Ansen Electronics Co D009TX Wireless Doorbell User Manual Print 76610
Ansen Electronics Co Wireless Doorbell Print 76610
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 510909 |
| Application ID | GMpVb0mmAjiZFG7SUU05RQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 19.61kB (245102 bits) |
| Date Submitted | 2005-01-31 00:00:00 |
| Date Available | 2005-01-31 00:00:00 |
| Creation Date | 2004-12-31 15:53:53 |
| Producing Software | Acrobat Distiller 6.0.1 for Macintosh |
| Document Lastmod | 2005-01-07 19:14:00 |
| Document Title | Print 76610 |
| Document Creator | QuarkXPress: pictwpstops filter 1.0 |
| Document Author: | Amy |
76610_1 12/31/04 3:53 PM Page 1 D009 Battery Operated Wireless Door Chime Doorbell Button Installation Instructions Installation (For wireless only operation) • Determine where you want to mount the doorbell button. Do not mount on or near a metal surface. NOTE: If doorbell button must be mounted on a metal surface, insert a wooden shim (at least 1/2” thick) behind doorbell button to elevate it above metal surface. • Remove doorbell button cover by inserting a small screwdriver into the slot at the bottom of the doorbell button and twisting slightly. (Figure 1) • Locate doorbell button base on surface and mount with #6 screws (and plastic anchors, if needed). Mounting hardware is included. • Install battery, observing polarity (+/-). • Replace cover by aligning locks and snapping into place. Doorbell Button (Transmitter) Installation (For combination wired and wireless operation) • Doorbell button will activate the wireless chime in this package and your existing wired chime simultaneously. • Determine where you want to mount the Doorbell button. For satisfactory wireless operation, do not mount on or near a metal surface. NOTE: If Doorbell button must be mounted on a metal surface, insert wooden shim (at least 1/2” thick) behind Doorbell button to elevate it above metal surface. • Remove cover of existing Doorbell button, disconnect wires and remove Doorbell button base. • Remove new Doorbell button’s cover by inserting a small screwdriver into the slot at the bottom of the Doorbell button and twisting slightly. (Figure 1) • Pass existing wires through small holes in Doorbell button base. • Attach wires to terminals (posts) on Doorbell button circuit board (Figure 2). Thread a short length of bare copper into the hole in one terminal. Secure with screw atop terminal. Repeat with remaining wire. Attach either wire to either terminal. • Position Doorbell button base onto surface and mount with #6 screws (and plastic anchors, if needed.) Mounting hardware is included. • Install battery, observing polarity (+/-). • Replace cover by aligning locks and snapping into place. Figure 1 Figure 2 Figure 3 Operation After battery is installed, push button and adjust volume setting on chime(s). Changing Channels Channels should be changed from original factory setting ONLY if you are experiencing interference from other electronic or wireless devices. To change channel, simply slide one or more dip switches in the doorbell button and the chime to a new position. • Ten dip switches are located in the Doorbell button (transmitter) and eight dip switches in the Chime (receiver). (Figure 3) • Perform this procedure on both. Take care to place the switches in the same position on both Doorbell button and Chime. • To access the channel adjustments on the doorbell button, remove the cover of the doorbell button by depressing the small latch at the bottom (Figure 1.) Find the dip switches inside and change the position of one or more of the switches numbered 1 through 7. • To access the channel adjustments on the chime, use a small cross-point screwdriver to remove the cover on the back of the chime. Place switches 1 through 7 in exactly the same positions as you did on the doorbell button. (Figure 3) • With battery in place, press the doorbell button to confirm both units are set the same. After the chime rings, replace the covers of both doorbell button and chime. Changing Tone Setting Your new chime has both Westminster and Ding Dong tones. Tone selection is done in the Doorbell button (this allows you to differentiate between entrances). • To change to the other tone, remove the cover of the doorbell button (Figure 1), and reverse the positions of