerohive class 3. By doing so, you can prioritize e-mail traffic above other types of traffic that the HiveAP assigns to class 2 by default.3. Map services to Aerohive classes.qos classifier-map service mms qos 5qos classifier-map service smtp qos 3qos classifier-map service pop3 qos 3Unless you map a specific service to an Aerohive QoS class, a HiveAP maps all traffic to class 2. In this example, you prioritize voice, media, and e-mail traffic by assigning them to higher QoS classes than class 2, and then by defining the forwarding and weighting mechanisms for each class (see step 3).Step 2 Create profiles to check traffic arriving at interfaces on HiveAP-11. Define two classifier profiles for the traffic types "mac" and "service".qos classifier-profile employee-voice macqos classifier-profile employee-voice serviceqos classifier-profile eth0-voice macqos classifier-profile eth0-voice serviceClassifier profiles define which components of incoming traffic HiveAP-1 checks. Because you specify "mac" and "service", it checks the MAC address in the Ethernet frame header and the service type (by protocol number in the IP packet header and port number in the transport packet header). If it detects traffic matching a classifier-map, it maps it to the appropriate Aerohive class. However, before this can happen, you must first associate the profiles with the interfaces that will be receiving the traffic that you want checked. This you do with the next two commands.
Chapter 11 Deployment Examples (CLI)176 Aerohive2. Associate the classifier profiles with the employee SSID and the eth0 interface so that HiveAP-1 can classify incoming traffic arriving at these two interfaces.ssid employee qos-classifier employee-voiceinterface eth0 qos-classifier eth0-voiceBy creating two QoS classifiers and associating them with the employee SSID and eth0 interface, HiveAP-1 can classify traffic flowing in both directions for subsequent QoS processing; that is, it can classify traffic flowing from the wireless LAN to the wired LAN, and from the wired LAN to the wireless LAN.Step 3 Apply QoS on HiveAP-11. Create a QoS policy.For HiveAPs supporting IEEE 802.11a/b/g:qos policy voice qos 5 wrr 20000 90qos policy voice qos 3 wrr 54000 60For HiveAPs supporting IEEE 802.11a/b/g/n:qos policy voice qos 6 strict 512 0qos policy voice qos 5 wrr 20000 90qos policy voice qos 3 wrr 1000000 60By default, a newly created QoS policy attempts to forward traffic mapped to classes 6 and 7 immediately upon receipt. This immediate forwarding of received traffic is called "strict" forwarding. To assign strict forwarding to VoIP traffic from phones whose MAC OUI is mapped to class 6, you simply retain the default settings for class 6 traffic on HiveAPs supporting 802.11a/b/g data rates. For HiveAPs supporting 802.11n data rates, the default user profile rate is 20,000 Kbps for class 6 traffic, so you change it to 512 Kbps.For classes 5 and 3, you limit the rate of traffic and set WRR (weighted round robin) weights so that the HiveAP can control how to put the rate-limited traffic into forwarding queues. You use the default settings for class 2 traffic.When you enter any one of the above commands, the HiveAP automatically sets the maximum bandwidth for all members of the user group to which you later apply this policy and the bandwidth for any individual group member. You leave the maximum traffic rate at the default 54,000 Kbps or 1,000,000 Kbps—depending on the HiveAP model that you are configuring—for the user group. You also leave the maximum bandwidth for a single user at 54,000 or 1,000,000 Kbps, so that if a single user needs all the bandwidth and there is no competition for it, that user can use it all.Also by default, the traffic rate for this policy has a weight of 10. At this point, because this is the only QoS policy, the weight is inconsequential. If there were other QoS policies, then their weights would help determine how the HiveAP would allocate the available bandwidth.Note: If the surrounding network employs the IEEE 802.11p QoS classification system (for wired network traffic) or 802.11e (for wireless network traffic), you can ensure that HiveAP-1 checks for them by entering these commands: qos classifier-profile eth0-voice 8021pqos classifier-profile employee-voice 80211e
