American Standard Champion 4 2018 Users Manual 730529 En

2585 to the manual 2ea2fe38-95aa-40a9-b6db-752edb539b66

2015-02-02

: American-Standard American-Standard-Champion-4-2018-Users-Manual-417618 american-standard-champion-4-2018-users-manual-417618 american-standard pdf

Open the PDF directly: View PDF .
Page Count: 5

SAVE FOR FUTURE USE

730529-100 Rev. U

Product names listed herein are trademarks of AS America, Inc.

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant

Hacksaw Wax Ring/Gasket Flexible Supply Tube 1/2" Deep Well Nut Driver or

Closet Bolts Tape Measure Carpenters Level Deep Well Socket Wrench

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly define contour of china and components.

Recommended fitting type for back-to-back installations.

Depending upon your plumbing and venting conditions, the flow from

the Champion in a back-to-back installation may create a vacuum on

the system and draw water from the opposing bowl. The National

Standards Plumbing Code prohibits the use of a cross fitting for

drainage as throw over is possible. The code does approve a

directional "Y" style fitting with proper venting to direct the water

downward and away from the other toilet.

NOTE: BACK-TO-BACK INSTALLATION

Doral Classic™ Champion® 4 2-piece Toilets

Models - 2058, 2074, 2076, 2473

Doral Classic™ Champion® 4 2-piece Toilets

Models - 2367, 2368, 2369, 2443

Oakmont™ Champion® 4 2-piece Toilets

Models - 2625, 2627, 2738

Townsend™ Champion® 4 2-piece Toilets

Models - 2733, 2735

Champion® 4 2-piece Toilets

Models - 2002, 2018, 2023, 2414, 2585,

2792, 2586, 2793, 3186, 3404

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this

product is installed properly, please read these instructions carefully before you begin. (Certain installations

may require professional help.) Also be sure your installation conforms to local codes.

REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE: Mounting surface must be clean and level before new toilet is installed!

CLOSET FLANGE

CLOSET BOLTS

WAX RING

SEALANT

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and install wax

ring evenly around waste flange, with tapered end of ring facing

toilet. Apply a thin bead of sealant around toilet base.

730529-100 Rev. U

- 2 -

FINISHED WALL

19mm ± 6mm

(1 ± 1/4")

419mm

(16-1/2")

FINISHED

FLOOR

305mm

(12")

772mm

(30-3/8")

83mm

(3-1/4")

470mm

(18-1/2")

16mm

(5/8")

SUPPLY

REQ'D

152mm

(6")

254mm

(10")

356mm

(14")

FINISHED WALL

19mm ± 6mm

(1 ± 1/4")

387mm

(15-1/4")

FINISHED

FLOOR

305mm

(12")

772mm

(30-3/8")

721mm

(28-3/8")

83mm

(3-1/4")

470mm

(18-1/2")

419mm

(16-1/2")

16mm

(5/8")

SUPPLY

REQ'D

152mm

(6")

254mm

(10")

356mm

(14")

721mm

(28-3/8")

419mm

(16-1/2")

* ROUND FRONT

MODELS

NOTE: DRAWINGS ARE FOR DIMENSIONAL PURPOSES ONLY. THEY ARE NOT EXACT REPRESENTATIONS.

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90°, and slide into

place 6" (152 mm) apart and parallel to wall.

