Aiphone Lef 3L Users Manual Aiphone_e

LEF-3L Instructions LEF-3L_Instr_0109Y Instructions

LEF-3L-Instructions LEF-3L-Instructions

Aiphone Intercom System TD-6H/B LEF-3L Instr, 0109Y

LEF-3L to the manual 8b98c95a-e5d5-48c9-bd20-6cfc7fe08f4d

2015-02-05

: Aiphone Aiphone-Lef-3L-Users-Manual-355513 aiphone-lef-3l-users-manual-355513 aiphone pdf

Open the PDF directly: View PDF .
Page Count: 12

– 1 –

- SUPPLEMENT TO LEF INSTRUCTIONS -

The LEF-3L is a compact, wall or desk mount master station able to selectively release a door or call up a camera.

Used with any LE-(except LEF-3,5 and 10) or LS-series (North America only) remote station, communication can be

established with each station by selecting the channel on the master station. While the channel is selected, pressing

the door release button (left of TALK button) will release only the associated door. When used for camera call-up, a relay

closure will be maintained as long as a station is selected. The system can have up to four stations, in any combination of

masters or door stations (e.g. 2 masters and 2 doors). Master-to-master communication is also a standard feature.

(If communication between masters is not required, multiple LEF-3L's can be used to talk to 3 door stations.)

PRECAUTIONS

WARNING

(Negligence could result in death or serious injury.)

1. Do not dismantle or alter the unit. Fire or electric shock could result.

2. Do not connect any non-speciﬁ ed power source to the +, - terminals, and do not install two power supplies in

parallel to a single input. Fire, damage to the unit, or system malfunction could result.

3. Keep the unit away from water or any other liquid. Fire or electric shock could result.

4. When existing chime wires are used, it is possible that they contain AC voltage. Electric shock or unit damage

could result. Ask a qualiﬁ ed technician.

5. Do not use DC power supply with a voltage other than speciﬁ ed. Fire or electric shock could result.

CAUTION

(Negligence could result in injury or damage to property.)

1. Before turning on the power, make sure wires are not crossed or shorted. Fire or electric shock could result.

2. When mounting the unit on wall, install the unit in a convenient location, but not where it could be jarred or

bumped. Injury could result.

3. For DC powered systems, use Aiphone power supply model speciﬁ ed with system. If non-speciﬁ ed product is

used, ﬁ re or malfunction could result.

4. Do not install or make any wire terminations while power supply is plugged in. It can cause electrical shock or

damage to the unit.

5. In case of electrical storms, unplug the unit from AC outlet. If not, ﬁ re or electric shock could result.

6. Do not install the unit in any of the following locations. Fire, electric shock, or unit trouble could result.

* Places under direct sunlight, or near heating equipment that varies in temperature.

* Places subject to dust, oil, chemicals, hydrogen sulﬁ de (hot spring).

* Places subject to moisture and humidity extremes, such as bathroom, cellar, greenhouse, etc.

* Places where the temperature is quite low, such as inside a refrigerated area or in front of air-conditioner.

* Places subject to steam or smoke (near heating or cooking surfaces).

* Where noise generating devices such as dimmer switches, invertor electrical appliances, are closeby.

7. Do not install the unit in a location subject to constant vibration or impact. If dropped, injury or unit damage

could result.

GENERAL PRECAUTIONS

1. Keep the unit more than 1 m (3.3') away from Radio or TV set.

2. In areas where broadcasting station antennas are close by, the intercom system may be affected by radio

frequency interference.

3. The unit will be inoperative during a power outage.

4. This unit is for indoor use only. Do not use outdoors.

LEF-3L

3-Call Master Station with Selective Control Capability (Door Release or Camera Call-up)

Used with LE-D, LE-DA, LE-DL, LS-NVP/C Door Stations

P0015311A0109Y

General Prohibitions Prohibition on Subjecting the Unit to Water

Prohibition to Dismantle the Unit General Precautions

aiphone_e.indd 1 09.2.17, 2:13:51 PM

– 2 –

Wire Reference Chart (North America only)

Standard Communication

With selective door release and/

or camera call-up

Model # # of Conductors Wire # (22AWG) Wire # (18AWG) # of Conductors Wire # (22AWG)

LEF-3L 9 822210 x 12 822212

LE-A 3 822203 821803 x x

LE-D 3 822203 821803 x x

LE-DA 3 822203 821803 x x

１NAMES & FEATURES

FEATURES:

· Selective door release control

· CCTV camera call-up capability

· Single or multiple masters can be used in a system

· Intermixable, any number of masters and remotes up to 4 total stations

· Master to master communication in a multi-master system

· Single talkpath, with push-to-talk operation at master, and hands free communication at sub station

· Large variety of sub stations available

- Surface or ﬂ ush mount, with or without privacy (LE-A, LE-AN, LE-B, LE-BN)

- Weather resistant door stations (LE-D, LE-DA, LE-DL)

- Vandal proof sub stations (LE-SS, LE-SSR & LS-NVP/C)

· Subs call in with momentary tone and LED, remaining lit for approximately 20 seconds

· Selective calling to sub stations

· Selectively control external device from the master station in one of two ways with relay

- Momentary closure while “Door release ( )” button is pressed

- Maintained closure while station is selected

· Desk or wall mount

SOME APPLICATIONS:

Ofﬁ ces

Courthouses

Hotels/Motels

Retail/Convenience Stores

Small Secured Facilities

123

OFF

....

OCCUPIED

PRIV TALK

CALL

OFF OCCUPIED

VOL.VOICE

TALK

VOL.VOICE

LEF-3L

123

Microphone

Occupied LED

Door Release LED

ON LED

TALK Button

Speaker

Station Call-in LEDs

Station Selectors

OFF Button

(standby) Door Release ( ) Button

(The LEF-3L does not have the "Privacy feature")

Voice Volume Control

HighLow

aiphone_e.indd 2 09.2.17, 2:13:53 PM

– 3 –

2 SYSTEM OUTLINE & COMPONENTS

■ System outline

Individual Components for LEF-3L System:

* : North America only

*LS-NVP/C Vandal and weather resistant sub station, white powder coated (optional SBX-NVP surface box)

*LE-SS Stainless Steel 2-Gang sub station

*LE-SSR Stainless Steel 2-Gang sub station with red mushroom push button

*SBX-2G Surface mount box for LE-SS and LE-SSR

*LE-SS-1G Stainless Steel 1-Gang sub station (optional SBX-SS-1G surface box)

*SA-1 Surge Arrestor (1 per 2 wires being protected)

RY-PA Relay, 12V DC input, N/O dry closure output.

One required for each contact closure required off of each channel.

Can be momentary or maintained, according to wiring.

*RY-18L 12-18V DC “Form C” relay (N/O and N/C contacts)

PS-1225/UL/S 12V DC, 2.5A power supply, use for intercom only, 1 per system

PS-1215DIN 12V DC, 1.5A power supply, use for intercom only, 1 per system

LEF-3L TERMINAL DEFINITIONS:

＋ Positive 12V DC

− Negative

E Common communication

1∼3 Station number, communication to sub or other master

C "CALL", for receiving a call from another master station

R Occupied light control (0V DC when system is occupied)

COLOR-CODED WIRES:

White Common Door release activation (+12V DC when door release button is pressed)

Brown Ground when station 1 is pressed

Red Ground when station 2 is pressed

Orange Ground when station 3 is pressed

* North America only

LEF-3L

LE-D

(LE-D)

LE-D

Door Strike

LE-D

Door Strike

Door release button

RY-PA

PS-12

■ Package contents

• LEF-3L

• Packet of screws

• Installation &

Operation Manual

LEF-3L

3-call master with

selective door release

LE-D

Surface mount door station

LE-DL

Surface mount door station

(Aluminum)

LE-DA

Flush mount door

station with stainless

steel faceplate

LE-A

1-call sub station

LE-A3

3-call sub station

PT : AC Transformer

Door Strike

aiphone_e.indd 3 09.2.17, 2:13:55 PM

– 4 –

2 SYSTEM OUTLINE & COMPONENTS (Cont.)

LE-D/LE-DA TERMINAL DEFINITIONS:

１ Station number

Ｅ Common communication

− Negative

*LS-NVP/C TERMINAL DEFINITIONS:

Red Station number

Black Common communication

Green Negative

*LE-SS(R)/LE-SS-1G COLOR CODE:

Red Station number

Black

Common communication

Green Negative

* North America only

■ Precautions on Installation & Wiring

Before Installation:

· Make sure you have the proper power supply(ies) and all necessary and compatible equipment for the system.

· Lay out your system in advance, assigning station numbers for all sub station locations.

· Surge protection for the intercom equipment is recommended. Add SA-1 surge arrestors for the power supply, plus one

per two wires connected to the master station.