Deployment Guide 177EXAMPLE 4: APPLYING QOSThe QoS policy that you define is shown in Figure 5. Although you did not configure settings for Aerohive QoS classes 0, 1, 2, 4, and 7, the policy applies default settings to them. The HiveAP assigns all traffic that you do not specifically map to an Aerohive class to class 2, which uses WRR with a weight of 30 and a default rate of 54,000 or 1,000,000 Kbps. Because nothing is mapped to classes 0, 1, 4, and 7, their settings are irrelevant.Figure 5  QoS Policy "voice"2. Create a user profile and apply the QoS policy to it.user-profile employee-net qos-policy voice attribute 2You apply the QoS policy "voice" to all users belonging to the user-profile "employee-net" with attribute 2. On the RADIUS server, you must configure attribute 2 as one of the RADIUS attributes that the RADIUS server returns when authenticating users (see step 5 on page 179).save configexitNote: When HiveAP-1 does not use RADIUS for user authentication, you must assign the user profile to an SSID. To do that, use the following command: ssid employee default-user-profile-attr 2The user profile rate defines the total amount of bandwidth for all users to which this policy applies. The user rate defines the maximum amount for any single user. The user rate can be equal to but not greater than the user profile rate. (Note: The maximums shown here are for HiveAPs that support 802.11n data rates. For other HiveAPs, the maximum rates are 54,000 Kbps.)show qos policy voice  Policy name=voice; user rate limit=1000000kbps;User profile rate=1000000kbps; user profile weight=10;Class=0; mode=wrr; weight=10; limit=1000000kbps;Class=1; mode=wrr; weight=20; limit=1000000kbps;Class=2; mode=wrr; weight=30; limit=1000000kbps;Class=3; mode=wrr; weight=60; limit=1000000kbps;Class=4; mode=wrr; weight=50; limit=1000000kbps;Class=5; mode=wrr; weight=90; limit=20000kbps;Class=6; mode=strict; weight=0; limit=512kbps;Class=7; mode=strict; weight=0; limit=20000kbps;The forwarding mode for class 6 (voice) is strict. The HiveAP forwards packets belonging to this class immediately without queuing them.The forwarding mode for class 5 (streaming media) and 2 - 3 (data) is WRR (weighted round robin). The HiveAP forwards traffic belonging to these classes by putting them into forwarding queues. The weights determine how many bits per second go into each queue. For every 30 bits that the HiveAP queues for class 2, it queues approximately 60 bits for class 3, and 90 bits for class 5. These amounts are approximations because the HiveAP also has an internal set weights for traffic in different classes that skews forwarding in favor of traffic belonging to higher classes.
Chapter 11 Deployment Examples (CLI)178 AerohiveStep 4 Configure HiveAP-2 and HiveAP-31. Log in to HiveAP-2 through its console port.2. Configure HiveAP-2 with the same commands that you used for HiveAP-1:qos classifier-map oui 00:12:3b qos 6service mms tcp 1755service smtp tcp 25service pop3 tcp 110qos classifier-map service mms qos 5qos classifier-map service smtp qos 3qos classifier-map service pop3 qos 3qos classifier-profile employee-voice macqos classifier-profile employee-voice serviceqos classifier-profile eth0-voice macqos classifier-profile eth0-voice servicessid employee qos-classifier employee-voiceinterface eth0 qos-classifier eth0-voiceFor HiveAPs supporting IEEE 802.11a/b/g:qos policy voice qos 5 wrr 20000 90qos policy voice qos 3 wrr 54000 60For HiveAPs supporting IEEE 802.11a/b/g/n:qos policy voice qos 6 strict 512 0qos policy voice qos 5 wrr 20000 90qos policy voice qos 3 wrr 1000000 60user-profile employee-net qos-policy voice attribute 2save configexit3. Log in to HiveAP-3 and enter the same commands.
