AirTies Wireless Networks AIR49200 2 Port Gigabit Ethernet 11ac/11n Wireless Router User Manual

AirTies Wireless Networks 2 Port Gigabit Ethernet 11ac/11n Wireless Router Users Manual

Contents

Users Manual

INTERNETYOUR MODEMYOUR STB12123412SUCCESSOUT OF RANGE
Designed by AirTies in Europe. Manufactured in China.Wi-Fi Name: AirTies_Air4920_XXXXWi-Fi Password: abcdef1234Designed by AirTies in Europe. Manufactured in China.Wi-Fi Name: AirTies_Air4920_XXXXWi-Fi Password: abcdef1234INTERNETYOUR MODEM YOUR STB1WPS2WPSYOUR STBADDITIONAL UNIT
SUCCESSSUCCESSSUCCESS
INTERNETYOUR MODEM
LED Indicators: Condition LED Color LED Behavior Timing State Identifier Explanation Recommended Action(s)Power OFF (OFF/Dark) - APower on device if desired. No other action required.Power ON White Solid (No blinking) BNo action required. If unit was just powered on, then please wait for at least 2 minutes for the unit to complete its boot process.Firmware upgrade in progress White Blinking500ms OFF500ms ON CNo action required. Please wait for the unit to reboot (and enter state B).WLAN is active and the node has an active strong Mesh/Repeater connection on the 5GHz Radio. Green Blinking50ms OFF5000ms ON DNo action required.WLAN is active and all MESH/Repeater links on 5GHz Radio are weak. Red Solid (No blinking) EBring device closer to another device on the MESH.WLAN is active or Searching for radar activity (OFF/Dark) Both Radio LEDs are dark FNo action required.WPS is in progress Green Blinking in sync with 2.4GHz ledWPSCert. Compliant GNo action required.WPS is succesful Green Solid (No blinking)WPSCert. Compliant HThis behavior is temporary and lasts for about 10 seconds, after which the LEDs go to one of the following states:1) MESH with strong signal (state D), and2) MESH with poor signal (state E)If LED is red (state E) then bring device closer to another device on the MESH. If LED is green (state D), then no action is required.Unconfigured device. Green Blinking in sync with 2.4GHz led4000ms OFF4000ms ON IDevice has factory setting and is not connected to the home network in any way (e.g., the device is not wired to the router-gateway)Configure device (refer to Quick Installation Guide)WLAN active, Device configured, No Repeater/MESH link on 5GHz Radio. Green Solid (No blinking) JFirst AP (wired to router-gateway) No action required.There is configured MESH/Repeater connection on 5GHz, however connection is inactive. (Cannot connect.) Red Blinking1000msec OFF1000msec ON KAP is part of MESH, but unable to find any of its MESH partners.Make sure other device(s) that are part of the MESH network are powered on and close enough to connect.WPS is not successful Red Blinking with 2.4GHz ledWPSCert. Compliant LThis behavior is temporary and lasts for about 10 seconds, after which the LEDs go back to the state the device was in before the WPS attemptOn failure, repeat WPS attempt after bringing device next to another device that is already on the MESH network (i.e., in state D).Power5 GHz
This product makes use of software developed by the open source community. Any such software is licensed under the specific license terms applicable to that particular software (like GPL, LGPL etc). Detailed information on the applicable licenses and license terms can be found on the device's user interface. By using this product, you acknowledge that you have reviewed such license terms and that you agree to be bound by them. Where such terms entitle you to the source code of said software, that source code will be made available at cost upon request from AirTies. To obtain a copy of said source code, please send your request in writing via email to osrb@airties.com or via snail mail to: AirTies Wireless Communications Gulbahar Mah. Avni Dilligil Sok. No:5Celik Is Merkezi, Mecidiyeköy, 34394ISTANBUL/TurkeyAirTies will mail to you a CD with the requested source code for $9,99 plus the cost of shipping. For details please contact osrb@airties.com

Navigation menu