Alarm Lock XNarrow_DL1225 1250 26D2_WI1479C.03_INST DL1225 And DL1250 Narrow Stile Access Locks Mounting Installation Instructions X 26D2 WI1479C.03 INST

User Manual: Alarm Lock DL1225 and DL1250 Narrow Stile Access Locks Mounting and Installation Instructions Installation Manuals

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

NARROW STILE ACCESS LOCKS
345 Bayview Avenue
Amityville, New York 11701
For Sales and Repairs 1-800-ALA-LOCK
For Technical Service 1-800-645-9440
or visit us at http://tech.napcosecurity.com/
(Note: Technical Service is for security professionals only)
Publicly traded on NASDAQ Symbol: NSSC

MOUNTING AND INSTALLATION
INSTRUCTIONS

© ALARM LOCK 2013

GENERAL DESCRIPTION

The DL1225/26D2 and DL1250/26D2 are manually programmable narrow stile entry trim for Adams Rite® 1850,
1950, 4070, MS1850S and MS1950S series deadbolts for
narrow stile aluminum doors*.
The DL1225/26D2 and DL1250/26D2 will retract the existing Adams Rite® bolt when an access code is entered (or a
credential is presented) and the turnpiece turned. All locks
are equipped with a mechanical metal key override. See
OI310, OI311 or OI312 for programming information.

MECHANICAL FEATURES

The overall enclosure housing is 14 3/8" inches high, 1 5/8"
inches deep and 1¾" inches wide. An optional credential
reader can be added to the front of the housing by the factory. The trim is through-bolted to the stile of the door
(using four #10 screws) and are secured on the interior side
of the door. Supported stile thickness is 1¾".

WI1479C 6/13

• Real time clock and PC programmable automatic
lock/unlock scheduling for 500 events (1300 Series
models)
• Wide weatherproof operating range from -31 to
151ºF (-35 to 66C)
• Provides 100,000 operations using off-the-shelf long
life DL123A lithium batteries, and includes audible
and visual low battery alert
• Non-handed; fully field-reversible
• Mechanical key override; interchangeable cores supported (Corbin/Russwin, Yale, Schlage, Medeco)
• Mortise Cylinder, 1¼" supplied (supports 1-1/8", 1¼",
1-3/8" and 1½"
• Compact styling 14-3/8"H x 1-5/8"D x 1¾"W
• Backsets 31/32",1-1/8" and 1½"; stile thickness 1¾"

• DL1200/1225/1250 Series supports 100 users, fingertip/keypad programmable
• DL1300 Series supports 2000 users and includes
40,000 event audit trail and 500 event schedule. Keypad or PC programmable
• PDL1300 Series supports 2000 PIN or Prox users and
includes 40,000-event audit trail and 500 event schedule. Keypad or PC programmable
• Aluminum door retrofit outside trim for Adams Rite®
1850, 1950, 4070, MS1850S and MS1950S Series
locks
• Familiar Trilogy® programming & electronics
• All-metal, vandal-resistant 12-button keypad supports
3-6 digit PIN codes (3-5 digits on the DL1225/1250),
and multilevel user hierarchy (master, manager, supervisor and basic users)
• Keypad or PC programmable (see model information).
Quickly and easily add or delete users and enter
"passage mode", service codes, group lock-out &
group-enable
• HID Prox ID cards, keyfobs and prox tags supported in
PDL1300 series which features built-in Prox reader
(High security applications can require use of both PIN
code plus Prox ID card for access)

TABLE OF CONTENTS
GENERAL DESCRIPTION .............................................1
MECHANICAL FEATURES ............................................1
MOUNTING AND INSTALLATION .................................2
INSTALL CYLINDER .................................................3
INSTALL INTERFACE CYLINDER ......................3
INSTALL LOCK ....................................................4
INSTALL BATTERIES..........................................5
TEST OPERATION .........................................................7
NAPCO LIMITED WARRANTY ......................................8

*Adams Rite Manufacturing Co., Pomona, CA. www.adamsrite.com. All products, product
names and services described in this manual are for identification purposes only and may be
trademarks of their respective companies.