ROUGHING-IN DIMENSIONS: Right Height™ Elongated Two Piece Toilet

Right Height™ Round Front Two Piece Toilet

ROUGHING-IN DIMENSIONS: Normal Height Elongated Two Piece Toilet

Normal Height Round Front Two Piece Toilet

MODEL

ABCDE F

DIMENSIONS

235mm (9-1/4) 264mm (10-3/8) 362mm (14-1/4) 464mm (18-1/4) 825mm (32-1/2) 254mm (10)

2018, 2023, 2585, 2792 235mm (9-1/4) 264mm (10-3/8) 362mm (14-1/4) 464mm (18-1/4) 797mm (31-3/8) 254mm (10)

2058 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 479mm (18-7/8) 873mm (34-3/8) 254mm (10)

2074, 2076 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 479mm (18-7/8) 851mm (33-1/2) 254mm (10)

2367 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 492mm (19-3/8) 872mm (34-5/16) 254mm (10)

2368, 2369 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 492mm (19-3/8) 844mm (33-1/4) 254mm (10)

2625, 2627 216mm (8-1/2) 273mm (10-3/4) 381mm (15) 492mm (19-3/8) 844mm (33-1/4) 286mm (11-1/4)

2738 216mm (8-1/2) 275mm (10-13/16) 384mm (15-1/8) 492mm (19-3/8) 872mm (34-5/16) 295mm (11-5/8)

2733, 2735 216mm (8-1/2) 267mm (10-1/2) 379mm (14-7/8) 479mm (18-7/8) 873mm (34-3/8) 284mm (11-3/16)

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet

on closet flange so bolts project through

mounting holes.

b. Loosely install retainer washers and nuts.

Side of washers marked "THIS SIDE UP"

must face up!

CLOSET

BOLT

NUT

TAPERED

WASHER

FLANGE

MANIFOLD INSIDE WATERWAY – DO NOT REMOVE

2002, 2414, 2586,

2793, 3186, 3404

730529-100 Rev. U

- 3 -

9a Before continuing, determine the type of water supply connection you have from the chart below and use the appropriate assembly parts

required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings.

CAUTION: DO NOT USE

CONE WASHER WITH

PLASTIC SUPPLY LINE.

CAUTION: Overtightening of

LOCK NUT or COUPLING NUT

could result in breakage and

potential flooding.

These parts must be used as illustrated

to insure water-tight connection. Use of

existing coupling nut may result in water

leakage. Water supply tube or pipe

must extend at least 1/2" inside

threaded shank of valve (does not apply

to flanged tubing).

Use existing

coupling nut

and washer.

Use existing spiral cone

washer. Fluidmaster

cone washer may not

seal completely on

spiral type supply line.

Captive cone

washers already

included. No

additional washers

needed.

METAL/COPPER

FLARED TUBING

METAL FLANGED

TUBING

METAL SPIRAL

TUBING

VINYL/BRAIDED

CONNECTOR

LOCK NUTLOCK NUT LOCK NUT LOCK NUT

COUPLING

NUT

COUPLING

NUT

EXISTING

COUPLING

NUT

COUPLING

NUT

WATER

SHUT-OFF

WATER

SHUT-OFF

WATER

SHUT-OFF

WATER

SHUT-OFF

CONE

WASHER

EXISTING

CONE

WASHER

EXISTING

WASHER

8INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.

!WARNING: Do not use plumber’s putty, pipe dope, or any other sealant on the water supply

connection to this tank. If the connection leaks after hand tightening, replace the supply line.

If the connection continues to leak with the new supply line, replace the fill valve.

Warranty is void if any type of sealant is used on the water supply connection.

INSTALL TOILET

a. Position toilet squarely to wall and, with a rocking motion,

press bowl down fully on wax ring and flange. Alternately

tighten nuts until toilet is firmly seated on floor.

CAUTION:

DO NOT OVERTIGHTEN NUTS

OR BASE MAY BE DAMAGED!

b. Install caps on washers.

(If necessary, cut bolt height to size before installing caps.)

c. Smooth off the bead of sealant around base.

Remove excess sealant.

CLOSET BOLT

NUT

WASHER

BOLT CAP

INSTALL TANK

Recommended tool: Deep socket tool included in tank kit.

a. Install large rubber gasket over threaded outlet on bottom of tank and

lower tank onto bowl so that tapered end of gasket fits evenly into

bowl water inlet opening, and tank mounting bolts go through

mounting holes. Secure with metal washer/nuts. Use the included

deep socket tool to help get nuts started on bolts.

b. With tank parallel to wall, alternately tighten hex nuts keeping tank

even and level until tank contacts both front and rear bowl mounting

ribs. Do not tighten any further.

