Air Oasis Induct 9 Users Manual

9 to the manual e07342af-2fb4-4b1b-af46-77cf38c8d4f2

: Air-Oasis Air-Oasis-Induct-9-Users-Manual-505779 air-oasis-induct-9-users-manual-505779 air-oasis pdf

Open the PDF directly: View PDF .
Page Count: 6

Download
Open PDF In Browser	View PDF

Troubleshooting Guide
Problem

Reason

Unit does not turn on.

1. Power Cord

2. AHPCO™ Cell

3. Indicator Light Not
Working

Solution
1. Check to make sure
power cord is plugged
in or properly connected to HVAC unit.
2. Check to make
sure UV lamp within
AHPCO™
Cell
in
plugged in completely.
3. Make sure exposed
end of black fiber optic
cord is exposed to the
UV light.

Induct 9
Owner’s
Manual

This Manual Includes:

• Warranty
• Safety Warnings
• Installation Instructions
• Operating Instructions
• Replacement Directions
• Troubleshooting Tips

3401 Airway Blvd
Amarillo, TX 79118
Toll-Free: 1-800-936-1764 Fax: 1-806-373-7799
www.AirOasis.com
Copyright© 2006 Air Oasis All Rights Reserved

Before operating this unit or replacing the AHPCO™
Cell carefully read the contents of this manual.

Introduction
The air you breathe is filled with thousands of particles of air pollution. Some of the
pollutants like dust and lint are large enough to be visible to the naked eye, but pollutants such as pollen, smoke, germs, bacteria, etc., are microscopic in size. Your
Air Oasis™ Induct ACT™ air purifier has been designed to destroy these invisible
pollutants and provide your home or place of work with the luxury of clean air.
The AHPCO™ Cell is designed to help eliminate sick building syndrome risks by
reducing airborne microbes, contaminants, VOCs and odors, with our advanced
AHPCO process. The AHPCO Cell is contained within the Induct ACT™ unit. When
the Earth Care system is in operation the AHPCO Cell uses an Advanced Hydrated
Photocatalytic Oxidation process to reduce airborne contaminants.
Why use Hydrated Photocatalytic Oxidation?
Germicidal UV light rays have been used for decades by the medical industry as
a method for destroying micro-organisms (germs, viruses, bacteria). Germicidal
UV light is effective in reducing airborne micro-organisms that pass through the
light rays. However, germicidal UV light has little to no effect on gases, vapors or
odors.
Ozone, on the other hand, is very effective on gases, vapors, VOCs and odors.
However, too much ozone can be a health hazard, and traditional methods of
producing ozone (i.e. corona discharge) have maintenance problems and create
nitric acid and nitric oxides which can cause damage to the respiratory system.
The combination of ozone (O3) and UV light, in the presence of our patent-pending quad-nano Xtreme™ catalyst, creates the Advanced Oxidation reaction. This
advanced reaction chamber creates ozone gas and destroys it within the same
chamber by converting it to friendly oxidizers. This oxidation further attacks the
micro-organisms as well as significantly reducing odors and VOCs. By engineering
the proper light wavelengths in the dual function AHPCO Cell, we have effectively
designed a system that will not exceed the recommended Federal Safety Limits
for ozone (.04 ppm) in an occupied room, while still providing reductions in odors
and microbials.
With the Earth Care AHPCO Cell, many gases and odors are abated, microorganism reductions can be as much as 99%, and the room will have safe, low
ozone levels no greater than forest air, (.01 - .02 ppm) or air after a thunderstorm,
which gives the room fresh, clean odor-free air.

Step 3
Remove three (3) wing-nuts securing the AHPCO Cell in place. Then
slide the AHPCO Cell up and out of
the unit.
CAUTION
UV lamp may be hot and could
cause serious burns if not handled
properly. Please wait until AHPCO
Cell has cooled to room temperature to remove from unit.
AHPCO™ Cell contains Hg (Mercury) and should be disposed of
according to disposal laws. Find
disposal centers at www.earth911.
org.

