Alpha Networks WUSN19DA1 USB Module User Manual WUS N19D User s manual REV
Alpha Networks Inc. USB Module WUS N19D User s manual REV
User Manual.pdf
User’s Manual For USB Module Model Number : WUS-N19D Revision: 1.0 Alpha Networks Proprietary and Confidential Information Test Utility Installation: Hardware: BCM43235 RGMII INIC test fixture, with gigabit Ethernet port computer Software: RT3x5x MII V1.0.1.0 1. Insert WUS-N19D to BCM43235 RGMII INIC test fixture, connect the test fixture to computer with Ethernet cable 2. Use RT3x5x MII V1.0.1.0, make sure the computer has installed the wincap.exe 3. Select GIGABIT INIC 4. Use QA tool control WUS-N19D Alpha Networks Proprietary and Confidential Information 1.1 Document This document is to specify the product requirements for USB Module. This iNIC Card is based on BCM43235 single chipset that complied with complied with IEEE 802.11n Draft 2.0, IEEE 802.11 b/g standard from 2.4~2.5GHz. It can be used to provide up to 54Mbps for IEEE 802.11g , 11Mbps for IEEE 802.11b and 300Mbps for IEEE 802.11n to connect your wireless LAN. 1.2 Product Features BCM43235 , single chip , 2T2R , MA/BBP/RF A WLAN intelligent NIC solution to a host SOC platform High performance 384 MHz MIPS24Kec CPU inside to Ethernet PHY and Gigabit Ethernet MAC 300Mbps PHY data rate for longer range and better throughput Compatible with IEEE 802.11g high rate standard to provide wireless 54Mbps data rate Compatible with IEEE 802.11b high rate standard to provide wireless 11Mbps data rate Compatible with IEEE 802.11n draft standard to provide wireless 300Mbps data rate Operation at 2.4 ~ 2.5GHz frequency band to meet worldwide regulations Dynamic date rate scaling at 6, 9, 12, 18, 24, 36, 48, 54Mbps for IEEE 802.11a and IEEE 802.11g Dynamic date rate scaling at 1, 2, 5.5, and 11Mbps for IEEE 802.11b Dynamic date rate of IEEE 802.11n scaling from MCS – 0 to MCS –15 as shown in Appendix I Supports wireless data encryption with 64/128 bit WEP for security Support WPA and WPA2 enhanced security Support QoS – WMM , WMM power save Support RGMii signals transmission Drivers support Linux 2.6 Alpha Networks Proprietary and Confidential Information 2.0 Requirements The following sections identify the detailed requirements of the USB Module . 2.2 General Requirements 2.2.1 IEEE 802.11b Section Feature Detailed Description 2.2.2.1 2.2.2.2 Standard Radio and Modulation Schemes Operating Frequency Channel Numbers IEEE 802.11b DQPSK, DBPSK, DSSS, and CCK 2400 ~ 2483.5MHz ISM band Data Rate Media Access Protocol Transmitter Output Power 11 channels for United States/ TAIWAN 13 channels for Europe Countries 14 channels for Japan 11, 5.5, 2, and 1Mbps CSMA/CA with ACK 2.2.2.3 2.2.2.4 2.2.2.5 2.2.2.6 2.2.2.7 2.2.2.8 Receiver Sensitivity Typical RF Output Power (Tolerance +-2dB) at each RF chain, Data Rate and at room Temp. 25degree C 18±2dBm at 1,2,5.5,11Mbps Typical Sensitivity at Which Frame (1000-byte PDUs) Error Rate = 8% –88 dBm at 1Mbps –88 dBm at 2Mbps –88 dBm at 5.5Mbps –86 dBm for 11Mbps 2.2.2 IEEE 802.11g Section Feature Detailed Description 2.2.3.1 2.2.3.2 Standard Radio and Modulation Type Operating Frequency Channel Numbers IEEE 802.11g BPSK, QPSK, 16QAM, 64QAM with OFDM Data Rate Media Access Protocol Transmitter Output Power 2400 ~ 2483.5MHz ISM band 11 channels for United States/ TAIWAN 13 channels for Europe Countries 13 channels for Japan 