Airtech Information and Communication ATS-400B FM HANDHELD TRANCEIVER User Manual CONTENTS

Download:
Mirror Download [FCC.gov]
Document ID	370967
Application ID	wFVcBMdttD+1bRoL+KcW1w==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	41.88kB (523554 bits)
Date Submitted	2003-11-05 00:00:00
Date Available	2003-11-04 00:00:00
Creation Date	2003-09-02 14:43:17
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2003-09-02 14:43:33
Document Title	CONTENTS
Document Creator	Wordìš© Acrobat PDFMaker 5.0
Document Author:	J. N. Lee

APPROVAL
1. FCC Approval
FCC ID: ONKATS-400B
1) Safety Training Information
Your
FM
Handheld
Transceiver
generates
RF
electromagnetic energy during transmit mode. This radio is
designed for and classified as “Controlled Exposure /
Occupation Environment”, meaning it must be used only
during the course of employment by individuals aware of the
hazards, and the ways to minimize such hazards. This radio
is NOT intended for use by the “General Population /
Uncontrolled Environment.
This radio complies with FCC RF radiation exposure limits
set forth for a controlled environment. This radio should be
installed and operated with a minimum distance of 2.5
centimeters between the radio and your body. Therefore, to
ensure that your exposure to RF electromagnetic energy is
within the FCC allowable limits for occupational use, always
follow below information.
Do not operate the radio without a proper antenna as this
may damage the radio and may also cause you to exceed
FCC RF exposure limits. A proper antenna is the antenna
supplied with this radio by the manufacturer or an antenna
specifically authorized by the manufacturer for use with this
radio.
Do not transmit for more than 50% of total radio use time
(“50% duty cycle”). Transmitting more than 50% of the time
can cause FCC RF exposure compliance requirements to be
exceeded.
Always use Airtech supplied accessories (antennas, batteries,
belt clips, speaker/mics, etc.).
Use of unauthorized
accessories can cause the FCC RF exposure compliance
requirements to be exceeded.
Always keep the antenna at least 2.5 cm (1 inch) away from
the body when transmitting and only
3 use the belt-clips, when
attaching the radio to your belt, etc., to ensure FCC RF
exposure compliance requirements are not exceeded.
2) LABEL
This radio complies with the FCC
RF exposure limits for Occupational
Use Only.
3) This device complies with the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority
to operate the equipment.
CONTENTS
General Features
1.
GENERAL FEATURES.................................................2
UNPACKING.................................................................3
OPTIONAL ACCESSORIES.........................................3
GETTING READY.........................................................2
DESCRIPTION..............................................................3
OPERATION .................................................................4
CHARGER AND BATTERY..........................................5
Ultra compact design & size
(102(W)x50(H)x36(D), 310g with high capable battery)
2. Heavy duty durable construction
3. 256 channels
4. 38 CTCSS/ 83 CDCSS/ 83 INVERR CDCSS
5. PC Programmable, transferable by cloning
6. Time-out timer (TOT)
7. Busy Lockout (BCLO)
8. Battery saving mode
9. Low battery alert
10. DTMF ANI
11. Transmit output power High/Low
12. DC 7.5V Ni-Mh battery
Installation: Align the belt clip with the plastic slots of
the battery pack. Slide the belt clip onto the battery pack,
pushing firmly until a click heard.
Removal: Hold up the belt clip release tab with a
fingernail or a coin (or like instrument). While holding up
the release tab, slide the belt clip out and away from the
battery pack.
Unpacking
Unpack and check that all items have been enclosed.
Packing contents: ⑥radio ②antenna ③battery pack
(1,700 mAH) ④belt clip ⑤hand strap ⑥charger ⑦user’s
2.
3.
Installation and Removal, Battery Pack
Installation: Turn off the transceiver. Hold the
transceiver with the back of the unit
facing up. Place the battery pack against
the back of the transceiver so that the
tabs on the transceiver engage the four
openings in the battery pack. Slide the
battery pack toward the top of the
transceiver until a click heard.
Removal: Turn off the transceiver. Hold the radio with
the back of the unit facing up. With the thumbnail of your
other hand slide the latch lever down. While holding the
latch lever down, slide the battery pack down toward the
bottom of the transceiver. Separate the battery pack from
the transceiver.
Installation Antenna
Rotate the antenna clockwise until it is seated firmly.
*. Before starting operation, make sure the battery is fully
charged.
manual
Optional
Accessories External speaker/microphone
1. Additional battery pack
Getting Ready
1.
Installation and Removal, Belt Clip
Description
ⓐ Power on / off and Volume Control Switch
Turn the transceiver on by rotating power on / off and volume
control switch clockwise and control the volume.
ⓑ External Earphone/MIC and Programming Jack Socket
ⓒ Whip Antenna.
ⓓ Tx / Rx Indicate LED (3 colors)
On
Transmitting
Red
Blinking Low battery
Green
On