· Any other manufacturer's products installed with this system (power supply, external signaling device, etc.) are not

covered under Aiphone's warranty.

· When using a power supply that has no GROUND terminal, install a surge arrestor near the output as shown.

· Additional surge arrestors can be installed to protect communication lines. One surge arrestor per 2 wires on each

master station.

PS-1225/UL/S

PS-1215DIN

LEF-3L

DC 12V

Surge-

arrestor

Grounded

Install a surge-arrestor

at a location closest to the unit,

taken to earth ground.

aiphone_e.indd 4 09.2.17, 2:14:05 PM

– 5 –

Wire:

· Shielded wire is strongly recommended. Use the proper gauge for the distance being run.

· Wiring between masters must be a multi-conductor cable. If more than one cable is used to connect masters, the "E",

"C", and number terminal wires must be in the same jacketed cable. If necessary, run multiple "E" wires, one in each

cable.

Wiring Method:

· Run intercom cables at least 50cm (20") away from all AC wiring, ﬂ uorescent lights, dimmer switches, and other

electrical or electronic devices. Intercom wiring can cross AC wires at 90 degrees.

· Sub stations can be homerun to the nearest master station, or daisy-chained. If daisy-chained, include 2 common wires

plus 1 individual wire per station on the run.

· In a SINGLE MASTER SYSTEM ONLY: Subs can be wired with 2 conductors homerun. Jumpers between "E" and "-"

must be attached on all subs and at the master station.

Intercom Locations:

· Do not install intercoms near dimmer or light switches, or other electrical wall devices.

· To prevent feedback, do not place sub stations back-to-back on a common wall.

· Near alarm panels or other electronic equipment that may emit data noise.

· Behind a doorway or any other area that may block access to the unit.

■

Before actually installing the LEF system, Precautions on Installation & Wiring must be

thoroughly read and understood.

To access the inside of the unit for making wire connections:

1. Remove Operation plate & Directory card and loosen the screw on the front of the unit. (Do not remove

screw)

2. Carefully lift front of intercom up and off the back chassis.

3. If desired, unplug connectors and set unit aside during mounting and wiring of the back chassis.

4. When wiring is completed, plug in connectors and put unit back together. Peel protective covering off of Operation

plate.

Operation plate

PUSH

Directory card

To remove the operation

plate, push either left or

right side of the plate.

aiphone_e.indd 5 09.2.17, 2:14:07 PM

– 6 –

2 SYSTEM OUTLINE & COMPONENTS (Cont.)

■ Call tone adjustment

3-position volume switch, located under Operation plate.

Adjusts call tone volume to low (far left), medium, high (far right).

■ Selector switch for Call Tone in Occupied Mode

LEF surface mount master stations are set in the "B" position from

the factory. This allows a sub call-in tone to be heard at a muted

level while the master is in the occupied mode.

“A” position: Mutes call tone at master while system is in

occupied mode.

“B” position: Call tone is heard when master is in occupied

mode.

*No call tone between masters.

■ Cable requirements

Use multi-conductor cable with an overall shield, non-twisted, 22AWG to 18AWG (0.65mm to 1.0mm), to accommodate

the maximum number stations in the system.

Use the gauge speciﬁ ed for the maximum distance between the two farthest stations.

■ Power supply

The entire LEF system can be powered by one power supply (PS-1225UL/PS-1225S 12VDC 2.5A or PS-1215DIN

12VDC 1.5A), located near the center of the wire run.

For a system including the All Call and Chime with the BG-10C, one PS-1225UL(S) or PS-1215DIN will power the BG-

10C and the LEF system.

CALL

3-pos. call tone vol. switch

(under Operation plate)

LEF-3L

(FRONT CASE BACK VIEW)

(when shipped)

LEF-3L

aiphone_e.indd 6 09.2.17, 2:14:09 PM

– 7 –

3 MOUNTING

LEF-3L

intercom

SINGLE-GANG

BOX

83.5mm,

3-5/16"

2 screws

supplied

Chassis

Loosen

Operation

plate

Directory

card

★2

★1

83.5mm,

3-5/16"

SINFGLE-GANG BOX

Mounting

bracket

2 screws

supplied

（LE-A）

Unplug

while installing

OFF OCCUPIED

VOL.VOICE

TALK

AIPHONE

LEF-3L

123

Station-

selector (3)

Station

Call-in LEDs ON LED

Door release ( ) buttonOFF button

(standby)

Voice vol.

