Amcrest Technologies WLD895 2.4GHz Digital RF Module User Manual Go Link

Download:
Mirror Download [FCC.gov]
Document ID	2564692
Application ID	mbHVGQpooSTvFVkCDDa/Jg==
Document Description	User Manual rev.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	14.76kB (184500 bits)
Date Submitted	2015-03-24 00:00:00
Date Available	2015-06-30 00:00:00
Creation Date	2015-03-17 13:24:15
Producing Software	Acrobat Distiller 10.1.10 (Windows)
Document Lastmod	2015-03-24 13:35:47
Document Title	Go-Link
Document Creator	Acrobat PDFMaker 10.1 Word 版
Document Author:	Monica Fan

Amcrest Technologies LLC
WLD895
2.4GHz Digital RF Module
Date: 2015/3/17
A. Features
Operating frequency range from 2400 to 2483.5 MHz
Maximum data rate 4 Mbps (GFSK)
Support 3-wire or 4-wire SPI.
Modulation scheme : FSK/GFSK
Power supply range: 3 ~ 3.6V
Transmission range: 250 m (Line of sight)
Outline: 26.16x 18.36 x 3.75 m
Host equipment power supply: DC 9V
B. Applications
Digital Baby Monitor
Wireless Video Door phone
Security Camera
Preliminary data subjects to change without notice
Amcrest Technologies LLC
WLD895
2.4GHz Digital RF Module
Date: 2015/3/17
C: Specification
Parameter
Min.
Typ.
Max.
Unit
3.3
3.6
Electrical Section
Supply Voltage
Supply current in TX mode
TBD
mA
Supply current in RX mode
TBD
mA
Crystal
16M
Hz
Modulation Mode
FSK/GFSK
RF Section
Operating Frequency(Note1)
2400
Data Rate
2483.5
MHz
4M
bps
Transmission Power
+17
dBm
Power control range
0~19
dB
dBm
Transmitter Section
Receiver Section
Sensitivity
-85
-88
Operating Temperature
-20
+70
℃
Storage Temperature
-40
+85
℃
Operation
Note: 1. 2.4GHz ISM Band
Preliminary data subjects to change without notice
Amcrest Technologies LLC
WLD895
2.4GHz Digital RF Module
Date: 2015/3/17
D: Pin Assignment
No.
Marks
Function
VCC
Power Supply
CKO
CKO pin output
GPIO2
GPIO2/4-wire SPI data out
GPIO1
GPIO1/4-wire SPI data out
SDA
SPI Data I/O
SCK
SPI Clock
SCS
SPI Chip select
TX_SW
RF front end TX switch
RX_SW
RF front end RX switch
10
GND
Ground
RF Front End Control:
Preliminary data subjects to change without notice
Amcrest Technologies LLC
WLD895
2.4GHz Digital RF Module
Date: 2015/3/17
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Preliminary data subjects to change without notice
Amcrest Technologies LLC
WLD895
2.4GHz Digital RF Module
Date: 2015/3/17
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such
that 20 cm may be maintained between the antenna and users. The final end product must be labeled in
a visible area with the following: “Contains FCC ID: ZZ2WLD895”. The grantee's FCC ID can be used
only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install
or remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Preliminary data subjects to change without notice

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Copy, Extract
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2015:03:17 13:24:15+08:00
Creator Tool                    : Acrobat PDFMaker 10.1 Word 版
Modify Date                     : 2015:03:24 13:35:47+08:00
Metadata Date                   : 2015:03:24 13:35:47+08:00
Producer                        : Acrobat Distiller 10.1.10 (Windows)
Keywords                        : 
Format                          : application/pdf
Creator                         : Monica Fan
Title                           : Go-Link
Description                     : Specification
Document ID                     : uuid:85cc8207-41ff-4c00-a4d3-758b8bc79019
Instance ID                     : uuid:19464335-1649-4035-8a44-c8c35842faae
Subject                         : 5
Company                         : Go-LInk
Category                        : module
Source Modified                 : D:20150317052412
Headline                        : Specification
Page Count                      : 5
Page Layout                     : OneColumn
Author                          : Monica Fan

EXIF Metadata provided by EXIF.tools