Alarm Controls 1200S 600S Installation Instructions

User Manual: Alarm Controls 600S Installation Instructions Installation Instructions

Open the PDF directly: View PDF .
Page Count: 6

SOLID DOOR

ALARM CONTROLS CORPORATION

19 BRANDYWINE DRIVE P.O. BOX 280

DEER PARK, NY 11729

800 645-5538 WWW.ALARMCONTROLS.COM

MAGNETIC LOCK INSTALLATION INSTRUCTIONS

ALARM CONTROLS CORPORATION OFFERS A COMPLETE LINE OF MAGNETIC LOCKS AND ACCESSORY ITEMS

TO ASSIST THE INSTALLER IN MANAGING EVERY APPLICATION.

THE MAGNETIC LOCK IS DESIGNED TO MOUNT TO THE DOOR FRAME ON THE STOP SIDE OF THE DOOR IN A

TYPICAL OUTSWINGING DOOR INSTALLATION,(SEE PAGE 2 FOR INSWINGING DOOR INSTALLATION).

SUFFICIENT HEADER SPACE MUST BE AVAILABLE TO MOUNT THE MAGNETIC LOCK TO INSURE A SAFE AND

SECURE INSTALLATION.

1. NOTE TYPE OF DOOR FRAME HEADER AND INSTALL FILLER PLATE OR ANGLE BRACKET AS REQUIRED TO

PROVIDE A FLAT MOUNTING SURFACE ON THE DOOR HEADER THE ENTIRE LENGTH OF THE MAGNETIC LOCK.

HEADER HEADER HEADER

OUT

SWINGING

DOOR

OUT

SWINGING

DOOR

OUT

SWINGING

DOOR

MAGNET MAGNET

FILLER

PLATE

MAGNET

ARMATURE

PLATE

ARMATURE

PLATE

ARMATURE

PLATE

ANGLE

BRACKET

HEADER

PLATE

2. FOLD TEMPLATE ON DOTTED LINE TO FORM A 90 DEGREE ANGLE. TAPE TEMPLATE AGAINST DOOR HEADER

WITH DOOR IN A CLOSED POSITION 1” FROM DOOR FRAME OPPOSITE HINGE SIDE OF DOOR JAMB.

FOR A PAIR OF DOUBLE DOORS PLACE TEMPLATE AT THE CENTER OF THE DOOR OPENING.

TRANSFER HOLE LOCATIONS TO DOOR AND FRAME HEADER, (SEE TEMPLATE INSTRUCTIONS).

3. FOLLOW TEMPLATE INSTRUCTIONS FOR HOLE SIZES. USE THE ILLUSTRATIONS BELOW TO DETERMINE THE

PROPER HOLE PREPARATION FOR THE ARMATURE PLATE ACCCORDING TO THE DOOR TYPE IN THE

INSTALLATION.

THE INCLUDED HARDWARE PACKAGE CONTAINS ALL NECESSARY ITEMS TO COMPLETE THE INSTALLATION.

HOLLOW DOOR

STEP 2

FOLLOW WITH

1/2” DIA. HOLE

THRU DOOR

STEP 1

DRILL 1/4” DIA.

HOLE THRU

ARMATURE

SIDE OF DOOR

STEP 2

DRILL 1/2” DIA.

HOLE THRU SEX

BOLT SIDE

OF DOOR

ONE THICKNESS

ONLY

STEP 1

DRILL 21/32” DIA.

HOLE THRU

ARMATURE

SIDE OF DOOR

ONE THICKNESS

ONLY

OUTSWINGING DOOR INSTALLATION

ARMATURE

PLATE MUST

ROCK ON DOOR

ARMATURE

PLATE MUST

ROCK ON DOOR

PLEASE READ BEFORE INSTALLATION

TO REMOVE THE HEADER PLATE INSERT HEX KEY INTO HOLES LOCATED AT

THE BOTTOM OF LOCK ON THE RIGHT AND LEFT SIDE AND UN-SCREW THE CAP SCREWS

INSWINGING DOOR INSTALLATION WITH L- Z BRACKET

STEP 1

FASTEN THE L BRACKET ON THE DOOR FRAME IN A SUITABLE LOCATION.

MOUNT THE MAGNETIC LOCK TO THE L BRACKET.

MAKE SURE THAT THE MAGNETIC LOCK DOES NOT OBSTRUCT THE

CLOSING OF THE DOOR.

CONNECT THE CORRECT VOLTAGE TO THE MAGNET.

STEP 2

ASSEMBLE THE Z BRACKET WITH THE SOCKET HEAD CAP SCREWS

PROVIDED. DO NOT TIGHTEN THE CAP SCREWS AT THIS TIME. THE

Z BRACKET MUST BE ADJUSTABLE.