CAUTION:

DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT!

DO NOT SPIN BOLTS INSIDE TANK WITH A SCREWDRIVER

CLOSET FLANGE

WASHER/NUT

DEEP SOCKET

TOOL

SCREWDRIVER

RUBBER

GASKET

TANK MTG.

BOLTS PRE-

INSTALLED

WASHER/NUT

SCREWDRIVER

DEEP

SOCKET

TOOL

MTG.

RIBS

730529-100 Rev. U

- 4 -

109b

ADJUSTMENTS

a. Adjust water level. Water level should be adjusted to level indicated in

tank by adjusting float cup. See Step 11 for water level adjustment method.

IMPORTANT:

b. If bowl fails to siphon, an adjustment may be required with the lift chain.

Simply remove the bead chain from the retainment clip (see Fig. 10A)

and take up slack on the chain, and reinsert on lift rod. Make sure the chain

is not too taught.

With correct washers in

place (see Step 9a),

tighten COUPLING NUT

1/4 turn beyond hand tight.

DO NOT OVERTIGHTEN.

1. Turn off water supply and flush toilet to empty tank.

2. Disconnect chain from trip lever by removing hair pin cotter

and clevis pin.

3. Parially lift and support piston bottom with one hand.

4. Remove thumbscrew by turning counter-clockwise.

5. Remove piston top and gasket.

6. Replace gasket with new gasket.

7. Reverse procedure, turn thumbscrew until 2 clicks are felt.

TROUBLE SHOOTING FLUSH VALVE

SEAL REPLACEMENT:

NOTE: DO NOT ADD ANY FOREIGN MATERIALS TO THE SEALING SURFACE.

13 13a REFILL TUBE REPLACEMENT :

When cleaning your toilet, wash it with mild, soapy water, rinse

thoroughly with clear water and dry with a soft cloth.

WARNING: Do not use in-tank cleaners. These products

can seriously damage fittings in the tank. This damage can

cause leakage and property damage.

American Standard shall not be responsible or liable for

any damage caused by the use of in-tank cleaners.

CARE AND CLEANING

Turn on water supply.

Submerge the FLOAT

CUP under the water for

30 seconds. Adjust the

water to desired level by

turning WATER LEVEL

ADJUSTMENT ROD

and moving FLOAT

CUP up or down.

Diagram 1

TA N K

LEVER

REFILL

TUBE

TOP ARM NIPPLE

PARTS FOR WATER

CONNECTION

(SEE STEP 9)

CONE WASHER

VALVE

BODY

THREADED

SHANK

WASHER

COUPLING NUT

(HAND TIGHT ONLY)

FILL

VALVE

FLOAT

CUP

CRITICAL LEVEL

MARK ("C.L.")

MUST BE

1" ABOVE

OVERFLOW PIPE

ADJUSTABLE

HEIGHT

LOCK NUT

Fig. 10A

WATER LEVEL

ADJUSTMENT

ROD

Locate bottom portion of

hose clip to vent tube at

location as shown.

THUMBSCREW

PISTON TOP

PISTON BOTTOM

GASKET

HAIR PIN

COTTER

730529-100 Rev. U

- 5 -

Does not flush

Poor or sluggish flush

Toilet leaks

Toilet does not shut off

a. Water supply valve closed.

b. Supply line blocked.

c. Flush valve chain too loose or disconnected.

d. Sand or debris lodged in water control.

a. Bowl water level too low.

b. Supply valve partly closed.

c. Partially clogged trapway and/or drain pipe and/or vent.

d. Supply pressure too low.

e. Flush valve chain too tight, holding flush valve open.

a. Poor supply line connection.

b. Poor bowl to tank/floor connection.

a. Flush valve seal leaking or deformed.

b. Sand or debris lodged in water control.

a. Open valve and allow water to fill tank.

b. Shut off water supply, disconnect supply line and inspect all

gaskets and washers. Reassemble. Also, see Fluidmaster

maintenance. (see Step 14)

c. Readjust chain length as required.

d. Shut off water supply. Remove cap and clean as per Step 14.

a. Check that refill tube is connected to water control and

inserted into tank overflow without being kinked or damaged.

