Amigo Technology APH50C Indoor Access point User Manual rev
Amigo Technology Inc. Indoor Access point Users Manual rev
Users Manual_rev.pdf
![](/img.php?id=4167368&img=bg1.png)
APH50C
Internal antenna
Indoor Access Point: APH50C/ APH51C
Quick Installation Guide
![](/img.php?id=4167368&img=bg2.png)
APH51C
External antenna
STEP 1. Package Content
(1) Access Point : APH50C/ APH51C/
(2) Power Adapter
(3) Wall Mounting screw set
(4) Ceiling mounting bracket
(9/16” and 15/16” flat T-bar included)
(5) Dipole 2.4G antennas x2, Dipole 5G antennas x2(APH51C/)
![](/img.php?id=4167368&img=bg3.png)
STEP 2. Mounting Kits Installation
For Wall Mount Installation
For Ceiling mount Installation
![](/img.php?id=4167368&img=bg4.png)
![](/img.php?id=4167368&img=bg5.png)
STEP 3. Connecting the Device for Configuration
(1) Connect one end of the Ethernet cable into the LAN1 port of the Access
Point and the other end to the Ethernet port on the computer.
(2) Plug in power source by different ways that depends on user setup
environment
(A) PoE Switch (Plug in from LAN1 Port)
(B) PoE Injector (Plug in from LAN1 Port)
(C) DC Power Adapter (Plug in from DC Jack)
- Connect the Power Adapter to the DC-IN port of the Access Point
and plug the other end into an electrical outlet.
Note: The Access Point supports both IEEE 802.3at PoE (Power over Ethernet) or the
included power adapter. You may use either one as the power source. DO NOT use both at
the same time.
STEP 4. IP Address Configuration
(1) Once your computer is on, ensure that your TCP/IP is enabled. Open
Network Connections and then click Local Area Connection. Select
Internet Protocol Version 4 (TCP/IPv4).
(2)If your computer is already on a network, ensure that you have set it to a
Static IP Address on the interface. (Example: 192.168.1.2 , the Subnet
Mask address as 255.255.255.0. and Default Gateway is 192.168.1.254 )
![](/img.php?id=4167368&img=bg6.png)
STEP 5. Access Point Setup
(1) Open a web browser on your computer. In the address bar of the web
browser, enter 192.168.1.1 and enter.
(2) A login screen will appear. The device do not have username and the
password settings and can click login to access.
(3) The access point user interface will appear. This device can operate in
Access Point operating mode. User can start to complete the device set up.
![](/img.php?id=4167368&img=bg7.png)
![](/img.php?id=4167368&img=bg8.png)
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
![](/img.php?id=4167368&img=bg9.png)
Professional installation instruction
1. Installation personal
This product is designed for specific application and needs to be installed by a qualified
personal who has RF and related rule knowledge. The general user shall not attempt to install
or change the setting.
2. Installation location
The product shall be installed at a location where the radiating antenna can be kept 20cm
from nearby person in normal operation condition to meet regulatory RF exposure
requirement.
3. External antenna
Use only the antennas which have been approved by the applicant. The non-approved
antenna(s) may produce unwanted spurious or excessive RF transmitting power which may
lead to the violation of FCC limit and is prohibited.
4. Installation procedure
Please refer to user’s manual for the detail.
5. Warning
Please carefully select the installation position and make sure that the final output power
does not exceed the limit set force in relevant rules. The violation of the rule could lead to
serious federal penalty.