Alpha Networks WMPA01A1 Wireless Mini PCI Adapter User Manual WMP A01 User s Munaul

Alpha Networks Inc. Wireless Mini PCI Adapter WMP A01 User s Munaul

User Manual

Download: Alpha Networks WMPA01A1 Wireless Mini PCI Adapter User Manual WMP A01 User s Munaul
Mirror Download [FCC.gov]Alpha Networks WMPA01A1 Wireless Mini PCI Adapter User Manual WMP A01 User s Munaul
Document ID1437942
Application IDM+I4RJPpPs4vUm9kepwDBw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize20.61kB (257657 bits)
Date Submitted2011-03-25 00:00:00
Date Available2011-03-25 00:00:00
Creation Date2011-01-20 17:46:36
Producing SoftwareAcrobat Distiller 8.1.0 (Windows)
Document Lastmod2011-01-20 17:56:07
Document TitleMicrosoft Word - WMP-A01 User's Munaul.doc
Document CreatorPScript5.dll Version 5.2.2
Document Author: sam

User Manual
For
WMP-A01
Wireless Mini PCI adapter
Version: 1.1
2011/1/13
This document contains confidential proprietary information and is the property of
Alpha Networks Corporation. The contents of this document may not be disclosed to
unauthorized persons without the written consent of Alpha Networks Corporation.
Contents
TEST OPERATION MANUAL............................................................................................................4
Test Utility Installation:....................................................................................................................4
Configuration: ..................................................................................................................................5
1.0 SCOPE...............................................................................................................................................6
1.1 DOCUMENT......................................................................................................................................6
1.2 PRODUCT FEATURES........................................................................................................................6
2.0 REQUIREMENTS ...........................................................................................................................7
2.1 GENERAL REQUIREMENTS ...............................................................................................................7
2.1.1 General Section .......................................................................................................................7
2.2 REQUIREMENTS OF RELIABILITY, MAINTAINABILITY AND QUALITY ...............................................7
2.3 ENVIRONMENTAL REQUIREMENTS ..................................................................................................7
END PRODUCT LABELING.........................................................................................................................9
MANUAL INFORMATION TO THE END USER.........................................................................................10
IMPORTANT NOTE:..........................................................................................................................11
END PRODUCT LABELING .............................................................................................................11
MANUAL INFORMATION TO THE END USER ..........................................................................11
Test Operation Manual
Test Utility Installation:
1. Unzip “ART_V0_5_b25ALL.zip” to “C:\”.
2. The utility must run on Win2000 or WinXP.
Hardware Installation:
Before insert the card, please execute the below instruction at first !!
1.
Win2000 OS :
Enter in the directory : C:\ v0_5_b25ALL\art_driver\bin\2000
Execute the uninst_new_drv_2k.bat:
Execute the inst_new_drv_2k.bat :
WinXP OS :
Enter in the directory : C:\ v0_5_b25ALL\art_driver\bin\xp
Execute the uninst_new_drv_xp.bat:
Execute the inst_new_drv_xp.bat
2. Insert the card, then install the driver , the driver is located at
Win2000 OS :
C:\ v0_5_b25ALL\art_driver\bin\2000
WinXP OS :
C:\ v0_5_b25ALL\art_driver\bin\xp
Configuration:
1. Enter the DOS command mode , then change the directory to :
C:\ v0_5_b25ALL\art_driver\bin\xp
2. Input the instruction: art \id=2082
Then press enter .
ART TEST MODE:
1. Once utility is executed, a menu with test options will appear. To run a test, press
the character key that is assigned to the test option.
For example, press “c” to run the continuous transmit test, or press “r ” to run the
continuous receive test.
For example: press “o” to change 11g or 11b test mode, Press “c” to continuous
transmit mode .
2. Continuous Transmit Options.
a. Before the Continuous Transmit test, need to press “e” first
The command will load the calibrate data to the EEROM, then the card can
transmit the target power
b. The channel frequency, data rate and output power could be changed in
continuous transmit options. Press “c” to increase the output power , 11g Power
(data rate 6Mbps) is 17dBm, 11b Power is 17dBm , Press ESC to return to the
main Test Options menu when finished.
3. Continuous Receive Options
Continuous receive options will put the radio into receive mode to allow for
radio measurements. Press ESC to return to the main Test Options menu when
finished.
1.0 Scope
1.1 Document
This document is to specify the product requirements for 802.111a/n Wireless
Mini PCI adapter. This mPCI is based on Atheros chipset that complied with
complied with IEEE 802.11n , and it is also backward complied with IEEE
802.11a standard from 5.15~5.825GHz wideband . It can be used to provide
up to 54Mbps for IEEE 802.11a and 300Mbps for IEEE 802.11n to connect
your wireless LAN.
1.2 Product Features
Compatible with IEEE 802.11a high rate standard to provide wireless
54Mbps data rate
Compatible with IEEE 802.11 n standard to provide wireless 300Mbps
data rate
Maximum reliability, throughput and connectivity with automatic data rate
switching
Supports infrastructure networks via Access Point and ad-hoc network via
peer-to-peer communication
2.0 Requirements
The following sections identify the detailed requirements of the 802.111a/n
Wireless Mini PCI adapter.
2.1 General Requirements
2.1.1 General Section
Feature
2.1.1.1
2.1.1.2
Antenna Type
Operating
Voltage
Form
Factor y
and
Interface
2.1.13
Detailed Description
I-pex compatible connectors
3.3VDC +/- 10%
Mini-PCI type III A form factor
2.2 Requirements of Reliability,
Maintainability and Quality
Feature
Detailed Description
2.2.1
2.22
2.2.3
MTBF
Maintainability
Quality
Mean Time Between Failure > 30,000 hours
There is no scheduled preventive maintenance required
The product quality is followed-up by Alpha Networks
factory quality control system
2.3 Environmental Requirements
Feature
Detailed Description
2.3.1
Operating
Temperature
Conditions
The product is capable of continuous reliable operation
when operating in ambient temperature of 0 ℃ to +50℃.
2.3.2
Non-Operating
Temperature
Conditions
Neither subassemblies is damaged nor the operational
performance is degraded when restored to the operating
temperature after exposing to storage temperature in the
range of –20 ℃ to +75 ℃.
