Apex Toys GD-90C Hunter User Manual GD 90C 171017
Apex Toys (Shenzhen)Co., Ltd. Hunter GD 90C 171017
15_GD-90C UserMan
PACKAGE CONTENTS IMPORTANT 1. This product is only suitable for users overthe age of 8. Piloting this quadcopter will be dificult at the beginning. We recommend be occampanied by an experienced pilot at first. 2. This product is designed with high-tech electronics and mechanical parts. Do not fly near people. Improper operation can result in injury or property damage. We will not accept any responsibility for this. 3. We will not take any responsibilty for accidents during the operation of this device. 4. Contact cutomer service for help if you have any problems with the device. Cautions: REMOTE CONTROL FUNCTIONS 1x USB cable controller Speed/Stunt 4x spare blades 1x Small screwdriver Take photo/video Headless mode On/off button The throttle rocker QUADCOPTER COMPONENTS 1.Checking the surroundings before flying. 2.Do not let the plane fly out of sight when flying. 3.Do not let the child play alone, play together with adult. 4.Please make sure, there is no other player use the same frequency at the same area. The direction rocker Left and right fine-tuning One key to return back One key to take off Front and back fine-tuning One key to land Do not fly in these areas. High-voltage power lines The places of Crowds Positive rotor blades Reverse rotor blades Positive rotor Reverse rotor 10.One key to retur n Short press the button for one key to return . Press again to finish return . 11.Calibration (1) if the aircraft is drifting to one side during takeoff, it can be calibrated to make the flight more stable (2)calibration method: the aircraft is placed on the horizontal surface, and the two rocker of the remote control is pushed to the lower right corner, when observed the indicator light flashes on the aircraft, release the remote control rocker, indicating that it has been calibrated. (note: the aircraft should be kept at the horizontal surface. During calibration, the aircraft will not be able to riot . After the calibration is completed, the indicator light will stop flash quickly). 12:Low Volatage War ning: When the voltage of battery is lower than 2.5V,power light will blink ,which means you have to change the battery. Meanwhile, a “beep beep”sound will send from the buzzer,which means you have to stop flying the vehicle. Rainstorm and thunderstorm Near the railway Roads and nearby places Forests and rivers High winds Rotate Camera 10 Camera board 1.On/off (1)On(After put on the battery, R/C is in sleep model,indicator extinguish when off) Short Press the ON/OFF, the remote control enters the normal mode of work, the buzzer is short sound one beeping, and the power indicator is fading. (2)Power off: long press the ON/OFF, the buzzer is short sound two beeping, the power indicator is out and the remote control is off. 2.Tur ning When the remote control and the aircraft are pairing the code, move the turning rocker to left and right,the aircraft will turn left and right. 3.Forward and backward When the remote control and the aircraft are pairing the code, move the rocker to forward and backward, the aircraft will fly forward and backward. 4.Left and right When the remote control and the aircraft are pairing the code, move the rocker to left and right,the aircraft will fly left and right. 5.Fine-tuning function The aircraft can be stabilized by adjusting the direction of the aircraft, in the opposite direction of flight. 6.Headless mode Short press the button to enter headless mode. The vehicle’s flying direction will be the same as the demand of controller,no matter where the head is . 7.Speed/Stunt Short press the button to adjust the speed. There are three speed levels.You will hear a beep sound while adjusting . Beep one for level 1 ,beep two for level 2, beep three for level 3. The higher the level ,the faster the speed.Long press the button for stunt .The beeper will keep. ringing. 