Amcrest Technologies BC911M14 Pan/Tilt Video Baby Monitor (Monitor Unit) User Manual 01

Amcrest Technologies LLC Pan/Tilt Video Baby Monitor (Monitor Unit) 01

Contents

User manual part2

SetupCamera SetupPower Supply - Using AC Power1.1211. Plug one end of the provided power adapter into a wall outlet and the other end into the back of the camera.2. Press the ON/OFF button to turn on the camera. The LED (green light) on the camera will light up.Note : Press and hold the ON/OFF button for about 2 seconds to turn off the camera.1. Open the battery compartment cover on the rear of the monitor.2. Insert the battery with the metal facing the battery compartment.3. Close the battery compartment cover, and make sure it is locked securely.4. Press the POWER button to turn on the monitor.Monitor SetupPower Supply2.12The monitor uses a Lithium-ion rechargeable battery, or the household poweradapter.Loading the BatteryWhen Battery is in low level after loading the battery, the LED (greed light) will start blinking and need to recharging.1. Plug one end of the provided power adapter into a wall outlet and the other end into the monitor.2. The LED (red light) will light up when the battery is charging . 3. When battery is fully charged, the LED (red light) will turn off .Battery ChargingNight Vision1.2The camera has eight high-intensity LEDs for picking up clear images in the dark.When the light sensor detects low ambient light levels, the LEDs will be automaticallyactivated. Press the brightness up button and down button at the same time onthe monitor unit to enable/disable/auto the night vision function.The on-screen-display (OSD) will notify you the night vision function is set toON/OFF/AUTO. 1. Plug one end of the provided power adapter into a wall outlet and the other end into the monitor.2. Press the POWER button and to turn on the monitor.Note 1 : When power on the monitor, the LED (green light) will light up.Note 2 : Press and hold the POWER button for about 2 seconds to turn off the monitor.Using AC Power
3Monitor Remote Control Function2.2The monitor can control the movement of the camera. The camera head has theability to rotate up, down, right and left. Press the up or down buttonson monitor to move the camera up or down. Press the left or right buttonson monitor to move the camera left or to the right. See Fig. 3.Fig. 3PanTiltVOX ( Voice-Operated Transmission) function2.31. Press the volume up button and down button at the same time on the monitor unit to enable/disable the VOX function. The on-screen-display (OSD) will notify you if the VOX function is enabled or disabled.2. When VOX function is enabled, the camera will detect the sound level. If there is very low sound in the vicinity of the camera for 180 seconds continuously, the screen and speaker of monitor will turn OFF.3. When the camera dectects sound, the screen and speaker of the monitor will turn ON.
4Volume Setting2.4Press volume up or down buttons to adjust volume level.Press to increase volume.Press to decrease volume.The system comes with a camera unit that has already been paired with themonitor. The "Camera Paring" function gives each camera unit a separatechannel on the monitor unit. This is necessary for configuring additionalcamera units.If you want to add a new camera, please follow the below steps:1. Make sure both the monitor unit and camera units are off.2. Press and hold the “P” button on monitor unit and press button.3. You will reach the below pairing screen:4. Turn on the camera unit5. Press pairing button on the camera unit, you will see the below screen when pairing is successful.6. Press button to start monitoring. Brightness Setting (Brightness)2.5Press brightness up or down buttons to adjust the brightness.Press to increase brightness.Press to decrease brightness.Press the “P” button on monitor unit to switch between different cameras.The camera number (Cam #) will be shown on the top left corner of the screen.Camera ParingCamera Selection3.13Amcrest Camera Pairing SystemWaiting signal from CAM1 ...Press ‘PAIRING’ of Camera Unit to pairPress ‘P‘ to skip and pair the next CAM IDPress power button to abort and turn offAmcrest Camera Pairing SystemWaiting signal from CAM1 ...OKWaiting signal from CAM2Press ‘PAIRING’ of Camera Unit to pairPress ‘P‘ to skip and pair the next CAM IDPress power button to abort and turn off