STEP 3

MOUNT THE ARMATURE PLATE TO THE ADJUSTABLE SECTION OF THE Z

BRACKET WITH THE ARMATURE BOLT. DO NOT REMOVE THE RUBBER

WASHER ATTACHED TO THE ARMATURE BOLT.

USE ONE RUBBER WASHER BETWEEN TWO METAL WASHERS ON THE

ARMATURE BOLT. THE WASHER ASSEMBLY MUST BE BETWEEN THE

ARMATURE PLATE AND THE ADJUSTABLE SECTION OF THE Z BRACKET.

APPLY THE SCREW LOCKING AGENT TO THE ARMATURE BOLT.

DO NOT OVER TIGHTEN. ARMATURE MUST ROCK TO ALIGN WITH THE MAGNET.

STEP 4

CLOSE THE DOOR AND ALIGN THE ARMATURE PLATE TO THE MAGNET

AND APPLY POWER TO THE MAGNET. LET THE ARMATURE PLATE BOND

TO THE MAGNET. BE SURE THE Z BRACKET ASSEMBLY IS FIRMLY

AGAINST THE CLOSED DOOR.

TIGHTEN THE CAP SCREWS HOLDING THE Z BRACKET ARMATURE PLATE

ASSEMBLY.

FASTEN THE Z BRACKET ASSEMBLY TO THE DOOR WITH THE SCREWS SUPPLIED.

STEP 5

CHECK THE COMPLETED ALIGNMENT AND INSTALLATION OF THE

MAGNET AND ARMATURE PLATE BY OPENING AND CLOSING THE DOOR

BY ENERGIZING AND DE-ENERGIZING THE MAGNETIC LOCK SEVERAL

TIMES.

THIS WILL INSURE THAT THE CORRECT OPERATION AND ALIGNMENT

OF THE MAGNETIC LOCK HAS BEEN PROPERLY INSTALLED.

DOOR

FRAME

L

BRACKET

RUBBER

WASHER

ARMATURE

BOLT

ADJUSTABLE

Z BRACKET

Z BRACKET

ARMATURE

ASSEMBLY

ADJUSTABLE

SECTION OF

Z BRACKET WITH

ARMATURE PLATE

ATTACHED

COMPLETED

INSWINGING DOOR

INSTALLATION

MAGNETIC LOCK L / Z BRACKETS FOR INSWINGING DOORS

MAGNETIC LOCK CARE AND MAINTENANCE

TYPICAL MAGNETIC LOCK WIRING

MAGNETIC LOCK ELECTRICAL SPECIFICATIONS

AM2370 FOR 300 POUND MAGNETIC LOCK

AM3370 FOR ALL 600 POUND MODELS OF SINGLE MAGNETIC LOCKS

AM6370 FOR ALL 1200 POUND MODELS OF SINGLE MAGNETIC LOCKS

AM3375 FOR ALL 600 POUND MODELS OF DOUBLE MAGNETIC LOCKS

AM6375 FOR ALL 1200 POUND MODELS OF DOUBLE MAGNETIC LOCKS

MAGNETIC LOCKS HAVE NO INTERNAL MOVING PARTS AND REQUIRE A MINIMUM AMOUNT OF MAINTENANCE.

IT IS RECOMMENDED THAT THE FACE OF THE ARMATURE PLATE AND MAGNET BE WIPED CLEAN AND A L IGHT

COATING OF A SUITABLE SILCONE LUBRICANT BE APPLIED TO EACH SURFACE TO PREVENT RUST ALTHOUGH

THE MATING SURFACES HAVE BEEN PLATED. THIS ONLY NEEDS TO BE DONE WHEN DIRT BUILD-UP IS NOTICED.

THE ARMATURE PLATE BOLT AND THE HEX HEAD SCREWS HOLDING THE MAGNET TO HEADER PLATE SHOULD

BE CHECKED EVERY THREE MONTHS TO INSURE A SAFE AND SECURE INSTALLATION.

