Amx Modero Nxt 1200V Users Manual 0362856

nxt1200v ab546ff2-53f1-4ca9-a758-ce0c621619f7 AMX Computer Monitor NXT-1200V User Guide |

2015-02-05

: Amx Amx-Modero-Nxt-1200V-Users-Manual-508942 amx-modero-nxt-1200v-users-manual-508942 amx pdf

Open the PDF directly: View PDF .
Page Count: 196

Download
Open PDF In Browser	View PDF

Operation/Reference Guide

Modero® 1200V
G4 Touch Panels
NXD-1200V and NXT-1200V
12” Modero Video Touch Panels

To u ch P a n e l s

L as t R e vi s ed: 1 0 /1 /20 0 8

AMX Limited Warranty and Disclaimer
AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from
the date of purchase from AMX, with the following exceptions:
•

Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch
overlay components that are warranted for a period of one (1) year.

•

Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one
(1) year.

•

AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting
products, as long as the AMX Lighting products are under warranty. AMX does guarantee the control of dimmable
loads that are properly connected to our lighting products. The dimming performance or quality cannot be
guaranteed due to the random combinations of dimmers, lamps and ballasts or transformers.

•

Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year.

•

AMX Software is warranted for a period of ninety (90) days.

•

Batteries and incandescent lamps are not covered under the warranty.

This warranty extends only to products purchased directly from AMX or an Authorized AMX Dealer.
All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is obtained
from the AMX RMA Department. The RMA number must be clearly marked on the outside of each box. The RMA is
valid for a 30-day period. After the 30-day period the RMA will be cancelled. Any shipments received not consistent
with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products returned without a
valid RMA number.
AMX is not liable for any damages caused by its products or for the failure of its products to perform. This includes any
lost profits, lost savings, incidental damages, or consequential damages. AMX is not liable for any claim made by a
third party or by an AMX Dealer for a third party.
This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim
(including negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot
be waived or amended by any person. This limitation of liability will be effective even if AMX or an authorized
representative of AMX has been advised of the possibility of any such damages. This limitation of liability, however, will
not apply to claims for personal injury.
Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or
exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of
the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may also
have other rights that vary from state to state. The owner is advised to consult applicable state laws for full
determination of rights.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX MAKES NO OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. AMX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED
WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF
THIS LIMITED WARRANTY.

FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received; including interference
that may cause undesired operation.

Federal Communications Commission (FCC)
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This
equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed an operated with a minimum distance of 20 centimeters between the radiator and your body.

Table of Contents

Table of Contents
Introduction ........................................................................................................1
Modero Video Touch Panels (1200V-Series) ............................................................. 1
Product Specifications (NXD-1200V and NXT-1200V) .............................................. 2
1200V-Series Modero Connectors ............................................................................ 5
Cleaning the Touch Overlay ............................................................................................ 5

Connecting and Using Input Devices ........................................................................ 6

Touch Panel Accessories .....................................................................................7
NXA-AVB/ETHERNET Breakout Box (FG2254-10) .................................................... 7
Product Specifications .................................................................................................... 7
Installing the NXA-AVB/ETHERNET ................................................................................ 8
Wiring the NXA-AVB/ETHERNET connectors and cables ................................................ 9
Wiring the NXA-AVB/ETHERNET for Unbalanced Audio............................................... 10
Wiring the NXA-AVB/ETHERNET for Balanced Audio ................................................... 10

Modero Table Top Cable (CA2250-50) ................................................................... 11
Product Specifications .................................................................................................. 11
Wiring information for the Modero Table Top cable..................................................... 12
Installing CAT5 Suppression Ferrites............................................................................. 14

NXA-CFTP Compact Flash (FG2116-2x) .................................................................. 15
NXA-PCI80211G Wireless Card (FG2255-04).......................................................... 16
Product Specifications

............................................................................................... 16

Installation and Upgrade of the Internal NXT Components .................................... 18
Step 1: Remove the existing NXT Outer Housing ......................................................... 18
Step 2: Install the 802.11g mini-PCI Wireless Card ....................................................... 19
Step 3: Install the Compact Flash Memory Card upgrade............................................. 21
Step 4: Close and Resecure the NXT Panel Enclosure................................................... 22

Installation and Upgrade of the Internal NXD Components ................................... 22
Step 1: Remove the existing NXD Outer Housing ........................................................ 22
Step 2: Install the new 802.11g mini-PCI Wireless card (NXD)...................................... 23
Step 3: Install the new Compact Flash Memory card (NXD).......................................... 23
Step 4: Close and Resecure the NXD Panel Enclosure .................................................. 24

NXT-BP Power Pack (FG2255-10) ........................................................................... 25
Product Specifications................................................................................................... 25

NXA-BASE/B Battery Base Kit (FG2255K) .............................................................. 25
Product Specifications .................................................................................................. 26
Checking the NXT-BP battery charge............................................................................ 26
Installing the NXA-BASE/B to an NXT Modero Panel.................................................... 27
Installing an NXT-BP into the NXA-BASE/B................................................................... 28

1200V Modero Video Touch Panels

Table of Contents

Charging the NXT-BP batteries with the NXA-BASE/B ................................................. 29

NXT-CHG Battery Charger Kit (FG2255-50K) ......................................................... 29
Product Specifications .................................................................................................. 30
Powering the NXT-CHG ................................................................................................ 30
Reading NXT-CHG LED Indicator .................................................................................. 30
Charging the NXT-BP batteries using the NXT-CHG ..................................................... 31
Recalibrating the batteries ............................................................................................ 31

Installation Procedures: NXD-1200V Panels .....................................................33
Unpacking the Panel ............................................................................................... 33
Installing the Internal Components ......................................................................... 33
Upgrading to the MB-TP12 VESA Mounting Kit ..................................................... 33
Removing the Original Modero Back Box ..................................................................... 34
Installing the MP-TP12 Back Box ................................................................................... 34
Cable Installation for the MP-TP12 Back Box ................................................................ 35
Finalizing the installation............................................................................................... 35

Pre-wall Installation of the Conduit Box.................................................................. 37
Installation of the NXD Touch Panel ....................................................................... 38
Installing the NXD panel within a Conduit Box ............................................................. 38
Installing the NXD into drywall using Expansion Clips .................................................. 40
Installing the NXD into a Flat Surface using #4 screws ................................................. 42
Installing an NXD into an (optional) Rack Mount Kit (NXA-RK12) ................................. 44

Wiring Guidelines for the 1200V Panels ................................................................. 45
Preparing captive wires................................................................................................. 45
Wiring a power connection ........................................................................................... 46

Audio/Video Port: Connections and Wiring ............................................................ 46
Ethernet/RJ-45 Port: Connections and Wiring ........................................................ 47

Panel Calibration ..............................................................................................49
Calibrating the Modero Panel................................................................................. 49
Testing your Calibration ................................................................................................ 50

Configuring Communication .............................................................................51
Modero Setup and System Connection .................................................................. 51
Configuring and Using USB with a Virtual Master .................................................. 53
Step 1: Setting up the Panel and PC for USB Communication ...................................... 53
Step 2: Confirming the Installation of the USB Driver on the PC .................................. 54
Step 3: Confirm and View the current AMX USB device connections ........................... 56
Step 4: Using a USB to Configure a Virtual Master (using NetLinx Studio) ................... 56
Step 5: Confirm and View the current AMX USB device connections ........................... 58

Wireless Settings Page - Wireless Access Overview ............................................... 59
IP Routing...................................................................................................................... 59

1200V Modero Video Touch Panels

Table of Contents

Hot Swapping ............................................................................................................... 59

Configuring a Wireless Connection......................................................................... 60
Step 1: Configuring the Panel’s Wireless IP Settings .............................................. 60
Wireless communication using a DHCP Address ........................................................... 60
Wireless communication using a Static IP Address........................................................ 61

Step 2: Configuring the Card’s Wireless Security Settings ..................................... 62
Configuring the Modero’s wireless card for unsecured access to a WAP200G ............. 62
Configuring the Modero’s wireless card for secured access to a WAP200G................. 63
Configuring multiple wireless Moderos to communicate to a target WAP200G........... 66

Configuring a Wired Ethernet Connection.............................................................. 67
Step 1: Configuring the Panel’s Wired IP Settings.................................................. 67
IP Settings section - Configuring a DHCP Address over Ethernet ................................. 67
IP Settings section - Configuring a Static IP Address over Ethernet ............................. 68

Step 2: Choosing a Master Connection Mode Setting ............................................ 68
Step 3: Configuring the Ethernet Connection Type................................................ 69
Master Connection - Virtual Master communication over Ethernet............................... 70
Master Connection section - NetLinx Master Ethernet IP Address - URL Mode ............ 72
Master Connection section - NetLinx Master Ethernet IP Address - Listen Mode ......... 72
Master Connection section - NetLinx Master Ethernet IP Address - Auto Mode .......... 73

Using G4 Web Control to Interact with a G4 Panel ................................................ 74
Using your NetLinx Master to control the G4 panel ............................................... 76

Upgrading Modero Firmware ...........................................................................79
Upgrading the Modero Firmware via the USB port ................................................ 79
Step 1: Configure the panel for a USB Connection Type .............................................. 79
Step 2: Prepare NetLinx Studio for communication via the USB port ........................... 80
Step 3: Confirm and Upgrade the firmware via the USB port ....................................... 81

Upgrading the Modero Firmware via an IP Address............................................... 83
Step 1: Prepare the Master for communication via an IP .............................................. 83
Step 2: Prepare the panel for communication via an IP ................................................ 84
Step 3: Verify and Upgrade the panel firmware via an IP ............................................. 85

Upgrading Accessory Devices via the USB ............................................................. 86
Step 1: Prepare the NXA-BASE/B for firmware transfer via USB .................................. 87
Step 2: Upgrade the NXA-BASE/B firmware via USB.................................................... 88

Upgrading Accessory Devices via an IP Address .................................................... 89
Step 1: Prepare the NXA-BASE/B for firmware transfer via an IP ................................. 89
Step 2: Upgrade the NXA-BASE/B firmware via an IP................................................... 90

Firmware Pages and Descriptions ....................................................................93
Setup Navigation Buttons....................................................................................... 93
Setup Page ............................................................................................................. 94

1200V Modero Video Touch Panels

iii

Table of Contents

Project Information Page............................................................................................... 96
Panel Information Page ................................................................................................. 97
Time & Date Setup Page ............................................................................................... 98
Volume Page ................................................................................................................. 99
Supported sampling rates for WAV............................................................................. 100
Protected Setup Page ................................................................................................. 100
Video Adjustment Slide-Out Option Bar ..................................................................... 101
Video Adjustment - Video Adjustment Page ............................................................... 101
Battery Base Page ....................................................................................................... 102

Protected Setup Navigation Buttons .................................................................... 104
Protected Setup Page........................................................................................... 105
G4 Web Control Page ................................................................................................. 108
Sensor Setup Page ...................................................................................................... 110
Using the Automated Brightness Control feature (DIM Mode) ................................... 111
Password Setup Page.................................................................................................. 112
Calibration Page.......................................................................................................... 113
Wireless Settings Page ................................................................................................ 114
System Settings Page.................................................................................................. 118

Programming ..................................................................................................121
Button Assignments ............................................................................................. 121
Page Commands ................................................................................................... 121
Programming Numbers......................................................................................... 127
RGB triplets and names for basic 88 colors ................................................................ 127
Font styles and ID numbers ......................................................................................... 129
Border styles ............................................................................................................... 130

"^" Button Commands ......................................................................................... 132
Text Effect Names ................................................................................................ 152
Button Query Commands ..................................................................................... 153
Panel Runtime Operations .................................................................................... 162
Input Commands................................................................................................... 166
Embedded Codes ................................................................................................. 168
Panel Setup Commands ........................................................................................ 169
Dynamic Image Commands................................................................................... 170

Troubleshooting .............................................................................................173
Appendix A ....................................................................................................177
Text Formatting Codes for Bargraphs/Joysticks ................................................... 177
Text Area Input Masking....................................................................................... 178
Input mask character types ......................................................................................... 178
Input mask ranges ....................................................................................................... 179

1200V Modero Video Touch Panels

Table of Contents

Input mask next field characters ................................................................................. 179
Input mask operations................................................................................................. 179
Input mask literals ....................................................................................................... 179
Input mask output examples ....................................................................................... 180

URL Resources ...................................................................................................... 181
Special escape sequences ........................................................................................... 181

1200V Modero Video Touch Panels

Table of Contents

1200V Modero Video Touch Panels

Introduction

Introduction
AMX has taken a great leap forward with the release of their new 1200V-Series of Modero touch panels.
These panels offer the ability to display Composite video, 802.11g communication, and USB support for
extended input devices, and panel programming via a mini-USB port. The new G4 graphics and Video
technology is supported by the release of the latest TPDesign4 Touch Panel Design Program. These
video-capable panels support several video formats: NTSC, SECAM, and PAL (Color Active (CA)
panels don’t support video).
Each 1200V-Series panels have been pre-installed with 2 antennas which can be later used to
configure each panel type for wireless communication (via an optional NXA-80211G wireless
mini-PCI card).

Modero Video Touch Panels (1200V-Series)
The new and enhanced line of 12" Modero Touch Panel (NXT/NXD-1200V) represent the next step in
video-capable panels and departs from the previously popular CA version. In addition to
Composite/S-Video support (does not support Component RGB signals), the new 1200V panels feature
dual USB connectivity for mouse and keyboard, and antennas, the use of a mini-USB port for panel
programming and a complete departure from the use of an ICSNet connector for communication. These
panels include a built-in microphone, left/right speakers, audio/headphone connector, and an included
audio/video breakout box.
Table Top models use AMX’s exclusive SmoothTilt® technology for effortless adjustment of the
viewing angle.
Each panel is sold only as part of a 1200V Kit which includes both a panel and an
NXA-AVB/ETHERNET Audio/Video Breakout Box (FG2254-10). This box facilitates the installation
and distribution of video, data, and audio to Modero touch panels located up to 200 feet (60.96 m) from
the breakout box. These panels are ideally suited for displaying full motion video and audio with overlay
graphics for applications with demanding visual requirements. The following is a listing of the currently
available 1200V panels:
1200-V Modero Video Touch Panels
NXD-1200V
(FG2251-60K)

12" Modero Video WallMount Touch Panel Kit
(includes both an NXD panel and an NXA-AVB/ETHERNET A/V Breakout Box).

NXT-1200V
(FG2250-60K)

12" Modero Video Table Top Touch Panel Kit
(includes both an NXD panel and an NXA-AVB/ETHERNET A/V Breakout Box).

Sample
NXD-1200V
(front view)

Sample
NXT-1200V
(front view)

FIG. 1 Sample 1200V Video Touch Panels (front views)

1200V Modero Video Touch Panels

Introduction

Product Specifications (NXD-1200V and NXT-1200V)
The following table outlines the specifications for 1200V-Series of 12" Modero panels.
1200V Panel Specifications
Dimensions (HWD):

• NXD-1200V (with faceplate): 12.38" x 12.59" x 3.25"
(31.43 cm x 31.97 cm x 8.25 cm)
• NXT-1200V (Fully raised): 10.91" x 12.34" x 12.50"
(27.70 cm x 31.33 cm x 31.75 cm)
• NXT-1200V (Fully lowered): 6.77" x 12.34" x 12.50"
(17.20 cm x 31.33 cm x 31.75 cm)
• CB-TP12 (conduit/wallbox): 11.52" x 11.60" x 3.50"
(29.27 cm x 29.47 cm x 8.89 cm)
• MB-TP12 (VESA mounting box): 12.37" x 12.58" x 3.52"
(31.42 cm x 31.95 cm x 8.94 cm)

Power Requirements:

• Constant current draw: 2.1 A @ 12 VDC (stand-alone)
• Startup current draw: 3.2 A @ 12 VDC (stand-alone)

Memory (factory default):

• 256 MB on-board memory
• 128 MB Compact Flash (upgradeable to 1 GB factory programmed)

Weight:

• NXD-1200V: 10.80 lbs (4.90 kg)
• NXT-1200V: 10.80 lbs (4.90 kg)

Panel LCD Parameters:

• Aspect Ratio: 4 x 3
• Brightness (luminance): 250 cd/m2
• Channel transparency: 8-bit Alpha channel transparency
• Contrast ratio: 300:1
• Display area (HW): 183.10 mm x 247.40 mm
• Display colors: 256K (18-bit color depth)
• Dot/Pixel pitch: 0.297 mm
• Screen resolution (HV): 800 x 600 pixels
• Video formats: NTSC, PAL, and SECAM (shown within variable-size
video windows)

Active Screen Area:

• 9.68” x 7.26” (24.60cm x 18.45cm)

Viewing Angles:

• Vertical: + 80° (up from center) and - 80° (down from center)

Features:

• Enhanced hardware security (via an externally mounted Kensington
Lock system)
• Ethernet connectivity (replaced ICSNet as a method of communication)
• New and improved connector compartment
• Pre-installed 802.11g wireless card and integrated antennas (NXT
models only)
• Wired Ethernet @10/100 and Wireless Ethernet 802.11g
• USB mouse/keyboard/programming ports
• Support of the latest G4 applications: G4 Computer Control, G4Web
Control®, Dynamo, TakeNote™, and PictureFrame™.

Supported Audio Sample Rates: • 48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz, 12000Hz,
11025Hz, and 8000Hz.
Certifications:

• FCC Part 15 Class B, CE, and EN 60950

1200V Modero Video Touch Panels

Introduction

1200V Panel Specifications (Cont.)
Button Assignments:

Button assignments can only be adjusted in TPD4 and not on the panels.
• Button channel range: 1 - 4000 button push and Feedback (per address
port)
• Button variable text range: 1 - 4000 (per address port)
• Button states range: 1 - 256 (General Button; 1 = Off State, 2 = On State)
• Level range: 1 - 600 (default level value 0-255, can be set up to 1-65535)
• Address port range: 1 - 100

Front Panel Components:
Light sensor:

• Photosensitive light detector for automatic adjustment of the panel
brightness (a dim room results in a dimmer LCD display and a bright
room results in a brighter LCD display).
Note: The light sensor can be adjusted via the Sensor Setup Page section
on page 110.

Motion sensor (PIR):

• Proximity Infrared Detector to wake the panel when the panel is
approached.
• Activation range: + 20° vertically from center and + 45° horizontally
from center.
Note: The motion sensor can be adjusted via the Sensor Setup page
(Sensor Setup Page section on page 110).

Front setup access button:

• Provides both access to the Setup and Calibration pages and toggles the
panel between a "sleep" and "wake" state.
- When wired, "sleep" status means the backlight is Off.
- When battery operated, wireless "sleep" status means the touch panel
base is either Off or "suspended".

Microphone:

• Used for intercom applications
(requires an NXA-AVB/ETHERNET Breakout Box for analog
communication).

Speakers:

• Stereo output with a frequency response of 450 Hz - 7 KHz

Rear Panel Components:
Audio/Video connector:

(Side panel location on NXD-Wall Mount panels)
• RJ-45 connector for communication of differential audio/video signals
to/from the touch panel (panel type dependant). This connector receives
Composite video, Stereo (left/right) audio, and microphone audio.
• Video is received via the NXA-AVB/ETHERNET Breakout Box.
Configuring video windows for playback is done using TPDesign4.
• In-bound audio (from the breakout box) gets directed to the speakers.
• Out-bound audio is sent from the on-board microphone (on the
front-panel). Selecting audio files for playback is configured through
TPDesign4.

Ethernet 10/100 port:

• RJ-45 port for 10/100 Mbps communication. The Ethernet port
automatically negotiates the connection speed (10 Mbps or 100 Mbps),
and whether to use half duplex or full duplex mode.
• These panels communicate with the NetLinx® Master using the ICSP
protocol over Ethernet.

Ethernet 10/100 LEDs:

• LEDs show communication activity and connection information:
A-activity - Yellow LED lights when receiving or transmitting Ethernet
data packets.
L-link - Green LED lights when the Ethernet cables are connected and
terminated correctly.

PWR connector:

1200V Modero Video Touch Panels

• 2-pin 3.5 mm mini-Phoenix connector.

Introduction

1200V Panel Specifications (Cont.)
Rear Panel Components
(Cont.):

(Side panel location on NXD-Wall Mount panels)

Stereo Output connector:

• Stereo output through a 3.5mm mini-jack (for use with external
speakers).

USB connector (2):

• The two Type-A USB ports can connect up to two external keyboard or
mouse devices for use with Virtual PC applications.

Mini-USB connector:

• 5-pin Mini-USB connector used for programming, firmware update, and
touch panel file transfer between the PC and the target panel.
Note: When connecting the panel to PC using a CC-USB (or compatible)
cable, be sure to power the panel On before attempting to connect the
USB cable from the PC to the mini-USB port on the panel.
Refer to Step 5: Confirm and View the current AMX USB device
connections section on page 58 for more information.

Operating / Storage
Environment:

• Operating Temperature: 10° C (50° F) to 40° C (104° F)
• Operating Humidity: 20% to 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% to 85% RH

Included Accessories:

• Installation Kit for 12" and 17" NXD panels (KA2251-01):
- 2-pin mini-Phoenix connector (41-5025)
- Four Drywall clips (62-5924-05) and #6 - sheet metal screws
- One CAT5 Suppression Ferrites (04-0014)
- Three Phillips-head screws (#4-20 x 0.250 Black)
• Installation Kit for 12" NXT panels (KA2251-03):
- 2-pin mini-Phoenix connector (41-5025)
- Three Phillips-head screws (#4-20 x 0.250 Black)
- Two CAT5 Suppression Ferrites (04-0014)
• Modero Table Top Cable (CA2250-50)
- provided with all NXT Table Top panels.
• NXA-AVB/ETHERNET Breakout Box (FG2254-10): Provides video/audio
distribution to the A/V panel over CAT5 cable (up to 200’/60.96m) and
accepts either Composite or S-Video.
- Although the 1200V is only sold as part of a KIT configuration,
the breakout box can be purchased separately.

Other AMX Equipment:

• CB-TP12 (FG031-10)
- 12" metallic conduit box for Wall Mount installations.
• CC-USB (Type-A) to Mini-B 5-Wire programming cable (FG10-5965)
• MB-TP12 Universal VESA Mounting Box for NXD panels (FG031-50):
- Black metallic VESA back box (62-0031-50)
- Black plastic cover (with grommet opening) (60-0031-50)
- Strain relief grommet (45-0004-03)
- Four Phillips pan-head screws (#8-32 x 0.50 Black) (80-0146-02)
- Twelve Under-cut Phillips-head screws (#6-32 x 0.500 Black) (800139)
• NXA-BASE/B (FG2255)
- Wireless base for Table Top touch panels (NXT models only).
• NXA-KLB Kensington Lock Kit for NXT panels (FG2259-10)
(optional only with NXT models)
• NXA-PCI80211G Wireless Card (FG2255-04)
- Although both panel types have the antennas pre-installed, installation
of the optional mini-PCI card is required to initiate wireless
communication.

1200V Modero Video Touch Panels

Introduction

1200V Panel Specifications (Cont.)
Other AMX Equipment (Cont.):

• NXA-RK12 (FG2904-50)
- RackMount kit for 12" Wall Mount touch panels (NXD models only).
• NXT-BP (FG2250-10)
- Battery pack for Table Top panels. Provides 4 hours of continual
operation (NXT models only)
• NXT-CHG (FG2250-50)
- Battery charger for NXT-BP batteries. Charges batteries in 8 hours.
• Upgrade Compact Flash (factory programmed with firmware):
NXA-CFTPV256M - 256 MB V/VG compact flash card (FG2116-43)
NXA-CFTPV512M - 512 MB V/VG compact flash card (FG2116-44)
NXA-CFTPV1G - 1 GB V/VG compact flash card (FG2116-45)

1200V-Series Modero Connectors
FIG. 2 shows the connectors on the 1200V Modero Video panels. The Audio/Video RJ-45 connector
provides differential audio/video signals between the touch panel and the NXA-AVB/ETHERNET.
This connector routes Composite video, Stereo (left/right) audio, and microphone audio.

NXT-1200V - connectors located
on rear panel of the base
A

NXD-1200V - connectors located
on left side panel

L
12VDC

AUDIO/VIDEO

Audio-Video from
NXA-AVB/ETHERNET
(CAT5)

ETHERNET

Ethernet
(CAT5)

PROGRAM

PWR

Power

Stereo
Output

Keyboard/Mouse
USB connectors (2)

Mini-USB
(Program Port)

FIG. 2 Connector layout on sample 1200V Video Touch Panels

Cleaning the Touch Overlay
You should clean the touch screen overlay after each day’s use. Always use clean cotton cloths and a
spray bottle containing water.

1200V Modero Video Touch Panels

Introduction

Connecting and Using Input Devices
The 1200V panel can have up to two USB-capable input devices connected for use on its different
firmware and TPD4 panel pages. These input devices can consist of a keyboard or mouse.
USB-connected input devices are not detected and recognized by the panel until
power is cycled to the unit.
A mini-USB connection is only detected after it is installed onto an active
panel. Connection to a previously powered panel, allows the PC to detect the
panel and assign an appropriate USB driver.

1. Insert the input device USB connectors into the appropriate USB connector on the panel.
2. Press the on-screen Reboot button from the Protected Setup page to save any changes and restart
the panel.
3. After the panel splash-screen disappears:
If a USB mouse has been connected, a mouse cursor appears on the panel screen and its
location corresponds to the mouse cursor position sent by the external USB mouse.
If a USB keyboard has been connected, only on-screen keyboards and keypads will reflect any external
keystrokes sent from the external USB keyboard.

1200V Modero Video Touch Panels

Touch Panel Accessories

Touch Panel Accessories
The following section outlines and describes both the included accessories and other AMX equipment
available for these touch panels.

NXA-AVB/ETHERNET Breakout Box (FG2254-10)
The NXA-AVB/ETHERNET Breakout Box (FIG. 3) is included as part of the 1200V Kit configuration
(panel and box) but can be purchased as a separate accessory. This box facilitates the installation and
distribution of video, data, and audio to Modero touch panels located up to 200 feet (60.96 m) from the
AVB box. This unit accepts either Composite or S-Video from standard video devices.
This breakout box can be mounted on either a horizontal flat surface or in an equipment rack
(by using an optional AC-RK Rack Kit).
Composite/
S-Video
Luma
(rear)

Audio
In

Ethernet (to panel)

S-Video Chroma
Power In

(front)

Mic Out

Ethernet In

Power (to panel)

Audio/Video
(to panel)

FIG. 3 NXA-AVB/ETHERNET Breakout Box (front and rear views)

Product Specifications
NXA-AVB/ETHERNET Specifications
Dimensions (HWD):

• 1.50" x 5.55" x 4.88" (3.81 cm x 14.10 cm x 12.40 cm)
• Width when attached to mounting ears: 6.65" (16.89 cm)

Power Consumption:

• 50mA (with audio/video input)
• 23mA (with no audio/video)
• Routed through NXA-AVB/Ethernet using a 12 VDC-compliant power supply

Certifications:

• FCC Part 15 Class B, CE, and EN 60950

Features:

• Accepts either Composite or S-Video (video-capable panels only)
• Provides audio distribution to the non-video touch panels over a CAT5 cable
(up to 200 ft.)
• Provides video/audio distribution to the video-capable touch panels over
CAT5 cable up to 200 ft. (60.9 m)

Availability:

• This unit is included with CV5, CV7, CV10, and 1200V-Series Kit
configurations

Front Components:

• 2-pin 3.5 mm Phoenix connector for power to the touch panel
• Green LED provides an indication of power status
• RJ-45 connector provides Ethernet signals to the touch panel
• RJ-45 connector provides differential audio and video signals to the touch
panel (panel type dependant)

1200V Modero Video Touch Panels

Touch Panel Accessories

NXA-AVB/ETHERNET Specifications (Cont.)
Rear Components:

• 6-pin 3.5 mm Phoenix connector for in-bound (left/right channel) audio
• 4-pin 3.5 mm Phoenix connector for out-bound (from microphone) audio
• BNC connector (female) for Composite or Chroma (for video-capable
panels only)
• BNC connector (female) for luminance (for video-capable panels only)
• RJ-45 connector for Ethernet input from the control system
• 2-pin 3.5 mm Phoenix connector for in-bound power

Included Accessories:

• Two 2-pin Phoenix connectors (41-5025)
• 4-pin Phoenix connector (41-5047)
• 6-pin Phoenix connector (41-5063)
• Rack Mount Kit (KA2250-40) with mounting bracket (62-2254-02)

Other AMX Equipment:

• AC-RK Accessory RackMount Kit (FG515)
• Modero Table Top Cable (CA2250-50)

Installing the NXA-AVB/ETHERNET
A 12 VDC-compliant power supply can indirectly provide power to a Modero panel by routing power
through the NXA-AVB/ETHERNET Breakout Box. FIG. 4 shows a sample wiring configuration using
both an indirect or direct power connection for a video-capable Modero panel.
Indirect
Connect

Ethernet In
(RJ-45)

Mic Out
(4-pin captive-wire)

Video In
(BNC)

12 VDC power
supply

Line Level out
(to amplifier
or VOL card)

Audio In
(6-pin captive-wire)

(rear)

NXA-AVB/ETHERNET
Breakout Box
Power
supplied via
NXA-AVB box

(front)

Ethernet
(CAT5)

12 VDC power
supply
Direct
Connect

Audio/Video
(CAT5)

or
NXD/T Video-capable
Touch Panels

FIG. 4 Sample wiring configuration on video-capable panels using this breakout box

A 12 VDC-compliant power supply can also directly provide power through the unit to a target Modero
panel. FIG. 5 shows a sample wiring configuration for a non-video capable Modero panel.
Direct
connect
12 VDC power
supply

Ethernet
(CAT5)

Audio (CAT5)
between the
NXA-AVB/ETHERNET
Breakout Box

NXD/T Non-video capable
Touch Panels
FIG. 5 Sample wiring configuration using CA Modero panels

1200V Modero Video Touch Panels

Touch Panel Accessories

The breakout box unit can be mounted on either a horizontal flat surface or into an
equipment rack (by removing the front screws and attaching it to an optional AC-RK).
The power supply being used on the NXA-AVB/ETHERNET is dependant on the
power requirements of the target touch panel.

