Alliance AWN311SP111TW01 User Manual WASHER Manuals And Guides 1205270L
User Manual: Alliance AWN311SP111TW01 AWN311SP111TW01 ALLIANCE WASHER - Manuals and Guides View the owners manual for your ALLIANCE WASHER #AWN311SP111TW01. Home:Laundry & Garment Care Parts:Alliance Parts:Alliance WASHER Manual
Open the PDF directly: View PDF 
.
Page Count: 11
| Download | |
| Open PDF In Browser | View PDF |
Installation Instructions for Topload Washers Inside ..................................... Washer Dimensions ........................................................... Before You Start ................................................................ Installation ......................................................................... Installer Checklist .............................................................. 2 2 3 Back Cover Date Purchased Model Number Serial Number Para bajar una copia de estas instrucciones en espafiol, visite www.speedqueen.com. Keep these instructions for future reference. (If this machine changes ownership, this manual must accompany machine.) Part No. 201471R3 www.speedqueen.com April 2012 Washer Dimensions --- 28 in. (71.1 cm) 22.13 in, (56.2 cm) .= _J .-_ ® in. (65 (10,2 mm) -- t 26 in. (66 cm) TLW2075N *With leveling legs turned into base. Figure 1 Before You Start Parts Included Supplies An accessories bag has been shipped washer. It includes: For most installations, are: the basic supplies you will need inside your • Two fill hoses with washers and filter screens. Refer to step 3 of Installation. • Four rubber feet. Refer to step 5 of Installation. • Beaded • Installation • User's Guide. • Warranty 1 2 4 / 5 TLW1978N 1 2 3 4 5 6 Safety Glasses Wood Block Wrench Screwdriver Pliers Level strap. Refer to step 4 of Installation. Instructions. Bond. NOTE: If the washer is delivered on a cold day (below freezing), or is stored in an unheated room or area during the cold months, do not attempt to operate it until the washer has had a chance to warm up. NOTE: Install dryer before washer. room for attaching exhaust duct. This allows Figure 2 2 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 201471 Installation Step 1" Remove Shipping Plug Remove the shipping Step 2: Wipe Out Inside of Washtub the Shipping Brace and Prior to first wash, use an all purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside of washtub. brace from under the lid. The shipping plug will be released from the base of the washer when removing the cardboard base from the washer. Refer to Figure 3. NOTE: Do not tilt washer to front or sides when moving. Save the shipping brace and plug. They must be reinstalled whenever washer is moved or transported to a new location. This will prevent damage to the washer. Refer to the User's Guide for instructions on reinstalling the shipping materials. TLW2009N Figure 4 3 \ TLW1975N 1 2 3 Shipping Brace Shipping Plug Cardboard Base Figure 3 201471 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 3 Step 3: Connect Fill Hoses NOTE: Water pressure under 20 pounds per square inch (138 kPa) will cause an extended fill time in the washer. WARNING Turn on the water faucets and flush the lines for Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If approximately two minutes to remove any foreign material that could clog the screens in the water mixing valve. the hot water system has not been used for such a period and before using the washer, turn on all hot water faucets and let the water flow from each for several NOTE: When installing in newly constructed or renovated buildings, it is very important to flush the lines since build-up may have occurred during construction. minutes. This will release any accumulated hydrogen gas. The gas is flammable. Do not smoke or use an open flame during this time. W029 Mixing Valve Flow Rates (Gallons per Minute) Hot Cold Warm (40% Hot) 35 psi 2.4 4.5 7.15 55 psi 3.5 6.2 9.2 Table 1 Water Supply Water supply faucets must fit standard 3/4 inch (19.1 mm) female garden hose couplings. DO NOT USE SLIP-ON OR CLAMP-ON CON2qECTIONS. Water supply faucets should be readily accessible to permit turning them off when washer is not being used. Recommended cold water temperature is 50 ° to 75 ° Fahrenheit (10 ° to 24 ° Celsius). Recommended maximum hot water temperature is 125 ° Fahrenheit (51 ° Celsius). Warm water is a mixture of hot and cold water. Warm water temperature is dependent upon water temperature and pressure of both the hot and cold water supply lines. Connecting Hoses Remove the two plain rubber washers and two filter screens from the accessories bag. Install them into each end of the fill hoses as shown in Figure 5. The screen must be facing outward. Screw hose couplings with the filter screens onto the water faucets until they are finger-tight. Then, using a pliers, screw approximately 1/4 turn. Use the red