Andrew Wireless Innovations Group RPT-MR703P Repeater User Manual User sManual

Andrew Wireless Innovations Group Repeater User sManual

Users manual

USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 1 22-Jan-01 User´s manual for band selective repeater MRx03P
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 2 22-Jan-01 Copyright  MIKOM, Buchdorf 2001 All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system, transmitted in any form or by any means, electronical, mechanical photocopying, recording or otherwise, without prior written permission of the publisher.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 3 22-Jan-01 TABLE OF CONTENTS 1. GENERAL 7 1.1. LIST OF ABBREVIATIONS 7 1.2. HEALTH AND SAFETY WARNINGS 8 1.3. PREAMBLE 9 1.4. LIST OF INTERNATIONAL SALES OFFICES 10 2. FUNCTIONAL DESCRIPTION 11 2.1. GENERAL 11 2.2. REPEATER DESIGN 11 2.3. COMPONENTS OF THE MRX03P 12 2.3.1. Duplexer 12 2.3.2. Measuring Aids 12 2.3.3. Conversion Module 13 2.3.4. Final Amplifier 14 2.3.5. Control Module 15 2.3.6. Motherboard 16 2.3.7. Power Supply 17 3. OPTIONAL EQUIPMENT 18 3.1. MODEM 18 3.1.1. Initstrings 18 3.1.2. PSTN Modem 19 3.1.3. Wireless Modem 20 3.2. EXTERNAL ALARMS 21 3.3. BATTERY BACKUP 22 4. INSTALLATION 23 4.1. MECHANICAL INSTALLATION 23 4.1.1. General 23 4.2. WALL MOUNTING PROCEDURE 24 4.2.1. Pole Mounting Procedure 25 4.3. ELECTRICAL INSTALLATION 27 4.3.1. Grounding 27 4.3.2. Mains Power Supply 27 4.3.3. Antennas Connections 28
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 4 22-Jan-01 5. COMMISSIONING 29 5.1. PREPARATION 29 5.1.1. General 29 5.1.2. BCCH-Channel 29 5.1.3. Antenna Isolation 30 5.2. BOOT PROCESS 31 5.3. DIP-SWITCHES 32 5.4. REMOTE SETTINGS 33 5.4.1. Local Login 33 5.4.2. Remote Login 35 5.5. MANUAL SETTINGS 36 5.6. LEVELLING OF THE REPEATER 38 6. ALARMS 39 6.1. BITE AND ALARMS 39 6.2. HANDLING OF ALARMS 39 6.3. STATUS REPORT 39 7. TROUBLE SHOOTING 40 7.1. ERROR INDICATION 40 7.2. BOOT PROCESS 41 7.3. ALARM MONITORING WITH THE ALARM HISTORY 41 7.4. POWER SUPPLY 41 7.5. GENERAL REMARKS 42 8. MAINTENANCE 43 8.1. GENERAL 43 8.2. REPLACEMENT OF THE FUSES 44 8.3. REPLACEMENT OF THE MAINS CABLE 44 8.4. REPLACEMENT OF THE RAM / RTC BATTERY 45 8.5. REPLACEMENT OF THE BATTERY BACKUP MODULE 47 8.6. DUPLEXER 48
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 5 22-Jan-01 8.7. CONVERSION MODULE 48 8.8. CONTROL MODULE SM 2009 49 8.9. POWER SUPPLY 49 8.10. CONNECTING BOARD 50 9. APPENDIX 51 9.1. ELECTRICAL SPECIFICATIONS 51 9.1.1. Specifications of MR703P 51 9.1.2. Specifications of MR803P 52 9.2. MECHANICAL SPECIFICATION 53 9.3. ENVIRONMENTAL AND SAFETY SPECIFICATIONS 53 9.4. SPARE PARTS LISTS 54 9.4.1. Spare Parts List of MR703P 54 9.4.2. Spare Parts List of MR803P 55 9.5. INSTALLATION DRAWING OF THE REPEATER 56 9.6. LAYOUT OF THE REPEATER LID 57 9.7. LAYOUT OF THE REPEATER HEAT SINK 58 10. INDEX 59
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 6 22-Jan-01 LIST OF FIGURES AND TABLES figure 2-1 Configuration of a MRx03P ...................................................................................11 figure 2-2 Duplexer.....................................................................................................................12 figure 2-3 Conversion module .................................................................................................13 figure 2-4 Final amplifier ...........................................................................................................14 figure 2-5 Control module .........................................................................................................15 figure 2-6 Motherboard..............................................................................................................16 figure 2-7 Power supply ............................................................................................................17 figure 1-1 Location of the PSTN Modem...............................................................................19 figure 1-2 Modem connection on the duplexer ....................................................................20 figure 3-3 Location of external alarm clamps.......................................................................21 figure 3-4 Location of the battery backup module...............................................................22 figure 4-1 Installation drawings of a repeater.......................................................................24 figure 4-2 MIKOM pole mounting kits. ...................................................................................25 figure 4-3 Grounding bolt ..........................................................................................................27 figure 4-4 Top view of antenna connections ........................................................................28 figure 5-1 Control module – Position of LEDs......................................................................31 figure 5-2 Control module – Position of the DIP-switches.................................................32 figure 5-3 Motherboard..............................................................................................................36 figure 8-1 Fuse replacement....................................................................................................44 figure 8-2 Connecting board ....................................................................................................44 figure 8-3 Cable gland ...............................................................................................................45 figure 8-4 Position of RAM/RTC battery................................................................................46 figure 8-5 Battery backup module...........................................................................................47 figure 8-6 Connecting board ....................................................................................................50 figure 9-1 Installation drawing of MRx03P............................................................................56 figure 9-2 Repeater lid...............................................................................................................57 figure 9-3 Repeater heat sink ..................................................................................................58 table 1-1 Standard initstrings for modems............................................................................18 table 5-1 LED indication during boot process......................................................................31 table 5-2 DIP-switches of control module .............................................................................32 table 5-3 Rotary switches of the motherboard.....................................................................37 table 9-1 Specification of MR703P .........................................................................................51 table 9-2 Specification of MR803P .........................................................................................52 table 9-3 Spare parts list of MR703P.....................................................................................54 table 9-4 Spare parts list of MR803P.....................................................................................55
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 7 22-Jan-01 1. GENERAL 1.1. LIST OF ABBREVIATIONS ALC Automatic Level Control BCCH Broadcast Control Channel BITE Built In Test Equipment BTS Base Transceiver Station DL Downlink ESD Electrostatic Discharge ETS European Telecommunication Standard I2C-Bus Inter Integrated Circuit Bus (Philips) Id.-No. Identification Number MR MIKOM Repeater MS Mobile Station OMC Operation and Maintenance Center PCMCIA Personal Computer Modem Communication International Association PCS Personal Communication System PSTN Public Switched Telephone Network Rev Revision RF Radio Frequency SCL Serial Clock SDA Serial Data UL Uplink