300 POUND MODEL SINGLE MAGNETIC LOCK, 250 MA. @ 12 VDC, 130 MA. @ 24 VDC

ALL 600 POUND MODELS OF SINGLE MAGNETIC LOCK, 400 MA. @ 12 VDC, 200 MA. @ 24 VDC

ALL 1200 POUND MODELS OF SINGLE MAGNETIC LOCK, 400 MA. @ 12 VDC, 200 MA. @ 24 VDC

ALL 600 POUND MODELS OF DOUBLE MAGNETIC LOCKS, 400 MA. @ 12 VDC, 200 MA. @ 24 VDC, EACH LOCK

ALL 1200 POUND MODELS OF DOUBLE MAGNETIC LOCKS, 400 MA. @ 12 VDC, 200 MA. @ 24 VDC, EACH LOCK

ALL MAGNETIC LOCKS ARE SET AT THE FACTORY FOR 24 VDC

FILTERED

DC

POWER

SUPPLY

N/C

REX

BUTTON

DIGITAL

KEYPAD

MAGNETIC

LOCK

NEGATIVE

POSITIVE

+

-

PIR

WIRE GAUGE CHART

TROUBLE SHOOTING GUIDE

50

FEET

100

FEET

150

FEET

200

FEET

300

FEET

400

FEET

500

FEET

750

FEET

1000

FEET

200 MA.

300 MA.

400 MA.

600 MA.

800 MA.

1 AMP.

DISTANCE FROM POWER SUPPLY TO MAGNETIC LOCK

D

C

C

U

R

R

E

N

T

24 GA.

24 GA.

22 GA.

22 GA.

22 GA.

20 GA.

22 GA.

22 GA.

22 GA.

20 GA.

18 GA.

18 GA.

22 GA.

22 GA.

20 GA.

18 GA.

18 GA.

16 GA.

22 GA.

20 GA.

18 GA.

18 GA.

16 GA.

14 GA.

20 GA.

18 GA.

18 GA.

16 GA.

14 GA.

14 GA.

18 GA.

18 GA.

16 GA.

14 GA.

12 GA.

12 GA.

18 GA.

16 GA.

14 GA.

14 GA.

10 GA.

10 GA.

16 GA.

14 GA.

14 GA.

12 GA.

10 GA.

14 GA.

14 GA.

12 GA.

10 GA.

8 GA.

8 GA.10 GA.

12 VDC

24 VDC

22 GA.

22 GA.

22 GA.

20 GA.

24 GA.

22 GA.

22 GA.

22 GA.

20 GA.

20 GA.

22 GA.

22 GA.

22 GA.

20 GA.

18 GA.

18 GA.

22 GA.

22 GA.

20 GA.

18 GA.

18 GA.

16 GA.

22 GA.

20 GA.

18 GA.

18 GA.

16 GA.

14 GA.

20 GA.

20 GA.

18 GA.

16 GA.

14 GA.

20 GA.

18 GA.

16 GA.

14 GA.

14 GA.

14 GA.

18 GA.

16 GA.

14 GA.

14 GA.

12 GA.

10 GA.

12 GA.

24 GA.

24 GA.

22 GA.

22 GA.

24 GA.

24 GA.

24 GA.

24 GA.

PROBLEM CAUSE SOLUTION

LOCK BUZZES

INSUFFICIENT HOLDING FORCE

DOOR DOES NOT LOCK

DOOR STATUS SENSOR NOT WORKING

(APPLICABLE MODELS)

AC VOLTAGE CONNECTED TO LOCK

AC RIPPLE IN POWER SUPPLY

INCORRECT INPUT VOLTAGE

LOW INPUT VOLTAGE

MISALIGNMENT OF ARMATURE PLATE

ARMATURE PLATE SCREWED TIGHT

TO DOOR

WRONG HARDWARE ASSEMBLY

NO POWER TO DOOR

MAGNET IN ARMATURE PLATE

NOT ALIGNED WITH LOCK

SUPPLY DC VOLTAGE TO LOCK

REPLACE POWER SUPPLY

CHECK VOLTAGE JUMPER POSITION

FOR CORRECT VOLTAGE SETTING

LOCK SET AT FACTORY FOR 24 VDC

CHECK POWER SUPPLY VOLTAGE

WIRE GAUGE INCORRECT FOR WIRE RUN

ARMATURE PLATE MUST COVER ALL

MAGNETIC POLES OF LOCK

ARMATURE PLATE MUST ROCK ON

DOOR TO ALIGN WITH LOCK

A METAL WASHER,RUBBER WASHER AND

METAL WASHER MUST BE BETWEEN

DOOR AND ARMATURE PLATE

CHECK POWER AT LOCK

CHECK POWER SUPPLY

CHECK ALL CONNECTIONS

ALIGN MAGNET IN ARMATURE PLATE WITH

DOOR STATUS SENSOR DOT ON LOCK

FOLD FORWARD ON DOTTED LINE

PLACE AGAINST HEADER

MOUNTING INSTRUCTIONS

PLACE AGAINST DOOR

DRILL 1/4” DIA. HOLE THRU DOOR

FOLLOW WITH 1/2” DIAMETER DRILL

DRILL 1/4” DIA. ANTI-ROTATION PIN HOLES 3/4” DEEP

DO NOT DRILL THRU DOOR

MODEL 600 SERIES SINGLE DRILL TEMPLATE

ALARM CONTROLS CORPORATION, DEER PARK, NY 11729

3/8” DIA.