color-coded hose for the hot water connection and the blue color-coded hose for the cold water connection. Screw hose couplings from other end of hoses onto the water mixing valve until they are finger-tight. Then, using a pliers, screw approximately 1/4 turn. Refer to Figure 6. Make sure the red color-coded hose from the hot water faucet goes to the water mixing valve marked "H" and the blue color-coded hose from the cold faucet goes to the valve marked "C". IMPORTANT: Do not cross thread or overtighten couplings. This will cause them to leak. Turn water on and check for leaks. If leaks are found, turn off the water, unscrew hoses and reinstall them until there are no leaks. IMPORTANT: Turn off water supply whenever there will be an extended period of non-use. WARNING To prevent personal injury, avoid contact with inlet water temperatures higher than 125 ° Fahrenheit (51 ° Celsius) and hot surfaces. W748 Water pressure must be a minimum of 20 to a maximum of 120 pounds per square inch (138 to 827 kPa) static pressure measured at the faucet. 4 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 201471 Step 4: Connect Receptacle Drain Hose to Drain Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose from the retainer clamp. 3 Install the drain hose into the drain receptacle (standpipe, wall or laundry tub) following the instructions below. IMPORTANT: Drain receptacle must be capable of handling a minimum of 1-1/4 inch (32 cm) outside diameter drain hose. Standpipe 4 TLW1976N 1 2 3 4 5 Water Faucet Fill Hoses Plain Rubber Washer Place the adapter into the standpipe. The recommended height for the standpipe is 36 inches (91.44 cm). Standpipes higher than 4 feet (122 cm) are not recommended. Hose Coupling Filter Screens Figure 5 IMPORTANT: Installation: Hoses and other natural rubber parts deteriorate after extended use. Hoses may develop cracks, blisters or material wear from the temperature and constant high pressure they are subject to. All hoses should be checked on a monthly basis for any visible signs of deterioration. Any hose showing the signs of deterioration listed above should be replaced immediately. All hoses should be replaced every five years. Remove the beaded strap from accessories bag and place around standpipe and drain hose, approximately 12 inches (30 cm) down from the top of pipe and tighten strap to hold hose to standpipe. Refer to Figure 7. This will prevent the drain hose from dislodging from drain receptacle during use. IMPORTANT: To prevent siphoning, do not place any ribbed portion of the drain hose into the standpipe. I 2 \ 12 in. (30.49 cm) 36 in. (91.44 cm) Recommended Height WATER MIXING 1 VALVE 3 TLW1981N W516t 1 2 3 4 Water Faucets Cold Water Connection Hot Water Connection Fill Hoses 1 2 3 Standpipe Adapter Beaded Strap Standpipe - 2 in. (5.08 cm) or 1-1/2 in. (4 cm) Diameter Figure 7 Figure 6 201471 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 5 If standpipe is lower than 36 inches (91.44 cm), you must install No. 562P3 Siphon Break Kit. Refer to Figure 8. This kit is available (as optional equipment at extra cost) through an authorized dealer or parts distributor. Installation instructions are supplied with the kit. Laundry Tub Installation: For this type of installation, the drain hose MUST be secured to the stationary tub to prevent hose from disloding during use. Refer to Figure 10. Use the beaded strap (supplied in accessories bag) to secure hose. We recommend leaving the standpipe drain hose for this type of installation. adapter on the W512t 1 2 3 562P3 Siphon Break Kit Standpipe Drain Hose W5151 Beaded Strap (tape if necessary) Figure 8 Figure 10 Wall Installation: For installations of this type, the drain hose MUST be secured to one of the fill hoses using the beaded strap from accessories bag. Refer to Figure 9. NOTE: End of drain hose must be below height of cabinet top. 1 \ W329t 1 2 Beaded Strap (tape if necessary) Standpipe Adapter Figure 9 6 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 201471 Step 5: Position Position and Level the Washer washer so it has sufficient installation clearance for and servicing. Place washer in position on a clean, dry and reasonably firm floor. Installing the washer on any type of carpeting is not recommended. For easier access to leveling legs, prop up washer with a wooden block. Refer to Figure 11. Place rubber feet (supplied in accessories bag) on all four leveling legs. Refer to Figure 12. 