Alpha Networks WMPN09HB1 Wireless Mini PCI Adapter User Manual WMP N09H User s Munaul

Alpha Networks Inc. Wireless Mini PCI Adapter WMP N09H User s Munaul

User Manual

User Manual For WMP-N09H 無線網路卡 Wireless Mini PCI Adapter
Version: 1.1 2011/1/13 This document contains confidential proprietary information and is the property of Alpha Networks Corporation. The contents of this document may not be disclosed to unauthorized persons without the written consent of Alpha Networks Corporation.
Contents TEST OPERATION MANUAL............................................................................................................4 Test Utility Installation:....................................................................................................................4 Configuration:..................................................................................................................................5 1.0 SCOPE...............................................................................................................................................6 1.1 DOCUMENT......................................................................................................................................6 1.2 PRODUCT FEATURES........................................................................................................................6 2.0 REQUIREMENTS...........................................................................................................................6 2.1 GENERAL REQUIREMENTS...............................................................................................................7 2.1.1 General Section .......................................................................................................................7 2.2 REQUIREMENTS OF RELIABILITY, MAINTAINABILITY AND QUALITY...............................................7 2.3 ENVIRONMENTAL REQUIREMENTS ..................................................................................................7 ENDPRODUCTLABELING.........................................................................................................................9 MANUALINFORMATIONTOTHEENDUSER...........................................................................................9
Test Operation Manual Test Utility Installation: 1. Unzip “ART_V0_5_b25ALL.zip” to “C:\”. 2. The utility must run on Win2000 or WinXP. Hardware Installation: Before insert the card, please execute the below instruction at first !! 1. Win2000 OS : Enter in the directory : C:\ v0_5_b25ALL\art_driver\bin\2000 Execute the uninst_new_drv_2k.bat: Execute the inst_new_drv_2k.bat : WinXP OS : Enter in the directory : C:\ v0_5_b25ALL\art_driver\bin\xp Execute the uninst_new_drv_xp.bat: Execute the inst_new_drv_xp.bat 2. Insert the card, then install the driver , the driver is located at Win2000 OS : C:\ v0_5_b25ALL\art_driver\bin\2000 WinXP OS : C:\ v0_5_b25ALL\art_driver\bin\xp
Configuration: 1. Enter the DOS command mode , then change the directory to : C:\ v0_5_b25ALL\art_driver\bin\xp 2. Input the instruction: art \id=2082 Then press enter . ART TEST MODE: 1. Once utility is executed, a menu with test options will appear. To run a test, press the character key that is assigned to the test option. For example, press “c” to run the continuous transmit test, or press “r ” to run the continuous receive test. For example: press “o” to change 11g or 11b test mode, Press “c” to continuous transmit mode . 2. Continuous Transmit Options. a. Before the Continuous Transmit test, need to press “e” first The command will load the calibrate data to the EEROM, then the card can transmit the target power b. The channel frequency, data rate and output power could be changed in continuous transmit options. Press “c” to increase the output power , 11g Power (data rate 6Mbps) is 17dBm, 11b Power is 17dBm , Press ESC to return to the main Test Options menu when finished. 3. Continuous Receive Options Continuous receive options will put the radio into receive mode to allow for radio measurements. Press ESC to return to the main Test Options menu when
finished. 1.0 Scope 1.1 Document This document is to specify the product requirements for 802.11n Mini PCI. This mPCI is based on Atheros chip that complied with IEEE 802.11n from 2.4~2.5GHz, and it is also backward compatible to comply with IEEE 802.11g and IEEE 802.11b standard to connect your exist 802.11 b/g wireless LAN device. 1.2 Product Features  Compatible with IEEE 802.11g high rate standard to provide wireless 54Mbps data rate  Compatible with IEEE 802.11b high rate standard to provide wireless 11Mbps data rate  Compatible with IEEE 802.11n draft standard to provide wireless 300Mbps data rate  Operation at 2.4 ~ 2.5GHz frequency band to meet worldwide regulations  Dynamic date rate scaling at 6, 9, 12, 18, 24, 36, 48, 54Mbps for IEEE 802.11g  Dynamic date rate scaling at 1, 2, 5.5, and 11Mbps for IEEE 802.11b  Dynamic date rate of IEEE 802.11n scaling from MCS – 0 to MCS –15 as shown in Appendix I  Supports WEP, 802.1x, WPA and WPA2 enhanced security  Friendly user configuration and diagnostic utilities  Support Linux driver.  Supports Mini-PCI Type IIIA form factor 2.0 Requirements The following sections identify the detailed requirements of the 802.11 b/g/n
