Allied Telesis K K TQ3600 Wireless access point with PoE powered device function User Manual at001862c

Download:
Mirror Download [FCC.gov]
Document ID	2220040
Application ID	pXZEUjzykhLmDcfgptqSyw==
Document Description	User manual (statement)
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	143.17kB (1789656 bits)
Date Submitted	2014-03-19 00:00:00
Date Available	2014-05-22 00:00:00
Creation Date	2004-08-18 14:26:09
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2014-03-06 19:02:46
Document Title	at001862c.fm
Document Creator	FrameMaker 9.0
Document Author:	sborsuk

Review Draft - January 24, 2014
Installation Options
Quick Installation Guide
AT-TQ3600
Wireless Access Point

Table or desktop

Wall or ceiling
These two figures identify the components of the access point.
Installation and User’s Guides
This quick installation guide explains how to install the device on a table or desktop. For
instructions on how to install the device on a wall of ceiling, refer to the AT-TQ3600
Wireless Access Point installation Guide.
This document contains an abbreviated version of the installation instructions for the
AT-TQ3600 Wireless Access Point. For complete installation and management
instructions, refer to the AT-TQ3600 installation Guide and AT-TQ Wireless Access Point
Series User’s Guide on the Allied Telesis web site at www.alliedtelesis.com/support.
Note:
The non-US model of this product has a country code setting that must be set during the
initial management session of the unit. The setting ensures that the unit operates in
compliance with the laws and regulations of your country or region.
CONSOLE
RESET
3101
Safety and Electromagnetic Emissions Certificates
Standard
Compliance
Certificates
RoHs compliant
European Union RoHS (Directive 2011/65/EU of the European
Parliament and of the Council of 8 June 2011 on the restriction of
the use of certain hazardous substances in electrical and
electronic equipment.)
CE
FCC/IC
RCM
Wi-Fi CERTIFIED
The country code for the US model is preset and cannot be changed. Per FCC regulations,
the country code setting for all WiFi products marketed in the US must be fixed to US
operational channels only.
PWR
SYS
3600
Medical (EMC)
EN 60601-1-2
Radio Equipment
EN 300 328
AS/NZS 4268
RSS-Gen
FCC 47 CFR Part 15,
Subpart C
FCC part 2
Safety
The AT-TQ3600 Wireless Access Point is shown in this figure.
EAC
KC
SRMC
EN 301 489-1
EN 301 489-17
EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-11
AS/NZS CISPR 22
FCC 47 CFR Part 15, Subpart B
ICES-003
Physical Description
AT-T
Electromagnetic
Compatibility (EMC)
10M
100M
2.4G
Hz
5GH
3121
3122
4 5
The components on the access point are described in this table.
The LEDs on the top panel of the access point are described in this table.
Table 2. Access Point Components
Table 1. LEDs
LED
EN 301 893
RSS210
RSS-102
FCC 47 CFR Part 15,
Subpart E
PWR
EN 60950-1
IEC 60950-1
TUV-T
UL 60950-1
UL 2043 (For AT-TQ3600-01 only)
Suitable for use in environmental air space in accordance with
Section 300-22(C) of the National Electrical Code, and Sections
2-128, 12-010(3), and 12-100 of the Canadian Electrical Code
Part 1, CSA C22.1.
SYS
10M and
100M
State
Description
Solid
Green
The unit is receiving DC power that is within the normal
operating range.
Off
The power supply is not receiving power from either the
AC/DC power adapter or a PoE Ethernet switch.
Amber
The access point is loading its firmware.
Off
The unit is operating normally.
10M: On
The Ethernet port is operating at 10 Mbps.
100M: Off
10M: Off
The Ethernet port is operating at 100 Mbps.
Component
Description
Holes for antitheft devices
Refer to “Installing Anti-theft Devices”.
Console Port
The Console Port is for manufacturing purposes only.
Reset Button
The Reset button returns the parameter settings on the access
point to their default settings.
LAN Port
The 10/100/1000Base-T LAN port connects the access point to
your wired network. It supports PoE. If you connect the port to an
Ethernet switch that supports PoE, you do not have to use the
power adapter to power the device.
DC Power
Connector
This connector is for the AT-TQ0091 AC/DC Power Adapter. You
may power the access point with PoE on the LAN port or the
power adapter. The power adapter must be ordered separately.
100M: On
10M: On
You should review the safety precautions in the AT-TQ3600 Wireless Access Point
Installation Guide before installing the product.
The Ethernet port is operating at 1000 Mbps.
100M: On
*613-001862 Rev B*
613-001862 Rev. C
2.4GHz
Green
The 2.4GHz radio is sending and receiving radio waves.
5GHz
Green
The 5GHz radio is sending and receiving radio waves.
The cable specifications for the LAN port are detailed in the AT-TQ3600 Wireless Access
Point Installation Guide.
You may turn off the LEDs with the management software.
Package Contents of the AT-TQ3600 Wireless Access Point
3.
The following items should be in the shipping container:

