Anbash Technology NC233SW Network Camera User Manual

Shenzhen Anbash Technology Co., Ltd. Network Camera

User Manual

‐1‐Network CameraModel No.: NC233SWView Your World Anywhere……Anytime!Camera Installation on PC and MacThis manual applies to all products.Please read this manual carefully before attempting to install or operate this product.Note: Proceed to the Quick Guide for IOS, Android, PC, Mac
‐2‐1.0 Introduction································································································································· ‐3‐2.0 Installation···································································································································‐5‐2.1Pre‐requisites and Initial Connection························································································· ‐5‐2.2 PC Quickstart·····················································································································‐6‐2.2.1 Camera Setup Software Installation for PC········································································· ‐7‐2.2.2 Finding your Camera with Camera Live Utility····································································· ‐8‐2.2.3 Camera Live Menu Function Introduction···························································································· ‐9‐2.3 Mac Quickstart················································································································· ‐14 ‐2.3.1 Apple Airport Remote Access Setup······················································································‐16 ‐2.4 Camera Homepage············································································································ ‐17 ‐2.5 Live View (using Internet Explorer)························································································· ‐18 ‐2.6 Live View (using Firefox,safari) ‐193.0 Wi‐Fi Wireless ····························································································································‐21 ‐3.1 Wi‐Fi Troubleshooting·········································································································‐24 ‐4.0 Remote Access Setup·····················································································································‐26 ‐4.1 Is the Remote Access Setup already done?················································································‐26 ‐4.2 UPNP SETUP‐‐‐Enabling UPnP for Automatic Remote Access Setup···················································‐27 ‐4.3 Overview of Manual IP address setup (without UPnP)·································································· ‐28 ‐4.3.1 TCP/IP SETUP ‐‐Manual Setup Step 1: Assigning a permanent IP address for your camera on your localnetwork (Without UPnP)····································································································‐29 ‐4.3.2 Manual Setup step 2: Configuring your router to allow access to your camera from the Internet (WithoutUPnP)···························································································································‐31 ‐4.4 DDNS SETUP···················································································································· ‐32 ‐4.4.1 DDNS SETUP Step 1‐‐‐Choosing a Name for your Camera on the Internet···································‐32 ‐4.4.2 DDNS SETUP 2‐‐Automatic Updating of your Camera’s Internet IP address································· ‐33 ‐5.0 Camera Settings··························································································································· ‐35 ‐5.1 Login Password Modification································································································ ‐35 ‐5.2 Quick Setup with the Wizard·································································································‐37 ‐5.3 System Page···················································································································· ‐38 ‐5.4 Reboot··························································································································· ‐39 ‐5.5 Camera Menu·················································································································· ‐39 ‐5.5.1 Camera Setup·········································································································· ‐39 ‐5.5.2 Stream Setup···········································································································‐40 ‐5.5.3 OSD Setup·············································································································· ‐43 ‐5.5.4 Night Vision Setup·····································································································‐44 ‐5.6 Network Menu················································································································· ‐46 ‐5.7 STORAGE························································································································ ‐46 ‐5.7.1 Storage Setup·········································································································· ‐46 ‐5.7.2 MicroSD Card Information and Installation······································································· ‐47 ‐5.7.3 MicroSD card installation·····························································································‐48 ‐5.7.4 NAS STORAGE SETUP ‐‐51 ‐5.7.5 Browse Storage ‐‐ 51‐5.7.6 Format SD Card ‐‐ 52‐5.8 TASK ‐‐ 53‐5.8.1 Motion Detection Using Internet Explorer ‐‐ 53‐5.8.2 Motion Detection using other browsers(Firefox, Chrome, Safari)·············································‐55 ‐5.8.3 Schedule Setup·········································································································‐55 ‐5.8.4 Task Management·····································································································‐56 ‐5.8.4.1 Email Alarm Sending/Email Periodic Sending···································································‐57 ‐5.9 Tools Menu····················································································································· ‐65 ‐
‐3‐5.9.1 System Identity········································································································ ‐66 ‐5.9.2 User Management·····································································································‐66 ‐5.9.3 Date & Time············································································································ ‐67 ‐5.9.4 Backup and Reset······································································································‐68 ‐5.9.5 Automatic Reboot Setup····························································································· ‐69 ‐5.9.6 Firmware Upgrade···································································································· ‐70 ‐5.9.7 Resetting the Camera back to Factory Settings···································································‐72 ‐6.0 TROUBLESHOOTING····················································································································‐79 ‐7.0 Installation Instruction7.1 3G Solar Camera Install7.2 SPY Camera Instal7.3 Outdoor Camera Install7.4 Indoor Camera Install1.0 IntroductionThank you for purchasing the internet video camera.The camera can be accessed remotely, and controlled from any PC/laptop over an Intranet or the Internet via a webbrowser. The user friendly installation procedure and intuitive web‐based interface allows easy integration with yourhome or business network or Wi‐Fi. The camera also comes with motion detection software that can generate alarmtriggers via e‐mail and by uploading images straight to a website. In our experience, we find that our customers getcomfortable with advanced features quickly and then start using the camera on a daily basis to keep in touch with theirhome or loved ones.Using a Mac or PC you can view very high quality live streaming video direct from the camera. It is excellent forapplications such as a baby monitor, nanny cam, pet cam, party cam, security & surveillance, remote observation, elderand patient care as well as limited video conferencing or event broadcasting.An exciting new feature is the ability to turn your iPhone, iPad iOS device and Android OS smartphone, Tabletinto a baby monitor without professional installer, Extra wires, IP address setting, DDNS address setting or routersetting needed, just plug and play. (For detail, Please check the Quick Guide).‐79···································································································································80‐ ‐
‐4‐NoticeThis product may cause interference with other wireless equipment that operate at 2.4GHz ISM band. In the eventof interference please turn off one of the devices or move it to a safe distance.Product AssuranceThis 2.4GHz wireless camera meets wireless frequency security standards and recommended indexes during operation.These standards and indexes are certificated by the academic organization as illustrated in the following paragraphs.Setup of the camera is mostly automatic if you have a current, industry standard router with the “Plug and Play” apps.After you are familiar with the basic functionality of the camera you can enjoy many additional advanced features.For instance, you can enable the automatic sending of motion detection email alerts or automatic uploading of picturesto online servers using the FTP protocol. For instance, you can enable the automatic sending of motion detection emailalerts or automatic uploading of pictures to online servers using the FTP protocol.Another exciting new feature is the ability to turn the camera into a DVR (Digital Video Recorder) by recordingvideo or pictures to a Micro SD memory card. You can also turn the camera into a standalone NVR (Network VideoRecorder) by enabling functionality to save recorded video files to a network server. This could be a commercial serveron the internet or your own standalone NAS (Network attached Storage) hard drive with built‐in FTP server. Thesefeatures do not require a computer. If you wish to use a PC for recording video, we also include free windows softwarefor recording multiple cameras at once.This requires reliable internet service. If you have an older router that is not up to the task, we highly recommendupgrading to one of the current models before you proceed with the camera Live.
‐5‐2.0 Installation2.1Pre-requisites and Initial Connection1. Mini indoor models, Indoor models, Mini bullets outdoor , bullets outdoor , 3G bullets outdoor models, 3G indoormodels, mini spy cameras ,3G spy Camera, DVS.2. Windows PC or Mac OS or Linux computer with internet browserComputer is only required for initial setup, later the camera can work by itself without any computer present atthe camera location3. A local area network with a router / gateway and an available Cat5 wired network jack on your router (not onyour computer)The wired network connection is only needed for initial setup, later the camera can be used wireless with802.11b/g/n. If no Cat5 jack is available, please see Appendix B for alternative setup procedure.You can start using the camera on your own network almost as soon as you plug it in.1.Just connectthe included blue Cat5 cable to the networkjackon the camera and connection the other end to oneof the LAN jacks of your router2. then connect the power supply to the camera and to a wallplug. Ifyour camera has a removable antenna, youmay want to attach it now.IMPORTANT: Make sure camera is plugged into your router/ Airport Extreme/ Time Capsule, not the computer, evenif your computer has an available Cat5 LAN jack.
‐6‐On the box indoor ranges you may want to remove the clear plastic film that is protecting the lens cover. For clearestvideo be careful not to touch the lens.On indoor models the power light will come on within a few seconds. Later you should also see it blinking red occasionally.This means your camera is ready to use. To get started, you need to know the IP address that your router assigned to thecamera. By adding http:// in front of the IP address you get a web link to the camera’s built‐in web server.Until you setup a name for your camera as shown in later sections of this manual, you typically access the camera bytyping the numbers into your browser or by using a bookmark.2.2 PC QuickstartThis Quickstart section applies to the most common configuration for PC users: You have a current generationrouter such as NetGear, LinkSys, or Dlink connected to a standard, non‐routing DSL or cable modem, or you have acombination modem and router which has all functions in one box.Some of our customers have more complicated networks because they have added a wireless router to a wiredrouter, or have business firewalls or VoIP routers in front of the main router. In those situations we recommend thatyou consult an expert to simplify your network by eliminating redundant routers or placing all but one router into bridgemode.With your camera powered up and connected to the router, some PCs will automatically discover the camera andshow a pop up window or icon to let you know that a new device has been found. The popup window shows thecomplete local IP address for the camera. Or, it could be that your camera is automatically discovered by your computerand is shown in the list of attached network devices. On Windows XP this list is called “My network places”.OnVistaand Windows 7 it is just called “Network”However, some PCs and routers do not have the “UPnP” Universal Plug‐and‐Play feature enabled. In following wewill show alternate ways to find the address that your router has assigned to the camera.
‐7‐If you are familiar with your router’s menus you can log in to your router and see the IP address for the IP networkcamera in one of your router’s LAN status screens. By the way, in this document we’re using the words “router” and“gateway” interchangeably.2.2.1 Camera Setup Software Installation for PCFor PC users, we supply a program on the CD called Camera Live for PC with Windows7, Windows 8, XP orVista.This will install utility called Camera Live software on your computer. The Camera Live software searches your localnetwork and displays any cameras it finds. It's very useful if you ever forget the address of you camera or in thiscase. If this is the first time you are running the program you may need to click “Search” several times.Insert provided Software CD into computer’s CD‐ROM drive. If the software installation program does not startautomatically, open CD‐ROM Drive and double click on “Auto Run”.Install “Camera Live” applications on your computer using “Install Software” option.
‐8‐Click Finish to end the installation. You should now find a Camera live icon on your Desktop2.2.2 Finding your Camera with Camera Live UtilityNow you have your camera attached and the software ready, you are ready to find your camera on yournetwork. Double-click the Camera Live icon on your Desktop to launch the Camera Live program.The Camera Live utility should automatically find your camera if it is correctly connected (See image below).Youcan use this program to set up cameras but we recommend that you use this program only to find your IP address. Thendo all setup by going directly to the camera using the IP address, either by double‐clicking on the address or by typingthe number into your browser(with http:// in front)If no camera is found it could be that your Antivirus or Firewall program is blocking the “Camera Live” program. Inthat case you should either disable your Firewall program or use the alternate method of finding the IP address bychecking the menus in your router as described below.
‐9‐Sometimes the program may take a few minutes to find your camera, so if your camera isn’t displayed, wait a fewmoments and then click “Search” to search for cameras again.[Search] – Searches your local network for cameras.[Browser] ‐Select the required camera and click Browser to access the camera via a web browser.[Clean] ‐Click clean to clean up the searched cameras .[Setup] ‐Select the required camera and click Setup to configure the network settings for the camera.Anytime you lose the IP address of your camera, you can run the Setup software to easily find itagain. Once your camera is displayed, either chose “Search” to find the camera.Please note: The camera setup will only detect cameras that are on the same network as your computer. Ensurethe camera is plugged into the same router/network switch that your computer is connected to2.2.3 Camera Live Menu Function IntroductionAfter install this software , doule click on the utility , and sure your camera is connected to your computer or internet .Here are 2 ways for you to searched your connected cameras with it . First , click on to add the camera ,
‐10 ‐If your camera is online ,manually input the UID or click “Discover” , the connected camera’s UID will show as pictureabove ,then Click “OK”You will request to fill the user name and password. Finished these steos ,your camera will be shown .Please payattention to green connect icon on left cornero on picture, “green” means connected , “Red” means you should checkagain the router and camera to make sure all could connect to internet. Choose your camera and double click ,a videoview window will pop up .