8.Take photo/video short press the button to take photo,long press the button to take video,press again to finish video 9.One key take off and one key landing In the fixed high mode,after press the one key take off and one key landing buttons, automatically aircraft up to one meter from the ground level hover, trigger buttons again, aircraft flying will fall to the ground stops automatically INSTALL A MICRO SD CARD Throttle The propeller system is a precision instrument that may need to be repaired or replaceed from time to time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to propeller blades. 1.The aircraft has four blades, two white colors on front, and two black colors on back (see the diagram below). 2.When replacing the propeller blades, make sure to match both the color of the blade and the indication letter on the blade. Direction If a MicroSD card is not installed the LEDs will flash 5 times. When a MicroSD card is intalled the leds will stay illuminated. Micro SD card sold seperately. 8G(FAT&FAT32 format) FLIGHT ADJUSTMENT AND NOTICE FOR BEGINN E RS As shown in the figure, push the rocker of the remote control to the position in the lower right corner at the same time. At this time the indicator light of the aircraf t flashes and then loosens the remote control, and the indicator light is always on and the calibration is complete. WARNING Battery charge Mobile phone adapter:Output: 5V Charging current: 1-2A. BATTERY WARNINGS RECHARGEABLE BATTERY: This Quadcopter uses a Li-Poly rechargeable battery.If battery no longer stays charged,dispose of battery properly according to local disposal requirements. CONTROLLER BATTERIES: Remote control requires 2”AAA”batteries (not included).Please read the important battery safety warning below. ●Do not mix alkaline,standard (carbon-zinc) and rechargeable betteries (Nickel Metal Hydride). ●Do not mix old and new batteries. ●Non-rechargeable batteries are not to be recharged. ●Rechargeble batteries are to be removed from the item before being charged (if removable). ●Rechargeble batteries are only to be charged under adult supervision. ●Exhausted batteries should be removed immediately and must be recycled or disposed of properly according to state or local government ordinances and reulations. ●The supply terminals are not to be short-circuited. ●Only batteries of the same or equivalent type as recommended are to be used. ●Batteries are to be inserted with the correct polarity (see inside booklet for diagram). ●Do not dispose batteries in a fire-batteries may leak or explode. CAMERA / VIDEO OPERATION CAUTION Make sure that no people or obstructions are in the vicinity. You must first practice hovering to fly safely, this is a basic flight action(meaning keep the helicopter in mid air in a fixed position) Please stand approximately 6ft diagonally behind the helicopter. The remote control can control the quadcopter’s camera. Slowly raise the throttle stick and observe just as the helicopter lifts off the ground if it leans in a direction. You can use the trim to correct this action. 1. Adjustment of Left/Right trim Just before the quadcopter lifts-off, the nose leans left/right. When it leans right adjust the trim to the left side. When it leans left adjust the trim to the right side. 1. The throttle is on the left hand, push the throttle a little up to raise the copter to your line of sight then pull down a little to let the quadcopter slowly down to the floor. Repeat until you can easily and quickly control the altitude. 2.Hovering flight practic: Raise the quadcopter to a certain height then hover at that altitude. 3.Try increasing and decreasing the altitude quickly this time while still maintaining control. 2. Adjustment of Forwards/Backwards trim Just before the quadcopter lifts-off, the nose leans forward/backwards. When it leans forwards adjust the trim down. When it leans backwards adjust the trim up. 3. Adjustment of Roll trim Just before the quadcopter lifts-off, the body rolls left/right. When it rolls right adjust the trim to the left side. When it rolls left adjust the trim to the right side. 400 After turn on the quadcopter the LED indicators keep flashing but the quadcopter does not respond. No response after the battery is connected to the quadcopter. • Sync the remote control and copter (refer to P.7) • F ully charge the battery Transmitter and receiver fail pairing Check whether it is low power Charging the helicopter Photo Mode: Press the camera button to take a picture. The LED on the quadcopter will