Alpha Networks WUSN10B1 USB wifi module User Manual WUS N10

Alpha Networks Inc. USB wifi module WUS N10

User Manual

Download: Alpha Networks WUSN10B1 USB wifi module User Manual WUS N10
Mirror Download [FCC.gov]Alpha Networks WUSN10B1 USB wifi module User Manual WUS N10
Document ID1607546
Application IDhMh8cvagiF/jvSP6sDvRew==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize2.17kB (27080 bits)
Date Submitted2011-12-21 00:00:00
Date Available2011-12-21 00:00:00
Creation Date2011-12-16 19:10:55
Producing SoftwareAcrobat Distiller 8.1.0 (Windows)
Document Lastmod2011-12-20 09:57:22
Document TitleMicrosoft Word - WUS-N10_User manual
Document CreatorPScript5.dll Version 5.2
Document Author: sam

ALPHA
WUS-N10
USB wifi module
User’s Manual
Release 0.1
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20
cm may be maintained between the antenna and users. The final end product must be labeled in a visible
area with the following: “Contains FCC ID: RRKWUSN10B1 ”. The grantee's FCC ID can be used only when
all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Introduction
The WUS-N10 which is based on the RT3070, is a 802.11 b/g/n wireless embedded Mini-PCI module for
AP/ Router + AP. WUS-N10 will be a RF module of AP board. It has greater throughput at longer range. The
WUS-N10 is a green product.
Features
Compatible with IEEE 802.11n draft 2.0 standard to provide up to 150Mbps data rate.
Compatible with IEEE 802.11g standard to provide up to wireless 54Mbps data rate
Compatible with IEEE 802.11b standard to provide up to wireless 11Mbps data rate
Operation at 2.4 ~ 2.5GHz frequency band to meet worldwide regulations
Dynamic date rate scaling at 6, 9, 12, 18, 24, 36, 48, 54 for IEEE 802.11g.
Dynamic date rate scaling at 1, 2, 5.5, and 11Mbps for IEEE 802.11b
Maximum reliability, throughput and connectivity with automatic data rate switching
Support wireless data encryption with 64/128-bit WEP for security
Support infrastructure networks via Access Point and ad-hoc network via peer-to-peer communication
Support WEP, 802.1x, WPA and WPA2 enhanced security
Friendly user configuration and utilities
Drivers support Windows 2K, XP 32/64-bit, Vista 32/ 64-bit, MAC OS and Linux
Support external WPS button to connect Access Point easily
High speed USB 2.0 interface
RoHS compliant
Integrated antenna
Support Xlink global networking gaming
Interoperability, driver backward compatibility
Installation
Turn on the computer and Insert the Alpha WUS-N10 Driver CD in the CD-ROM drive
When the auto run screen appears, click Install Drivers.
The Install Shield Wizard window will appear.
By default setup will install to the default location: To install to a different location click Browse and
specify the location.
Select the Program Files folder location
Insert the adapter into an available USB port on your computer.
The Wireless Connection Wizard will now appear.
To connect to your network using the WPS push button configuration method, click the virtual button
as shown in the screenshot.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : 3.1-701
Format                          : application/pdf
Creator                         : sam
Title                           : Microsoft Word - WUS-N10_User manual
Create Date                     : 2011:12:16 19:10:55+08:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2011:12:20 09:57:22+08:00
Metadata Date                   : 2011:12:20 09:57:22+08:00
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:af7e4639-54f9-4f44-9a8f-6dabd09347d8
Instance ID                     : uuid:874ff8e9-d4fa-46bc-9080-230e87324277
Page Count                      : 5
Author                          : sam
EXIF Metadata provided by EXIF.tools
FCC ID Filing: RRKWUSN10B1

Navigation menu