Step 4
Reverse steps 1-3 to set new AHPCO Cell in place. Be sure to place the
exposed tip of the fiber optic cord between the first rings of the new AHPCO
Cell and in close proximity to the UV lamp. This will ensure the indicator
light functions properly.

Replacement Date Reminder
The AHPCO™ Cell should be replaced every three years.
3 Years Date:			
6 Years Date:			
9 Years Date:			
Hg lamp contains mercury. Manage in accord with disposal laws.
Find disposal centers at www.earth911.org.

1

6

Induct 9 Installation Instructions

Step 1
	
Tear out the
cutout template and
trace the rectangle
onto the ductwork.

Step 2
	
Drill holes at
each corner of the
rectangle. trace the
rectangle onto the
ductwork.

If you do not have a hole saw tear this page off and cut the
circle out. Then place on the ductwork in desired position
and trace the rectangle. Drill holes as indicated and then
use a jig saw or metal cutting snips to cut out the circle.

Step 3
	
Insert unit into
pre-cut hole.

Cut Out
Step 4
	
Drill the metal
tapping screws in to
hold unit in place.

Step 4
Plug the power cord into an electrical outlet. You may optionally have an
electrician wire the air purifier to your HVAC unit so that the air purifier only
operates when your HVAC fan is running. Once the unit is plugged in the
indicator light should glow to indicate the AHPCO Cell is working properly.

Read all instructions carefully before operating
your air purifier.
Table of Contents
Introduction

1

Safety Instructions and Cautions

2

Warranty

3

Maintenance and Customer Service

4

Installation and Operation

4-5

Replacement Parts

5-6

Troubleshooting Guide

7

Important Safety Instructions
When operating electrical appliances, basic precautions should always be followed.

AHPCO™ Cell Replacement
Step 1
CAUTION: Before attempting to service the Air Oasis unit, be sure the
power is off and unplugged.

Remove three (3) screws at the top of
the aluminum face plate. Then slide
the face plate up and off.

Step 2
Unplug the four pin lamp connectors and fiber optic cords from the
AHPCO Cell.

WARNING To reduce the risk of fire, electric shock or injury:
• Do not use outdoors or on wet surfaces.
• Use only as described in this manual.
• Do not use with damaged cord or plug. If appliance is not working as it should,
has been dropped, damaged, left outdoors, or dropped into water, call customer
service at 1-800-936-1764.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings.
• Unplug from power source before performing any maintenance or removing
front cover.
• It’s strongly recommended that only a licensed electrician or HVAC installer
properly install this unit.

CAUTION
AHPCO™ Cell contains Hg (Mercury) and should be disposed of according to
disposal laws. Find disposal centers at www.earth911.org.
If the UV lamp is broken do not touch the cell or glass with your hands.
UV lamp may be hot and could cause serious burns if not handled properly. Please
wait until the AHPCO Cell has cooled to room temperature to remove from unit.

5

2

Warranty

Maintenance and Customer Service

Air Oasis gives you the following limited warranty for this product only if it was originally purchased for residential or commercial use but, not resale from Air Oasis or
an Air Oasis Authorized Retail Dealer.

If you require any additional information or have problems with your Air Oasis appliance, you may call Air Oasis customer service at:
1-800-936-1764

Air Oasis will repair or replace, free of charge, to the original purchaser, any part
that is found to be defective in material or workmanship within three (3) years of
the date of purchase.

Please have your serial and model numbers, found on bottom of the unit, handy
when calling.