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 8 22-Jan-01 1.2. HEALTH AND SAFETY WARNINGS ∗ Note: The electrical installation has to be performed in accordance with the safety regulation of the local authorities. Due to safety reasons, the electrical installation must be carried out by qualified personnel. The cover of this unit should not be opened while power is applied. Subsequent installation, commissioning and maintenance activities that require the unit to be powered with the cover open shall only be carried out by suitably qualified personnel. ∗ Note: The grounding of the unit has to be performed by all means. A grounding bolt is provided at the outside of the cabinet to connect the earth bonding cable. ∗ Note: Make sure that a suitable mounting surface is used. Only adequate manpower is allowed to handle the system. ∗ Note: ESD precautions must be observed! Before maintenance work, use the available grounding system to connect ESD protection measures. ∗ Note: Due to power dissipation, the repeater may heat up the air volume inside the cabinet and reaches a very high temperature Therefore, it is recommended to mount the repeater in the vertical plane to a wall or a mast without additional enclosure to provide sufficient ventilation. Between the housing and the wall, a minimum distance must be kept to provide air circulation. ∗ Note: Close the repeater housing only after a thorough control of the cable layout to avoid any damage of the cables.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 9 22-Jan-01 1.3. PREAMBLE MIKOM is a leading manufacturer of coverage equipment for mobile radio networks, specializing in low cost, high performance, RF and optical repeaters. Our optical distributed networks and RF repeater systems provide coverage for every application; outdoor use, indoor installations, tunnels, subways and many more. MIKOM has engineering and manufacturing facilities in Germany, Italy and the USA. In addition, MIKOM maintains many field engineering and sales offices throughout the world. All equipment is manufactured using only highly reliable materials. In order to ensure constant first-rate quality of the products, a comprehensive quality assurance has been conducted at all fabrication stages. Every component leaves the factory only after a thorough final acceptance test, accompanied by a test certificate guaranteeing optimal function. Any intervention must be carried out by authorized persons only. If technical assistance for the product is required, please contact the local sales office or contact MIKOM directly at one of the following addresses: MIKOM GmbH Industriering 10 86675 Buchdorf Germany Tel: +49 (0) 9099 69 0 Fax: +49 (0) 9099 69 31 E-mail: sales@mikom.com http://www.mikom.com for The Americas: MIKOM US Phone: +1 (0) 800-800-7465 E-mail: MIKOM_US_sales@allentele.com When set-up is performed according to this manual, the system will operate without complications for a significant length of time.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 10 22-Jan-01 1.4. LIST OF INTERNATIONAL SALES OFFICES Allen Telecom Inc. 31225 Bainbridge Road, Suite J, Cleveland Ohio 44 139-2293 USA Phone: +1 (440) 519-2629 FAX: +1 (440) 519-8607 Allen Telecom Pty Ltd 6 Stuart Street Padstow NSW 2211 Australia Phone: +61 (2) 9774-4200 FAX: +61 (2) 9774-4500 Forem France Z.I. des Ebisoires 78370 Plaisir France Phone: +33 (1)30-79-15-36 FAX: +33 (1) 30-55-55-37 FOREM S.p.A. Via Archimede 22/24 20041, Agrate Brianza Milan Italy Phone: +39 (039)605-4453 FAX: +39 (039) 605-4477 AT Singapore 80 Marine Parade Road #19-1 Parkway Parade Singapore 449269 Phone: +65 (345) 8022 FAX: +65 (345) 8033 AT China CITIC Building, # 11-04 19 Jianguomenwai Avenue Beijing 100004 China Phone: +86 (10) 6508-3088 FAX: +86 (10)6508-3066 AT Canada 1815 Ironstone Manor, # 12 Pickering, Ontario L1W 3W9 Canada Phone: +1 (905) 839-3474 FAX: +1 (905) 839-4663 FOREM UK Unit D Castle Industrial Park Pear Tree Lane, Newbury RG 14 2EZ, Berkshire U.K. Phone: +44 (1635) 569-695 FAX: +44 (1635) 569-463 AT India F-1 Adarshini Plaza 93, Adchini SRI Aurobindo Road New Delhi-110017 India Phone: +91 (11) 653-2126 FAX: +91 (11) 653-2120 MIKOM Austria Weglgasse 10 2320 Schwechat Austria Phone: +43 (1) 706 – 3999 FAX: +43 (1) 706 – 39999 MIKOM Switzerland Tiergartenweg 1 4710 Balsthal Switzerland Phone: +41 (6238) 61260 FAX: +41 (6238) 61261 C-COM Czech Republic U Morusi 888 530 06 Pardubice-Svitkov Czech. Republic Phone: +42 (0406) 301280 FAX: +42 (0406) 301298
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 11 22-Jan-01 2. FUNCTIONAL DESCRIPTION 2.1. GENERAL Cellular telephone systems transmit signals in two directions between base transceiver station (BTS) and mobile stations (MS) within the signal coverage area. If weak signal transmissions occur within the coverage area because of indoor applications, topological conditions or distance from the transmitter, a repeater is used to extend transmission range. In the downlink (DL) path, the repeater picks up the signal from a donor antenna of an existing cell, processes and retransmits it into the desired dark spot. In the uplink (UL) direction, the repeater receives a signal from mobile stations present in its coverage area and forwards them to the corresponding BTS. 2.2. REPEATER DESIGN The repeater MRx03P is a band selective amplifier which bi-directionally amplifies signals between a base transceiver station and mobile stations in the corresponding network. It can provide highly selective amplification, thus enabling radio coverage in regions where satisfactory quality of communication is disabled. The following figure shows the configuration of a MIKOM repeater MRx03P. figure 2-1 Configuration of a MRx03P The MRx03P can also be combined with other repeater systems to create a combined repeater system. When different modules are combined, a common antenna terminal and a common control interface is available.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 12 22-Jan-01 2.3. COMPONENTS OF THE MRX03P The actual repeater configuration can be seen at the configuration list which is part of the delivery. 2.3.1. Duplexer The task of the duplexer is to isolate uplink from downlink, i.e. to separate the transmitting path from the receiving path. The pass bandwidth of the duplexer is the entire width of the UL- and DL band of the corresponding network. figure 2-2 Duplexer 2.3.2. Measuring Aids With built-in RF probes at the duplexers, test signals can be applied or detected (see figure 2-2). The probes are provided with different coupling factors, 30 dB for measurements and 20 dB for the optional modem. Each antenna port is equipped with one coupler. This facilitates measurements under all operational conditions while an antenna or a dummy load may be connected. Modem connect. (20dB) 30dB Coupler
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 13 22-Jan-01 2.3.3. Conversion Module The task of the conversion module is to amplify the received signals and to convert them into an intermediate frequency. Then, the signals proceed a filter stage comprising of highly selective filters and run through a digital controllable attenuator. figure 2-3 Conversion module Each link of a conversion module is provided with filters which guarantee the high selectivity. There the desired bandwidth and the desired centre frequency can be set. By using the same synthesizer frequency, that was used to convert the signals down to intermediate frequency, the intermediate frequency is mixed up to the original frequency. The synthesizer is controlled via an I2C-Bus.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 14 22-Jan-01 2.3.4. Final Amplifier The UL- and DL path are amplified by a final amplifier. It is located next to the conversion module. figure 2-4 Final amplifier
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 15 22-Jan-01 2.3.5. Control Module The control module is a DOS compatible micro computer. The whole communication between the provider and the repeater can be done via the control module. The repeater can be controlled remotely or locally via a VT100 terminal or a PC emulating the VT100 terminal. To control the repeater remotely, use either the RS232 interface in connection with a wireless modem or the PCMCIA interface in connection with a modem card and a mobile or PSTN network adapter. The RS232 interface and the PCMCIA interface are located on the control module. Frequency, gain, power down of RF stages and ALC can be controlled and status messages can be received remotely. In case a PSTN modem or a mobile is connected, automatic alarm messages can be received. The data transfer between the control module and the mother board is realized by the I2C-Bus system. The I2C-Bus concept was developed by Philips for the serial connection of integrated circuits within one device. Two wires, serial data (SDA) and serial clock (SCL), carry information between the devices connected to the bus. Each device is recognized by a unique address and can operate either as transmitter or receiver. All MRx03P configuration parameters are non-volatile stored in an EEPROM on the control module if power supply failure occurs. figure 2-5 Control module
