Aleph America QT-001-00 Field Disturbance Sensor User Manual II QT Series US2

Aleph America Corporation Field Disturbance Sensor II QT Series US2

Contents

Users Manual

Quad-Tech Intrusion Detectors
QT Series
Select an installation height between 7 ft. (2.1 m) and 8.5 ft. (2.6 m). Optimum mounting height is 7.5 ft. (2.3m). Avoid aiming the intrusion detector
towards windows, areas exposed to direct sunlight, and heating/cooling outlets. For best performance, position the detector so its field of view is
unobstructed, and the anticipated path of an intruder will cross the PIR beam pattern.
Wire the detector to the control panel using 18 to 22 AWG conductor, standard non-shielded cable. Avoid running alarm wiring parallel to AC wiring.
Wiring knockouts and wire channel are provided in the rear cover for unobtrusive wiring. Terminal block configuration is shown in Fig. 3, below.
Prior to mounting the detector, configure jumper settings as required (see Fig. 2, below).
Pulse Count: When Pulse Count jumper is covering both pins, PC is set at 2: two to three normal steps are required to trigger an alarm. Parking the
PC jumper on one pin (or removing jumper) sets PC to 4: four to five steps will trigger an alarm.
LED Enable: When Jumper is covering both pins, the Alarm LED is enabled. The Alarm LED glows through the lookdown lens when an alarm is
signaled at the Alarm Output terminals. LED brightness automatically increases when light level in detection area is high. As room light dims so does
the LED brightness. Parking the jumper on one pin (or removing jumper) disables the Alarm LED but has no effect on the alarm output.
& Settings
Installation
Description Available with 40-foot and 60-foot protection patterns, QT Series intrusion detectors provide high quality PIR+microwave security at an outstanding value.
Front Rear
Wiring Knockouts
Corner Mount
Knockouts
Wire Channel
Cover Latch Screw
Lookdown Lens
Mounting Knockouts
Wide Angle Lens
Fig. 1: Cover Component Layout
Terminal Configuration
NC C
ALARM TAMPER
NC C
-
+
Fig. 3: Wiring Configuration
Fig. 2: PCB Layout
Compliance Information:
Separate the front and rear covers by first backing out the cover latch screw three to four full turns. Then use a small screwdriver or similar tool to release
the cover latch. To remove the PCB, push the PCB latch away from the board while grasping a terminal block and pulling the PCB out of the cover. Do
not pull on the microwave module. Refer to Figures 1 and 2, below.
performance.
Microwave
Sensitivity Adj.
Microwave Sensitivity: Microwave Sensitivity Adjustment is set to the fully clockwise position at the factory for maximum sensitivity (range).
Turn the Microwave Sensitivity Adjustment (Fig. 2) counter-clockwise to reduce sensitivity. Setting the adjustment to minimum (fully counter-clockwise)
reduces sensitivity to approximately one-third of its maximum value.
30% ~ 100%
Microwaves can “see” through walls, so in some cases, such as installation in a small room, it may be desirable to reduce microwave sensitivity.
Adjustments
Aleph’s unique “QT” signal processing evaluates PIR and microwave information while factoring in ambient temperature and light for superior “Quad-Tech”
(Factory masked
for Pet Immunity)
(furniture, stairs...) may jeopardize the pet immunity feature of the detector.
Pet Immunity: For installations where pet immunity is needed, mounting height should be no lower than 7.5 ft. (2.3m). Animal access above floor level
To ensure Pet Immunity function, do not point detector towards stairways, furniture or room fixtures to which animals have access.
Min. Max.
Features
Table
X X X X
X X X
X
X
QT-40
QT-40SL
QT-60
Feature
Model Switch
Tamper LightSelect
On/Off
LED
Count
Pulse
Immunity
60 lb. Pet
Protection
Lightning
X
X X X X
X
Select
Max. input current: 15 mA; SL model 30 mA
Security Comp.
Temp.
X
X
X
SL Front / SL Down: -- Included on Model QT-40SL -- These jumpers independently enable and disable the “Front” and “Down” Security Light (SL)
functions. SL Front controls a single white LED which shines through the front (wide angle) lens. SL Down controls two white LEDs which shine through
the lookdown lens. When enabled, Security Light operates for at least 10 seconds when motion is detected and room light is dim. Continued motion
will cause Security Light to remain on until approximately 10 seconds after motion ceases.
Jumper Settings
LED Enable
Jumper installed on both pins = LED ENABLED
Jumper removed = LED OFF
Pulse Count
Jumper installed on both pins = PC 2
Jumper removed = PC 4
Tamper
Terminal Block
Tamper
Switch
Tamper
Terminal Block
ALARM TAMPER
LED ENABLE
PULSE
COUNT
Alarm LED
PCB latch
-+
SL
FRONT
SL
DOWN
Security Light Enable*
Jumper installed on both pins = SL ENABLED
Jumper removed = SL OFF
Microwave
Module
SL Front LED*
SL Down LEDs*
*NOTE: SL features apply only to Model QT-40SL
Alarm Output: NC, 19VDC - 100 mA max
Tamper Output: NC, 30VDC - 500 mA max
Input Voltage: 10 to 16VDC, 12VDC nominal
Power
All wiring must be in accordance
with NEC, NFPA 70.