One AT-TQ3600 Wireless Access Point

This AT-TQ3600 Quick Install Guide
Review Draft - January 24, 2014
Route a network cable through the notch in the cover and under the bottom panel,
and connect it to the LAN port on the access point.
8.
Check the plug on the AT-TQ0091 AC/DC Power Adapter to see if it is the correct
plug for your region. If it is not the correct plug, remove it by pressing down on the
release tab and sliding it from the slot on the adapter.
Release Tab
Package Contents of the AT-TQ0091 AC/DC Power Adapter
If you are not planing to use the PoE feature of the access point to power the device, you
must separately order the AT-TQ0091 AC/DC Power Adapter. The adapter comes with four
regional power connectors. (The adapter comes with one connector already installed.)
3124
3116
9.
4.
Connect the other end of the network cable to a port on an Ethernet switch.
5.
Do one of the following:
3126
If any item is missing or damaged, contact your Allied Telesis sales representative for
assistance. You should retain the original shipping material in case you need to return the
unit to Allied Telesis.
6.
Installing the Wireless Access Point on a Table or Desk

If you are not using the PoE feature on the Ethernet LAN Port to power the unit,
continue with this procedure to attach the AT-TQ0091 AC/DC Power Adapter.

If you are using the PoE feature on the LAN Port to power the access point, turn
the access point right side up. The installation procedure is complete. Go to
“Installing Anti-theft Devices” or “Starting the Initial Management Session”.
Route the DC power cable from the AT-TQ0091 AC/DC Power Adapter through the
notch in the cover and under the bottom panel, and connect it to the DC-IN 12VDC
connector on the access point.
To install the access point on a table or desktop, perform the following procedure:
Place the access point upside down on the table or desk selected for the device.
2.
Install the four rubber feet included with the wireless access point to the bottom
panel.
3125
10. Connect the adapter to an appropriate AC power source.
Installing Anti-theft Devices
The access point has holes for anti-theft devices. You may want to install one or more
anti-theft devices if the access point is installed in a non-secure area. Anti-theft devices
are not available from Allied Telesis. The holes for anti-theft devices are identified in this
figure. A Kensington lock should be used when the device is installed on a table or desk.
A padlock or Torx or similar screw works only when the device is installed on a wall or
ceiling.
For instructions on how to install the device on a wall or ceiling, refer to the AT-TQ3600
Wireless Access Point Installation Guide.
1.
Slide the correct plug for your region into the slot on the adapter until it clicks into
place.
PW
3117
SY
10
0M
10
2.
AT
-T
4G
5G
Q3
60
3118
7.
Turn the access point right side up.
3123
Padlock
Torx or similar
screw (M3 x 4mm)
Kensington
Lock
Review Draft - January 24, 2014
Starting the Initial Management Session
This section contains an abbreviated version of the procedure for starting the initial
management session. For complete instructions, refer to the AT-TQ3600 installation Guide
or AT-TQ Wireless Access Point Series User’s Guide.
The wireless access point has a DHCP client. The default setting for the client is enabled.
When you power on the access point for the first time, it queries the subnet on the LAN port
for a DHCP server. If a DHCP server responds to its query, the unit uses the IP address the
server assigns to it. If there is no DHCP server, the access point uses the default IP
address 192.168.1.230.
Note:
If the Country pull-down menu is deactivated and cannot be changed, the country
parameter was set when the unit was manufactured and cannot be changed. If the setting
is not correct for your country or region, contact your Allied Telesis sales representative for
assistance.
The access point displays a confirmation prompt.
3.
If you click OK, the access point changes the country setting and disables both radios
on the access point. (The default setting for the radios is disabled.)
To start the initial management session, perform the following procedure:
1.
Start the web browser on your management workstation.
2.
Enter in the URL field of the web browser the IP address of the wireless access
point. The address is one of the following:

If your network does not have a DHCP server, enter the default address
192.168.1.230.

