Ai Thinker Technology ESP32-S WIFI module User Manual Ai Thinker Modules Specification

Shenzhen Ai-Thinker Technology co., LTD WIFI module Ai Thinker Modules Specification

Contents

User manual

   ESP32-S Wi-Fi+BT SoC Module V1.0   Copyright © 2017  Shenzhen Ai-Thinker Technology Co., Ltd All Rights Reserved                                           ESP32-S Wi-Fi+BT SoC Module Overview Esp32-S  has  a highly  competitive  package size and ultra-low power technology.  Esp32-S  can  be  widely  used  in  various  of  networking,  for  home  automation,  industrial wireless control, baby monitors,   sensing and other networking applications. Esp32-S  is  packaged  in  SMD,through  the standard  SMT  equipment  to  achieve  rapid production of products,to provide customers with High reliability of the connection,especially for Automation,  large-scale,  low-cost  modern production methods,It’s suitable for all kinds of Internet of things hardware terminal occasions.  - The smallest 802.11b/g/n Wi-Fi BT SoC Module  - Low power 32-bit CPU,can also serve the application processor - Up to 160MHz clock speed,Summary computing power up to 600 DMIPS - Overview built-in 520KB SRAM - Supports UART/SPI/I2C/PWM/ADC/DAC - SMD-38 package for easy welding - Support for OpenOCD debugging interface - Deep sleep current as low as 6.5μA - Embedded Lwip and FreeRTOS - Supports STA/AP/STA+AP operation mode - Support Smart Config/AirKiss technology - General AT commands can be used quickly - Support for serial port local and remote firmware upgrades (FOTA) Features  wireless  positiondevices, wireless positioning system signals
   ESP32-S Wi-Fi+BT SoC Module V1.0   Copyright © 2017  Shenzhen Ai-Thinker Technology Co., Ltd All Rights Reserved          Module Model  ESP32-S  Package  SMD-38 Size  18.0*25.8*2.8(±0.2)mm SPI Flash  Default 32Mbit Bluetooth  Bluetooth 4.2 BR/EDR and BLE standards Wi-Fi  802.11 b/g/n/e/i Interface   UART、SPI、SDIO、I2C、PWM、I2S、IR、ADC、DAC On-chip Sensor  Hall sensor, Temperature sensor, Capacitive touch sensor IO Port  22 UART Baudrate   Support 300~4608000bps,De115200 bps Frequency Range    2412 ~2462MHz for wifi/2402-2480 for bluetooth  Antenna  PCB Antenna     Transmit Power  802.11b: 20±2 dBm (@11Mbps)  802.11g: 24±2 dBm (@54Mbps)  802.11n: 24±2 dBm (@MCS7) Receiving Sensitivity CCK, 1 Mbps : -90dBm CCK, 11 Mbps: -85dBm 6 Mbps (1/2 BPSK): -88dBm 54 Mbps (3/4 64-QAM): -70dBm MCS7 (65 Mbps, 72.2 Mbps): -67dBm Power Dissipation  300mA@3.3V Security  WPA/WPA2/WPA2-Enterprise/WPS Power Supply Range  3.0V ~ 3.6V Operating Temperature  -20 ℃ ~ 85 ℃ Storage Environment  -40 ℃ ~ 90 ℃ , < 90%RH Weight  1.5g  Product Specifications Shenzhen Ai-Thinker Technology Co., Ltd Address: 7/F, Fengze Building B, Huafeng Industrial Park 2th, Hangkong street,Xixiang Raod, Baoan, Shenzhen China Website:www.ai-thinker.com    Tel:0755-29162996    E-mail:support@aithinker.com Contact US
FCC StatementThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the  module  is  installed must also  display  a  label referring to  the  enclosed  module. This exterior  label  can  use wording such  as  the following: “Contains Transmitter Module FCC ID:2AHMR-ESP32-S Or Contains FCC ID: 2AHMR-ESP32-S” when the module is installed inside another device, the user manual of this device must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate theequipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product Modular shall be used for fixed or mobile operations only. Minimum 20 cm must be maintained between device and user body during normal operations.The modular transmitter is only FCC authorized for FCC part 15 subpart C, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.

Navigation menu