Apex Toys GD-90A ELF B User Manual GD 90A 20171013

Apex Toys (Shenzhen)Co., Ltd. ELF B GD 90A 20171013

15_GD-90A UserMan

IMPORTANT Insert the battery into the quadcopter and connect the plug. The two indicators will begin flashing. Place the quadcopter on a flat surface.Important: Be sure the surface is flat and level. The quadcopter needs to calibrate it’s orientation.PLEASE PRACTICE SIMULATED FLIGHT BEFORE ACTUAL FLYING Before you are familiar with the unit, please don't pilot it . Read the instruction carefully to get familiar with the direction controls.1. Checking that propellers are securely attached to the motors. Pull the throttle down to prevent takeoff.2. Place quadcopter in a clear open field and point the tail towards yourself.3. Practice operating the control sticks (as shown below), and repeat practicing “Throttle high/low”, “ Left/right ”, “Forward/backward”, and “bank left/right”.4.Strong impacts can jam the motors, using a long flat nose plier to unjam to rotor.5.The simulation flight practice is very important, please keep practicing until you are comfortable with the controls.After turn on the quadcopterthe LED indicators keepflashing but the quadcopterdoes not respond.Transmitter and receiverfail pairing• Sync the remote controland copter (refer to P.7)• Fully charge the battery 1.The blade isn’t fully installed2.Rotor blade deformation3.Rotor blade not match code• Change blade• Correct the level refer to P6• Replace the main wing • Replace the main motorThe quadcopter still keepsturning after trimming therudder trim, or inconsistentspeed during left/right turns.1. This product is only suitable for users overthe age of 8. Piloting this quadcopter will be dificult at the beginning. We recommend be occampanied by an experienced pilot at first.2. This product is designed with high-tech electronics and mechanical parts. Do not fly near people. Improper operation can result in injury or property damage. We will not accept any responsibility for this.3. We will not take any responsibilty for accidents during the operation of this device.4. Contact cutomer service for help if you have any problems with the device. 1.Checking the surroundings before flying.2.Do not let the plane fly out of sight when flying.3.Do not let the child play alone, play together with adult.4.Please make sure, there is no other player use the same frequency at the same area.Do not fly in these areas.Cautions: QUADCOPTER COMPONENTSPACKAGE CONTENTS REMOTE CONTROL FUNCTIONSThe propeller system is a precision instrument that may need to be repaired or replaceed from time to time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to propeller blades.1.The aircraft has four blades, two white colors on front, and two black colors on back (see the diagram below).2.When replacing the propeller blades, make sure to match both the color of the blade and the indication letter on the blade.3.Replace broken blades with the correct blade. Charge with our dedicated charger.RECHARGEABLE BATTERY:This Quadcopter uses a Li-Poly rechargeable battery.If battery no longer stays charged,dispose of battery properly according to local disposal requirements.CONTROLLER BATTERIES:Remote control requires 2”AAA”batteries (not included).Please read the important battery safety warning below.●Do not mix alkaline,standard (carbon-zinc) and rechargeable betteries (Nickel Metal Hydride).●Do not mix old and new batteries.●Non-rechargeable batteries are not to be recharged.●Rechargeble batteries are to be removed from the item before being charged (if removable).●Rechargeble batteries are only to be charged under adult supervision.●Exhausted batteries should be removed immediately and must be recycled or disposed of properly according to state or local government ordinances and reulations.●The supply terminals are not to be short-circuited.●Only batteries of the same or equivalent type as recommended are to be used.●Batteries are to be inserted with the correct polarity (see inside booklet for diagram).●Do not dispose batteries in a fire-batteries may leak or explode.BATTERY WARNINGSThe LED will be on continuously while the quadcopter is on. When it is low on power the indicator will blink. Please land the quadcopter.SYNCING THE REMOTE CONTROL & QUADCOPTERSTEP 13.7V 350mAhLi-Po BatterySTEP 2FLIGHT ADJUSTMENT AND SETTING TROUBLE SHOOTING DURING FLIGHT SolutionNo response after thebattery is connected tothe quadcopter.Main rotor continues to spin after landingHelicopter rotor spins butunable to take off.The helicopter still keepsturning after rudder trimingor inconsistent speed duringleft/right pirouette.1. The blades haven’t been installed in the right place.2. Rotor blade deformation3. Didn’t calibrate the flight.1. Replace the main wingReplace the main motor2. Change blade3. Correct the level refer to P6Throttle stick not on thelowest position1.Check whether the bladeassembled correctly or not.2.Helicopter battery depleted.Make sure the Throttle stick ison the lowest positionCheck whether it is low power Charging the helicopterThe quadcopter shifts forwards/ backwards.The trim is not even. • Trim the elevator back to center.• Restart the remote control.1.Rotor blade turns off2.Rotor blade deformation1.Change replacement rotors2.Tighten the RotorsCan not fly the helicopter after crashingQUADCOPTER COMPONENTSFLIGHT CHARGING CONTROLLER INSTRUCTIONCAUTIONS FLIGHT ADJUSTMENT AND SETTINGSSYNCING THE REMOTE CONTROLAND THE QUADCOPTER REPLACING THE PROPELLER BLADE GD-90AHigh-voltage power lines Rainstorm and thunderstormNear the railway Roads and nearby places Forests and rivers High windsThe places of CrowdscontrollerBattery chargeStunt SpeedHeadless modeThe direction rockerThe throttle rockerFront and back fine-tuningLeft and right fine-tuningOn/off buttonOne key to return backOne key to take offOne key to landAs shown in th e figure , push the roc ker of the rem ote control to the po sit ion i n the lower ri ght c orn er at t he same time. A t this time th e ind ica tor lig ht of the airc raf t fla she s and then loo sen s the remote c ont rol, and the indic ato r light is alw ays on an d the c alibrati on is c omp lete.WARNING When not in us e for a l ong time, pl ease take out the rem otecontrol batte r y and kee p it pr operly.Note: If the rem ote c ontrol bat ter y i s not rem oved, t he lo ng stora ge wi ll ca use the leak age of the bat ter y a nd dama ge the remote c ont rol dev ice .1.On/off(1)On(After put on the battery, R/C is in sleep model,indicator extinguish when off)Short Press the ON/OFF, the remote control enters the normal mode of work, the buzzer is short sound one beeping, and the power indicator is fading.