‐11 ‐Youwillfindyousavedpicturesandvideohere
‐12 ‐The second way is click the setup icon on top menu , for more details pleare refer to page 8 .Multiview function is added to this software too . If you want to see several cameras on one screen .
‐13 ‐Please Note: To get a best multiview viewing , the Maximum number of camera is 16 . However, there is no limit ofadding camera to this window .
‐14 ‐2.3 Mac QuickstartThis Quickstart section applies to the most common configuration for Mac users: You have an Apple Airport (Extreme orTime Capsule), and your Airport is directly connected to a standard, non‐routing DSL or cable modem.In this section you will be interacting mostly with the Airport Utility. Please note that the Airport Utility by clicking on itsicon in your Mac’s Utilities folder, then make sure it is up to date by going to the menu at the top left of the screen andselect” Check for updates” . Allow any updates to be installed, and then the “About Airport Utility” menu should showat least version 6.3.1 which is current as of July 2013.Now select your Airport by highlighting its picture on the left. Click on “Manual Setup” and enter the Airport password ifneeded, and you should now see the Airport Utility summary screen. Let’s verify a few things:1. The version ofyour Airport firmware should be 7.5.2 or later ifyou have a current generation Airport. UnfortunatelyApple does not provide firmware updates for the earliest Airports. They can be used with TriVision cameras butrequire more detailed setup.2. The “NetworkMode”should be “CreateaWirelessNetwork”, click on the”wireless”icon on top.3. Then select the “ Network” tab on top and the Router mode is set to “DHCP and NAT”. If you have “Bridge Mode(off)” it means you have another router on your network that you may need to eliminate or place into bridgemode before you can have your Airport in “Share a Public IP address” mode. If you have a new generation Airportyou will see a “DHCP reservations” box.
‐15 ‐4. Click on the + (add) button below this box and enter a description for your camera such as “Network camera”, and select“Reserve address by Mac Address”. Enter the MAC address shown on the back of your camera.Be careful about typos. Thereare numbers from 0‐9 and letters in the range of A‐F only. There is no letter O, just number 0 and letter D .Thenselectaipaddress which is in the Airport DHCP range. Make sure that the last group of digits for thisIP address does not end in 1 or 254 since those addresses are usually reserved. Click “Save”, and you should havethe entry in the “DHCP reservations”.Click “Update” to restart.Now the IP camera should always be on your network at the IP address that you reserved, regardless ofwhether you’re using the camera with a wired network connection or wireless after completing the wireless setup.With older generation Airports the IP address reservation feature is missing in the Airport Utility, however the IP cameracan be set up for a fixed local IP address using its own TCP/IP setup menu.Next you will probably want to set up the wireless connection. To prepare your Airport for easiest and most reliableconnection to an IP camera, check the following settings using the Airport Utility.1. If you have set up your network with extra tight security using the “MAC address Access Control” feature inthe Airport Utility, then you will need to add the camera’s MAC address to the allowed list.2. If you have set up your wireless network as “Closed” with a hidden name, it is highly recommended to temporarilyset your network into a normal configuration with a visible network name. Otherwise your camera will not be ableto see your network as one of the available choices to connect to. After setup you can hide your network nameagain. In general, a hidden network name adds more confusion than actual security. There are tools that can revealhidden names easily.
‐16 ‐2.3.1 Apple Airport Remote Access SetupIn order to access the camera remotely from outside your network, you have to tell your Airport to allow access tothe network ports used by the camera.This is called “port setting” and is done with Airport utility as follows:In the Airport Utility version 6.3.1, go to manual setup and select the “Network”icon. 1. Click on the + (add) button below the “port setting”.2. then click on the +(add) icon at the bottom of the box , and enter the following info:Public UDP port: 30000‐30001 (next camera would have 30002‐30003 etc)Public TCP port: 8150 (your 2nd camera would have 8151 here, 3rd 8152etc) Private IP address: (add the IP address for your camera, e.g.10.0.1.201) Private UDP port: 30000‐30001 (same as public UDP port)Private TCP port: 803. Then click on “save” , “Update” and “Continue” to restart your airport.Now some from the outside your network should be able to access your camera using your external IP address with:8150 added to the end. For example, if the Airport summary screen shows your IP address as 192.168.168.120, youwould enter the following in your browser: http://192.168.168.120:8150.
‐17 ‐2.4 Camera HomepageRegardless of the method you used to find your camera’s IP address, Once you have used the Camera Live Software tofind your camera and opened your selected camera or entered the IP address manually into your browser” (with http://in front) , you will be greeted with the Homepage for your camera (which should look something like the belowscreenshot depending on your model):[Enter] Lets you view live video transmitted by the camera.[Setting] This section allows you to setup your camera with its varioussettings. To see video, click on “Enter”,The default setting:Username: adminPassword: admin.This is login is case sensitive, so should be entered exactly as they are above. It is recommended you change yourpassword as soon as you are logged in ‐to avoid unauthorized access to the camera. Make a note of the passwordsomewhere safe, as the only way to reset the password is to reset the cameras, so all settings will be lost.Please note: The password can be any mixture of lower and uppercase alpha‐numeric characters. Extended charactersare not permitted
‐18 ‐2.5 Live View (using Internet Explorer)When using the camera for the first time on a PC with Internet Explorer, your PC will ask you for permission toinstall the viewing software (called ActiveX). This ActiveX is needed to decode the H.264 or MPEG4 video stream andcontrol the camera. Click to “OK” this at the top of your screen, then again click on “OK” on the install menu that willpop up in the middle of your screen.If you have a popup blocker like Google Toolbar you will need to disable it. Within a few seconds you can then see livevideo from the camera.NOTE: If the camera shows video but also displays the message “connecting, waiting…”, close Internet Explorer andwait a couple of minutes for the camera to obtain current time from a internet time server and restart itself.The two links at the top of the screen are Home and Settings.[Home] This takes you back to your Camera Homepage.[Settings] This will take you to the cameras internal settings.Please view the next page for an explanation of the Operating Bar settings.
‐19 ‐1) napshot: Press the Snapshot button tocapture a still image of the camera view,these will automatically be saved to the MyDocuments/ Pictures folder.2) Video Clip: Press the video recordbutton to enable video recording to yourlocal computer. Once finished press thebutton again to stop recording. The videoclip will be saved by default to the Videosdirectory.3) Settings: The Settings button allows youto set the location where the snapshot andthe video clips will be saved.4) S1) Zoom: Click on the “+” button andthe cursor turns to a magnifier. Movethe magnifier to the desired locationand click on an image area.2) Zoom Out: Press the“‐“button to return to the normalview.3) Full screen: Press the button toenable full screen (this functionalityis available on HD 720P and HD 1080Pmodels)1)Mute: Click the Mute button to silencethe audio stream from the camera.1) Volume: Slide the slide blockhorizontally to adjust volume.
‐20 ‐2.6 Live View (using Firefox, Safari)Uponverificationoftheusernameandpassword,thecameraimagewillbegintoload.Adobe Flash Player or QuickTime or your media program may ask you to re‐enter your login username andpassword at this point. This is common on most systems.Please note: You need to have QuickTime Pro Installed on your system to record videos directly from the web browserif you are using a program other than Internet Explorer.The links at the top of the screen are Home, Settings, Secondary Stream and Motion JPEG.[Home] This takes you back to your Camera Homepage.[Settings] will take you to the cameras internal settings.[Secondary Stream] This is set via your settings, and is useful if you need a lower resolution stream for certaindevices (e.g. some mobiles and software)[Motion JPEG] This is a continuous motion JPEG stream – without any audio.
‐21 ‐3.0 Wi-Fi WirelessMost likely your wireless network was set up with a password (also known as wireless key). If you don’t rememberit,youcancheckyourrouter’swirelesssetupmenuor ask the person who set up your wireless network.Without your password you cannot proceed with your camera’s wireless setup, so you can either continue to useyour camera in wired mode or set up a new password in your router. Another possibility is to disable passwords in yourrouter but an unsecured wireless network is not recommended.After installing the camera setup utility on PC and assigned the fixed ip address for your ip camera on Mac, nowyou can start using your camera immediately using the IP address. Just add http:// in front of it and open it in abrowser, such as http://192.168.168.120Clicking on “setting” from the main camera login screen will get you to this:Click on “Network”, then click on “Wireless setup”, and you’ll get to this screen :
‐22 ‐Click the Search button for the camera to scan for available Wi‐Fi networks to connect to. You may see a whole listof networks in your neighborhood. A new screen will display all the wireless networks found.Select the desired network, and click Apply. The camera will automatically choose the best options for connectingto the network. You then need to enter your Wi‐Fi password.If your network is not listed, try “Search” again or repositioning your camera nearer to the wireless device orun‐hide your network name if your router is configured as a closed system.Do NOT manually change any of the settings (SSID, Mode, security mode, Encryption type)
‐23 ‐Please remember that both WPA and WPA2 keys are case sensitive and need to be between 8 and 63 characters.When you have entered the key, click on “Apply”, you’ll get a message about “Wireless setup accepted successfully”,but that only means that the information was stored in the camera. Now you should use the “Test” feature to check ifyou typed it correctly.If the test reports “Success!” you can remove the network cable and it should work wireless after a short delay. Ifthe test reports “no wireless connection”, please double check your WPA key (password” and refer both to the Wi‐Fitroubleshooting and “Known issues” section of this User Guide.Congratulations! At this point you should be able to use your camera wired or wireless on your local network usingthe same local IP address.If it doesn’t connect, we recommend that you temporarily remove wireless security from your router for a quickexperiment to see if the setup succeeds with no passwords. Then put the password back in and try again. Many timesthis will refresh your memory about the exact spelling of your password. Also, it could be either that the camera is toofar from your router, or that your router was set up with the tightest possible security which allows only known devicesto connect to your network. In this case, do not forget to add the MAC address of this camera to your allowed list. Inthis context, MAC refers to a hardware network address and is unrelated to Macintosh computers. The Mac address isprintedonthebackofthecamera.The maximum distance is dependent on the kinds of walls and objects that are between your wireless routerantenna and your camera. One easy test for determining the maximum recommended distance is by using a laptop atthe camera location. If your laptop shows at least 80% (4 or 5 bars) signal strength at that exact same location then thecamera should be ok too. Any less than that may be unreliable, so you may want to move your router or the camera, oradjust the angle of your router’s antennas.Keep in mind that the wireless signal travels easily through common building materials such as wood, glass, sheetrock, and vinyl siding, but does not go at all through metal. If there are any big metal objects such as a fridge, fillingcabinet, or HVAC ducting in between the Wi‐Fi router and the camera, try to reposition either the camera or the routerso that the metal object doesn’t block the signal. Also, many microwave ovens and older 2.4GHz cordless phones mayinterfere with all Wi‐Fi networking while in operation. Using a laptop you may not notice a pause, but with a camera thattransmits or records video continuously any interruption will be much more obvious. Nearby Bluetooth devices such ascell phone headsets, Playstation game controllers, or a wireless keyboard and mouse can also interfere with wirelessnetworks if the devices are too close.The best placement for a wireless router is in an area that is higher up and free of nearby clutter, for example on top of awooden book shelf .