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 16 22-Jan-01 2.3.6. Motherboard The function of the mother board is the communication between the conversion module and the control module via the I2C-Bus. All signals will be recognized from the mother board logic. figure 2-6 Motherboard
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 17 22-Jan-01 2.3.7. Power Supply The power supply can be provided by different mains power. An external switch, mounted on the power supply, is provided to disconnect the repeater from mains during maintenance work to ensure that all circuits are voltage-free. The power supply is factory-set and must not be changed. The power supply can be fuse-protected. figure 2-7 Power supply External Switch
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 18 22-Jan-01 3. OPTIONAL EQUIPMENT The actual repeater configuration can be seen at the configuration list which is part of the delivery. 3.1. MODEM The modem option enables the provider to set parameters and to query the status of each repeater remotely. Furthermore, the modem can be set to send all occurred alarms of the repeater directly to a provider’s terminal, e.g. to the OMC. This can be done either via a wireless modem or a PSTN modem (Public Switched Telephone Network). Thus, the alarms can be evaluated and eliminated promptly. It is possible to install the wireless modem or the PSTN modem on site! ∫ Check the communication mode between the modem and the terminal. If necessary, set the following parameters: Bit rate / bit per second: 9600 baud Number of data bit: 8 bit Parity bit: No parity Stopbit: 1 stopbit These settings can only be changed after connection to the terminal. If a different modem is required or if the quality of the line does not allow to use the set parameters, the settings have to be changed in PC mode. The same applies for all other parameters which can be set previously for modem mode by software. 3.1.1. Initstrings Depending on the provider’s network and the used modem type, it is necessary to adjust the initstring. The following initstrings are factory set: Modem Network Initstring Siemens M1* GSM900 ATE0S7=60S0=2\N6 Siemens M20* GSM900 ATZE0S0=2&S0+IFC=0,0+CBST=7,0,1 Motorola Mobile MR30 “Surf–Pro”** PCS1900 AT*P1&F&K4E0S0=2\N0+CBST=7,0,1 MIKOM MO4000 GSM900/1800 ATE0S7=60S0=2;+CBST=7,0,1 PCMCIA-modem PSTN AT&FE0S0=2 * The Siemens M1 modem is no longer available and is replaced by the Siemens M20. In future, it is assigned to replace all wireless modems working in GSM900/GSM1800 networks by the new MIKOM modem MO4000. **in connection with Cellect2 Card table 3-1 Standard initstrings for modems For further details to the initstrings, please refer to the user’s software manual.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 19 22-Jan-01 3.1.2. PSTN Modem A Hayes compatible PSTN modem can be connected to the control module SM2009. The telephone cable has to be fed through a labeled grommet of the connector panel and must be connected to the designated clamps. For the standard modem type DigiTel 56Euro, use clamps 2 and 3 to connect the telephone lines a and b. Previous standard modems type DigiTel 34P use clamps 1 and 4. In case of failure try both possibilities to check the functionality of the modem connection. figure 3-1 Location of the PSTN Modem ∗ Note: If a PSTN modem is required, the DIP-switches of the Ext. Alarms-switch [4] on the control module has to be set to position OFF “PSTN Modem”. The DIP-switch 2 of the Mode-switch [1] has to be set to position ON “Remote Mode”.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 20 22-Jan-01 3.1.3. Wireless Modem The wireless modem is mounted in the modem box of the lid. figure 3-2 Modem connection on the duplexer Modem connection on the duplexer
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 21 22-Jan-01 3.2. EXTERNAL ALARMS With the external alarms option, it is possible to monitor the status of connected devices via the repeater software, e.g. a UPS. The DIP-switches of the Ext.-Alarms switch on the control module have to be set to position ON “Ext. Alarm 1-4”. ∗ Note: If a PSTN modem is required, only two external alarms are available because the PSTN modem reserves two lines! The connecting clamps are located on the connecting board mounted on the duplexer (BTS side). figure 3-3 Location of external alarm clamps All external alarms are normally high (5V) without connection. Via the software command SET LOGIC, the external alarms can be set to high active (H) or low active (L). Depending on the settings, the external alarms show the status “failure” or “OK” on the display. The configuration for open collector applications is 5V / 0.5 mA. When only 2 external alarms are required, ensure that the other 2 external alarms are set to low active, otherwise the status will always show an alarm. ∗ Note: The name for each external alarm and the name for the alarm message can be defined by the customer with the corresponding software command (see software manual)! ∗ Note: A special software blocking must be removed to use the external alarm option. This can only be carried out by authorized persons from MIKOM.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 22 22-Jan-01 3.3. BATTERY BACKUP The repeater can be provided with the battery backup option to enable alarm calls in case of power failure. The battery backup module supports multiple dial out attempts via modem in case of “System engaged” or other communication problems for about ten minutes under normal environmental conditions. The batteries are protected from deep discharge by use of a low voltage disconnect unit. A local switch is provided to disconnect the battery backup option during maintenance to ensure that all circuits are voltage-free. The switch is located on the battery backup module. The module is directly plugged onto the control module and can be installed on site. During the charging process, a green LED on the module indicates that the battery is charged at the moment. After finishing the process, the LED will be switched off. figure 3-4 Location of the battery backup module Switch LED
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 23 22-Jan-01 4. INSTALLATION 4.1. MECHANICAL INSTALLATION 4.1.1. General F Note: Due to power dissipation the repeater may reach a very high temperature. Therefore, it is necessary to mount the repeater vertically to a wall or a mast without additional enclosure. A clearance distance of one metre above and below the unit should be kept to provide sufficient ventilation. Between the housing and the wall, a minimum distance of 20 mm must be ensured. F Note: The weight of the repeater is approximately 14 kg in standard configuration. Only adequate manpower is allowed to handle the weight of the system. F Note: If it is impossible to mount the repeater with the mounting brackets due to an uneven surface (e.g. a bulged wall in a tunnel), alternative fastening devices may be used. These fastening devices must fulfil the following requirements: F Note: The external strain must not be increased by the alternative fastening devices. Holding devices, which expose the repeater to enhanced vibration or shock due to a greater distance from the wall (leverage) or due to a lower rigidness or stability (vibration), must not be used. F Note: The repeater’s external strain specifications must not be exceeded, particularly the exposure to vibration and shock (please refer to the MIKOM “Environmental and Safety Leaflet” for further detailed information). F Note: Exceeding the specified load limits may cause the loss of warranty!