2.1 General Requirements 2.1.1 General Section # Feature Detailed Description 2.1.1.1 Antenna Type  Two UFL antenna connectorss 2.1.1.2 Operating Voltage  3.3VDC +/- 10% 2.1.14 Form Factor and Interface  Mini-PCI type III A form factor 2.2 Requirements of Reliability, Maintainability and Quality # Feature Detailed Description 2.2.1 MTBF  Mean Time Between Failure > 30,000 hours 2.22 Maintainability  There is no scheduled preventive maintenance required 2.2.3 Quality  The product quality is followed-up by Alpha Networks factory quality control system 2.3 Environmental Requirements # Feature Detailed Description 2.3.1 Operating Temperature Conditions  The product is capable of continuous reliable operation when operating in ambient temperature of 0 ℃ to +40℃. 2.3.2 Non-Operating Temperature Conditions  Neither subassemblies is damaged nor the operational performance is degraded when restored to the operating temperature after exposing to storage temperature in the range of –20 ℃ to +75 ℃. 2.3.3 Operating Humidity conditions  The product is capable of continuous reliable operation when subjected to relative humidity in the range of 10% and 90% non-condensing. 2.34 Non-Operating Humidity Conditions  The product is not damaged nor the performance is degraded after exposure to relative humidity ranging from 5% to 95% non-condensing
FederalCommunicationCommissionInterferenceStatementThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneofthefollowingmeasures:‐ Reorientorrelocatethereceivingantenna.‐ Increasetheseparationbetweentheequipmentandreceiver.‐ Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.‐ Consultthedealeroranexperiencedradio/TVtechnicianforhelp.ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.FCCCaution:Anychangesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser'sauthoritytooperatethisequipment.IMPORTANTNOTE:FCCRadiationExposureStatement:ThisequipmentcomplieswithFCCradiationexposurelimitssetforthforanuncontrolledenvironment.Thisequipmentshouldbeinstalledandoperatedwithminimumdistance20cmbetweentheradiator&yourbody.Thistransmittermustnotbeco‐locatedoroperatinginconjunctionwithanyotherantennaortransmitter.IEEE802.11bor802.11goperationofthisproductintheU.S.A.isfirmware‐limitedtochannels1through11.ThisdeviceisintendedonlyforOEMintegratorsunderthefollowingconditions:1) Theantennamustbeinstalledsuchthat20cmismaintainedbetweentheantennaandusers,and2) Thetransmittermodulemaynotbeco‐locatedwithanyothertransmitterorantenna,3) ForallproductsmarketinUS,OEMhastolimittheoperationchannelsinCH1toCH11for2.4Gbandbysuppliedfirmwareprogrammingtool.OEMshallnotsupplyanytoolorinfototheend‐userregardingtoRegulatoryDomainchange.Aslongas3conditionsabovearemet,furthertransmittertestwillnotberequired.However,theOEMintegratorisstillresponsiblefortestingtheirend‐productforanyadditionalcompliancerequirementsrequiredwiththismoduleinstalled(forexample,digitaldeviceemissions,PCperipheralrequirements,etc.).
IMPORTANTNOTE:Intheeventthattheseconditionscannotbemet(forexamplecertainlaptopconfigurationsorco‐locationwithanothertransmitter),thentheFCCauthorizationisnolongerconsideredvalidandtheFCCIDcannotbeusedonthefinalproduct.Inthesecircumstances,theOEMintegratorwillberesponsibleforre‐evaluatingtheendproduct(includingthetransmitter)andobtainingaseparateFCCauthorization.EndProductLabelingThistransmittermoduleisauthorizedonlyforuseindevicewheretheantennamaybeinstalledsuchthat20cmmaybemaintainedbetweentheantennaandusers.Thefinalendproductmustbelabeledinavisibleareawiththefollowing:“ContainsFCCID: RRKWMPN09HB1”.ManualInformationTotheEndUserTheOEMintegratorhastobeawarenottoprovideinformationtotheenduserregardinghowtoinstallorremovethisRFmoduleintheuser’smanualoftheendproductwhichintegratesthismodule.Theendusermanualshallincludeallrequiredregulatoryinformation/warningasshowinthismanual.
Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device This device has been designed to operate with an antenna having a maximum gain of 3.1dBi (Peak Gain) Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This radio transmitter IC 4833A- WMPN09HB1 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Approved antenna list: Impedance 50 ohm.  This device is intended only for OEM integrators under the following conditions: The transmitter module may not be co-located with any other transmitter or antenna. This device is intended only for OEM integrators under the following conditions: 1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2. The transmitter module may not be co-located with any other transmitter or antenna, 3. For all products market in CANADA, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: “Contains TX IC : 4833A- WMPN09HB1”. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. (Le manuel d'utilisation de dispositifs émetteurs équipés d'antennes amovibles doit contenir les informations suivantes dans un endroit bien en vue:) Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de dB [3.1]. Une antenne à gain plus élevé est strictement interdite par les règlements d'Industrie Canada. L'impédance d'antenne requise est de 50 ohms.
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne, 3) Pour tous les produits vendus au Canada, OEM doit limiter les fréquences de fonctionnement CH1 à CH11 pour bandes de fréquences 2.4G grâce aux outils de microprogrammation fournis. OEM ne doit pas fournir d'outil ou d'informations à l'utilisateur final en ce qui concerne le changement de réglementation de domaine. NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 4833A- WMPN09HB1". Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pourl'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectriqueà l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire àl'établissement d'une communication satisfaisante 以下警語適用台灣地區 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 本模組於取得認證後將依規定於模組本體標示審合格籤，並要求平台上標示「本產品內含射頻模組：ID編號」

Navigation menu