Aftershokz Trekz Titanium User Manual 1003428 ManualsLib Makes It Easy To Find Manuals Online!

User Manual: Aftershokz Aftershokz-Trekz-Titanium-User-Manual-1003428

Open the PDF directly: View PDF .
Page Count: 5

TREKZ TITANIUM

User Guide

Set up your Trekz Titanium

1. Charge 2. Pair 3. Connect

Let us take care of you!

Charge the headphones

with the included micro-USB

charging cable. The LED

indicator will turn blue when

charging is complete.

Press and hold the power

button for 5 seconds to

enter pairing mode. The LED

indicator will flash blue and red

repeatedly while in discovery.

Enable the Bluetooth®

settings on your device and

select “Trekz Titanium by

AfterShokz”. The LED indicator

will turn blue once connected.

We’ve got your back against damages.

Register your Trekz at bit.ly/RegisterMyTrekz

Multifunction Button

Micro-USB

Charging Port

Microphone 1

Microphone 2

Volume/Power Buttons

LED Indicator

A

B

Multifunction Button (A)

Volume Up/Power Button (B) Volume Down Button (C)

Play/pause music Click once One beep

Skip to next song Double-click while music is playing One beep

Answer/end call Click once One beep

Answer call waiting and put

the current caller on hold

Click once to switch between callers One beep

Answer call waiting and

hang up on current caller

Press and hold for 2 seconds One beep

Reject a call Press and hold for 2 seconds Two beeps

Voice dial Press and hold for 2 seconds “Voice dial”

Redial last number Double-click “Last number redial”

Function Action Prompt/”Audrey Says™”

Power on/off Press and hold the power button for

2 seconds

Four beeps and “Welcome

to Trekz Titanium”

Mute Press and hold both buttons for 2

seconds while on a call

“Mute on” or

“Mute off”

Change EQ setting Press and hold both buttons for 2

seconds while music is playing

“Equalization changed”

Check battery status Click the volume up or down button

while music is paused

“Battery high, medium, low

(or) charge me”

Adjust volume Click the volume up or down button

to adjust volume

One beep

Function Action Prompt/”Audrey Says™”

C

Part number AS600 Wireless range 33 ft (10m)

Speaker type Bone conduction transducer Battery Rechargeable lithium ion

Frequency response 20Hz~20KHz Continuous play 6 hours

Sensitivity 100 ± 3dB Standby time 10 days

Microphone -40dB ± 3dB Charge time 1.5 hours

Bluetooth® version Bluetooth® v4.1 Weight 1.27 oz (36g)

Compatible profiles A2DP, AVRCP, HSP, HFP Warranty 2 years

Specications

LED indicatorMuiltipoint pairing

1. Enter pairing mode

2. Press the multifunction button and volume up/power button

for 2 seconds (Audrey Says™ “Multipoint enabled”)

3. Pair rst device (Audrey Says™ “Connected”)

4. Shut down

5. Re-enter pairing mode

6. Pair second device (Audrey Says™ “Second device connected”)

7. Turn the device off, then power back on

Enter pairing mode, then press and hold the multifunction button, and both volume buttons simultaneously for 3 seconds.

How to reset your headphones

Solid red Charging

Solid blue Charging complete

Flashes red and blue Pairing mode

Flashes blue Incoming call

Flashes red every 2 minutes Low battery

We’re all ears! Got a question? Eager to share an experience?

Send us an email, or give us a call: support@aftershokz.com | +1-315-290-3855

To view this user guide in additional languages, visit bit.ly/TrekzUserGuide

• Store the headphones in a cool and dry place. The working temperature should be 0~45°C(32~113°F). Working in cold/hot environments or highly humid

areas may reduce the life of the battery.

• After storing the headphones for an extended period, charge the unit before using it again.

• The headphones are sweat resistant, but are NOT waterproof. DO NOT submerge the headphones in water.

• Listening with headphones at a high volume may affect your hearing and may distort the audio.

• When cleaning the headphones, use a soft dry cloth.

• Do not charge your headphones immediately after exercising, as any sweat or moisture inside the charging port could lead to a circuit burning.

Note:

Design and specications are subject to change without notice. For the most up-to-date product information, please visit www.aftershokz.com.

Storage and maintenance

Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC caution

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

This Class (B) digital apparatus complies with Canadian ICES-003.

Declaration of Conformity of Industry of Canada

FitBand (D)

Silicon rubber bands provide adjustability to accommodate smaller head sizes.

1. Slide FitBand (R) over the right transducer and along the right arm to rest over the charging port.

2. Slide FitBand (L) over the left transducer and along the left arm to align evenly with the right arm.

3. Rotate the FitBands around the arms until the desired t is achieved.

Earplugs (E)

Use with headphones in environments where it is safe to block out ambient noise, such as on an

airplane or train.

1. Roll earplugs rmly between ngers and place in ears.

2. To adjust EQ settings to reduce or enhance bass while wearing earplugs, press and hold volume

up and down buttons simultaneously.

Optional Accessories

D

E

#beopen

Visit us at aftershokz.com