Andersen CB00011072301 Intrusion Detector-400-DH Sensor User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2992431
Application ID	z7WKqnLMT8yH6WqwYyD5PQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	194.27kB (2428387 bits)
Date Submitted	2016-05-16 00:00:00
Date Available	2016-05-16 00:00:00
Creation Date	2016-03-08 10:13:59
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2016-03-08 10:14:49
Document Title	Users Manual
Document Creator	Adobe InDesign CC 2014 (Macintosh)

VeriLock® Security Sensor Application
VeriLock® Security Sensor Application
for Andersen® A-Series Frenchwood Gliding, 400 Series Frenchwood® Gliding, 200 Series Narroline® Gliding and
200 Series Perma-Shield® Gliding Patio Doors
for Andersen® A-Series Frenchwood Gliding, 400 Series Frenchwood® Gliding, 200 Series Narroline® Gliding and
200 Series Perma-Shield® Gliding Patio Doors
Thank you for choosing Andersen. / Gracias por elegir Andersen.
For questions call 1-888-888-7020. For more information and/or guides visit andersenwindows.com.
Please leave this guide with building owner.
Si tiene alguna pregunta llame al 1-888-888-7020. Para obtener más información y/o guías, visite andersenwindows.com.
Deje esta guía con el dueño de la construcción.
▶▶ Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
Lea completamente la guía antes de comenzar la instalación. Lea y respete todas las advertencias y precauciones durante la instalación de la unidad.
▶▶ Check with your local building code official to identify and confirm compliance with local building code requirements.
Consulte los códigos locales de construcción para identificar y confirmar que se cumplan los requisitos del código de construcción.
Parts Included / Partes Incluidas
(1) Instruction Guide / Guía de instrucciones
(4) VeriLock Face Plate /
		 Placa frontal VeriLock
(1) VeriLock Sensor / Sensor VeriLock
(1) Actuator / Accionador
(1) CR-2032 Battery / Batería CR-2032
(1) Magnet / Imán
(2) #6 x 1" Screw / Tornillo No. 6 x 1"
(12) #10 x 2" Screw / Tornillo No. 10 x 2"
(2) Spacer (Tribeca® Hardware Only) / 		
Espaciador (Solo para herrajes Tribeca®)
VeriLock®
Face Plate
Placa frontal
VeriLock
Actuator
Accionador
Tools Needed /
Herramientas Necesarias
∙∙ Safety Glasses / Lentes de seguridad
∙∙ Phillips Screwdriver / Destornillador Phillips
∙∙ Drill/Driver / Taladro/destornillador
∙∙ 1/8" Drill Bit /Broca para taladro de 1/8"
∙∙ Drop Cloth / Tela protectora
VeriLock®
Sensor
Sensor
VeriLock®
#6 x 1" Screw
Tornillo No. 6 x 1"
Magnet
Imán
Spacer
(Tribeca® hardware only)
Espaciador
(Solo para herrajes
Tribeca®)
CR-2032 Battery
Batería CR-2032
#10 x 2" Screw
Tornillo No. 10 x 2"
Depending on individual installation requirements, some parts may not be used.
Es probable que no sean necesarias algunas piezas. Esto depende de los
requisitos de instalación individual.
Use caution when working at elevated heights and around unit openings.
Follow manufacturers’ instructions for ladders and/or scaffolding. Failure
to do so may result in injury or death.
Sea cauteloso al trabajar en lugares elevados y cerca de las aberturas de
la unidad. Siga las instrucciones del fabricante para el uso de escaleras
y/o andamios. Si no lo hiciera, podrían producirse lesiones o la muerte.
Follow manufacturers’ instructions for hand or power tools. Always
wear safety glasses. Failure to do so may result in injury and/or
product damage.
Siga las instrucciones del fabricante para el uso de herramientas
eléctricas o manuales. Utilice siempre gafas de seguridad. Si no lo
hiciera, podrían producirse lesiones y/o daños al producto.
“Andersen” and all other marks where denoted are trademarks of Andersen Corporation and its subsidiary. © 2016 Andersen Corporation. All rights reserved.
“Andersen” y todas las demás marcas que aparezcan son marcas registradas de Andersen Corporation y su subsidiaria © 2016 Andersen Corporation. Todos los derechos reservados.
9 1 3 6 2 7 0 BA - 0 1
Revised 03/04/16
Batteries carry the risk of fire, explosion and burns. Do not recharge,
disassemble, heat above 212 degrees F (100 degrees C) or
incinerate. Dispose of used batteries promptly and properly. Keep
away from children.
Les piles représentent un risque d’incendie, d’explosion et de
brûlures. Ne pas recharger, démonter, chauffer à une température
excédant 100 degrés C (212 degrés F) ou incinérer. Éliminer les piles
rapidement et de manière appropriée. Garder à l’écart des enfants.