Control

Occupied LED

TALK button

Door release LED

Operation

plate

Back wiring LE room subs

Surface wiring or Desk-top use

★1, 2 : When running cable on the surface, pass cable through the top or bottom of the chassis and fasten with the wire clamps (attached,

one outside and one inside chassis). To pass the cable through the bottom side of the unit, cut out the cable inlet section.

OPERATION PANEL FOR LEF-3L

Cut out the cable inlet section

Desk-top use;

wall

Surface wiring

Bottom view of LEF-3L

Clamp

Cable

Back

view

aiphone_e.indd 7 09.2.17, 2:14:11 PM

– 8 –

4 WIRING DIAGRAMS - Most Common Applications

1 x LEF-3L, 3 x Door Stations

WIth Selective Door Release

2 x LEF-3L, 2 x Door Stations

With Master to Master communication shown on channel 3

With Selective Door Release

2 x LEF-3L, 1 x Door Station

With Master to Master Communication

Door Station wired on each station's own number terminal (different on each master)

IMPORTANT: When using selective outputs, a separate relay and power source

are required. Do not power external devices off of the system

power supply.

NOTE:

When running 2 conductors

homerun to each sub (single master

system only), leave jumper attached

between

—

on master and

door stations. Otherwise, remove

jumpers and use separate wires for

and

—

terminals.

AContact Rating: AC110V 1A

DC24V 1A

AContact Rating: AC110V 1A

DC24V 1A

Optional Remote station:

AContact Rating: AC110V 1A

DC24V 1A

To prevent shorts, be sure to cut unused lead wires at the button and insulate the ends.

–

Green

Black

Red

–

LEF-3L

PS-1225/UL/S

PS-1215DIN

12V DC

POWER

ONLY

LEF-3L

RY-PA

AC Transformer

–

LE-D/LE-DA LS-NVP

LE-SS

LEF-3L

Black Yellow

White

Brown

Red

Orange

White

Red

Brown

Orange

12V DC when "Door release ( )"

button is pressed

–

LEF-3L

PS-1225/UL/S

PS-1215DIN

12V DC

POWER

ONLY

–

Door #1

LE-D/LE-DA

–

Door #2

LE-D/LE-DA

Door #3

LE-D/LE-DA

–

RY-PA

for #1 RY-PA

for #2 RY-PA

for #3

Black

AC Transformer

Yellow

Black Yellow

White

Brown

Red

Orange

12V DC when "Door release ( )" button is pressed

Brown

Red

Orange

Brown

Red

Orange

–

LEF-3L

PS-1225/UL/S

PS-1215DIN

12V DC

POWER

ONLY

LEF-3L

Door #1

LE-D/LE-DA

Door #2

LE-D/LE-DA

RY-PA

for #2

Black

AC Transformer

Yellow

Black Yellow

RY-PA

for #1

E E

– –

–

White White

–

aiphone_e.indd 8 09.2.17, 2:14:13 PM

– 9 –

4 WIRING DIAGRAMS - Multiple Masters for Door Answering

LEF-3L System with External Signaling (RY-AC)

One door station with the ability to activate a separate doorbell

Shown with external signaling and door release relays

LEF-3L System with External Signaling (RY-AC)

Selective external signaling relay outputs for each door station call-in

IMPORTANT: When using selective outputs, a separate

relay and power source are required.

Do not power external devices off of the

system power supply.

To prevent shorts, be sure to cut unused lead wires at the button and insulate the ends.

AContact Rating: AC110V 1A

DC24V 1A

Contact Rating: 0.3A、240V AC

1.0A、24V DC

To prevent shorts, be sure to cut unused lead wires at the button and insulate the ends.

–

LEF-3L

PS-1225/UL/S

PS-1215DIN

12V DC

POWER

ONLY

LEF-3L

AC Transformer

LE-D/LE-DA

–

RY-PA

–

RY-AC

AC Transformer

External

Sounder

Black

Red

White

Yellow

White

Brown

Red

Orange

White

Brown

Red

Orange

–

LEF-3L

PS-1225/UL/S

PS-1215DIN

12V DC

POWER

ONLY

LEF-3L

LE-D/LE-DA

–

To External signaling

device & power

To External signaling

device & power

RY-AC

Red

Black

White

Yellow

Red

Black

White

Yellow

White

Brown

Red

Orange

White

Brown

Red

Orange

aiphone_e.indd 9 09.2.17, 2:14:16 PM

– 10 –

5 OPERATIONS & SPECIFICATIONS

OPERATIONS:

■ Calling a master or sub:

1. Depress a station selector button 1 ~ 3.

2. Press the TALK button to speak, and release to listen to the reply.

3. To conclude, depress OFF button.

■ Receiving a call from a sub station:

1. Sub station calls in with tone and LED, which stays lit for 20 seconds.

2. Depress the lit station selector button.

3. Press the TALK button to speak, and release to listen.

4. Communication at the door station is hands free.

5. Depress OFF button when ﬁ nished.

■ Receiving call from another master:

1. When a master calls to another master (without tone & LED), the responding master answers back handsfree.

2. The Occupied lamp will be on while the initiating master has a station selected.

3. Do not press any buttons on the master when responding to another master's call.

■

Door answering (from a master station only):

1. Audio door station calls in with an electronic call tone & LED, which stays lit for 20 seconds.

2. Depress the lit selector button, then press TALK to speak, release to listen.

■

Door release with “LOCK” button:

LEF-3L provides selective door release to multiple doors (One RY-PA for each door). When communication is

established to a door station, press the Door release ( ) button to release the corresponding door strike.

■

Camera Call-up feature:

If the "Camera Call-up" feature is included, the associated relay will provide a maintained closure as long as the station

is selected at the master.

NOTE:

The LEF-3L does not have the "privacy feature", and also cannot send a call tone to another master or remote station in the system.

SPECIFICATIONS:

Power Source: 12V DC at master. Use PS-1225, 1225UL, 1225S (2.5A) or PS-1215 DIN (1.5A). Do not use AC

power. Damage to the unit will result.

Current Consumption: 440mA

Communication Output: 800mW @ 20 ohms (receive); 500mW @ 20 ohms (transmit)

Communication: Push-to-talk, release-to-listen at master station (LEF-3L). Hands free at sub station.

Calling: Master to sub: By voice

Sub to master: Call tone and LED

Wiring: 2 common plus 1 individual per sub, looped; or 3 conductors homerun from each sub.

2 conductors homerun from each sub in a single-master system only.

Use Aiphone #822202 or #821802 ( 2 cond., 22 or 18AWG), or #822203 (3 cond. 22AWG)

12 conductors between master stations. Use Aiphone #822212. (North America only)

Shielded cable is strongly recommended.

aiphone_e.indd 10 09.2.17, 2:14:18 PM

– 11 –

WIRING DISTANCE:

Dimensions (HxWxD): 180H x 143W x 53.5D (mm). 7-1/16" x 5-5/8" x 2-1/8"

RY-PA Contact Rating: 1A, 110V AC or 24V DC

RESTRICTIONS

· Only one power supply can be used on one system.

· Up to 4 masters can be connected on the multiple masters conﬁ guration, or up to 3 masters on the intermix

conﬁ guration.

· Use the door release button only when the TALK button is not pressed. (Don't operate the door release when talking.)

Proper (relay) operation may not be guaranteed under the following conditions.

· When a master is called from another sub or master station while talking (Including when the Call tone is sounding)

· When a master is called from another master while the OCCUPIED lamp is on

6 TROUBLESHOOTING GUIDE

ENTRY # PROBLEM POSSIBLE CAUSE SOLUTION

１

Door station does not call

in (no call tone or LED

light).

Missing jumpers Are there 2 or 3 conductors run to the door station? If 2 wires, jumper must

remain attached between

and

—

at both the door station and the master

station. Replace jumper. In a multi-master system, the

—

jumper

should be removed and 3 wires should be connected.

Door station does not call

in (no call tone or LED

light) -- 3-wire connection.

Missing connection of

—

terminal.

If communication works, check connection between

—

terminal of door

station and master. Test call-in at master station by touching a jumper wire

between # and

—

terminal of master. If this rings the tone and lights the

light, the

—

wire from the door station is not connected properly.

Door station does not call

in (no call tone or LED

light) -- 3-wire connection.

Mis-wiring of

and

terminals.

Check that the

and

wire are not reversed. If they are, communication

will work but call-in will not.

No communication to

door station.

Mis-wiring of

terminal.

Communication is between the

and

terminal of the door station to a #

and

terminal of the master station. If call-in works, check the

wire for

continuity. Check the

and

wires at the sub to ensure that they are not

reversed.

