Ansen Electronics Co 0790-4TX Driveway Patrol(TX) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1473666
Application ID	SxRyxkeZFaB3z32Y+1DJww==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	57.03kB (712906 bits)
Date Submitted	2011-05-27 00:00:00
Date Available	2011-05-27 00:00:00
Creation Date	2007-11-14 15:32:29
Producing Software	Adobe PDF library 6.66
Document Lastmod	2011-05-13 13:50:53
Document Title	User Manual
Document Creator	Illustrator

Driveway Patrol
Instructions
Congratulations on purchasing the Driveway Patrol! Your set comes with a volume controlled Chime Unit
and a Passive Infra-Red (PIR) Sensor. Both are battery operated. The Driveway Patrol system is simple to
install and requires no wiring.
Installing the Batteries:
1. The chime requires three C-size batteries (not included). To install the chime unit’s batteries, slide off
compartment cover in direction of arrow and then install the receiver’s batteries. Be sure to observe
correct polarity (+ and -) as marked inside the battery compartment.
2. The PIR sensor requires a 9V battery. To install the PIR sensor’s battery, unscrew the back cover of
the sensor and insert the battery. Be sure to observe correct polarity (+ and -) as marked on the battery
compartment.
Operation:
1. Your Driveway Patrol Receiver Chime Unit has 3 settings (Hi or Lo Volume and Off). To switch the unit
ON, select Hi or Lo Volume Settings.
2. Hang the PIR (Passive Infra Red) Sensor Unit at the entrance of your driveway (such as on a mailbox,
on a tree or on a ground stake). You may also place the PIR Sensor on your garage, near the front
entrance or rear door. Any movement nearby will transmit a signal to the Receiver Chime Unit triggering
it to signal the chime.
3. Please ensure to place the PIR Sensor at least three feet high above the ground.
4. Receiver must be used indoors.
Important Note:
A) Whenever installing the PIR sensor the first time, the red LED on the PIR sensor may illuminate for about
60 seconds. To avoid receiving false alert, the door chime should be turned on after the first 60 seconds
of the PIR sensor installation.
B) In some applications the motion detector may be too sensitive, resulting in false alerts. To remedy this
situation, put masking tape or labels on each side of the sensor window. Start on the sides and add an
equal length of masking tape or labels to each side. Test the detector and add more covering if needed.
Keep the band as narrow as 1/8” wide or wider depending on individual situation. Some trial and error
may be required to find the optimal width.
Specifications:
Transmission Range; 400 feet (open area)
Transmission frequency; 434MHz
PIR sensor range: 20˚ X 30 feet
Battery Caution:
Receiver: 3 X 1.5V “C-size” battery, not included
Transmitter: 1 X 9V battery, not included
FCC Part 15 compliance
1. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
2. Non-rechargeable batteries are not to be recharged.
3. Never mix old and new batteries.
4. Make sure batteries are inserted with correct polarity.
5. Exhausted or dead batteries are to be removed from the unit.
- Consult the dealer or an experienced radio/TV technician for help.
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCECAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE
EQUIPMENT.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
About                           : uuid:6267caf6-8cf8-43ca-b74d-dc4db7d407cb
Modify Date                     : 2011:05:13 13:50:53+08:00
Create Date                     : 2007:11:14 15:32:29+08:00
Metadata Date                   : 2011:05:13 13:50:53+08:00
Creator Tool                    : Illustrator
Document ID                     : uuid:4018c1d0-9538-469e-8207-6115be006c7f
Instance ID                     : uuid:ffaaea56-dd48-4edc-8a88-e3add57e4f33
Format                          : application/pdf
Producer                        : Adobe PDF library 6.66
Has XFA                         : No
Page Count                      : 2
Creator                         : Adobe Illustrator(R) 11.0
For                             : design_dept, Design
Title                           : 89-20790-103_revised.pdf
Bounding Box                    : 14 6 348 477
Creator Version                 : 14
Container Version               : 11
Image Height                    : 471
Image Width                     : 334
Image Size                      : 334x471
Megapixels                      : 0.157

EXIF Metadata provided by EXIF.tools