Click OK to change the country setting or Cancel to cancel the procedure.
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions
suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
This procedure does not require clicking the Update button.
You must now reboot the access point. The new country setting is not active until the
unit is rebooted. To reboot the unit, either power off and on the unit or continue with
these steps:
If your network has a DHCP server, enter the IP address the DHCP server assigned to
the access point.
4.
From the Maintenance menu, select Configuration.
5.
Click the Reboot button in the To Reboot the Access Point section of the “Manage
the Access Point’s Configuration” window.
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and
5470-5725 MHz shall comply with the e.i.r.p. limit; and
6.
When the access point displays a confirmation prompt, click OK to reboot the unit or
Cancel to cancel the procedure.
7.
To resume managing the unit, wait for it to complete initializing its management
software and then start a new management session.
(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall
comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as
appropriate.
For more instructions on how to configure the features of the access point, refer to the
AT-TQ Wireless Access Point Series User’s Guide.
Federal Communication Commission Interference Statement
Enter “manager” for the username and “friend” for the password. The username and
password are case-sensitive.
Setting the Country Setting
Note:
The non-US model of this product has a country code setting that must be set during the
initial management session of the unit. The setting ensures that the unit operates in
compliance with the laws and regulations of your country or region.
The country code for the US model is preset and cannot be changed. Per FCC regulations,
the country code setting for all WiFi products marketed in the US must be fixed to US
operational channels only.
Caution:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
The wireless access point displays the logon prompt.
3.
Industry Canada Statement
(iv) Users should also be advised that high-power radars are allocated as primary users
(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars
could cause interference and/or damage to LE-LAN devices.
Avertissement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions
précises sur les restrictions susmentionnées, notamment:
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement
pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350
MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.;
(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825
MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non
point à point, selon le cas.

Reorient or relocate the receiving antenna.
To set the country setting, perform the following procedure:

Increase the separation between the equipment and receiver.
(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de
haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les
bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du
brouillage et/ou des dommages aux dispositifs LAN-EL.
1.

Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Radiation Exposure Statement:

Consult the dealer or an experienced radio/TV technician for help.
Select Wireless Settings from the Manage menu.
The access point displays the “Modify wireless settings” window.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
21cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Déclaration d'exposition aux radiations:
For operation within 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range, it is restricted to
indoor environment. The band from 5600-5650MHz will be disabled by the software during
the manufacturing and cannot be changed by the end user. This device meets all the other
requirements specified in Part 15E, Section 15.407 of the FCC Rules.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 21 cm de distance entre la source de rayonnement et votre corps.
Radiation Exposure Statement
2.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
21cm between the radiator & your body.
Select the Country pull-down menu and select your country or region.
Review Draft - January 24, 2014
European Union Restriction of the Use of Certain Hazardous
Substances
(RoHS) in Electrical and Electronic Equipment
This Allied Telesis RoHS-compliant product conforms to the European Union Restriction of
the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment.
Allied Telesis ensures RoHS conformance by requiring supplier Declarations of Conformity,
monitoring incoming materials, and maintaining manufacturing process controls.
Dimensions (W x D x 200.0 mm x 200.0 mm x 66.0 mm
H)
(7.9 in. x 7.9 in. x 2.6 in.)
0° C to 45° C (32° F to 113° F)
Français
[French]
Par la présente Allied Telesis déclare que l'appareil wireless access point
est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la directive 1999/5/CE.
Operating
Temperature of the
Access Point When
Using PoE
0° C to 40° C (32° F to 104° F)
Italiano [Italian]
Con la presente Allied Telesis dichiara che questo wireless access point è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite
dalla direttiva 1999/5/CE.
Operating
Temperature of the
Access Point When
Using the AC/DC
Adapter
Latviski [Latvian]
Ar šo Allied Telesis deklarē, ka wireless access point atbilst Direktīvas
1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Storage
Temperature
-20° C to 70° C (-4° F to 158° F)
Lietuvių
[Lithuanian]
Šiuo Allied Telesis deklaruoja, kad šis wireless access point atitinka
esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Operating Humidity
5% to 80% non-condensing
Storage Humidity
5% to 95% non-condensing
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio equipment and services; Part 1: Common
technical requirements.
Nederlands
[Dutch]
Hierbij verklaart Allied Telesis dat het toestel wireless access point in
overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
EN 301 489-17
Malti [Maltese]
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic
Compatibility (EMC) standard for radio equipment and services; Part 17: Specific
conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance
RLAN equipment
Magyar
[Hungarian]
Alulírott, Allied Telesis nyilatkozom, hogy a wireless access point megfelel
a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb
elõírásainak.
Polski [Polish]
Niniejszym Allied Telesis oświadcza, że wireless access point jest zgodny
z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami
Dyrektywy 1999/5/EC.
Português
[Portuguese]
Allied Telesis declara que este wireless access point está conforme com
os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Slovensko
[Slovenian]
Allied Telesis izjavlja, da je ta wireless access point v skladu z bistvenimi
zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak]
Allied Telesis týmto vyhlasuje, že wireless access point spĺňa základné
požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
Suomi [Finnish]
Allied Telesis vakuuttaa täten että wireless access point tyyppinen laite on
direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin
muiden ehtojen mukainen.
EN60950-1
EN 300 328
EN 301 893
Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN;
Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive

Español
[Spanish]
Physical Specifications
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Allied Telesis ΔΗΛΩΝΕΙ ΟΤΙ wireless access point
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ
ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband
Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM
band and using spread spectrum modulation techniques; Harmonized EN covering
essential requirements under article 3.2 of the R&TTE Directive,

Hereby, Allied Telesis, declares that this wireless access point is in
compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC.
Ελληνική
[Greek]
Safety of Information Technology Equipment

English
Weight
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
The following test methods have been applied in order to prove presumption of conformity
with the essential requirements of the R&TTE Directive 1999/5/EC:

Käesolevaga kinnitab Allied Telesis seadme wireless access point
vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele.
Por medio de la presente Allied Telesis declara que el wireless access
point cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Europe - EU Declaration of Conformity

Product Specifications
Eesti [Estonian]
EN 301 489-1
This device is a 5GHz wideband transmission system (transceiver), intended for use in all
EU member states and EFTA countries, except in France and Italy where restrictive use
applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order
to obtain authorization to use the device for setting up outdoor radio links and/or for
supplying public access to telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some areas
the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 2483.5 MHz. For detailed information the end-user should contact the national spectrum
authority in France.
0700
Česky [Czech]
Allied Telesis tímto prohlašuje, že tento wireless access point je ve shodě
se základními požadavky a dalšími příslušnými ustanoveními směrnice
1999/5/ES.
Dansk [Danish]
Undertegnede Allied Telesis erklærer herved, at følgende udstyr wireless
access point overholder de væsentlige krav og øvrige relevante krav i
direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt Allied Telesis, dass sich das Gerät wireless access point in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
10
Svenska
[Swedish]
1.2 kg (2.6 lb.)
Environmental Specifications
Maximum Power Consumption
AT-TQ3600 Access
Point
Hawnhekk, Allied Telesis, jiddikjara li dan wireless access point
jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li
hemm fid-Dirrettiva 1999/5/EC.
12 watts
AT-TQ0091 AC/DC Power Adapter
Input Range
100~240 Vac
Input Frequency
47-63 Hz
Input Power
Consumption (no
load)
<0.3W max.
Output Voltage
+12 VDC
Output Current
2A max.
Copyright  2014 Allied Telesis, Inc.
All rights reserved.
Härmed intygar Allied Telesis att denna wireless access point står I
överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
No part of this publication may be reproduced without prior written permission from Allied
Telesis, Inc.
Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All
other product names, company names, logos or other designations mentioned herein are
trademarks or registered trademarks of their respective owners.
Allied Telesis, Inc. reserves the right to make changes in specifications and other
information contained in this document without prior written notice. The information
provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be
liable for any incidental, special, indirect, or consequential damages whatsoever, including
but not limited to lost profits, arising out of or related to this manual or the information
contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have
known, the possibility of such damages.
11
12

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Annotate, Fill forms
Page Mode                       : UseNone
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2004:08:18 14:26:09Z
Creator Tool                    : FrameMaker 9.0
Modify Date                     : 2014:03:06 19:02:46+08:00
Metadata Date                   : 2014:03:06 19:02:46+08:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Format                          : application/pdf
Title                           : at001862c.fm
Creator                         : sborsuk
Document ID                     : uuid:31745bbe-77a6-4f93-9bc6-b7b06c3a72ca
Instance ID                     : uuid:05beb87b-7a13-4e4f-af98-11b709e97521
Has XFA                         : No
Page Count                      : 4
Author                          : sborsuk

EXIF Metadata provided by EXIF.tools