Amigo Technology API50C Ruggedized Access Point User Manual API5XC QIG 0227 4

Download:
Mirror Download [FCC.gov]
Document ID	3767510
Application ID	GRKhAQ2EZZ8DoB9mW1paYg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	37.87kB (473349 bits)
Date Submitted	2018-03-02 00:00:00
Date Available	2018-03-05 00:00:00
Creation Date	2018-03-01 10:46:58
Producing Software	Microsoft® PowerPoint® 2010
Document Lastmod	2018-03-01 10:46:58
Document Title	API5XC-QIG-0227-4規格書
Document Creator	Microsoft® PowerPoint® 2010
Document Author:	CrystalLu

Step 5
Access Point Setup
(1)Open a web browser on your computer. In the
address bar of the web
browser, enter 192.168.1.254 and enter.
(2)A login screen will appear. By default, the username of the Access Point
is admin and the password is admin. Enter the
current username and
password of the Access Point and then click Login.
(Username: admin, Password: admin)
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
(3)The Access Point User Interface will appear. This
device can operate in Access Point operating mode.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 35cm between the radiator & your body.
Professional installation instruction
1. Installation personal
This product is designed for specific application and needs to be installed by a
qualified personal who has RF and related rule knowledge. The general user
shall not attempt to install or change the setting.
2. Installation location
The product shall be installed at a location where the radiating antenna can be
kept 35cm from nearby person in normal operation condition to meet regulatory
RF exposure requirement.
3. External antenna
Use only the antennas which have been approved by the applicant. The
non-approved antenna(s) may produce unwanted spurious or excessive RF
transmitting power which may lead to the violation of FCC limit and is
prohibited. The antenna must be installed completely perpendicular to the
horizon for compliance with FCC Rule Part 15.407(a)(1)(i).
4. Installation procedure
Please refer to user’s manual for the detail.
5. Warning
Please carefully select the installation position and make sure that the final
output power does not exceed the limit set force in relevant rules. The violation
of the rule could lead to serious federal penalty.
The antenna gain, antenna type and output power that can be used for the
device and the info listed below are correct and represent the product.
Antenna type
2.4GHz
~2462MHz)
(2412
Antenna Gain Max power
5GHz band 1 (5 180~5240MHz
Max power
Antenna Gain
5GHz band 4 (5745~5825MHz)
Antenna Gain
Max power
Internal Patch
8.4dBi
497.225mW
7.0dBi
173.482mW
7.3dBi
710.614mW
External Dipole
4.92dBi
645.727mW
6.87dBi
201.971mW
6.92dBi
782.596mW
Quick Installation Guide
Ruggedized Access Point
Step 1
(B) PoE Injector (Plug in from LAN1 Port)
Package Content
▉ For Pole mount Installation:
Thread the open end of the pole strap through the
two tabs on the Access Point pole mount hole. Lock
and tighten pole strap to secure the device to the
pole. Make sure the antenna installed completely
perpendicular to the horizon direction.
(1)Access Point
(2)Power Adapter
(4)Wall Mounting kit
(C) DC Power Adapter (Plug in from DC Jack)
-Connect the Power Adapter to the DC-IN port of
the Access Point and plug the other end into an
electrical outlet.
(3)Wall Mounting
screw set
(5)Hose Clamp
Note: The Access Point supports both IEEE 802.3at
PoE (Power over Ethernet) or the included power
adapter. You may use either one as the power source.
DO NOT use both at the same time.
(6)Antenna
(for API51c)
Step 4
IP Address Configuration
Step 2
Mounting Kits Installation
▉ For Wall Mount Installation:
(1)Determine where the mounting
plate of Access Point to be placed
and mark location on the surface
for the two mounting holes.
Use the appropriate drill bit to drill
two 26mm depth holes in the
markings and hammer the bolts
into the openings.
(2)Screw the anchors into the
holes until they are flush with the
wall.
(3)Put mounting plate on the wall to map with hole of
anchor then screw the included screws into the
anchors.
(4)Place the Access Point against wall fitting
throughout the slots of the Access Point.
Step 3
Connecting the Device for Configuration
(1)Connect one end of the Ethernet cable into the
LAN1 port of the Access Point and the other end to
the Ethernet port on the computer.
(1)Once your computer
is on, ensure that your
TCP/IP is enabled.
Open Network
Connections and then
click Local Area
Connection. Select
Internet Protocol
Version 4 (TCP/IPv4).
(2)Plug in power source by different ways that
depends on user setup
environment
(A) PoE Switch (Plug in from LAN1 Port)
(2)If your computer is already
on a network, ensure that you
have set it to a Static IP
Address on the interface.
(Example: 192.168.1.2 , the
Subnet Mask address as
255.255.255.0. and Default
Gateway is 192.168.1.254 )

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Language                        : zh-TW
Tagged PDF                      : Yes
Title                           : API5XC-QIG-0227-4規格書
Author                          : CrystalLu
Create Date                     : 2018:03:01 10:46:58+08:00
Modify Date                     : 2018:03:01 10:46:58+08:00
Producer                        : Microsoft® PowerPoint® 2010
Creator                         : Microsoft® PowerPoint® 2010

EXIF Metadata provided by EXIF.tools