Use a standard CAT5 Ethernet cable to provide both communication and 10/100 network connectivity
between the panel, NXA-AVB/ETHERNET, NetLinx Master, and the network.

Wiring the NXA-AVB/ETHERNET connectors and cables
The inputs and outputs on the breakout box are separated into front and rear connectors. The rear
connectors are used to input external signals. The front connectors are used to communicate signals
between the NXA-AVB/ETHERNET and a target Modero panel. FIG. 6 provides a layout of the wiring
connection both into and from the breakout box.
GND

Audio In - Left Channel

F
R
O
N
T

In (-)

(6-pin captive wire)

In (+)

Audio In - Right Channel

NXA-AVB/ETHERNET
Breakout Box

(6-pin captive wire)

GND
In (-)
In (+)

Microphone Out

GND(-)
Out (-)

(4-pin captive wire)

Out (+)

Comp/Y (BNC)
C (BNC)
Ethernet
(RJ-45)
12 VDC power
supply

R
E
A
R

Audio/Video
(CAT5)
Ethernet Out
(CAT5)
Power to
touch panel

FIG. 6 NXA-AVB/ETHERNET Breakout Box connector wiring diagram

The rear-panel wiring connections are described below (from left to right):
• AUDIO IN:

6-pin mini-Phoenix connector, divided into left and right audio channels. Each
channel is divided into GND, IN+, and IN- terminal cable connectors
(2 sets of 3 for each channel).
An example of this cable is to strip the ends of 2 RCA audio cables and insert
them into their respective locations on the Audio In port.
Either a balanced (+, -, and GND) or unbalanced (+ and GND) audio
signal can be connected to this input.

• MIC OUT:

4-pin mini-Phoenix connector, divided into GND, OUT-, and OUT+ terminal
connectors.
An example of this cable is to strip the terminal ends of a 3.5mm mini-jack and
insert them into their respective locations on the Mic Out port. This signal can
be fed as a Line Level In to either an amplifier or an AMX VOL card.
Either a balanced (+, -, and GND) or unbalanced (+ and GND) audio signal
can be connected to this output.

• Video In BNCs: Feeds either Composite/S-Video Luma or S-Video Chroma signals into the
NXA-AVB/ETHERNET. This feed is then redirected out to a Modero panel
through the front Audio/Video CAT5 port.
• ETHERNET:

1200V Modero Video Touch Panels

RJ-45 connector routes data to the G4 touch panel through the front Ethernet
port. These connections use a standard CAT5 Ethernet cable to provide
communication between the target touch panel, breakout box, and NetLinx
Master.

Touch Panel Accessories

• PWR:

2-pin mini-Phoenix connector that connects to a 12 VDC-compliant power
supply. This port can be used to provide power to a Modero panel by sending it
through the NXA-AVB/ETHERNET (rear power connector through to the front
power connector).

Wiring the NXA-AVB/ETHERNET for Unbalanced Audio
Most domestic audio equipment has unbalanced audio inputs and outputs. This means that the audio
output (left, right, or mono) appears on a single wire, and is referenced to "0 V" or "Ground". Typical
connectors used are RCA "phono" connectors, DIN plugs/sockets, and 0.25" (6.3mm) or 3.5mm jack
plugs/sockets.
Unbalanced audio is adequate for most domestic environments and for line-level signals in a typical
broadcast studio. Problems may occur if the signals are carried over long distances, especially if the
source and destination have separate main supplies. Use the following wiring drawing (FIG. 7) to
configure an unbalanced audio connection.
GND
ININ+

Left Channel

GND
IN-

Right Channel

Unbalanced IN
(Jumper IN- to GND)

IN+
AUDIO IN
MIC OUT

GND
OUTOUT+

Microphone

Unbalanced OUT

FIG. 7 Wiring the rear AUDIO IN and MIC OUT for use with Unbalanced Audio

When using unbalanced audio for the AUDIO IN connector (FIG. 7), the "-" and the "GND" terminals
should be connected together and then connected to the GND of the unbalance audio signal. When
connecting to an unbalanced audio input from the MIC OUT connector (FIG. 7), wire the "+" terminal to
the signal input, and the "GND" terminal to the signal ground.

Wiring the NXA-AVB/ETHERNET for Balanced Audio
Professional audio equipment will often use balanced audio inputs and outputs, usually on 3-pin "XLR"
connectors. A balanced audio signal consists of a pair of wires carrying the audio signal in anti-phase
with each other (if one wire carries a positive voltage, the other carries an equal and opposite negative
voltage).
The advantage of balanced audio over unbalanced audio is its ability to reject external interference added
as the signal is carried over the wire. The receiving equipment takes the voltage difference between the
two wires as the input signal. Interference will usually get added to both wires equally, and so gets
cancelled by the receiving equipment.

1200V Modero Video Touch Panels

Touch Panel Accessories

The 3 wires used in a typical XLR lead are often referred to as Ground, Live (Hot) and Return (Cold).
"Live" and "Return" carry the "in-phase" and "out-of-phase" versions of the audio respectively. The pins
of the XLR plug/socket are as follows:
• X = Ground
• L = Live (Hot)
• R = Return (Cold)

When connecting the MIC OUT connector to a balanced audio input (FIG. 8), use all three audio
terminals (+, -, and GND), then connect the "+" terminal to the "live" signal, the "-" terminal to the
"return" signal, and the "GND" terminal to the ground signal.
Ground signal

GND
OUTOUT+

Return signal

Balanced OUT

Line signal

FIG. 8 Wiring the rear MIC OUT connector for use with Balanced Audio

Modero Table Top Cable (CA2250-50)
The Modero Table Top Touch Panels come with a standard 10' (3.048 m) Modero cable
(CA2250-50) that supports Ethernet, Audio/Video, and Power connections. The cable comes terminated
with two RJ45 connectors (Ethernet and Audio/Video) and a single 2-pin mini-Phoenix connector for
power.

FIG. 9 10 Foot Modero Table Top Cable

Product Specifications
Modero Table Top Cable Specifications
Dimensions (HWD):

• Length: 10 feet (3.048 m)

Connectors:

• Ethernet RJ-45 connector (White) routes Ethernet signals between the touch
panel and the NXA-AVB/ETHERNET Breakout Box.
• Audio/Video RJ-45 connector (Black) routes differential audio/video signals
between the touch panel and the box.
• 2-pin 3.5 mm mini-Phoenix power connector to route power from the external
breakout box to the target panel.

Included Accessories:

1200V Modero Video Touch Panels

• Modero Table Top Cable (CA2250-50)

Touch Panel Accessories

Modero Table Top Cable Specifications (Cont.)
Other AMX Equipment:

Note: All 1200V, VG-Series, and CV10 Table Top panels routing an
Audio/Video signal from a breakout box must use the appropriate number of
CAT5 Suppression Ferrites which are included as part of installation kits
accompanying your particular Modero panel.
Each of the following Installation Kits come with the appropriate number of
CAT5 Suppression Ferrites.
These ferrites must be installed onto their appropriate locations.
• Installation Kit for 12" and 17" NXD panels (KA2251-01):
- 2-pin mini-Phoenix connector (41-5025)
- Three Phillips-head screws (#4-20 x 0.250 Black) (80-0114-08)
- One CAT5 Suppression Ferrite (04-0014)
- Four Drywall clips (62-5924-05) and #6 -metal strips (80-0192)
• Installation Kit for 15" NXD panels (KA2251-02):
- 2-pin mini-Phoenix connector (41-5025)
- Three Phillips-head screws (#4-20 x 0.250 Black) (80-0114-08)
- Two CAT5 Suppression Ferrites (04-0014)
- Four Drywall clips (62-5924-05) and #6 -metal strips (80-0192)
• Installation Kit for 12" NXT panels (KA2251-03):
- 2-pin mini-Phoenix connector (41-5025)
- Three Phillips-head screws (#4-20 x 0.250 Black) (80-0114-08)
- Two CAT5 Suppression Ferrites (04-0014)
• Installation Kit for 15" and 17" NXT panels (KA2251-04):
- 2-pin mini-Phoenix connector (41-5025)
- Three Phillips-head screws (#4-20 x 0.250 Black) (80-0114-08)
- One CAT5 Suppression Ferrite (04-0014)
• Installation Kit for 10" NXT panels (KA2259-01):
- 2-pin 3.5 mm mini-Phoenix connector (41-5025)
- One CAT5 Table Top Suppression Ferrite (04-0014)
- One cylindrical CAT5 USB Mouse Suppression Ferrite (04-0018-SA)

Wiring information for the Modero Table Top cable
If your installation requires custom cable configurations, you can purchase bulk (non-terminated) cable
from Liberty Wire and Cable under the nomenclature "AMX Table Top Cable - Modero" (phone#:
(800) 530 8998 or +1-719-388-7518). When building a custom Table Top cable, please refer to the table
below to calculate the maximum length of the cable for your particular installation/setup.
Maximum Table Top Cable Lengths for Modero Panels
Panel Sizes:

7" Panel

10" Panel

12" Panel

15" Panel

17" Panel

39’ (11.89 m)

10’ (3.05 m)

15’ (4.57 m)

10’ (3.05 m)

Setup I: Using a panel without a battery base*:
Maximum cable length

150’ (45.72 m) 150’ (45.72 m) 49’ (14.94 m)

Setup II: Using a panel with a battery base*:
Maximum cable length

56’ (17.07 m)

25’ (7.62 m)

* The total Modero cable run from the 13.5 V power source.

* The total Modero cable run from the 13.5 V power source (12 VDC-compliant power supply).

1200V Modero Video Touch Panels

Touch Panel Accessories

FIG. 10 shows the top and cross-section views of the Table Top cable.
6 inches

3 inches

Red
3

Red

To Touch Panel

To Breakout Box

Connector 1 - used for Audio/Video (Black)

Connector 3 - used for Power

Connector 2 - used for Ethernet (White)
FIG. 10 Modero Table Top cable (top and cross-section views)

The following table provides the wiring information (color coding) for each of the three available cable
connectors on each side of the Modero Table Top Cable.
Modero Table Top Cable Wiring Table
Wire

Connector 1

Connector 2

Connector 3

White/Orange

Red

Orange/White

Black

White/Green

Blue/White

White/Blue

Green/White

White/Brown

Brown/White

The following figures provide a cross-section view (FIG. 11) and a description (FIG. 12) of the Modero
Table Top Cable:
Connector #1 & 2

Element #1
Binder
Element #2

Connector #3

Jacket
FIG. 11 Table Top Cable - cross-section view

1200V Modero Video Touch Panels

Touch Panel Accessories

DESCRIPTION:

9/PAIRS COMPOSITE CABLE CONSISTING OF: ELEMENT #1:
TWO 4/PAIR 24 AWG STRANDED TINNED COPPER,
POLYETHYLENE INSULATION, ELEMENT #2: 1/PAIR 18 AWG
STRANDED TNNED COPPER, PVC INSULATION AND FOIL
SHIELDED OVERALL PAPER BINDER AND FLEX-PVC JACKET.

ELEMENT #1:
2 X 4/PAIRS:
24 AWG STRANDED COPPER
CONDUCTOR: 24 AWG 7/32 TINNED COPPER; OD .024" NOMINAL
INSULATION:
.0075" WALL POLYETHYLENE; OD .039" NOMINAL
COLOR CODE: P1: WHITE/BLUE, BLUE
P2: WHITE/ORANGE, ORANGE
P3: WHITE/GREEN, GREEN
P4: WHITE/BROWN, BROWN
PAIR:
2 CONDUCTORS TWINNED LEFT HAND LAY
(TWISTED AT VARIED LAYS TO MINIMIZE CROSS TALK)
CABLE:
4/P CABLED LEFT HAND LAY (BLUE BINDER, ORANGE BINDER)
BINDER:
PAPER TAPE
ELEMENT #2:
1 PAIR: 18 AWG SHIELDED
CONDUCTOR: 18 AWG 16/30 TINNED COPPER; OD .046" NOMINAL
INSULATION:
.010" WALL PVC; OD .066" NOMINAL
COLOR CODE: BLACK, RED
DRAIN WIRE:
#22 7/30 TINNED COPPER
SHIELD:
ALUM/POLYESTER TAPE (FOIL SIDE IN)
FINAL ASSEMBLY:
BINDER:
JACKET:
COLOR:
DIAMETER:
MARKING:

TWO ELEMENT #1 & ELEMENT #2 CABLED ON COMMON
AXIS TO MINIMIZE DIAMETER
CLOTH TAPE 25% OVERLAP
.045" WALL FLEXIBLE PVC,
BLACK MATT
.375 INCHES NOMINAL
NONE

FIG. 12 Table Top Cable - Specification Elements

Each bundle of 4 twisted pairs includes a colored tape indicator for identification.

Installing CAT5 Suppression Ferrites
Before connecting the RJ-45 cables to the panel, install the necessary number of CAT5 Suppression
Ferrites (FIG. 13) to their appropriate locations. These ferrites come as part of the Installation Kits
mentioned in the previous Specification table (page 2). No tools are required for this installation.

Release the latch to
open the plastic
enclosure.

Insert the CAT5
cable and close
the enclosure.

Push down on the
enclosure until it
snaps closed.

FIG. 13 Installing the CAT5 Suppression Ferrites

All 1200V-Series, VG-Series, and Table Top CV10 panels require the installation of
an appropriate number of CAT5 Suppression Ferrites when they use an RJ-45 cable
to feed an A/V signal from the breakout box.

1. The CAT5 Suppression Ferrite is housed within a plastic enclosure (shown in FIG. 12) with a latch
release on one side. Pull to release the latch and open the enclosure.

1200V Modero Video Touch Panels

Touch Panel Accessories

2. Grasp the Black RJ-45 Audio/Video cable being connected to the panel. This end of the cable is
longer than the opposing end which connects to the breakout box (6 inches vs 3 inches). Refer to
FIG. 14 for more detailed information.
3. Insert the panel-end of the Black RJ-45 Audio/Video cable into the groove along the inside of the
enclosure.
The CAT5 Suppression Ferrites MUST be installed onto the cable connected to the
Modero’s Audio/Video RJ-45 connector (just behind the connector).

4. Snap the enclosure shut with the cable inside, and you’re done.
5. Repeat this process again only when installing an additional CAT5 Suppression Ferrite
(model specific).
3

2
1

Ferrite

e
rrit
Fe

To Touch
Panel
6 inches

Connector 1 - used for Audio/Video (Black)
Connector 2 - used for Ethernet (White)

Connector 3 - used for Power

FIG. 14 Ferrite connector location on Audio/Video RJ-45 cable

NXA-CFTP Compact Flash (FG2116-2x)
Every Modero panel is shipped with two factory default modules: an EXM Memory Module and a
Compact Flash card. These panels are shipped with a 256 memory module which is not
upgradeable.
The default 128 MB Compact Flash card is factory programmed with specific panel firmware and is the
only upgradeable memory component. This component can be ordered from AMX in several different
upgrade sizes (as listed in the following table):
Optional Compact Flash Memory Upgrades
Compact Flash:
NXA-CFTP256M - 256 MB Compact Flash card

(FG2116-23)

NXA-CFTP512M - 512 MB Compact Flash card

(FG2116-24)

NXA-CFTP1G - 1 GB Compact Flash card

(FG2116-25)

Upgrading the internal components involves opening the panel enclosure/outer housing to access the
internal circuit board, removing the existing part, and replacing them with the upgrade components, as
described in the following sections.

It is recommended that any upgrade of internal equipment be done simultaneously in
order to reduce the risk of damage to internal components.

1200V Modero Video Touch Panels

Touch Panel Accessories

NXA-PCI80211G Wireless Card (FG2255-04)
The 1200V-Series and VG-Series Modero touch panels can connect to an internal NXA-PCI80211G
compatible mini-PCI Wireless Card connected to two antennas (57-2250-10). All 1200-V and VG-Series
panels come factory installed only with the two antennas used for later connection to the optional
wireless card which is field-installable.

FIG. 15 NXA-PCI80211G mini-PCI Wireless Card

The NXA-PCI80211G card functions using a 2.4GHz bandwidth with a maximum data transfer rate of
54Mbps. This card is compatible with IEEE 802.11 standards such as: 802.11b and 802.11g.
The NXA-80211G allows the end-user to take advantage of larger bandwidth to utilize features such as:
wireless intercom, Motion JPEG, networked video, and standard wireless Ethernet communication to
both a NetLinx controller and networked computers. Please follow your particular Wireless Access
Point’s instruction manual for the correct procedures to setup either a secured or unsecured connection.
FCC Statement:
This device complies with Part 15 of the FCC rules. Subject to the following two conditions:
1. This device must not cause harmful interference and
2. This device must accept all interference, including interference that interferes with the
operation of this device.
Modifications not expressly approved by the manufacturer will void the user’s authority
to operate the equipment.
WARNING: This device has been evaluated and found to be compliant with the FCC Rules
for RF Exposure when the device is operated at a minimum separation distance from the
user and nearby persons. Operation of this device at closer distances should be avoided.

Certifications: FCCID: CWU-WN2301A, CE, EN 60950, EN 300 328,
and RSS 210

Product Specifications
NXA-PCI80211G Specifications
Dimensions (HWD):

• 0.02" x 2.13" x 4.66" (5.0 mm x 54.0 mm x 118.4 mm)

Weight:

• 1.05 oz (30g)

Description:

• Direct Sequence Spread Spectrum (DSSS)/CCK 802.11g Wireless mini-PCI
card with detachable antennas.

Features:

• Contains integrated power amplifier (PA) and low-noise amplifier (LNA)
• Diversity Antenna Connectors automatically select the best available signal
• Enhanced transmit and receive chains
• Field-installable
• Increased sensitivity and multipath tolerance
• Operates from 2.300-2.500 GHz
• Operate at ISM frequency bands (2.4GHz) with 54Mbps data rate
• Pre-configured to communicate with current AMX Wireless Access Points
• Support for IEEE 802.11b and 802.11g
• Wired Equivalent Privacy (WEP) 64-bit and 128-bit data encryption

1200V Modero Video Touch Panels

Touch Panel Accessories

NXA-PCI80211G Specifications (Cont.)
Antenna Type:

• Dual antenna connector

Availability:

• All 1200V-Series and VG-Series NXT Table Top panels come factory
configured for wireless communication. These NXT panels are all factory
installed with both the NXA-80211G wireless mini-PCI and 2 antennas.
• Optional to the following NXD panels:
- NXD-1200V
- NXD-1200VG
- NXD-1500VG
- NXD-1700VG

Bus Interface:

• mini-PCI card, TypeIIIB

Certifications:

• FCCID: CWU-WN2301A, CE, EN 60950, EN 300 328, and RSS 210and
FCCID (CWU-WN2301A)

Frequency Range:

• Using 802.11b & g communication:
- 2.412 ~ 2.462 GHz - North America
- 2.412 ~ 2.484 GHz - Japan
- 2.412 ~ 2.472 GHz - Europe ETSI
- 2.457 ~ 2.462 GHz - Spain
- 2.457 ~ 2.472 GHz - France

Media Access Technique:

• CSMA/CA with ACK

Modulation:

• Orthogonal Frequency Division Multiplexing (OFDM) / Complementary Code
Keying (CCK)

Network Architecture:

• Ad-hoc mode (Peer-to-Peer)
• Infrastructure mode

Network Standard:

• IEEE Compliant
• 802.11b and 802.11g

Operating Channels:

• Using 802.11b & g communication:
- 11: (Ch 1 - 11) - North America
- 14: (Ch 1 - 14) - Japan
- 13: (Ch 1 - 13) - Europe ETSI
- 2: (Ch 10 - 11) - Spain
- 4: (Ch 10 - 13) - France

Operating Environment:

• Temperature: 0°C ~ 55°C (32°F to 131°F) (operating) and
-20°C ~ 70°C (-4°F to 158°F) (storage)
• Humidity: (non-condensing) 5% ~ 90% RH (operating) and
(non-condensing) 5% ~ 95% RH (storage)

Operating Voltage:

• 3.3V + 5% I/O supply voltage

Power Consumption:

• @ 802.11b communication:
- RX: 300 mA
- TX: 64 mA
- Sleep: 12mA
• @ 802.11g communication:
- RX: 330 mA
- TX: 575 mA
- Sleep: 12mA

Radio Data Rate:

1200V Modero Video Touch Panels

• 802.11g compliant: 1, 2, 5.5, 11 (DSSS/CCK); 6, 9, 12, 18, 24, 36, 48, and 54
(OFDM) Mbps data rates

Touch Panel Accessories

NXA-PCI80211G Specifications (Cont.)
Receiver Sensitivity:

• Using 802.11b communication:
1 Mbps: -86 dBm (max)
2 Mbps: -84 dBm (max)
5.5 Mbps: -83 dBm (max)
11 Mbps: -80 dBm (max)
• Using 802.11g communication:
1 Mbps: -86 dBm (max)
2 Mbps: -84 dBm (max)
5.5 Mbps: -83 dBm (max)
11 Mbps: -80 dBm (max)

Security:

• 64-bit and 128-bit WEP

Availability:

• All 1200V-Series and VG-Series NXT Table Top panels can be field upgraded
for wireless communication using the optional NXA-PCI80211G mini-PCI
card.
• Optional to the following NXD panels:
- NXD-1200V
- NXD-1200VG
- NXD-1500VG
- NXD-1700VG

Installation and Upgrade of the Internal NXT Components
Upgrading the components within the Table Top panel involves removing the outer housing (with
speaker plate), removing and/or installing an existing component, and then placing the outer housing
back onto the NXT panel, as described in the following sections.

Do not use Ethernet cables containing mounting boots. These boots could make
removal of the Ethernet connectors (from the panel) difficult and cumbersome.

Step 1: Remove the existing NXT Outer Housing
1. Carefully detach all connectors from the rear of the touch panel and then gently place the touch
panel LCD facedown onto a soft cloth to expose the under-side of the base (FIG. 16). This step
helps prevent scratching of the LCD.
2. Tilt the base forward so that both the bottom surface and Housing Screws are easily accessible and
then carefully remove the four plastic adhesive feet.
Reference the location of the four plastic adhesive "feet". Once the outer housing is
placed back onto the panel, these "feet" must be placed back in their original
locations so they can fit into their provided openings on a Battery Base.

3. While holding the outer housing and base plate at a 45° (to prevent it from sliding), use a grounded
Phillips-head screwdriver to remove the eight Housing Screws.

1200V Modero Video Touch Panels

Touch Panel Accessories

Base plate
Unscrew these
eight Housing
Screws to remove
the circuit board
housing

Outer housing

45°

Hinge Brackets (2)

DO NOT
REMOVE
these screws
They secure
the speakers
to the main
board

FIG. 16 Location of the attachment screws underneath an NXT panel base

4. Rotate the panel back over (while gripping the entire unit with outer housing) and rest the base on a
flat surface.
5. Gently tilt the LCD backward to a 45° angle.
6. In a single motion, carefully pull the outer housing up and then out (away from the LCD panel) to
expose the internal circuit board.
7. Unscrew the Stereo Output nut from the Stereo Output jack.
8. Firmly grab the existing connector plate and slide it up and away from the base.
Step 2: Install the 802.11g mini-PCI Wireless Card
1. Discharge any static electricity from your body by touching a grounded metal object.
2. Locate the mini-PCI card connector on the main board (FIG. 17 and FIG. 18).
Outer Housing

NXA-PCI80211G
wireless card
location
I/O connector
plate
Eight Housing
Screws

Compact Flash card

FIG. 17 Location of the NXA-PCI80211G wireless card on the NXT board

1200V Modero Video Touch Panels

Touch Panel Accessories

FIG. 18 Location of the mini-PCI card connector on main board

3. Carefully remove the gold-tipped terminal ends of the antenna from their factory default connectors
on the main board. The antenna is secured at this location to restrict its movement prior to
connection to a wireless card.
4. Firmly grasp the NXA-PCI80211G mini-PCI card (from the edges) and insert the pins (at a 25°
angle) into the opening on the connector (FIG. 19).
5. While maintaining the 25° angle alignment on the new module, push it in firmly until the contact
pins are completely inside the connector and the card "snaps" into place (FIG. 19).
6. Push the card downward (to the main board) until the side braces snap atop the NXA-PCI80211G
and hold it in place.

Antennas connectors

Connection point
between the braces and
the mini-PCI card

FIG. 19 Installation of the mini-PCI card connector on main board

7. Locate the terminal ends of the antennas and apply downward pressure to "snap" them onto their
gold-tipped counterparts on the mini-PCI card (FIG. 19). Carefully push down on each connector to
verify it is securely joined to the card.
It is recommended that any upgrade of internal equipment be done simultaneously in
order to reduce the risk of damage to internal components.

1200V Modero Video Touch Panels

Touch Panel Accessories

Step 3: Install the Compact Flash Memory Card upgrade
1. Discharge any static electricity from your body by touching a grounded metal object and then locate
the existing Compact Flash card (factory-shipped with 128 MB) on the main board (FIG. 20 for
Table Top panels and FIG. 23 for Wall Mount panels).
Outer Housing

NXA-PCI80211G
wireless card

I/O connector
plate
Eight Housing
Screws

Compact Flash card

FIG. 20 Location of the Compact Flash card and I/O plate on NXT

2. Insert the tip of a grounded flat-head screwdriver into one of the card removal grooves (located on
either side of the existing card), and gently pry the card out of the slot (FIG. 21). Repeat this process
on the opposite card removal groove. This alternating action causes the card to "wiggle" away from
the on-board connector pins.
Card removal
grooves

On-board Compact
Flash connector (with pins)
Insert with arrow
facing towards the pins

Connector opening

FIG. 21 Removing/installing a Compact Flash Memory card

3. Grip the old card by its sides and then carefully pull it out of the slot.
4. Remove the new CF memory card from it’s anti-static bag.

1200V Modero Video Touch Panels

Touch Panel Accessories

5. Grip the sides of the new CF memory card and firmly insert it into the slot opening (with the arrow
facing towards the pins) until the contact pins are completely inside the flash card and it is then
securely attached to the pin sockets.
6. To complete the upgrade process, close and resecure the panel enclosure using the procedures in the
following step.

Any new internal card upgrade is detected by the panel only after power is cycled.

Step 4: Close and Resecure the NXT Panel Enclosure
1. Obtain the I/O connector plate and slide it back into position (FIG. 20).
2. Resecure the Stereo Output nut back onto the new Stereo Output jack onto the I/O plate.
3. With the components securely installed, tilt the LCD back to a 45° and gently slide-on the outer
housing (towards the LCD) until the it is aligned over the installation holes and the tilt bracket
prevents any further forward movement (FIG. 16).
4. Gently press down on the housing (toward the base) until it is securely positioned over the circuit
board and covers base.

Use caution when re-installing the outer housing. Improper re-installation can cause
damage to the internal speakers.

5. While holding the outer housing and base plate in place, turn the panel back over until the LCD lies
facedown on a soft cloth and the under-side of the base is exposed.
6. Insert and secure the eight Housing Screws (using a grounded Phillips-head screwdriver) into their
respective locations (FIG. 16).
7. Replace any adhesive plastic "feet" that might have been removed during the removal process of the
outer housing. These "feet" must be placed back onto their original locations so they can fit into
their provided openings on the Battery Base.
8. Grasp both the LCD and housing and then rotate the entire unit back onto a flat surface.
9. Insert all connectors and apply power.

Installation and Upgrade of the Internal NXD Components
Upgrading the components within a WallMount panel involves removing the rear plastic outer housing
(back box), removing and/or installing an existing component, and then placing the back box back onto
the NXD panel, as described in the following sections.

Step 1: Remove the existing NXD Outer Housing
1. Carefully detach all connectors from the side of the touch panel and remove the front magnetic
faceplate from the NXD unit by firmly gripping the faceplate and pulling outwards, while applying
a small amount of pressure to remove it from the main unit.
2. Place the LCD facedown onto a soft cloth to expose the under-side of the unit (FIG. 22). This step
helps prevent scratching of the LCD.
3. Unscrew the Stereo Output nut from the Stereo Output jack.

1200V Modero Video Touch Panels

Touch Panel Accessories

4. Remove the I/O connector plate by using a grounded Phillips-head screwdriver to remove the two
screws and slide the I/O connector plate away from the back box housing.

DO NOT
REMOVE
these
panel
securing
screws

DO NOT REMOVE
these panel
securing screws

Unscrew these four Housing Screws
to remove the back box. These make direct
contact with the black outer housing.
FIG. 22 Location of the securing screws on an NXD panel

DO NOT REMOVE THE PANEL SECURING SCREWS. These screws secure the
LCD to the metallic casing.

5. Unscrew the four pan-head Housing Screws from the rear of the NXD unit (FIG. 22) and gently
remove the outer housing. These four screws secure the back box to the internal panel casing.
Step 2: Install the new 802.11g mini-PCI Wireless card (NXD)
1. Complete the procedures outline within Step 2: Install the 802.11g mini-PCI Wireless Card section
on page 19 and then continue with the following step.
Step 3: Install the new Compact Flash Memory card (NXD)
1. Complete the procedures outline within Step 3: Install the Compact Flash Memory Card
upgrade section on page 21 and then continue with the following step.

1200V Modero Video Touch Panels

Touch Panel Accessories

Four Pan-head
Housing
Screws

Outer Housing
I/O connector
plate

NXA-PCI80211G
wireless card
location

Compact Flash card

FIG. 23 Location of the Compact Flash card and I/O plate on NXD

Step 4: Close and Resecure the NXD Panel Enclosure
1. With the components securely installed, gently place the outer housing back onto the metallic panel
casing (with the connector opening on the right-side of the panel) and align the four pan-head
Housing Screw holes along the edges of the outer housing.

Use care not to bend or damage any antenna connections while replacing the outer
housing.

2. Insert and secure the four pan-head Housing Screws into the pre-drilled holes along the edges of the
NXD unit by using a grounded Phillips-head screwdriver.
3. Reinstall the I/O connector plate by aligning all connectors to their respective locations.
4. Secure the I/O connector plate using a grounded Phillips-head screwdriver and then twist the Stereo
Output nut back into the Stereo Output jack.