‐24 ‐3.1 Wi-Fi TroubleshootingIf the camera does not connect and you’ve already checked the settings mentioned on the previous page, please log into your router and double check the setting for wireless channel selection. On an Apple airport you would use theAirport Utility.If the “Search” function of the wireless setup page found your Wi‐Fi network it means that the wireless networkinghardware is working. If it then doesn’t connect it means that there is a password or IP address related issue.Please note: The password can be any mixture of lower and uppercase alpha‐numeric characters. Extended charactersare not permitted.Do not use a wireless password with spaces or punctuation in it. For example, “Joe & Mary’s Wi‐Fi#2” may not work unless you change it to something like JoeAndMary2”. Also make sure any WPA/WPA2 password isbetween 8 and 63 characters total.You can temporarily turn off passwords on your Wi‐Fi router, and if you then set “Security mode” to “off” in the camera,it should connect unless you have set your router to reject connection attempts from unknown devices.Assuming that you are now at least connecting without passwords, you can proceed to add wireless security to yourrouter and try again. We recommend WPA2 if available, otherwise WPA. The older WEP mode is obsolete and may notwork correctly on Apple Airport. If you have trouble, switch to WPA2.Since each password type can have 2 variations, this means you could have 4 possible combinations: WPA‐TKIP,WPA‐AES, WPA2‐TKIP, and WPA2‐AES.
‐25 ‐Some routers like Apple Airport series do not show clearly which one of these settings is being used, so if you havedifficulty you should try all 4 possible combinations. On a laptop you typically do not need to specify the exact passwordtype since the laptop will try everything automatically. The camera is picky, it needs to know exactly what type ofpassword you are using and does not try anything other than the exact type that you entered.Remember to “Apply” first, then “Test”.Ifitsays“Connected!” at the end of the test, you can remove the cable.However, as long as the cable is still attached, the camera’s “System” menu will show “No wireless connection”.If you still have trouble, be sure to check the Appendix for known issues.
‐26 ‐4.0 Remote Access Setup4.1 Is the Remote Access Setup already done?If your computer had automatically discovered the camera earlier, this is good news because it means that the “Universal Plugand Play” feature is available on your network and most of the setup may already be done. Your camera would be visible fromthe internet to anyone who knows the exact IP address and usernames and passwords that you choose.Keep in mind that there is a distinction between local (intranet) IP addresses, meaning IP addresses on your ownnetwork, and external (internet) IP addresses, which are unique in the entire world. With the UPnP feature enabled inyour router, the camera’s “System” menu can show you both:1) The link(URL) for accessing the camera from your own network, often something like http://192.168.0.1002) The automatically configured link(URL) for access from a remote location, often something likehttp://192.168.168.120:8150A quick comment about ports: In general, IP addresses can have many different ports associated with them. Whenbrowsing to ordinary web sites there is usually no need to specify a port and that’s why you may have never heardabout ports at all. However, when different devices share a single IP address they are distinguished with a port. Basicallya port has a similar function for an IP address as an extension on a telephone number.Ports are specified by including the port number in the web address with a colon and the number after the .com or .netdomain name. In the example show above the port number is 8150.If UPnP was available on your network, the camera has already set up the correct ports for remote access. A quick wayto see the complete external IP address (URL) is to go to the System menu at the top of the Setting screen. Scrollingdown to the UPnP section you will see the Internet URL (IP address). Then all you need to do is to type either yourinternal (Intranet) or external (Internet) IP address in your browser, depending whether you’re accessing the cameralocally or over the internet. If UPnP worked, you should skip the manual IP address setup and proceed to selecting aname for your camera.Note: if the system menu shows you an internet URL (external IP address) that starts with 192.168 or 10.0, your DSL orCable Modem has a built in router. In this case, contact us with the model number of your modem for assistance.
‐27 ‐4.2 UPNP SETUP---Enabling UPnP for Automatic Remote Access SetupUsually it is very simple to enable UPnP. You just need to log in to your router’s setup screen and find the UPnP menu.Then you click on enable, save the setting and restart both the router and the camera (in that order).The camera comes from the factory with the UPnP enabled. You can double check by selecting the UPnP Setup tabunder the camera’s Network menu:[UPnP] Enable or disable the UPnP function. We recommend you to have UPnP enabled. For most users, the restof the settings can be left as the default settings.[Gateway HTTP/RTSP port forwarding] If this is enabled, the camera will automatically add a port forwarding ruleto your router via UPnP protocol. [External HTTP/RTSP port range] By default, this port range is 8150 – 8350. Theports are assigned in order, so if you only have one camera attached to your system, the chosen port will be8150(8150‐8150) for the first camera, 8151 for the second(8151‐‐‐8151), and so on. Every camera will rememberits port, and it will automatically use this port (if still available) whenever it is powered on.[Gateway RTP port forwarding] Used when viewing the feed through a VLC player. If not wishing to view thefeed through a VLC this should be left enabled.[External RTP port range] The RTP port range can't be changed here ‐you should change it from the TCP/IP setuppage.Click Apply to confirm your setting.If your router UPnP is enabled, the UPnP is still not shown as above, then power off the router and restart both therouter and camera.If UPnP works, clicking on the camera’s “system” menu at the top of the setting screen will show something like thefollowing in the UPnP section:
‐28 ‐4.3 Overview of Manual IP address setup (without UPnP)In the previous section we showed how to tell if your camera was able to automatically configure itself using yourrouter’s UPnP feature. If UPnP worked, please skip ahead to 4.4.1 DDNS SETUP Step 1‐‐‐Choosing a Name for yourCamera on the InternetIn this section we provide an overview of the manual IP address setup procedure. You would only need to do this if UPnPis not available on your network, for example if you have an older router.Most routers come pre‐configured to protect your own network devices from external access. This means that in orderto view your camera remotely over the internet your router needs to be configured to open ports and allow access. Ifthis sounds difficult, you may want to consider upgrading your router to a newer NetGear, LinkSys, or DLink model asthey are very inexpensive now (we’ve seen sales prices under $40). Either way our tech support can help you.The terminology for opening up ports can be different based on the manufacturer of the router. Typically this setting iscalled “Web access”, “DMZ”, “Virtual Server”, “Virtual Service”, “User Defined Service”, “Port Forwarding” or “ PortMapping” . There are 2 main steps involved in port forwarding:1. Reserving a DHCP address or assigning a permanent (static) IP address for your camera on your local network.2. Configuring your router to allow access from the internet to the camera’s IP address on your local network.Strictly speaking, step 1 above is optional, but some routers (especially LinkSys and Belkin models) tend to reassign allthe IP addresses on your home network after a power failure or based on the order in which you use them. Thereforeyour setup is only reliable if you reserve a DHCP address or assign a permanent IP address to your camera and then dothe actual port forwarding.Some residential internet service providers want to charge more for business service and therefore deliberately block allinternet access that looks like it might involve a web server at the standard port 80. That’s why we always recommendusing port 8150, which in our experience is never blocked.
‐29 ‐4.3.1 TCP/IP SETUP --Manual Setup Step 1: Assigning a permanent IP addressfor your camera on your local network (Without UPnP)On your home network (LAN) all your computers, printers and other network connected devices have an IP address. In everyIP address there are 4 groups of digits that can each vary from 1 to 255. For your home network the first 3 numbers arealready determined by your router’s address, which is typically something like 192.168.0.1 or 192.168.1.1 or 10.0.1To pick a permanent address for your camera you first need to know your router’s IP address. It is shown in yourcamera’s“system” menu (at the top of the setting screen) if you scroll down to “Default Gateway”. The router’s IP addressdetermines the first 3 groups of digits for your camera’s IP address.Now we need to select a valid number for the last group of digits. We don’t simply pick a random number because wehave to avoid numbers that are already taken or could be used by your router. The router uses addresses in a range setaside for this purpose (called the DHCP range). For many routers, this DHCP range is from 2 to 100 but you’ll have tocheck your specific router’s DHCP menu. Sometimes this is shown as start and end address, or start address plusnumber of available addresses.Why is this important? We want to select an address outside this range to make sure that your router would never pickthis address for another device.For example, if your router uses the DHCP range from 192.168.0.2 to 100, You could choose 192.168.0.101 as apermanent IP address. Conversely, if your router uses DHCP addresses from 100 to 255, you could use 192.168.0.50 tobe outside the range. Never use addresses that end in .0 or .1, since that is reserved for your router, and never useaddresses that end in a number higher than 255 since that is the highest possible limit.Now that you have picked a local IP address for your camera, then go to the Camera Settings menu, then select“Network” and “TCP/IP Setup” :The camera is setup to obtain an IP address automatically (DHCP) from your Network by default, so these settingsshould not be needed by most users.If your network supports a DHCP server (e.g. router) select this option to have the IP address is assigned automatically. Ifyou select Obtain an IP address automatically you should select Obtain a DNS Server address automatically.
‐30 ‐[Obtain an IP address automatically (DHCP)][Use the following IP address] Select this option when a fixed IP is required.[IP address] Type the IP address of your camera (Required).[Subnet mask] Type the subnet mask (Required).[Default gateway] Type the default gateway (Required).[Primary DNS IP address] Type the IP address of the primary DNS server, if necessary (Optional).[Secondary DNS IP address] Type the IP address of the secondary DNS server, if necessary(Optional). [HTTP port number] The default HTTP port number is 80.[RTSP port range] In order to view video over RTSP the router should be setup to forward a port in the range 30000 to30100 to the camera’s IP address using UDP with an internal port in the range of 30000 to 30100.If you wish to assign the IP address manually, use this page to enter the address detail.1. Click on “use the following IP address”. Then enter the IP address you picked that is outside your router’s DHCPrange.2. Do not change the subnet mask. The default setting of 255.255.255.0 is correct unless you have a very unusual homenetwork.3. Then enter your own router’s address in the “Default Gateway” box. Note that the first 3 groups ofdigits should bethe same as your camera’s IP address. Usually the last digit is 1, sometimes it is 254.Note: It is very important to add the “Default Gateway” when assigning static local IP. While the camera gets thisinformation automatically from the router when using DHCP, the camera will not obtain this information if a localIP address is assigned manually.4. Then click on “Use the following DNS server” and Leave DNS server settings blank or enter both the primary andsecondary DNS addresses that you obtained from your router menu or from your computer’s network connectionmenu.5. HTTP/RTSP PORT: Leave it the default setting. The HTTP port is usually 80.6. RTP port range: Leave it the default setting or enter the RTP port as below: The RTP port range should start at 30000for your first camera. For all additional cameras the start of the range increase by 2, for example your 2nd camerawould have a starting RTP port of 30002, the 3rd camera would have 30004, 4th camera at 30006 etc.After you click on “Apply”, you need to log in to the camera at the address you just picked. Remember to add the http://in front of the IP address, as in http://192.168.168.120.If your port is not 80 you need to add the port too.From now on , regardless of what computers or other devices you have on your own network and regardless of theorder that you turn them on or off, you camera’s IP address will always be the same.On some routers, for example some older models of Leviton or NetGear, you may also need to tell your router about thenetwork camera’s IP address, so that it shows up as a known device on your network.