flash once to confirm it took a picture. Video Mode: Press the video button to start recording a video. The LED on the quadcopter will blink slowly while it is recording. Press the video button again to stop recording. To access the photos and video you will need a MicroSD card reader. The maximum capacity of MicroSD card is 64G(FAT format) Main rotor continues to spin after landing Throttle stick not on the lowest position Helicopter rotor spins but unable to take off. 1.Check whether the blade assembled correctly or not. 2.Helicopter battery depleted. The helicopter still keeps turning after rudder triming or inconsistent speed during left/right pirouette. 1. The blades haven’t been installed in the right place. 2. Rotor blade deformation 3. Didn’t calibrate the flight. The quadcopter still keeps turning after trimming the rudder trim, or inconsistent speed during left/right turns. 1.The blade isn’t fully installed 2. Rotor blade deformation 3.Rotor blade not match code Make sure the Throttle stick is on the lowest position 1. Replace the main wing Replace the main motor 2. Change blade 3. Correct the level refer to P6 • Ch ange blade • Correct the level refer to P6 • Replace the main wing • Replace the main motor GD-90C CAUTIONS The quadcopter shifts forwards/ backwards. The trim is not even. • Trim the elevator back to center. • Restart the remote control. QUADCOPTER COMPONENTS Stable, flexible, 3D to roll easily Can not fly the helicopter after crashing PLEASE PRACTICE SIMULATED FLIGHT BEFORE ACTUAL FLYING Before you are familiar with the unit, please don't pilot it . Read the instruction carefully to get familiar with the direction controls. 1. Checking that propellers are securely attached to the motors. Pull the throttle down to prevent takeoff. 2. Place quadcopter in a clear open field and point the tail towards yourself. 3. Practice operating the control sticks (as shown below), and repeat practicing “Throttle high/low”, “ Left/right ”, “Forward/backward”, and “bank left/right”. 4.Strong impacts can jam the motors, using a long flat nose plier to unjam to rotor. 5.The simulation flight practice is very important, please keep practicing until you are comfortable with the controls. The LED will be on continuously while the quadcopter is on. When it is low on power the indicator will blink. Please land the quadcopter. CAUTION Check if the screws and blades are firmly tightened Check if the transmitter and helicopter are fully charged. When not in use for a long time, please take out the remote control batter y and keep it properly. Note: If the remote control batter y is not removed, the long storage will cause the leakage of the batter y and damage the remote control device. FLIGHT ADJUSTMENT AND SETTING During the flight, the indicator light of the aircraft is slow to flash while the remote control makes a "beep beep", indicating that the battery voltage is insufficient and please land down to recharge the battery. Solution Important: Be sure the surface is flat and level. The quadcopter needs to calibrate it’s orientation. STEP 2 Caution TROUBLE SHOOTING DURING FLIGHT STEP 1 3.7V 400mAh Li-Po Battery Charge with our dedicated charger . 3.Replace broken blades with the correct blade. SYNCING THE REMOTE CONTROL & QUADCOPTER Insert the battery into the quadcopter and connect the plug. The two indicators will begin flashing. Place the quadcopter on a flat surface. 1.Take off the battery from the vehicle. Connect the battery with a USB cable . Plug the USB cable into a mobile phone adapter or a computer. 2.The Charging Indicator will blink when charging. The Charging Indicator will turn OFF when fully charged . 1. Use the right stick to practice moving forward and backwards. 2. Use the left and right stick to practice turns and banking. 2M Stable, flexible, 3D to roll easily After you skilled above basic movements, you can play some of the breathtaking tumbling action. First, the aircraft flew more than 2 meters’ height; Press the key rollover, then push the stick of forward/backward, or left /right to top then release the aircraft can roll over. 1.Rotor blade turns off 2. Rotor blade deformation . Change replacement rotors . Tighten the Rotors CONTROLLER INSTRUCTION REPLACING THE PROPELLER BLADE FLIGHT CHARGING SYNCING THE REMOTE CONTROL AND THE QUADCOPTER FLIGHT ADJUSTMENT AND SETTINGS INSTALLING A MICROSD CARD CAMERA OPERATION FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Note 2: 1.Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2. The minimum separation generally be used is at least 20 cm.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Title : GD-90C说明书更新171017 Metadata Date : 2017:11:23 16:50:46+08:00 Modify Date : 2017:11:23 16:50:46+08:00 Create Date : 2017:10:20 15:48:22+09:00 Creator Tool : Adobe Illustrator CS6 (Windows) Thumbnail Width : 256 Thumbnail Height : 140 Thumbnail Format : JPEG Thumbnail Image : (Binary data 15725 bytes, use -b option to extract) Instance ID : uuid:a60f324a-b9ac-454b-9221-1dd0526f3213 Document ID : xmp.did:156243B36AB5E7119D20BF3FB8DAE79E Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:146243B36AB5E7119D20BF3FB8DAE79E Derived From Document ID : xmp.did:146243B36AB5E7119D20BF3FB8DAE79E Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : converted, saved, converted, converted, saved, saved, saved, saved, saved, converted, saved, converted, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, converted, saved, converted, saved, converted, saved, converted, saved, saved, saved, saved, saved, saved, saved History Params : from application/pdf toEXIF Metadata provided by EXIF.toolsHistory Instance ID : xmp.iid:D27F11740720681191099C3B601C4548, xmp.iid:F97F1174072068118D4ED246B3ADB1C6, xmp.iid:FA7F1174072068118D4ED246B3ADB1C6, xmp.iid:EF7F117407206811A46CA4519D24356B, xmp.iid:F07F117407206811A46CA4519D24356B, xmp.iid:F77F117407206811BDDDFD38D0CF24DD, xmp.iid:F97F117407206811BDDDFD38D0CF24DD, xmp.iid:FA7F117407206811BDDDFD38D0CF24DD, xmp.iid:FB7F117407206811BDDDFD38D0CF24DD, xmp.iid:FC7F117407206811BDDDFD38D0CF24DD, xmp.iid:FD7F117407206811BDDDFD38D0CF24DD, xmp.iid:FE7F117407206811BDDDFD38D0CF24DD, xmp.iid:B233668C16206811BDDDFD38D0CF24DD, xmp.iid:B333668C16206811BDDDFD38D0CF24DD, xmp.iid:B433668C16206811BDDDFD38D0CF24DD, xmp.iid:F77F11740720681197C1BF14D1759E83, xmp.iid:F87F11740720681197C1BF14D1759E83, xmp.iid:F97F11740720681197C1BF14D1759E83, xmp.iid:FA7F117407206811B628E3BF27C8C41B, xmp.iid:FF7F117407206811B628E3BF27C8C41B, xmp.iid:07C3BD25102DDD1181B594070CEB88D9, xmp.iid:F87F1174072068119098B097FDA39BEF, xmp.iid:F77F117407206811BB1DBF8F242B6F84, xmp.iid:F97F117407206811ACAFB8DA80854E76, xmp.iid:0180117407206811834383CD3A8D2303, xmp.iid:F77F117407206811818C85DF6A1A75C3, xmp.iid:C9E331F5BE206811A7CEA1A024F2DF66, xmp.iid:156243B36AB5E7119D20BF3FB8DAE79E History When : 2008:04:17 14:19:15+05:30, 2008:05:15 16:23:06-07:00, 2008:05:15 17:10:45-07:00, 2008:05:15 22:53:33-07:00, 2008:05:15 23:07:07-07:00, 2008:05:16 10:35:43-07:00, 2008:05:16 10:40:59-07:00, 2008:05:16 11:26:55-07:00, 2008:05:16 11:29:01-07:00, 2008:05:16 11:29:20-07:00, 2008:05:16 11:30:54-07:00, 2008:05:16 11:31:22-07:00, 2008:05:16 12:23:46-07:00, 2008:05:16 13:27:54-07:00, 2008:05:16 13:46:13-07:00, 2008:05:16 15:47:57-07:00, 2008:05:16 15:51:06-07:00, 2008:05:16 15:52:22-07:00, 2008:05:22 13:28:01-07:00, 2008:05:22 16:23:53-07:00, 2008:05:28 16:45:26-07:00, 2008:06:02 13:25:25-07:00, 2008:06:09 14:58:36-07:00, 2008:06:11 14:31:27-07:00, 2008:06:11 22:37:35-07:00, 2008:06:27 14:40:42-07:00, 2015:12:22 14:59:22-08:00, 2017:10:20 15:48:11+08:00 History Software Agent : Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS4, Adobe Illustrator CS6 (Windows) History Changed : /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, / Startup Profile : Print Has Visible Overprint : False Has Visible Transparency : False N Pages : 1 Max Page Size W : 22.972222 Max Page Size H : 12.826389 Max Page Size Unit : Inches Font Name : ArialMT, Arial-ItalicMT, Arial-BoldMT, Arial-Black, SimHei, SimSun, AdobeSongStd-Light, MicrosoftYaHei, MicrosoftYaHei-Bold, MyriadPro-Regular, MS-Mincho, FZLTXHK--GBK1-0 Font Family : Arial, Arial, Arial, Arial, 黑体, 宋体, Adobe 宋体 Std, 微软雅黑, 微软雅黑, Myriad Pro, MS 明朝, 方正兰亭细黑_GBK Font Face : Regular, Italic, Bold, Black, Regular, Regular, L, Regular, Bold, Regular, 標準, Regular Font Type : Open Type, Open Type, Open Type, Open Type, Open Type, TrueType, Open Type, Open Type, Open Type, Open Type, TrueType, TrueType Font Version : Version 5.22, Version 5.22, Version 5.22, Version 5.06, Version 5.01, Version 5.03, Version 5.016;PS 5.002;hotconv 1.0.67;makeotf.lib2.5.33168, Version 6.02, Version 6.02, Version 2.102;PS 2.000;hotconv 1.0.67;makeotf.lib2.5.33168, Version 5.01, 1.00 Font Composite : False, False, False, False, False, False, False, False, False, False, False, False Font File Name : arial.ttf, ariali.ttf, arialbd.ttf, ariblk.ttf, simhei.ttf, simsun.ttc, AdobeSongStd-Light.otf, msyh.ttf, msyhbd.ttf, MyriadPro-Regular.otf, msmincho.ttc, 方正兰亭细黑_0.TTF Plate Names : Cyan, Magenta, Yellow, Black Swatch Group Name : 默认色板组, Grays, Brights Swatch Group Type : 0, 1, 1 Swatch Colorant Swatch Name : White, Black, CMYK Red, CMYK Yellow, CMYK Green, CMYK Cyan, CMYK Blue, CMYK Magenta, C=15 M=100 Y=90 K=10, C=0 M=90 Y=85 K=0, C=0 M=80 Y=95 K=0, C=0 M=50 Y=100 K=0, C=0 M=35 Y=85 K=0, C=5 M=0 Y=90 K=0, C=20 M=0 Y=100 K=0, C=50 M=0 Y=100 K=0, C=75 M=0 Y=100 K=0, C=85 M=10 Y=100 K=10, C=90 M=30 Y=95 K=30, C=75 M=0 Y=75 K=0, C=80 M=10 Y=45 K=0, C=70 M=15 Y=0 K=0, C=85 M=50 Y=0 K=0, C=100 M=95 Y=5 K=0, C=100 M=100 Y=25 K=25, C=75 M=100 Y=0 K=0, C=50 M=100 Y=0 K=0, C=35 M=100 Y=35 K=10, C=10 M=100 Y=50 K=0, C=0 M=95 Y=20 K=0, C=25 M=25 Y=40 K=0, C=40 M=45 Y=50 K=5, C=50 M=50 Y=60 K=25, C=55 M=60 Y=65 K=40, C=25 M=40 Y=65 K=0, C=30 M=50 Y=75 K=10, C=35 M=60 Y=80 K=25, C=40 M=65 Y=90 K=35, C=40 M=70 Y=100 K=50, C=50 M=70 Y=80 K=70, C=0 M=0 Y=0 K=100, C=0 M=0 Y=0 K=90, C=0 M=0 Y=0 K=80, C=0 M=0 Y=0 K=70, C=0 M=0 Y=0 K=60, C=0 M=0 Y=0 K=50, C=0 M=0 Y=0 K=40, C=0 M=0 Y=0 K=30, C=0 M=0 Y=0 K=20, C=0 M=0 Y=0 K=10, C=0 M=0 Y=0 K=5, C=0 M=100 Y=100 K=0, C=0 M=75 Y=100 K=0, C=0 M=10 Y=95 K=0, C=85 M=10 Y=100 K=0, C=100 M=90 Y=0 K=0, C=60 M=90 Y=0 K=0 Swatch Colorant Mode : CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK Swatch Colorant Type : PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS Swatch Colorant Cyan : 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 0.000000, 14.999998, 0.000000, 0.000000, 0.000000, 0.000000, 5.000001, 19.999999, 50.000000, 75.000000, 84.999996, 90.000004, 75.000000, 80.000001, 69.999999, 84.999996, 100.000000, 100.000000, 75.000000, 50.000000, 35.000002, 10.000002, 0.000000, 25.000000, 39.999998, 50.000000, 55.000001, 25.000000, 30.000001, 35.000002, 39.999998, 39.999998, 50.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 84.999996, 100.000000, 60.000002 Swatch Colorant Magenta : 0.000000, 0.000000, 100.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 90.000004, 80.000001, 50.000000, 35.000002, 0.000000, 0.000000, 0.000000, 0.000000, 10.000002, 30.000001, 0.000000, 10.000002, 14.999998, 50.000000, 94.999999, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 94.999999, 25.000000, 44.999999, 50.000000, 60.000002, 39.999998, 50.000000, 60.000002, 64.999998, 69.999999, 69.999999, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 75.000000, 10.000002, 10.000002, 90.000004, 90.000004 Swatch Colorant Yellow : 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 0.000000, 0.000000, 0.000000, 90.000004, 84.999996, 94.999999, 100.000000, 84.999996, 90.000004, 100.000000, 100.000000, 100.000000, 100.000000, 94.999999, 75.000000, 44.999999, 0.000000, 0.000000, 5.000001, 25.000000, 0.000000, 0.000000, 35.000002, 50.000000, 19.999999, 39.999998, 50.000000, 60.000002, 64.999998, 64.999998, 75.000000, 80.000001, 90.000004, 100.000000, 80.000001, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 94.999999, 100.000000, 0.000000, 0.003099 Swatch Colorant Black : 0.000000, 100.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 10.000002, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 10.000002, 30.000001, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 25.000000, 0.000000, 0.000000, 10.000002, 0.000000, 0.000000, 0.000000, 5.000001, 25.000000, 39.999998, 0.000000, 10.000002, 25.000000, 35.000002, 50.000000, 69.999999, 100.000000, 89.999402, 79.998797, 69.999701, 59.999102, 50.000000, 39.999402, 29.998803, 19.999701, 9.999102, 4.998803, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.003099 Producer : Adobe PDF library 10.01 Page Count : 2 Creator : Adobe Illustrator(R) 16.0 For : Administrator, Bounding Box : -733 953 834 1810 Container Version : 11 Creator Version : 16