Input
Contact Aleph
Note
Automatic LED Brightness Feature
Nippon Aleph Corporation
-Security Products Headquarters-
1-28-52, Komaoka, Tsurimi-ku
Yokohama-shi, Kanagawa-ken
JAPAN, 230-0071
Tel: +81 045-575-4290 / Fax: +81 045-580-1676
E-mail: security@po.nippon-aleph.co.jp
WEB: http://www.nippon-aleph.co.jp
Aleph America Corporation
4700 Aircenter Cir, Reno, NV, 89502
USA
Tel: 775 827 8000 / Fax: 775 827 8044
E-mail: info@aleph-usa.com
WEB: http://www.aleph-usa.com
Aleph Europe Ltd.
1 Newton Close, Park Farm Industrial Estate
Wellingborough, Northamptonshire, NN8 6UW
England
Tel: 044 193 367 9600 / Fax: 044 193 340 1165
E-mail: info@alepheurope.com
WEB: http://www.alepheurope.com
The QT Series alarm LED indicator includes an automatic
brightness feature. In order to allow for a less noticeable
installation, LED brightness is reduced as the ambient light level
in the room drops.
The LED can be fully disabled by removing the ALARM LED
• This detector is designed to be incorporated into an
assume responsibility for theft or damage if the system
fails to operate.
Input Voltage
2.4 seconds, retriggerable
15 mA max. (SL model 30 mA), 11 mA quiescent (approx.)
P/N 9-900-003-00 Rev.
© 2009 Aleph America Corporation
All rights reserved
Available accessories
Specifications
jumper.
Note: Dashed lines indicate typical microwave coverage.
10 to 16 VDC, 12 VDC nominal
Dual Element
Jumper selectable: PC2, PC4
25 - 45 seconds
Red Alarm LED (Selectable On / Off)
NC, solid state, 19 VDC, 100 mA, 13 ohms resistance typ.
NC, dry contact, 30 VDC, 500 mA, 5 W max.
7 to 8.5 ft (2.1 to 2.6 m)
14° to 131° F (-10° to 55° C)
95% humidity non-condensing
4.8” H x 2.5” W x 1.7” D / 12.2cm x 6.4cm x 4.3cm
3 oz / 85 g
Input Current
Pyro Type
Pulse Count
Warm-up Time
Alarm Period
Visual Indicator
Alarm Output
Tamper Output
Mounting Height
Operating Temp.
Environmental
Weight
Dimensions
Microwave Freq.
10.525 GHz, pulsed
QT-40 & QT-40SL Main Lens: 40WAPET Wide Angle
Detection Patterns
Side View
Mid Range
Long
Range
4.5
3.0
1.5
06.0 7.5 9.0 10.5 12.0
7.5
20 6.0
4.5
8.5
3.0
1.5
0
1.5
3.0
4.5
6.0
7.5
8.5
m
25
28
15
10
5
0
5
10
15
20
25
28
0 5 10 15 20 25 30 35 40
ft
8
0
2.4
1.5 34.5 610.5 12.0
0
00
Top View
Lookdown
(Masked for PI)
• 100PET -- 100 lb pet immune lens (for QT-40 & QT-40SL only)
Unit does not power up.
Input power polarity reversed .
Apply proper input voltage.
Correct wiring polarity.
Alarm LED does not light.
Incorrect sensor mounting height or aiming.
Pulse count setting incorrect for protection
area .
Set LED jumper to “ EN ”
Alter the mounting height or aim.
Set pulse count jumper to suit the
detection requirements.
Alarm LED / Relay triggers
without movement in the
Animal / rodents in protection area.
Heating or a ir conditioning outlets in
sensor view.
Pet access to furniture or room fixture in
view of the detector (pet immune unit).
Block access of animals / rodents.
Re-aim sensor.
Ensure that pets can not climb up onto
furniture / fixtures in protection area.
An alarm is indicated at the LED Incorrect wiring at the alarm output
terminals.
Lightning damage.
Correct the wiring fault .
Replace sensor.
Alarm LED on constantly, no fault
in protected area or wiring .
.rosnesecalpeR
Troubleshooting
.
DELDEL AB
Unit continues to operate after
input power has been discon-
The wire to the “-” power input was
disconnected, the “+” is still connected.
The power is finding a return path
through the Alarm Output protection
device and alarm wiring.
Disconnect wire from the “+” power
input.
Maintenance
• INSPECTION: An inspection of this unit should be made periodically,
• CLEANING: Clean the external plastic parts of this unit with a soft,
• TESTING: This unit should be tested routinely for proper operation.
condition of the interior area and components.
including, but not limited to all mounting, wiring, and the
clean, cloth dampened with water.
At a minimum, operation should be fully checked yearly.
40ft (12m) L X 56ft (17m) W
QT-60 Main Lens: 60STD
0
5
10
15
20
25
30
35
37
5
10
15
20
25
30
35
37 0 5 10 15 20 25 30 35 40 45 50 55 60
0 1.5 3 4.5 6 7.5 9 10.5 12 13.5 15 16.5 18
10.5
9
7.5
6
4.5
3
1.5
0
1.5
3
4.5
6
7.5
9
10.5
0 5 10 15 20 25 30 35 40 45 50 55 60
0
8
0 1.5 3 4.5 6 7.5 9 10.5 12 13.5 15 16.5 18
2.4
0
m
ft
60ft (18.3m) L X 74ft (22.6m) W
Lookdown
Mid Range
Long
Range
m
ft
ft
m
7.5 9
5 10 15 20 25 30 35 40
FCC/IC Statement:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 and
ICES-003 of the FCC and Industry Canada Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV
technician for help.
The user should not modify or change this equipment
without written approval from ALEPH.
Modification could void authority to use this equipment.
FCC ID: DNHQT-001-00
IC: QT00100-xxxx
FCC/IC Information:
Patent information
US & international patents pending
Trouble Likely Causes Remedy
protection area .
but not at the alarm output.
No or low input power.
Input power polarity reversed .
nected.
Defective unit.
alarm system. As it is part of a system, Aleph cannot

Navigation menu