6,9,12,18,24,36,48,54Mbps CSMA/CA with ACK 2.2.3.3 2.2.3.4 2.2.3.5 2.2.3.6 2.2.3.7 2.2.3.8 Receiver Sensitivity Typical RF Output Power (tolerance +-2dB) at each RF chain, Data Rate and at room Temp. 25degree C 18±2dBm at 6~18 Mbps 17±2dBm at 36 and 24Mbps 15±2dBm at 54 and 48 Mbps Typical Sensitivity at Which Frame (1000-byte PDUs) Error Rate = 10% –87 dBm at 6Mbps Alpha Networks Proprietary and Confidential Information # Feature Detailed Description –86 dBm at 9Mbps –84 dBm at 12Mbps –82 dBm at 18Mbps –79 dBm at 24Mbps –75 dBm at 36Mbps –71 dBm at 48Mbps –70 dBm at 54Mbps 2.2.3 IEEE 802.11n Section for 2.4G Band Feature Detailed Description 2.2.4.1 2.2.4.2 Standard Radio and Modulation Type Operating Frequency Data Rate Media Access Protocol Transmitter Output Power IEEE 802.11n BPSK, QPSK, 16QAM, 64QAM with OFDM 2400 ~ 2483.5MHz ISM band From MCS – 0 to MCS –15 as shown in Appendix I CSMA/CA with ACK 2.2.4.3 2.2.4.4 2.2.4.5 2.2.4.6 2.2.4.7 Typical RF Output Power (tolerance +-2dB) at each RF chain, Data Rate and at room Temp. 25degree C HT 20 17±2 dBm at MCS 0,1 17±2 dBm at MCS 2,3 16±2 dBm at MCS 4,5 14±2 dBm at MCS 6,7 HT 40 15±2 dBm at MCS 0,1 15±2 dBm at MCS 2,3 14±2 dBm at MCS 4,5 12±2 dBm at MCS 6,7 Typical Sensitivity at Which Frame (1000-byte PDUs) Error Rate = 10% Receiver Sensitivity HT20 –85 dBm at MCS 0 –82 dBm at MCS 1 –80 dBm at MCS 2 –77 dBm at MCS 3 –74 dBm at MCS 4 –70 dBm at MCS 5 –68 dBm at MCS 6 –66 dBm at MCS 7 HT40 –82 dBm at MCS 0 –79 dBm at MCS 1 –77 dBm at MCS 2 –74 dBm at MCS 3 –71 dBm at MCS 4 –67 dBm at MCS 5 –65 dBm at MCS 6 –63 dBm at MCS 7 2.3 General Section Feature Detailed Description 2.3.1.1 Antenna Connector Three UFL antenna connectors Alpha Networks Proprietary and Confidential Information 2.3.1.2 2.31.3 2.3.1.4 2.3.1.5 Operating Voltage Current Consumption Form Factor and Interface LED 3.3VDC +/- 10% 450 mA at continuous transmit mode (2 Tx chains on ) 250 mA at continuous receive mode (2 Rx chains on ) USB form factor External LED function supported 2.4 Software Requirements The Configuration Software supports Linux2.6. This configuration software includes the following functions: Information Information allows you to monitor network status. Configuration Configuration allows you to configure parameters for wireless networking. Security Supports enhanced security WEP, 802.1x, WPA and WPA2. 2.4.1 Information Feature Detailed Description 2.4.1.1 General Information 2.4.1.2 Current Link Information 2.4.1.3 Site survey General Information shows the name of Wireless Adapter, Adapter MAC Address, Regulatory Domain, Firmware Version, and Utility Version. Current Link Information shows the Current Setting ESSID, Channel Number, Associated BSSID, Network Type, Security Status, Link Status, Transmit Speed, Signal Strength, and Link Quality. To search the neighboring access points and display the information of all access points. 2.4.2 Configuration Feature Detailed Description 2.4.2.1 ESS ID 2.4.2.2 Network Type Input an SSID number if the roaming feature is enabled Supports for ASCII printable characters. Ad-hoc Mode and 802.11 Ad-hoc Mode for network configurations that do not have any access points Infrastructure Mode for network configurations with access points Extend the battery life of clients by allowing the client to sleep for short periods of time while the Access Point buffers the messages. Set the number of bytes used for fragmentation boundary for messages Set the number of bytes used for RTS/CTS boundary 2.4.2.3 Power Save 2.4.2.4 RTS Threshold 2.4.2.5 2.4.2.6 Fragment Threshold Transmission Speed 2.4.2.7 Roaming Feature Detailed Description 2.4.3.1 Encryption This indicates the communication rates. Select appropriate transmission speed to match your wireless LAN settings Support Automatic or Manual Rescan to associate with access point. 