1200V Modero Video Touch Panels

Touch Panel Accessories

NXT-BP Power Pack (FG2255-10)
The NXT-BP Power Pack (FIG. 24) is a rechargeable Lithium-Ion "smart" battery used to provide power
to the NXT Modero panel through the NXA-BASE/B Battery Base. This battery incorporates an
on-board battery life indicator. The NXT-BP battery can be charged through either the base (when
connected to the Modero panel) or through an optional NXT-CHG Modero Power Station.
Extra NXT-BP Power Packs can be purchased separately as an optional accessory.

FIG. 24 NXT-BP Power Pack

Product Specifications
NXT-BP Specifications
Dimensions (HWD):

• 0.69" x 3.50" x 5.81" (1.75 cm x 8.89 cm x 14.76 cm)

Power (Voltage):

• 11.1 Volts (nominal)

Weight:

• Single NXT-BP Power Pack: 1.0 lbs (0.45 kg)

Features:

• Battery Usage: 4 to 8 hours (time is usage dependant)
• Charge Capacity: 6300mAh

Operating / Storage
Environment:

• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage/Discharge Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH

NXA-BASE/B Battery Base Kit (FG2255K)
The NXA-BASE/B Battery Base is a Modero accessory that allows the Modero Table Top touch panels
(NXT) to function off the collective charge of two internally connected NXT-BP batteries (FG2255-10).
The base provides both power and battery information to the panel via the panel interface connector
(FIG. 25). The NXT-BP batteries can be charged through either the base (only when connected to the
NXT touch panel) or through an optional NXT-CHG Modero Power Station.
Panel Interface
Connector

NXA-BASE/B
Battery Base

NXT-BP
Battery Pack

FIG. 25 NXA-BASE/B and NXT-BP combo

1200V Modero Video Touch Panels

Touch Panel Accessories

This base also comes as part of a NXA-BASE/B Kit that contains one (1) battery base and two batteries.
The accompanying batteries can be charged through either the base or optional NXT-CHG Battery
Charger (FG2250-50). Refer to the Installing the NXA-BASE/B to an NXT Modero Panel section on
page 27 for more detailed installation and usage instructions.

Product Specifications
NXA-BASE/B Specifications
Dimensions (HWD):

• 1.13" x 8.63" x 11.81" (2.86 cm x 21.91 cm x 30.00 cm)

Power Requirements:

• 2.7 A @ 12 VDC (max power draw while charging)

Weight:

• Base unit: 1.25 lbs (0.567 kg)
• Base and 2 batteries: 3.23 lbs (1.47 kg)

Features:

• Charge time for two depleted batteries ~ 5 - 8 hours (when NXT panel is in
Sleep mode)
• Must be connected to the Modero unit utilizing a 12 VDC-compliant power
supply

Operating / Storage
Environment:

• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH

Other AMX Equipment:

• NXT-CHG Kit (FG2250-50K):
Charger (FG2250-50) and 2 NXT-BP batteries (FG2255-10)
• NXT-BP battery pack (FG2255-10)
• NXT-CHG battery charger (FG2250-50)

It is recommended to fully charge the batteries before their initial use.

Checking the NXT-BP battery charge
1. Press the Battery Life Indicator button (FIG. 26) once to illuminate the Battery Life LEDs and
display the percent charge remaining on the battery (this indication lasts a few seconds).

Battery Life (Charge) Display
Battery Life Indicator button

FIG. 26 NXT-BP (showing Battery Life Indicator button and charge)

2. Repeat the above step for each NXT-BP battery.
3. Charge the NXT-BP battery by either inserting it into the battery base or from within the optional
NXT-CHG charger (which can sequentially charge up to two batteries).
If the 25% LED is blinking, this indicates there is less than 5% of a charge remaining
on the battery.

1200V Modero Video Touch Panels

Touch Panel Accessories

Installing the NXA-BASE/B to an NXT Modero Panel
The battery base must be installed onto the NXT panel without any NXT-BP batteries.

1. Power Off the panel before attempting to use the NXA-BASE/B.
2. Place the empty battery base onto a flat/level surface.
3. Verify the alignment of the Panel Interface connectors between the panel (male connector) and base
(female connector) (FIG. 27).
Battery Compartment
pulls outwards

Captive fasteners
(secure base to
panel)

Panel Interface
connector (female)
Alignment
pegs
FIG. 27 NXA-BASE/B showing Panel Interface and connector locations

4. Carefully place the Modero panel over the base alignment pegs (FIG. 27 and FIG. 28).
The battery base cannot be "hot-swapped". A panel receiving power through a
connected 12 VDC-compliant power supply cannot have a battery base installed onto
the bottom of the panel while powered. POWER OFF the panel before installing the
NXA-BASE/B.
"Hot swapping" could damage the base and cause it not to be recognized by the
panel.

5. Gently apply downward pressure until the panel is securely mounted to the battery base (FIG. 28).
6. Firmly grip both the panel (from the side) and battery base (from below) together.
7. Gently place the touch panel LCD facedown onto a soft cloth (this prevents scratching of the LCD
while the battery base is being secured).
8. Locate the captive fasteners on the underside of the battery base by angling the base combo slightly
forwards.
9. Secure each captive fastener head using a grounded flat-head screwdriver until the NXA-BASE/B is
securely attached to the underside of the NXT Modero touch panel.
10. Firmly grip the panel LCD/base combo and gently rotate the unit back onto the base.

1200V Modero Video Touch Panels

Touch Panel Accessories

Bottom view

Top view

Interface
connector
(male)

Panel Interface
connector
(female)

Alignment
pegs

Captive
fasteners

FIG. 28 NXA-BASE/B shown aligning with NXT panel

Installing an NXT-BP into the NXA-BASE/B
The battery base does not directly connect to a power supply, but rather receives its power directly from
the Modero panel, through the Panel Interface connector.
Remove any connectors from the rear of the Modero NXT panel before continuing
with the installation of the batteries. Power can only be supplied after the batteries
have been installed.

1. With the panel mounted on the battery base, open the battery compartment (FIG. 29) by pulling the
handle outwards. This compartment houses two NXT-BP batteries.
NXT-BP Battery #2
Battery
Connectors
Interface
connector

Battery
Connector
Port
FRONT
Battery #2
slot
NXT-BP Battery #1
Battery
Compartment
FIG. 29 Battery installation procedure

1200V Modero Video Touch Panels

Touch Panel Accessories

2. Install the NXT-BP battery. label-side down.
3. Align the battery connectors with the corresponding battery connector port (located inside the
battery compartment), as shown in FIG. 29.
4. Insert the NXT-BP battery until the connectors securely fit into the battery connector port.
5. Repeat steps 2 through 4 for the other battery.
6. Apply a small amount of pressure to close the battery compartment until the compartment latches.
After a few seconds, the panel will turn On and the AMX logo will appear (indicating the
panel is receiving power.

Charging the NXT-BP batteries with the NXA-BASE/B
1. Follow the procedures from the previous sub-section to attach the NXT touch panel to the
NXA-BASE/B.
2. Insert each battery into the battery compartment shown in FIG. 29.
3. Insert a 2-pin connector from a power supply to the rear PWR connector on the NXT Modero panel.
The charge status bargraph indicators, on the Battery Base page, indicate when the batteries
are fully charged.

The NXA-BASE/B will only charge batteries when the NXT panel is in Sleep mode.

NXT-CHG Battery Charger Kit (FG2255-50K)
The NXT-CHG Kit includes one charger and two batteries. The optional NXT-CHG Modero Power
Station (FIG. 30) is a two-slot, stand-alone battery charger that can be used to recharge up to two
NXT-BP batteries. The batteries are charged in the order they are inserted into the charger. The
NXT-CHG Slot 1 has the feature of being able to completely discharge and recharge (recalibrate) a
battery.

Battery Life indicator

NXT-BP Modero Power Pack (battery)
NXT-CHG Modero Power Station (charger)
FIG. 30 NXT-CHG Kit (consists of one NXT-CHG charger and two NXT-BP batteries)

1200V Modero Video Touch Panels

Touch Panel Accessories

Product Specifications
NXT-BP and NXT-CHG Specifications
Dimensions (HWD):

• 1.13" x 8.63" x 11.81" (2.86 cm x 21.91 cm x 30.00 cm)

Power Requirements:

• NXT-BP Battery Voltage - 11.1 Volts
• NXT-CHG: 90 - 264 VAC, 47-63 Hz, Single Phase
(using the included 24 VDC power supply)

Weight:

• 0.57 lbs (0.26 kg)

Features:

• Charge time for two depleted batteries: ~ 5 hours
• Charge Rate: 2.5 A @ 12 VDC
• 2-Bays: Sequential charging
• LED: One LED indicator in front of each bay which conveys the status of that
bay. Refer to the Reading NXT-CHG LED Indicator section for more
information.
• Recalibration pushbutton (located between the bays): Initiates recalibration
sequence in the left bay only.
• Recalibration Time: less than 9 hours

Other AMX Equipment:

• NXT-CHG Kit (FG2250-50K):
- 1 charger and 2 NXT-BP batteries
• NXT-BP battery pack (FG2255-10) (additional)

The batteries are charged in the order they are inserted into the NXT-CHG. SLOT 1 of the
NXT-CHG has the ability to completely discharge and recharge (recalibrate) a battery.

Recalibration improves the reporting accuracy of the battery charge back to the
Modero panel.

Powering the NXT-CHG
The NXT-CHG Smart Battery Charger uses an included power supply to charge inserted batteries.

1. Connect the rear of the NXT-CHG to the power adapter.
2. Connect the power adapter to the provided power cord (with plug).
3. Provide power to the unit by connecting the power cord (with plug) into a power outlet that meets
the requirements outlined in the Specifications section for the NXT-CHG.
Reading NXT-CHG LED Indicator
FIG. 31 shows the components on the NXT-CHG Smart Battery Charger.

Slot 1
(recalibration)
Slot 2
Slot 1
LED
Slot 2
LED
Recalibrate
Pushbutton
FIG. 31 Component locations on the NXT-CHG

1200V Modero Video Touch Panels

Touch Panel Accessories

There is one LED indicator on the front of each battery slot that indicates the status of that slot. The blink
patterns for these LEDs are described in the following table:
• Off:

No battery detected.

• Green Flashing:

Fast charging.

• Green Solid:

Fully charged.

• Yellow Flashing:

Recalibration in process.

• Yellow/Green:

Recalibration complete.

• Yellow Solid:

Standby (waiting for other battery to charge).

• Red Flash:

Error (problem with either the battery connection to the internal slot, or with
the battery itself).

Charging the NXT-BP batteries using the NXT-CHG
1. Review the Checking the NXT-BP battery charge section on page 26 to confirm the percentage of
charge remaining on the batteries.
2. Provide power to the charger (as outlined in the Powering the NXT-CHG section on page 30).
3. Align the battery connector with the corresponding charge slot within each of the two NXT-CHG
slots.
4. Firmly insert the battery into the desired slot until the battery is both securely located within the slot
and there is activity from the corresponding Slot LED. Refer to the Reading NXT-CHG LED
Indicator section on page 30 section for LED information.
Recalibrating the batteries
The recalibration process increases the accuracy of the battery charge level. Recalibration of the batteries
is only done upon request from the Modero on-screen Battery Base page. Refer to the Battery Base
Page section on page 102 for more detailed Battery Base page information.

Recalibration can only be done with Slot 1 on the NXT-CHG.

1. Place the selected battery securely into Slot 1 (left slot) until there is activity on the Slot 1 LED.
2. Push the Recalibration pushbutton (located between the two slots) to initiate recalibration in the
left bay only.

1200V Modero Video Touch Panels

Touch Panel Accessories

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

Installation Procedures: NXD-1200V Panels
NXT panels are mounted onto flat (horizontal) surfaces in either a stand-alone or combo (NXT atop an
NXA-BASE/B battery base) configuration. NXD panels are installed into either a pre-wall surface (using
a CB-TP12 conduit/wallbox) or a solid surface (using either solid surface or drywall screws).

It is recommended that if you are planning on upgrading your panel components
(flash card and wireless), you do so before beginning any panel installations.

Unpacking the Panel
1. Inspect and confirm the contents of the shipment box to verify that you have all specified parts.
Refer to the Specifications sections on page 2 for more information about included accessories and
other AMX equipment.
2. Carefully remove the panel from the shipping box.
3. Carefully peel the protective plastic cover from the LCD.
If the protective plastic LCD cover is not removed, the panel may not respond
properly to touch points on the LCD or allow proper screen calibration.

Installing the Internal Components
Installation of the internal components such as the upgraded Compact Flash memory and
NXA-PCI80211G Wireless card are described in detail within the following sections:
Step 2: Install the 802.11g mini-PCI Wireless Card section on page 19.
Step 3: Install the Compact Flash Memory Card upgrade section on page 21.

Upgrading to the MB-TP12 VESA Mounting Kit
Upgrading the existing back box with the new VESA Mounting Kit on the 12" (FG031-50) panel
requires 3 main processes:
Removing the pre-existing back box and installing the new VESA back box.
Threading cables through the strain relief grommet opening in the rear plastic cover.
Finalizing the installation of the NXD (with VESA back box and cables) into the plastic cover,
securing both components, and finalizing the strain relief grommet installation.
Only overall dimensions and FG product numbers are different.
The new MB-TP Universal VESA Mounting Box uses a standard VESA installation
pattern of 75 mm between holes. VESA mounts that conform to this pattern can be
used on the MB-TP Housing.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

Removing the Original Modero Back Box
1. Detach all connectors from the side of the touch panel.
2. Remove the magnetic faceplate from the NXD unit by gripping the faceplate and pulling outwards
while applying a small amount of pressure to remove it from the main unit.
3. Place the LCD face-down on a soft cloth to expose the back of the panel and prevent scratching of
the LCD.
4. Unscrew the Stereo Output nut from the Stereo Output jack.
5. Remove the I/O connector plate by using a grounded Phillips-head screwdriver to remove the two
screws and slide the I/O connector plate away from the back box housing.
6. Remove the four pan-head Housing Screws from the rear of the NXD unit (FIG. 32). These screws
secure the back box to the internal panel casing.

DO NOT
REMOVE
these
panel
securing
screws

DO NOT REMOVE
these panel
securing screws

Unscrew these four Housing Screws
to remove the back box. These make direct
contact with the black outer housing.
FIG. 32 Location of the attachment screws on the NXD back box

DO NOT REMOVE THE FOUR PANEL SECURING SCREWS. These screws secure
the LCD to the metallic casing underneath.

7. Lift the back box housing to separate it from the internal panel casing.
Installing the MP-TP12 Back Box
1. Unscrew the four pan-head Housing screws (#8-32) from the MP-TP12 rear plastic cover.
2. Gently place the MP-TP12 back box over the internal panel casing (with the cable routing hole on
the right-side of the panel).
3. Re-install and secure the four pan-head Housing Screws into their pre-drilled holes along the edges
of the MB-TP12 back box (FIG. 33) and secure them using a grounded Phillips-head screwdriver.
4. Place the I/O connector plate back over the connector opening and align the connector locations.
5. Resecure the I/O connector plate (using a grounded Phillips-head screwdriver) and resecure the
Stereo Output nut on the Stereo Output jack.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

DO NOT REMOVE
Twelve
#6-32
securing
screws
MB-TP12 back box

Connector
Opening
Strain relief grommet (Clip facing up)
Rim of the strain relief grommet
should lie flush against enclosure

Securing
hole locations
(3 on each side)

Internal panel casing

Four (pan-head) Housing Screws
Rear plastic cover
Four (#8-32) screws
FIG. 33 Location of the attachment screws on the NXD back box and VESA housing

Cable Installation for the MP-TP12 Back Box
1. Connect the cable connectors (RJ-45, Ethernet, and any other audio/video wiring) to their respective
locations along the side of the touch panel.
2. Thread the incoming cables through the strain relief grommet opening on the rear plastic cover
(FIG. 33).
Finalizing the installation
1. Gently place the rear plastic cover over the NXD panel (with LCD and MB-TP12 back box).
2. Insert the protruding cables, coming out from the opening on the rear plastic cover, into the open
strain relief grommet.
3. Allow some slack/length on these cables as a service loop. This service loop provides enough cable
length so you can later remove the NXD (with connected cables) from the rear plastic cover.
VERIFY THE LENGTH AND LOCATION OF THE INSERTED CABLES. ONCE THE
STRAIN RELIEF GROMMET IS CLOSED, IT IS DIFFICULT TO RE-OPEN.

4. Carefully apply pressure to close the strain relief grommet over the desired cable location.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

Verify the Strain Relief Grommet is securely closed over the cables and the clip is
facing the correct direction (upwards). The process of securing the strain relief
grommet may require the use of pliers. Also verify the length and location of the
inserted cables. Once the strain relief grommet is closed, it is difficult to re-open.

5. Firmly push the Strain Relief Grommet into the opening (toward the inside) until the rim is securely
flush against the back of the rear plastic cover (FIG. 33).
6. Securely grasp both sides of the NXD panel (with LCD, MB-TP12 back box, and attached cables),
rotate the entire unit over, and lie it on a flat level surface.
7. Note the available mounting contact surface area on the rear plastic cover of the MB-TP12
(FIG. 34). This area represents the space available for use with a VESA connector plate.

.80[20MM]

2.52[64MM]

2.61[66MM]

3.55[90MM]
FIG. 34 MB-TP12 Mounting contact surface area

8. Insert and secure the twelve #6-32 securing screws into their pre-drilled holes along the edges of the
NXD unit (FIG. 33). This step secures the NXD unit to the rim of the rear plastic cover.
9. Align a VESA mount connector (purchased separately) to the four #8-32 screw holes on the back of
the rear plastic cover (FIG. 33).
10. Insert the four provided #8-32 screws through the VESA mount’s four holes and then into the
pre-drilled holes on the rear plastic cover.

When installing a VESA mount to the rear plastic cover, use only the AMX provided
#8-32 screws.

11. Secure these four #8-32 screws to the rear plastic cover by using a grounded Phillips-head
screwdriver. This step secures the VESA mount to the rear of the panel.
Refer to your particular VESA mount manufacturer’s installation procedures for further surface
mounting procedures.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

Rear plastic cover (rear view)

Rim of the strain relief grommet
should lie flush against enclosure

CLIP FACING UP

VESA mount connection location
(USE ONLY AMX PROVIDED #8-32 screws)
FIG. 35 Installation of grommet into the rear plastic enclosure

Pre-wall Installation of the Conduit Box
Wall Mount panels (NXDs) are contained within a metallic outer housing (back box). This back box is
not removed when installing the NXD into a conduit box (CB-TP12). The back box is only removed to
either gain access for the replacement of the Memory/Compact Flash or upgrade the unit with an MB-TP
Universal VESA Mounting Kit.
INSTALLER: LEAVE A GAP BETWEEN THE STUD AND CONDUIT BOX TO
ACCOMMODATE THE DRYWALL SHEETROCK. This gap allows the installation of
the drywall/sheetrock after the conduit box has been installed.

The CB-TP12 conduit wallbox is an optional metallic box that is secured onto stud beams prior to the
installation of a solid surface. Installation procedures and configurations can vary. This section describes
the installation procedures for the most common installation scenario.

1. Fasten the CB-TP12 to a stud through the stud fastening holes, located on the inside of the conduit
box (FIG. 36), by using either nails or screws.
2. Remove any necessary wiring knockouts from the (optional) conduit box (C in FIG. 36) where the
necessary cables are threaded through for connection to the touch panel.
3. Thread the incoming RJ-45, Ethernet, and any other audio/video wiring through the knockouts.
Refer to the Wiring Guidelines for the 1200V Panels section on page 45 for pinout descriptions.
Leave enough slack in the wiring to accommodate any re-positioning of the panel.
4. Install the drywall/sheetrock before inserting the main NXD unit into the CB-TP12.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

Stud
Knockouts should be located on the left-side of the
conduit box, alongside the connectors
Drywall/
sheetrock

CB-TP Conduit Wallbox

Stud fastening holes

Use the four #4-40
Mounting Screws to
secure the NXD to the
conduit box at these
locations
Mounting tabs
for NXD panel should
be flush with the outside of the sheetrock

FIG. 36 Screw locations for conduit box attachment in a pre-wall installation

Installation of the NXD Touch Panel
The NXD panel can be installed either directly into the (optional) CB-TP12 or other solid surface
environment using the two different mounting options: drywall clips or solid surface screws. The
following sections describe mounting the touch panel directly into a pre-wall installed conduit box, a
solid surface or drywall, and optional NXA-RK Rack Mount Kit.

Installing the NXD panel within a Conduit Box
The conduit box must be mounted prior to continuing this section. Refer to the procedures in the
Pre-wall Installation of the Conduit Box section on page 37 for detailed pre-wall installation
instructions. Verify that all necessary cables have been threaded through the knockouts on the conduit
box and the connections have been tested prior to installation of the NXD panel.

1. Remove the magnetic faceplate/bezel (A in FIG. 37) from the main NXD unit (B in FIG. 37) by
gripping the faceplate and pulling with gentle outward force.
2. Verify the incoming RJ-45, Ethernet, USB, and any other audio/video cables have been properly
threaded through the wiring knockouts (from their terminal locations) on the conduit box.
Leave enough slack in the wiring to accommodate any re-positioning of the panel.
3. Connect all data and power wiring connectors to their corresponding locations along the side of the
(un-powered) NXD touch panel.
Verify the terminal end of the power cable is not connected to a power supply before plugging
in the 2-pin power connector.
The USB connectors can be from either a USB extension cable, or a wireless USB RF
transmitter.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

Stud
Cable
knockouts

C - Optional CB-TP
conduit/wallbox

Mounting Tab

Install the four #4-40
screws into the places
indicated

Installed flush
against the
finished wall
surface

SURFACE

Do not use these
tabs to mount
the conduit /wallbox
These are ONLY used to
secure the main unit to the CB

A - Faceplate
(bezel)

B - Main NXD unit consists of
the touch panel and backbox housing

FIG. 37 Wall Mount panel installation configuration for pre-existing conduit/wallbox in a pre-wall construction

Don’t disconnect the connectors from the touch panel. The unit must be installed with
the attached connectors before being inserted into the conduit box.

6. Carefully slide the main unit (B in FIG. 37) into the conduit box, so the Mounting Tabs lie flush
against the conduit box (C in FIG. 37).
7. Insert and secure the four securing #4-40 Mounting Screws into their corresponding holes located
along the sides of the NXD (FIG. 36 and FIG. 37).
8. Place the magnetic faceplate (A in FIG. 37) back onto the main NXD unit (B in FIG. 37).
Make sure to align the Microphone, Light, and PIR Motion sensor locations to their respective
openings on the front bezel/faceplate.
9. Reconnect the terminal RJ-45, Ethernet, USB, and any optional audio/video wiring to their
respective locations (outside the conduit box) on either the NXA-AVB/ETHERNET Breakout Box,
Ethernet port, or NetLinx Master.
10. Reconnect the terminal power connector on the 12 VDC-compliant power supply and apply power.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

Installing the NXD into drywall using Expansion Clips
Expansion clips are mounted through the four oval holes located at the top and bottom of the panel. As
the screw is tightened, the clip bends toward the insertion hole and into the wall. This bending creates a
"grip" on the wall by either pressing onto the wall or by securing the drywall between the housing and
the drywall clip.
The most important thing to remember when mounting the NXD is that the outer frame (Mounting Tabs)
must be installed flush against the mounting surface.

1. Prepare the area by removing any screws or nails from the drywall before beginning the cutout
process.
2. Cut out the surface for the 12-inch Wall Mount using the dimensions shown in FIG. 38. Be sure to
cut out the four notches along the top and bottom areas to accommodate the four drywall expansion
clips (provided).

CUTOUT

FRONT BEZEL

FIG. 38 NXD-1200V 12-inch Wall Mount panel dimensions using expansion clips

3. Remove the magnetic faceplate/bezel (A in FIG. 39) from the main NXD unit (B in FIG. 39) by
gripping the faceplate and pulling with gentle outward force.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

4 notches are
required if the
unit is installed in
drywall using the
four (4) provided
drywall expansion
clips

Install the four drywall
clip sets (included)
into these holes

Mounting Tab

A - Faceplate
(bezel)

B - Main NXD unit consists of
the touch panel and housing

FIG. 39 Wall Mount panel (NXD) installation configuration for drywall surfaces

4. Thread the incoming RJ-45, Ethernet, USB, and any other audio/video wiring (from their terminal
locations) through the cutout opening. Refer to the Wiring Guidelines for the 1200V Panels section
on page 45 for pinout descriptions.
Leave enough slack in the wiring to accommodate any re-positioning of the panel.
5. Connect all data and power wiring connectors to their corresponding locations along the side of the
(un-powered) NXD touch panel.
Verify the terminal end of the power cable is not connected to a power supply before plugging
in the 2-pin power connector.
The USB connectors can be from a either a USB extension cable, or a wireless USB RF
transmitter.

6. Test the incoming wiring by attaching the panel connections to their terminal locations and applying
power. Verify the panel is receiving power and functioning properly to prevent repetition of the
installation.
7. Disconnect the terminal end of the power cable from the connected power supply.
Don’t disconnect the connectors from the touch panel. The unit must be installed with
the attached connectors before being inserted into the drywall.

8. Insert the four sets of drywall screws and expansion clips into the four oval notch locations along
the top/bottom edges of the main unit (FIG. 39).
9. Carefully insert the main unit (with expansion clips) into the cutout until the Mounting Tabs on the
NXD unit lie flush against the wall (FIG. 39).
10. Tighten the drywall clip sets (screws and clips) until the Mounting Tabs are securely fastened and
flush against the wall.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

The drywall clip set must be re-ordered from AMX if the drywall clip is bent
accidentally during an installation or removed during a re-installation.

11. Place the magnetic faceplate (A in FIG. 39) back onto the main NXD unit (B in FIG. 39).
Make sure to align the Microphone, Light, and PIR Motion sensor locations to their respective
openings on the front bezel/faceplate.
12. Reconnect the terminal RJ-45, Ethernet, USB, and any optional audio/video wiring to their
respective locations on either the NXA-AVB/ETHERNET Breakout Box, Ethernet port, or NetLinx
Master.
13. Reconnect the terminal power connector on the 12 VDC-compliant power supply and apply power.
Installing the NXD into a Flat Surface using #4 screws
Mounting screws (#4, not included) are secured through circular holes located at the left and right sides
of the NXD panel. The most important thing to remember when mounting the NXD is that the
outer frame (Mounting Tabs) must be installed flush against the mounting surface.
It is recommended that you cutout the surface slightly smaller than what is outlined in the
installation drawings so that you can make any necessary cutout adjustments.

1. Prepare the area by removing any screws or nails from the surface before beginning the cutout
process.
2. Cut out the surface for the 12-inch Wall Mount using the dimensions shown in FIG. 40.

THESE 4 HOLES ARE ONLY REQUIRED
WHEN MOUNTING UNIT TO A SOLID
SURFACE (PODIUM, DESK, ETC.).
SECURE UNIT WITH #4 SCREWS.
CUTOUT

FRONT BEZEL

FIG. 40 NXD-1200V Wall Mount panel dimensions using #4 mounting screws

3. Remove the magnetic faceplate/bezel (A in FIG. 41) from the main NXD unit (B in FIG. 41) by
gripping the faceplate and pulling with gentle outward force.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

Attachment is done
along the edges of
the cutout
Install the four (#4)
mounting screws
into the holes
(screws not included)

A - Faceplate
(bezel)

Flat surface
(can include a
wall, podium, or
other flat
surface)

B - Main NXD unit consists of
the touch panel and housing

FIG. 41 Wall Mount panel installation configuration for flat/solid surfaces

4. Thread the incoming RJ-45, Ethernet, USB, and any other audio/video wiring (from their terminal
locations) through the cutout opening. Refer to the Wiring Guidelines for the 1200V Panels section
on page 45 for pinout descriptions.
Leave enough slack in the wiring to accommodate any re-positioning of the panel.
5. Connect all data and power wiring to their corresponding locations along the side of the
(un-powered) NXD touch panel.
Verify the terminal end of the power cable is not connected to power supply before plugging in
the 2-pin power connector.
The USB connectors can be from a either a USB extension cable, or a wireless USB RF
transmitter.

6. Test the incoming wiring by connecting the panel connections to their terminal locations and
applying power. Verify the panel is receiving power and functioning properly before finalizing the
installation.
7. Disconnect the terminal end of the power cable from the power supply.
Don’t disconnect the connectors from the touch panel. The unit must be installed with
the necessary connectors before being inserted into the solid surface.

8. Carefully slide the main unit into the cutout until the Mounting Tabs of the NXD unit lie flush
against the wall.
9. Insert and secure the four #4 screws into their corresponding holes located along the sides of the
NXD (using a grounded Phillips-head screwdriver) until the unit is secure and flush against the wall.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

10. Place the magnetic faceplate (A in FIG. 41) back onto the main NXD unit (B in FIG. 41).
Make sure to align the Microphone, Light, and PIR Motion sensor locations to their respective
openings on the front bezel/faceplate.
11. Reconnect the terminal RJ-45, Ethernet, USB, and any optional audio/video wiring to their
respective locations on either the NXA-AVB/ETHERNET Breakout Box, Ethernet port, or NetLinx
Master.
12. Reconnect the terminal power connector on the 12 VDC-compliant power supply and apply power.
Installing an NXD into an (optional) Rack Mount Kit (NXA-RK12)
1. Remove the magnetic faceplate/bezel from the main NXD unit by gripping the faceplate and pulling
with gentle outward force.
2. Thread the incoming RJ-45, Ethernet, USB, and any optional audio/video wiring through the
opening in the equipment rack (from their terminal locations). Refer to the Wiring Guidelines for
the 1200V Panels section on page 45 for pinout descriptions. Leave enough slack to accommodate
any re-positioning of the panel.
3. Connect all data and power wiring connectors to their corresponding locations along the side of the
(un-powered) NXD touch panel.
Verify the terminal end of the power cable is not connected to a power supply before plugging
in the 2-pin power connector.
The USB connectors can be from a either a USB extension cable, or a wireless USB RF
transmitter.