‐31 ‐4.3.2 Manual Setup step 2: Configuring your router to allow access to yourcamera from the Internet (Without UPnP)If you are not using UPNP or UPNP is disabled on your router, you will need to open a port on your router sothat you can access your camera from the internet.If you are unsure if UPNP is working on your camera, visit your camera Settings System page. Under UPNPport forwarding it will be labeled as “Success”, “Failed” or “Disabled”.Port forwarding is sometimes called “Virtual Server”, “user defined service”, or “port mapping” and is explained in yourrouter’s manual or online help. The manual is usually available from the manufacturer’s tech support web site.Firewall security features built into some routers may prevent the camera’s UPNP from configuring your router.Your router connects to the Internet over a series of “ports” and sometimes the default ports used by thecamera are blocked from access over the Internet, therefore, these ports need to be made accessible. This isachieved using the Port Forwarding function on your router. The ports used by the camera must be openedthrough the router for remote access to your camera. Check the following website:http://www.portforward.com/You typically need to enter the external (public) and internal (Private) ports(hosts) and select TCP.For browser access to the camera you need to forward public port 8150 to internal port (base port) 80. Your 1stcamera would use TCP port 8150 to internal port (base port) 80 , Your 2nd camera would use TCP port 8151 to internalport (base port) 80 AND the 3rd camera would use TCP port 8152 to internal port (base port) 80.After these settings, your router typically needs to be restarted and then you’re ready to use the camera over theinternet. First you need your router’s IP address on the internet (that’s NOT the local address that starts with 192.168).You can find this address by looking at your router’s WAN menu.A friend who is outside your local network should then be able to access your camera using this IP address and port8150, as in http://192.168.168.120:8150
‐32 ‐4.4 DDNS SETUP4.4.1 DDNS SETUP Step 1---Choosing a Name for your Camera on the InternetWith typical residential internet service your router’s IP address can change from time to time. Looking up the current IPaddress can be inconvenient, and buying a static IP address is an unnecessary monthly expense. www.dtdns.com andwww.dyndns.com are the recommended companies for “Dynamic DNS” service. Also known as DDNS, this is a totallyfree service that allows your own name to be assigned to your camera. This name takes the place of the IP address.Together with software in your camera this also makes sure the name for your camera is always updated with thecorrect IP address.First you create a free account with one or both of these companies. We’ll take www.dtdns.com as an example. The“createaccount”functionisbesideLoginbelow.Donotregisteradomainorsignupforanyotherpaidservices.Youjustneed the free account.Once you have an account and once you validated it by responding to their email, log in and select” Hosts/ Redirects” onthe top left of the screen, then “Add Host”. For Hostname, pick anything you like as a name for your camera, except donot use spaces. Use only lower case letters and numbers. Then click on the domain names you can pick from, as well assome that they consider premium names worth paying for. For example, you could pick servehttp.com as your democameras.Then be sure that only “DNS Host (A)” is selected. Don’t worry about the current IP address and don’t change anythingelse. Click on “Create Host” and you’re done! Please write down your complete hostname as well as the username andpassword you used for logging in to No‐IP.com as you’ll need it for the next step.DynDNS.com is very similar but in their case there is an additional step of checking out a shopping cart with a zero dollar
‐33 ‐fee.Now proceed to the next section to make sure your name is updated correctly.4.4.2 DDNS SETUP 2--Automatic Updating of your Camera’s Internet IPaddressIn the previous step we set up a name for your camera. To make sure that this hostname always corresponds to thecorrect IP address for your camera we have to make sure it is updated automatically when there is a change.Dynamic DNS (DDNS) is simply a way of using a static hostname to connect to a dynamic IP address. Whenconnected to your ISP, you are assigned a temporary IP address. DDNS services keep track of your IP address androute your Domain name to that address when you wish to connect to the camera from a remote location.There is no need for client software. Our IP cameras have a DDNS menu that allows you to enter your hostnameinformation. This DDNS menu is under “Network” in the camera’s “Settings”. Be sure to select the DDNS provider, forinstance if you signed up with No‐IP.com you should select No‐IP in the camera’s DDNS menu.[DDNS] Enable or disable DDNS connection. Click “Enable” for the rest of the options to appear.[Service Provider] Select a provider from the drop down list then click “Register”. This will take you to theservice provider’s website where you can register your own personal host name. Please follow the instructionson the provider’s site, and then return to this page to enter the details.[Host Name] Enter the host name you have registered (e.g. yourname.dtdns.net).[User Name] Enter the user name for the account you registered with the serviceprovider.[Password] Enter the password for the account you registered with the service provider.[Re‐type password] Re‐confirm the password.Now you have setup an easily accessible external address for your camera, you now need to setup and confirm anexternal port for your camera. This is covered in the UPnP section.Please note: if you have only just registered your DDNS account, it may take a while your account is activatedand full registered on the internet. Some of the DDNS service listed offer free paying service. A free account ismore than adequate for a camera to use.After you enter your account and hostname information and UPNP is enabled, you can go to the camera’s “System”menu at the top of the Settings screen and scroll down to the DDNS section. If it worked, the camera’s external addresswill be listed under “Internet URL”.
‐34 ‐If it says “Updating” or Unavailable” you should double check your account settings. No‐IP.com uses your completeemail address as user name, and the password required in this menu is the one you created during No‐IP account setup.If successful the camera will show you the complete external URL for your reference.The external address using DDNS is made up of two parts – your DDNS account address and the port youopened via UPnP or manually.For example: DDNS Host name account: http://yourname.dtdns.com Port: 8150So with the above information, your camera would have the address of: http://yourname.dtdns.com:8150Open any internet browser on your computer, and type your own DDNS account name,followedby:8150 (that’sa colon, followed by 8150). After a few moments, your Camera Homepage should be displayed. You can then loginto view your camera or change your settings as normal.To confirm your own external camera address, stay within the Settings menu, and click on “System” at the topright of the screen. This will list various settings of your camera. Under UPNP Port Forwarding, it should list yourcameras hostname and port.Note: Only 1 single camera per network needs the DDNS setup. This enables access to the entire network.Important Notes1) If you try to access your own camera(s) from your home using the external IP address it may not work. Someinternet service providers recognize that you are trying to do something that usually doesn’t make sense. Theirrouters may block requests that go from your network out to the internet and then loop back to your ownnetwork.Therefore we always recommend that you get in touch with a friend to help you test the remote access to yourcamera from outside your own network. Or you can use an iPhone in 3G mode (Wi‐Fi turned off)2) Once your camera is live on the internet, you should changetheadminpasswordtosomethingonlyyouwouldknow.See the “User management” menu under “Tools” section of your camera’s “Settings” screen. Only admin canchange settings. If you add other user names they can only see video without changing anything.If you forget your password you can always reset your camera to factory settings using the reset procedure shown at theend of this manual.
‐35 ‐5.0 Camera Settings5.1 Login Password ModificationYou can now view your camera live, but this is only on your local network, so you can now refine and customizethe settings of the camera. To continue with camera customization, access your camera’s Settings page by clickingon the “Settings” word from your Live View, or click on the word “Settings” from the Camera Homepage.Please note: If you are installing the camera for the first time or after a reset to factory defaults, you are advisedto change the cameras default password as per the message displayed.Changing the cameras default password ishighly recommended to stop unauthorized access to your camera.Click the link displayed to access the Administrator Password editing page.The Administrator username is always “admin” in lowercase. Choose a password that is memorable only to you –avoid passwords that are easy to guess, such as “password” “admin” “123456” or your personal details.Please note: Keep this password safe. The only way to recover from a lost password isto reset the camera back to its default settings, and this will wipe all other settingsOnce you have typed your password twice, click Save. The system will then ask you to login again. You should thensee the following screen:
‐36 ‐
‐37 ‐5.2 Quick Setup with the WizardTo make the setup process slightly quicker for users, we have created a Setup Wizard which takes youthrough common options to getting your camera setup wirelessly and with your custom settings.Within the Settings screen, click on “Wizard” in the Header Menu.The Wizard will launch in a new window. Follow the simple instructions on the screen and enter the requireddetails, clicking next to proceed through each step.With this Wizard, you will be able to set the:Name of CameraQuality of Picture you wish to viewTime ZoneSystem TimeWi‐Fi SetupTCP/IP SetupThis should help you get your camera setup and working very quickly at a basic level.
‐38 ‐5.3 System PageFrom within the Settings menu, clicking on “System” at the top right will list the system information of yourcamera. This screen is one of the most useful in the camera Settings. This screen lists information you may need ifyou want connect to your camera from other systems. It’s a great way to check if your camera has all the detailsneeded to operate correctly.Firmware Version – Your current firmware version. Check the .com website or contact our technical support:support@ .com to see if there are updates for your modelWireless – The current status and strength of your wireless connection if in use.IP address – The internal IP address of your camera so you can access it on your local network.DNS Servers – If this option is empty, it may prevent your camera from sending email alerts. Enter the DNS inthe TCP/IP menu if needed.DDNS – If you do not have a static IP address, a DDNS service helps you access your camera easily fromoutside your network. This confirms the DDNS is active or not.UPNP – If your router has UPNP and it has successfully worked with your camera, this will tell you here. Thissaves you forwarding any ports.Internet URL – This is the external address and Port of the camera.P2P‐This is the fast and simple remote access solution on PC, Mac, IOS, Android, please check the Quick Guidefor the detail of installation.Storage – Lets you know if storage is available on SD card or NAS drive.
‐39 ‐5.4 RebootClick Reboot in the Header Menu to access the Camera Reboot page to restart the camera. Rebooting thecamera will retain all the settings and configurations.A reboot is normally necessary when you insert a microSD card into the camera.5.5 Camera Menu5.5.1 Camera SetupThe Camera menu is located on the right of the Settings screen. When you click on the word “Camera”, a sub‐menuof camera setup options will be displayed.For most users, many of these settings can be left as default.Camera Setting OptionsSystem:[Enable privacy mode] Videos will not be seen.[Power LED light] Turns off the camera front LED on or offCamera:[Light Frequency] Two options: 50Hz & 60Hz. This should be set according to the mains frequency of the countrythe camera is being used in. For EU this would be 50Hz. For the USA this would be 60Hz.[Enable image mirror] Display a mirrored view of the video.[Enable image flip vertical] Display video upside down – useful if you have installed the camera upside down.Microphone:[Microphone] Enables or disables the built‐in microphone.[Volume] Adjusts the sensitivity of the microphone from 0~10 where 0 is the lowest.
‐40 ‐Click Apply to confirm your setting.5.5.2 Stream SetupClick on Stream Setup under the Camera Menu to change the streaming settings for your camera. This is useful ifyou require a certain size of video stream, a certain quality, or different streams for different devices (such aslaptop or mobile phone).Default settings will normally suffice for most users.There are a number of video streams available. You can configure settings for the primary and an optionalsecondary video stream. Configuring a secondary stream is useful for providing a video stream that is at a lowerresolution than the primary stream to third‐party devices or software. Some devices and software require lowerresolution.The Mobile stream is similar to the first two streams but is purely for mobile viewing and has a fixed resolution.
‐41 ‐Stream Setting Options[Present] There are five pre‐programmed stream profiles for quick set‐up. Please choose the one according toyour bandwidth.[Image size] Image resolutions available are as follows:480P Model: 640 x 480(VGA), 320 x 240(QVGA), 160 x 120 (QQVGA). The mobile stream has a fixed image sizeof 176x144.HD 720 Model: 1280x720 (HD720p), 768x432, 512x288, 256x144). The mobile stream has a fixed image sizeof 176x144.HD 1080 Model: 1920x1080 (HD1080p), 1280x720 (HD720p), 768x432, 512x288, 256x144. The mobile stream hasa fixed image size of 176x144.[Frame rate] Twelve options: 1/2/3/4/5/6/8/10/15/20/25/30 frames per second (fps). The frame rate isautomatically determined by the camera and this depends on the network bandwidth available at the time.This frame rate setting imposes the maximum frame rate that the camera will transmit.[H.264/MPEG4 bit rate] Select H.264/MPEG4 bit rate. These settings determine the image quality, however higherbitrates require greater bandwidth. Please select the appropriate settings according to your connection speedand network traffic. If you are experiencing jerky video it may be necessary to decrease the bitrate.[MJPEG Quality] This sets the quality of the video when viewing the camera using Motion JPEG (without audio).Itcanbefrom20to100where100isthebestquality.[JPEG snapshot Quality] The quality of the snapshot saved using Live View page (Internet Explorer only). It alsoaffects the quality of the snapshot to be uploaded to an FTP Server. It can be from 20 to 100 where 100 is thebest quality.[Audio] Select or disable the audio bit rate.[Authentication] Select or disable MPEG4 RTSP authentication.Clicking on the name of the stream will display various paths to the paths to the particularvideo stream
‐42 ‐5.5.3 Image Setup[Brightness] make the image brighter or darker by a specified amount. When increasing brightness, you may findthat you lose some contrast on the brightest details in the image while the rest of the image has the samecontrast as before.[Contrast] Contrast is defined as the separation between the darkest and brightest areas of the image. Increasecontrast and you increase the separation between dark and bright, making shadows darker and highlightsbrighter. Decrease contrast and you bring the shadows up and the highlights down to make them closer to oneanother. Adding contrast usually adds "pop" and makes an image look more vibrant while decreasing contrast canmake an image look duller.[Hue] Change is similar to rotating a color wheel to select a different mixture of colors[Saturation] Saturation is similar to contrast, however instead of increasing the separation between shadowsand highlights, we increase the separation between colors.[Sharpness] Sharpness can be defined as edge contrast, that is, the contrast along edges in a photo. When weincrease sharpness, we increase the contrast only along/near edges in the photo while leaving smooth areas ofthe image alone.[Auto Exposure Target] Automatic exposure (abbreviation: AE) mode automatically calculates and adjustsexposure settings to match (as closely as possible) the subject's mid‐tone to the mid‐tone of the photograph.Exposure is a combination of the length of time and the illuminance at the photosensitive material. Exposure timeis controlled in a camera by shutter speed and the illuminance by the lens aperture and the scene luminance.Slower shutter speeds (exposing the medium for a longer period of time), and greater lens apertures (admittingmore light), and higher‐luminance scenes produce greater exposures.