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 24 22-Jan-01 4.2. WALL MOUNTING PROCEDURE Check the suitability of the wall mounting kit and the wall. ∫ Dismount the mounting brackets which are screwed to the housing with four socket head cap screws M8x16 and two tire bolts. ∫ Use the wall mounting template to mark the position of the drilling holes. Drill four holes and screw the mounting brackets to the wall. ∫ Attach the upper two socket head cap screws M8x16 to the repeater housing. Hang the repeater into the mounting brackets. ∫ Fasten the lower two socket head cap screws M8x16 and the two tire bolts. Ensure that there is free access to the electrical connections as well as to the individual units inside the cabinet while the door of the repeater is open (clearance distance of 1 m is recommended). The approved bending radius of the connected cables must not be exceeded. figure 4-1 Installation drawings of a repeater
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 25 22-Jan-01 4.2.1. Pole Mounting Procedure Standard mounting hardware can not be used to mount the repeater to a pole, a mast or other similar structures. Additional hardware must be used for this type of installation. Such a pole mounting kit could include two threaded rods M8, two U-beams and mounting material like bolts and nuts. figure 4-2 MIKOM pole mounting kits.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 26 22-Jan-01 Dismount the mounting brackets which are screwed to the housing with four socket head cap screws M8x16 and two tire bolts (see figure 4-1 Installation drawings of a repeater). ∫ Fasten the mounting kits and the mounting brackets to the pole or mast. ∫ Attach the upper two socket head cap screws M8x16 to the repeater housing. ∫ Hang the repeater into the mounting brackets. ∫ Fasten the lower two socket head cap screws M8x16 and the two tire bolts. Make sure that there is free access to the electrical connections and to the individual units inside the cabinet while the door of the repeater is open (clearance distance of 1 m is recommended). The allowed bending radius of the connected cables must not be exceeded. F Note: Two Mikom pole mounting kits are required to mount the repeater to a pole or a mast.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 27 22-Jan-01 4.3. ELECTRICAL INSTALLATION 4.3.1. Grounding Grounding must be carried out under all circumstances. An earth bonding cable must be connected to the grounding bolt provided at the outside of the cabinet on the left-hand side. Do not use the grounding screw for connecting external devices. The complete grounding kit is part of the delivery schedule. The complete grounding kit is part of the delivery schedule. figure 4-3 Grounding bolt 4.3.2. Mains Power Supply Before connecting electrical power to the repeater, it must be grounded. The repeater is equipped with a firmly connected mains cable which is fed into the housing through a watertight cable gland. Due to safety reasons, the power supply lead must be protected by fuses. Inside the repeater, the mains cable is connected to a screw terminal on the connecting board. In case the length of the power cable should not be sufficient, it can be replaced by a longer cable.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 28 22-Jan-01 4.3.3. Antennas Connections The repeater has two female antenna connectors 7/16 (or N with adapter). For mounting the corresponding cable connector, we recommend to refer to the corresponding documentation of the respective connector manufacturer. The bending radius of the antenna cables must remain within its specification G0847Z2 figure 4-4 Top view of antenna connections
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 29 22-Jan-01 5. COMMISSIONING 5.1. PREPARATION 5.1.1. General Please read the description carefully to avoid mistakes and proceed step by step as described. The repeater must not be operated with open antenna ports. This means that each antenna port has to be terminated with either a 50Ω resistor, a dummy load or a connected antenna. The repeater could be damaged when operated without any 50Ω terminations. When opening the repeater, do not damage the seals on the devices inside the repeater. Warranty void if the seals are broken! 5.1.2. BCCH-Channel Apart from the antenna isolation measurement described in chapter 5.1.3, it is also necessary to measure the BCCH level (BCCH=Broadcast Control Channel). The resulting max. allowed repeater gain of the antenna isolation must be compared with the resulting max. allowed repeater gain of the measured BCCH channel. The lower gain has to be set for the repeater. The following example clarifies how to set the correct gain: Antenna isolation: Antenna isolation: 100 dB Safety Gain Margin (SGM)*: 15 dB ------------- Allowed max. gain: 85 dB BCCH channel: Power out**: +30 dBm Received level of BCCH: -(-40) dBm ---------------- Allowed max. gain: 70 dB * Refer to chapter 5.1.3 Antenna Isolation for further information about SGM. ** Max. Pout required by customer, but not higher than the rated Pout per channel stated for this repeater at the required number of channels. In this case, 70 dB gain has to be set for the repeater. ∗ Note: If a higher gain is set, the ALC will be active! This might affect the quality of the signal!