4. Test the incoming wiring by connecting the panel connections to their terminal locations and
applying power. Verify the panel is receiving power and functioning properly to prevent repetition
of the installation.
5. Disconnect the terminal end of the power cable from the connected power supply.
Don’t disconnect the connectors from the touch panel. The unit must be installed with
the necessary connectors before being inserted into the equipment rack.

6. Insert the main 12-inch Modero unit into an NXA-RK12 (FIG. 42).

Rack mount
frame (NXA-RK12)

Faceplate

FIG. 42 NXD-1200V 12 inch Wall Mount panel installed into an NXA-RK12 Rack Mount Kit

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

7. Secure the panel to the NXA-RK frame by first inserting and then tightening the four #4-40 screws
(provided). Line up the four mounting holes and use a grounded Phillips-head screwdriver to tighten
the screws in a clockwise direction.
8. Insert the NXA-RK (with connected NXD unit) into the equipment rack, making sure to align the
screw holes along the sides on the NXA-RK with the holes in the equipment rack.
9. Use a grounded Phillips-head screwdriver to secure the NXA-RK (with connected NXD unit) to the
equipment rack using #10-32 screws (not included).
10. Place the magnet faceplate back onto the main NXD unit by gripping the faceplate and placing it on
the housing with gentle force. Make sure to align the Microphone, Light, and PIR Motion sensor
locations to their respective openings on the front bezel/faceplate.
11. Reconnect the terminal RJ-45, Ethernet, and any optional audio/video wiring to their respective
locations on either the NXA-AVB/ETHERNET Breakout Box, Ethernet port, or NetLinx Master.
12. Reconnect the terminal power connector on the 12 VDC-compliant power supply and apply power.

Wiring Guidelines for the 1200V Panels
These panels require the use of a 12 VDC-compliant power supply to provide power to the panel via the
2-pin 3.5 mm mini-Phoenix PWR connector. Use the previously referenced power requirements
information to determine the power draw.
The incoming PWR and GND wires from the power supply must be connected to the corresponding
locations within the PWR connector.
These units should only have one source of incoming power. Using more than one
source of power to the touch panel can result in damage to the internal components
and a possible burn out.
Apply power to the panels only after installation is complete.

Preparing captive wires
You will need a wire stripper and flat-blade screwdriver to prepare and connect the captive wires.

Never pre-tin wires for compression-type connections.

1. Strip 0.25 inch (6.35 mm) of insulation off all wires.
2. Insert each wire into the appropriate opening on the connector (according to the wiring diagrams
and connector types described in this section).
3. Tighten the screws to secure the wire in the connector. Do not tighten the screws excessively; doing
so may strip the threads and damage the connector.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

Wiring a power connection
To use the 2-pin 3.5 mm mini-Phoenix connector with a 12 VDC-compliant power supply, the incoming
PWR and GND wires from the external source must be connected to their corresponding locations on the
connector (FIG. 43).

PWR +

Power Supply

GND To the Touch Panel
FIG. 43 NetLinx power connector wiring diagram

1. Insert the PWR and GND wires on the terminal end of the 2-pin 3.5 mm mini-Phoenix cable.
Match the wiring locations of the +/- on both the power supply and the terminal connector.
2. Tighten the clamp to secure the two wires. Do not tighten the screws excessively; doing so may strip
the threads and damage the connector.
3. Verify the connection of the 2-pin 3.5 mm mini-Phoenix to the power supply.

Audio/Video Port: Connections and Wiring
The following table shows the signal and pinout/pairing information used on the RJ-45 Audio and Video
connections.
Audio/Video RJ-45 Pinout Information
Pin

Wire Color

Function

Polarity

Orange/White

Right Audio In

Orange

Right Audio In

Green/White

Video In

Blue

Mic Out

White/Blue

Mic Out

Green

Video In

White/Brown

Left Audio In

Brown

Left Audio In

TIA 568B

1 2 3 4 5 6 7 8

(female)

(male)

RJ-45 connector - pin configurations

Refer to the Installing CAT5 Suppression Ferrites section on page 14 for detailed information on how to
install the necessary number of CAT5 Suppression Ferrites on the Black A/V RJ-45 cable connected to
the panel.

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

Ethernet/RJ-45 Port: Connections and Wiring
FIG. 44 describes the blink activity for the Ethernet 10/100 Base-T RJ-45 connector and cable. The
Ethernet cable is connected to the side of the Wall Mount panels
A - Activity LED (yellow)
lights when receiving or
transmitting Ethernet
data packets

L - Link LED (green) lights when
the Ethernet cables are connected
and terminated correctly.

ETHERNET
10/100

FIG. 44 Layout of Ethernet LEDs

The following table lists the pinouts, signals, and pairing associated with the Ethernet connector.
Ethernet RJ-45 Pinouts and Signals
Pin

Signals

Connections Pairing

Color

TX +

1 --------- 1

Orange-White

TX -

2 --------- 2

RX +

3 --------- 3

no connection 4 --------- 4

Blue

no connection 5 --------- 5

Blue-White

RX -

no connection 7 --------- 7

Brown-White

no connection 8 --------- 8

Brown

6 --------- 6

1 --------- 2

1 2 3 4 5 6 7 8

Orange
3 --------- 6

Green-White

Green

1 2 3 4 5 6 7 8

FIG. 45 diagrams the RJ-45 pinouts and signals for the Ethernet RJ-45 connector and cable.

FIG. 45 RJ-45 wiring diagram

1200V Modero Video Touch Panels

Installation Procedures: NXD-1200V Panels

1200V Modero Video Touch Panels

Panel Calibration

Panel Calibration
This section outlines the steps for calibrating the touch panel. It is recommended that you calibrate the
panel before its initial use and after completing a firmware download.
Modero panels are factory setup with specific demo touch panel pages. The first splash screen that
appears indicates the panel is receiving power, beginning to load firmware, and preparing to display the
default touch panel pages. When the panel is ready, the AMX Splash Screen is replaced by the Initial
Panel Page (FIG. 46).

AMX Splash Screen
(appears during power-up)

Initial Panel Page
(AMX Logo Page)

FIG. 46 AMX splash screen and initial Panel Page

Calibrating the Modero Panel
1. Press and hold the grey Front Setup Access button (FIG. 47) for 6 seconds (passing-over the Setup
page) to access the Calibration setup page (FIG. 48). The panel should first be calibrated properly.

Front Setup
Access button (grey)

- 3 second press/hold:
Accesses the Setup page
- 6 second press/hold:
Accesses the Calibration
page
Single press puts
the panel to sleep
FIG. 47 Location of grey Front Setup Access button

1200V Modero Video Touch Panels

Panel Calibration

2. Press the crosshairs (on the Calibration page) to set the calibration points on the LCD (FIG. 48).

The request to touch the crosshairs
is the first on-screen message
Calibration successful is the second
on-screen message that appears
after the calibration process is
completed
On-screen crosshairs used for
calibration of the touch device

FIG. 48 Touch Panel Calibration Screens

3. After the "Calibration Successful.." message appears, press anywhere on the screen to continue and
return to the Setup page.
If the calibration was improperly set and you cannot return to the Calibration
page (through the panel’s firmware); you can access this firmware page via
G4 WebControl where you can navigate to the Protected Setup page and press the
Calibrate button through your VNC window.
This action causes the panel to go to the Calibration page seen above, where you
can physically recalibrate the actual touch panel again using the above procedures.

Testing your Calibration
1. Press and hold down the on-screen Calibration button for 6 seconds to enter the Calibration Test
page (FIG. 49).

On-screen crosshairs is used to
verify a proper calibration of the
panel

FIG. 49 Calibration Test page

2. Press anywhere on this page to confirm the on-screen crosshairs match your touch points.
3. If the crosshairs do not appear directly below your LCD touch points, press the Back button and
recalibrate the panel using the above steps.
4. Exit this Calibration Test page by pressing the Back button to return to the Protected Setup page.

1200V Modero Video Touch Panels

Configuring Communication

Configuring Communication
Communication between the Modero panel and the Master is done using either USB or ETHERNET
(DHCP or Static IP). Ethernet communication can be achieved through either a direct connection
(Ethernet) or through the use of the optional NXA-PCI80211G wireless interface card.
USB input devices must be plugged into the rear or side USB connectors before the
G4 panel is powered-up. The panel will not detect a USB connection of this type until
after the unit cycles power.

Before commencing, verify you are using the latest NetLinx Master and Modero panel
firmware. Verify you are using the latest versions of AMX’s NetLinx Studio and
TPDesign4 programs.

Modero Setup and System Connection
1. Press the grey Front Setup Access button for 3 seconds to open the Setup page (FIG. 50).
Connection Status
Red Connection Status icon indicates no connection to a Master
Green Connection Status icon indicates communication to a Master
Yellow Connection Status icon indicates an unreliable network
connection
Battery Base button doesn’t appear
until NXT is connected to a BASE/B
FIG. 50 Setup page

2. Press the Protected Setup button (located on the lower-left of the panel page) to open the Protected
Setup page and display an on-screen keypad.
3. Enter 1988 into the Keypad’s password field and press Done when finished.
Clearing Password #5, from the initial Password Setup page, removes the need for
you to enter the default password before accessing the Protected Setup page.

4. Press the red Device Number field to open the Device Number keypad (FIG. 51).
5. Enter a Device Number value for the panel into the Device Number Keypad.
The default is 10001 and the range is from 1 - 32000.
When using multiple panels within a NetLinx System, remember to assign unique
Device Number values to each panel so that all assigned panels appear in the
System listing for the target Master.

6. Press Done to close the keypad, assign the number, and return to the Protected Setup page.

1200V Modero Video Touch Panels

Configuring Communication

FIG. 51 Protected Setup page

7. Press the on-screen Reboot button to restart the panel and incorporate any changes.
Before continuing, open NetLinx Studio 2.x. This program assists in developing a
System Number, Master IP/URL, and Master Port number. Refer to your NetLinx
Master’s instruction manuals for more information.

8. Obtain the System Number and Master IP Address from NetLinx Studio. This information must be
specific for the system used with the configured Modero panel.
9. Press the grey Front Setup Access button for 3 seconds to open the Setup page.
10. Press the Protected Setup button (located on the lower-left of the panel page) to open the Protected
Setup page.
11. Press the System Settings button (located on the Protected Setup page) to open the System Settings
page (FIG. 52) and begin configuring the communication settings on the panel to match those of the
target Master.

Modero
connection
information

NetLinx Master’s
connection
information

MAC Address
from panel is
factory set to a
unique address
FIG. 52 System Settings page

There are 2 possible Master Connection Types available: USB or Ethernet.
A USB connection type is a direct connection from the panel’s mini-USB port to a
corresponding USB port on the PC (acting as a Virtual Master).
An Ethernet connection type involves indirect communication from the panel to a
Master via an Ethernet connection to the network.

1200V Modero Video Touch Panels

Configuring Communication

It is recommended that firmware KIT files only be transferred over a direct connection
and only when the panel is connected to a power supply. If battery power or wireless
connection fails during a firmware upgrade, the panel flash file system may become
corrupted.
The mini-USB connector MUST be plugged into an already active panel before the
PC can recognize the connection and assign an appropriate USB driver. This driver is
part of the latest TPDesign4 software application installation.

Configuring and Using USB with a Virtual Master
NetLinx Studio can be setup to run a Virtual Master where the PC acts as the Master by supplying its
own IP Address for communication to the panel. The PC is first equipped with the USB driver, the panel
is then configured for USB communication, and then Studio is configured to act as the Master.
For a personal computer to establish a connection to a Modero panel via USB, the target computer must
have the appropriate AMX USB driver installed. This installation is bundled into the latest TPDesign4
software setup process or can be downloaded independently from the main Application Files page on
www.amx.com.

Step 1: Setting up the Panel and PC for USB Communication
1. If you do not currently have the latest version of TPDesign4, navigate to www.amx.com > Tech
Center > Downloadable Files > Application Files > NetLinx Design Tools section of the website
and locate the AMX USB Driver executable (AMX USBLAN Setup exe).
2. Download this executable file to a known location on your computer.
3. Launch the file by double-clicking on it and follow the on-screen prompts to complete your
installation. Note that even if you have loaded the latest AMX Studio or TPD4 software, you will
still need to download and install this file if you are working with either the 1200V-Series or
VG-Series of panels.
4. Choose the default language, agree to the Licensing information, and choose the location for the file
installations (C:\Program Files\AMX\USBLAN).
5. From within the Choose Components dialog, select the features you wish to install. The Driver
option is selected by default and is the only item required.
6. Click the Install button to continue with the installation.
7. Once the application begins the installation of the corresponding USB driver files, it may encounter
cases where previous versions of these files already exist. This can occur if you have previously
installed released versions of NetLinx Studio and TPDesign4.
If you are prompted to replace the AXBLAN.INF file, select YES.
If you are prompted to replace the Checked driver file, select NO.
If you are prompted to replace the AXBLAN.SYS and AXFILT.SYS files, select Yes.

8. Continue the setup process by following these OS-related processes:
For machines running Windows 2000 simply click the Next button when the installation is
complete. Creating a restore point is not an available option in 2000.
For Windows XP machines the setup program asks if you would like to create a restore point.
It is always a good idea to create restore points prior to installing new software.
Click the Next button when done.

9. At the end of the installation, press the Finish button.

1200V Modero Video Touch Panels

Configuring Communication

Step 2: Confirming the Installation of the USB Driver on the PC
The first time each AMX touch panel is connected to the PC it is detected as a new hardware device and
the USBLAN driver becomes associated with it (panel specific). Each time thereafter the panel is
"recognized" as a unique USBLAN device and the association to the driver is done in the background.
When the panel is detected for the first time some user intervention is required during the association
between panel and driver.

1. After the installation of the USB driver has been completed, confirm the proper installation of the
large Type-A USB connector to the PC's USB port, and restart your machine.
If the panel is already powered, continue with steps 3.
The panel MUST be powered and configured for USB communication before
connecting the mini-USB connector to the panel’s Program Port.

2. Connect the terminal end of the 12 VDC-compliant power supply cable to the power connector on
the rear/side of the touch panel and then apply power.
3. After the panel powers-up, press and hold the grey Front Setup Access button (for 3 seconds) to
continue with the setup process and proceed to the Setup page.
4. Select Protected Setup > System Settings (located on the lower-left) to open the System Settings
page (FIG. 53).
No connection is established until
the Virtual Master becomes
active within Studio
Yellow Connection Status icon indicates an unreliable network
connection
Red Connection Status icon indicates no connection to a Master
Green Connection Status icon indicates communication to a Master

FIG. 53 System Settings page - using a USB Connection Type

5. Toggle the blue Type field (from the Master Connection section) until the choice cycles to USB.
Refer to the System Settings Page section on page 118 for more information about the fields on this
page.
ALL fields are then greyed-out and read-only, but still display any previous network
information.

6. Press the Back button on the touch panel to return to the Protected Setup page.
7. Press the on-screen Reboot button to both save any changes and restart the panel. Remember that
the panel’s connection type must be set to USB prior to rebooting the panel and prior to inserting
the USB connector.

1200V Modero Video Touch Panels

Configuring Communication

8. ONLY AFTER the unit displays the first panel page, THEN insert the mini-USB connector into
the Program Port on the panel. It may take a minute for the panel to detect the new connection and
send a signal to the PC (indicated by a green System Connection icon). If this is your first time
installing the USB driver, a USB driver installation popup window (FIG. 54) then appears on the
screen.

FIG. 54 USB driver installation popup window

This window notifies you that the panel has been detected by the PC as a USB-compliant
device and the PC is installing an appropriate USB driver to establish a proper communication
to the panel.
The driver does not contain a Microsoft® digital signature and Windows® then informs you of
such.

9. Click Yes when told that a digital signature was not found. This action accepts the installation of the
new USB driver. The panel is now configured to communicate directly with the PC.
This process completes the association between driver and device.
Each time the same touch panel is connected to the computer the driver is automatically
loaded (using a unique name - example USB LAN LINK #1, #2).
Each time a different touch panel is connected to the computer, the previous procedures
will need to be repeated.
The previous version of the AMX USBLAN driver showed a USB connection icon in the
system tray when a panel was connected. The new version of the driver does not show an
icon in the System Tray.
A Virtual NetLinx Master (VNM) is used when the target panel is not connected to a
physical NetLinx Master. In this situation, the PC takes on the functions of a Master
via a Virtual NetLinx Master. This connection is made by either using the PC’s
Ethernet Address (via TCP/IP using a known PC’s IP Address as the Master) or
using a direct mini-USB connection to communicate directly to the panel.

10. Navigate back to the System Settings page.

1200V Modero Video Touch Panels

Configuring Communication

Step 3: Confirm and View the current AMX USB device connections
1. Navigate to Start > Settings > Control Panel > and double-click the System icon to launch the
System Properties dialog.
2. Select the Hardware tab and click on the Device Manager button to launch the Device Manager
dialog.
Within the Device Manager dialog, the AMX USBLAN device appears under Network
Adapters (FIG. 55) and has a unique name such as AMX USB LAN LINK #2. The number
changes depending on which recognized panel is currently connected.

USB connected touch
panel (showing the
recognized panel)

FIG. 55 Device Manager dialog showing USB device

To remove the USB driver association from a previously connected touch panel, you must navigate
back to the Device Manager, right-click on the panel’s USB driver (example AMX USB LAN LINK #2)
and select Uninstall from the context menu and then OK.
Once the system completes the removal of the device, the Device Manager window will
refresh, and the device will no longer appear.
The next time this device is connected to the computer it will appear as a new hardware device
and will need to be associated again with the driver (refer to Step 2: Confirming the
Installation of the USB Driver on the PC section on page 54.

Step 4: Using a USB to Configure a Virtual Master (using NetLinx Studio)
When configuring your panel to communicate via USB with a Virtual Master (on your
PC), ONLY the USB connection option must be selected within the Type field. Since
this is a direct connection, the PC’s IP Address is not needed.

Before beginning:

1. Verify the panel has been configured to communicate via USB within the System Settings page and
that the USB driver has been properly configured. Refer to the previous section for more
information.
2. Launch NetLinx Studio 2.x (default location is Start > Programs > AMX Control Disc > NetLinx
Studio 2 > NetLinx Studio 2).
3. Select Settings > Master Communication Settings, from the Main menu to open the Master
Communication Settings dialog (FIG. 56).
4. Click the Communications Settings button to open the Communications Settings dialog.

1200V Modero Video Touch Panels

Configuring Communication

IP Address of computer
(not needed as this is a direct
USB connection)
FIG. 56 Assigning Communication Settings for a Virtual Master

5. Click on the NetLinx Master radio button (from the Platform Selection section) to indicate that you
are working as a NetLinx Master.
6. Click on the Virtual Master radio box (from the Transport Connection Option section) to indicate
you are wanting to configure the PC to communicate directly with a panel. Everything else such as
the Authentication is greyed-out because you are not going through the Master’s UI.
7. Click the Edit Settings button (on the Communications Settings dialog) to open the Virtual NetLinx
Master Settings dialog (FIG. 56).
8. From within this dialog enter the System number (default is 1).
9. Click OK three times to close the open dialogs, save your settings, and return to the main NetLinx
Studio application.
10. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System.
The default System value is one.
11. Right-click on the Empty Device Tree/System entry and select Refresh System to re-populate the
list.
The panel will not appear as a device below the virtual system number (in the Online Tree tab)
until both the system number used in step 7 for the VNM is entered into the Master Connection
section of the System Settings page and the panel is restarted.
The Connection status turns green after a few seconds to indicate an active USB connection to
the PC (Virtual Master). No Lock icon is displayed because this USB connection is not
secured (requiring a username/password).
If a few minutes have gone by and the System Settings icon still does not turn green, repeat the
USB connection and Virtual Master setup procedures (outlined in this section). Refreshing the
System sends out a request to the panel to respond and completes the communication (turning
the System Connection icon green).

1200V Modero Video Touch Panels

Configuring Communication

Step 5: Confirm and View the current AMX USB device connections
Use the CC-USB Type-A to Mini-B 5-wire programming cable (FG10-5965) to provide communication
between the mini-USB Program port on the touch panel and the PC. This method of communication is
used to transfer firmware KIT files and TPD4 touch panel files.
A mini-USB connection is only detected after it is installed onto an active panel.
Connection to a previously powered panel which then reboots, allows the PC to
detect the panel and assign an appropriate USB driver.

1. Verify this direct USB connection (Type-A on the panel to mini-USB on the panel) is configured
properly using the steps outlined in the previous two sections.
2. With the panel already configured for USB communication and the Virtual Master setup within
NetLinx Studio, its now time to verify the panel is ready to receive files.
3. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System.
The default System value is one.
4. Right-click on the System entry (A in FIG. 57) and select Refresh System. This causes a refresh of
all project systems, establishes a new connection to the Virtual Master, and populates the System list
with devices on your particular system.

A
B

FIG. 57 Using USB for Virtual Master communication

1200V Modero Video Touch Panels

Configuring Communication

Wireless Settings Page - Wireless Access Overview
IP Routing
The behavior of the wireless routing is largely dependent on the wired network interface. Although the
panel can be connected to two networks simultaneously it may only have one gateway. If the wired
network was successfully set up and a gateway was obtained; then the default route for all network traffic
will be via the wired network. In the event that the wired network was not configured, then the default
route for all network traffic will be via the wireless network. The wired network connection always takes
priority.
As an example:
Imagine a panel connected to two networks A & B. A is the wired network and B is the
wireless network. If the Master controller is on either of these networks then it will be
reached. However if the Master controller is on a different network, C, then determining
which network interface (wired or wireless) that will be used is dependent on the gateway.

Hot Swapping
Hot swapping is not an issue on these panels as the card is installed within the unit and cannot be
removed without first removing the housing.
In the case of DHCP, there must be a DHCP server accessible before the fields are populated.

If the SSID (Network Name) and WEP fields have not previously been configured, the
Wireless Settings page will not work until the panel is rebooted.

Ethernet Communication from the panel can be direct (using an Ethernet cable) or indirect (through the
NXA-PCI80211G AMX Wireless Card (FG2255-04) communicating to a Wireless Access Point (WAP)
such as the NXA-WAP200G). In determining the Ethernet method of communication, the panel will
always default first to the direct Ethernet communication. If no direct connection is detected, the panel
will first check to see if there is an installed wireless interface card and then communicate to the WAP
using the Wireless Settings assigned within the Wireless Settings page. The WAP communication
parameters must match those of the pre-installed wireless interface card installed within the panel.
Wireless Access Points are the cornerstone of any wireless network. A Wireless Access Point
acts as a bridge between a wired and wireless network. It aggregates the traffic from all the
wireless clients and forwards it down the network to the switch or router. One Wireless
Access Point may be all you need. However, you could need more Wireless Access Points
depending on either how large your installation is, how it is laid out, and how it is constructed.
Wireless Equivalent Privacy (WEP) Security is a method by which WLANs protect wireless
data streams. A data stream encrypted with WEP can still be intercepted or eavesdropped
upon, but the encryption makes the data unintelligible to the interloper. The strength of WEP
is measured by the length of the key used to encrypt the data. The longer the key, the harder it
is to crack.
802.11b implementations provided 40-bit and 104-bit WEP keys. This is known respectively
as 64-bit and 128-bit WEP encryption. 64-bit is generally not regarded as adequate security
protection. Both key lengths are supported by the Modero product line. Whichever level of
WEP you use, it's crucial to use identical settings (CASE SENSITIVE)--the key length, and
the key itself-- on all devices. Only devices with common WEP settings will be able to
communicate. Similarly, if one device has WEP enabled and another doesn't, they won't be
able to talk to each other.

1200V Modero Video Touch Panels

Configuring Communication

Although the calculations required to encrypt data with WEP can impact the performance of
your wireless network, it's generally seen only when running benchmarks, and not large
enough to be noticeable in the course of normal network usage.

Configuring a Wireless Connection
When working with a wireless card, the first step is to configure wireless communication parameters
within the Wireless Settings page. This page only configures the card to communicate to a target WAP
(such as the NXA-WAP200G), it is still necessary to tell the panel which Master it should be
communicating with. This "pointing to a Master" is done via the System Settings page where you
configure the IP Address, System Number and Username/Password information assigned to the target
Master.

Step 1: Configuring the Panel’s Wireless IP Settings
The first step to successfully setting up your wireless card is to configure the IP Settings section of the
Wireless Settings page. The section configures the communication parameters from the Modero panel to
the web.

Wireless communication using a DHCP Address
1. Press the Protected Setup button (located on the lower-left of the panel page) to open the Protected
Setup page and display an on-screen keypad.
2. Enter 1988 into the Keypad’s password field and press Done when finished.
3. Press the Wireless Settings button (located on the lower-left) to open the Wireless Settings page.
Wireless communication is set within the IP Settings section of this page (FIG. 58).
4. Toggle the DHCP/Static field (from the IP Settings section) until the choice cycles to DHCP.
This action causes all fields in the IP Settings section (other than Host Name) to be greyed-out.
DHCP will register the unique MAC Address (factory assigned) on the panel and
once the communication setup process is complete, assign IP Address, Subnet
Mask, and Gateway values from the DHCP Server.

5. Press the optional Host Name field to open a Keyboard and enter the Host Name information.

Modero
connection
IP info.

FIG. 58 Wireless Settings page (IP Settings section)

6. Press Done after you are finished assigning the alpha-numeric string of the host name.
7. Do not alter any of these remaining greyed-out fields in the IP Settings section. Once the panel is
rebooted, these values are obtained by the unit and displayed in the DNS fields after power-up.

1200V Modero Video Touch Panels

Configuring Communication

This information can be found in either the Workspace - System name > Define
Device section of your code (that defines the properties for your panel), or in the
Device Addressing/Network Addresses section of the Tools > NetLinx Diagnostics
dialog.

8. Setup the security and communication parameters between the wireless card and the target WAP by
configuring the Wireless Settings section on this page. Refer to Step 2: Configuring the Card’s
Wireless Security Settings section on page 62 for detailed procedures to setup either a secure or
insecure connection.
Wireless communication using a Static IP Address
1. Press the Protected Setup button (located on the lower-left of the panel page) to open the Protected
Setup page and display an on-screen keypad.
2. Enter 1988 into the Keypad’s password field and press Done when finished.
3. Press the Wireless Settings button (located on the lower-left) to open the Wireless Settings page.
Wireless communication is set within the IP Settings section of this page (FIG. 58).
Check with your System Administrator for a pre-reserved Static IP Address assigned
to the panel. This address must be obtained before Static assignment of the panel
continues.

4. Toggle the DHCP/Static field (from the IP Settings section) until the choice cycles to Static.
The IP Address, Subnet Mask, and Gateway fields then become user-editable (red).
5. Press the IP Address field to open a Keyboard and enter the Static IP Address (provided by your
System Administrator).
6. Press Done after you are finished entering the IP information.
7. Repeat the same process for the Subnet Mask and Gateway fields.
8. Press the optional Host Name field to open the Keyboard and enter the Host Name information.
9. Press Done after you are finished assigning the alpha-numeric string of the host name.
10. Press the Primary DNS field to open a Keyboard, enter the Primary DNS Address (provided by your
System Administrator) and press Done when compete. Repeat this process for the Secondary DNS
field.
11. Press the Domain field to open a Keyboard, enter the resolvable domain Address (this is provided
by your System Administrator and equates to a unique Internet name for the panel), and press Done
when complete.
12. Setup the security and communication parameters between the wireless card and the target WAP by
configuring the Wireless Settings section on this page. Refer to the following section for detailed
procedures to setup either a secure or insecure connection.

1200V Modero Video Touch Panels

Configuring Communication

Step 2: Configuring the Card’s Wireless Security Settings
The second step to successfully setting up your wireless card is to configure the Wireless Settings section
of the Wireless Settings page. The section configures both the communication and security parameters
from the internal wireless card to the WAP. The procedures outlined within the following sections use
an NXA-WAP200G and the target WAP.
Once you have completed setting up the wireless card parameters, you must then
navigate to the System Settings page and configure the communication parameters
for the target Master. Until those parameters are configured, your Connection Status
icon will remain red (indicating that there is no current connection to a Master).

Configuring the Modero’s wireless card for unsecured access to a WAP200G
1. Power-down the Modero unit and follow the wireless card installation procedures outlined in Step 2:
Install the 802.11g mini-PCI Wireless Card section on page 19.
2. Power-up the panel (this allows it to detect the card).
3. Press the Protected Setup button (located on the lower-left of the panel page) to open the Protected
Setup page and display an on-screen keypad.
4. Enter 1988 into the Keypad’s password field and press Done when finished.
5. Press the Wireless Settings button (located on the lower-left) to open the Wireless Settings page.
6. From within the Wireless Settings section of the Wireless Settings page, touch the Network Name
(SSID) field (FIG. 59).

Mini-PCI
settings

FIG. 59 Wireless Settings page (showing default values)

7. From the Service Set Identifier keyboard, enter the SSID name used by your target Wireless Access
Point (case sensitive).
The card should be given the SSID used by the target WAP. If this field is left blank, the unit
will attempt to connect to the first available WAP. By default, all WAP200Gs use AMX as
their assigned SSID value.
One of the most common problems associated with connection to a WAP arise because the
SSID was not entered properly. You must maintain the same case when entering the SSID
information. ABC is not the same as Abc.

8. Toggle the Authentication field to an Open System (default).
Open System Authentication allows any device to join the network if the panel’s SSID
matches the WAP’s SSID.

9. Toggle the Encryption field until it reads Clear Text (default).

1200V Modero Video Touch Panels

Configuring Communication

The remaining Wireless Settings fields are then greyed-out and become read-only.
All NXA-WAP200Gs are factory-shipped as an unsecured WAP with no WEP
encryption. The WAP200G initial Status page will display the status of both the WEP
and WPA (both disabled).