‐43 ‐5.5.4 OSD SetupClick on OSD Setup under the Camera Menu to change the on‐screen display parameters of the camera.On Screen Display Setting Options[OSD] Enable or Disable the On Screen Display.OSD Options[Display date and time] Set the OSD to display the Date and Time of the camera. Please note that this function willsimply display the date and time that has been programmed in the camera and therefore the time and date maybe incorrect unless the camera is synchronized to a time and date server on the internet. This is accessible underthe Tools menu and will be covered in more detail in the manual.[Display system name] Set the OSD to display the System Name of the camera. The system name can be modified fromthe System Identity page, accessible under the Tools menu, and will be covered in more detail in the manual.[Display the text below] Set the OSD to display specific text. Use the text field to input the desired text.Click Apply to confirm your setting.
‐44 ‐5.5.5 Night Vision SettingsAt night, with the infra‐red lights, the cameras simply show reflected light. If the camera is pointed at empty space (notpointed at trees, grass, or other objects), the night time picture will be entirely black. The infra‐red lights seem toproject out roughly 50 feet ‐of course at that distance at night it will be difficult to pick out many details about theobject that is recorded.If there is ambient lighting (street lights, overhead security light, infra‐red light provided by other cameras or external IRemitter) it is possible to extend the night time visible area.1.The” Infrared LED control‐‐“Auto” switches on the IR LEDs automatically when there isn’t enough light to produce agood quality image. “On” turns the IR LEDs on permanently and ignores the light level in the room (resulting in a Black &White mode). When “Off” is selected the IR LEDs are kept in the off state even if the light level of the room is too dark toproduce a good quality image. This may be useful if the LEDs are reflecting off a nearby surface and obstructing yourview.Please note: “Auto” uses the light sensor on the front of the camera to check ambient light level to turn on the IRLEDs at night. The sensor is below the lens.2.“Black & White Mode”‐‐ “Auto” switches the video from color to monochrome when the IR LEDs are turned on. “On”switches the video to monochrome irrelevant of the status of the IR LEDs. “Off” forces the camera to stay in color modeeven when the IR LEDs are on. The default setting is “Auto” so that you have the highest sensitivity at night. In manyenvironments you have better picture quality as well as color night vision with ambient light if you set this setting to“Off”, so you may want to try it.3.“Moonlight mode”‐‐ Turns Moonlight mode on or off or set it to automatic. The Moonlight feature superimposesframes in order to brighten the image being viewed. This is also known as frame integration. In “Auto” the camera usesthe front Light Level Sensor to detect the amount of light available to the camera. Should the light level below, thecamera would automatically turn this feature on. Moonlight mode boosts the available light by reducing the frame rateto 7.5 fps. When “Moonlight model” is “auto” or “On”, the cameras produce gorgeous night vision, especially theoutdoor serials.
‐45 ‐With LED and Moonlight mode “OFF” With LED and Moonlight mode ON or AutoPlease note: If you are using the cameras to look through a window, you should set the night vision mode to turn offthe IR LEDs instead turn on the automatic moonlight mode. Otherwise the IR LEDs would reflect off the window glassand the glare would make everything almost invisible.4. “IR Cut Filter control”‐‐ IR is present naturally in day light, this can cause discolouration of images where the greenscan look purplish. The IR cut filter blocks these IR lights from coming back onto the lens of camera, and this gives atrue day image. However, if the IR cut filter is on during night, the night vision will not work.It is recommended to leave the IR cut filter control to Auto at all times, to achieve best results from the camera.During the day, an optical “IR Cut filter” removes all IR light. This makes the camera’s vision similar to a human eyewhich does not see IR light, and therefore all colors appear vivid and natural to us. At night, the filter moves out ofthe optical path to enable IR night vision. You can actually hear a muted click when this filter moves in or out. Thishappens both during power‐up and when light levels change between day & night.
‐46 ‐5.6 Network MenuThe Network menu is located on the right of the Settings screen. When you click on the word “Network”, asub‐menu of network setup options will be displayed.Skip the wireless setup chapter, please check page 18 to21. Skip the TCP/IP setup chapter, please check page 25 to26. Skip the DDNS setup chapter, please check page 28 to30. Skip the UPnP setup chapter, please check page 23.Skip the P2P setup chapter, please check QuickGuide.5.7 STORAGE5.7.1 Storage SetupWhen the camera powers up with a Micro SD present in the slot, Enable “storage” andselect store to “SD card”, and then select “format the Micro SD”.The Storage menu is located on the right of the Settings screen. When you click on the words “Storage”, asub‐menu of options will be displayedThe camera can record video direct to virtually an NAS drive or to its internal microSD memory card.[Storage] Select Enable to enable storage option.[Storage Select] Select whether you want to record on NAS or microSDcard. [Store directory] This is the folder that videos will be saved to.[Max Space] Storage capacity the camera will use on the chosen storage.[Max files] The maximum number of files for all the videos can be recorded beforeoverwriting. Click Apply to confirm your setting.
‐47 ‐5.7.2 MicroSD Card Information and InstallationAdding a Micro SD to your camera will allow you to record footage and motion alerts direct to memory cardfor future review.Please note: It is advised to insert the microSD card before any other setup begins as the card will not berecognized if inserted once the camera is turned on. Every time the card is re‐inserted, you will need to turn thepower off and then on again for the card to be recognized.If you do not have a microSD card, but plan to add one later, this is fine. When inserting the card, rememberto turn the power off from the camera, insert the card, and then power it back on.The camera officially supports microSD memory cards with capacities up to 128GB, including those labelled“SDHC”.It is required to install the SD card into the camera and format it within the camera. This option can be foundunder the Storage menu.MicroSD Important Notes and Information1. There is a limit to the number of rewrites possible on any MicroSD memory card. If you notice the cardbecoming slow or sluggish after a reasonable usage, you will probably need to replace the microSD memory card.You should try to avoid purchasing second‐hand memory cards.2. If the card is not recognized by the camera, try formatting the microSD card via your computer and then tryingit again in the camera.3. Images may not be recorded or read correctly if an unsupported MicroSD memory card is used with the camera.4. Carefully read the User guide, precautions on use, and any other information that was supplied with thememory card when purchased.5. Do not use a memory card containing data recorded by another device as this may result in the cameranot functioning correctly.6. Do not modify, overwrite the data, or change the folder names of the MicroSD memory card. It may result inthe camera not functioning correctly.7. Always turn the power off to your camera before removing the microSD memory card.8. Tech. cannot be held liable for any loss of data or product misuse.
‐48 ‐5.7.3 MicroSD card installationThe MicroSD card is not included in packages. The slot for the Micro SD card is at the right side of the indoor camerasand behind the lens cover on outdoor cameras. (See diagram below). The card can only be inserted into the camerawith the golden pins of the microSD card facing the front of the camera. The SD card should not be forced into theSD card slot as this may damage the camera.Errors can only be fixed by reformatting the Micro SD on your PC using the formatting toolfrom http://www.sdcard.org/consumers/formatter.A reboot is normally necessary when you insert a microSD card into the camera and after formatting the microSDcard with the camera’s format tool.
‐49 ‐
‐50 ‐To access the Micro SD card slot on the outdoor camera, please bring the camera indoor (in an area of low humidity),then unscrew the entire front part of the camera. It is easiest to do it if you take the sunshield off first. The Micro SD cardslot is right under the reset button show belowPlease be very careful not to touch the lens. The Micro SD slides into the slot and there is a positive “click” when it islocked in place. If it doesn’t want to go in effortless it is probably upside down.When done, please be careful when screwing the front part back on to make sure the threads are engaging nicely. Do notuse any tools, hand tight is good enough.
‐51 ‐5.7.4 NAS STORAGE SETUP[NAS remote path] This is the address & path where to save the files on NAS Drive (up to a maximum of 2directory levels).[Authorization1] Select whether authentication is required by the NAS Drive.[User name] & [Password] Type the user name and password of the NAS Drive. This field is required if yourNAS Drive requires authentication.Click Apply to confirm your setting.Please note : After the setting on “Storage“ and Micro‐SD card or NAS status is ready. You can go to next chapter“Task”, and configure motion detection to initiate the snapshots or video recording to Micro SD card or NAS.5.7.5 Browse StorageClicking on Browse Storage will take you to the following screen where you can view or download the contents ofthe storage drive.The resulting video files can be viewed with the free QuickTime for Windows or Mac. You do not need QuickTime X or Prounless you want to compress the resulting video to iPhone/iPod format. Shorter video clips will download much faster. Ifyou have many video files you could also remove the Micro SD card and access it directly from your computer (withsuitable adapter if needed). This is only practical for indoor cameras due to easy accessibility of the Micro SD card slot atthe bottom.
‐52 ‐[All] Enables you to view and delete all the files recorded.[Snapshot on Alarm] Enables you to view and delete snapshots which were recorded upon motion detection[Snapshot at Interval] Enables you to view and delete all the snapshots which were recorded on periodicalbasis[Record on Alarm] Enable you to view and delete all the videos which were recorded upon motion detection[Continuous Record] Enables you to view and delete all the videos recorded according to the continuous recordschedule.Thebrowsestoragepageshowsasummaryofallthefilessavedforaspecificfunction.Toaccessthefilespleaseclick on the relevant link and this will display all the files.5.7.6 Format SD CardTo format SD card, all files will be lost after format.
‐53 ‐Login to the camera, under Settings>Storage>Format SD cardNote: Before the SD card is formatted the Format SD card page will display status as "Not Ready". The SD cardformat can take a few minutes depending on the size of the SD card.A reboot is normally necessary when you insert a microSD card into the camera and after formatting the microSD cardwith the camera’s format tool.5.8 TASK5.8.1 Motion Detection Using Internet ExplorerMotion Detection can trigger an alarm that sends images via e‐mail or FTP (File Transfer Protocol). You can set upto four different Motion Detection windows.