Receiving, monitoring
Blinking Different sub-tone when receiving
Initializing, programming and
Orange
On
cloning
ⓔ Speaker
ⓕ Function
ⓖ Squelch (SQ)
ⓗ Channel Up Button
ⓘ
ⓙ Emergency Key
ⓚ Tx Output H/L
ⓛ Channel Down Button
ⓜ PTT(Push To Talk) Button
ⓝ Monitor Button
Press to monitor. Holding down over 2 seconds keeps monitoring
function on, and press shortly again or PTT Button to stop
Hold down to transmit, release to receive. Channel Select Button
4
Select the desired channel with pressing Up and Down button,
pressing and holding down more than 1 second makes the channel
moving fast. And you can choose On or Off in function mode
Operation
1. Power on / off and Volume Control:
Rotate the Power on/off and Volume Control Switch ⓐ
clockwise to turn power on, then the LED lights orange
and power–up tone is generated after about on second,
indicating the transceiver has passed the self–diagnostic.
When you turn on the transceiver, it comes same
channel and function with your last using. Rotate this
switch ⓐ clockwise to increase the volume or
counter-clockwise to reduce the volume. Rotate it ⓐ
counter-clockwise fully to turn power off.
2. Channel Selection:
Press up/down button, to desired channel.
3. Transmit:
Hold down the PTT Button ⓜ and talk into the MIC at
1-2 in distance. The LED lights red on transmitting.
Release the PTT button ⓜ to receive.
4. Receive:
Choose the desired channel by press up/down button ⓗ
ⓛ. The LED lights green on receiving. In case the signal
doesn’t match the sub–tone the green LED will blink.
5. Monitor:
Press to monitor. Pressing the monitor button for more
than 2 seconds will cause continuous monitor condition.
To release the monitor mode, press and release the
monitor button quickly.
6. Scan
1). Press and hold the function button and up
button to start scan.
a. Scan type will be priority type, else normal type
If the radio is programmed in priority channel,
scan.
b. If priority type scan, the scan has stopped on a
non-priority channel there will be skips in the
audio while the radio checks the priority
channel. During priority scanning you may talk
c. on the last busy channel by pressing the
function button and up button. After completing
the conversation, restart scan.
d. To delete a busy channel from scan, press
down button. If the up button is pressed, the
scan will restart but stop again if the channel
continues to be busy.
7. Transmit operation during scan
①. If the radio is programmed in ptt channel at
scanning is home channel: TX will occur on the
channel the scan started.
②. If the radio is programmed in ptt channel at
scanning is last busy channel: TX will occur on the last
busy channel
8. TX ANI
If the radio was initially programmed for this feature
pressing the PTT will cause a DTMF code to be send
that can identify the sending radio.
9. 2/5 Tone Decode (Selcall)
During initial radio programming by the technician this radio
can be configured for several different types of decode
operation. If a channel is selected that has Selcall
activated the radio will be muted until the proper signal is
received. When this occurs the radio can sound a ringing
type alert signal or a voice message maybe heard.
Depending upon the initial programming, pressing the
PTT may cause an automatic identifier to be sent. When
programmed for Selcall pressing the monitor and function
buttons at the same time can cause the Selcall mode to
be cancelled and generate an automatic identification.
Please have your radio technician or dispatcher fully
explain this operation.
Charger and Battery
1. Battery (Ni-Mh)
Voltage
Duty time (5-5-90)
2. Charger
Input power
Operating temperature
DC 7.5V
Over 10 hrs
(90~250VAC)
10-30 deg. C
Connect the charger to an appropriate outlet (90~250 VAC).
Turn the transceiver power off and place the radio into the
front socket of the charger. The red light illuminates during
charging and the green light comes on when the charge is
complete. When you place two batteries in the charger at the
same time, the front battery will charge first. The rear battery
will begin charging when the front battery charge is complete.
On
Charging
Red
Blinking
Abnormal battery
Green
On
Fully charged
Orange On
Stand-by for charging (rear cup)
Blinking
Discharging
When you put a battery in the rear cup of the charger the
charger checks the voltage. If voltage is over 7.4V, the
charger starts discharging for 4 minutes then checks
again. If voltage is still more than 7V, it discharges until
the voltage is 6V then starts charging.
User’s Manual
Land Mobile Radio (LMR)
Model: ATS-400B

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2003:09:02 14:43:33+09:00
Create Date                     : 2003:09:02 14:43:17+09:00
Page Count                      : 7
Creation Date                   : 2003:09:02 05:43:17Z
Mod Date                        : 2003:09:02 05:43:17Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : J. N. Lee
Metadata Date                   : 2003:09:02 05:43:17Z
Creator                         : J. N. Lee
Title                           : CONTENTS
Page Mode                       : UseNone
Tagged PDF                      : Yes

EXIF Metadata provided by EXIF.tools