10. Verify the fields in the IP Settings section have been properly configured. Refer to Step 1:
Configuring the Panel’s Wireless IP Settings section on page 60 for detailed information.
11. Press the Back button to navigate to the Protected Setup page and press the on-screen Reboot
button to both save any changes and restart the panel. Remember that you will need to navigate to
the System Settings page and configure the connection to a target Master.
12. After the panel restarts, return to the Wireless Settings page to verify the Link Quality and Signal
Strength:
The bargraphs have been replaced with descriptions: None, Poor, Fair, Good, Very Good,
and Excellent (FIG. 59).
The signal strength field should provide some descriptive text regarding the strength
of the connection to a Wireless Access Point. If there is no signal or no IP Address
displayed; configuration of your network could be required.

Refer to the NXA-WAP200G Instruction Manual for more detailed setup and configuration procedures.

Configuring the Modero’s wireless card for secured access to a WAP200G
After logging into the WAP200G, the default Status page appears within the web browser. These
read-only values are "pulled" from some of the other user-configurable Configuration Utility pages. By
default, wireless Modero panels are configured for unsecured communication to a Wireless Access
Point. To properly setup both the WAP200G and panel for secure communication, you must first prepare
the Modero panel and then use the information provided to fill out the fields within the WAP’s
browser-based Basic Wireless Configuration page.
Since the code key generator on Modero panels use the same key generation formula, all panels will
generate identical keys for the same Passphrase. The generators used on WAPs will not produce the same
key as the Modero generator even if you use the same Passphrase. This is why we recommend creating
the Current Key FIRST on the Modero and then entering that information into the appropriate
WAP200G fields.

1. Power-down the Modero unit and follow the wireless card installation procedures outlined in Step 2:
Install the 802.11g mini-PCI Wireless Card section on page 19.
When configuring touch panels for wireless communication, verify that no Ethernet
connector is installed within the panel before the unit is power cycled.

2. Power-up the panel (this allows it to detect the card).
3. Press the Protected Setup button (located on the lower-left of the panel page) to open the Protected
Setup page and display an on-screen keypad.
4. Enter 1988 into the Keypad’s password field and press Done when finished.
5. Press the Wireless Settings button (located on the lower-left) to open the Wireless Settings page.
6. Locate the Wireless Settings section of the Wireless Settings page (FIG. 60).

1200V Modero Video Touch Panels

Configuring Communication

SSID field
Mini-PCI wireless card communication
settings (for use with a target WAP)

Changes on this page take
effect after using the BACK
button to return to the
previous page

FIG. 60 Wireless Settings page (Wireless Settings section)

You must first take the SSID name, Current Key string value, and panel MAC
Address information and then later enter it into the appropriate WAP dialog fields in
order to "sync-up" the secure connection. These values must be identically
reproduced on the target WAP.

7. Touch the Network Name (SSID) field and from the Service Set Identifier keyboard, enter the SSID
name you will be using on your target Wireless Access Point (case sensitive).
The card should be given the SSID used by the target WAP. If this field is left blank, the unit
will attempt to connect to the first available WAP. By default, all WAP200Gs use AMX as
their assigned SSID value.
One of the most common problems associated with connection to a WAP arise because the
SSID was not entered properly. You must maintain the same case when entering the SSID
information. ABC is not the same as Abc.
The alpha-numeric string is by default AMX but can later be changed to any 32-character
entry. This string must be duplicated within the Network Name (SSID) field on the WAP.
As an example, if you use TECHPUBS as your SSID, you must match this word and the
case within both the Network Name (SSID) field on the touch panel’s Network Name SSID
field and on the WAP’s Basic Wireless Configuration page.

8. Leave the Authentication field reading Open System (default).
Open System Authentication allows any device to join the network if the panel’s SSID
matches the WAP’s SSID. An Open System is recommended for communication between
Modero panels and an NXA-WAP200G.
Shared Key Authentication requires that the panel and the Wireless Access Point have the
same WEP Key to authenticate.

9. Toggle the Encryption field (FIG. 60) until it reads WEP64 or WEP128. The 64/128 selection
reflects the bit-level of encryption security. This WEP encryption level must match the encryption
level being used on the WAP.
WEP will not work unless the same Default Key is set on both the panel and the
Wireless Access Point.
For example: if you have your Wireless Access Point set to default key 4 (which
was 01:02:03:04:05), you must set the panel’s key 4 to 01:02:03:04:05.

1200V Modero Video Touch Panels

Configuring Communication

10. Toggle the Default Key field until the you’ve chosen a WEP Key value (from 1- 4) that matches
what you’ll be using on your target WAP200G.
These WEP Key identifier values must match for both devices.

11. With the proper WEP Key value displayed, press the Generate button to launch the WEP
Passphrase keyboard.
If you are wanting to have your target WAP (other than a 200G) generate the Current Key - Do
not press the Generate button and continue with Step 14.
This keyboard allows you to enter a Passphrase (such as AMXPanel) and then
AUTOMATICALLY generate a WEP key which is compatible only among Modero panels.
The code key generator on Modero panels use the same key generation formula.
Therefore, this same Passphrase generates identical keys when done on any
Modero because they all use the same Modero-specific generator. The Passphrase
generator is case sensitive.

12. Within this on-screen WEP Passphrase keyboard (FIG. 61), enter a character string or word (such as
AMXPanel) and press Done when you have finished.

FIG. 61 WEP Passphrase Keyboard

As an example, enter the word AMXPanel using a 128-bit hex digit encryption. After
pressing Done, the on-screen Current Key field displays a long string of characters (separated
by colons) which represents the encryption key equivalent to the word AMXPanel.
This series of hex digits (26 hex digits for a 128-bit encryption key) should be entered as
the Current Key into both the WAP and onto other communicating Modero panels by
using the WEP Key dialog (FIG. 62).

FIG. 62 WEP Key # Keyboard

1200V Modero Video Touch Panels

Configuring Communication

13. Write down this Current Key string value for later entry into your WAP’s WEP Key field (typically
entered without colons) and into the communicating panel’s Current Key field (FIG. 60).
14. If you are entering a Current Key generated either by your target WAP or another Modero
panel, within the WEP Keys section, touch the Key # button to launch the WEP Key # keyboard
(FIG. 62), enter the characters and press Done when finished.
This Key value corresponds to the Default WEP Key number used on the Wireless Access
Point and selected in the Default Key field described in the previous step.
If your target Wireless Access Point does not support passphrase key generation and
has previously been setup with a manually entered WEP KEY, you must manually
enter that same WEP key on your panel.

15. Verify the fields within the IP Settings section have been properly configured. Refer to Step 1:
Configuring the Panel’s Wireless IP Settings section on page 60 for detailed information.
16. Press the Back button to navigate to the Protected Setup page and press the on-screen Reboot
button to both save any changes and restart the panel. Remember that you will need to navigate to
the System Settings page and configure the connection to a target Master.
17. After the panel restarts, return to the Wireless Settings page to verify the Link Quality and Signal
Strength:
The bargraphs have been replaced with descriptions: None, Poor, Fair, Good, Very Good,
and Excellent.
The signal strength field provides some descriptive text regarding the strength of the
connection to a Wireless Access Point. If there is no signal or no IP Address
displayed; configuration of your network could be required.

Refer to the NXA-WAP200G Instruction Manual for more detailed setup and configuration procedures.

Configuring multiple wireless Moderos to communicate to a target WAP200G
1. For each communicating touch panel, complete all of the steps outlined within the previous
Configuring the Modero’s wireless card for secured access to a WAP200G section on page 63.
Those procedures walk you through assigning an SSID, selecting a WEP encryption level, and
obtaining a Current Key string value for a specific WEP Key on a target panel.

2. Navigate back to the Wireless/Wireless Settings page on each panel.
3. Verify that all communicating Modero panels are using the same SSID, encryption level, Default
Key #, and an identical Current Key value.
As an example, all panels should be set to Default Key #1 and be using aa:bb:cc..as the
Current Key string value. This same Key value and Current Key string should be used on the
target WAP.

4. Repeat steps 1 - 3 on each panel. Using the same passphrase, generates the same key for all
communicating Modero panels.

1200V Modero Video Touch Panels

Configuring Communication

Configuring a Wired Ethernet Connection
It is necessary to tell the panel which Master it should be communicating with. This "pointing to a
Master" is done via the System Settings page where you configure the IP Address, System Number and
Username/Password information assigned to the target Master. If you have previously established a
wireless connection to the Internet you must still navigate to the System Settings page and configure the
communication parameters for the target Master. Until those parameters are configured, your Connection
Status icon will remain red (indicating there is no current connection to a Master).
If you have previously configured an internal wireless card for communication to the Internet,
you do not need to configure the panel’s IP Settings fields and can skip the following Step 1.

Step 1: Configuring the Panel’s Wired IP Settings
There are only two available methods of communicating to a target Master over the Internet: Wireless
(via an internal card) or Wired (direct Ethernet connection). If you are not using an internal wireless
card, you can only configure the connection parameters through the System Settings page. This type of
communication can be established either via either a Dynamic IP Address (DHCP) or via a
pre-reserved Static IP Address (typically provided by your System Administrator).

IP Settings section - Configuring a DHCP Address over Ethernet
1. Select Protected Setup > System Settings (located on the lower-left) to open the System Settings
page.
2. Locate the IP Settings section of this page.
Even though the Host, Gateway, Primary DNS, Secondary DNS, and Domain fields
appear on the two separate System Settings and Wireless Settings pages; the
information populating these fields is identical.
If the information within one of these fields is altered, the change is reflected on both
pages within the altered field.
Example: Domain is altered on Wireless Settings page, the value is then also
changed within the Domain field of the System Settings page.

3. Toggle the DHCP/Static field (from the IP Settings section) until the choice cycles to DHCP.
DHCP will register the unique MAC Address (factory assigned) on the panel and
once the communication setup process is complete, reserve an IP Address, Subnet
Mask, and Gateway values from the DHCP Server.

4. Press the optional Host Name field to open a Keyboard and enter the Host Name information.
5. Press Done after you are finished assigning the alpha-numeric string of the host name.
6. Do not alter any of the remaining greyed-out fields in the IP Settings section. Once the panel is
rebooted, these values are obtained by the unit and displayed in the DNS fields after power-up.
This information can be found in either the: Workspace- System name > Define
Device section of your code (that defines the properties for your panel), or in the
Device Addressing/Network Addresses in the Tools > NetLinx Diagnostics dialog.

7. Press the Back button to return to the Protected Setup page.
8. Press the on-screen Reboot button to both save any changes and restart the panel.

1200V Modero Video Touch Panels

Configuring Communication

IP Settings section - Configuring a Static IP Address over Ethernet
1. Select Protected Setup > System Settings (located on the lower-left) to open the System Settings
page.
2. Locate the IP Settings section of this page.
Check with your System Administrator for a pre-reserved Static IP Address assigned
to the panel. This address must be obtained before Static assignment of the panel
continues.

3. Toggle the DHCP/Static field (from the IP Settings section) until the choice cycles to Static.
4. Press the IP Address field to open a Keyboard and enter the Static IP Address (provided by your
System Administrator).
5. Press Done after you are finished entering the IP information.
6. Repeat the same process for the Subnet Mask and Gateway fields.
7. Press the optional Host Name field to open the Keyboard and enter the Host Name information.
8. Press Done after you are finished assigning the alpha-numeric string of the host name.
9. Press the Primary DNS field to open a Keyboard, enter the Primary DNS Address (provided by your
System Administrator) and press Done when compete. Repeat this process for the Secondary DNS
field.
10. Press the Domain field to open a Keyboard, enter the resolvable domain Address (this is provided by
your System Administrator and equates to a unique Internet name for the panel), and press Done
when complete.
11. Navigate to the Master Connection section of this page to begin configuring the communication
parameters for the target Master.

Step 2: Choosing a Master Connection Mode Setting
There are three Ethernet MODE settings used in the Master Connection section of the System Settings
page. URL is the most common method.
Master Connection MODE options:
• URL (Uniform Resource Locator) is the address that defines the route to a file on the Web or
any other Internet facility.
In this system, the panel acts as a "Client" and the Master acts as a Server (in that Clients attach
to it).
• LISTEN sets the Modero panel to "listen" for broadcasts from the Master (using the panel IP from
its URL list). In this system, the panel acts as a "Server" (in that Clients attach to it) and the Master
acts as a "Client".
• AUTO is used to instruct the Modero to search for a Master that uses the same System Number
(assigned within the Master Connection section) and resides on the same Subnet as itself. In this
case, the Master has its UDP feature enabled.
This UDP (User Datagram Protocol) is a protocol within the TCP/IP protocol suite that is used in
place of TCP when a reliable delivery is not required.
This UDP enabling is done through a Telnet session on the Master. Refer to the particular NetLinx
Master manual for more detailed information.

1200V Modero Video Touch Panels

Configuring Communication

Step 3: Configuring the Ethernet Connection Type
When using Ethernet as your communication method, the NetLinx Master must first
be setup with either a Static IP or DHCP Address obtained from either NetLinx Studio
or your System Administrator.

Before beginning:

1. Verify the panel has been configured to communicate either through an Ethernet cable (connected
from either the panel to a valid Ethernet Hub) or to a wirelessly to the Wireless Access Point
(WAP).

Before commencing, verify you are using the latest NetLinx Master firmware.

2. Verify that the NetLinx Master is receiving power and is communicating via an Ethernet connection
with the PC running NetLinx Studio.
3. Connect the terminal end of the 12 VDC-compliant power supply cable to the power connector on
the rear/side of the touch panel.
4. Verify the green Ethernet LED (from the rear Ethernet port on the Master) is illuminated (indicating
a proper connection).
5. Verify the yellow LED (from the rear Ethernet port on the Master) is blinking (indicating
communication).
6. After the panel powers-up, press and hold the grey Front Setup Access button (for 3 seconds) to
proceed to the Setup page.
7. Select Protected Setup > System Settings (located on the lower-left) to open the System Settings
page (FIG. 63).

Obtained
from
NetLinx
Master

FIG. 63 System Settings page

1200V Modero Video Touch Panels

Configuring Communication

Master Connection - Virtual Master communication over Ethernet
When configuring your panel to communicate with a Virtual Master (on your PC) via
Ethernet, the Master IP/URL field must be configured to match the IP Address of the
PC and make sure to use the Virtual System value assigned to the Virtual Master
within NetLinx Studio.

Before beginning:

1. Verify the panel has been configured to communicate either through an Ethernet cable (connected
from either the panel to a valid Ethernet Hub) or wireless to the Wireless Access Point.
2. Launch NetLinx Studio 2.x (default location is Start > Programs > AMX Control Disc > NetLinx
Studio 2 > NetLinx Studio 2).
3. Select Settings > Master Communication Settings, from the Main menu to open the Master
Communication Settings dialog (FIG. 64).

Enter this IP
into the
Master IP/URL
field on the
System Settings
page

IP Addresses of computer
(also obtained by using the
Start > Run > cmd command)

FIG. 64 Assigning Communication Settings and TCP/IP Settings for a Virtual Master

4. Click the Communications Settings button to open the Communications Settings dialog.
5. Click on the NetLinx Master radio button (from the Platform Selection section) to indicate that you
are working as a NetLinx Master.
6. Click on the Virtual Master radio box (from the Transport Connection Option section) to indicate
you are wanting to configure the PC to communicate with a panel. Everything else such as the
Authentication is greyed-out because you are not going through the Master’s UI.
7. Click the Edit Settings button (on the Communications Settings dialog) to open the Virtual NetLinx
Master Settings dialog (FIG. 64).
8. From within this dialog enter the System number (default is 1) and note the IP Address of the target
PC being used as the Virtual Master. This IP Address can also be obtained by following these
procedures:
On your PC, click Start > Run to open the Run dialog.
Enter cmd into the Open field and click OK to open the command DOS prompt.
From the C:\> command line, enter ipconfig to display the IP Address of the PC. This
information is entered into the Master IP/URL field on the panel.

9. Click OK three times to close the open dialogs, save your settings, and return to the main NetLinx
Studio application.

1200V Modero Video Touch Panels

Configuring Communication

10. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System.
The default System value is one.
11. Right-click on the Empty Device Tree/System entry and select Refresh System to re-populate the
list.
12. Power-up your panel and press and hold the grey Front Setup Access button (for 3 seconds) to
continue with the setup process and proceed to the Setup page.
13. Select Protected Setup > System Settings (located on the lower-left) to open the System Settings
page (FIG. 65).
The System Number is
assigned to the Master
within the AMX
software application
(these must match)
Enter the IP Address
information of the PC
used as a Virtual
Master

When using a Virtual Master,
there is no need to enter a
username and/or password
FIG. 65 Sample System Settings page (for Virtual Master communication)

14. Press the blue Type field (from the Master Connection section) until the choice cycles to the word
Ethernet. ICSNet communication cannot be used on either 1200V-Series or VG-Series panels.
15. Press the Mode field until the choice cycles to the word URL.
By selecting URL, the System Number field becomes read-only (grey) because the panel pulls
this value directly from the communicating target Master (virtual or not). A Virtual Master
system value can be set within the active AMX software applications such as: NetLinx Studio,
TPD4, or IREdit.

16. Press the Master IP/URL field to open a Keyboard and enter the IP Address of the PC used as the
Virtual Master.
17. Click Done to accept the new value and return to the System Settings page.
18. Do not alter the Master Port Number value (this is the default value used by NetLinx).
19. Press the Back button to open the Protected Setup page.
20. Press the on-screen Reboot button to both save any changes and restart the panel.

1200V Modero Video Touch Panels

Configuring Communication

Master Connection section - NetLinx Master Ethernet IP Address - URL Mode
In this mode, enter the System Number (zero for an unknown System Number) and the IP/URL of the
Master (Master Port Number is defaulted to 1319).

1. Press the blue Type field (from the Master Connection section) until the choice cycles to the word
Ethernet. Refer to the System Settings Page section on page 118 for more information about the
fields on this page.
2. Press the Mode field until the choice cycles to the word URL.
By selecting URL, the System Number field becomes read-only (grey) because the panel pulls
this value directly from the communicating target Master (virtual or not). A Virtual Master
system value can be set within the active AMX software applications such as: NetLinx Studio,
TPD4, or IREdit.
If the panel does not appear within the OnLine Tree tab of the Workspace window of
NetLinx Studio, check to make sure that the NetLinx Master System Number (from
within the Device Addressing dialog) is correctly assigned.

3. Press the Master IP/URL field to open a Keyboard and enter the Master IP Address (obtained from
the Diagnostics - Networking Address dialog of the NetLinx Studio application).
4. Click Done to accept the new value and return to the System Settings page.
5. Do not alter the Master Port Number value (this is the default value used by NetLinx).
6. Enter a username and password (into their respective fields) if the target Master has been previously
secured.
7. Press the Back button to open the Protected Setup page.
8. Press the on-screen Reboot button to both save any changes and restart the panel.
Master Connection section - NetLinx Master Ethernet IP Address - Listen Mode
In this mode, you must add the Modero panel IP Address into the URL List of the Master (using NetLinx
Studio). This mode sets the Modero panel to "listen" for broadcasts from the Master (using the panel IP
from its URL list).

1. Obtain either a Static IP for the Modero panel (from your System Administrator) or a DHCP
Address from the IP Settings of the System Settings page.
The DHCP/Static field (in the IP Settings section of the System Settings page) must be set to
DHCP to get Dynamic IP information for the panel.
Press the on-screen Reboot (from the Protected Setup page) to both save any changes and
restart the panel.
After power-up, press the grey Front Setup Access button for 3 seconds to access the Setup
page.
Navigate to the Setup > Protected Setup > System Settings page and note the newly
obtained Dynamic IP Address information from the IP Settings section. This information is
then entered into the URL List for the connected NetLinx Master.

2. Toggle the blue Type field until Ethernet is selected (from the Master Connection section of the
System Settings page).
3. Press the Mode field (to set the connection Mode) until the choice cycles to the word Listen.
4. Enter a username and password (into their respective fields) if the target Master has been previously
secured.
5. Select the OnLine Tree tab from the Workspace window.

1200V Modero Video Touch Panels

Configuring Communication

6. Select Diagnostics > URL Listing from the Main menu (FIG. 66).
System Address
reflects the value
set in the Device
Addressing tab

Used to obtain an
existing URL
List from Master

Used to set the
URL List
on Master
FIG. 66 URL List dialog

7. Enter the System and Device number for the specific Master associated with your panel (as seen in
the Online Tree tab).
8. Click Add and enter the IP Address of the Modero touch panel into the Add URL dialog box.
9. Click OK to enter your IP Address and add it to the list.
10. Click Done once you are finished adding your panel information to the list.
11. Press the on-screen Reboot button to save any changes and restart the panel.
Master Connection section - NetLinx Master Ethernet IP Address - Auto Mode
In this mode, enter the System Number of the NetLinx Master. This mode instructs the Modero to search
for a Master that uses the same System Number (assigned within the Master Connection section) and
resides on the same Subnet as itself.

1. Toggle the blue Type field until Ethernet is selected (from the Master Connection section of the
System Settings page).
2. Press the Mode field until the choice cycles to the word Auto.
3. Press the System Number field to launch a Keypad and enter the value for the system number of the
NetLinx Master. This value can be obtained from the NetLinx Studio program > OnLine Tree of the
Workspace window.
4. Do not alter the IP Settings section, of the System Settings page, as these fields are not applicable to
this connection mode.
5. Enter a username and password (into their respective fields) if the target Master has been previously
secured.
6. Press the on-screen Reboot button to both save any changes and restart the panel.
7. Press the grey Front Setup Access button for 3 seconds to open the Setup page and confirm there is
an active connection.

The NetLinx Master and the Modero panel must both be on the same Subnet.

1200V Modero Video Touch Panels

Configuring Communication

Using G4 Web Control to Interact with a G4 Panel
The G4 Web Control feature allows you to use a PC to interact with a G4 enabled panel via the web. This
feature works in tandem with the new browser-capable NetLinx Security firmware update
(build 300 or higher). G4 Web Control is only available with the latest Modero panel firmware.
Refer to the G4 Web Control Page section on page 108 for more detailed field information.
Verify your NetLinx Master (ME260/64 or NI-Series) has been installed with the latest
firmware KIT file from www.amx.com. Refer to your NetLinx Master Instruction
Manual for more detailed information on the use of the new web-based NetLinx
Security.

1. Press the grey Front Setup Access button for 3 seconds to open the Setup page.
2. Press the Protected Setup button (located on the lower-left of the panel page) to open the Protected
Setup page and display an on-screen keypad.
3. Enter 1988 into the Keypad’s password field (1988 is the default password).
Clearing Password #5, from the initial Password Setup page, removes the need for
you to enter the default password before accessing the Protected Setup page.

4. Press Done when finished.
5. Press the G4 Web Control button to open the G4 Web Control page (FIG. 67).

FIG. 67 G4 Web Control page

6. Press the Enable/Enabled button until it toggles to Enabled (light blue color).
7. The Network Interface Select field is read-only and displays the method of communication to the
web. Verify you have selected the proper interface connection as this field does not auto-detect
the connection type being used (see below).
Wired is used when a direct Ethernet connection is being used for communication to the web.
This is the default setting if either no wireless interface card is detected or if both an Ethernet
and wireless card connection is detected by the panel.
Wireless is used when a wireless card is detected within the internal card slot. This method
provides an indirect communication to the web via a pre-configured Wireless Access Point.

8. Press the Web Control Name field to open the Web Name keyboard.

1200V Modero Video Touch Panels

Configuring Communication

9. From the Web Name keyboard, enter a unique alpha-numeric string to identify this panel. This
information is used by the NetLinx Security Web Server to display on-screen links to the panel. The
on-screen links use the IP Address of the panel and not the name for communication (FIG. 68).

FIG. 68 Sample relationship between G4 Web Control and Mange WebControl Connections window

10. Press Done after you are finished assigning the alpha-numeric string for the Web Control name.
11. Press the Web Control Password field to open the Web Password keyboard.
12. From the Web Password keyboard, enter a unique alpha-numeric string to be assigned as the G4
Authentication session password associated with VNC web access of this panel.
13. Press Done after you are finished assigning the alpha-numeric string for the Web Control password.
14. Press the Web Control Port field to open the Web Port Number keypad.
15. Within the keypad, enter a unique numeric value to be assigned to the port the VNC Web Server is
running on. The default value is 5900.
16. Press Done when you are finished entering the value. The remaining fields within the G4 Web
Control Settings section of this page are read-only and cannot be altered.
17. Press the Up/Down arrows on either sides of the G4 Web Control Timeout field to increase or
decrease the amount of time the panel can remain idle (no cursor movements) before the session is
closed and the user is disconnected.
18. Press the Back button to open the Protected Setup page.
19. Press the on-screen Reboot button to save any changes and restart the panel.
Verify your NetLinx Master’s IP Address and System Number have been properly
entered into the Master Connection section of the System Settings page.

1200V Modero Video Touch Panels

Configuring Communication

Using your NetLinx Master to control the G4 panel
Refer to your particular NetLinx Master’s instruction manual for detailed information on how to
download the latest firmware from www.amx.com. This firmware build enables SSL certificate
identification and encryption, HTTPS communication, ICSP data encryption, and disables the ability to
alter the Master security properties via a TELNET session.

In order to fully utilize the SSL encryption, your web browser should incorporate the an encryption
feature. This encryption level is displayed as a Cipher strength.

Once the Master’s IP Address has been set through NetLinx Studio version 2.x or higher:

1. Launch your web browser.
2. Enter the IP Address of the target Master (ex: http://198.198.99.99) into the web browser’s Address
field.
3. Press the Enter key on your keyboard to begin the communication process between the target
Master and your computer.
Initially, the Master Security option is disabled (from within the System Security page) and
no username and password is required for access or configuration.
Both HTTP and HTTPS Ports are enabled by default (via the Manage System > Server
page).
If the Master has been previously configured for secured communication, click OK to accept
the AMX SSL certificate (if SSL is enabled) and then enter a valid username and password
into the fields within the Login dialog.

4. Click OK to enter the information and proceed to the Master’s Manage WebControls window.
5. This Manage WebControl Connections page (FIG. 69) is accessed by clicking on the Manage
connections link (within the Web Control section within the Navigation frame). Once activated, this
page displays links to G4 panels running the latest G4 Web Control feature (previously setup and
activated on the panel).

Compatible
devices field
(showing G4
WebControl links)

G4 panels

Compression
Options

FIG. 69 Manage WebControl Connections page (populated with compatible panels)

6. Click on the G4 panel name link associated with the target panel. A secondary web browser window
appears on the screen (FIG. 70).

1200V Modero Video Touch Panels

Configuring Communication

FIG. 70 Web Control VNC installation and Password entry screens

7. Click Yes from the Security Alert popup window to agree to the installation of the G4 WebControl
application on your computer. This application contains the necessary Active X and VNC client
applications necessary to properly view and control the panel pages from your computer.
The G4 Web Control application is sent by the panel to the computer that is used for
communication. Once the application is installed, this popup will no longer appear.
This popup will only appear if you are connecting to the target panel using a different
computer.

8. In some cases, you might get a Connection Details dialog (FIG. 71) requesting a VNC Server IP
Address. This is the IP Address not the IP of the Master but of the target touch panel. Depending on
which method of communication you are using, it can be found in either the:
Wired Ethernet - System Settings > IP Settings section within the IP Address field.
Wireless - Wireless Settings > IP Settings section within the IP Address field.
If you do not get this field continue to step 9.

IP Address of touch panel
- obtained from IP Settings section of
the System Settings page

FIG. 71 Connection Details dialog

9. If a WebControl password was setup on the G4 WebControl page, a G4 Authentication Session
password dialog box appears on the screen within the secondary browser window.
10. Enter the Web Control session password into the Session Password field (FIG. 70). This password
was previously entered into the Web Control Password field within the G4 Web Control page on the
panel.

1200V Modero Video Touch Panels

Configuring Communication

11. Click OK to send the password to the panel and begin the session. A confirmation message appears
stating "Please wait, Initial screen loading.".
The secondary window then becomes populated with the same G4 page being displayed on the target G4
panel. A small circle appears within the on-screen G4 panel page and corresponds to the location of the
mouse cursor. A left-mouse click on the computer-displayed panel page equates to an actual touch on the
target G4 panel page.

1200V Modero Video Touch Panels

Upgrading Modero Firmware

Upgrading Modero Firmware
Before beginning the Upgrade process:
Setup and configure your NetLinx Master. Refer to your particular NetLinx Master instruction
manual for detailed setup procedures.
Calibrate and prepare the communication pages on the Modero panel for use. Refer to the
Panel Calibration section on page 49.
Refer to the NetLinx Studio version 2.x or higher Help file for more information on uploading
files via Ethernet.
Configure your panel for either direct connect or wireless communication. Refer to the
Configuring Communication section on page 51 for more detailed information about Ethernet
or Wireless communication.
It is recommended that firmware Kit files only be transferred over a direct Ethernet
connection and only when the panel is connected to a power supply.
If battery power or wireless connection fails during a firmware upgrade, the panel
flash file system may become corrupted.

The process of updating firmware involves the use of a communicating NetLinx Master. The required
steps for updating firmware to a Modero panel are virtually identical to those necessary for updating Kit
files to a NetLinx Master (except the target device is a panel instead of a Master). Refer to either your
Master’s literature or Studio 2.x Help file for those procedures.
A touch panel which is not using a valid username and password will not be able to
communicate with a secured Master. If you are updating the firmware on or through a
panel which is not using a username or password field, you must first remove the
Master Security feature to establish an unsecured connection.

Upgrading the Modero Firmware via the USB port
Before beginning with this section, verify your panel is powered and the Type-A USB connector is
securely inserted into the PC’s USB port. The panel must be powered-on before connecting the miniUSB connector to the panel.

Establishing a USB connection between the PC and the panel, prior to installing the
USB Driver will cause a failure in the USB driver installation.

Step 1: Configure the panel for a USB Connection Type
1. After the installation of the USB driver has been completed, confirm the proper installation of the
large Type-A USB connector to the PC's USB port, and restart your machine.
2. After the panel powers-up, press and hold the grey Front Setup Access button (for 3 seconds) to
continue with the setup process and proceed to the Setup page.
3. Select Protected Setup > System Settings (located on the lower-left) to open the System Settings
page.
4. Toggle the blue Type field (from the Master Connection section) until the choice cycles to USB.