Magnetic field can be harmful to implanted medical device wearers.
Keep magnets away from devices.
El campo magnético puede dañar a personas con dispositivos médicos
implantados. Mantenga los imanes lejos de los dispositivos.
Batteries are small parts and, if swallowed, could pose a choking
hazard to young children.
Magnets are small parts and, if swallowed, could pose a choking
hazard to young children.
Los imanes son partes pequeñas que, en caso de ingesta, pueden
representar un riesgo de asfixia para niños pequeños.
Las baterías son partes pequeñas que, en caso de ingesta, pueden
representar un riesgo de asfixia para niños pequeños.
Interior
Latch Lever
Palanca del pestillo
Phillips
Screwdriver
Destornillador
Phillips
Lay a drop cloth down to prevent losing parts. Unlock and open door. Remove latch lever. Save latch
lever for reuse and discard screws.
Lay a drop cloth down to prevent losing parts. Unlock and open door. Remove latch lever. Save latch
lever for reuse and discard screws.
9136270
2
Indicator Light
Luz indicadora
Interior
VeriLock®
Face Plate
Placa frontal
VeriLock
VeriLock®
Sensor
Assembly
VeriLock®
Sensor
Assembly
VeriLock
Sensor
Sensor
VeriLock
Battery
(+ facing out)
Batería
(polo + hacia afuera)
Sensor Tab
Lengüeta
del sensor
(back views)
(vistas traseras)
Actuator
Accionador
(Rotate actuator, then
insert into hole, to avoid
damage to sensor tab).
(Gire el accionador y
después inserte en
el orificio, para evitar
daños en la lengüeta
del sensor).
(back views)
(vistas traseras)
(front view)
(vista frontal)
Select preferred color VeriLock face plate. Press sensor into back side of face plate. Install actuator as shown and battery with (+) facing out as
shown. Indicator light will illuminate for one second when battery is installed correctly.
Seleccione el color preferido de la placa frontal. Presione el sensor en la parte trasera de la placa frontal. Instale el accionador y coloque la
batería con el polo positivo (+) hacia afuera, tal y como se muestra. La luz indicadora se iluminará por un segundo cuando la batería esté
instalada correctamente.
Tribeca® Hardware Only
Solo para herrajes Tribeca®
Interior
Spacer
Espaciador
Position between.
Posición intermedia.
VeriLock®
Assembly
VeriLock®
Assembly
VeriLock®
Assembly
Ensamble
Verilock
Latch
Lever Pin
Latch
Lever Pin
(front view)
(vista frontal)
Latch Lever
Palanca del pestillo
(back views)
(vistas traseras)
Insert latch lever
pin through
actuator slot.
Inserte la espiga
de palanca del
pestillo a través
de la ranura del
accionador.
Insert latch lever pin through actuator slot as shown.
Insert latch lever pin through actuator slot as shown.
9136270
Tribeca
Latch Lever
Palanca
de pestillo
Tribeca
For Tribeca hardware only, select preferred color
spacer and position between the VeriLock sensor
assembly and Tribeca latch lever as shown.
For Tribeca hardware only, select preferred color
spacer and position between the VeriLock sensor
assembly and Tribeca latch lever as shown.
4
Interior
Sensor contains an anti-tamper switch. Do not apply sensor over wet
finish or rough/dirty surface. Improper switch function may result.
El sensor contiene un interruptor de seguridad. No instale el sensor en
acabados húmedos o superficies sucias/ásperas. Esto podría dar como
resultado un mal funcionamiento del interruptor.
Latch Lever
(unlocked position)
Palanca del pestillo
(en posición de
desbloqueo)
Indicator
Light
Luz
indicadora
VeriLock Sensor
(anti-tamper switch)
Sensor VeriLock
(interruptor de
seguridad)
(front view)
(vista frontal)
#10 x 2" Screws
(included)
#10 x 2" Screws
(included)
(back view)
(vista trasera)
Verify panel surface is clean and dry. Position latch lever and VeriLock sensor assembly on panel as shown and fasten using #10 x 2" screws
included. The indicator light will illuminate for one (1) second when the sensor assembly is applied to the panel as the anti-tamper switch is
depressed.
Verify panel surface is clean and dry. Position latch lever and VeriLock sensor assembly on panel as shown and fasten using #10 x 2" screws
included. The indicator light will illuminate for one (1) second when the sensor assembly is applied to the panel as the anti-tamper switch is
depressed.
Magnet Application/ Aplicación del imán
Magnets are small parts and, if swallowed, could pose a choking hazard to young children.
Los imanes son partes pequeñas que, en caso de ingesta, pueden representar un riesgo de asfixia para niños pequeños.
Interior
Do not pinch or drill through weatherstrip. Product
damage will occur.
Do not pinch or drill through weatherstrip. Product
damage will occur.
Side jamb and weatherstrip shown transparent for clarity.