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 30 22-Jan-01 5.1.3. Antenna Isolation Before setting the parameters of the repeater, ensure that the antenna isolation is measured and optimized. The Safety-Gain-Margin (SGM) between the antenna isolation and the maximum gain of the repeater is specified to +15 dB for all RF-repeaters, i.e. the gain has to be -15 dB less than the isolation value of the antennas. For better antenna isolation, ICE (Interference Cancellation Equipment) has been developed for channel selective repeaters in the GSM900/1800 networks as well as for PCS1900. ICE is specified for a SGM of –5 dB. Following example will show the significant difference of a repeater with ICE-option compared to a repeater without ICE-option. Assumed case of a poor antenna isolation: • Repeater without ICE Antenna isolation: 80 dB SGM: - 15 dB ------------- Allowed max. gain: 65 dB In this case, the antenna isolation should be improved. The operator has to enlarge the distance between both antennas or has to shield each antenna from the other. Sometimes, it is difficult to enlarge the distance or to shield the antenna to reach the necessary value. The next example clarifies how to solve the antenna isolation problem with an ICE-repeater. The SGM between the antenna isolation and the maximum gain is specified to -5 dB, i.e. the gain can be +5 dB more than the isolation value of the antennas. Assumed case of the same poor antenna isolation as in the previous example: • Repeater with ICE-option Antenna isolation: 80 dB SGM with ICE-option: +5 dB higher ---------------------- Allowed max. gain: 85 dB For further details to ICE or antenna isolation, please refer to MIKOM “Application Note for Antenna Isolation” or “ICE Datasheet”.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 31 22-Jan-01 5.2. BOOT PROCESS As soon as the repeater is switched on, the control module of the repeater starts the boot process; LE3 displays “Power on”. The initialization of the hardware is part of the boot process. The whole process may take up to several minutes. After booting the system, LE1 turns red for a few moments, then flashes green. LE2 also flashes red and then green. This is just an optical functionality test of the two-coloured LEDs. figure 5-1 Control module – Position of LEDs Internal LED LE1 Internal LED LE2 Internal LED LE3 Cause green Power on Software booting Flashes red for a short time Flashes red for a short time green LED test green green green Software boot successful table 5-1 LED indication during boot process LE3 LE2 LE1
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 32 22-Jan-01 5.3. DIP-SWITCHES The configuration of the DIP-switches on the control module is factory set. figure 5-2 Control module – Position of the DIP-switches Mode-switch [1]* Ext. Alarms-switch [4] ON OFF ON OFF 1 Manual Auto 1 Ext. Alarm 4 PSTN (d) 2 Remote Mode Local Mode 2 Ext. Alarm 3 PSTN (c) 3 DO NOT USE! DO NOT USE! 3 Ext. Alarm 2 PSTN (b) 4 DO NOT USE! Auto 4 Ext. Alarm 1 PSTN (a) Switch for additional inputs [2]** MOR/MR-switch [3] ON OFF ON OFF 1 VCC O.C. 1 MR MOR 2 VCC O.C. 2 MR MOR 3 VCC O.C. 3 MR MOR 4 VCC O.C. 4 MR MOR 5 VCC O.C. 5 MOR MR 6 VCC O.C. 6 MOR MR 7 VCC O.C. 7 MOR MR 8 VCC O.C. 8 MOR MR * Switch 1, 3 and 4 are factory set to position Off ** Switch for additional inputs not in use! table 5-2 DIP-switches of control module 1234
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 33 22-Jan-01 5.4. REMOTE SETTINGS After the boot process, the software login is possible. All parameters of the software can be changed by the provider to optimize the repeater according to the network system. There are two possibilities how to login to the software: ∫ locally via a VT100 terminal or a PC with VT100 terminal emulation ∫ remotely via a modem e.g. with the Operations and Maintenance Center (OMC) 5.4.1. Local Login The login via VT100 terminal or a PC with VT100 emulation can only be performed at the repeater. Open the repeater carefully and ensure that DIP-switch 2 of mode-switch [1] is in position OFF. Only when DIP-switch 2 is OFF, a local access to the software on the control module is possible (see chapter 5.3 DIP-Switches). Connect the terminal or PC to the RS232 interface on the control module by means of a standard RS232 interface cable (see picture below). Terminal or PC Control Module SM2009 9 contact SUB-D-connector 9 contact SUB-D-connector male male Pin Pin 123456789897613452 Check the communication mode at the terminal. If necessary, set the following parameters: Bit rate / bit per second: 9600 baud Number of data bit: 8 bit Parity bit: No parity Stopbit: 1 stopbit
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 34 22-Jan-01 ∗ Note: The input is case sensitive, no blanks allowed. The connection will be torn down after three wrong inputs! There are two possibilities to login to the repeater software:  Repeater off: The repeater is switched off, the RS232 interface cable is already connected and the DIP-switch 2 of the mode-switch (1) is set to positon OFF. After switching on the repeater, the boot procedure starts. Subsequently, the display of the terminal shows following report. ----------------------------------------------------------------------------------------------------------------- AT MIKOM REPEATER MRXXX – SM2009 -SW: REP 10XX VX.XX ENTER <.> <CR> TO LOGIN ----------------------------------------------------------------------------------------------------------------- Please type <.> (fullstop) and confirm with <CR> (carriage return) to get to the login orders. ∗ Note: The following step can only be carried out by qualified personnel in consideration of the health and safety warnings. Pay attention not to touch devices while the repeater is operating!  Repeater On: The repeater is operating. After connecting the RS232 interface cable and changing the mode-switch (1) DIP-switch 2 to OFF, the display won´t show a report. Please type <.> (fullstop) and confirm with <CR> (carriage return) to get to the login orders. ∗ Note: Sometimes it is necessary to type the <.> (fullstop)-command twice or three times to get access to the repeater software.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 35 22-Jan-01 After successful login, the USERID is required. ----------------------------------------------------------------------------------------------------------------- ENTER USER ID: ----------------------------------------------------------------------------------------------------------------- Please enter <UserID1>* and confirm with <CR> (carriage return). * UserID1 is factory set and can be changed by software Note case sensitivity and blanks! Now, the correct password is asked. Following order will be displayed on the terminal: ----------------------------------------------------------------------------------------------------------------- ENTER PASSWORD: ----------------------------------------------------------------------------------------------------------------- Please enter <P-word1>** and confirm with <CR> (carriage return). ** P-word1 is factory set and can be changed by software Note case sensitivity and blanks! If the software-login procedure was successful, the input request shown below displays on the terminal: ----------------------------------------------------------------------------------------------------------------- MIKOM > ----------------------------------------------------------------------------------------------------------------- All parameters of the repeater can now be changed to optimize the repeater to the network system. 5.4.2. Remote Login A login e.g. via modem at the OMC enables the operator to set parameters and to query the status of each repeater. This can be done either via a wireless modem or a PSTN-modem. The access commands to the repeater-software are the same as described in chapter 5.4.1 Local Login. If the OMC is used for the remote login, the input “<.> (fullstop) and <CR> (carriage return)” is skipped and UserID and Password are requested right away.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 36 22-Jan-01 For further details to software-login and software-commands, please refer to the user´s software. 5.5. MANUAL SETTINGS Normally, settings are carried out by a VT100 terminal or PC. Additionally, if manual settings are unavoidable, rotary switches on the motherboard enables the operator to optimize the gain and to set the channels. To enable the manual setting of attenuation and channels, ensure that the DIP-switch 1 of the mode switch [1] is in position ON (manual mode). An attenuation of 30 dB max. in steps of 2 dB can be set in the UL- and DL path for channel and band selective repeaters. The channel settings are only available for channel selective repeaters. ∗ Note: While DIP-switch 1 of mode switch (1) is in position ON (manual mode), software settings via VT100 terminal are not possible! Quering the status can still be carried out. figure 5-3 Motherboard Example: Position 0 of the rotary switches S7/S8 equals 0 dB attenuation. Position 1 attenuates the signal by 2 dB, position 8 for instance attenuates by 16 dB. To achieve max. attenuation (30dB), turn the rotary switch of the corresponding path to position F. S4 S5 S6 S7 S8 S9 S1 S2 S3
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 37 22-Jan-01 The following table and the example show how to use the rotary-switches*: Switch Description S1 Channel code x100 S2 Channel code x10 S3 Channel code x1 S4 Channel code x100 S5 Channel code x10 S6 Channel code x1 S7 Attenuation in 2 dB steps upto 30 dB for UL-path S8 Attenuation in 2 dB steps upto 30 dB for DL-path S9 Code switch for motherboard * Factory settings are: S1-S8 in position 0, DIP-switch 1 of mode switch [1] in position “Off” (Automatic mode). Switch S9 can be set to position 0 to 3 depending on the location of the motherboard in the repeater. table 5-3 Rotary switches of the motherboard Example: A gain of 74 dB is required in the UL- and DL-path, module 1 is set to channel 96 and module 2 to channel 113. The repeater has a gain of max. 82 dB. 1. Calculate the difference between the max. repeater gain and the required gain. Max. repeater gain: 82 dB Required gain for UL and DL: 74 dB ------------- Required attenuation for UL and DL: 8 dB 2. Turn switch S7 as well as S8 to position 4 to set an attenuation of 8 dB for UL- and DL-path. 3. Set channel 96 for module 1: Turn switch S1 to position 0: 0 Turn switch S2 to position 9: 90 Turn switch S3 to position 6: 6 -------- Channel: 96 4. Set channel 113 for module 2: Turn switch S4 to position 1: 100 Turn switch S5 to position 1: 10 Turn switch S6 to position 3: 3 -------- Channel: 113
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 38 22-Jan-01 5.6. LEVELLING OF THE REPEATER After software-login, the repeater must be levelled so that the highest output power is achieved without reaching the ALC (Automatic Level Control). ∗ Note: When the local software configuration is finished, don´t forget to switch back DIP-switch 2 of the mode-switch to position ON, otherwise the remote mode via modem will not work!