‐54 ‐The camera refers to motion detection as an “alarm”. You can select what you want the camera to do once the motion isdetected. In general, motion detection works by comparing the current video frame with the averages of the previousvideo frames. Any difference is considered to be motion, and the sensitivity adjustment can be used to make the cameramore aware or less aware of small amounts of motion.Moving an object (a person or a car, for instance) directly toward the camera may not trigger motion detection until theobject is within 10 to 15 feet of the camera. Motion detection seems to work well when the object is moving from one sideof the picture to the other side, often triggering in a second or less.The factory default setting for motion detection is a single motion detection window covering the entire visible area. The“Motion Detection” menu allows you to designate up to 4 separate windows with individually adjustable sensitivity. Afterselecting “Motion detection” from the main settings screen, you may need to expand the size of the display windowtowards the right to see the 4 controls for individual motion detection windows. Each window can have individuallyadjustable sensitivity and threshold.Please note that this “Motion Detection” menu is entirely optional and is generally not used unless you have very specificrequirements to treat motion on some parts of the screen different from other parts.[Window] Check this box to enable the window.[Threshold] Determines at what point the alarm is triggered. A lower threshold means less motion is needed totrigger the alarm. A higher threshold means more motion is needed to trigger the alarm. Threshold is indicated bythe blue bar when motion is detected.[Sensitivity] Determines how easily the camera detects motion. Lower sensitivity means the camera is less likely todetect motion. Higher sensitivity means the camera is more likely to detect motion.Note: Sliding the Sensitivity bar to the left will decrease the sensitivity of the motion detection i.e. ‘More’movement is required to trigger the alarm.Internet Explorer can show you a live indicator for motion: When there is motion, a blue level appears between thesensitivity and threshold slider as shown in the picture. More blue means more motion. To trigger an alarm (andhence send out emails or upload to an FTP server etc) the detected amount of motion needs to be larger than thethreshold setting. If the blue level does not reach the threshold setting the motion is ignored.The best way to configure these settings is to adjust the settings and have someone walk in front of the camerauntil your feel you are getting the required results. This trial and error method make take quite long to get rightbut it’s the best way to obtain good results.Please note: Motion detection in Internet Explorer uses the ActiveX plug‐in. You will needto install or enable this plug‐in if you do not have it. To check you have ActiveX enabled
‐55 ‐visit http://www.pcpitstop.com/testax.aspTo reduce the chance of false alarms you would increase the threshold (move threshold slider to right) or decreasesensitivity (move sensitivity slider to left) .5.8.2 Motion Detection using other browsers(Firefox, Chrome, Safari)[Window] Check this box to enable the window.[Threshold] Determines at what point the alarm is triggered. A lower threshold means less motion is needed totrigger the alarm. A higher threshold means more motion is needed to trigger the alarm. Threshold is indicated bythe blue bar when motion is detected.[Sensitivity] Determines how easily the camera detects motion. Lower sensitivity means the camera is less likely todetect motion. Higher sensitivity means the camera is more likely to detect motion.To reduce the chance of false alarms you would increase the threshold (move threshold slider to right) or decreasesensitivity (move sensitivity slider to left) .Please note: Motion detection in other browsers uses the Adobe Flash plug‐in. You willneed to install the Flash plug‐in if you do not have it. To check you have the latest versionof Flash, visit http://updateflash.org5.8.3 Schedule SetupThe alarm that the motion detection triggers can be set to be active or inactive at certain times of the week.
‐56 ‐By default, the schedule is set to be “active” at all times “always”.However you can set the schedule not to trigger alarms at certain times (useful for instance if you don’t want alarmsto go off while your office is open from 9am until 5.30pm). You can set up to 4 schedules, and you can use these tosend alarms to different places – such as emails, FTP or SD card.Schedule Setup Options[Schedule ID] Select the ID, you can save up to 4 schedules and use them for different purposes.[No.] Setup the specified times in every Schedule ID, you can save up to 8 specified times and use them fordifferent purposes.[Enable] Activates the alarm on specified times. Ticking this box to activate the alarm on the specified times.[Start time] Start time of the alarm.[End time] End time of the alarm.[Days] Ticking this box activate the alarm daily on the specified times from Monday to Sunday.Click Apply to confirm your setting5.8.4 Task ManagementThere are various tasks you can enable on your camera. This section will explain the various tasks and theirfunctions
‐57 ‐[Enable] Enable task.[Schedule] Option to choose always or set a particular schedule. Check Schedule setup to select the right scheduleID for your task.[Task] Task function. Click on the task to login the task setting screen below.Click Apply to confirm your setting5.8.4.1 Email Alarm Sending/Email Periodic SendingFor automatic emailing you will need both an outgoing email server and one or more email receiving addresses. If youdon’t have this information handy you may want to refer to your internet service provider’s help pages or your MicrosoftOutlook or other email program account settings.Following is an example of a proper configuration for using Gmail as the outbound server, which then can send email toany receiving email address.
‐58 ‐Note: Gmail requires that you go to your account settings on Gmail.com and enable the POP feature (PostOffice Protocol). If your Gmail account does not have POP enabled, the camera will not be able to send email.[Enable] Enable task.[Schedule] Option to choose always or set a particular schedule. Check Schedule setup to select the right scheduleID for your task.[Task] Task function. Click on the task to login the task setting screen below.Click Apply to confirm your setting1. Snapshot from‐‐‐ Select snapshot stream source which can be “Primary stream” , “Secondary stream” and “ MobileStream” . For smaller pictures you can select from “Secondary stream”.
‐59 ‐2. Snapshot Duration‐‐ The number of seconds that the camera should keep sending emails with attached imageafter motion stops.3. Snapshot Frame Rate‐‐ The number of frames per seconds that the camera should keep sending images at when analarm is triggered. If “Snapshot duration” had a value of 4 and “snapshot frame rate” had a value of 2, you would begetting 2 images each second for 4 seconds in a row, meaning 8 pictures total for each motion detection event.4. Alarm Interval‐‐ This is the number of seconds for which the camera should stop sending e‐mail alerts after thefirst set. Setting the time to 0 disables this feature. It allows you to designate a time (in seconds) during which newemails are suppressed. For example, if you want to avoid a flood of emails, you could set this time to 3600 seconds sothat after a motion detection event you wouldn’t get any new emails for at least 1 hour.5. SMTP server name‐‐Type the name or IP address of the SMTP server you want to use for sending the e‐Mails.Please note that some networks do not allow e‐mail relaying. Check with your system administrator or Internetservice provider for more details.6. SMTP server port‐‐ The port number of the e‐mail server (default is 25)7. Secure SSL connection‐‐Select whether your SMPT server requires an SSL connection.8. Authentication‐‐Select whether authentication is required by the SMTP server.9. User name] & Password‐‐Type the user name and password of the e‐mail account you wish to use. This field isrequired if your SMTP server requires authentication.10. Re‐type password‐‐ Re‐type the password.11. Sender e‐mail address‐‐Type the e‐mail address of the account you are using to send the e‐mail. This will bethe address the emails come from.12. Receiver e‐mail address‐‐Type the recipients’ e‐mail addresses for who you want the emails to be sent to. Upto 3 addresses can be entered.13. Subject‐‐Subject of the e‐mail that is sent. Entering a relevant subject will help identify the alarm better. i.e.“Garage Alarm”14. Message‐‐Type the text you wish to appear in the e‐mail. E.g. this is to notify you that your alarm has beentriggered.Notes: Email settings can be obtained from your e‐mail service provider. An SMTP email account is required – theseare very common if you use POP3 email and some IMAP servers. A true IMAP server will not work.Some ISPs won’t let you use any other SMTP server other than their own (British Telecom BT is a good example ofthis).15. Click Apply to confirm your setting.16. Note that ifyou have a typo in any ofthis information, the camera would have no way to let you know about that.You just won’t get emails. To summarize, Gmail requires:SMTP server name: smtp.gmail.comPort: 465Authentication: YesSecure SSL connection: YesUsername must include:@gmail.comOther mail servers have their own unique settings and requirements. Some web mail services such as Yahoo cantypically not be used for sending unless you subscribe to optional paid subscriptions like Yahoo PLUS.Receiver mail address: Any email account can be used as a receiving email address, including the same as sendingemail. You can also send email to several receiving email addresses, up to 3 total.17. NOTE: It is easy to have a typo. The SMTP server name never has an@symbol. On the other hand, email addressesmust have an @ symbol.5.8.4.2 Email Periodic SendingInstead of using motion detection in Email Alarm Sending, you can also use the “Email Periodic sending” menu to uploadpictures at regular time intervals.“Email Periodic Sending” menu is very similar to setting up the “Email Alarm Sending”, so it’s not explained here.
‐60 ‐Period Interval‐‐ Time interval between snapshots. It allows you to designate a time (in seconds or minutes or hours) duringwhich new emails are suppressed. For example, if you want to avoid a flood of emails, you could set this time to60 minutes so that you wouldn’t get any new emails for 1 hour.Some email server settings to use your camerawith popular email providers: gmail.com gmx.comSMTP server name: smtp.gmail.com SMTP server name: smtp.gmx.comSMTP server port: 465 SMTP server port: 587Secure SSL: Yes Secure SSL: NoAuthentication: Yes Authentication: YesUsername: YourUserName@gmail.com Username: YourUserName@gmx.netPassword: xxxxxxx Password: xxxxxxxatt.net comcast.netSMTP server name: smtp.att.yahoo.com SMTP server name: smtp.comcast.comSMTP server port: 25 SMTP server port: 587Secure SSL: No Secure SSL: NoAuthentication: Yes Authentication: YesUsername: YourUserName@att.net Username: YourUserName@comcast.netPassword: xxxxxxx Password: xxxxxxxPlease note: The most common reason for Email Alerts not being sent is that the cameras Primary DNS IP Address is notset. You can check this on your camera Settings System page.If it is empty, you can set it on the TCP/IP settings page, set to your Default Gateway address and this should solve theproblem6.8.4.3 FTP Alarm Sending/FTP Periodic Sending
‐61 ‐If you prefer, you can have the pictures uploaded to an FTP server instead of an email address. There are many choicesfor FTP servers.For example, you could enable the built‐in FTP server function on one of your computers or download free FTP serversoftware such as FileZilla server.Another possibility is to use an online account with FTP access, which is sometimes even available for free with a limitedamount of storage. You can download free FTP client software to manage the FTP server, such as FileZilla client.Yet another option for FTP server is to use a standalone NAS (Network Attached storage) hard drive such as the MyBookWorld Edition.Setup of the FTP alarm sending menu is very similar to setting up the Email alarm Sending/Email periodic sending, sowedon't explain the Snapshot from, Snapshot duration, Snapshot frame rate, Alarm interval,Image file name, Suffix of filename again here.[Enable] Enable task.[Schedule] Option to choose always or set a particular schedule. Check Schedule setup to select the right scheduleID for your task.[Task] Task function. Click on the task to login the task setting screen below.Click Apply to confirm your setting[FTP server name] Type the name or IP address of the FTP server. At a minimum you need the IP address (FTP server name)for your FTP server. The port is almost always 21, and typical servers need a username and password which means
‐62 ‐“Authentication” should be set to “Yes”.[FTP server port] The port number of the FTP server (default is 21).[Remote path] Input the file directory. It is an optional setting to specify a folder on the FTP server. If you decide touse this feature, you have to make sure that the folder exists on the FTP server with the exact same spelling.[Authentication] Select whether authentication is required by the FTP server. Choose “No” for anonymous access.[User name] Type your FTP user name.[Password] Type your FTP password.[Re‐type password] Re‐type your password.Click Apply to confirm your settings.Instead of using motion detection in “FTP alarm sending”, you can also use the “FTP Periodic sending” menu to uploadpictures at regular time intervals.[Period Interval]‐‐Time interval between snapshots. It allows you to designate a time (in seconds or minutes or hours)during which new emails are suppressed. For example, if you want to avoid a flood of emails, you could set this time to60 minutes so that you wouldn’t get any new emails for 1 hour.Note:The menu option for “HTTP alarm sending” and “ HTTP Periodic sending” are not explained here since HTTPservers are only used by network professionals.6.8.4.4 Snapshot to Storage on Alarm/ Snapshot to Storage Periodically[Snapshot from] Select snapshot stream source.[Snapshot duration] The number of seconds that the camera should keep sending images after motion stops.[Snapshot frame rate] The number of frames per seconds that the camera should keep sending images at whenan alarm is triggered.[Alarm Interval]‐‐Number of seconds for which the camera should stop sending e‐mail alerts after the first set.Setting the time to 0 disables this feature. It allows you to designate a time (in seconds) during which new picturesare suppressed. For example, if you want to avoid a flood of pictures, you could set this time to 3600 seconds so thatafter a motion detection event you wouldn’t get any new pictures for at least 1 hour.[Image file name] Name of file image snap shots are saved to[Suffix of file name] Choose between Sequence number andDate Click Apply to confirm your settings.Instead of using motion detection (Snapshot to Storage on Alarm), you can also use the “Snapshot to storage periodically”menu to take snapshots at regular time intervals (Snapshot to Storage Periodically)The “Period Interval” allow you to designate a time (in seconds or minutes or hours) during which new snapshotsare suppressed. For example, if you want to avoid a flood of snapshots, you could set this time to 60 minutes so thatyou wouldn’t get any new snapshots for 1 hour.