–

M1 M2 PS M3

D1 D2

12V DC

POWER ONLY

12V DC

POWER ONLY

RY-PA

Figure 1

WIRING DISTANCE

Wire Distance

（MAX）

φ 1.0 ｍm（18AWG） 480 m（1575’） 240 ｍ（780’）

Figure 2

aiphone_e.indd 11 09.2.17, 2:14:22 PM

– 12 –

6 TROUBLESHOOTING GUIDE (Cont.)

ENTRY # PROBLEM POSSIBLE CAUSE SOLUTION

No master-to-master

communication.

terminals mis-wired

between masters.

Communication between masters is carried on the # wire of the calling

master to the

terminal of the receiving master. Verify that the

terminal

of the master that is being called is actually wired to the #terminal that is

being selected on the calling master.

LEF master has no

communication or tone, but

LED lights work.

Wrong power supply is

being used.

The LED lights will operate with a power source from 6VDC - 24VDC. The

ampliﬁ er in the LEF unit will only work when the system is supplied 12VDC.

Proper power supply is the PS-1225/UL/S, or PS-1215 DIN.

Feedback when the volume

control is turned up over

halfway.

—

jumpers attached

in a multi-master system.

Remove

—

jumpers on masters and door stations in the system,

provided there are 3 wires to the sub(s). If the sub only has 2 wires in a

multi-master system, the jumper must remain in place for the door call-in to

work. In this case, the side effect is the feedback problem when the audio

volume is turned up. The only alternative is to run the proper wire to the

door station(s) and remove all of the jumpers.

New installation has AC

buzz, noise, or hum in

system.

Too close to AC and/or

incorrect wire was used.

If the units are too close to an AC source such as AC wiring or dimmer

switches, move the intercom at least one stud space away from the AC

source. Other precautions include using shielded cable. If shielded wire was

used and there is still AC noise, tie all the shields together and ground to

an earth ground or negative on the power supply. If more than one jacketed

cable was used between masters, make sure the # terminals,

terminal,

and the

terminals are all in the same jacketed cable. If multiple cables

were used, include an

wire in each cable that carries a station number

wire in it.

Door release does not work.

Miswire or lack of RY-PA

relays.

Check the

WHITE

wire coming out of the PC board for voltage. When

depressing the Door release ( ) button, 12VDC is present across

WHITE

and

—

, which activates the relay. Ensure that the

BLACK

wires of the

RY-PA are connected to

WHITE

and either the

BROWN

RED

, or

ORANGE

wire for selective door release (which provides selective ground

when the corresponding channel is selected).

No call tone between

masters.

No Privacy feature on LEF-

3L.

Features not available

The LEF-3L unit does not have the PRIVACY feature or the ability to send

a call tone to another master station (as with the standard LEF-3). This

function is removed to allow the switch to be used for door release instead

of privacy.

Can't release the door from

the 2nd (additional masters) Wiring not connected

properly.

If door release works from the ﬁ rst master but not another(s), verify that

selective door release wires are connected between masters. (

WHITE

BROWN

RED

ORANGE

). RY-PA's are only required at one master.

External Signaling device

doesn't activate RY-AC mis-wired

Make sure that the WHITE wire of the RY-AC is connected to the #

terminal that is to be activating the relay, and that

RED

and

BLACK

are

connected to

and

—

, respectively.

WARRANTY

Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of one year after

delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which examination shall

disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the ﬁ nal decision whether there is a defect in

materials and/or workmanship; and whether or not the product is within the warranty.

This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of instructions

furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover batteries or damage

caused by batteries used in connection with the product.

This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone. Aiphone will not be

responsible for any costs incurred involving on site service calls.

AIPHONE CO., LTD., NAGOYA, JAPAN

AIPHONE CORPORATION, BELLEVUE, WA, USA

AIPHONE S.A.S., LISSES-EVRY, FRANCE

http://www.aiphone.com/

Printed in Japan (E)

aiphone_e.indd 12 09.2.17, 2:14:25 PM

Aiphone Lef 3L Users Manual Aiphone_e

LEF-3L Instructions LEF-3L_Instr_0109Y Instructions

LEF-3L-Instructions LEF-3L-Instructions

Aiphone Intercom System TD-6H/B LEF-3L Instr, 0109Y

LEF-3L to the manual 8b98c95a-e5d5-48c9-bd20-6cfc7fe08f4d

Navigation menu

Versions of this User Manual:

Views

Navigation