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 39 22-Jan-01 6. ALARMS 6.1. BITE AND ALARMS The Built-In Test concept comprises the monitoring of the power supplies, the operational currents in the conversion modules, the motherboard and the remote control interface. Furthermore, the synthesizer lock and the temperature of the repeater are monitored. All occurred alarms can be checked via software by typing the “STATUS HIST” command. The provider is then able to acknowledge the alarm manually by the software command “ALARMACKN”, e.g. ALC active, RSSI, door open or stabilty control. If all alarms have been acknowledged, the summary error LEDs are set back to green indication. If monitored via a modem, automatic dialling will generate a summary alarm message. The provider can acknowledge the alarm message and can request a detailed status report. 6.2. HANDLING OF ALARMS As soon as the software recognizes a valid alarm, a message is transmitted to the operator. In remote mode, the alarm can be acknowledged by simply ringing back and typing ALARMACKN. If the reason for the alarm has been cleared or if the alarm should continue, a new alarm message will not be repeated. If there was an interruption of at least one second after acknowledgement, a new alarm message will be generated. 6.3. STATUS REPORT Two instructions enable the operator to get the information of the system status. Typing GET, commands will be responded by a listing of all settings of the repeater. STATUS will be responded by a listing of all individual status information which can be monitored only, but not influenced by SET commands. The complete listing of the syntax with the processor of the control module including the instructions and the messages as well as all available alarms from the system is obtainable as a separate software manual.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 40 22-Jan-01 7. TROUBLE SHOOTING 7.1. ERROR INDICATION • = LED on - = LED off 1. With implemented battery backup module Internal LED LE1 Internal LED LE2 Internal LED LE3 Cause green red green red green - - - - - No power. Check presence of power at the input; replace fuse according to chapter, check battery backup module l l l Indicates a summary failure l l l Mains failure, control module is supplied from battery backup module 2. Without battery backup module Internal LED LE1 Internal LED LE2 Internal LED LE3 Cause green red green red green - - - - - No power. Check presence of power at the input; replace fuse l l l Indicates a summary failure
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 41 22-Jan-01 7.2. BOOT PROCESS Following signals occur during boot process Internal LED LE1 Internal LED LE2 Internal LED LE3 Status green red green red green - - - - l Power on state, Software boot starts l Flashes red short time l Flashes red short time l Software boot starts l l l Software is running The boot process takes about 3 minutes 7.3. ALARM MONITORING WITH THE ALARM HISTORY Check the alarm history. 1. If a hardware module is damaged, replace corresponding hardware module. 2. Minor alarms with no influence on the system can be cancelled by confirming the alarm with the software command ‘alarmackn’, e.g., DOOR OPEN. 3. If all alarms have been acknowledged the summary error LEDs will be set back to green indication. 4. In case of mains power failure the contents of the actual alarm history list will be lost. List with all available alarms in the alarm history. 7.4. POWER SUPPLY Factory set output voltages ( with load ) • 7.8 V ± 0.1 V • 12.4 V ± 0.1 V In case of an I²C-Bus error, also check the power supplies. They must be switched to position ON.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 42 22-Jan-01 7.5. GENERAL REMARKS ∫ After a software download previous user settings ( data default values ) might be overwritten. Before you start a software download save all user settings: - attenuation - ALC threshold - temperature compensation offset ( gain ) - phone numbers etc. ∫ If an ALC alarm occurs during installation or commissioning an user error might be the cause, due to wrong measurements, e.g. ALC: Input level too high à reduce gain
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 43 22-Jan-01 8. MAINTENANCE 8.1. GENERAL ∗ Note The repeater does not require preventative maintenance measures. It is only recommended to replace the RAM/RTC battery and the whole battery backup module after three years usage as a prophylactic measure. The nominal lifetime of these batteries is five years under normal environmental conditions. In the event of a malfunction, it is advantageous to check the status of the antenna systems as well as the continuity of the entire cabling including connectors before replacing the modules. Maintenance on the repeater shall be performed by replacing modules only. Soldering on printed circuit boards shall be avoided. In order to sustain warranty, take care not to damage unintentionally the seals on the modules. To open the housing, the upper screws have to be removed first and than the lower screws (see installation drawing chapter 7.1). Proceed in reverse order to close the housing. The spare parts list, consequently, contains only units which can be replaced without tuning or complex soldering work. Those units are all MIKOM modules as well as internal and external cables. ∗ Note Defect parts should only be replaced by original parts from MIKOM. All interventions inside the housing are at one’s own risk. ∗ Note During maintenance ensure that the repeater has been disconnected from mains and the battery backup module has been switched off.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 44 22-Jan-01 8.2. REPLACEMENT OF THE FUSES The power supply is protected with a primary fuse, type T6.3A / 250V. figure 8-1 Fuse replacement 8.3. REPLACEMENT OF THE MAINS CABLE In case the length of the delivered mains cable should not be sufficient or in case of a defect, the mains cable can be replaced. ∗ Note: Disconnect repeater from mains first! Remove the cover plate with the lock and open the housing by lifting the fixing clamp The mains cable is now accessible from the bottom of the heat sink. Unscrew it from the clamps on the connecting board (see figure 8-2 Connecting board) as well as the small bar fixed with one tallow-drop screw M3. figure 8-2 Connecting board Fuse
