Aiwa Csd Td310 Users Manual

CSD-TD310 CSDTD310

CSD-TD320 to the manual 15ae3833-f082-421f-8de6-fa8e82e49a67

: Aiwa Aiwa-Csd-Td310-Users-Manual-360796 aiwa-csd-td310-users-manual-360796 aiwa pdf

Open the PDF directly: View PDF .
Page Count: 10

CSD-TD310

CSD-TD320

8A-CHB-933-01

010405ACK-I-AIS

COMPACT DISC STEREO RADIO CASSETTE RECORDER

English : See page 2. En

Español : Ver la página 10. E

Français : Voir page 18. F

U

OPERATING INSTRUCTIONS

INSTRUCCIONES DE MANEJO

MODE D’EMPLOI

2 ENGLISH

Precautions

Read the Operating Instructions carefully and

completely before operating the unit. Be sure to keep

the Operating Instructions for future reference. All

warnings and cautions in the Operating Instructions and

on the unit should be strictly followed, as well as the

safety suggestions below.

Installation

1 Water and moisture - Do not use this unit near

water, such as near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, swimming pool,

or the like.

2 Heat - Do not use this unit near sources of heat,

including heating vents, stoves, or other appliances

that generate heat.

It also should not be placed in temperatures less

than 5°C (41°F) or greater than 35°C (95°F).

3 Mounting surface - Place the unit on a flat, even

surface.

4 Ventilation - The unit should be situated with

adequate space around it so that proper heat

ventilation is assured.

Allow 10 cm (4 in.) clearance from the rear and the

top of the unit and 5 cm (2 in.) from each side.

- Do not place the unit on a bed, rug, or similar

surface that may block the ventilation openings.

- Do not install the unit in a bookcase, cabinet, or

airtight rack where ventilation may be impeded.

5 Objects and liquid entry - Take care that objects or

liquids do not get inside the unit through the

ventilation openings.

6 Carts and stands - When placed or

mounted on a stand or cart, the unit

should be moved with care.

Quick stops, excessive force, and

uneven surfaces may cause the unit

or cart to overturn or fall.

7 Condensation - Moisture may form on the CD

pickup lens when:

- The unit is moved from a cold spot to a warm spot

- The heating system has just been turned on

- The unit is used in a very humid room

- The unit is cooled by an air conditioner

When this unit has condensation inside, it may not

function normally. Should this occur, leave the unit

for a few hours, then try to operate again.

8 Wall or ceiling mounting - The unit should not be

mounted on a wall or ceiling, unless specified in the

Operating Instructions.

Electric Power

1 Power sources - Use on batteries or AC house

current, as specified in the Operating Instructions

and marked on the unit.

2 Polarization - As a safety feature, some units are

equipped with polarized AC power plugs which can

only be inserted one way into a power outlet. If it is

difficult or impossible to insert the AC power plug

into an outlet, turn the plug over and try again. If it

still does not easily insert into the outlet, please call

a qualified service technician to service or replace

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

Explanation of Graphical Symbols:

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended

to alert the user to the presence of

uninsulated “dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert the

user to the presence of important

operating and maintenance (servicing)

instructions in the literature accompanying

the appliance.

OWNER’S RECORD

For your convenience, record the model number (you

will find it at the bottom of the unit) and serial number

(you will find it in the battery compartment) in the space

provided below. Please refer to them when you contact

your AIWA dealer in case of difficulty.

Model No.

Serial No.

“CAUTION:TO REDUCE THE RISK OF

ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.”

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ENGLISH 3

Power supply

The OPE/BATT indicator lights up while the power is

on.

Using on AC house current

Connect the AC cord as illustrated below.

CAUTION

Use only the supplied AC cord. Use with other cords

may result in the risk of fire.

Using on batteries

Open the lid of the battery compartment on the rear and

insert eight R14 (size C) batteries, not supplied, with

the 0 and 9 marks correctly aligned. Then close the

lid.

To switch from AC power supply to battery power

supply, disconnect the AC cord from the AC inlet.

When to replace the batteries

The OPE/BATT indicator becomes dim, the tape speed

slows down, volume decreases, or sound is distorted

during operation.

Notes on batteries

• Do not mix different types of batteries or old batteries

with new ones.

• When the unit is not to be used for a long period,

remove the batteries to prevent needless battery

wear.