Dip switches 9 and 10 (Figure 2). Troubleshooting Problem: Solutions: Chime does not ring. Verify chime volume switch is set to Hi or Lo. Check polarity of battery in doorbell button. Replace battery in doorbell button. Verify that doorbell button and chime are set to the same channels. Check polarity of batteries in chime. Replace batteries in chime. Check if either unit is near a metal surface. If so, move or at least insert a wooden shim a minimum of 1/2 inch thick between unit and metal surface. Move chime to a different location still within 150 ft. of doorbell button. Problem: Solution: Ring is too loud or too quiet. Adjust volume setting on chime. Problem: Solution: Chime rings without pressing doorbell button. Change channel in both Chime and Doorbell button. (See “Changing Channels” above.) Problem: Solution: Chime is dirty. Remove dust with a vacuum and soft brush. Clean with damp cloth and mild, non-abrasive household liquid. Do not spray liquid directly into chime. Chime may be painted; however, blocking the sound slots will mute the tone. NOTE: If your chime still does not function, then return this chime, along with proof of purchase (to verify warranty) to our facility for repair or replacement at our discretion. See warranty for additional information and our address. Please do not return this device to your retailer. © 2004 WESTINGHOUSE LIGHTING CORP.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 2 Profile CMM Type : Lino Profile Version : 2.1.0 Profile Class : Display Device Profile Color Space Data : RGB Profile Connection Space : XYZ Profile Date Time : 1998:02:09 06:49:00 Profile File Signature : acsp Primary Platform : Microsoft Corporation CMM Flags : Not Embedded, Independent Device Manufacturer : IEC Device Model : sRGB Device Attributes : Reflective, Glossy, Positive, Color Rendering Intent : Perceptual Connection Space Illuminant : 0.9642 1 0.82491 Profile Creator : HP Profile ID : 0 Profile Copyright : Copyright (c) 1998 Hewlett-Packard Company Profile Description : sRGB IEC61966-2.1 Media White Point : 0.95045 1 1.08905 Media Black Point : 0 0 0 Red Matrix Column : 0.43607 0.22249 0.01392 Green Matrix Column : 0.38515 0.71687 0.09708 Blue Matrix Column : 0.14307 0.06061 0.7141 Device Mfg Desc : IEC http://www.iec.ch Device Model Desc : IEC 61966-2.1 Default RGB colour space - sRGB Viewing Cond Desc : Reference Viewing Condition in IEC61966-2.1 Viewing Cond Illuminant : 19.6445 20.3718 16.8089 Viewing Cond Surround : 3.92889 4.07439 3.36179 Viewing Cond Illuminant Type : D50 Luminance : 76.03647 80 87.12462 Measurement Observer : CIE 1931 Measurement Backing : 0 0 0 Measurement Geometry : Unknown Measurement Flare : 0.999% Measurement Illuminant : D65 Technology : Cathode Ray Tube Display Red Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Green Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Blue Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Application Record Version : 2 Caption-Abstract : 0784-5 eng im By-line : amy Object Name : 0784-5 eng im IPTC Digest : 224c76d3ab616e5d322187e790c6e5f9 X Resolution : 150 Displayed Units X : inches Y Resolution : 150 Displayed Units Y : inches Print Style : Centered Print Position : 0 0 Print Scale : 1 Global Angle : 30 Global Altitude : 30 Copyright Flag : False URL List : Slices Group Name : (NEW) Num Slices : 1 Pixel Aspect Ratio : 1 Photoshop Thumbnail : (Binary data 2844 bytes, use -b option to extract) Has Real Merged Data : Yes Writer Name : Adobe Photoshop Reader Name : Adobe Photoshop CS Exif Byte Order : Big-endian (Motorola, MM) Image Description : 0784-5 eng im Orientation : Horizontal (normal) Resolution Unit : inches Software : Adobe Photoshop CS Macintosh Modify Date : 2005:01:07 19:00:57 Artist : amy Color Space : sRGB Exif Image Width : 827 Exif Image Height : 1181 Compression : JPEG (old-style) Thumbnail Offset : 342 Thumbnail Length : 0 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:3b4204b2-609d-11d9-837f-000d93b00e9a Producer : Acrobat Distiller 6.0.1 for Macintosh Create Date : 2004:12:31 15:53:53+08:00 Creator Tool : QuarkXPress: pictwpstops filter 1.0 Metadata Date : 2005:01:07 19:14:00+08:00 Document ID : uuid:23aadfb8-5b01-11d9-ba83-000a95a522d2 Format : application/pdf Creator : Amy Title : Print 76610 Author : AmyEXIF Metadata provided by EXIF.tools