Deployment Guide 179EXAMPLE 5: LOADING A BOOTSTRAP CONFIGURATIONStep 5 Configure RADIUS server attributes 1. Log in to the RADIUS server and define the three HiveAPs as RADIUS clients.2. Configure the following attributes for the realm to which the wireless user accounts in network-1, -2, and -3 belong:• Tunnel Type = GRE (value = 10)• Tunnel Medium Type = IP (value = 1)• Tunnel Private Group ID = 2The RADIUS server returns the above attributes for all wireless users it authenticates from network-1, -2, and -3. The HiveAP uses the combination of returned RADIUS attributes to assign users to the user group 2 ("employee-net"). It does not use them to create a GRE tunnel, which the tunnel type attribute might lead you to think.When there is more traffic than available bandwidth, the HiveAP applies the "voice" policy. It performs strict forwarding for voice and uses a WRR (weighted round robin) scheduling discipline for directing streaming media and data traffic to queues to await forwarding. The QoS configuration is complete.EXAMPLE 5: LOADING A BOOTSTRAP CONFIGURATIONAs explained in "HiveOS Configuration File Types" on page 157, a bootstrap config file is typically a small set of commands to which a HiveAP can revert when the configuration is reset or if the HiveAP cannot load its current and backup configs. If you do not define and load a bootstrap config, the HiveAP reverts to the default config in these situations, which can lead to two potential problems:• If both the current and backup configs fail to load on a HiveAP acting as a mesh point in a hard-to-reach location—such as a ceiling crawlspace—the HiveAP would revert to the default config. Because a mesh point needs to join a hive before it can access the network and the default config does not contain the hive settings that the mesh point needs to join the hive, an administrator would need to crawl to the device to make a console connection to reconfigure the HiveAP.• If the location of a HiveAP is publicly accessible, someone could press the reset button on the front panel of the device to return the configuration to its default settings, log in using the default login name and password (admin, aerohive), and thereby gain complete admin access. (Note that you can disable the ability of the reset button to reset the configuration by entering this command: no reset-button reset-config-enable)A bootstrap configuration can help in both of these situations. For the first case, a bootstrap config with the necessary hive membership settings can allow the HiveAP to connect to the network and thereby become accessible over the network for further configuring. For the second case, a bootstrap config with a number of obstacles such as a hard-to-guess login name and password and a disabled access subinterface can make the firmware inaccessible and the device unusable.HiveAP-1 and -2 are in locations that are not completely secure. HiveAP-3 is a mesh point in a fairly inaccessible location. To counter theft of the first two HiveAPs and to avoid the nuisance of physically accessing the third HiveAP, you define a bootstrap config file that addresses both concerns and load it on the HiveAPs.
Chapter 11 Deployment Examples (CLI)180 AerohiveStep 1 Define the bootstrap config on HiveAP-11. Make a serial connection to the console port on HiveAP-1, log in, and load the default config.load config defaultrebootYou do not want the bootstrap config to contain any of your previously defined settings from the current config. Therefore, you load the default config, which has only default settings. When you begin with the default config and enter the commands that define the bootstrap config, the bootstrap config will have just those commands and the default config settings.2. Confirm the reboot command, and then, when you are asked if you want to use the Aerohive Initial Configuration Wizard, enter no.3. Log in using the default user name admin and password aerohive.4. Define admin login parameters for the bootstrap config that are difficult to guess.admin root-admin Cwb12o11siNIm8vhD2hs password 8wDamKC1Lo53Ku71You use the maximum number of alphanumeric characters for the login name (20 characters) and password (16 characters). By mixing uppercase and lowercase letters with numbers in strings that do not spell words or phrases, you make the login much harder to guess.5. Leave the various interfaces in their default up or down states. By default, the wifi0 and wifi0.1 interfaces are down, but the mgt0, eth0, wifi1, and wifi1.1 subinterfaces are up. The hive members need to use wifi1.1, which is in backhaul mode, so that HiveAP-3 can rejoin hive1 and, through hive1, access DHCP and DNS servers to regain network connectivity. (By default, mgt0 is a DHCP client.) You leave the eth0 interface up so that Hive-1 and Hive-2 can retain an open path to the wired network. However, with the two interfaces in access mode—wifi0 and wifi0.1— in the down state, none of the HiveAPs will be able provide network access to any wireless clients. Wireless clients cannot form associations through wifi1.1 nor can a computer attach through the eth0 interface—because it is also in backhaul mode—and obtain network access through the mesh.6. Define the hive settings so that any of the three HiveAPs using the bootstrap config can rejoin the grid.hive hive1hive hive1 password s1r70ckH07m3sinterface mgt0 hive hive1When a HiveAP boots up using the bootstrap config, it can rejoin hive1 because the configuration includes the hive name and password and binds the mgt0 interface to the hive. This is particularly useful for HiveAP-3 because it is a mesh point and can only access the wired network after it has joined the hive. It can then reach the wired network through either of the portals, HiveAP-1 or HiveAP-2.7. Save the configuration as a bootstrap config.save config running bootstrapIf anyone resets the current configuration, the HiveAP will load this bootstrap config and thwart any thief from accessing the configuration and any wireless client from accessing the network.Note: Be careful to remember the login name and password defined in a bootstrap config file. If they become lost or forgotten, you must obtain a one-time login key from Aerohive technical support. To get the key, you must already have had a support contract in place. The first one-time login key is free. After that, there is a small handling fee for each additional key.