1200V Modero Video Touch Panels

Upgrading Modero Firmware

ALL fields are then greyed-out and read-only, but still display any previous network
information.

5. Press the Back button on the touch panel to return to the Protected Setup page.
6. Press the on-screen Reboot button to both save any changes and restart the panel. Remember that
the panel’s connection type must be set to USB prior to rebooting the panel and prior to inserting
the USB connector.
7. ONLY AFTER the unit displays the first panel page, THEN insert the mini-USB connector into
the Program Port on the panel. It may take a minute for the panel to detect the new connection and
send a signal to the PC (indicated by a green System Connection icon).
If a few minutes have gone by and the System Connection icon still does not turn green,
complete the procedures in the following section to setup the Virtual Master and refresh the
System from the Online Tree. This action sends out a request to the panel to respond and
completes the communication (turning the System Connection icon green).

8. Navigate back to the System Settings page.
Step 2: Prepare NetLinx Studio for communication via the USB port
1. Launch NetLinx Studio 2.x (default location is Start > Programs > AMX Control Disc > NetLinx
Studio 2 > NetLinx Studio 2).
2. Select Settings > Master Communication Settings, from the Main menu to open the Master
Communication Settings dialog (FIG. 72).

IP Address of computer
(not needed as this is a direct
USB connection)
FIG. 72 Assigning Communication Settings for a Virtual Master

3. Click the Communications Settings button to open the Communications Settings dialog.
4. Click on the NetLinx Master radio button (from the Platform Selection section) to indicate that you
are working as a NetLinx Master.
5. Click on the Virtual Master radio box (from the Transport Connection Option section) to indicate
you are wanting to configure the PC to communicate directly with a panel. Everything else such as
the Authentication is greyed-out because you are not going through the Master’s UI.
6. Click the Edit Settings button (on the Communications Settings dialog) to open the Virtual NetLinx
Master Settings dialog (FIG. 72).

1200V Modero Video Touch Panels

Upgrading Modero Firmware

7. From within this dialog enter the System number (default is 1).
8. Click OK three times to close the open dialogs, save your settings, and return to the main NetLinx
Studio application.
9. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System. The
default System value is one.
10. Right-click on the Empty Device Tree/System entry and select Refresh System to re-populate the
list.
The panel will not appear as a device below the virtual system number (in the Online Tree tab)
until both the system number used in step 7 for the VNM is entered into the Master Connection
section of the System Settings page and the panel is restarted.
Step 3: Confirm and Upgrade the firmware via the USB port
Use the CC-USB Type-A to Mini-B 5-wire programming cable (FG10-5965) to provide communication
between the mini-USB Program port on the touch panel and the PC. This method of communication is
used to transfer firmware Kit files and TPD4 touch panel files.
A mini-USB connection is only detected after it is installed onto an active panel.
Connection to a previously powered panel which then reboots, allows the PC to
detect the panel and assign an appropriate USB driver.

1. Verify this direct USB connection (Type-A on the panel to mini-USB on the panel) is configured
properly using the steps outlined in the previous two sections.
2. With the panel already configured for USB communication and the Virtual Master setup within
NetLinx Studio, its now time to verify the panel is ready to receive files.
3. After the Communication Verification dialog window verifies active communication between the
Virtual Master and the panel, click the OnLine Tree tab in the Workspace window (FIG. 73) to
view the devices on the Virtual System. The default System value is one.
4. Right-click on the System entry (FIG. 73) and select Refresh System to re-populate the list. Verify
the panel appears in the OnLine Tree tab of the Workspace window.
The default Modero panel value is 10001.
Showing a Master
firmware version and
device number

Showing the current Modero
panel firmware version and
device number

Shows NetLinx Studio
version number

FIG. 73 NetLinx Workspace window (showing panel connection via a Virtual NetLinx Master)

The panel firmware is shown on the right of the listed panel.
Download the latest firmware file from www.amx.com and then save the Kit file to
your computer.

1200V Modero Video Touch Panels

Upgrading Modero Firmware

5. If the panel firmware being used is not current, download the latest Kit file by first logging in to
www.amx.com and then navigate to Tech Center > Firmware Files and from within the Modero
section of the web page locate your Modero panel.
6. Click on the desired Kit file link and after you’ve accepted the Licensing Agreement, verify you
have downloaded the Modero Kit file to a known location.
7. From within Studio, select Tools > Firmware Transfers > Send to NetLinx Device from the Main
menu to open the Send to NetLinx Device dialog (B in FIG. 74). Verify the panel’s System and
Device number values match those values listed within the System folder in the OnLine Tree tab of
the Workspace window (A in FIG. 74).

A
B

FIG. 74 Using USB for a Virtual Master transfer

8. Select the panel’s Kit file from the Files section.
9. Enter the Device value associated with the panel and the System number associated with the Master
(listed in the OnLine Tree tab of the Workspace window). The Port field is greyed-out.
10. Click the Reboot Device checkbox. This causes the touch panel to reboot after the firmware update
process is complete. The reboot of the panel can take up 30 seconds after the firmware process has
finished.
11. Click Send to begin the transfer. The file transfer progress is indicated on the bottom-right of the
dialog (B in FIG. 74).
12. As the panel is rebooting, temporarily unplug the USB connector on the panel until the panel has
completely restarted.
13. Reconnect the USB connector to the panel.
14. Right-click the associated System number and select Refresh System. This causes a refresh of all
project systems, establishes a new connection to the Master, and populates the System list with
devices on your particular system.
15. Confirm the panel has been properly updated to the correct firmware version.

1200V Modero Video Touch Panels

Upgrading Modero Firmware

Upgrading the Modero Firmware via an IP Address
Before beginning with this section, verify that your panel is powered and connected to the NetLinx
Master through an Ethernet connection (direct or wireless).

Step 1: Prepare the Master for communication via an IP
1. Obtain the IP Address of the NetLinx Master from your System Administrator. If you do not have
an IP Address for the Master, refer to your particular Master’s instruction manual for more
information on obtaining this IP Address using NetLinx Studio 2.
From the Online Tree tab of the Workspace window, select the NetLinx Master.
Follow steps outlined in either the Obtaining or Assigning the Master’s IP Address sections
from your particular NetLinx Master instruction manual to use an address.
Note the IP Address and Gateway information.

2. Launch NetLinx Studio 2.x (default location is Start > Programs > AMX Control Disc > NetLinx
Studio 2 > NetLinx Studio 2).
3. Select Settings > Master Communication Settings from the Main menu to open the Master
Communication Settings dialog (FIG. 75).

FIG. 75 Assigning Communication Settings and TCP/IP Settings

4. Click the Communications Settings button to open the Communications Settings dialog.
5. Click on the NetLinx Master radio button (from the Platform Selection section) to indicate you are
working with a NetLinx Master (such as the NXC-ME260/64 or NI-Series of Integrated
Controllers).
6. Click on the TCP/IP radio button (from the Transport Connection Option section) to indicate you
are connecting to the Master through an IP Address.
7. Click the Edit Settings button (on the Communications Settings dialog) to open the TCP/IP
Settings dialog (FIG. 75). This dialog contains a series of previously entered IP Address/URLs and
their associated names, all of which are stored within Studio and are user-editable.

1200V Modero Video Touch Panels

Upgrading Modero Firmware

8. Click the New button to open the New TCP/IP Settings dialog where you can enter both a
previously obtained DHCP or Static IP Address and an associated description for the connection
into their respective fields.
9. Place a checkmark within the Automatically Ping the Master Controller to ensure availability radio
box to make sure the Master is initially responding online before establishing full communication.
10. Click OK to close the current New TCP/IP Settings dialog and return to the previous TCP/IP
Settings dialog where you must locate your new entry within the List of Addresses section.
11. Click the Select button to make that the currently used IP Address communication parameter.
12. Click OK to return to the Communications Settings dialog and place a checkmark within the
Authentication Required radio box if your Master has been previously secured with a
username/password.
13. Click on the Authentication Required radio box (if the Master is secured) and then press the User
Name and Password button to open the Master Controller User Name and Password dialog.
14. Within this dialog, you must enter a previously configured username and password (with sufficient
rights) before being able to successfully connect to the Master.
15. Click OK to save your newly entered information and return to the previous Communication
Settings dialog where you must click OK again to begin the communication process to your Master.
If you are currently connected to the assigned Master, a popup asks whether you
would want to temporarily stop communication to the Master and apply the new
settings.

16. Click Yes to interrupt the current communication from the Master and apply the new settings.
17. Click Reboot (from the Tools > Reboot the Master Controller dialog) and wait for the System
Master to reboot. The STATUS and OUTPUT LEDs should begin to alternately blink during the
incorporation. Wait until the STATUS LED is the only LED to blink.
18. Press Done once until the Master Reboot Status field reads *Reboot of System Complete*.
19. Click the OnLine Tree tab in the Workspace window to view the devices on the System.
The default System value is one (1).
20. Right-click the associated System number and select Refresh System. This establishes a new
connection to the specified System and populates the list with devices on that system. The
communication method is then highlighted in green on the bottom of the NetLinx Studio window.
Step 2: Prepare the panel for communication via an IP
1. Press the blue Type field (from the Master Connection section) until the choice cycles to the word
Ethernet.
2. Press the blue Mode field until the choice cycles to the word URL.
By selecting URL, the System Number field becomes read-only (grey) because the panel pulls
this value directly from the communicating target Master (virtual or not). A Virtual Master
system value can be set within the active AMX software applications such as: NetLinx Studio,
TPD4, or IREdit.

3. Press the red Master IP/URL field to open a Keyboard and enter the NetLinx Master’s IP Address
(obtained from the Diagnostics - Networking Address dialog of the NetLinx Studio
application).
4. Click Done to accept the new value and return to the System Configuration page.
5. Do not alter the Master Port Number value (this is the default value used by NetLinx).

1200V Modero Video Touch Panels

Upgrading Modero Firmware

6. Press the Back button to return to the Protected Setup page and press the on-screen Reboot button
to restart the panel and save any changes.
Step 3: Verify and Upgrade the panel firmware via an IP
1. Click the OnLine Tree tab in the Workspace window to view the devices on the System. The default
System value is one.
2. Right-click the associated System number (from the Workspace window) and select Refresh
System to detect of all devices on the current system, establish a new connection to the Master, and
refresh the System list with devices on that system.
3. After the Communication Verification dialog window verifies active communication between the
PC and the Master, verify the panel appears in the OnLine Tree tab of the Workspace window
(FIG. 76). The default Modero panel value is 10001.
Showing a Master
firmware version and
device number

Showing the current Modero
panel firmware version and
device number

Shows NetLinx Studio
version number

FIG. 76 NetLinx Workspace window (showing connected Modero panel)

The panel firmware is shown on the right of the listed panel.

4. If the panel firmware being used is not current, download the latest Kit file by first logging in to
www.amx.com and then navigate to Tech Center > Firmware Files and from within the Modero
section of the web page locate your Modero panel.
5. Click on the desired Kit file link and after you’ve accepted the Licensing Agreement, verify you
have downloaded the Modero Kit file to a known location.
6. From within Studio, select Tools > Firmware Transfers > Send to NetLinx Device from the Main
menu to open the Send to NetLinx Device dialog (FIG. 77). Verify the panel’s System and Device
number values match those values listed within the System folder in the OnLine Tree tab of the
Workspace window.
7. Select the panel’s Kit file from the Files section (FIG. 77).
8. Enter the Device value associated with the panel and the System number associated with the Master
(listed in the OnLine Tree tab of the Workspace window). The Port field is greyed-out.
9. Click the Reboot Device checkbox. This causes the touch panel to reboot after the firmware update
process is complete. The reboot of the panel can take up 30 seconds after the firmware process has
finished.
10. Click Send to begin the transfer. The file transfer progress is indicated on the bottom-right of the
dialog (FIG. 77).

1200V Modero Video Touch Panels

Upgrading Modero Firmware

Selected Firmware file

Description field for selected Kit file

Firmware download
status

Device value and System number
must match the values
listed in the Workspace window
FIG. 77 Send to NetLinx Device dialog (showing Modero firmware update via IP)

11. Click Close (after the panel reboots) to return to the main program.
12. Right-click the associated System number and select Refresh System. This causes a refresh of all
project systems, establishes a new connection to the Master, and populates the System list with
devices on your particular system.
13. Confirm the panel has been properly updated to the correct firmware version.

Upgrading Accessory Devices via the USB
The following accessory devices are firmware upgradeable:
NXA-BASE/B Battery Base (FG2255-10)
This device is not given a unique device number which would ordinarily appear within the Online Tree
tab of NetLinx Studio. It appears below the target panel which it is a part of as seen below in FIG. 78.
Target Panel Device #

NXA-BASE/B
(base version)

NetLinx Studio Online Tree tab

Accessory’s corresponding firmware page

FIG. 78 Location of Firmware version information within NetLinx Studio

1200V Modero Video Touch Panels

Upgrading Modero Firmware

The only way to upgrade the firmware of an accessory item is to send the accessory’s firmware through a
target panel. Its this panel’s device number which is entered within the Send to NetLinx Device transfer
dialog in Studio.

Step 1: Prepare the NXA-BASE/B for firmware transfer via USB
Before beginning with this section:
Unplug any connectors from the rear of the NXT panel (power, Ethernet, etc.).
Refer to the Installing the NXA-BASE/B to an NXT Modero Panel section on page 27 for
installation procedures to mount the NXT atop the battery base.
DO NOT PLACE BATTERIES IN THE BASE BEFORE CONNECTING IT TO THE
NXT PANEL. Insert batteries into the NXA-BASE/B ONLY AFTER the base has been
installed onto the bottom of the NXT panel.
Having batteries in the base before connection can damage the battery base.

Verify your NXA-BASE/B is securely attached to the bottom of the NXT panel.
Once the base is secured, side out the battery compartment and install the batteries into the
battery base. Once the batteries are installed, close the compartment.
Reconnect all rear connectors to the NXT panel.

1. Complete the instructions for configuring the NetLinx Master for IP communication found in the
Upgrading the Modero Firmware via the USB port section on page 79.
2. Press the grey Front Setup Access button for 3 seconds to open the Setup page.
3. Press the Battery Base button to open the Battery Base page (FIG. 79).

FIG. 79 Battery Base page

The battery base firmware is shown on the right of the Battery Base page.
Verify you have downloaded the latest firmware file from www.amx.com and then
save the Kit file to your computer.

1200V Modero Video Touch Panels

Upgrading Modero Firmware

Step 2: Upgrade the NXA-BASE/B firmware via USB
1. Complete the procedures outlined in the Step 1: Configure the panel for a USB Connection
Type section on page 79.
2. Prepare NetLinx Studio for communication to the panel via a Virtual Master by following the
procedures outlined in the Step 2: Prepare NetLinx Studio for communication via the USB
port section on page 80.
3. After the Communication Verification dialog window verifies active communication between the
Virtual Master and the panel, click the OnLine Tree tab in the Workspace window to view the
devices on the Virtual System. The default System value is one.
4. Right-click on the System entry and select Refresh System to re-populate the list. Verify the panel
appears in the OnLine Tree tab of the Workspace window.
The default Modero panel value is 10001.
5. Locate the latest Kit file by first logging in to www.amx.com and then navigate to Tech Center >
Firmware Files and from within the Modero section of the web page locate the Battery Base.
6. Click on the desired Kit file link and after you’ve accepted the Licensing Agreement, verify you
have downloaded the Modero Battery Base Kit file to a known location.
7. From within Studio, select Tools > Firmware Transfers > Send to NetLinx Device from the Main
menu to open the Send to NetLinx Device dialog. Verify the panel’s System and Device number
values match those values listed within the System folder in the OnLine Tree tab of the Workspace
window.
8. Select the battery base’s Kit file from the Files section.
9. Enter the Device number associated with the panel and the System number associated with the
Master (listed in the OnLine Tree tab of the Workspace window). The Port field is greyed-out.
The firmware for the battery base can not be downloaded directly. Download of the
Kit file to the BASE/1 is done through the panel.

10. Click the Reboot Device checkbox. This causes the touch panel to reboot after the firmware update
process is complete. The reboot of the panel can take up 30 seconds after the firmware process has
finished.
11. Click Send to begin the transfer. The file transfer progress is indicated on the bottom-right of the
dialog.
12. As the panel is rebooting, temporarily unplug the USB connector on the panel until the panel has
completely restarted.
13. Reconnect the USB connector to the panel.
14. Right-click the associated System number and select Refresh System. This causes a refresh of all
project systems, establishes a new connection to the Master, and populates the System list with
devices on your particular system.
15. Confirm the base has been properly updated to the correct firmware version by pressing the Battery
Base button to open the Battery Base page.

1200V Modero Video Touch Panels

Upgrading Modero Firmware

Upgrading Accessory Devices via an IP Address
The following accessory devices are firmware upgradeable:
NXA-BASE/B Battery Base (FG2255-10)
This device is not given a unique device number which would ordinarily appear within the Online Tree
tab of NetLinx Studio. It appears below the target panel which it is a part of as seen in FIG. 78 on
page 86.
The only way to upgrade the firmware of an accessory item is to send the accessory’s firmware through a
target panel. Its this panel’s device number which is entered within the Send to NetLinx Device transfer
dialog in Studio.
Firmware can also be downloaded to accessory items via a direct USB connection
using the PC as a Virtual Master. In this case, you will still need to know the System
and Device Number information of the target panel. For a more detailed description of
how to setup this type of connection, refer to the Upgrading Accessory Devices via
the USB section on page 86.

Step 1: Prepare the NXA-BASE/B for firmware transfer via an IP
Before beginning with this section:
Unplug any connectors from the rear of the NXT panel (power, Ethernet, etc.).
Refer to the Installing the NXA-BASE/B to an NXT Modero Panel section on page 27 for
installation procedures to mount the NXT atop the battery base.
DO NOT PLACE BATTERIES IN THE BASE BEFORE CONNECTING IT TO THE
NXT PANEL. Insert batteries into the NXA-BASE/B ONLY AFTER the base has been
installed onto the bottom of the NXT panel.
Having batteries in the base before connection can damage the battery base.

1. Complete the instructions for configuring the NetLinx Master for IP communication found in the
Step 1: Prepare the Master for communication via an IP section on page 83.
2. Press the grey Front Setup Access button for 3 seconds to open the Setup page.
3. Press the Battery Base button to open the Battery Base page (FIG. 80).

FIG. 80 Battery Base page

1200V Modero Video Touch Panels

Upgrading Modero Firmware

The battery base firmware is shown on the right of the Battery Base page.
Verify you have downloaded the latest firmware file from www.amx.com and then
save the Kit file to your computer.

Step 2: Upgrade the NXA-BASE/B firmware via an IP
1. Click on the OnLine Tree tab in the Workspace window to view the devices on the System.
The default System value is one.
2. Right-click the associated System number (from the Workspace) and select Refresh System to
detect of all devices on the current system, establish a new connection to the Master, and refresh the
System list with devices on that system.
3. After the Communication Verification dialog window verifies active communication between the
PC and the Master, verify the target panel appears in the OnLine Tree tab of the Workspace
window. The default Modero panel value is 10001. The NXA-BASE/B will not appear on the system
listing.
4. Locate the latest Kit file by first logging in to www.amx.com and then navigate to Tech Center >
Firmware Files and from within the Modero section of the web page locate the Modero Battery
Base section of the website.
5. Click on the desired Kit file link and after you’ve accepted the Licensing Agreement, verify you
have downloaded the Modero Battery Base Kit file to a known location.
6. From within Studio, select Tools > Firmware Transfers > Send to NetLinx Device from the Main
menu to open the Send to NetLinx Device dialog (FIG. 81). Verify the panel’s System and Device
number values match those values listed within the System folder in the OnLine Tree tab of the
Workspace window.
Selected Battery Base Firmware file

Description field for selected Kit file

Firmware download
status

Device value and System number
must match the values
listed in the Workspace window
FIG. 81 Send to NetLinx Device dialog (showing NXA-BASE/B firmware update via IP)

7. Select the battery base’s Kit file (ending in VXX.kit) from the Files section (FIG. 81).

1200V Modero Video Touch Panels

Upgrading Modero Firmware

8. Enter the Device value associated with the panel and the System number associated with the Master
(listed in the OnLine Tree tab of the Workspace window). The Port field is greyed-out.
The firmware for the battery base can not be downloaded directly. Download of the
Kit file to the BASE/B is done through the panel. The procedures for updating
firmware to the base are nearly identical to those for updating panel firmware, except
that the Kit file selected must be that of the BASE/B.

9. Click the Reboot Device checkbox. This causes the touch panel to reboot after the firmware update
process is complete. The reboot of the panel can take up 30 seconds after the firmware process has
finished.
10. Click Send to begin the transfer. The file transfer progress is indicated on the bottom-right of the
dialog (FIG. 81).
11. Click Close on the Send to NetLinx dialog window (after the panel reboots) to return to the main
program.
12. Right-click the associated System number and select Refresh System. This causes a refresh of all
project systems, establishes a new connection to the Master, and populates the System list with
devices on your particular system.
13. Press and hold the grey Front Setup Access button (below the LCD) for 3 seconds to access the
Setup page.
14. Press the Battery Base button to open the Battery Base page and confirm that the version is no
longer 0.00.
If the Base Version field displays 0.00, this means there was an error in the firmware
download process. Re-install the base firmware and re-confirm that the new base
version no longer reads 0.00.

1200V Modero Video Touch Panels

Upgrading Modero Firmware

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Firmware Pages and Descriptions
This section describes each firmware page and their specific functional elements.

Setup Navigation Buttons
These Setup Navigation Buttons (FIG. 82) appear on the left of the panel screen when the Setup page is
currently active.

Modero Setup
Navigation Buttons

FIG. 82 Setup Navigation Buttons

These Navigation Buttons are specific to these Modero panels and include the specific elements
described in the following table:
Setup Navigation Button Elements
Project Information:

Press the Project Information button to access the Project Information and view
the TPD4 project file properties currently loaded on the selected panel
(read-only).
• Refer to the Project Information Page section on page 96 for more detailed
information.

Panel Information:

Press the Panel Information button to access the Panel Information page and
view panel specific information such as resolution, memory, etc. (read-only).
• Refer to the Panel Information Page section on page 97 for more detailed
information.

Time Adjustment:

Press the Time Adjustment button to access the Time Adjustment page where
you can alter the time and date settings on the Master.
• Refer to the Time & Date Setup Page section on page 98 for more detailed
information.

Audio Adjustments:

Press the Audio Adjustments button to access the Volume page where you can
alter the audio parameters on the Modero panel.
• Refer to the Volume Page section on page 99 for more detailed information.

Protected Setup:

Press the Protected Setup button to access the Protected Setup page section
that provides access to the panel’s sensors, calibration features, and
connection settings.
• Refer to both the Protected Setup Navigation Buttons section on page 104
and Protected Setup Page section on page 105 for more detailed
information.

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Setup Navigation Button Elements (Cont.)
Video Adjustment:

Press the Video Adjustment button to access the Video Adjustment page where
you can set the video properties for incoming video.
• This button only appears on Color Video (CV) capable touch panels.
• Refer to the Video Adjustment - Video Adjustment Page section on page 101
for more detailed information.

Battery Base:

Press the Battery Base button to access the Battery Base page where you can
modify and monitor NXT-BP Modero Power Pack parameters.
• This button only appears when a Modero Table Top panel (NXT) is connected
to an NXA-BASE/B battery base.
• Refer to the Battery Base Page section on page 102 for more detailed
information.

Setup Page
This page (FIG. 83) centers around basic Modero panel properties such as: Connection Status of the
panel, Display Timeout, Inactivity Page Flip Time, Inactivity page file, and the Panel Brightness.
Connection Status
Red Connection Status icon indicates no connection to a Master
Green Connection Status icon indicates communication to a Master

Video Adjustment button doesn’t
appear on Non-Video (CA) panels
Battery Base button doesn’t appear
until NXT is connected to a BASE/B
FIG. 83 Setup page

The elements of the Setup page are described in the table below:
Setup Page Elements
Exit:

Returns you to the Main touch panel page. In this case, the previous page is the
default Main page.

Connection Status icon:

This visual display of the connection status allows the user to have a current
update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Setup Page Elements (Cont.)
Connection Status:

Displays whether the panel is communicating externally, the encryption status
of the communicating Master, what connection type is being used (Ethernet or
USB), and what System the panel is a part of.
This visual display of the connection status is also reflected at the upper-right of
each firmware page. This allows the user to have a current visual update of the
panel’s connection status regardless of what page is currently active.
• When a connection is established, the message displayed is either:
"Connected via Ethernet " or "Connected via USB ".
• If no connection can be established by the Modero panel, it will continue to try
and establish a connection while displaying: "Attempting via ...".
• The word "Encrypted" appears only when an encrypted connection is
established with a target Master.
• The panel must be rebooted before incorporating any panel communication
changes and detecting any active Ethernet connections.
The Ethernet connection is not detected until after a reboot.

Display/Panel Timeout:

Sets the length of time the panel can remain idle before activating the sleep
mode. When the device goes into sleep mode, the LCD is powered-down.
• Press the UP/DN buttons to increase/decrease the time until the panel
times out. Range = 0 - 240 minutes.
• Use this button to set the timeout value to zero and disable the sleep mode.
• Note: Display timeout values affect battery performance. Small timeout
values increase the life of the battery charge. Greater timeout values
may require more frequent battery charging.

Inactivity Page Flip
Timeout:

Sets the number of minutes of inactivity before the panel automatically flips to a
pre-selected touch panel page. When the device goes into this inactivity mode,
the LCD does not power-down.
• Press the UP/DN buttons to increase/decrease the time the panel can remain
inactive before it flips to the preset page. Range = 0 - 240 minutes.
• Use this button to set the timeout value to zero and disable the inactivity page
flip mode.
• The touch panel page used for the Inactivity page flip is shown within a small
Inactivity Page field.

Panel Brightness:

Sets the display brightness level of the panel.
• Press the UP/DN buttons to adjust the brightness level. Range = 0 - 100.
• The on-screen bargraph can be dragged to adjust the Brightness level which
is then reflected as a corresponding numeric value within the Panel
Brightness field.

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Project Information Page
The Project Information page displays the TPDesign4 (TPD4) project file properties currently loaded on
the selected Modero panel (FIG. 84). Refer to the TPDesign4 Touch Panel Program instruction manual
for more specific information on uploading TPDesign4 files to a panel.

Sample TPD4 Project Wizard dialog
FIG. 84 Project Information page (shown taking information form TPD4 project file)

The elements of the Project Information page are described in the table below:
Project Information Page Elements
Back:

Returns you to the previously active touch panel page.

Connection Status icon:

This visual display of the connection status allows the user to have a current
visual update of the panel’s connection status regardless of what page is
currently active.
• A Lock only appears on the icon if the panel has established a connection
with a currently secured target Master (requiring a username and password).

File Name:

Displays the name of the TPDesign4 project file downloaded to the panel.

Designer ID:

Displays the designer information.

File Revision:

Displays the revision number of the file.

Dealer ID:

Displays the dealer ID number (unique to every dealer and entered in TPD4).

Job Name:

Displays the job name.

Sales Order:

Displays the sales order information.

Purchase Order:

Displays the purchase order information.

Build Number:

Displays the build number information of the TPD4 software used to create the
project file.

Creation Date:

Displays the project creation date.

Revision Date:

Displays the last revision date for the project.

Last Save Date:

Displays the last date the project was saved.

Blink Rate:

Displays the feedback blink rate (10th of second).

Job Comments:

Displays any comments associated to the job. These comments are taken from
the TPD4 project file.

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Panel Information Page
The Panel Information page (FIG. 85) centers around Modero panel properties such as: resolution used,
on-board memory, firmware, address/channel information, and string information.

This information is retrieved from
the Modero panel

FIG. 85 Panel Information page (takes its’ information from the touch panel)

The elements of the Panel Information page are described in the table below:
Panel Information Page Elements
Back:

Returns you to the previously active touch panel page.

Connection Status icon:

Panel Type:

Displays the model of the Modero panel being used.

Firmware Version:

Displays the G4 firmware version being used by the panel.
• Verify you have the latest version from www.amx.com.

Setup Port:

Displays the setup port information/value being used by the panel.

High Port:

Displays the high port (port count) value for the panel.

High Address:

Displays the high address (address count) value for the panel.

High Channel:

Displays the high channel (channel count) value for the panel.

High Level:

Displays the high level (level count) value being used by the panel.

Serial Number:

Displays the specific serial number value assigned to the panel.

Setup Pages Version:

Displays the type and version of the Setup pages being used by the panel.

Screen Width:

Displays the pixel width being used to display the incoming video signal on the
Modero panel.
• Maximum available screen width on 12" panels is 800 pixels.

Screen Height:

Displays the pixel height being used to display the incoming video signal on the
Modero panel.
• Maximum available screen height on 12" panels is 600 pixels.

Screen Refresh Rate:

Displays the video refresh rate applied to the incoming video signal from the
panel.

Screen Rotation:

Displays the degree of rotation applied to the on-screen image.

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Panel Information Page Elements (Cont.)
Power Up Pages:

Displays the first touch panel page assigned for display after the device is
powered-up.
• This information is taken from the TPD4 project file.
• Most projects begin with a Main page.

Start Up String:

Displays the start-up string.

Wake Up String:

Displays the wake up string used after an activation from a timeout.

Sleep String:

Displays the sleep string used during a panel’s sleep mode.

File System:

Displays the amount of Compact Flash memory available on the Modero panel.

RAM:

Displays the available RAM (or Extended Memory module) on the Modero
panel.

Time & Date Setup Page
The Time & Date Setup page (FIG. 86) allows you to alter/set the time and date information on the
NetLinx Master. If either the Time/Date is modified on this page (then updated to the Master by pressing
the Set Time button), all devices communicating to that target Master will then be updated to reflect the
new information.