• Never recharge the batteries, apply heat to them or

take them apart.

• Remove dead batteries.

If liquid leaks from the batteries, wipe thoroughly to

remove.

En

to the AC inlet of the unit

to an AC outlet

(AC 120 V, 60 Hz)

supplied AC cord

the outlet. To avoid defeating the safety feature of

the polarized plug, do not force it into a power outlet.

3 AC power cord

- When disconnecting the AC power cord, pull it out

by the AC power plug. Do not pull the cord itself.

- Never handle the AC power plug with wet hands,

as this could result in fire or shock.

- Power cords should be firmly secured to avoid

being bent, pinched, or walked upon. Pay

particular attention to the cord from the unit to the

power socket.

- Avoid overloading AC outlets and extension cords

beyond their capacity, as this could result in fire or

shock.

4 Extension cord - To help prevent electric shock, do

not use a polarized AC power plug with an extension

cord, receptacle, or other outlet unless the polarized

plug can be completely inserted to prevent exposure

of the blades of the plug.

5 When not in use - Unplug the AC power cord from

the AC outlet or remove all the batteries if the unit

will not be used for several months or more. When

the cord is plugged in, a small amount of current

continues to flow to the unit, even when the power is

turned off.

Maintenance

Clean the unit only as recommended in the Operating

Instructions.

Damage Requiring Service

Have the units serviced by a qualified service

technician if:

- The AC power cord or plug has been damaged

- Foreign objects or liquid have got inside the unit

- The unit has been exposed to rain or water

- The unit does not seem to operate normally

- The unit exhibits a marked change in performance

- The unit has been dropped, or the cabinet has been

damaged

DO NOT ATTEMPT TO SERVICE THE UNIT

YOURSELF.

OPE/BATT

R14 (C)

RADIO/BAND,

POWER

6STANDBY

A

\

SKIP/SEARCH

TUNE

+

-

REPEAT

FM MODE

/OSC

SLEEP

PLAY/PAUSE/

PRESET

STOP/

MEMORY

4 ENGLISH

1Press RADIO/BAND repeatedly to select

the desired band.

FM AM

The power is turned on and the previously tuned

station is received.

2Press r, t (TUNE -, +) to select a

station.

During FM stereo reception, is displayed.

After listening, press POWER 6STANDBY to turn

the power off.

For better reception

For quick tuning (Auto Search)

Keep r, t pressed until the tuner starts

searching for a station. When a station is tuned to, the

search stops.

If the broadcast signal is weak, it does not stop. To

stop the search manually, press r or t.

TUNER OPERATION

A

FM MODE/OSC

- If an FM stereo broadcast contains noise, press the

button so that is displayed.

Noise is reduced, although reception is monaural.

To restore stereo reception, press the button again.

- If a high-pitched sound is heard during AM recording,

press the button repeatedly until the noise is reduced.

Its position can be checked by “•” being on or off the

display.

To change the AM tuning interval

The default setting of the AM tuning interval is 10 kHz/

step. If you use this unit in an area where the frequency

allocation system is 9 kHz/step, change the interval as

follows.

1Press RADIO/BAND to display FM.

2Press s while pressing RADIO/BAND to display the

AM frequency.

When the AM tuning interval is changed, the preset

stations are cleared.

NOTE

If the unit picks up noise from other electrical

appliances nearby, like a TV or fluorescent lights, move

the unit away.

To listen with the headphones

Connect headphones with a stereo mini plug to the \

jack.

Extend the rod antenna

and orient it for the best

reception.

The antenna is inside the

unit. Position the unit for

the best reception.

AMFM

ENGLISH 5

En

PRESETTING STATIONS

You can preset up to 15 stations in each band.

1Select a station.

2Press s STOP/MEMORY once so that “M”

is displayed to store the station.

A station is assigned a preset number, beginning

from 1 in consecutive order for each band.

3Repeat steps 1 and 2.

The next station will not be stored if a total of 15

preset stations have already been stored for a

band.

To listen to preset stations

Select a band then press e PLAY/PAUSE/PRESET

repeatedly.

To clear a preset station

Select the preset number first. Within 4 seconds, keep

s pressed until “M” and the preset number disappear

in the display.

The higher numbers in the band are decreased by one.

Preset number

Frequency

Maintenance

To clean the cabinet

Use a soft cloth lightly moistened with mild

detergent solution. Do not use strong solvents

such as alcohol, benzine or thinner.