Deployment Guide 181EXAMPLE 5: LOADING A BOOTSTRAP CONFIGURATIONStep 2 Save the bootstrap config to a TFTP server1. Check the configurations to make sure the settings are accurate.show config bootstrapCheck that the settings are those you entered in the previous step for the bootstrap config.show config backupNote that the backup config is the previous current config. This is the configuration that has all your previously defined settings.2. Return to the previous current config.load config backupreboot3. When HiveAP-1 finishes rebooting, log back in using the login parameters you set in "Example 1: Deploying a Single HiveAP" on page 162 (mwebster, 3fF8ha).4. Check that the current config is the same as your previous current config.show config current5. Save the file as bootstrap-hive1.txt to the root directory of your TFTP server running on your management system at 10.1.1.31, an address received by the same DHCP server and in the same subnet as the HiveAP addresses.save config bootstrap tftp://10.1.1.31:bootstrap-hive1.txtStep 3 Load the bootstrap config file on HiveAP-2 and HiveAP-31. Make a serial connection to the console port on HiveAP-2 and log in.2. Upload the bootstrap-hive1.txt config file from the TFTP server to HiveAP-2 as a bootstrap config.save config tftp://10.1.1.31:bootstrap-hive1.txt bootstrap3. Check that the uploaded config file is now the bootstrap config.show config bootstrap4. Repeat the procedure to load the bootstrap config on HiveAP-3.The bootstrap configs are now in place on all three HiveAPs.
Chapter 11 Deployment Examples (CLI)182 AerohiveCLI COMMANDS FOR EXAMPLESThis section includes all the CLI commands for configuring the HiveAPs in the previous examples. The CLI configurations are presented in their entirety (without explanations) as a convenient reference, and—if you are reading this guide as a PDF—as an easy way to copy and paste the commands. Simply copy the blocks of text for configuring the HiveAPs in each example and paste them at the command prompt.Commands for Example 1Enter the following commands to configure the SSID "employee" on the single HiveAP in "Deploying a Single HiveAP" on page 162:ssid employeessid employee security protocol-suite wpa-auto-psk ascii-key N38bu7Adr0n3interface wifi0.1 ssid employeesave configCommands for Example 2Enter the following commands to configure three HiveAPs as members of "hive1" in "Deploying a Hive" on page 165:HiveAP-1hive hive1hive hive1 password s1r70ckH07m3sinterface mgt0 hive hive1save configHiveAP-2ssid employeessid employee security protocol-suite wpa-auto-psk ascii-key N38bu7Adr0n3interface wifi0.1 ssid employeehive hive1hive hive1 password s1r70ckH07m3sinterface mgt0 hive hive1save configNote: The following sections omit optional commands, such as changing the login name and password, and commands used to check a configuration.