Date Display
fields
Time Display
fields

Currently
selected
FIG. 86 Time and Date Setup page

The only way to modify a panel’s time, without altering the Master, is to use NetLinx
Code.

The elements of the Time & Date Setup page are described in the table below:
Time & Date Setup Page Elements
Back:

Returns you to the previously active touch panel page without saving changes
(to save changes, use the Set Time button).

Connection Status icon:

Time Date Refresh/Set:

This section provides you with two options:
• The Get Time/Date button retrieves the Time and Date information from the
Master.
• The Set Time/Date button sets the Master to retain and save any
time/date modifications made on the Time and Date Setup page.

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Time & Date Setup Page Elements (Cont.)
Time Display fields:

• These fields display the time in three formats: STANDARD, STANDARD
AM/PM, and 24 HOUR.

Date Display fields:

• These fields display the calendar date information in several different formats.

Set Date/Time:

This section provides a user with both UP/DN arrow buttons to alter the
Master’s calendar date and time. The blue circle indicates which field is currently selected.
• Select the Year field and use the UP/DN buttons to alter the year value
(range = 2000 - 2037).
• Select the Month field and use the UP/DN buttons to alter the month value
(range = 1 - 12).
• Select the Day field and use the UP/DN buttons to alter the day value
(range = 1 - 31).
• Select the Hour field and use the UP/DN buttons to alter the hour value
(24-hour military).
• Select the Minute field and use the UP/DN buttons to alter the minute value
(range = 0 - 59).
• Select the Second field and use the UP/DN buttons to alter the second value
(range = 0 - 59).

Modero touch panels do not have an on-board clock. This page both receives and
sets the time/date of the NetLinx Master.

Volume Page
The Volume page (FIG. 87) (accessed by pressing the Audio Adjustments button on the Setup page)
allows you to adjust the master volume parameters and default panel sounds on the panel.

FIG. 87 Volume configuration page

The elements of the Volume page are described in the table below:
Volume Page Elements
Back:

Saves the changes and returns you to the previously active touch panel page.

Connection Status icon:

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Volume Page Elements (Cont.)
Master Volume:

This section allows you to alter the current master volume level:
• Use the UP/DN buttons to adjust the volume level (range = 0 - 100).
• The Master Volume bargraph indicates the current volume level.
• The Mute button toggles the Mute feature.
• The Play Test button plays a test WAV/MP3 file over the panel’s internal
speakers.

Default Panel Sounds:

Sets the Modero panel to play either the default Button Hit sound (when you
touch an active button) and/or the default Button Miss sound (when you touch
a non-active button or any area outside of the active button).

Internal Sound Level:

This section allows you to adjust the current sound level on the internal panel
speaker:
• Use the UP/DN buttons to adjust the volume output on the internal speakers
(range = 0 - 100).
• The Internal Sound Level bargraph indicates the current sound level.
• The Mute button mutes the volume.

Line In Level:

Allows you to adjust the current Line-In volume level (being received from the
communicating breakout box).
• Use the UP/DN buttons to adjust the Line-In volume level (range = 0 - 100).
• The Line-In Level bargraph indicates the current Line-In level.
• The Mute button mutes the Line-In volume.

Mic Out Level:

Allows you to adjust the current Microphone volume level (being received from
the communicating breakout box).
• Use the UP/DN buttons to adjust the Microphone volume level
(range = 0 - 100).
• The Mic Out Level bargraph indicates the current Mic Out level.

Supported sampling rates for WAV
The following is a listing of supported sampling rates associated for WAV files played on these panels.
Some WAV files currently played on Modero's may not work on these panels. The supported sampling
rates for WAV files are:
Supported WAV Sampling Rates
• 48000 Hz

• 16000 Hz

• 44100 Hz

• 12000 Hz

• 32000 Hz

• 11025 Hz

• 24000 Hz

• 8000 Hz

• 22050 Hz

Protected Setup Page
This button opens the Protected Setup page which centers around the properties used by the panel to
properly communicate with the NetLinx Master. Refer to both the Protected Setup Navigation
Buttons section on page 104 and the Protected Setup Page section on page 105 for more detailed
information.

100

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Video Adjustment Slide-Out Option Bar
Pressing the on-screen Video Adjustment button causes an option bar to slide outwards from the
Navigation buttons (FIG. 88). This option bar within a 1200V panel provides you with one choice: Video
Adjustment. The other two options (RGB Adjustment and Streaming Adjustment) are only available on
a VG-Series panel and are greyed-out (inaccessible). Each of these options corresponds to an on-board
slot position where the related components reside (as seen below). As an example: Composite video is
available via slot 1 because of the location of associated components. Since these components are shared
between the 1200V-Series and VG-Series panels, it is an option common to both. Refer to the following
section for detailed information on this option.

Slot 1

Slot 2

Slot 3

FIG. 88 Video Adjustment Slide-Out Options Bar

Video Adjustment - Video Adjustment Page
The Video Adjustment page (FIG. 89) (accessed by pressing the Video Adjustment button on the Setup
page and then selecting the appropriate button from the option bar) sets the Video properties of the
incoming video signal from an NXA-AVB/RGB Breakout Box.

Incoming Video signal
Once done making your screen
adjustments, SAVE SETTINGS.

FIG. 89 Video Adjustment page (showing default values)

The elements of the Video Adjustment page are described in the table below:
Video Adjustment Page Elements
Back:

Saves the changes and returns you to the previously active touch panel page.

Connection Status icon:

1200V Modero Video Touch Panels

101

Firmware Pages and Descriptions

Video Adjustment Page Elements (Cont.)
Settings:

• The Default Settings button sets the video settings to their default values
(indicated in this table).
• The Undo Changes button disregards any changes made on the page since
the last settings were saved.
• The Save Settings button saves any changes made to this page.

Video Settings:

• The Black & White button toggles the Black & White display mode.
Default = Off.
• The Sharpness button toggles the Interpolate (Sharpness) feature.
Default = On.
• The Interlace button toggles the Interlacing feature.
Default = On.

Status:

Displays whether or not a video-sync signal is detected.

Format:

Allows you to press this blue field and cycle through a choice of available video
formats (NTSC, PAL, SECAM, or Auto detect).
• Default = Auto.

Brightness:

Use the UP/DN buttons to alter the brightness level of the incoming signal.
• Range = 0 - 255, default = 128.

Contrast:

Use the UP/DN buttons to alter the contrast level of the incoming signal.
• Range = 0 - 255, default = 128.

Saturation:

Use the UP/DN buttons to alter the color saturation level of the incoming signal.
• Range = 0 - 255, default = 128.

Hue:

Use the UP/DN buttons to alter the hue level of the incoming signal.
• Range = 0 - 255, default = 128.

Battery Base Page
This page (FIG. 90) allows you to alter/set the power warning preferences, monitor battery status
information, and alter the display times for the battery warnings. The fields on this page are populated
with information after the panel is connected to an optional NXA-BASE/B Battery Base containing up to
two NXT-BP batteries.

FIG. 90 Battery Base page

102

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

This page is ONLY available on Modero Table Top panels (NXT) using an NXA-BASE/B. The elements
of the Battery Base page are described in the table below:
Battery Base Page Elements
Back:

Saves the changes and returns you to the previously active touch panel page.

Connection Status icon:

Charge Status:

Time Remaining (blue) indicates the amount of charge time (use) remaining
on the batteries within the connected NXA-BASE/B.
Time Until Charged (green) indicates the amount of time remaining until the
batteries installed within the connected NXA-BASE/B are fully charged.
• Range = 0:00 - 12:59. This is read in HH:MM, hours and minutes.

Panel Shutdown:

The Panel Shutdown UP/DN buttons alter the timeout value (in minutes).
• This value determines the number of minutes that would need to pass before
the panel automatically shuts-down.
• Once shutdown, the unit would have to be restarted. A zero value disables
this feature. Range = 0 - 240, default = 0 min.

Low Battery Warning:

The Low Battery Warning UP/DN buttons alter the time value (in minutes)
available on the battery (for use) before the panel displays a low battery
warning.
• Range - 10 - 45, default = 15 min.

Very Low Battery Warning: The Very Low Battery Warning UP/DN buttons alter the time value
(in minutes) available on the battery (for use) before the panel displays a very
low battery warning. This indicates a near-term panel shutdown.
Range = 3 - 15, default = 5 min.
- This value can never exceed the Low Battery Warning value.
• When the NXT-BP batteries (installed within the NXA-BASE/B battery
base) reach a point where they need to be recalibrated.
- A recalibration pop-up screen appears to ask whether or not you choose
to recalibrate the batteries at this time.
Battery Status fields:

This section provides the ability to monitor the current battery charge levels and
charge qualities:
• The Combined Charge Status bargraph indicates the combined power
charge available from both internal battery connection slots
(bargraph range = 0 - 100).
• The Battery One Charge Status bargraph indicates the power charge
available on the Slot 1 internal battery connection (bargraph range = 0 - 100).
• The Battery One Quality bargraph indicates the physical capacity (quality) of
the battery. Quality is the percentage of actual capacity vs. its rated capacity.
For optimal performance, a battery should be replaced when the quality
rating drops below 80%.
• The Battery Two Charge Status bargraph indicates the power charge
available on the Slot 2 internal battery connection (range = 0 - 100).
• The Battery Two Quality bargraph indicates the physical capacity (quality) of
the battery. Quality is the percentage of actual capacity vs. its rated capacity.
• The Base Version field indicates the firmware version being used by the
NXA-BASE/B Battery Base connected to the NXT Modero panel.
• The Battery Level Port field indicates the port being used to report the
combined charge status level back to the NetLinx Master on (set in TPD4).
• The Battery Level field indicates the level being used to report the combined
charge status level back to the NetLinx Master on (set in TPD4).

1200V Modero Video Touch Panels

103

Firmware Pages and Descriptions

Battery Base Page Elements (Cont.)
Battery Power Brightness
Limit:

The DISABLE/DISABLED button acts as a power save feature with two
available choices:
• Disable - activates the brightness limit set on the Modero panel and is used
to conserve battery power. Activating this feature causes the panel to
function at 80% of full brightness and overrides the Panel Brightness value
set on the Setup page. This extends the battery usage time.
• Disabled - (illuminated when selected) deactivates this power save feature
and makes the panel use the specified Panel Brightness level set on the
Setup page.

The term "quality" (in the context of a battery), refers to the current capacity relative to
the batteries’ rated capacity. For example, after constant use, a battery may be
operating at 75% of its rated capacity even though it might be fully charged. In this
case, the battery could be incorrectly reporting its’ information back to the battery
base and then consequently relating this information back to the Battery Base page.
A battery can be recalibrated using an optional NXT-CHG (battery charger).

Protected Setup Navigation Buttons
The Protected Setup Navigation Buttons (FIG. 91) appear on the left of the panel screen when the
Protected Setup page is currently active.

Modero Protected
Setup Navigation
Buttons

FIG. 91 Protected Setup Navigation Buttons

104

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

These Navigation Buttons are specific to these Modero panels and include the panel specific elements
described in the following table:
Protected Setup Navigation Button Elements
G4 Web Control:

Press the G4 Web Control button to access the G4 Web Control page where
you can enable or disable display and control of your panel (via the web) by a
PC running a VNC client.
• Refer to the Using G4 Web Control to Interact with a G4 Panel section on
page 74 for more detailed information.

Sensors:

Press the Sensors button to access the Sensors Setup page where you can
modify/monitor both the light and motion sensor settings.
• Refer to the Sensor Setup Page section on page 110 for more detailed
information.

Passwords:

Press the Passwords button to access the Passwords Setup page where you
can specify up to five security passwords. Default password is 1988.
• Refer to the Password Setup Page section on page 112 for more detailed
information.

Calibrate:

Press the Calibrate button to access the Calibration page where you can use
the displayed set of crosshairs to calibrate a touch panel.
• Refer to the Calibration Page section on page 113 for more detailed
information.

Wireless Settings:

Press the Wireless Settings button to access the Wireless Settings page where
you can setup the wireless connection parameters used by the
NXA-PCI80211G wireless card located within the Modero panel.
• Refer to the Wireless Settings Page section on page 114 for more detailed
information.

System Settings:

Press the System Settings button to access the System Settings page where
you can alter the communication parameters of both the NetLinx Master and
Modero panel.
• Refer to the System Settings Page section on page 118 for more detailed
information.

Protected Setup Page
The Protected Setup page (FIG. 92) centers around the properties used by the panel to properly
communicate with the NetLinx Master. Enter the factory default password (1988) into the password
keypad to access this page.

Provides access to the panel firmware
pages by enabling the grey front
setup access button:
- Setup page (after a 3 second press/hold)
- Calibration page (after a 6 second
press/hold)

FIG. 92 Protected Setup page-showing default values

1200V Modero Video Touch Panels

105

Firmware Pages and Descriptions

The elements of the Protected Setup page are described in the table below:
Protected Setup Page Elements
Back:

Saves the changes and returns you to the previously active touch panel page.

Connection Status icon:

Device Number:

Opens a keypad that is used to set and display the current device number.

Options:

Allows you to select various touch panel features:
• The Function Show button enables the display of the channel port and
channel code in the top left corner of the button, the level port and level code
in the bottom left corner, and the address port and address code in the
bottom right corner (see FIG. 94 for an example of the function locations).
• Use the Page Tracking button to toggle page tracking. When enabled, the
touch panel sends page data back to the NetLinx Master, or vice versa
depending on the touch panel settings.
• Use the Telnet button to enable or disable the telnet server on the panel. This
feature focuses on direct telnet communication to the panel.
• Use the Front Button Setup Access button to activate the grey Front Setup
Access button (located below the LCD) to access the firmware pages.
- Default condition is On.
- Press and hold this grey button for 3 seconds to access the Setup page.
- Press and hold this grey button for 6 seconds to access the Calibration
page.

Reboot Panel:

Pressing this button causes the panel to restart after saving any changes.

System Recovery:

Allows you to either reset the touch panel to factory default settings and/or wipe
out all existing touch panel pages:
• The Reset System Settings button allows a user to wipe out all current
configuration parameters on the touch panel (such as IP Addresses, Device
Number assignments, Passwords, and other presets).
- Pressing this button launches a Confirmation dialog (FIG. 93) which asks
you to confirm your selection.
- This dialog is configured with a delay timer that does not enable the YES
button for 5 seconds. This delay provides an additional amount of time for
the user to confirm their decision.
• The Remove User Pages button allows you remove all current TPD4 touch
panel pages currently on the panel (including the pre-installed AMX Demo
pages).
- Pressing this button launches a Confirmation dialog (FIG. 93) which asks
you to confirm your selection.
- This dialog is configured with a delay timer that does not enable the YES
button for 5 seconds. This delay provides an additional amount of time for
the user to confirm their decision.

106

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Protected Setup Page Elements (Cont.)
Keyboard Layout:
(build 2.60 or higher)

Displays the listing of supported international keyboard settings. The following
list allows the end-user to specify which international keyboard is being
connected to the Modero touch panel and then which characters should be
reflected within the G4 Computer Control and TakeNote applications:
- None (default), Spanish, Italian, French, German, Swiss, UK, and US
Note: You must be using a standard 101 button keyboard to accurately
utilize this feature.
• Modero uses the open-source VNC character standards to transmit the
character information to a target device such as a PC.
• One of the issues which occurred in the past was that some 101-key foreign
keyboard character sets were being incorrectly represented via the Computer
Control and Take Note applications.
• For example: Spanish keyboards consisting of Castilian character sets such
as tilde (é) were being miscommunicated by the VNC application to the
source computer and as a result, passwords were not properly being entered.
• The VNC - Computer Control keyboard drivers found in earlier Modero
firmware (build 57 or earlier) were using an English type/character set which
was not fully utilizing all available foreign characters.
• Several different countries have produced 101-key international keyboards,
each with their own unique set of keys occupying the keyboard. Several of
these keys are specific to the language they are used with.

You have a wait time of 5 seconds
before the YES option is enabled.

FIG. 93 Protected Setup page-System Recovery confirmation dialog
Channel Code
Number

Channel Port
3,132
2,8
Channel Code
Number

7,10

Address
Port

Button

Level Port

Channel Code
Number

Channel Port

Slider
Level Port

3,50

4,9
Address Code
Number

Channel Code
Number

Address
Port

1,8
Address Code
Number

FIG. 94 Button/slider Function Show example

1200V Modero Video Touch Panels

107

Firmware Pages and Descriptions

G4 Web Control Page
The G4 Web Control page (FIG. 95) centers around enabling and disabling both the display and control
of your panel (via the web). An external PC running a VNC client (installed during the initial
communication to the G4 panel) makes this possible.

FIG. 95 G4 Web Control page

Each panel supports the open standard Virtual Network Computing (VNC) interface. These panels
contain a VNC server that allows them to accept a connection from any other device running a VNC
client. Once a connection is established to that target device, the client can control the touch panel
remotely. The elements of the G4 Web Control page are described in the table below:
G4 Web Control Page Elements
Back:

Saves the changes and returns you to the previously active touch panel page.

Connection Status icon:

108

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

G4 Web Control Page Elements (Cont.)
G4 Web Control Settings:

Sets the IP communication values for the touch panel and contains:

Enable/Enabled

• The Enable/Enabled button allows you to toggle between the two G4
activation settings:
- Enable - deactivates the G4 Web Control feature on the panel.
- Enabled - activates the G4 Web Control feature on the panel and allows
an external PC running a VNC client to access the panel (after the
remaining fields are configured).

Network Interface Select

Displays the detected method of communication to the web:
• Wired is used when a direct Ethernet connection is being used for
communication to the web. This is a default setting if no wireless interface
card is detected by the panel.
• Wireless is used when a wireless card is detected within the internal card
slot. This method provides an indirect communication to the web via a
pre-configured Wireless Access Point.

Web Control Name

Allows you to enter a unique alpha-numeric string that is used as the display
name of the panel within the Manage WebControl Connections window of the
new NetLinx Security browser window.
• This Web Control tab displays a G4 icon alongside the link to the Web Control
Name given to this panel (FIG. 96).

Web Control Password

Allows you to enter the G4 Authentication session password associated for
VNC web access of this panel.

Web Control Port

Allows you to enter the port value that the VNC Web Server runs on.
• Default value is 5900.

Maximum Number of
Connections

This read-only field displays the maximum number of users that can be
simultaneously connected to the target panel via the web.
• Default value is 1.

Current Connection Count
G4 Web Control Timeout:

This read-only field displays the current number of users connected to the
target panel via the web. This value cannot exceed the Maximum number field.
Sets the length of time (in minutes) the panel can remain idle (no cursor
movements) before the session is closed and the user is disconnected.
• Minimum value = 0 minutes (panel never times-out)
• Maximum value = 240 minutes (panel times-out after 240 minutes/4hours)

FIG. 96 Sample relationship between G4 Web Control and Mange WebControl Connections window

Refer to the Using G4 Web Control to Interact with a G4 Panel section on page 74 for more detailed
instructions on how to use the G4 Web Control page with the new web-based NetLinx Security
application.

1200V Modero Video Touch Panels

109

Firmware Pages and Descriptions

Sensor Setup Page
The Sensor Setup page (FIG. 97) allows you to adjust the Light and Motion Sensor parameters on a
Modero touch panel.

FIG. 97 Sensor Setup page

A light level value between the Minimum and Maximum DIM Mode values delivers an
average light level. The DIM mode Min Level can never exceed the DIM Mode Max
Level.

The elements of the Sensor Setup page are described in the table below:
Sensor Setup Page Elements
Back:

Saves the changes and returns you to the previously active touch panel page.

Connection Status icon:

Light Sensor:

Allows you to monitor and alter the sensitivity of the Modero panel light sensor:
• The Light Sensor Level field indicates the level used to report the light
sensor level back to the NetLinx Master (set in TPD4) (read-only).
• The Light Sensor Level Port field indicates the port used to report the light
sensor level back to the NetLinx Master (set in TPD4) (read-only).
• The Light Sensor Channel field indicates the level used to report the sensor
channel back to the NetLinx Master (set in TPD4). It is On when you are
below the Maximum dim mode level (read-only).
• The Light Sensor Channel Port field indicates the port used to report the
sensor channel back to the NetLinx Master (set in TPD4) (read-only).
• The Light Level field provides a numeric value representing the current value
of the light level detected by the on-board photo-sensor.
• The Light Level bargraph displays a horizontal bargraph indicating the current
value of the light level detected by the on-board photo-sensor. This bargraph
provides a visual representation of the numeric value displayed within the
Light Level field.
• Use the Dim Mode Max Level bargraph to alter the Maximum DIM level
value used to activate the DIM Mode Brightness Level (range = 0 - 100).
• Use the Dim Mode Min Level bargraph to alter the Minimum DIM level value
used to activate the DIM Mode Brightness Level (range = 0 - 100).
- The position of this bargraph can never exceed that of the Dim Mode
Max Level.

110

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Sensor Setup Page Elements (Cont.)
Motion Sensor:

Provides the following fields:
• The Motion Detection field displays a reactive button that changes color
(illuminates) and displays the words "Motion Detected" when motion is
detected by the Modero panel’s front motion sensor.
• The Motion Sensor Port field indicates the port used to report the motion
sensor channel back to the NetLinx Master (set in TPD4) (read-only).
• The Motion Sensor Channel field indicates the channel used to report the
motion sensor channel back to the NetLinx Master (set in TPD4) (read-only).

Wake Panel On Motion
Sense:

The Wake Panel Sensitivity relates to the sensitivity of the motion sensor to
detect motion and wake the panel accordingly.
• Toggle the Enable/Enabled button to either active/inactive this feature:
- Enable - activates this feature. Activating this feature reactivates the
panel from a panel timeout (sleep) mode.
- Enabled - (illuminated when selected) deactivates this feature and
makes the panel use the specified Display Timeout value set on the
Setup Page.
• Use the Wake Panel UP/DN buttons to alter the sensitivity value.
- Range = 0 - 100.
• The horizontal WAKE PANEL SENSITIVITY bargraph indicates the current
motion sensitivity value associated with waking the panel from a timeout.

Dim Mode Minimum
Brightness:

Allows you to alter the sensitivity of the Modero panel light sensor:
• Toggle the Enable/Enabled button to either active/inactive the DIM Mode
feature:
- Enable - activates this feature. Once active (by receiving a value below the
Dim Mode Min Level value), the current light level ramps to the DIM Mode
value within a few seconds.
- Enabled - (illuminated when selected) deactivates this feature.
• Use the DIM Mode Brightness UP/DN buttons to alter the DIM level.
- Range = 0 - 100.
- The lower the value, the darker a room must be before the LCD Brightness
value changes to conform to a DIM room (and vice versa with a
higher value).
• The DIM Mode Minimum Brightness bargraph indicates the current DIM
Mode Brightness level.
- This level corresponds to the brightness level of the LCD used when
the DIM Mode is active.
- The Brightness value of the panel in a DIM room (low-light) is much
less than that of a Non-DIM (well to brightly-lit) where the LCD Brightness
must be higher to display the screen content clearly.

There is a relationship between the motion sensor and the panel sleep feature. If a
panel is set to Sleep Mode, there is a time delay before the motion sensor is activated
to detect motion. By creating a time delay to the detection, this allows a user to set
the sleep mode and leave the panels’ detection range. In this way, the panel doesn’t
awake immediately after the sleep is active and you move away.

Using the Automated Brightness Control feature (DIM Mode)
Please follow the steps below to set up Automated Brightness Control:

1. Set the lighting conditions in the room to maximum (turn On all the lights).
2. Set the Maximum Panel Brightness, from the Setup page, to a comfortable level.
Sitting in front of the panel, you should be able to comfortably see someone sitting
behind the panel without being “blinded” by the panel.

1200V Modero Video Touch Panels

111

Firmware Pages and Descriptions

3. Open the Sensors Setup page (FIG. 97 on page 110) from the Protected Setup menu section.
4. Move around the panel and block the direct or indirect light from the room fixtures with your body.
Take note of the drop in the lighting level being detected by the panel in response to your
movements.
5. Set the Maximum brightness of the Dimmer (Dim Mode Max Level) below the detected drop. This
will make sure that the panel does not react to variations in the lighting conditions of a normal
working environment.
The maximum (upper level) of the dimmer should be at least 15% lower than the
maximum detected level.

6. Set the minimum lighting conditions in the room (not complete darkness but the minimal lighting
setup, unless complete darkness is an “operational option” for the room).
7. Set the Minimum Dimmer Brightness (Dim Mode Min Level) to a comfortable level by sitting in
front of the panel. You should be able to comfortably see someone sitting behind the panel without
being “blinded” by the panel.
8. Move around the panel and block the direct or indirect light from the room fixtures with your body.
Take note of the drop in the lighting level being detected by the panel in response to your
movements.
9. Set the Minimum brightness of the Dimmer (Dim Mode Max Level) below the detected drop. This
will make sure that the panel does not react to variations in the lighting conditions of a normal
working environment.
The minimum (lower level) of the dimmer should be at least 10% lower than the
minimum detected level (ex: lower dimmer level at 30% if the detected lighting of the
room is at 40%).

Password Setup Page
The Password Setup page (FIG. 98) centers around the properties used to assign passwords for the
Modero panel pages.

FIG. 98 Password Setup page

112

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

The elements of the Password Setup page are described in the table below:
Password Setup Page Elements
Back:

Saves the changes and returns you to the previously active touch panel page.

Connection Status icon:

In Panel Password
Change:

Accesses the alphanumeric values associated to particular password sets.
• PASSWORD 1, 2, 3, 4, 5 (protected) buttons open a keyboard where you can
enter alphanumeric values associated to a selected password group.
• Clearing Password #5 removes the need to enter a password before
accessing the Protected Setup page.

Calibration Page
This page (FIG. 99) allows you to calibrate the input touch device (touch panel) using the
pre-selected touch driver.
Press and hold the grey Front Setup Access button (below the Modero LCD) for
6 seconds to access the Calibration page.
Press the crosshairs to calibrate the panel and return to the last active firmware page.

FIG. 99 Calibration page (actually 3 separate screens)

If the calibration was improperly set and you cannot return to the Calibration
page (through the panel’s firmware); you can access this firmware page via
G4 WebControl where you can navigate to the Protected Setup page and press the
Calibrate button through your VNC window.
This action causes the panel to go to the Calibration page seen above, where you
can physically recalibrate the actual touch panel again using the above procedures.

1200V Modero Video Touch Panels

113

Firmware Pages and Descriptions

Wireless Settings Page
The Wireless Settings page (FIG. 100) sets the communication information for the installed wireless
interface card. This information includes its corresponding IP communication parameters, wireless
communication settings, and read the device number assigned to the Modero panel. These panels can use
the NXA-PCI80211G wireless card for wireless communication. This card also supports Wired
Encryption Protocol (WEP) encryption of 64-bit and 128-bit key lengths. Refer to both the Wireless
Settings Page - Wireless Access Overview section on page 59 and Configuring a Wireless
Connection section on page 60 for more detailed information of setting up the Modero panel for wireless
network access.

IP Settings section
Wireless Settings section

Red fields are user-editable
Blue fields cycle through choices
Grey fields are read-only

FIG. 100 Wireless Settings page (showing default values)

The elements of the Wireless Settings page are described in the table below:
Wireless Settings Page Elements
Back:

Saves the changes and returns you to the previously active touch panel page.

Connection Status icon:

IP Settings:
DHCP/STATIC

Sets the IP communication values for the touch panel and contains:
Sets the panel to either DHCP or Static communication modes.
• DHCP (Dynamic Host Configuration Protocol) assigns IP Addresses to client
stations logging onto a TCP/IP network from a DHCP server.
• Static IP is a permanent IP Address that is assigned to a node in a TCP/IP
network.
Note: If DHCP is selected, the following fields become read-only: IP Address,
Subnet Mask, Gateway, Primary DNS, Secondary DNS, and Domain.

IP Address

Sets the secondary IP Address assigned to the panel.

Subnet Mask

Sets a subnetwork address to the panel.
• Subnetwork mask is the technique used by the IP protocol to filter messages
into a particular network segment (subnet).

114

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Wireless Settings Page Elements (Cont.)
IP Settings (Cont.):
Gateway

Sets a gateway value to the panel.
• Gateway is a computer that either performs protocol conversion between
different types of networks/applications or acts as a go-between for two or
more networks that use the same protocols.

Host Name

Sets the host name of the panel.
• PRIMARY DNS sets the address of the primary DNS server being used by the
Modero panel for host name lookups.
- DNS (Domain Name System) is software that lets users locate computers
on a local network or the Internet (TCP/IP network) by host and domain. The
DNS server maintains a database of host names for its’ domain and their
corresponding IP Addresses.
• SECONDARY DNS sets the secondary DNS value to the panel.

Primary DNS

Sets the address of the primary DNS server used by the panel for host name
lookups.

Secondary DNS

Sets the secondary DNS value to the Modero panel.

Domain

Sets the unique name on the Internet to the panel for DNS look-up.

MAC Address

This value is factory set by the manufacturer of the wireless mini-PCI Ethernet
card.

Access Point MAC
Address:

This value is factory set by the manufacturer of the Wireless Access Point
(WAP).
• When communicating with a WAP200G enter the MAC Address (BSSID) of
the target WAP as the Access Point MAC Address. Refer to the WAP200G
Instruction Manual for more detailed information on the interaction between
these two product lines.

Wireless Settings:
Network Name (SSID)

Sets the communication values for the NXA-PCI80211G mini-PCI wireless
communication card installed within the Modero panel.
Provides the Service Set Identifier (SSID), required by the panel, before it is
permitted to join the wireless network. The SSID is the unique name used on
the WAP and assigned to all panels in a wireless network that are communicating to the same target WAP.
• It is case sensitive and must not exceed 32 characters, which may be any
keyboard character. Make sure this setting is the same for all points in your
wireless network.
• This unique string identifies the network and is the same string for all users on
the same network.

Authentication

Toggles between the two authentication modes: Open System or Shared Key:
• An Open system network allows connections from any client without
authenticating whether that client has permission to associate with the
network.
• A Shared key network requires the client to submit a key which is shared by
the network Wireless Access Point before it is given permission to associate
with the network. In this case the key is the same as the WEP encryption
key.
• In both cases, even after association has taken place, if WEP encryption has
also been enabled then the client will still require the WEP key to encrypt and
decrypt packets in order to communicate successfully with the network.