WIRE HOLE

PLACE EDGE OF TEMPLATE

1” FROM DOOR JAMB

OPPOSITE HINGES FOR R.H.

DOOR INSTALLATION

PLACE EDGE OF TEMPLATE

1” FROM DOOR JAMB

OPPOSITE HINGES FOR L.H.

DOOR INSTALLATION

ACC600S REV. A

10/08

STEP 1

LOCATING MOUNTING HOLES

A. FOLD TEMPLATE AT DOTTED LINE.

B. PLACE BOTTOM PORTION OF

TEMPLATE AGAINST THE DOOR.

C. LOCATE AND MARK THE THREE HOLES

ON ARMATURE PLATE.

D. LOCATE AND MARK THE TWO ADJUST-

MENT HEADER PLATE HOLES AND

WIRE HOLE ON THE HEADER MOUNT-

ING PLATE.

STEP 2

INSTALLING ARMATURE PLATE

A. DRILL A LEVEL 1/4” DIA. HOLE THRU THE

DOOR. FOLLOW WITH A 1/2” DIA. DRILL.

THIS IS FOR A SOLID DOOR ONLY !

B. DRILL TWO 1/ 4” HOLES FOR THE

ANTI-ROTATION PINS 3/4” DEEP.

C. MOUNT THE ARMATURE PLATE TO

THE DOOR WITH THE SEX BOLT.

D. PLACE A METAL WASHER A RUBBER

WASHER AND A METAL WASHER ON

BOLT BETWEEN DOOR AND ARMATURE.

E. ARMATURE MUST ROCK ON DOOR.

STEP 3

HEADER MOUNTING PLATE

A. MOUNT HEADER PLATE TO JAMB USING

THE TWO ADJUSTMENT HOLES.

B. RUN THE CONTROL CABLE THRU THE

WIRE HOLE.

C. SLIDE MAGLOCK ON HEADER

MOUNTING PLATE.

D. ADJUST THE POSITION OF MAGLOCK

TO CONTACT THE ARMATURE.

E. REMOVE MAGLOCK AND SECURE

HEADER MOUNTING PLATE WITH THE

SIX REMAINING SCREWS.

STEP 4

INSTALLING MAGNET

A. SLIDE MAGLOCK ON HEADER PLATE.

B. FASTEN MAGLOCK TO HEADER PLATE

WITH THE ALLEN HEAD CAP SCREWS

LOCATED AT EACH END OF THE LOCK.

C. AFTER CHECKING FOR PROPER OPER-

ATION AND ALIGNMENT APPLY THE

SCREW LOCKING AGENT TO HEADER

MOUNTING PLATE SCREWS, ARMATURE

BOLT AND ALLEN CAP SCREWS.

ADJUSTMENT

HEADER PLATE

MOUNTING HOLE

ADJUSTMENT

HEADER PLATE

MOUNTING HOLE

HEADER MOUNTING PLATE

ARMATURE PLATE

MAGNETIC LOCK WIRING INSTRUCTIONS

MODELS

600S, 600L, 600D, 1200S, 1200L

To remove the header plate, it may be necessary to remove the wiring compartment screw. A long wiring

compartment screw can be used to increase security by limiting access to the header plate mounting

screw from below the lock.

ASSA ABLOY, the global leader

in door opening solutions

Alarm Controls Corporation

Deer Park, New York 11729

(800) 645-5538

www.alarmcontrols.com

MAGInst7-13

ALIGNMENT OF THE MAGLOCK AND ARMATURE PLATE

Align the maglock and armature plate as shown.

Armature plate must be mounted to door using the rubber washer sandwiched between the metal washers

provided. Do not excessively tighten bolt. Armature must float on door. Screw locking agent is provided on

each screw.

A terminal block is provided for wiring the maglock to the power supply.

For models 600L and 1200L

a pair of flying leads are provided for the LED. Connect the Red Lead to (V+) and

the Black LED to (V-)

ANTI-ROTATION PINS

WIRING

COMPART-

MENT

ARMATURE PLATE

MAGLOCK

MECHANICAL KICK-OFF DEVICE

UNIVERSAL MOUNTING BOLT HOLE

FOR STANDARD OR OFFSET

MOUNTING OF ARMATURE PLATE

WIRING INSTRUCTIONS

VOLTAGE IS FACTORY SET FOR 24VDC OPERATION. For 12VDC operation, access the voltage

selection switch via the wiring compartment.

600 Series 1200 Series