Deployment Guide 183EXAMPLE 5: CLI COMMANDS FOR EXAMPLESHiveAP-3ssid employeessid employee security protocol-suite wpa-auto-psk ascii-key N38bu7Adr0n3interface wifi0.1 ssid employeehive hive1hive hive1 password s1r70ckH07m3sinterface mgt0 hive hive1save configCommands for Example 3Enter the following commands to configure the hive members to support IEEE 802.1X authentication in "Using IEEE 802.1X Authentication" on page 170:HiveAP-1aaa radius-server first 10.1.1.10 shared-secret s3cr3741n4bl0Xssid employee security protocol-suite wpa-auto-8021xsave configHiveAP-2aaa radius-server first 10.1.1.10 shared-secret s3cr3741n4bl0X ssid employee security protocol-suite wpa-auto-8021xsave configHiveAP-3aaa radius-server 10.1.1.10 shared-secret s3cr3741n4bl0X ssid employee security protocol-suite wpa-auto-8021xsave config
Chapter 11 Deployment Examples (CLI)184 AerohiveCommands for Example 4Enter the following commands to configure the hive members to apply QoS (Quality of Service) to voice, streaming media, and data traffic in "Applying QoS" on page 173:HiveAP-1qos classifier-map oui 00:12:3b qos 6service mms tcp 1755service smtp tcp 25service pop3 tcp 110qos classifier-map service mms qos 5qos classifier-map service smtp qos 3qos classifier-map service pop3 qos 3qos classifier-profile employee-voice macqos classifier-profile employee-voice serviceqos classifier-profile eth0-voice macqos classifier-profile eth0-voice servicessid employee qos-classifier employee-voiceinterface eth0 qos-classifier eth0-voiceFor HiveAPs supporting IEEE 802.11a/b/gqos policy voice qos 5 wrr 20000 90qos policy voice qos 3 wrr 54000 60For HiveAPs supporting IEEE 802.11a/b/g/nqos policy voice qos 6 strict 512 0qos policy voice qos 5 wrr 20000 90qos policy voice qos 3 wrr 1000000 60user-profile employee-net qos-policy voice attribute 2save configHiveAP-2qos classifier-map oui 00:12:3b qos 6service mms tcp 1755service smtp tcp 25service pop3 tcp 110qos classifier-map service mms qos 5qos classifier-map service smtp qos 3qos classifier-map service pop3 qos 3qos classifier-profile employee-voice mac
Deployment Guide 185EXAMPLE 5: CLI COMMANDS FOR EXAMPLESqos classifier-profile employee-voice serviceqos classifier-profile eth0-voice macqos classifier-profile eth0-voice servicessid employee qos-classifier employee-voiceinterface eth0 qos-classifier eth0-voiceFor HiveAPs supporting IEEE 802.11a/b/gqos policy voice qos 5 wrr 20000 90qos policy voice qos 3 wrr 54000 60For HiveAPs supporting IEEE 802.11a/b/g/nqos policy voice qos 6 strict 512 0qos policy voice qos 5 wrr 20000 90qos policy voice qos 3 wrr 1000000 60user-profile employee-net qos-policy voice attribute 2save configHiveAP-3qos classifier-map oui 00:12:3b qos 6service mms tcp 1755service smtp tcp 25service pop3 tcp 110qos classifier-map service mms qos 5qos classifier-map service smtp qos 3qos classifier-map service pop3 qos 3qos classifier-profile employee-voice macqos classifier-profile employee-voice serviceqos classifier-profile eth0-voice macqos classifier-profile eth0-voice servicessid employee qos-classifier employee-voiceinterface eth0 qos-classifier eth0-voiceFor HiveAPs supporting IEEE 802.11a/b/gqos policy voice qos 5 wrr 20000 90qos policy voice qos 3 wrr 54000 60For HiveAPs supporting IEEE 802.11a/b/g/nqos policy voice qos 6 strict 512 0qos policy voice qos 5 wrr 20000 90qos policy voice qos 3 wrr 1000000 60user-profile employee-net qos-policy voice attribute 2save config
Chapter 11 Deployment Examples (CLI)186 AerohiveCommands for Example 5Enter the following commands to create bootstrap config files and load them on the hive members in "Loading a Bootstrap Configuration" on page 179:bootstrap-security.txtadmin root-admin Cwb12o11siNIm8vhD2hs password 8wDamKC1Lo53Ku71hive hive1hive hive1 password s1r70ckH07m3sinterface mgt0 hive hive1HiveAP-1save config tftp://10.1.1.31:bootstrap-security.txt bootstrapshow config bootstrapHiveAP-2save config tftp://10.1.1.31:bootstrap-security.txt bootstrapshow config bootstrapHiveAP-3save config tftp://10.1.1.31:bootstrap-meshpoint.txt bootstrapshow config bootstrap