2.4.3 Security RC4 encryption algorithm Support 64-bit and 128-bit WEP encryption Alpha Networks Proprietary and Confidential Information # Feature Detailed Description 2.4.3.2 WEP Management 2.4.3.3 2.4.3.4 802.1x WPA/WPA2 Support open system (OSA) and shared key authentication (SKA) Four WEP keys can be selected STA with WEP off will never associate any AP with WEP enabled WEP Key Format: Option for Hex format Support EAP-TLS, EAP-TTLS, and EAP-PEAP Support WPA/WPA2-PSK and WPA/WPA2-EAP Support Cipher Mode AES and TKIP 2.5 Mechanical Requirements Feature Detailed Description 2.5.1 2.5.2 2.5.3 Length Width Height 72mm(max) 48mm (+-0.25) 4.7mm (+-0.1) 2.6 Compatibility Requirements This device passes the following compatibility requirements. Feature Detailed Description 2.6.1 2.6.2 2.6.3 Wi-Fi WHQL Physical Layer and Functionality Meet Wi-Fi certification for IEEE 802.11b/g/n product Meet applicable WHQL certification requirements Meet ALPHA Engineering Test Plan and Test Report 2.7 Requirements of Reliability, Maintainability and Quality Feature Detailed Description 2.7.1 2.7.2 2.7.3 MTBF Maintainability Quality Mean Time Between Failure > 30,000 hours There is no scheduled preventive maintenance required The product quality is followed-up by ALPHA factory quality control system 2.8 Environmental Requirements Feature Detailed Description 2.8.1 Operating Temperature Conditions Non-Operating Temperature Conditions The product is capable of continuous reliable operation when operating in ambient temperature of 0℃ to +40℃. Operating Humidity conditions Non-Operating Humidity Conditions Neither subassemblies is damaged nor the operational performance is degraded when restored to the operating temperature after exposing to storage temperature in the range of -40 ℃ to +70℃. The product is capable of continuous reliable operation when subjected to relative humidity in the range of 10% and 90% non-condensing. The product is not damaged nor the performance is degraded after exposure to relative humidity ranging from 5% to 95% non-condensing 2.8.2 2.8.3 2.8.4 Alpha Networks Proprietary and Confidential Information Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Alpha Networks Proprietary and Confidential Information This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: RRKWUSN19DA1”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Alpha Networks Proprietary and Confidential Information
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract XMP Toolkit : 3.1-701 Format : application/pdf Title : Microsoft Word - WUS-N19D_User's manual-REV Creator : eden Create Date : 2012:10:03 16:30:25+08:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2012:10:04 11:20:15+08:00 Metadata Date : 2012:10:04 11:20:15+08:00 Producer : Acrobat Distiller 8.1.0 (Windows) Document ID : uuid:44b9bda3-f768-4833-9a00-b33c97cf4265 Instance ID : uuid:0c9d0546-8dc5-42ae-a032-d44987e096c9 Page Count : 9 Author : edenEXIF Metadata provided by EXIF.tools