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 45 22-Jan-01 Loose the mounting screw of cable gland at the outside of the heat sink (see figure 8-3 Cable gland) and pull the cable through the hole. For mounting a new mains cable proceed in reverse order. ∗ Note The diameter of the power supply lead has to be in the range of 9.5 mm max. and 6.5 mm min. Strip the isolation of the cable to the length of 18 cm and pull it through the cable gland like depicted in 8.4. Inside the housing, use the insulated tube. figure 8-3 Cable gland 8.4. REPLACEMENT OF THE RAM / RTC BATTERY The RAM/RTC battery of the control module has to be replaced in case of memory loss or as a preventive measure after approximately three years usage. The RAM/RTC battery is mounted underneath the battery backup module. It is accessible after opening the housing on the left-hand side in the lid. First remove the whole battery backup module (see chapter 8.5) which is plugged into the control module. By means of a small screwdriver, placed between the battery and the battery socket, the battery can be taken out of the battery socket. The type of the battery is CR 2450 Lithium 3V/500mAh, manufacturer is RENATA. After replacement of the RAM battery, the control module has its basic settings.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 46 22-Jan-01 figure 8-4 Position of RAM/RTC battery ∗ Note Before replacing the battery, disconnect the repeater from mains and take off the battery backup module. ∗ Note Observe the rules for changing Lithium batteries. Wrong connection or treatment may result in bursting of the battery and dissemination of hazardous substances. ∗ Note Don’t try to charge this battery.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 47 22-Jan-01 8.5. REPLACEMENT OF THE BATTERY BACKUP MODULE The battery backup module has to be replaced in case of memory loss or as a preventive measure after approximately three years usage. The nominal lifetime of the accumulator is three years. The battery backup module is accessible after opening the housing on the left-hand side in the lid. It is recommended to replace the whole battery backup module which is plugged into the control module. Before disconnecting the module from the socket, release the three snap-in lockings. The control module has its basic settings after replacement. figure 8-5 Battery backup module Battery Backup Module
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 48 22-Jan-01 8.6. DUPLEXER • On side of the BTS antenna connector: Dismount connecting board first if the duplexer has to be replaced (see chapter 6.11). Dismount the amplifier, mounted on the backside of the duplexer on the side of the DL input, by unscrewing two M2.5 Phillips screws. Take off the amplifier carefully. Pay attention not to damage the three pilot pins. Remove the flat cable to the mother board. Remove the RF cables on the side of the UL output by loosing the SMA connector by means of a torque wrench. Unscrew the four counter sunk screws M3 at the connector panel. Remove the grounding cable. • On side of mobile antenna connector: Dismount the amplifier, mounted on the backside of the duplexer on the side of the UL input, by unscrewing two M2.5 Phillips screws. Take off the amplifier carefully. Pay attention not to damage the three pilot pins. Remove the RF cables on DL output by loosing the SMA connector by means of a torque wrench. Unscrew the four counter sunk screws M3 at the connector panel (see figure 2.2.4-1 Connector panel layout). Remove the grounding screw which is fixed to the extension module with a Phillips screw. 8.7. CONVERSION MODULE Disconnect the SMA connectors by means of a torque wrench to remove the module. Screw off the six hex socket screws by means of a hex socket key. Pull the mounting strap carefully which is fixed on the conversion module and take off the module.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 49 22-Jan-01 8.8. CONTROL MODULE SM 2009 The control module is a Printed Circuit Board and is situated in the lid of the housing. Disconnect the DC cable from power supply. Disconnect flat cable. Remove the modem. Take off the whole control module completely with chassis by unscrewing four nuts M4 or the four knurled screws. For mounting proceed in reverse order. 8.9. POWER SUPPLY ∗ Note Ensure that mains are disconnected and the battery backup module is switched off. The power supply is mounted in the lid of the housing. Open the repeater to get access to the device. Remove all connected cables from the clamps of the power supply. Remove the ground cable. The power supply is fastened to the lid of the housing by means of two nuts M4 on the right-hand side. After loosen the screws, the power supply can be removed. A special key with a mobile element will be required to open these screws. ∗ Note Don’t forget to put heat conducting paste on the mounting side for installation of a new power supply. Use the conducting paste which is included in the spare parts kit.
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 50 22-Jan-01 8.10. CONNECTING BOARD The connecting board is mounted on top of the duplexer on the right-hand side in the heat sink. It is screwed by means of three tallow-drop screws M3. Disconnect the flat cable, mains cable, the cable to power supply and grounding eyelet bolt. figure 8-6 Connecting board
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 51 22-Jan-01 9. APPENDIX 9.1. ELECTRICAL SPECIFICATIONS 9.1.1. Specifications of MR703P Specifications MR703P Frequency range MR703P-ADB MR703P-EFC MR703P-DBEF UL:1850-1885 MHz, DL: 1930-1965 MHz UL:1875-1910 MHz, DL: 1955-1990 MHz UL:1865-1895 MHz, DL: 1945-1975 MHz Bandwidth 0.2-15 MHz, 2.5 dB gain degradation at 200 kHz Gain 70 dB min., K2 dB over frequency and temperature range Gain adjust range 30 dB in 2 dB steps Spurious intermodulation -13 dBm max. Noise figure (@ max. gain) UL and DL 8 dB max. ALC dynamic range 10 dB OICP-3 +44 dBm min. P1dB +34 dBm min. Return loss (@ 25°C amb. temp.) 10 dB min. Power supply 110 Vac, 230 Vac, 24 Vdc or 48 Vdc Power consumption 95 Watt typ. Built in test equipment Current monitor Synthesizer lock monitor Temperature ALC active Alarm forwarding Potential free relay contact and automatic alarm call via RS232 or PCMCIA interface Control functions Gain Center frequency ALC threshold RF connectors 2 x 7/16 female, N as an option *Please contact the MIKOM sales office for further questions to available bandwidths. GSM TDMA CDMA Pout for 1 channel 34 dBm 31 dBm 27 dBm Pout/channel for 2 channels 24 dBm 24 dBm 22 dBm Pout/channel for 4 channels 20 dBm 20 dBm 19 dBm table 9-1 Specification of MR703P All data is subject to change without notice!
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 52 22-Jan-01 9.1.2. Specifications of MR803P Specifications MR803P Frequency range MR803P-TR MR803P-CE UL: 806-824 MHz, DL: 851-869 MHz UL: 824-849 MHz, DL: 869-894 MHz Bandwidth 0.2-25 MHz, 2.5 dB gain degradation at 200 kHz Gain 70 dB min., K2 dB over frequency and temperature range Gain adjust range 30 dB in 2 dB steps Spurious intermodulation -13 dBm max. Noise figure (@ max. gain) UL and DL 8 dB max. ALC dynamic range 10 dB OICP-3 +44 dBm min. P1dB +34 dBm min. Return loss (@ 25°C amb. temp.) 10 dB min. Power supply 110 Vac, 230 Vac, 24 Vdc or 48 Vdc Power consumption 95 Watt typ. Built in test equipment Current monitor Synthesizer lock monitor Temperature ALC active Alarm forwarding Potential free relay contact and automatic alarm call via RS232 or PCMCIA interface Control functions Gain Center frequency ALC threshold RF connectors 2 x 7/16 female, N as an option *Please contact the MIKOM sales office for further questions to available bandwidths. Analog TDMA CDMA Pout for 1 channel 34 dBm 31 dBm 27 dBm Pout/channel for 2 channels 24 dBm 24 dBm 22 dBm Pout/channel for 4 channels 20 dBm 20 dBm 19 dBm table 9-2 Specification of MR803P All data is subject to change without notice!