5 Place a level on the cabinet top and check if the washer is level from side to side and front to back. If washer is not level, tilt washer back to access the front leveling legs. Loosen the locknuts and adjust legs by screwing into or out of washer base. Once adjusted, tilt the washer forward on front legs and lower back down into position to set the rear selfleveling legs. Make sure that the washer does not rock. When washer is level and does not rock, tighten locknuts securely against bottom of washer base. If these locknuts are not tight, washer will not remain stationary during operation. / 4 TLW1979N 1 2 Level Locknut 3 Leveling Leg 4 5 Rubber Cup Washer Base Figure 12 Improper installation or flexing of a weak floor will cause excessive vibration. Do not slide washer across floor once the leveling legs have been extended. Legs and base could become damaged. Verify that washer does not rock. 1 \ TLW1977N Wood Block Figure 11 201471 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 7 Step 6: Plug in the Washer When plugging Washer requires 120 Volt, 60 Hertz electrical supply and comes equipped with a 3-Prong grounding plug. Refer to serial plate for specific electrical requirements. in the washer: DO NOT overload circuits. DO NOT use an extension cord. DO NOT use an adapter. DO NOT operate both a washer and gas dryer on the same circuit. Use separately fused 15 Amp circuits. 2 The washer is designed to be operated on a separate branch, polarized, three-wire, effectively grounded, 120 Volt, 60 Hertz, AC (alternating current) circuit protected by a 15 Amp fuse, equivalent fusetron or circuit breaker. The three-prong grounding plug on the power cord should be plugged directly into a polarized three-slot effectively grounded receptacle rated 110/120 Volts AC (alternating current) 15 Amps. Refer to Fig_lre 13 to determine correct polarity of the wall receptacle. 120+12 V.A.C. Standard 120 Volt, 60 3-Wire Effectively Grounded Circuit WARNING DRY2022N 1 2 L1 Ground 3 4 5 Neutral Side To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the washer to the electric power source. W082 Round Grounding Prong Neutral Figure 13 WARNING To reduce the risk of fire, electric shock, serious injury or death, all wiring and grounding MUST conform with the latest edition of the National Electrical Code, ANSI/NFPA No. 70, and such local regulations as might apply. It is the customer's responsibility to have the wiring, fuses and circuit breakers installed by a qualified electrician to make sure adequate electrical power is available to the washer. W518 8 © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 201471 Grounding Information Step 7: Add Water to the Washer The washer must be grounded. In the event of malfunction or breakdown, grounding will reduce risk of electric shock by providing a path of least resistance for electric current. the The washer is equipped with a cord having an equipment-grounding conductor and a 3-prong grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. To prevent damage to pump, do not run washer before adding at least one quart water to the tub. If the washer is run before any water is added, the pump seal may overheat causing the pump to leak. Once installed, the water retained in the drain system from the previous cycle will provide sufficient cooling to prevent pump seal damage. NOTE: The agitator should not be removed except for service. The washtub is designed to be selfcleaning. WARNING Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the washer is properly grounded. W216 Do not modify the plug provided with the washer - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. NOTE: Have a qualified electrician check the polarity of the wall receptacle. If a voltage reading is measured other than that in Figure 13, the qualified electrician should correct the problem. W3911 Figure 14 WARNING This unit is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. W213 NOTE: The wiring control hood. 201471 diagram is located in the © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 9 Step 8: Check Lid Switch Washer should stop agitating opened. and spinning when lid is W376t Figure 15 Step 9: Check Installation Refer to Installer Checklist on the back cover of this manual and make sure that washer is installed correctly. Run washer through one complete it is operating properly. 10 cycle to make sure © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT 201471 Installer Checklist Fast Track for Installing the Washer (Refer to the manual O • Remove Shipping Shipping the Brace Plug. for more detailed information) I 1 and LEVEL the Washer. Position CHECK and Level [ (_) _ D(_2SI CHECK W316t TLW1975N • Wipe Out Inside • of Washtub. Plug in the Washer. J TLW2009N CHECK CHECK • Connect D254t Filter Screens Fill Cold Valve Connection • Add Water Washer. to the Red _, Hoses. Plain Washers CHECK CHECK TLW1988N W391t Connect to Drain Drain Hose Receptacle. Check Lid Switch. J CHECK CHECK W315tEOA © Copyright, Alliance Laundry Systems LLC - DO NOT COPY or TRANSMIT W391I
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 11 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Fri Jun 01 04:15:23 2012 Author : Title : Subject :EXIF Metadata provided by EXIF.tools