La jamba lateral y el burlete se muestran transparentes para
que haya claridad.
Magnet / Imán
Side Jamb
Interior Side
Jamba lateral
Lado interior
1/8" Drill Bit
Broca para taladro
de 1/8"
Weatherstrip
Burlete
Lock Receiver
Receptor del cerrojo
#6 x 1" Screw
Tornillo n.° 6 x 1"
Phillips Screwdriver
Destornillador Phillips
Position magnet on side jamb behind weatherstrip. Slide tight to interior edge of lock receiver as shown and pre-drill two (2) 1/8" holes, 3/4"
deep using magnet holes as a template. Fasten with two (2) #6 x 1" screws.
Position magnet on side jamb behind weatherstrip. Slide tight to interior edge of lock receiver as shown and pre-drill two (2) 1/8" holes, 3/4"
deep using magnet holes as a template. Fasten with two (2) #6 x 1" screws.
9136270
Verify VeriLock Sensor Function / Verifique el funcionamiento de sensor VeriLock
Interior
Indicator Light
Luz indicadora
Latch Lever
(unlocked position)
Palanca del pestillo
(en posición abierto)
Latch Lever
(locked position)
Palanca del pestillo
(en posición cerrado)
1.
2.
3.
4.
Close door without locking. Indicator light will illuminate for one (1) second.
Lock door with latch lever. Indicator light will illuminate for one (1) second. Verify door is locked.
Unlock door with latch lever. Indicator light will illuminate for one (1) second.
Open door. Indicator light will illuminate for one (1) second.
1.
2.
3.
4.
Close door without locking. Indicator light will illuminate for one (1) second.
Lock door with latch lever. Indicator light will illuminate for one (1) second. Verify door is locked.
Unlock door with latch lever. Indicator light will illuminate for one (1) second.
Open door. Indicator light will illuminate for one (1) second.
Verify VeriLock sensor function. If indicator light does not respond as described, verify sensor application and magnet placement.
Verifique el funcionamiento del sensor VeriLock. Si la luz indicadora no funciona como se describió anteriormente, verifique la aplicación del
sensor y la ubicación del imán.
▶▶ Procedure is complete.
El procedimiento se ha completado.
Refer to monitoring system of your choice for sensor enrollment. /
Consulte el sistema de monitoreo de su elección para el registro del sensor.
For maintenance information, please visit http://www.andersenwindows.com/verilock and consult with the VeriLock® user guide.
Para obtener información de mantenimiento, visite http://www.andersenwindows.com/verilock y consulte con la guía del usuario de VeriLock®.
9136270
Regulatory Statements / Normas reglamentarias
Federal Communications Commission (FCC)
Part 15 Statement
This device complies with FCC Rules Part 15. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference. (2) This device must accept any
interference that may be received, including interference that
may cause undesired operation.
Industry Canada (IC) RSS Statement
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device
must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1)
I'appareil ne doit pas produire de brouillage; (2) I'utilisateur de
I'appareil doit accepter tout brouillage radioélectrique subi,
méme si le brouillage est susceptible d'en compromettre le
fonctionnement.
Changes or modifications not expressly approved by Andersen
may void the user's authority to operate the equipment.
9136270

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Instance ID                     : uuid:fffe11eb-aa2b-fc47-9a15-320db52347ae
Original Document ID            : adobe:docid:indd:d0717119-dfee-11de-8e34-9beae8c19d6b
Document ID                     : xmp.id:9842280c-d6c1-4923-ac58-6e2b78f72d50
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:19b20714-6428-4803-ada7-a4e6590d7267
Derived From Document ID        : xmp.did:1451f951-024c-4690-9f10-b8a4a1897563
Derived From Original Document ID: adobe:docid:indd:d0717119-dfee-11de-8e34-9beae8c19d6b
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2014 (Macintosh)
History Changed                 : /
History When                    : 2016:03:08 10:13:59-06:00
Create Date                     : 2016:03:08 10:13:59-06:00
Modify Date                     : 2016:03:08 10:14:49-06:00
Metadata Date                   : 2016:03:08 10:14:49-06:00
Creator Tool                    : Adobe InDesign CC 2014 (Macintosh)
Format                          : application/pdf
Producer                        : Adobe PDF Library 11.0
Trapped                         : False
Slug Family                     : Helvetica
Slug Version                    : 001.004
Slug Outline File Size          : 30185
Slug Kerning Checksum           : 55007
Slug Foundry                    : Adobe Systems
Slug Font Kind                  : PostScript
Slug Checksum                   : 3285313313
Slug Post Script Name           : Helvetica-Condensed
Slug Font Sense 12 Checksum     : 3285313313
Page Layout                     : SinglePage
Page Mode                       : UseThumbs
Page Count                      : 6
Creator                         : Adobe InDesign CC 2014 (Macintosh)

EXIF Metadata provided by EXIF.tools