1

MOUNTING AND INSTALLATION
For factory prepped doors, use dimensions shown. Dimensions are referenced from center of 1¼" cylinder hole.
The Adams Rite® lock determines the backset.
When mounting the new Adams Rite® locks:
• Do not install the outside cylinder -- this trim replaces it;
• Do not install the faceplate (access to the cylinder set
screw in the lock is required during mounting and installation).
Mechanical Override Cylinder Cams
The DL1225/1250 trim requires the use of an oval Alarm
Lock cam (supplied with cylinder). For other manufacturers,
please see the charts below.

Cams for Standard Mortise Cylinders
Corbin-Russwin

HW1344

Marks

HW1346

Arrow

HW1348

Sargent

HW1348

Schlage

HW1349

Backset is determined by
the Adams Rite lock

Cams for IC Mortise Cylinders
Best*

HW1343

Corbin-Russwin

HW1345

Medeco

HW1347

Schlage

HW1350

Yale

HW1351

Template (use WI1459)

*Will be supplied together with Best IC Housing (HW1352)

Cylinder Length

Collar P/N

1-3/8

HW1331

1-½

HW1342

Cylinder Collars:

The DL1225/1250 can use a 1-1/8" & 1¼" mortise cylinder
without the use of a collar (1¼" requires two plastic spacers,
supplied). For cylinders longer than 1¼" a collar is required.
Order collars from an Alarm Lock distributor.

Cam for Mechanical Override Cylinder

2

Install Cylinder
1.

Install Cylinder if not already installed at the factory. Screws A & B (see Fig. 1) are correctly set at
factory. If it is difficult to screw in the cylinder, loosen
the two screws near the actuator (B) one turn. If you
find the cylinder is still difficult to screw in, then loosen
the other screws (B) one turn. Do not loosen the
screws all the way or it may be difficult to replace
them properly! Note: The trim is manufactured to
use a 1-1/8" or 1¼" Alarm Lock mortise cylinder with a
HW-1302 cam. If the cylinder that will be used is
longer than 1¼", a collar must be utilized. Please see
the collar information on the previous page.

Fig. 1c: Use 1/16" hex wrench to screw in
the cylinder back stop screw

NOTE: To remove cylinder, reverse steps 1a-1c.

Prepare the Door For "Through-Bolting"
B
A
Cylinder back stop
screw
Fig. 1: Install Cylinder if not already installed at the factory

1a. Insert key half-way into the cylinder, then screw it
in. See Fig. 1a. If cylinder will not seat flush, the cylinder back stop screw may require loosening. Cylinders
that are longer than 1¼"
will require a collar, which
will stick out from the surface when correctly installed. Please see the
cylinder information on
the previous page.
Fig. 1a: Insert key 1/2 way
into cylinder and screw in

1b. After the cylinder is screwed in all the way clockwise, turn the cylinder counter-clockwise until the
keyway is centered (see Fig. 1b). If an interchangeable core cylinder is utilized, then center the interface
toward the bottom. Tighten the screws that were loosened in step 1 (first tighten screws A then tighten
screws B).

2. Place template (WI1459)
as shown.
Important:
Place the template on top
of existing cylinder hole
and parallel to the door
edge.
2a. Drill completely through
the door for throughbolting the four mounting holes.
• IMPORTANT!--Drill
the holes STRAIGHT
THROUGH the door,
or the through-bolts
Fig. 2: Template (WI1459)
will not fit in the lock!
through-bolt holes (circled)
THIS IS ESSENTIAL!
Drill slowly and STRAIGHT through the door.
• Reposition the template as often as needed until
it is placed correctly.

Install the Interface Cylinder
3. Remove the existing cylinder (if present). Install
the new cylinder onto rear of lock. Ensure the tailpiece at the rear of the lock enters the slot of the interface cylinder. Tighten the set screw as shown in Fig.
3 below.

Screw
Interface
cylinder

Fig. 1b: Keyway centered

1c. Remove the key. Use a 1/16" hex wrench to screw
the cylinder back stop screw in fully. (See Fig. 1c)
The key should now only rotate counterclockwise.

Fig. 3: Remove old interface cylinder (if present).
Install the new cylinder and tighten the screw.

3

Install Lock
4. Install the DL lock onto the door by aligning the four
tapped mounting holes in the back of the DL lock with
the four "through-bolting" holes that were drilled in the
door in step two.