To clean the heads

When the tape heads are dirty;

- high frequency sound is not emitted

- the sound is not adequately high

- the sound is off-balance

- the tape cannot be erased

- the tape cannot be recorded on

After every 10 hours of use, clean the tape heads

with a head cleaning cassette.

Use separately sold dry-type or wet-type cleaning

cassette.

Refer to the instructions of the cleaning cassette

for details.

To clean the lens

Use a cotton swab slightly

moistened with cleaning

fluid. Wipe gently from the

center to the edge.

Lens

CD,

POWER

6STANDBY

B

SKIP/SEARCH

TUNE

+

-

REPEAT

FM MODE

/OSC

SLEEP

PLAY/PAUSE/

PRESET

STOP/

MEMORY

6 ENGLISH

1Press CD.

The power is turned on.

2Press CD OPEN to open the disc

compartment. Place a disc with the

printed side up and close the disc

compartment.

Total number of tracks and total playing time are

displayed. It will take about 15 seconds when

loading a CD-RW disc.

3Press e PLAY/PAUSE/PRESET to

start play.

The number of the track being played and elapsed

playing time are displayed.

s STOP/MEMORY – Stops play.

e PLAY/PAUSE/PRESET – Pauses play. To

resume play, press again.

r,t SKIP/SEARCH – Searches for a particular

point during playback. Keep r or t pressed

and then release it.

– Skips to the beginning of a track. Press r or

t repeatedly.

REPEAT – Repeats a single track or all tracks. Select

as follows.

[

1 : A single track is played repeatedly. Select a

track with r or t.

[

: All tracks are played repeatedly.

CD OPERATION

B

To start play when the power is off, press CD. The

power is turned on and play of the loaded disc begins

(Direct Play Function).

After listening, press POWER 6STANDBY to turn the

power off.

NOTE

• Do not use irregular shape CDs (example: heart-

shaped, octagonal ones).

It may result in malfunctions.

• Do not place more than one disc in the disc

compartment.

• Do not try to open the disc compartment during play.

• Do not touch the lens. Doing so may cause

malfunctions.

• The unit may not play a CD-R/RW disc that is

recorded on personal computers or some kinds of

CD-R/RW recorders because of differences in

recording platforms.

• Do not attach any seal or label to either side (the

recordable side or the labeled side) of a CD-R/RW

disc. It may cause malfunction.

• Do not load an unrecorded CD-R/RW disc. It will take

over 30 seconds to read the disc. The disc may be

damaged if you try to open the disc compartment

while reading the disc.

CD OPEN

ENGLISH 7

En

PROGRAMMED PLAY

Up to 30 tracks can be programmed from the disc.

1In stop mode, keep s STOP/MEMORY

pressed until “M” flashes in the display.

2Press r, t to select a track, then

press s STOP/MEMORY to store it.

3Repeat step 2 to program other tracks.

4Keep s STOP/MEMORY pressed until

“M” stops flashing to finish the program.

“M” remains displayed and indicates the unit stores

the programmed tracks.

5Press e to start play.

To check the program, press r or t in stop

mode.

To clear the program, press s once in stop mode so

that “M” disappears in the display.

To change the programmed tracks, clear the

program and repeat all the steps again.

Track number

Programmed number

Specifications

Tuner section

Frequency range, antenna — FM: 87.5 - 108.0 MHz

Rod antenna, AM: 530/531 - 1,710/1,602 kHz (10/9 kHz

step) Ferrite bar antenna

Deck section

Track format — 4 tracks, 2 channels / Frequency range

— Normal tape: 50 - 12,500 Hz (EIAJ) / Recording

system — AC bias / Erasing system — Magnet erase /

Heads — Recording/playback head (1), Erasure head

(1)

CD player section

Disc — Compact disc / Scanning method — Non-

contact optical scanner (semiconductor laser)

General

Speaker — 80 mm cone type (2) / Output —

Headphones jack (stereo mini-jack) / Power output —

2.5 W + 2.5 W (EIAJ 7 ohms, T.H.D. 10% DC) / Power

requirements — DC 12 V using eight size C (R14)

batteries, AC 120 V, 60 Hz / Power consumption —

18 W / Dimensions (W × H × D) — 310 × 171 × 260 mm

(121/4 × 63/4 × 101/4 in.) / Weight (excluding batteries)

— 2.8 kg (6 lbs. 3 oz.) / Accessory — AC cord (1)

Specifications and external appearance are subject to

change without notice.