5Package Contents- One Camera- One Monitor- Two Power Adapters- Lithium-ion Battery for Monitor- User ManualCare and Maintenance- Keep all parts and accessories out of children's reach.- Fingerprints or dirt on the lens surface can adversely affect camera performances. Avoid touching the lens surface with your fingers.- Should the lens become dirty, use a soft, dry cloth to wipe off the lens.- Keep the system dry. Precipitation, humidity, and other liquids contain minerals that will corrode electronic circuits.- Do not use or store in dusty, dirty areas.- Do not use or store in hot areas. High temperatures can shorten the life of electronic devices and warp or melt certain plastics.- Do not user of store in very cold areas. When the system warms up (to its normal temperature), moisture can form inside the case, which may damage electronic circuit boards.- Do not attempt to open the case. Non-expert handling of the device may damage the system.- Avoid dropping or strong shocks.- Operate this product using only with the power supply included or provided accessory.- Do not overload electrical outlets or extension cords. This can result in fire or electric shocks.- Do remember that you are using public airwaves when you use the system and that sound and video may be broadcast to other 2.4 GHz receiving devices. Conversations, even from rooms near the camera, may be broadcast.To protect the privacy of your home, always turn the camera off when not in use.- Keep the system in proper ventilation when it is operating. Do not use the system in bed, and do not cover the system with cloth, pillow, bag, towel and blanket.TroubleshootingYou don’t getting any signal- Make sure the camera and the monitor are turned on.- Make sure the power plugs are firmly installed and plugged in.If the signal is poor, or if there is interference- If there is a microwave oven use in the between the camera and monitor, remove the microwave oven or turn it off, it may be causing interference.- Try to put the camera and the monitor closer together if possible, or adjust the antenna angle if residing in a multi-story building.
6FCC StatementWARNING : Modifications not authorized by the manufacturer may void users authority to operate this device.This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interferencethat may cause undesired operation. Changes or modifications not expresslyapproved by the party responsible for compliance could void the user’s authorityto operate the equipment.This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses, and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more offollowing measures:Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.- Consult the dealer or an experienced radio / TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interferencethat may cause undesired operation.Caution- To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.FCC ID : ZZ2BC911M14 FCC ID : ZZ2BC911C14
7Following the safety tipsTo prevent deaths and injuries associated with baby monitor cords :- Make sure the camera unit and power adapter cable are always out of reach of the baby at least 3 feet (1 meter) away. Note : It's important even if your baby is not yet standing or mobile.- Never use extension cords with power adapters. Only use the power adapters provided.SpecificationsCamera UnitSpecifications subject to change without noticeThis item is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.CameraFrequencyAntennaTransmission distanceModulationImage SensorLensIR LEDDimensionsWeightPowerOperating temperature2.4 GHzDipole antenna800 feet (Line of Sight)FHSSCMOS image sensorf 2.95mm, F/1.88 pcs10.8(W) x 9.0(H) x 11.8(D) cm120gDC 6V, 800mA0℃ ~ 40℃ (32℉ ~ 104℉)MonitorFrequencyAntennaModulationDisplayDisplay colorsBrightness ControlVOXDimensionsWeightPowerOperating temperature2.4 GHzDipole antennaFHSS2.4" LCD panelFull-color6 levelsVoice activation7.8(W) x 17.7(H) x 3.0(D) cm90gDC 6V, 800mA or Li battery0℃ ~ 40℃ (32℉ ~ 104℉)
8Power Adapter information Battery informationSource 1Model numberInputOutputS08-006-0060-00800100 ~240 , 50 ~60 Hz, 0.2A6V 800mASource 2Model numberInputOutput CS6D060080100 ~240 , 50 ~60 Hz, 0.2A6V 800mAModel numberSpecification PT6034503.7V 1000mAhCAUTION :Risk of explosion If battery is replaced by an incorrect type. Dispose of used battery according to the instructions. Only use Power Adapter listed in the user manual. Only use Battery listed in the user manual.V4

Navigation menu