Applied Micro Design 1456FFDPA-700 Model 1456 FFDPA-700 MHz Multi-Carrier In-Building Amplifier User Manual

Applied Micro Design, Inc Model 1456 FFDPA-700 MHz Multi-Carrier In-Building Amplifier

User Manual

City and County ofSan Francisco (CCSF)Underground RF SystemsReplacement ProjectContract No. 1240Applied Micro Design Inc.Fiber-Fed Dual Power Amplifier (FFDPA)User’s ManualModel 1456FFDPAUM01456-2201rev 3CURRENT FLTREFL PWRFWD PWR CURRENTFANTEMPETHERNETFAN FLTTEMP FLTSTATUS KEYREFL PWRFWD PWRPORT 2SAMPLEPORT 1SAMPLERF OUTETHERNETCURRENT TEMPFANTEMP FLTCURRENT FLT FAN FLTPOWERRF INSTATUS KEYMODEL 1466FFDPADUAL AMPLIFIERSTATUSFWD PWR REFL PWRKEYCURRENT CURRENT FLTTEMP TEMP FLTFAN FAN FLTSTATUSFWD PWR REFL PWRKEYCURRENT CURRENT FLTTEMP TEMP FLTFAN FAN FLTRF INRF OUTETHERNETDUAL AMPLIFIERMODEL 1456FFDPA-700SAMPLE PORT 1 SAMPLE PORT 2ETHERNETPOWERPRIMARY SECONDARYRESETOFF
19516 Amaranth Drive Germantown MD 20874 ph 301.540.9506 | info@appliedmicrodesign.com | www.appliedmicrodesign.comApplied Micro Design Inc.PROPRIETARYThis document is issued in strict confidence on condition that it is not copied, reprinted, or disclosed to a third party, wholly or in part, without written consent of Applied Micro Design, Incorporated.2
Table of ContentsNotes, Cautions, and WarningsSystem Specifications and Block DiagramIntroduction and DescriptionFront Panel and Indicators3
4This is a Class B Booster.Notes, Cautions, and Warnings!Connect RF Output to existing Distributed Antenna System (DAS) cable only.DO NOT operate equipment with unauthorized antennas, cables, and/or coupling devices.DO NOT operate equipment unless all RF connectors are secure.DO NOT operate equipment unless it has been installed and inspected by a qualified radio technician.Contact InformationFor more information contact the FCC at:https://signalboosters.fcc.gov/signal-boosters/F.2 PART 90 CLASS B SIGNAL BOOSTERS Licensees and signal booster operators are required to register existing Class B signal booster installations with the FCC by November 1, 2014. After November 1, 2014, operation of an existing, unregistered Class B signal booster will be unauthorized and subject to enforcement action. Any new Class B signal booster installed after November 1, 2014 must be registered prior to operation. To encourage compliance with this new requirement, registration will be free of cost to the operator and/or licensee.[R11], [R9] FCC Part 90 Class B Signal Booster Registration & Discovery website:https://signalboosters.fcc.gov/signal-boosters/
System Specifications & Block DiagramRF OutModel 1456FFDPA Product Block DiagramSpecificationsFrequency: 769 - 775 MHz, 851 - 860 MHzType: Class AB Channels: 50 maximumPower Output: 5 W (+37 dBm) CompositePower Output: + 20 dBm / carrierGain: 35 - 45 dBGain Adjust: 10 dB, Digitally controlled viaGUI or locallyALC: 5 WattsOIP3: +58 dBmImpedance: 50 OhmsLoad VSWR: Infinite, no damageN.F.: 7 dB nominalPower Supply: 115 V ACCurrent: < 2AOperating Temp: -30° to +60° C Size: 19” x 5.22” x 16”Weight: 22 lbs.DL PA P700 MHz1x2DL PA S700 MHzONOFFµPµPRF In5
Introduction & DescriptionThe 1456DPA channel amplifier is a high-linearity, multi-carrier amplifier for DAS Distributed Antenna System applications. The unit is dual-amplifier configuration. Each amplifier has its own processor board, alarms, panel indicators and power supply. An RF Switch and Switch Interface Board allow for routing either amplifier output to the common RF Output connector.The processor board controls the enable signal (Mute) to the amplifier module and monitors forward power, reverse power, current, fan status and heat sink temperature.The processor board features remote monitoring capability via Ethernet. A computer running the Graphical User Interface (GUI) can display the status of the amplifier and provide control.A front panel Look Port for each amplifier allows the user to sample each of the two signals at the front panel. The look port enables measurement without interrupting main line communications. The Look Port sample is 40 dB below the main RF output port.6
PowerSwitchRF InConnector-40 dBSample Port 2Connector-40 dBSample Port 1ConnectorEthernetConnector192.168.7.xxxIP Address192.168.7.xxxIP AddressSTATUS KEYREFL PWRCURRENT FLTTEMP FLTFAN FLTFWD PWRCURRENTTEMPFANFFDPA - Front Panel and IndicatorsModel No. 1456FFDPAsteady: amplifer is operating steady: amplifier is enabledsteady: amplifier is operating normally steady: amplifier has either current, reverse power or temperature faultCURRENT FLTREFL PWRFWD PWR CURRENTFANTEMPETHERNETFAN FLTTEMP FLTPRIMARY STATUS KEYREFL PWRFWD PWRPORT 2SAMPLEPORT 1SAMPLERF OUTETHERNETCURRENT TEMPFANTEMP FLTCURRENT FLT FAN FLTPOWERRF INSECONDARY STATUS KEYMODEL 1456FFDPA-700DUAL AMPLIFIEREthernetConnector RF OutConnectorModel Number and Frequency Band7
8Power Amplifier Installation769-775 MHz 799-805 MHzCOM 806-815 MHz 851-860 MHzCOM760-805 MHz 806-860 MHzCOMCURRENT FLTREFL PWRFWD PWR CURRENTFANTEMPETHERNETFAN FLTTEMP FLTPRIMARY STATUS KEYREFL PWRFWD PWRPORT 2SAMPLEPORT 1SAMPLERF OUTETHERNETCURRENT TEMPFANTEMP FLTCURRENT FLT FAN FLTPOWERRF INSECONDARY STATUS KEYMODEL 1456FFDPA-700DUAL AMPLIFIERCURRENT FLTREFL PWRFWD PWR CURRENTFANTEMPETHERNETFAN FLTTEMP FLTPRIMARY STATUS KEYREFL PWRFWD PWRPORT 2SAMPLEPORT 1SAMPLERF OUTETHERNETCURRENT TEMPFANTEMP FLTCURRENT FLT FAN FLTPOWERRF INSECONDARY STATUS KEYMODEL 1456FFDPA-800DUAL AMPLIFIERConnect to Distributed Antenna System (DAS)FFDPA-700DUPLEXERCBCFFDPA-800Cables shown above are shipped with the units.
Related Documents19516 Amaranth Drive Germantown MD 20874 ph 301.540.9506 | info@appliedmicrodesign.com | www.appliedmicrodesign.comApplied Micro Design Inc.9

Navigation menu