COPYRIGHT

Please check the copyright laws relating to

recordings from disc, radio or external tape for the

country in which the machine is being used.

If an erroneous display or malfunction occurs

Make sure that none of the deck operation buttons is

pressed.

Press s while pressing POWER 6STANDBY.

If the unit cannot be reset in the way above, disconnect

the AC cord and remove all the batteries to turn off the

display.

Leave the unit for a while and turn the power back on.

r, t

QSOUND

3-MODE EQUALIZER

POWER6STANDBY

VOLUME

C

PAUSE

STOP/EJECT

FF REW PLAY REC

Use Type I (normal) tapes only.

INSERTING A TAPE

Press Z STOP/EJECT to open the cassette

holder and insert a tape with the exposed side

up and the side to be played facing out.

Push the cassette holder to close.

PLAYING A TAPE

Press x PLAY while the power is off.

The power is turned on and play of the inserted tape

begins.

The volume level is displayed during tape operation.

Z STOP/EJECT – Stops play. The power will be

automatically turned off.

a PAUSE – Pauses play. To resume play, press

again.

f FF/ g REW – Fast forwards/ rewinds. To stop

the winding, press Z.

TAPE OPERATION

C

8 ENGLISH

RECORDING

Note that recording is done on only one side of the

tape.

1Insert a tape with the side to be recorded

facing out.

2Get ready to record from the source.

To record from a CD, press CD and load the disc.

To record from a radio broadcast, press RADIO/

BAND and tune to a station.

3Press w REC to start recording.

x PLAY is pressed simultaneously.

When the selected function is CD, CD play and

recording starts simultaneously.

To record only the selected tracks of a CD

1Follow steps 1 to 4 of PROGRAMMED PLAY on

page 7 to program tracks.

2Press w REC.

To stop recording, press Z STOP/EJECT. To stop

CD play, press s STOP/MEMORY.

To pause recording, press a PAUSE. To resume

recording, press again.

To erase recording, press w REC while the power is

off.

After recording, press POWER 6STANDBY to turn the

power off.

To prevent accidental erasure

Break off the plastic tabs on the cassette tape with a

screwdriver or other pointed tool after recording.

To record on the tape again

Cover the tab openings with adhesive tape, etc.

Tab for side A

Side A

SETTING THE SLEEP TIMER

The unit can be turned off automatically at a specified

time.

1Keep pressed until “30” flashes in

the display.

2Within 4 seconds, press r or t to

specify the time until the power is turned

off.

Each time it is pressed, the time changes between

10 and 90 minutes in 10-minute steps.

To check the time remaining until the power is

turned off

Repeat step 1 shown above. The remaining time is

displayed for 4 seconds.

To cancel the sleep timer

Display the remaining time and press r or t

repeatedly until OFF is displayed.

NOTE

If the unit is turned off during tape playback, x on the

deck will not be released. Press Z to release x.

ENGLISH 9

En

SOUND ADJUSTMENT

Volume or tone adjustment does not affect recording.

VOLUME

Press VOLUME N or M. The volume level is

displayed as a number from 0 to MAX (25).

• The volume level is automatically set to 14 if the

power is turned off when the volume level is set to

15 or more. (except when turning the power back

on within 4 seconds)

3-MODE EQUALIZER

Press 3-MODE EQUALIZER repeatedly until the

desired mode is displayed.

The equalizer mode changes to R (Rock), P (Pop),

J (Jazz) or no equalization, cyclically.

Rock - Emphasizes the high and low range of music.

Pop - Emphasizes voice and midrange of music.

Jazz - Emphasizes the low range of music.

QSOUND system

This system provides a rich, three dimensional sound

area for stereo sources.

You can enjoy more enhanced sound.

Press QSOUND and the QSOUND indicator lights up.

• At higher volumes, turning QSOUND on may cause

sound distortion. In this case, make the volume

down.

Specified time While the sleep timer works,

the dot keeps flashing.

GENERAL

NOTE

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

... Reorient or relocate the receiving antenna.

... Increase the separation between the equipment and

receiver.

... Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

... Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

Modifications or adjustments to this product, which are

not expressly approved by the manufacturer, may void

the user’s right or authority to operate this product.

Printed in Indonesia