‐63 ‐5.8.4.5 Record to Storage on Alarm/ Record to Storage Continuously[Enable] Enable task.[Schedule] Option to choose always or set a particular schedule. Check Schedule setup to select the right scheduleID for your task.[Task] Task function. Click on the task to login the task setting screen below.Click Apply to confirm your setting1. [Record from]‐‐ Select the stream from which it should record. It can be “Primary stream” , “Secondary stream”and “ Mobile Stream” . For smaller pictures you can select from “Secondary stream” or “Mobile Stream”.2. [Post‐recording time]‐‐The number of seconds that the camera should keep recording video after motion stops.If there is any motion within this time the camera will keep recording until there is no motion for the duration ofthis parameter. It can be from 5 seconds to 24 hours.3. [Split duration]‐‐ This specifies the maximum duration of one file. If the recording goes on for longer than thisparameter the camera will split the video into a number of files.4. [Record thumbnail]‐‐ Enable or disable thumbnail.5. [Image file name] ‐‐Name of file image snap shots are saved to6. [Suffix of file name]‐‐ Choose between Sequence number and Date7. Click Apply to confirm your settings.Instead of using motion detection (Record to Storage on Alarm), you can also use the “Record to storage continuously”menu to record video at 24 hours or as per your schedule.5.8.4.6 Send files in storage to FTP server
‐64 ‐[Enable] Enable task.[Schedule] Option to choose always or set a particular schedule. Check Schedule setup to select the right scheduleID for your task.[Task] Task function. Click on the task to login the task setting screen below.Click Apply to confirm your setting[FTP server name] Type the name or IP address of the FTP server. At a minimum you need the IP address (FTP server name)for your FTP server. The port is almost always 21, and typical servers need a username and password which means“Authentication” should be set to “Yes”.[FTP server port] The port number of the FTP server (default is 21).[Remote path] Input the file directory. It is an optional setting to specify a folder on the FTP server. If you decide to usethis feature, you have to make sure that the folder exists on the FTP server with the exact same spelling.[Authentication] Select whether authentication is required by the FTP server. Choose “No” for anonymous access.[User name] Type your FTP user name.[Password] Type your FTP password.[Re‐type password] Re‐type your password.Click Apply to confirm your settingsNote: Once successfully transferred, each original file on the Micro SD card is deleted.5.8.4.7 Push Notification
‐65 ‐[Enable] Enable task.[Schedule] Option to choose always or set a particular schedule. Check Schedule setup to select the right scheduleID for your task.[Task] Task function. Click on the task to login the task setting screen below.Click Apply to confirm your setting[Post time]‐‐The number of seconds that the camera should keep alarm message sending after motion stops. Ifthere is any motion within this time the camera will keep sending alarms until there is no motion for the duration ofthis parameter. It can be from 5 seconds to 24 hours.[Alarm Interval]‐‐Number of seconds for which the camera should stop sending alerts after the first set. Setting thetime to 0 disables this feature. It allows you to designate a time (in seconds) during which new alerts are suppressed.For example, if you want to avoid a flood of alerts, you could set this time to 3600 seconds so that after a motiondetectioneventyouwouldn’tgetanynewalertsforatleast1hour.5.9 Tools MenuThe Tools menu is located on the right of the Settings screen. When you click on the word “Tools”, a sub‐menu ofsetup options will be displayed.
‐66 ‐5.9.1 System Identity[System Name] Type a name to easily identify the camera.[System Contact] Type the contact name of the administrator of the camera. This is useful in large organizations.[System Location] Type the location of the camera. This is useful when using a multi‐camera viewer program.Tip: The information you fill in can be displayed on the camera. It can help to distinguish different cameras on thenetwork.5.9.2 User ManagementAllows you to add or remove users who can view your camera. Useful if you want to allow others to view yourcamera, without having full admin rights.
‐67 ‐[Add] Up to 64 users (including the admin) can be created.Adding users: Click Add on the Camera User List page, then fill in a username and password (twice) and then clickAdd.To edit a user’s password: Click on the user name then enter the new password for that user twice and click Save.To delete a user: Click on the user name then click Delete.Note: A maximum of 16 users are allowed to access the camera simultaneously. As the number of simultaneoususers increases, the overall performance will decrease. This is dependent on the network bandwidth, not thecamera.[Allow anonymous access] This is to be used if you wish to share video with other users, without prompting themfor a user name and password. This will allow the user free access to view the “Live View” page, whereas access tothe Settings page will still be prohibited.[Authentication method] The "basic" authentication scheme is based on the model that the client mustauthenticate itself with a user‐IDandapassword.DigestAccessisamore secure login method as the usernameand password are encrypted before being sent over the internet, however not all systems support Digest AccessAuthentication.5.9.3 Date & TimeAllows you to set the date and time ‐used for the timestamp of any files created by the camera
‐68 ‐[Current device time] Internal time of the camera.[Proposed device time] PC system time. On clicking Apply the internal time of the camera will be changed to thistime.[Select to change the time zone for the device location] Choose your time zone.[Daylight saving time] tick the box to enable daylight saving time. [Dateand Time format] Select the format of the date and time.[Auto time setting (SNTP)] Enable or disable the auto time setting to update to the server below.[Time server] Type the SNTP server name. There are suggestions included.Note:1. If the SNTP server is not found the camera’s time will be synchronized with the PC time.2. The camera keeps track of the time even when power is disconnected.Click Apply to confirm your settings.5.9.4 Backup and ResetAllows you to reset the camera to factory defaults, backup the configuration in case of accidental reset and restoresettings from a backup.
‐69 ‐[Reset] Click Reset to initialize the camera to default factory settings. All users and settings will be lost, requiringyou to reconfigure the camera.[Backup] Click Backup to back‐up the current configuration of the camera for future reference. Once you have yourcamera setup as you require, this is recommended.To restore a backup file:[Browse...] Click Browse... to search for a backup configuration you wish to upload to the camera, then clickRestore.Note: Do not turn off the power during the Restore function since this might corrupt the camera’s firmware5.9.5 Automatic Reboot Setup[Auto reboot] Enable task to keep camera automatic self‐checking the connectivity status.[Reboot Time] Option to choose always or set a particular schedule.
‐70 ‐5.9.6 Firmware UpgradeFrom time to time a new firmware may be released for your model of camera. To check for updates, consult withour technical support before firmware upgrade.Once you have downloaded the latest firmware, store it in a place that is easily to get to. The firmware is in a ZIPfile, which is a compressed file format. You will need to move or copy the file from this compressed folder (someversions of Windows will allow you to do this, but if not, you will need a program like WinZip or WinRAR to unzipthe file to a standard folder). This is very important as the firmware will not update properly if it’s left in thecompressed state.TIPSWe do recommend you update to the latest firmware for your camera whenever werelease one to take advantage of new features and bug fixes. However, this is a seriousprocess and can damage your camera if not done correctly.If your firmware is several versions out ofdate, upgrading straight to the latest one isperfectly fine, you do not need to install each and every update.It is recommended you reboot your computer before attempting this operation andthen close ALL programs that may interfere with the process. Interruption to thisprocess will result in your camera being un‐useable.You may want to backup your settings before the upgrade. You may also want to make anote of your settings before upgrade. The backup/restore configuration may not workbetween firmware upgrades, so always make a note before starting.Click “Tool”, then click “Firmware ”, and you’ll get to this screen :Click “ Continue” , then you will get to this screen. Select Browse... and locate the file you have uncompressed from the ZIP file.Please note: Once you have located the file and selected it, click Upgrade.When you click upgrade, the process will start. This can take 5‐10 minutes. Don’t perform any other actions onyour computer while you are doing this upgrade.
‐71 ‐Wait 3‐5 minute tillthe warning message“Caution ! Upgrading Firmware! Please don’tturnoffpowerorreset the camera tillfirmwareupgrade successfully” displayed.Till warming message above displayed, then Wait 2‐3 minutes again till the message. After the upgrade completes, youwill be prompted “ Firmware upgrade successfully, reboot now ?” to reboot the camera, then click “reboot”, after thisyour latest firmware will be recorded.You can check the camera firmware version in camera “system” ,which is on the top of the right corner .you will get tothe screen . If your firmware upgrade succeed, then the firmware version will be updated.
‐72 ‐5.9.7 Resetting the Camera back to Factory SettingsNote: Do not turn off the power during the Restore function since this might corrupt the camera’s firmware.Ifyoueverforgetyouradminpasswordorhaveanyotherreasontoresetthecameratoitsfactorysettings,pleaseusethe following procedure:1. Make sure the camera is powered up2. For indoor cameras insert the tip ofa paper clip in the hole at the side of the camera to press the reset switch. You’llfeel the click when the switch engages. For outdoor cameras it is easier to use the software reset function in the“Backup or Reset” menu. If hardware reset is needed, Unscrew the entire front part of the camera. It is easiest to doit if you take the sunshield off first. The reset button is right under the Micro SD card slot3. Hold the switch down for at least 5 seconds, then let go. You’ll see the power light go offfor a few seconds. Thisindicates reset is in progress.A few seconds later the camera will restart and is now at factory settings. Of course, after reset the user name andpassword will both be “admin” again (Without quotes). And you may need to set current time zone as shown below.Setting the time and Time ZoneAfter a full reset you may want to make sure the correct time and time is set. This can be done automatically if thecamera has internet access and the setting is enabled as shown below:Appendix A: Wireless setup instructions without Cat5We have received inquiry from customers with no available wired network jack to plug the camera into for the initialconfiguration. For instance, if an Airport Express is used as the only router for a network, the signal network jack istaken by the required connection to the cable or DSL modem.
‐73 ‐While we don’t recommend this, it is still possible to configure the camera without an initial wired connection usingthe following procedure:1. Temporarily rename your Wi‐Fi network name (SSID) to: wirelessnc,andturnoffall wireless security, i.e. nopasswords and no MAC filtering. It is important to have the SSID all lower case and without extra spaces.Then connect to this Wi‐Fi network with your laptop.2. If you are using an Apple airport Express, use the Airport utility as shown on page 6 to reserve a fixed IP addressfor your camera using the camera’s MAC address shown on the back of the camera.3. Power up the camera and wait about 1 minute…the camera should connect to your Wi‐Fi and you should be able toaccess it using the IP address that you reserved for it. If you have a Wi‐Fi router or access point other than theAirport Express, you can connect to your router and look in the DHCP clients list to see the IP address of the cameraif it hasn’t automatically announced itself with a UPnP popup window.4. Now go to the camera’s wireless setup menu, but don’t use the “Search” function. Type in the exact SSID that youhad before the change in step 1, and type the exact password that you wish to use. After you hit “Apply”, youwon’t be able to do further changes until the next step.5. Now set your Wi‐Fi SSID back to the exact same spelling as you entered into the camera’s SSID field, and make surethe password and security mode are also exactly the same. Then update an restart your Wi‐Fi network. You cannow proceed with the setup of the camera as you should be able to see it at the same IP address as in step 3.Appendix B: Setup instructions for ATT (2Wire) RouterOn the ATT/2Wire 2701HG and similar routers we found the UPnp does not work. For access from the internet youneed to log in to the router. ATT usually has the IP address of the router configured to http://192.168.1.254,and thepassword is usually on a sticker on the bottom of the router. Go to the firewall menu, which has section for “HostedApplications “ as shown below:First click on the blue underlined link at the bottom “Add a new user defined application”. That’s 2wire’s terminologyfor port forwarding. two applications need to be defined:The first “application” should be named Cam1HTTP. The public TCP port range is 8150 to 8150 and the “map to hostport” is 80. All other settings should be unchanged.The second application should be named Cam1RTP. The public UDP port range is 30000‐30001 and the “map to hostport” is 30000.After these 2 applications are defined, you select the camera model in the drop down box titled “Choose the computer…” andadd these 2 applications so they are active for your camera. Then you save the settings and restart your router.