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 53 22-Jan-01 9.2. MECHANICAL SPECIFICATION Standard cabinet: Max. Height x Width x Depth: 445 x 255 x 167*/185 mm (Main Unit) *without mounting brackets Volume: < 14 litres Weight: approximately 14 kg per unit, standard configuration 9.3. ENVIRONMENTAL AND SAFETY SPECIFICATIONS For detailed information, refer to the environmental and safety specification leaflet for MIKOM indoor/outdoor cell enhancers, related to ETS 300 019 (European Telecommunication Standard). Operating temperature: • Normal temperature range: +5°C...+40°C • Extreme temperature range: -33°C +50°C Humidity: 90% @ +30°C
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 54 22-Jan-01 9.4. SPARE PARTS LISTS The following lists contain all parts available for the MRx03P. The configuration of the delivered unit meets the requirements of the customer and can differ depending on the state of the delivery. 9.4.1. Spare Parts List of MR703P Repeater: Repeater Id.-No.: MR703P-ADB: 154856 --- --- MR703P-EFC: --- 154861 --- MR703P-DBEF: --- --- 154862 Id.-Nos.: Designation: MR703P ADB MR703P EFC MR703P DBEF PCS-Duplexer UL 144382 144384 151072 PCS-Duplexer DL 144381 144383 151073 Basic Module var. 15 MHz 151463 Final Amplifier 4 Watt 154737 Power supply, no plug, 185-320 Vac 148812 Power Supply, no plug, 230 Vac ±15% 144306 Power Supply, USA plug, 115 Vac ±15% 141230 Power Supply, no plug, 80-130 Vdc 145524 Power Supply, no plug, 36-72 Vdc 144946 Power Supply, no plug, 18-43 Vdc 145504 MO4000 Kit 154633 I2C-Board 153144 Modem Kit PSTN 143112 Ext. Alarms SW-Option 145067 2 Ext. Alarms + PSTN 148272 Battery Backup Module 143052 SW MOB100 V1.10 143055 SW REP1009 V1.11 147127 Mother Board 148968 Connecting Board 142362 Control Unit SM4000 151957 Control Unit SM2009 143051 table 9-3 Spare parts list of MR703P Mikom reserves the right to replace the spare parts listed above by equivalent substitutes!
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 55 22-Jan-01 9.4.2. Spare Parts list of MR803P Repeater: Repeater Id.-No.: MR803P-CE: 806-824 MHz;851-869 MHz --- 155340 MR803P-CE: 824-849 MHz;869-894 MHz 155215 -- Id.-Nos.: Designation: MR803P-CE MR803P-TR PCS-Duplexer UL 148334 148333 PCS-Duplexer DL 148335 148336 Basic Module var. 15 MHz 151976 150150 Final Amplifier 4 Watt 155191 Power Supply, no plug, 185-320 Vac 148812 Power Supply, no plug, 230 Vac ±15% 144306 Power Supply, USA plug, 115 Vac ±15% 141230 Power Supply, no plug, 80-130 Vdc 145524 Power Supply, no plug, 36-72 Vdc 144946 Power Supply, no plug, 18-43 Vdc 145504 MO4000 Kit 154633 I2C-Board 153144 Modem Kit PSTN 143112 Ext. Alarms SW-Option 145067 2 Ext. Alarms + PSTN 148272 Battery Backup Module 143052 SW MOB100 V1.10 143055 SW REP1009 V1.11 147127 Mother Board 148968 Connecting Board 142362 Control Unit SM4000 151957 Control Unit SM2009 143051 table 9-4 Spare parts list of MR803P Mikom reserves the right to replace the spare parts listed above by equivalent substitutes!
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 56 22-Jan-01 9.5. INSTALLATION DRAWING OF THE REPEATER figure 9-1 Installation drawing of MRx03P
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 57 22-Jan-01 9.6. LAYOUT OF THE REPEATER LID figure 9-2 Repeater lid Mains Switch Door Contact Power Supply Repeater Lid Control Module RAM/RTC battery
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 58 22-Jan-01 9.7. LAYOUT OF THE REPEATER HEAT SINK figure 9-3 Repeater heat sink Heat sink Final Amplifier Conversion Module Duplexer Connector Panel Connecting Board Modem Connector
USER´S MANUAL FOR BAND SELECTIVE REPEATERS MRX03P User'sManual.doc Id.-No.:154999 Page 59 22-Jan-01 10. INDEX A Abbreviations................................................ 7 Address of MIKOM........................................ 9 Alarm BITE and Alarms..................................... 39 Handling of............................................. 39 Status Report.......................................... 39 Alarm history............................................... 41 Antenna connections................................... 28 B Battery Backup............................................ 22 Battery backup module Replacement of ...................................... 47 Boot process......................................... 31, 41 C Commissioning ........................................... 29 Communication mode parameters............... 18 Control Module............................................ 15 Conversion Module..................................... 13 D DIP-switches............................................... 32 Duplexer..................................................... 12 E External alarms........................................... 21 F Final Amplifier............................................. 14 G Grounding................................................... 27 H Health and Safety Warnings.......................... 8 I Initstrings .................................................... 18 Installation Electrical................................................. 27 Mechanical ............................................. 23 L List.............................................................. 10 Local Login ................................................. 33 M Mains power supply .................................... 27 Maintenance............................................... 43 Manual settings........................................... 36 Measurements Antenna isolation .................................... 30 BCCH-Channel....................................... 29 Levelling ................................................. 38 Measuring Aids........................................... 12 Modem (general)......................................... 18 Motherboard ............................................... 16 Mounting Pole........................................................ 25 Wall ........................................................ 24 Mounting brackets....................................... 24 P Power supply Replacement of....................................... 49 Power Supply.............................................. 17 Preamble...................................................... 9 PSTN modem ............................................. 19 R Remote Login ............................................. 35 Remote Settings ......................................... 33 Repeater Installation Drawing.................................56 Layout of Heat Sink.................................58 Layout of Lid........................................... 57 Repeater design.......................................... 11 Replacement of Battery Backup Module........................... 47 Connecting Board................................... 50 Control Module SM2009 ......................... 49 Conversion Module.................................48 Duplexer................................................. 48 Fuses ..................................................... 44 General................................................... 43 Mains Cable............................................ 44 Power Supply ......................................... 49 RAM / RTC Battery.................................45 Rotary Switches on Motherboard................. 36 S Spare parts lists .......................................... 54 Specifications Electrical................................................. 51 Mechanical ............................................. 53 T Table of Contents.......................................... 3 Troubleshooting Alarm Monitoring..................................... 41 Boot Process .......................................... 41 Error Indication ....................................... 40 General Remarks.................................... 42 Power Supply ......................................... 41 W Wireless modem......................................... 20

Navigation menu