AlarmForce WS7315 WATER SENSOR User Manual WS 7 315MHZ 20080204 REVISED

Download:
Mirror Download [FCC.gov]
Document ID	1023331
Application ID	Wk1IgFGZvQStoOLE4Rg1IA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.06kB (75715 bits)
Date Submitted	2008-10-30 00:00:00
Date Available	2008-10-30 00:00:00
Creation Date	2008-10-29 15:26:38
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2008-10-29 16:51:06
Document Title	Microsoft Word - WS-7 315MHZ 20080204- REVISED.DOC
Document Creator	PScript5.dll Version 5.2.2
Document Author:	cathy

Water Sensor (WS-7 315MHZ)
Water Sensor is specially designed to detect if the water level is above a certain level
that may damage your protected goods. It is a device that helps to manage your
protected place and goods by keeping it nice and dry.
Test Button
I. POWER:
The WATER SENSOR uses 4 AAA alkaline batteries as its power source. The battery is good
for at least 5 years before it needs changing.
The WATER SENSOR will only detect the low battery (< 3.6V) when an alarm has been
activated. The low battery signal will be sent to the Control Panel along with the alarm signal
transmission for the Control Panel to display the status accordingly.
II. GETTING STARTED:
Step 1:
Remove the cover by losing the two fixing screw on the top and bottom of
WATER SENSOR
Step 2:
Insert 4 AAA alkaline batteries in the battery compartment
Step 3:
Put the Control Panel into Learning Mode.
Step 4:
Press the Test Button on the Water Sensor, and a radio signal will be
transmitted to the Control Panel for learning.
Step 5:
Please refer to the panel’s manual for checking the panel’s response. If the water
sensor has not been learnt-in successfully, please repeat step 4 again.
Step 6:
Put the Control Panel back to standby mode.
Step 7:
The Learning-In process is now completed.
III. MOUNTING WATER SENSOR:
The base has two knockouts, where the plastic is thinner for mounting purpose. To mount
the SW-7:
I.
Remove the screw to separate the top cover from the base.
II.
Break through the two knockouts on the base where the plastic is thinner.
III.
Using the 2 knockouts on the base as a template, drill two holes in the
surface.
IV.
Insert the wall plugs if fixing into plaster or brick
V.
Clips the lid to the base
VI.
Screw Water Sensor to the wall
VII.
Locate the plastic clip and remove the cover from the adhesive pad
VIII.
Fix the probes within the plastic clip and firmly press the clip onto the desired
location.
IV. NORMAL OPERATION:
Mount the Water Sensor on the wall whereas drop the black wire onto the floor level or any
height that you want to detect the increasing water level.
When the probes first come in contact with water, Water Sensor sends an alarm
signal to the control panel to notify the user.

After Water Sensor enters Normal Operation Mode, please make sure to
wipe up the remnant water on the probes.
V. Supervisory Signal
If the Control Panel has not received the signal from the Water Sensor for a preset
period of time, the Control Panel will indicate it on its display to show that particular
Water Sensor is experiencing an out-of-signal problem.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Caution :
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables
when connecting to computer or peripheral devices).

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2008:10:29 16:51:06+08:00
Create Date                     : 2008:10:29 15:26:38+08:00
Metadata Date                   : 2008:10:29 16:51:06+08:00
Format                          : application/pdf
Title                           : Microsoft Word - WS-7 315MHZ 20080204- REVISED.DOC
Creator                         : cathy
Document ID                     : uuid:41ba36b7-fee0-4be6-a593-243d7c521cea
Instance ID                     : uuid:cccc33d1-5b42-475d-942a-0c74b5bb4cb4
Page Count                      : 2
Author                          : cathy

EXIF Metadata provided by EXIF.tools