4c. Secure interface cylinder to lock by tightening the
set screw.

Fig. 4c: Secure interface cylinder to lock

Fig. 4: Install the DL lock onto the door

4a. Secure the DL lock to the door with four throughdoor mounting screws and two door plates. Place a
door plate on top of a pair of mounting holes and
loosely secure lock from the inside of the door. Snug
all four mounting screws before final tightening. Do not
over-tighten.

Important! If the interface cylinder is not parallel to
the door after tightening the set screw, then you must
verify that the original Adams Rite® lock body was
originally installed correctly (installed square to the
door). Failure to ensure the interface cylinder is installed correctly could cause lock binding or improper
operation of the lock mechanism.
4d. Install the deadbolt face plate.

Door plate

Fig. 4a: Secure lock to door -- loosely at first

4b. Cover door plates with decorative plate covers by
sliding them from top to bottom on door plates.
Fig. 4d: Install the deadbolt face plate

Fig. 4b: Slide down to install decorative plate covers

4

Install Batteries
5. Insert key in cylinder and turn counterclockwise. This
will allow access to the battery compartment screw.
With the supplied 5/64" Allen wrench, loosen the battery cover screw only until the battery cover is able
to slide off. Remove the battery pack.
Note: Loosening the battery cover screw in excess of
what is necessary may interfere with the mechanical
operation of the key override assembly. Although the
lock will not be damaged, when the key is removed the
assembly may not function until the battery cover screw
is re-tightened.

5b. Install battery pack into the battery compartment.
Neatly push all wiring inside the compartment. Holding battery in place, slide cover back on.
See Fig. 5b.

Fig. 5b: Install the battery pack

Fig. 5: Loosen battery cover screw only until the battery
cover is able to slide off

5a.

5c. While turning key counterclockwise again, allowing access to the battery cover screw, tighten the
battery cover screw fully. Turn the key clockwise and
remove.

FOR NEW INSTALLATIONS: Refer to programming instructions (OI310, OI311 or OI312) for specific instructions for "First Time Startup" and
"Change Factory Master Code" before connecting
the battery.
The lock must be powered up correctly (and have
its factory Master Code changed) or erratic lock behavior can result.

Fig. 5c: Turn key counterclockwise and
tighten the cover screw.

Test operation: See page 7.

5

NOTES

6

TEST LOCK OPERATION

Before testing, be sure the lock has been poweredup using the specific instructions in the OI310,
OI311 or OI312 manuals.

4. Retract deadbolt. Turn key clockwise and remove
key.
The turnpiece must not retract or extend the deadbolt when turned.

1. With key removed, ensure that the turnpiece CAN be
turned freely in either direction and the deadbolt
does NOT retract.

Test Step 4

Test Step 1

2. Release turnpiece.
counterclockwise.

Insert key and turn key fully

5. While pressing the default access code on the lock
keypad (press "1 2 3 4 5" on the DL1200 / DL1225 /
DL1250 and press "1 2 3 4 5 6" on the DL/PDL1300),
note the following:
• For each number key pressed, the red LED lights.
• When the "5" button is pressed (or the "6" button
on the DL/PDL1300):
1. The green LED flashes for approximately 5
seconds, and then
2. The deadbolt can be retracted when the turnpiece is turned.

Test Step 2

3. Turn the turnpiece and the deadbolt should extend
and retract.

Deadbolt
extended

Test Step 5

6. Test the exit device mounted inside (paddle / egress
bar, etc.) and confirm it is operating correctly.
SEE PROGRAMMING INSTRUCTIONS OI310,
OI311 or OI312 FOR KEYPAD PROGRAMMING
INFORMATION.

Test Step 3

7

ALARM LOCK LIMITED WARRANTY
ALARM LOCK SYSTEMS, INC. (ALARM LOCK) warrants
its products to be free from manufacturing defects in materials and workmanship for twenty four months following the
date of manufacture. ALARM LOCK will, within said period, at its option, repair or replace any product failing to
operate correctly without charge to the original purchaser
or user.

This warranty contains the entire warranty. It is the sole
warranty and any prior agreements or representations,
whether oral or written, are either merged herein or are
expressly cancelled. ALARM LOCK neither assumes, nor
authorizes any other person purporting to act on its behalf
to modify, to change, or to assume for it, any other warranty or liability concerning its products.

