American Standard Amarilis Heritage Kitchen Faucet 8280 Users Manual M34450B HERT BTM MT
2015-02-02
: American-Standard American-Standard-Amarilis-Heritage-Kitchen-Faucet-8280-Users-Manual-415699 american-standard-amarilis-heritage-kitchen-faucet-8280-users-manual-415699 american-standard pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Installation Instructions BOTTOM-MOUNTED KITCHEN FAUCETS 7230 7231 7270 7271 SERIES SERIES SERIES SERIES 8280 SERIES 8281 SERIES Certified to comply with ANSI A112.18.1M U.S. Patent No. 5,819,789 To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. M34450B SPOUT SUBASSEMBLY AERATOR ESCUTCHEON RUBBER RING HANDLE SCREW RUBBER WASHER 7230 SERIES GOOSENECK SPOUT CARTRIDGE BRASS WASHER CARTRIDGE SEAL LOCKNUT ESCUTCHEON DIVERTER O-RINGS RUBBER RING RUBBER WASHER 7270 SERIES D-TUBE SPOUT SPRAY HEAD BRASS WASHER LOCKNUT VALVE HOUSING PLUG SPRAY HOLDER TUBE COUPLING NUT O-RING PLASTIC LOCKNUT NIPPLE 8280 SERIES HI-FLOW SPOUT WRENCH SPRAY HOSE Printed in Mexico 1 2 CAUTION HAND SPRAY INSTALLATION Turn off hot and cold water supplies before beginning. FOR MODEL 7231 AND 7271 ONLY: VALVE INSTALLATION Remove ESCUTCHEONS with RUBBER RINGS and insert VALVE HOUSING through holes from underside of SINK. Thread of all three VALVE SHANKS should extend at least 5/16 inch above SINK top. If necessary, adjust LOCKNUTS. Place RUBBER RINGS into ESCUTCHEONS' recess and thread ESCUTCHEONS onto VALVE HOUSING until snug against internal stop. Center VALVE HOUSING on SINK and tighten LOCKNUTS (3) using WRENCH supplied with faucet. Connect the HOT water supply to the left valve and the COLD water supply to the right valve using sealant, appropriate connectors, and COUPLING NUTS. ESCUTCHEON HANDLE SCREW SPRAY HEAD Place SPRAY HOLDER into separate hole of SINK. Assemble PLASTIC LOCKNUT onto SHANK of SPRAY HOLDER and tighten. RUBBER WASHER Feed SPRAY HOSE through SPRAY HOLDER and attach COUPLING NUT of HOSE to NIPPLE of VALVE CENTER. Tighten COUPLING NUT firmly. SPRAY HOLDER SPACER WASHER NUT VALVE CENTER SINK Make certain that SPACER WASHER and RUBBER WASHER are attached to SPRAY HOSE and thread SPRAY HEAD to NUT. RUBBER RING 5/16'' MIN. SINK PLASTIC LOCKNUT NIPPLE RUBBER WASHER COUPLING NUT BRASS WASHER LOCKNUT SPRAY HOSE VALVE BODY 3 SPOUT INSTALLATION Check that both O-RINGS are properly seated on the valve center. FOR MODELS WITH HAND SPRAY: Check that the DIVERTER PLUG is free and can move up and down. SPOUT NUT SPOUT SUBASSEMBLY Apply the grease (provided) liberally to the O-RINGS. Push the SPOUT SUBASSEMBLY on to the VALVE CENTER and tighten the SPOUT NUT until snug on valve body. 4 TEST INSTALLED FAUCET Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks. Remove AERATOR. With handle in OFF position, turn on water supplies and check all connections for leaks. 5 DIVERTER PLUG O-RINGS SERVICE Turn handles into OFF position and replace AERATOR. If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°. To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Remove INSERT and HANDLE SCREW. SPRING Slip HANDLE with ADAPTER off. CLIP Remove SPRING CLIP. Lift STOP WASHER, turn 90° and replace. Replace SPRING CLIP. Replace ADAPTER, HANDLE, SCREW, and INSERT. STOP WASHER AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean. HOTLINE FOR HELP Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then: Remove INSERT and HANDLE SCREW. CARTRIDGE Slip HANDLE with ADAPTER off. Unscrew CARTRIDGE with wrench. Thoroughly rinse plastic SCREEN at base of CARTRIDGE. Replace CARTRIDGE until flange is tight against valve body. Turn valves OFF. SCREEN Replace ADAPTER, HANDLE, SCREW, and INSERT. For toll-free information and answers to your questions, call: 1 (800) 223-0068 Weekdays 8:00 a.m. to 4:00 p.m. Eastern Time Product names listed herein are trademarks of American Standard Inc. C American Standard Inc. 1999 M34450B
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:04:24 08:35:44 Producer : Acrobat Distiller 4.0 for Macintosh Creator : Adobe Illustrator¨ 8.0.1: LaserWriter 8 8.6 Author : Marianne Temesy Title : M34450B HERT KITCHEN BTM MT Modify Date : 2001:04:24 08:35:53-04:00 Page Count : 2EXIF Metadata provided by EXIF.tools