1200V Modero Video Touch Panels

115

Firmware Pages and Descriptions

Wireless Settings Page Elements (Cont.)
Wireless Settings (Cont.):
Encryption

Cycles through the available encryption options: Clear Text, WEP64, and
WEP128. Wired Equivalent Privacy is an 802.11 security protocol for wireless
networks. The WEP encryption method is designed to provide the "equivalent"
security available in wireline networks.
• Clear Text causes network packets to be sent out as unencrypted text.
• WEP64 enables WEP encryption at 64-bits. In this case all packets will be
transmitted with their contents encrypted using the Default WEP Key.
• WEP128 enables WEP encryption at 128-bits. All packets are transmitted
with their contents encrypted using the Default WEP Key.
• If the key is not the correct size, the system will resize it to match the number
of bits required for the WEP encryption mode selected.

Generate (Passphrase)

Pressing the Generate button displays an on-screen keyboard which allows
you to enter a passphrase and then AUTOMATICALLY generate all four WEP
keys which are compatible only among Modero panels.
• Note: The code key generator on Modero panels use the same key
generation formula. Therefore, this same Passphrase generates identical
keys when done on any Modero because they all use the same
Modero-specific generator. The Passphrase generator is case sensitive.
• Take these WEP keys and enter them into the target WAP. When also working
with multiple panels, these WEP Keys (identical across all Modero panels)
must be entered manually into the target WAP.
• Once all panels have been setup in this way, these WEP keys can then be
entered into the associated Wireless Access Point for ease of installation.
• The Passphrase generator is unique to Modero panels. The Key generator on
these Modero panels are specific and do not generate the same keys as
other external non-AMX wireless devices.
- Example: If you enter the word apple into the Passphrase generator on a
3rd-party Wireless Access Point, it comes back with 1a:2b:3c:4d:etc.
Entering the same apple in the Passphrase generator of any Modero panel
generates a different key: a1:b2:c3:d4:etc. Only AMX Modero panels
generate the same Current Key by using a unique Passphrase key
generation technology. A Current Key string, when generated anywhere
else, will not match those created on the Modero panels.
Note: The code key generator on Modero panels use the same key generation
formula.The passphrase generator is case sensitive.

Default Key

Cycles through the four available WEP key identifiers in order to select a WEP
key to use. As the Default Key value is altered (through selection) the
corresponding Current Key is displayed. Each of these corresponds to a WEP
key.
• This feature is useful for accessing different networks without having to
re-enter that networks’ WEP key.
• It is also sometimes used to set up a rotating key schedule to provide an extra
layer of security.

116

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

Wireless Settings Page Elements (Cont.)
Wireless Settings (Cont.):
WEP Keys

This feature provides you with another level of security by selecting a Key
value.
• A single button is available for each WEP key up to a maximum of four keys.
• Pushing any of these buttons brings up an on-screen keyboard. Keys should
be entered in hexadecimal notation. It is common practice for every two
characters (representing a single byte) to be separated by a colon.
• Press Done to accept any changes and save the new value.
• Ex: 01:0A:67:F3:56, although this is not necessary and the key may be
entered by omitting the colons. A 64-bit key will be 10 characters in length
while a 128-bit key will be 26 characters in length. The length of the key
entered determines the level of WEP encryption employed.
Either 64-bit or 128-bit.
• 128-bit keys may also be entered and are used if supported by the internal
wireless card.

Current Key

Displays the current WEP key in use. Keys may also be examined by touching
the key buttons and noting the keyboard initialization text.
• When working with a single panel and a single WAP, it is recommended that
you manually enter the Current Key from the WAP into the selected WEP
Key.
• When working with a single WAP and multiple panels, it is recommended that
you generate a Current Key using the same passphrase on all panels and
then enter the panel-produced WEP key manually into the Wireless Access
Point.

Channel

The RF channel being used for connection to the WAP (read -only).
• This is determined through the WAP.

Link Quality

Displays the current quality of the link (as descriptive colored text) from the
wireless NIC to the Wireless Access Point in real time.
• The bargraph has been replaced with a descriptions: None, Poor, Fair,
Good, Very Good, and Excellent. Green color text indicates better
communication quality.
• It reports the quality of the signal over the air (direct sequence spread
spectrum). Even when the link quality is at its lowest you still have a
connection and with it the ability to transmit and receive data, even if at much
lower speeds.
Note: Both Link Quality and Signal Strength are applicable to the RF
connection only. It is quite possible to have an RF signal to a Wireless Access
Point but be unable to communicate with it because of either incorrect IP or
encryption settings.

Signal Strength

SNR (Signal Noise Ratio) is a measure of the relative strength of a wireless RF
connection. This indicator displays a description of the signal strength from the
Wireless Access Point connection.
• The bargraph has been replaced with a descriptions: None, Poor, Fair,
Good, Very Good, and Excellent. Green color text indicates better signal
strength.
• Given this value and the link quality above, a user can determine the noise
level component of SNR.
Ex: If the signal strength is high but the link quality is low then the cause of the
link degradation is noise. However, if the signal strength is low and the link
quality is low the cause would simply be signal strength.

1200V Modero Video Touch Panels

117

Firmware Pages and Descriptions

Wireless Settings Page Elements (Cont.)
Wireless Settings (Cont.):
Data Rate

The data rate (in Mbps) at which the panel is currently communicating with a
target WAP at (dynamic).
• As you move closer to the target WAP (and both the signal strength/
quality), the data rate increases and as the quality degrades this rate
decreases.
• Data rates for 802.11g communication are: 1, 2, 5.5, 11, and 54 Mbps.
• Ex: 802.11g has a max data rate is 54 Mbps.

System Settings Page
The System Settings page (FIG. 101) sets the Secondary DNS Address information with its
corresponding IP communication parameters, NetLinx Master communication settings, and reads the
device number assigned to the Modero panel.

IP Settings section
Master Connection section
(NetLinx Master properties)
Master Connection features are not
saved until the panel is rebooted

Red fields are user-editable
Blue fields cycle through choices
Grey fields are read-only
FIG. 101 System Settings page showing default values (reads and assigns values to the panel and Master)

The elements of the System Settings page are described in the table below:
System Settings Page Elements
Back:

Saves the changes and returns you to the previously active touch panel page.

Connection Status icon:

IP Settings:
DHCP/Static

Sets the IP communication values for the panel and contains:
Sets the panel to either DHCP or Static communication modes.
• DHCP (Dynamic Host Configuration Protocol) assigns IP Addresses from
client stations logging onto a TCP/IP network via a DHCP server.
• Static IP is a permanent IP Address that is assigned to a node in a TCP/IP
network.

IP Address

Sets the secondary IP Address assigned to the panel.

Subnet Mask

Sets a subnetwork address to the panel.
• Subnetwork mask is the technique used by the IP protocol to filter messages
into a particular network segment (Subnet).

118

1200V Modero Video Touch Panels

Firmware Pages and Descriptions

System Settings Page Elements (Cont.)
Wireless Settings (Cont.):
Gateway

Sets a gateway value to the panel.
• Gateway is a computer that either performs protocol conversion between
different types of networks/applications or acts as a go-between two or more
networks that use the same protocols.

Host Name

Sets the host name of the panel.

Primary DNS

Sets the address of the primary DNS server used for host name lookups.
• DNS (Domain Name System) is software that lets users locate computers on
a local network or the Internet (TCP/IP network) by host and domain. The
DNS server maintains a database of host names for its’ domain and their
corresponding IP Addresses.

Secondary DNS

Sets a secondary DNS value to the panel.

Domain

Sets the unique name on the Internet to the panel for DNS look-up.
• The panel belongs to the DNS domain.

Ethernet Mode

Sets the speed of the Ethernet connection to the panel.
• Choices are: Auto, 10 Half Duplex, 10 Full Duplex, 100 Half Duplex, or
100 Full Duplex.

MAC Address
Master Connection:
Type

Displays a read-only field that is factory set by AMX for the built-in Ethernet
interface.
Sets the NetLinx Master communication values:
Sets the NetLinx Master to communicate with the panel via either USB or
Ethernet. This is based on the cable connection from the rear.
ICSNet is not a supported option on this panel.
• Ethernet is a CAT-5 cable (10/100Base T terminated in an RJ-45 connector)
used to network computers together and is used in most LAN (local area
networks). This description is also used to refer to both wired and wireless
communication.
• USB option cannot be used on Modero panels which are not equipped with a
rear USB port.

Mode

Cycles between the different connection modes (URL, Listen, and Auto)
(ETHERNET Only - disabled when USB is selected)
• URL - In this mode, enter the IP/URL, Master Port Number, and
username/password (if used) on the Master.
- The System Number field is read-only because the panel obtains this
information from the communicating Master.
• Listen - In this mode, add the Modero panel address into the URL List in
NetLinx Studio and set the connection mode to Listen. This mode allows the
Modero touch panel to "listen" for the Master’s communication signals.
- The System Number and Master IP/URL fields are red-only.
• Auto - In this mode, enter the System Number and a username/password
(if applicable). This mode is used when both the panel and the NetLinx
Master are on the same Subnet and the Master has its UDP feature enabled.
- Master IP/URL field is read-only.

System Number

Allows you to enter a system number. Default value is 0 (zero).
(ETHERNET Only - disabled when USB is selected)

Master IP/URL

Sets the Master IP or URL of the NetLinx Master.
(ETHERNET Only - disabled when USB is selected)

Master Port Number

Allows you to enter the port number used with the NetLinx Master.
• Default value is 1319. (ETHERNET Only - disabled when USB is selected)

Username/Password

1200V Modero Video Touch Panels

If the target Master has been previously secured, enter the alpha-numeric string
(into each field) assigned to a pre-configured user profile on the Master.
This profile should have the pre-defined level of access/configuration rights.

119

Firmware Pages and Descriptions

Refer to the Step 2: Choosing a Master Connection Mode Setting section on page 68 for more detailed
information on using the System Settings page.

120

1200V Modero Video Touch Panels

Programming

Programming
You can program the touch panel, using the commands in this section, to perform a wide variety of
operations using Send_Commands and variable text commands.
A device must first be defined in the NetLinx programming language with values for the Device:
Port: System (in all programming examples - Panel is used in place of these values and represents all
Modero panels).

Verify you are using the latest NetLinx Master and Modero touch panel firmware.
Verify you are also using the latest version of TPDesign4.

Button Assignments
• Button Channel Range: 1 - 4000 Button push and Feedback (per address port)
• Button Variable Text range: 1 - 4000 (per address port)
• Button States Range: 1 - 256
(0 = All states, for General buttons 1 = Off state and 2 = On state).
• Level Range: 1 - 600 (Default level value 0 - 255, can be set up to 1 - 65535)
• Address port Range: 1 - 100

These button assignments can only be adjusted in TPD4 and not on the panels
themselves.

Page Commands
These Page Commands are used in NetLinx Programming Language and are case insensitive.
Page Commands
@APG
Add a specific
popup page to a
specified popup
group.

Add the popup page to a group if it does not already exist. If the new popup is added to a
group which has a popup displayed on the current page along with the new pop-up, the
displayed popup will be hidden and the new popup will be displayed.
Syntax:
"'@APG-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
popup group name = 1 - 50 ASCII characters. Name of the popup group.
Example:
SEND_COMMAND Panel,"'@APG-Popup1;Group1'"
Adds the popup page ’Popup1’ to the popup group ’Group1’.

@CPG

Syntax:

Clear all popup
pages from
specified popup
group.

Variable:

"'@CPG-'"

popup group name = 1 - 50 ASCII characters. Name of the popup group.
Example:
SEND_COMMAND Panel,"'@CPG-Group1'"
Clears all popup pages from the popup group ’Group1’.

1200V Modero Video Touch Panels

121

Programming

Page Commands (Cont.)
@DPG

Syntax:

Delete a specific
popup page from
specified popup
group if it exists.

Variable:

"'@DPG-;'"

popup page name = 1 - 50 ASCII characters. Name of the popup page.
popup group name = 1 - 50 ASCII characters. Name of the popup group.
Example:
SEND_COMMAND Panel,"'@DPG-Popup1;Group1'"
Deletes the popup page ’Popup1’ from the popup group ’Group1’.

If the flag is set, the popup will return to its default location on show instead of its last drag
location.
Set the popup
location reset flag. Syntax:
@PDR

"'@PDR-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
reset flag = 1 = Enable reset flag
0 = Disable reset flag
Example:
SEND_COMMAND Panel,"'@PDR-Popup1;1'"
Popup1 will return to its default location when turned On.
@PHE

Syntax:

"'@PHE-;'"
Set the hide effect
for the specified
Variable:
popup page to the
named hide effect. popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
hide effect name = Refers to the popup effect names being used.
Example:
SEND_COMMAND Panel,"'@PHE-Popup1;Slide to Left'"
Sets the Popup1 hide effect name to ’Slide to Left’.
@PHP
Set the hide effect
position.

Only 1 coordinate is ever needed for an effect; however, the command will specify both.
This command sets the location at which the effect will end at.
Syntax:
"'@PHP-;,'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
Example:
SEND_COMMAND Panel,"'@PHP-Popup1;75,0'"
Sets the Popup1 hide effect x-coordinate value to 75 and the y-coordinate value to 0.

@PHT
Set the hide effect
time for the
specified popup
page.

Syntax:
"'@PHT-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
hide effect time = Given in 1/10ths of a second.
Example:
SEND_COMMAND Panel,"'@PHT-Popup1;50'"
Sets the Popup1 hide effect time to 5 seconds.

122

1200V Modero Video Touch Panels

Programming

Page Commands (Cont.)
@PPA
Close all popups
on a specified
page.

If the page name is empty, the current page is used. Same as the ’Clear Page’ command
in TPDesign4.
Syntax:
"'@PPA-'"
Variable:
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'@PPA-Page1'"
Close all popups on Page1.

@PPF
Deactivate a
specific popup
page on either a
specified page or
the current page.

If the page name is empty, the current page is used (see example 2). If the popup page is
part of a group, the whole group is deactivated. This command works in the same way as
the ’Hide Popup’ command in TPDesign4.
Syntax:
"'@PPF-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'@PPF-Popup1;Main'"
Deactivates the popup page ’Popup1’ on the Main page.
Example 2:
SEND_COMMAND Panel,"'@PPF-Popup1'"
Deactivates the popup page ’Popup1’ on the current page.

@PPG
Toggle a specific
popup page on
either a specified
page or the current page.

If the page name is empty, the current page is used (see example 2). Toggling refers to the
activating/deactivating (On/Off) of a popup page. This command works in the same way
as the ’Toggle Popup’ command in TPDesign4.
Syntax:
"'@PPG-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'@PPG-Popup1;Main'"
Toggles the popup page ’Popup1’ on the ’Main’ page from one state to another (On/Off).
Example 2:
SEND_COMMAND Panel,"'@PPG-Popup1'"
Toggles the popup page ’Popup1’ on the current page from one state to another (On/Off).

@PPK
Kill a specific
popup page from
all pages.

Kill refers to the deactivating (Off) of a popup window from all pages. If the pop-up page is
part of a group, the whole group is deactivated. This command works in the same way as
the 'Clear Group' command in TPDesign 4.
Syntax:
"'@PPK-'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
Example:
SEND_COMMAND Panel,"'@PPK-Popup1'"
Kills the popup page ’Popup1’ on all pages.

1200V Modero Video Touch Panels

123

Programming

Page Commands (Cont.)
@PPM
Set the modality
of a specific
popup page to
Modal or
NonModal.

A Modal popup page, when active, only allows you to use the buttons and features on that
popup page. All other buttons on the panel page are inactivated.
Syntax:
"'@PPM-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
mode = NONMODAL converts a previously Modal popup page to a NonModal.
MODAL converts a previously NonModal popup page to Modal.
modal = 1 and non-modal = 0
Example:
SEND_COMMAND Panel,"'@PPM-Popup1;Modal'"
Sets the popup page ’Popup1’ to Modal.
SEND_COMMAND Panel,"'@PPM-Popup1;1'"
Sets the popup page ’Popup1’ to Modal.

@PPN
Activate a
specific popup
page to launch on
either a specified
page or the
current page.

If the page name is empty, the current page is used (see example 2). If the popup page is
already on, do not re-draw it. This command works in the same way as the ’Show Popup’
command in TPDesign4.
Syntax:
"'@PPN-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'@PPN-Popup1;Main'"
Activates ’Popup1’ on the ’Main’ page.
Example 2:
SEND_COMMAND Panel,"'@PPN-Popup1'"
Activates the popup page ’Popup1’ on the current page.

@PPT

If timeout is empty, popup page will clear the timeout.

Set a specific
popup page to
timeout within a
specified time.

Syntax:
"'@PPT-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
timeout = Timeout duration in 1/10ths of a second.
Example:
SEND_COMMAND Panel,"'@PPT-Popup1;30'"
Sets the popup page ’Popup1’ to timeout within 3 seconds.

@PPX

This command works in the same way as the 'Clear All' command in TPDesign 4.

Close all
popups on all
pages.

Syntax:
"'@PPX'"
Example:
SEND_COMMAND Panel,"'@PPX'"
Close all popups on all pages.

124

1200V Modero Video Touch Panels

Programming

Page Commands (Cont.)
@PSE
Set the show
effect for the
specified popup
page to the
named show
effect.

Syntax:
"'@PSE-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
show effect name = Refers to the popup effect name being used.
Example:
SEND_COMMAND Panel,"'@PSE-Popup1;Slide from Left'"
Sets the Popup1 show effect name to ’Slide from Left’.

@PSP
Set the show
effect position.

Only 1 coordinate is ever needed for an effect; however, the command will specify both.
This command sets the location at which the effect will begin at.
Syntax:
"'@PSP-;,'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
Example:
SEND_COMMAND Panel,"'@PSP-Popup1;100,0'"
Sets the Popup1 show effect x-coordinate value to 100 and the y-coordinate value to 0.

@PST
Set the show
effect time for the
specified popup
page.

Syntax:
"'@PST-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed
On.
show effect time = Given in 1/10ths of a second.
Example:
SEND_COMMAND Panel,"'@PST-Popup1;50'"
Sets the Popup1 show effect time to 5 seconds.

PAGE
Flip to a specified
page.

Flips to a page with a specified page name. If the page is currently active, it will not redraw
the page.
Syntax:
"'PAGE-'"
Variable:
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'PAGE-Page1'"
Flips to page1.

1200V Modero Video Touch Panels

125

Programming

Page Commands (Cont.)
PPOF
Deactivate a
specific popup
page on either a
specified page or
the current page.

If the page name is empty, the current page is used (see example 2). If the popup page is
part of a group, the whole group is deactivated. This command works in the same way as
the ’Hide Popup’ command in TPDesign4.
Syntax:
"'PPOF-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'PPOF-Popup1;Main'"
Deactivates the popup page ’Popup1’ on the Main page.
Example 2:
SEND_COMMAND Panel,"'PPOF-Popup1'"
Deactivates the popup page ’Popup1’ on the current page.

PPOG
Toggle a specific
popup page on
either a specified
page or the
current page.

If the page name is empty, the current page is used (see example 2). Toggling refers to the
activating/deactivating (On/Off) of a popup page. This command works in the same way
as the ’Toggle Popup’ command in TPDesign4.
Syntax:
"'PPOG-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'PPOG-Popup1;Main'"
Toggles the popup page ’Popup1’ on the Main page from one state to another (On/Off).
Example 2:
SEND_COMMAND Panel,"'PPOG-Popup1'"
Toggles the popup page ’Popup1’ on the current page from one state to another (On/Off).

PPON
Activate a
specific popup
page to launch on
either a specified
page or the
current page.

If the page name is empty, the current page is used (see example 2). If the popup page is
already On, do not re-draw it. This command works in the same way as the ’Show Popup’
command in TPDesign4.
Syntax:
"'PPON-;'"
Variable:
popup page name = 1 - 50 ASCII characters. Name of the popup page.
page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Panel,"'PPON-Popup1; Main'"
Activates the popup page ’Popup1’ on the Main page.
Example 2:
SEND_COMMAND Panel,"'PPON-Popup1'"
Activates the popup page ’Popup1’ on the current page.

126

1200V Modero Video Touch Panels

Programming

Programming Numbers
The following information provides the programming numbers for colors, fonts, and borders.
Colors can be used to set the colors on buttons, sliders, and pages. The lowest color number represents
the lightest color-specific display; the highest number represents the darkest display.
For example, 0 represents light red, and 5 is dark red.

RGB triplets and names for basic 88 colors
RGB Values for all 88 Basic Colors
Index No. Name

Red

Green

Blue

Very Light Red

255

Light Red

223

Red

191

Medium Red

159

Dark Red

127

Very Dark Red

Very Light Orange

255

128

Light Orange

223

112

Orange

191

Medium Orange

159

Dark Orange

127

Very Dark Orange

Very Light Yellow

255

Light Yellow

223

Yellow

191

Medium Yellow

159

Dark Yellow

127

Very Dark Yellow

Very Light Lime

128

255

Light Lime

112

223

Lime

191

Medium Lime

159

Dark Lime

127

Very Dark Lime

Very Light Green

255

Light Green

223

Green

191

Medium Green

159

Dark Green

127

Very Dark Green

Very Light Mint

255

128

Light Mint

223

112

Mint

191

Medium Mint

159

Dark Mint

127

Very Dark Mint

1200V Modero Video Touch Panels

127

Programming

RGB Values for all 88 Basic Colors (Cont.)

128

Index No. Name

Red

Green

Blue

Very Light Cyan

255

Light Cyan

223

Cyan

191

Medium Cyan

159

Dark Cyan

127

Very Dark Cyan

Very Light Aqua

128

255

Light Aqua

112

223

Aqua

191

Medium Aqua

159

Dark Aqua

127

Very Dark Aqua

Very Light Blue

255

Light Blue

223

Blue

191

Medium Blue

159

Dark Blue

127

Very Dark Blue

Very Light Purple

128

255

Light Purple

112

223

Purple

191

Medium Purple

159

Dark Purple

127

Very Dark Purple

Very Light Magenta

255

Light Magenta

223

Magenta

191

Medium Magenta

159

Dark Magenta

127

Very Dark Magenta

Very Light Pink

255

128

Light Pink

223

112

Pink

191

Medium Pink

159

Dark Pink

127

Very Dark Pink

White

255

Grey1

238

Grey3

204

Grey5

170

Grey7

136

Grey9

102

Grey4

187

Grey6

153

1200V Modero Video Touch Panels

Programming

RGB Values for all 88 Basic Colors (Cont.)
Index No. Name

Red

Green

Blue

Grey8

119

Grey10

Grey12

Grey13

Grey2

221

Grey11

Grey14

Black

255

TRANSPARENT

Font styles and ID numbers
Font styles can be used to program the text fonts on buttons, sliders, and pages. The following chart
shows the default font type and their respective ID numbers generated by TPDesign4.
Default Font Styles and ID Numbers
Font ID # Font type

Size

Font ID # Font type

Size

Courier New

Arial

Courier New

Arial

Courier New

Arial

Courier New

Arial

Courier New

Arial

Courier New

Arial

Courier New

Arial

Courier New

Arial

AMX Bold

Arial

AMX Bold

Arial Bold

AMX Bold

Arial Bold

32 - Variable Fonts start at 32.

You must import fonts into a TPDesign4 project file. The font ID numbers are
assigned by TPDesign4. These values are also listed in the
Generate Programmer’s Report.

1200V Modero Video Touch Panels

129

Programming

Border styles
The TPDesign4 Touch Panel Design program has pre-set border styles that are user selectable. TPD4
border styles can ONLY be changed by using the name.
TPD4 Border Styles by Name

130

Border styles

None

Diamond 55

AMX Elite -L

Diamond 65

AMX Elite -M

Diamond 75

AMX Elite -S

Double Bevel -L

Bevel -L

Double Bevel -M

Bevel -M

Double Bevel -S

Bevel -S

Double Line

Circle 15

Fuzzy

Circle 25

Glow-L

Circle 35

Help Down

Circle 45

Help Down Reversed

Circle 55

Menu Bottom Rounded 15

Circle 65

Menu Bottom Rounded 25

Circle 75

Menu Bottom Rounded 35

Circle 85

Menu Bottom Rounded 45

Circle 95

Menu Bottom Rounded 55

Circle 105

Menu Bottom Rounded 65

Circle 115

Menu Bottom Rounded 75

Circle 125

Menu Bottom Rounded 85

Circle 135

Menu Bottom Rounded 95

Circle 145

Menu Bottom Rounded 105

Circle 155

Menu Bottom Rounded 115

Circle 165

Menu Bottom Rounded 125

Circle 175

Menu Bottom Rounded 135

Circle 185

Menu Bottom Rounded 145

Circle 195

Menu Bottom Rounded 155

Cursor Bottom

Menu Bottom Rounded 165

Cursor Bottom with Hole

Menu Bottom Rounded 175

Cursor Top

Menu Bottom Rounded 185

Cursor Top with Hole

Menu Bottom Rounded 195

Cursor Left

Menu Left Rounded 15

Cursor Left with Hole

Menu Left Rounded 25

Cursor Right

Menu Left Rounded 35

Cursor Right with Hole

Menu Left Rounded 45

Custom Frame

Menu Left Rounded 55

Diamond 15

Menu Left Rounded 65

Diamond 25

Menu Left Rounded 75

Diamond 35

Menu Left Rounded 85

Diamond 45

Menu Left Rounded 95

1200V Modero Video Touch Panels

Programming

TPD4 Border Styles by Name (Cont.)
Border styles

Border styles

Menu Left Rounded 105

Menu Top Rounded 65

Menu Left Rounded 115

Menu Top Rounded 75

Menu Left Rounded 125

Menu Top Rounded 85

Menu Left Rounded 135

Menu Top Rounded 95

Menu Left Rounded 145

Menu Top Rounded 105

Menu Left Rounded 155

Menu Top Rounded 115

Menu Left Rounded 165

Menu Top Rounded 125

Menu Left Rounded 175

Menu Top Rounded 135

Menu Left Rounded 185

Menu Top Rounded 145

Menu Left Rounded 195

Menu Top Rounded 155

Menu Right Rounded 15

Menu Top Rounded 165

Menu Right Rounded 25

Menu Top Rounded 175

Menu Right Rounded 35

Menu Top Rounded 185

Menu Right Rounded 45

Menu Top Rounded 195

Menu Right Rounded 55

Neon Active -L

Menu Right Rounded 65

Neon Active -S

Menu Right Rounded 75

Neon Inactive -L

Menu Right Rounded 85

Neon Inactive -S

Menu Right Rounded 95

Oval V 30x60

Menu Right Rounded 105

Oval V 50x100

Menu Right Rounded 115

Oval V 75x150

Menu Right Rounded 125

Oval V 100x200

Menu Right Rounded 135

Oval H 60x30

Menu Right Rounded 145

Oval H 100x50

Menu Right Rounded 155

Oval H 150x75

Menu Right Rounded 165

Oval H 200x100

Menu Right Rounded 175

Picture Frame

Menu Right Rounded 185

Quad Line

Menu Right Rounded 195

Single Line

Menu Rounded Spacer - Vertical

Windows Style Popup

Menu Rounded Spacer - Horizontal

Window Style Popup (Status Bar)

Menu Top Rounded 55

1200V Modero Video Touch Panels

131

Programming

"^" Button Commands
These Button Commands are used in NetLinx Studio and are case insensitive.
All commands that begin with "^" have the capability of assigning a variable text address range and
button state range. A device must first be defined in the NetLinx programming language with values
for the Device: Port : System (in all programming examples - Panel is used in place of these values).
Variable text ranges allow you to target 1 or more variable text channels in a single
command.
Button State ranges allow you to target 1 or more states of a variable text button with a single
command.
"." Character is used for the 'through' notation, also the "&" character is used for the 'And'
notation.
"^" Button Commands
^ANI
Run a button
animation
(in 1/10 second).

Syntax:
"'^ANI-,,,'"
Variable:
variable text address range = 1 - 4000.
start state = Beginning of button state (0= current state).
end state = End of button state.
time = In 1/10 second intervals.
Example:
SEND_COMMAND Panel,"'^ANI-500,1,25,100'"
Runs a button animation at text range 500 from state 1 to state 25 for 10 second.

^APF
Add page flip
action to a button
if it does not
already exist.

Syntax:
"'^APF-,,'"
Variable:
variable text address range = 1 - 4000.
page flip action =

Stan[dardPage] - Flip to standard page
Prev[iousPage] - Flip to previous page
Show[Popup] - Show Popup page
Hide[Popup] - Hide Popup page
Togg[lePopup] - Toggle popup state
ClearG[roup] - Clear popup page group from all pages
ClearP[age] - Clear all popup pages from a page with the
specified page name
ClearA[ll] - Clear all popup pages from all pages

page name = 1 - 50 ASCII characters.
Example:
SEND COMMAND Panel,"'^APF-400,Stan,Main Page'"
Assigns a button to a standard page flip with page name 'Main Page'.

132

1200V Modero Video Touch Panels

Programming

"^" Button Commands (Cont.)
^BAT
Append
non-unicode text.

Syntax:
"'^BAT-,

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2008:10:01 09:21:35Z
Creator Tool                    : FrameMaker 8.0
Modify Date                     : 2008:10:01 09:28:59-05:00
Metadata Date                   : 2008:10:01 09:28:59-05:00
Format                          : application/pdf
Title                           : 0362856.book
Document ID                     : uuid:d617a467-15f4-41f6-9eb4-d681eef60905
Instance ID                     : uuid:57edc258-50bf-4782-a226-9325139fe28a
Page Count                      : 196
Page Layout                     : SinglePage
Creator                         : FrameMaker 8.0

EXIF Metadata provided by EXIF.tools

Amx Modero Nxt 1200V Users Manual 0362856

nxt1200v ab546ff2-53f1-4ca9-a758-ce0c621619f7 AMX Computer Monitor NXT-1200V User Guide |

Navigation menu

Versions of this User Manual:

Views

Navigation