This warranty shall not apply to any equipment, or any part
thereof, which has been repaired by others, improperly installed, improperly used, abused, altered, damaged, subjected to acts of God, or on which any serial numbers have
been altered, defaced or removed. Seller will not be responsible for any dismantling or reinstallation charges, environmental wear and tear, normal maintenance expenses,
or shipping and freight expenses required to return products to ALARM LOCK. Additionally, this warranty shall not
cover scratches, abrasions or deterioration due to the use
of paints, solvents or other chemicals.

In no event shall ALARM LOCK be liable for an amount in
excess of ALARM LOCK's original selling price of the
product, for any loss or damage, whether direct, indirect,
incidental, consequential, or otherwise arising out of any
failure of the product. Seller's warranty, as hereinabove set
forth, shall not be enlarged, diminished or affected by and
no obligation or liability shall arise or grow out of Seller's
rendering of technical advice or service in connection with
Buyer's order of the goods furnished hereunder.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. THERE IS NO EXPRESS OR
IMPLIED WARRANTY OF MERCHANTABILITY OR A
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU
OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE
PART OF ALARM LOCK.
Any action for breach of warranty, including but not limited
to any implied warranty of merchantability, must be
brought within the six months following the end of the warranty period.
IN NO CASE SHALL ALARM LOCK BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE
LOSS OR DAMAGE IS CAUSED BY THE SELLER'S
OWN NEGLIGENCE OR FAULT.
In case of defect, contact the security professional who
installed and maintains your security system. In order to
exercise the warranty, the product must be returned by the
security professional, shipping costs prepaid and insured
to ALARM LOCK. After repair or replacement, ALARM
LOCK assumes the cost of returning products under warranty. ALARM LOCK shall have no obligation under this
warranty, or otherwise, if the product has been repaired by
others, improperly installed, improperly used, abused, altered, damaged, subjected to accident, nuisance, flood,
fire or acts of God, or on which any serial numbers have
been altered, defaced or removed. ALARM LOCK will not
be responsible for any dismantling, reassembly or reinstallation charges, environmental wear and tear, normal maintenance expenses, or shipping and freight expenses required to return products to ALARM LOCK. Additionally,
this warranty shall not cover scratches, abrasions or deterioration due to the use of paints, solvents or other chemicals.

8

ALARM LOCK RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED WEEKLY.
Warning: Despite frequent testing, and due to, but not limited to, any or all of the following; criminal tampering, electrical or communications disruption, it is possible for the
system to fail to perform as expected. ALARM LOCK does
not represent that the product/system may not be compromised or circumvented; or that the product or system will
prevent any personal injury or property loss by burglary,
robbery, fire or otherwise; nor that the product or system
will in all cases provide adequate warning or protection. A
properly installed and maintained alarm may only reduce
risk of burglary, robbery, fire or otherwise but it is not insurance or a guarantee that these events will not occur.
CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY
FOR ANY PERSONAL INJURY, PROPERTY DAMAGE,
OR OTHER LOSS BASED ON A CLAIM THE PRODUCT
FAILED TO GIVE WARNING. Therefore, the installer
should in turn advise the consumer to take any and all precautions for his or her safety including, but not limited to,
fleeing the premises and calling police or fire department,
in order to mitigate the possibilities of harm and/or damage.
ALARM LOCK is not an insurer of either the property or
safety of the user's family or employees, and limits its liability for any loss or damage including incidental or consequential damages to ALARM LOCK's original selling
price of the product regardless of the cause of such loss or
damage.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages, or differentiate in their treatment of limitations of liability for ordinary or
gross negligence, so the above limitations or exclusions
may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary
from state to state.



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2013:07:12 09:37:52-04:00
Modify Date                     : 2013:07:12 09:37:52-04:00
Page Count                      : 8
Creation Date                   : 2013:07:12 13:37:52Z
Mod Date                        : 2013:07:12 13:37:52Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : dblock
Metadata Date                   : 2013:07:12 13:37:52Z
Creator                         : dblock
Title                           : xNarrow_DL1225-1250-26D2_WI1479C.03_INST.pub

EXIF Metadata provided by EXIF.tools