#
Feature
2.3.3
Operating
Humidity
conditions
2.34
Non-Operating
Humidity
Conditions
Detailed Description
The product is capable of continuous reliable operation when subjected
to relative humidity in the range of 10% and 90% non-condensing.
The product is not damaged nor the performance is
degraded after exposure to relative humidity ranging from
5% to 95% non-condensing
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
‐
Reorient or relocate the receiving antenna.
‐
Increase the separation between the equipment and receiver.
‐
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
‐
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This transmitter must not be co‐located or operating in conjunction with any other antenna or
transmitter.
Operations in the 5.15‐5.25GHz band are restricted to indoor usage only
IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware‐limited to channels
1 through 11.
This device is intended only for OEM integrators under the following conditions:
1)
The antenna must be installed such that 20 cm is maintained between the antenna and
users, and
2)
The transmitter module may not be co‐located with any other transmitter or antenna,
3)
For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for
2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the
end‐user regarding to Regulatory Domain change.
As long as 3 conditions above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end‐product for any additional
compliance requirements required with this module installed (for example, digital device
emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain
laptop configurations or co‐location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re‐evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product
must be labeled in a visible area with the following: “Contains FCC ID: RRKWMPA01A1”.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how
to install or remove this RF module in the user’s manual of the end product which integrates
this module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
Industry Canada Statement
This device complies with RSS‐210 of the Industry Canada Rules. Operation is subject to the
following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired
operation of the device
This device has been designed to operate with an antenna having a maximum gain of 4.6dBi (Peak
Gain, Included cable loss)
Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The
required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the EIRP is not more than required for successful communication.
This radio transmitter IC 4833A‐WMPA01A1 has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain and
required antenna impedance for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
Approved antenna list: Impedance 50 ohm.
Caution:
The device for the band 5150‐5250 MHz is only for indoor usage to reduce potential for harmful
interference to co‐channel mobile satellite systems.
Because high power radars are allocated as primary users (meaning they have priority) in
5250‐5350 MHz and 5650‐5850 MHz, these radars could cause interference and/or damage to
license exempt LAN devices.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and
users, and
2) The transmitter module may not be co-located with any other transmitter or antenna,
3)
For all products market in Canada, OEM has to limit the operation channels in CH1
to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any
tool or info to the end-user regarding to Regulatory Domain change.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada authorization is
no longer considered valid and the IC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains IC:
4833A-WMPA01A1”.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to other
users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions
suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
(Le manuel d'utilisation de dispositifs émetteurs équipés d'antennes amovibles doit
contenir les informations suivantes dans un endroit bien en vue:)
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de
dB [4.6]. Une antenne à gain plus élevé est strictement interdite par les règlements
d'Industrie Canada. L'impédance d'antenne requise est de 50 ohms.
Avertissement:
Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour
une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux.
Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux
(c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que
ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes: (Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée
entre l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne,
3) Pour tous les produits vendus au Canada, OEM doit limiter les fréquences de
fonctionnement CH1 à CH11 pour bandes de fréquences 2.4G grâce aux outils de
microprogrammation fournis. OEM ne doit pas fournir d'outil ou d'informations à
l'utilisateur final en ce qui concerne le changement de réglementation de domaine.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co‐localisation avec un autre émetteur),
l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le
produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final
(y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne
peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et
les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription
suivante: "Contient des IC: 4833A-WMPA01A1".
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant
à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final
qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et
avertissements comme indiqué dans ce manuel.
Conform é ment à
la r é glementation d'Industrie Canada, le pr é sent é metteur radio
peutfonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé
pourl'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectriqueà l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de
sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire àl'établissement d'une communication satisfaisante.
以下警語適用台灣地區
經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大
功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,
並改善至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射
頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
在5.25-5.35秭赫(GHz)頻帶內操作之無線資訊傳輸設備,限於室內使用。
本模組於取得認證後將依規定於模組本體標示審合格籤,並要求平台上標示「本產品內含射頻模
組:ID編號」

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2011:01:20 17:56:07+08:00
Create Date                     : 2011:01:20 17:46:36+08:00
Metadata Date                   : 2011:01:20 17:56:07+08:00
Format                          : application/pdf
Title                           : Microsoft Word - WMP-A01 User's Munaul.doc
Creator                         : sam
Document ID                     : uuid:5dc6b9d8-49ad-4300-938c-1bd3c4b8cf2a
Instance ID                     : uuid:7c9aeefa-2073-41bf-89a4-5d190f1c4a8f
Page Count                      : 14
Author                          : sam
EXIF Metadata provided by EXIF.tools
FCC ID Filing: RRKWMPA01A1

Navigation menu