‐74 ‐For the next camera, you call the first application Cam2HTTP and use public TCP port 8151 while still using “map tohost” port 80. The second application would be Cam2RTP with UDP ports 30002‐30003 and map‐to‐host port 30002.Appendix C: Manually entering TCP/IP Settings for a CameraIn most cases, this is not required as the router will assign the correct settings to the camera. It is however useful ifyou want to setup the TCP/IP settings of the camera before you connect to it, if DHCP is disabled across yournetwork, or if you have subnet network problems.Assigning an IP address to the Camera with Camera Setup utility1. Launch Camera Setup to detect the camera on your local network.2. Select a camera, click on “Setup” and the following setup interface will pop up. Enter the default setting asbelow:User name : admin; Password: admin
‐75 ‐1. Enter a unique name for the camera, the location (optional) and leave the default port number as 80. “Obtain anIP address automatically” and “Obtain DNS server address automatically” are selected by default, if you areconfident enough to enter your own settings, you can do so by selecting “Use the following IP address” and followthe guidelines on the next page.2. To obtain the IP addresses specific to your network, click “Start” then “Run” and type “cmd” in the text box andclick “Ok”. This will bring up the MS‐DOS prompt. In this window type “ipconfig/all” and press enter. A screensimilar to the one below will be displayed.3. Take note of the following:a. IP Addressb. Subnet Maskc. Default Gatewayd. DNS Servers (Both numbers with the first being the primary DNS server and the second being the secondary DNSserver)4. Enter the details noted in step 6 into the relevant fields in the setup.Note: The default IP address of the camera is 192.168.168.100. This can be changed to any IP address on your IPrange. For example if the IP address of your PC is 192.168.1.52 then the IP address of your camera should beunique and on the same subnet, i.e. 192.168.1.X where X is any number between 1 and 255 except 52. Ensure theIP address you chose is not the same as other devices on your network as this will result in conflict and may causethedevicetonotworkproperly.6. Once you’ve entered the details click “Apply” then “Exit
‐76 ‐Appendix D: Enabling Active X in Internet ExplorerYour browser must have Active X enabled to view the camera in Internet Explorer. To activate this, do thefollowing:1) Open a new Internet Explorer window.2) From the menu bar, select Tools,andthenselectInternet options…3) From the Internet Options window, select the Security tab.4) Click on the Custom Level… button.5) Scroll down to the section labelled ActiveX controls and plug‐ins. Select the option button so that they match thewindow below and then click OK to exit the window.Appendix E: Recovering from a failed Firmware update using WindowsIf you have tried to install a new firmware on your camera, and the procedure has failed, your camera may be
‐77 ‐unresponsive. If the firmware update failed, and your cameras BIOS loader has become corrupted, yourcameras LED will be flashing green when turned on.There is a procedure you can try yourself, however it is quite advanced, so should only be attempted by thosewith a solid understanding of TCP/IP and running commands from the DOS command prompt.Procedure:1. Download the correct new firmware for your camera from our technical support and save this to your hard disk.2. Unzip (uncompress) the firmware to a directory on your PC. Copy the firmware .MFW file to an easy toaccess place, such as C:\firmware.3. Write down the full name of the firmware .MFW filename.4. Connect the camera via the Crossover Cable directly to your computer.5. Open Network Settings on your PC, and make a note of your current TCP/IP Settings.6. Now change your PC Network Setting to the following:IP Address: 192.168.168.50 Subnet Mask: 255.255.255.0Default Gateway: 192.168.168.17. Click OK to save these settings.8. Open an MS‐DOS Command Prompt, or choose “Run” from the start menu and type “cmd.exe”.9. Change the path in the command prompt to the location of the camera firmware (as in step 2) e.g. C:\firmwareand then leave this window open.10. Power off the camera, wait 5 seconds, push down on the reset button on the side of the camera, and withthe reset button still pressed down, power on the camera again.11. Release the reset button. The Green LED should start flashing indicating that the camera is in theFirmware Dump Mode.12. Go back to your Command Prompt window on your PC.13. Type this command in to the prompt: "tftp ‐i 192.168.168.1 put YOUR_FIRMWARE_NAME.mfw"14. You will need to replace YOUR_FIRMWARE_NAME.mfw with the name of the firmware you downloaded (step 3)Press Enter after typing the command.15. The camera's green LED will stop flashing. This means the firmware is being loaded.16. Please wait until the LED starts flashing again – this means the firmware has finished installing.17. Turn the power off to the camera.18. Unplug the crossover cable.19. Restore your TCP/IP Settings to their previous state (as in step 5)Your camera should now be restored to its factory default settings and be working again – you can proceed tothe start of the manual and setup your camera as normal.Appendix F: Connecting your Camera directly to a ComputerYou can also connect the camera directly to a computer. Please note that in this mode you will not be able toview your camera from anywhere else apart from the computer you are currently using.1. Connect one end of the network cable in to the Camera Network Connection socket, and plug the other end into a spare network port on your computer.2. Connect the included power adapter to the power port on the camera and the other end into an electrical socket.
‐78 ‐Do not turn the power on at this time.You must then assign your computer an IP address so it can talk easily to the camera.On a PC:1. Open the Control Panel and double click on “Network Connections” then right click on your “Local AreaNetwork” connection, and click Properties. Be sure to select the Network icon that corresponds to where you haveplugged the camera in to – so this would not be listed as a Wireless, Wi‐Fi or Bluetooth Network.2. Select “Internet Protocol (TCP/IP)” then click Properties.3. Take note of your current TCP/IP Settings and then click on “Use the following IP settings”4. In the “IP Address” Field type in the number 192.168.168.205. In the “Subnet Mask” type in 255.255.255.06. In the “Default Gateway” type 192.168.168.1 or leave it blank(The camera will automatically assign itself thisIP address when no DHCP server is present)7. Leave DNS server settings blank.8. Click “OK” then “Close” to apply these settings.9. Turn the power on to the camera.10. The Connectivity Status indicator on the front of the camera will light up.You can now proceed to the Software Installation section.On a Mac:1. Open “System Preferences” from the dock, and then select “Network” to edit your network settings. Asthe Y‐cam is connected to your Mac using a cable we must choose the “Built‐in‐Ethernet” option. Select“Built‐in Ethernet” and click the “Configure” button. Make a note of your current TCP/IP Settings.2. Select “Manually” from the IPv4 drop‐down box at the top of the dialog, and then enter these settings:IP Address: 192.168.168.20Subnet Mask: 255.255.255.0Router/Default Gateway: 192.168.168.1 or leave it blankDNS Servers: Leave blank, not important at this stage.Search domains: Optional, leave blank, not important.3. The click “Apply Now”.4. Turn the power on to the camera.5. The Connectivity Status indicator on the front of the camera will light up.You can now proceed to the Software Installation section.Appendix G: Burglar Alarm system integration with digital I/OThe outdoor cameras have additional connectors to help with integration of the cameras into a complete burglaralarm system.Typically this type of wiring is carried out by a professional security system installer. If you are not familiar with theterminology used here, please do not attempt to connect anything to this terminal block. Damage caused byimproper wiring is not covered by warranty.When the camera senses motion, and if the digital output is set to “Enable” in the camera’s “Digital I/O Setup” menu, it
‐79 ‐activates the digital output to trigger a burglar system. With a Maximum voltage of 60V, this output has an opencollector NPN Darlington transistor with the emitter connected to the GND pin. If used with an external relay a reversepolarity diode must be connected in parallel with the relay coil to protect against voltage transients. You would need toselect a relay that uses less than 0.4A at 12V, and the relay and the diode would connect pins 3 and 4.Conversely, if the digital input is set to “ Enable” in the camera’s “Digital I/O Setup” menu, a contact closure from DI to GND(pins 1 and 2) would trigger an alarm condition in the camera as if the camera’s own motion detection had triggered.This means that emails or FTP/HTTP uploads can be triggered or recording to Micro SD card can be initiated. Both thedigital input and the camera’s motion detection can be active at the same tie. If you only want this external input totrigger the camera’s alarms you need to set all 4 motion detection windows in the “ Motion detection “ menu todisable (unchecked)The round connector at the end of the wiring harness that looks similar to the power plug is for optional attachment ofan amplified speaker system. This output is at line level similar to a computer speaker system. Using this, audio uploadcan be initiated from the Microphone of a computer running Internet Explorer. There is no echo suppression, so if thisis used it would make sense to turn down the camera’s own microphone.6.0 TroubleshootingProblem Cause and RemedyI forgot the IP address of the 1. Use the camera Setup program.cameraI forgot my password to 1. You will need to press the RESET button. Note: all configuration settings will be lost.access the Settings menuWi‐Fi connectivity doesn’t 1. Signal strength is weak. Relocate the camera nearer to your router or remove thework. obstacles between the two.2. Make sure your wireless network SSID and Encryption settings are identical to yournetworks.3. Check for any interference from other equipment.The picture viewing 1. Check that your Internet Explorer settings allow you to download and install ActiveXinterface does not appear. controls.2. Maximum 16 users are allowed to access the camera simultaneously through thenetwork.3. Network traffic may prevent the viewing interface from appearing quickly. Wait for awhile.4. Refresh the page.The color of the picture is 1. Confirm the colour setting ofPC is 16 bits or more.strange. 2. Identify which camera’s model you have, Infrared versions ofthe camera sometimeshave shades of color spectrum alter the images the camera displays due to the InfraredLEDs.Unreadable characters are 1. Set the Encoding or the Character Set ofthe selected language on the web browserdisplayed.I cannot see the controls of1. Reset your browsers Zoom setting or text size setting – pressing Ctrl and “0” (zero) at thethe Live Feed as the pictures same time should do this.goes over them 2. Try to find settings that reset your page zoom or text zoom.The motion detection 1. Check the e‐mail alert feature is properly configuredfeature does not send e‐mail 2. The SMTP server that the IP camera uses to send the e‐mail may be filtering e‐mail toalerts. prevent spam from being sent from your server. Try using a different SMTP server orcontact your ISP to see ifSMTP access is being blocked.3. Your Primary DNS IP Address may not be setThe power LED is flashing 1. A firmware upgrade has been interrupted or the firmware has otherwise been damaged.
‐80 ‐green and the camera is Please contact your place ofpurchase or TriVision Technical SupportinaccessibleMotion Detection triggers 1. Motion detection is based on changes in pixel in the image. This means that ifthere areunexpectedly sudden changes in the lighting, motion detection may be triggered mistakenly. Lower thesensitivity setting to avoid problems.What do the changes to Amber ‐Steady for connection to a 10/100 M bit/s network.the LED light mean? Amber ‐Flashes for network activity. Green ‐Steady for connection to a wirelessnetwork.Green ‐Flashes for network activity.7.0 Installation Instruction7.1 3G Solar Camera Install7.2 SPY Camera Instal
81FCC STATEMENT :This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.Warning: Changes or modifications not expressly approved by the party responsible for compliance could void theuser's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates uses and can radiate radio frequency energyand, if not installed and used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can be determined by turningthe equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver. Connect the equipment into an outlet on acircuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TVtechnician for help.FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Thisequipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Navigation menu