Anfair Electronics Plastic Factory MBTK35 Bluetooth Receiver Kit User Manual NS MBTK35 16 0391 QSG V1 ENG FINAL ai

Anfair Electronics Plastic Factory Bluetooth Receiver Kit NS MBTK35 16 0391 QSG V1 ENG FINAL ai

Users Manual

PACKAGE CONTENTS• Bluetooth receiver• 3.5 mm audio cable (3 ft.)• 3.5 mm male-to-male adapter• 3.5 mm to RCA adapter• Velcro mounting pads• Micros USB charging cable• Carrying pouch• Quick Setup Guide FEATURES Before using your new product, please read these instructions to prevent any damage.QUICK SETUP GUIDE NS-MBTK35/NS-MBTK35-C1 Reverse/Volume down 2 Multi-function button (MFB): Power on/o, pairing, play, pause, call3 Skip/Volume up 4 LED indicator5 Micro USB charging port 6 Audio jack7 MicrophoneCHARGING THE RECEIVERFully charge the Bluetooth receiver before you use it for the rst time. When the red LED starts to blink during use, it indicates the battery is low and requires charging.1 Plug the micro USB plug of the USB cable into the micro USB port on your Bluetooth receiver.2 Plug the USB end of the cable into an active USB port, or any USB charger. A steady red LED indicates it is charging.3 Disconnect the receiver from the USB cable when the red LED indicator turns o. It may take up to three hours to fully charge.USING BLUETOOTHTo get started, you need to pair the Bluetooth receiver with your phone or device.1 With the receiver turned o, press and hold the MFB for seven seconds. The LED ashes and the receiver enters pairing mode.2 Activate the phone’s Bluetooth function and search for your receiver. Click on the product name “NS-MBTK35” to connect. See the instructions that came with your Bluetooth device for information about pairing.3 If you are asked for a password, enter “0000”. When pairing is complete, the LED lights solid blue and a tone sounds.RECONNECTING TO A PAIRED DEVICE1 Every time the receiver is turned on, it will connect to the last connected device automatically. If you want to pair with another device, turn o the Bluetooth function of the connected device, and repeat the pairing procedure above for the new device.2 If a device does not automatically reconnect, you may need to reselect NS-MBTK35 on your Bluetooth device.3 If the receiver is not paired to a Bluetooth device for three minutes, it will turn o automatically. USING YOUR RECEIVER1 Press and hold the MFB for two seconds to turn on your receiver. The LED lights solid blue when it is connected to your Bluetooth device.2 When the receiver is turned on, press and hold the MFB for two seconds to turn o the receiver. LISTENING TO MUSIC1 To play/pause audio, press the MFB once.2 To increase the volume, press once.3 To reduce the volume, press once.4 To skip to next track, press and hold .5 To skip to previous track, press and hold .MAKING PHONE CALL1 To make a call, use your phone’s controls, then select the receiver as the audio source.2 To answer an incoming call, press the MFB .3 To reject an incoming call, press and hold the MFB . 4 To end a call, press the MFB once.Right LeftBottom FrontPortable Bluetooth® Audio ReceiverNS-MBTK35_16-0391_QSG_V1_ENG_FINAL.ai 1 7/14/2016 9:49:17 PMNS-MBTK35_16-0391_QSG_V1_ENG_FINAL.ai 1 7/14/2016 9:49:17 PMV1FINALFOR PRINT
AUXEnglish V1 16-03911 2 3 4 5 6FCC Statement:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user isencouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Caution: Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.Industry Canada ComplianceIC StatementThis device complies with Industry Canada’s licence-exempt RSSs.Operation is subject to the following two conditions:(1) This device may not cause interference; and(2) This device must accept any interference, including interferencethat may cause undesired operation of the device.Conformité à Industrie CanadaDéclaration d'ICLe présent appareil est conforme aux CNR d'Industrie Canadaapplicables aux appareils radio exempts de licence. L'exploitationest autorisée aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et(2) l'utilisateur de l'appareil doit accepter tout brouillageradioélectrique subi, même si le brouillage est susceptible d'encompromettre le fonctionnement.AUXUSING YOUR WIRED HEADPHONE OR EARPHONE,RECEIVER WITH STEREO OR RECEIVER IN THE CARTROUBLESHOOTINGPROBLEMNo sound or low volumeCannot connect with BluetoothBluetooth device keeps unpairing“NS-MBTK35” does not appear on my Bluetooth deviceNo powerSOLUTION• Turn up the volume on your receiver and Bluetooth device. • Make sure that your Bluetooth device is not muted. • Make sure that your receiver and Bluetooth device are not paired to other devices.• Make sure that your Bluetooth device is turned on, Bluetooth is turned on, and “NS-MBTK35” is selected.• Shorten the distance between your receiver and the Bluetooth device. • Turn your devices o, then on. Re-pair your receiver and Bluetooth device. • Make sure that your receiver and Bluetooth device are not paired to other devices. • Make sure that your Bluetooth device supports the HSP, HFP, A2DP, or AVRCP Bluetooth protocol. • Shorten the distance between your receiver and your Bluetooth device. • Recharge your receiver and the Bluetooth device's batteries.• Shorten the distance between your receiver and the Bluetooth device. • Put your receiver into pairing mode, then refresh your list of Bluetooth devices. For more information, see the documentation that came with your Bluetooth device.• Make sure that your Bluetooth receiver is charged. • Make sure that your Bluetooth receiver is turned ON.La operación de este equipo está sujeta a las siguientes dos condiciones:1) es posible que este equipo o dispositivo no cause interferencia perjudicial y2) este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su propia operación no deseada.ONEYEAR LIMITED WARRANTYVisit www.insigniaproducts.com for details.CONTACT INSIGNIA:For customer service, call 877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)www.insigniaproducts.comINSIGNIA is a trademark of Best Buy and its aliated companies. Registered in some countries. Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richeld, MN 55423 U.S.A.©2016 Best Buy. All rights reserved. Made in ChinaOR3.5mm audio cable3.5mm audio cable3.5mm audio cableattached to headphonesSourceReceiverUsing your smartphone as the audio source, you can connect a variety of sound devices through your Bluetooth receiver, such as headphones, a stereo receiver, or a car audio system.3.5mm audio jackNS-MBTK35_16-0391_QSG_V1_ENG_FINAL.ai 2 7/14/2016 9:49:18 PMNS-MBTK35_16-0391_QSG_V1_ENG_FINAL.ai 2 7/14/2016 9:49:18 PM

Navigation menu