(2)Power off: long press the ON/OFF, the buzzer is short sound two beeping, the power indicator is out and the remote control is off.2.TurningWhen the remote control and the aircraft are pairing the code, move the turning rocker to left and right,the aircraft will turn left and right.3.Forward and backwardWhen the remote control and the aircraft are pairing the code, move the rocker to forward and backward, the aircraft will fly forward and backward.4.Left and rightWhen the remote control and the aircraft are pairing the code, move the rocker to left and right,the aircraft will fly left and right.5.Fine-tuning functionThe aircraft can be stabilized by adjusting the direction of the aircraft, in the opposite direction of flight.6.Headless modeShort press the button to enter headless mode. The vehicle’s flying direction will be the same as the demand of controller,no matter where the head is .7.StuntLong press the button for stunt .The beeper will keep. ringing.8.SpeedShort press the button to adjust the speed. There are three speed levels.You will hear a beep sound while adjusting . Beep one for level 1 ,beep two for level 2, beep three for level 3. The higher the level ,the faster the speed.9.One key take off and one key landingIn the fixed high mode,after press the one key take off and one key landing buttons, automatically aircraft up to one meter from the ground level hover, trigger buttons again, aircraft flying will fall to the ground stops automatically10.One key to returnShort press the button for one key to return . Press again to finish return .11.Calibration(1) if the aircraft is drifting to one side during takeoff, it can be calibrated to make the flight more stable(2)calibration method: the aircraft is placed on the horizontal surface, and the two rocker of the remote control is pushed to the lower right corner, when observed the indicator light flashes on the aircraft, release the remote control rocker, indicating that it has been calibrated.(note: the aircraft should be kept at the horizontal surface. During calibration, the aircraft will not be able to riot . After the calibration is completed, the indicator light will stop flash quickly).12：Low voltage warning:When the battery is lower than 2.5V of the remote control， the power light will flicker and alarm prompt to change the battery. when the aircraft into the low voltage alarm, the buzzer will send a didi alarm of the remote control , indicating that the aircraft needs to stop flying Caution During the flight, the indicator light of the aircraft is slow to flash while the remote control makes a "beep beep", indicating that the battery voltage is insufficient and please land down to recharge the battery.Mobile phone adapter：Output: 5VCharging current: 1-2A.1.Take off the battery from the vehicle. Connect the battery with a USB cable . Plug the USB cable into a mobile phone adapter or a computer.2.The Charging Indicator will blink when charging. The Charging Indicator will turn OFF when fully charged .CAUTION CAUTION FLIGHT ADJUSTMENT AND NOTICE FOR BEGINNERS Check if the screws and blades are firmly tightened Check if the transmitter and helicopter are fully charged. Make sure that no people or obstructions are in the vicinity. You must first practice hovering to fly safely, this is a basic flight action(meaning keep the helicopter in mid air in a fixed position) Please stand approximately 6ft diagonally behind the helicopter. 1. The throttle is on the left hand, push the throttle a little up to raise the copter to your line of sight then pull down a little to let the quadcopter slowly down to the floor. Repeat until you can easily and quickly control the altitude. 2.Hovering flight practic: Raise the quadcopter to a certain height then hover at that altitude.3.Try increasing and decreasing the altitude quickly this time while still maintaining control.1. Use the right stick to practice moving forward and backwards.2. Use the left and right stick to practice turns and banking.RotateDirection ThrottleSlowly raise the throttle stick and observe just as the helicopter lifts off the ground if it leans in a direction. You can use the trim to correct this action.1. Adjustment of Left/Right trim Just before the quadcopter lifts-off, the nose leans left/right.When it leans right adjust the trim to the left side.When it leans left adjust the trim to the right side.2. Adjustment of Forwards/Backwards trim Just before the quadcopter lifts-off, the nose leans forward/backwards.When it leans forwards adjust the trim down.When it leans backwards adjust the trim up.3. Adjustment of Roll trim Just before the quadcopter lifts-off, the body rolls left/right.When it rolls right adjust the trim to the left side.When it rolls left adjust the trim to the right side.Rotor BladesUpper bodyBottom bodyMotorLy-polymer batteryReceiver board Stable, flexible, 3D to roll easily Stable, flexible, 3D to roll easily2MAfter you skilled above basic movements, you can play some of the breathtaking tumbling action.First, the aircraft flew more than 2 meters’ height; Press the key rollover, then push the stick of forward/backward, or left /right to top then release the aircraft can roll over.1x Small screwdriver
FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Note 2: 1.Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2. The minimum separation generally be used is at least 20 cm.

Navigation menu