(see Step 13a)

b. Open supply valve fully. Be sure that proper supply tube size

is used.

c. Remove obstruction. Consult a plumber if necessary.

d. Normal supply pressure must be at least 20 psi.

e. Readjust chain length as needed. Review Step 10.

a. Review Step 9 of installation procedure.

b. Review Step 4 through 7 of installation procedure.

a. Clean debris from seal surface. Replace flush valve seal as

needed. (see Step 13)

b. Shut off water supply. Remove cap and clean as per Step 14.

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

REPAIR PARTS LIST

Repair parts are determined by toilet tank number which can be found marked inside tank.

NOTE: "XXX" represents color or trim finish options. Specify when ordering.

PART NO.

4266 Tank

With

735128 Cover

4266 RH Tank

With

735128 Cover

4272 Tank

With

735109 Cover

4281 Tank

With

735113 Cover

DESCRIPTION

Champion® 4 LH Trip Lever

Champion® 4 RH Trip Lever

Champion® 4 LH Trip Lever

Bolt Cap Kit (Incl. 2 Covers & Washers)

Champion® 4 Fluidmaster 400a Valve

Champion® 4 Flush Valve Seal Kit

Champion® 4 Flush Valve Assembly

Champion® 4 Clevis Pin Assembly

Champion® 4 PVC Refill Tube

Champion® 4 Tank To Bowl Coupling Kit #241

Champion® 4 Tank Cover

Clip for Refill Tube

738995-XXX0A

738997-XXX0A

738835-XXX0A

738837-XXX0A

034783-XXX0A

738565-424-0070A

7301111-0070A

3174.002-0070A

738985-0070A

738570-1010A

738756-0070A

735128-400-XXX

735109-400-XXX

735113-400-XXX

072989-0070A

✔

•

Make sure water supply is off.

Remove valve TOP by lifting

arm and rotating top and arm

1/8 turn counterclockwise,

pressing down slightly on cap.

IMPORTANT: Always clear

sand and rust from system.

• While holding a

container over the

uncapped VALVE to

prevent splashing, turn

water supply on and

off a few times. Leave

water supply off.

• Replace TOP by engaging

lugs and rotating 1/8 turn

clockwise. MAKE CERTAIN

TIP IS TURNED TO THE

LOCKED POSITION. VALVE

MAY NOT TURN ON IF TOP

IS NOT FULLY TURNED TO

THE LOCKED POSITION.

For troubleshooting information please contact:

TROUBLESHOOTING

IF FILL VALVE SHUTS OFF BUT CONTINUES TO

LEAK SLOWLY, repeat Step 14.

IF FILL VALVE TURNS OFF AND ON DURING

PERIODS OF NON-USE, it is a signal you are

wasting water because:

• The end of the refill tube is inserted into overflow

pipe, below water level in tank. Attach refill tube to

overflow pipe using "S" clip provided.

• The flush valve is leaking because it's worn, dirty

or misaligned.

IF FILL VALVE WON'T TURN ON OR SHUT OFF

or REFILL OF TANK WATER IS SLOW after valve

has been in use for some time, Fluidmaster Model

242 Replacement Seal may be needed.

Go to our website at www.fluidmaster.com for

American Standard Champion 4 2018 Users Manual 730529 En

2585 to the manual 2ea2fe38-95aa-40a9-b6db-752edb539b66

Navigation menu

Versions of this User Manual:

Views

Navigation