Deployment Guide 189Appendix A Country CodesWhen the region code on a HiveAP is preset as "world", you must set a country code for the location where you intend to deploy the HiveAP. This code determines the radio channels and power settings that the HiveAP can use when deployed in that country. For HiveAPs intended for use in the United States, the region code is preset as "FCC"—for "Federal Communications Commission"—and the country code is preset for the United States. You can see the region code in the output of the show boot-param command.To set a country code when the region is "world", enter the following command, in which number is the appropriate country code number: boot-param country-code numberTo apply radio settings for the updated country code, reboot the HiveAP by entering the reboot command. To see a list of the available channels available for the country code that you have set on the HiveAP, enter the following command: show interface { wifi0 | wifi1 } channel. For example, the output for the show interface wifi0 channel command on a HiveAP whose region code is FCC and country code is 840 (United States) shows that channels 1 through 11 are available. If a channel does not appear in this list, you cannot configure the radio to use it.The following list of country codes is provided for your convenience.Countries and Country CodesAlbania 8Algeria 12Argentina 32Armenia 51Australia 36Austria 40Azerbaijan 31Bahrain 48Belarus 112Belgium 56Belize 84Bolivia 68Bosnia and Herzegovina 70Brazil 76Brunei Darussalam 96Bulgaria 100Canada 124Chile 152China (People’s Republic of China) 156Colombia 170Costa Rica 188Croatia 191Cyprus 196Czech Republic 203Denmark 208Dominican Republic 214Ecuador 218Egypt 818Note: Be sure to enter the correct country code. An incorrect entry might result in illegal radio operation and cause harmful interference to other systems.
Appenidix A Country Codes190 AerohiveEl Salvador 222Estonia 233Faeroe Islands 234Finland 246France 250France2 255Georgia 268Germany 276Greece 300Guatemala 320Honduras 340Hong Kong (S.A.R., P.R.C) 344Hungary 348Iceland 352India 356Indonesia 360Iran 364Iraq 368Ireland 372Israel 376Italy 380Jamaica 388Japan 392Japan1 (JP1) 393Japan2 (JP0) 394Japan3 (JP1-1) 395Japan4 (JE1) 396Japan5 (JE2) 397Japan6 (JP6) 399Japan7 (J7) 4007Japan8 (J8) 4008Japan9 (J9) 4009IJapan10 (J10) 4010Japan11 (J11) 4011Japan12 (J12) 4012Japan13 (J13) 4013Japan14 (J14) 4014Japan15 (J15) 4015Japan16 (J16) 4016Japan17 (J17) 4017Japan18 (J18) 4018Japan19 (J19) 4019Japan20 (J20) 4020Japan21 (J21) 4021Japan22 (J22) 4022Japan23 (J23) 4023Japan24 (J24) 4024Jordan 400Kazakhstan 398Kenya 404Korea (North Korea) 408Korea (South Korea, ROC) 410Korea (South Korea, ROC2) 411Korea (South Korea, ROC3) 412Kuwait 414Latvia 428Lebanon 422Libya 434Liechtenstein 438Lithuania 440Luxembourg 442Macau 446Macedonia (The Former Yugoslav Republic of Macedonia) 807Malaysia 458Malta 470Mexico 484Monaco (Principality of Monaco) 492Morocco 504Netherlands 528New Zealand 554Nicaragua 558
Deployment Guide 191Appenidix A Country CodesNorway 578Oman 512Pakistan (Islamic Republic of Pakistan) 586Panama 591Paraguay 600Peru 604Philippines (Republic of the Philippines) 608Poland 616Portugal 620Puerto Rico 630Qatar 634Romania 642Russia 643Saudi Arabia 682Singapore 702Slovakia (Slovak Republic) 703Slovenia 705South Africa 710Spain 724Sri Lanka 144Sweden 752Switzerland 756Syria 760Taiwan 158Thailand 764Trinidad y Tobago 780Tunisia 788Turkey 792U.A.E. 784Ukraine 804United Kingdom 826United States 840United States (Public Safety; FCC49) 842Uruguay 858Uzbekistan 860Venezuela 862Vietnam 704Yemen 887Zimbabwe 716
Appenidix A Country Codes192 Aerohive

Navigation menu