This limited warranty covers the replacement of a defective AHPCO Cell for a period of three years.
This limited warranty does not apply to any part subjected to accident, abuse, certain commercial uses, alteration, misuse, damage caused by act of God, the use
of voltages other than indicated on the label displayed on this product or service of
this product by anyone other than Air Oasis.
Air Oasis does not authorize any person or representative to assume or grant any
other warranty obligation with the sale of this product.
Air Oasis’ limited warranty is valid only if you retain proof of purchase from Air Oasis or an Air Oasis Authorized Retail Dealer for this product. If you purchase this
product from any other source, your purchase is “AS IS”, which means Air Oasis
grants you no warranty, and that you, not Air Oasis, assume the entire risk of the
quality and performance of this product, including the entire cost of any necessary
servicing or repairs of any defects.
Air Oasis’ liability for damages to you for any costs whatsoever arising out of this
statement of limited warranty shall be limited to the amount paid for this product
at the time of original purchase, and Air Oasis shall not be liable for any direct,
indirect, consequential or incidental damages arising out of the use or inability to
use this product.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD, AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL
APPLY AFTER THIS PERIOD.
Some states do not allow limitations on the duration of implied warranties, so
the above limitation may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
To obtain warranty service and return authorization number, contact us at:
PH: (800) 936-1764, FAX: (806) 373-7799 or E-mail to feedback@airoasis.com
NOTE: All returned packages that do not have an RMA# will be refused.
3

Save your sales receipt to show if your Air Oasis appliance should ever need any
warranty service.

Installation and Operation
It’s strongly recommended that only a licensed electrician
or HVAC installer properly install this unit.
The purifiers can be installed on either the return or supply side of the
plenum.

Step 1
Cut a 2” hole in the plenum using a hole
saw. Make sure the hole is centered so
that no part of the mounting plate is hanging off the edges of the plenum when the
probe is inserted.

Step 2
Insert the probe into the 2” hole until the
back mounting plate is flush against the
plenum surface. We recommend mounting
the unit with the rectangular side facing either left or right, but not down or up.

Step 3
Attach the mounting plate to the plenum
surface using sheet metal screws. There
are predrilled holes on the mounting plate
that can be used as a guide. It’s recommended to seal the edges of the mounting
plate using aluminum insulation tape.
4



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c006 1.236519, Wed Jun 14 2006 08:31:24
Create Date                     : 2007:11:01 15:41:32-05:00
Modify Date                     : 2007:11:01 15:41:35-05:00
Metadata Date                   : 2007:11:01 15:41:35-05:00
Creator Tool                    : Adobe InDesign CS3 (5.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 9481 bytes, use -b option to extract)
Version ID                      : 1
Instance ID                     : uuid:050c047d-ec51-4fcb-a0b5-b3b02ca69bac
Document ID                     : adobe:docid:indd:9a07e405-8733-11dc-8dc4-d90d989677e0
Rendition Class                 : proof:pdf
Derived From Instance ID        : 111c5c55-83cf-11dc-a539-e861cc7f4f8a
Derived From Document ID        : adobe:docid:indd:c4ee4956-2729-11db-878a-bc4e9bb3ecd8
Derived From Version ID         : 1
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:67B8A0118F88DC119CB5D01E82C1E168, uuid:63B8A0118F88DC119CB5D01E82C1E168, uuid:36A8582F8F88DC119CB5D01E82C1E168, uuid:A25380359888DC119CB5D01E82C1E168, uuid:CB92D2319888DC119CB5D01E82C1E168, uuid:1CBD2BB69788DC119CB5D01E82C1E168, uuid:C792D2319888DC119CB5D01E82C1E168, uuid:A02104D08E88DC119CB5D01E82C1E168, uuid:5FB8A0118F88DC119CB5D01E82C1E168, uuid:A42104D08E88DC119CB5D01E82C1E168
Manifest Reference Document ID  : uuid:66B8A0118F88DC119CB5D01E82C1E168, uuid:62B8A0118F88DC119CB5D01E82C1E168, uuid:35A8582F8F88DC119CB5D01E82C1E168, uuid:CE92D2319888DC119CB5D01E82C1E168, uuid:CA92D2319888DC119CB5D01E82C1E168, uuid:1BBD2BB69788DC119CB5D01E82C1E168, uuid:C692D2319888DC119CB5D01E82C1E168, uuid:9F2104D08E88DC119CB5D01E82C1E168, uuid:5EB8A0118F88DC119CB5D01E82C1E168, uuid:A32104D08E88DC119CB5D01E82C1E168
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 6
Creator                         : Adobe InDesign CS3 (5.0)

EXIF Metadata provided by EXIF.tools