Aprilaire Thermostat 8476 Users Manual
8476 c22f763b-dabf-409d-94ec-cd27b042a0ef Aprilaire Thermostat 8476 User Guide |
2015-02-03
: Aprilaire Aprilaire-Thermostat-8476-Users-Manual-467303 aprilaire-thermostat-8476-users-manual-467303 aprilaire pdf
Open the PDF directly: View PDF 
.
Page Count: 13
| Download | |
| Open PDF In Browser | View PDF |
Model 8476 Thermostat with Event-Based™ Air Cleaning Safety & Installation Instructions READ AND SAVE THESE INSTRUCTIONS Table of contents Installation Installation Installation location recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Outdoor temperature sensor (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermostat mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power & reset options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wiring terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation location recommendations 3 4 5 5 6 7 Setup & Testing Thermostat should be mounted: Do not mount thermostat: • On an interior wall, in a frequently occupied space. • Behind doors, in corners, or other dead air spaces. • Approximately 5‘ above floor. • At least 18” from outside wall. • In direct sunlight, near lighting fixtures, or other appliances that give off heat. • Thermostat can be mounted to a vertical junction box. • On an outside or unconditioned area wall. • In the flow of a supply register, in stairwells, or near outside doors. • On a wall with concealed pipes or ductwork. System setup instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 System test mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 References Quick reference to controls & display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermostat features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 18 19 20 22 3 Installation Installation Outdoor temperature sensor (optional) Thermostat mounting Outdoor temperature can be measured by attaching an 8052 sensor to the S1 and S2 terminals. System setting #05 (Remote sensor) is used to enable sensor. • Install on side of building out of direct sunlight (north side recommended). Heat pump applications can use the outdoor temperature to effectively utilize the heat pump: • Mount at least 3’ away from exhaust vents and condensing lines. • When the outdoor temperature is less than the Low Balance Point, the heat pump will be locked out and only auxiliary heating will be used. • Maximum wire length is 300’. Power & Reset options The thermostat is dual power. It can either be AC or battery powered, or both (to provide backup power for the clock). Batteries are optional if the thermostat was connected to AC power when installed. • Mount above snow line. 24 VAC must be connected in order for the system fault and emergency heat indicators to operate. The thermostat has a memory backup that saves the thermostat’s settings in case of a power interruption. • Do not route wires along 120 VAC lines. • When the outdoor temperature is higher than the High Balance Point, the auxiliary heating will be locked out and only the heat pump will be used to provide heating. The reset button located under the battery cover can be used to reset the thermostat back to factory defaults. The system settings will also be reset back to defaults. 1. Remove the back of the thermostat, by pressing the tab on the bottom of the unit. 2. P ull wires through the opening on the back of the thermostat. 3. Position and level the back of the thermostat on wall and mark the hole locations with a pencil. 4. Drill 1/4” holes & insert supplied anchors (drywall only). RC R 4 W Y G C S1 S2 O/B L W2 Y2 5. Place back over anchors, insert and tighten screws. 6. Seal wire entry holes to prevent drafts affecting temperature readings. 5 Installation Wiring terminal Wiring – single Transformer (use Jumper Wire) for HEAT/COOL System NOT USED 2nd HEATING G 2nd COOLING Y NOT USED W OUTDOOR TEMP SENSOR COOLING TRANSFORMER 2nd HEATING 2nd COOLING G NOT USED Y C S1 S2 O/B L W2 Y2 RC R 6 W FAN Y G 1st HEATING W 1st COOLING RC R NOT USED *Jumper between RC & R is used in single transformer systems (see wiring diagrams). OUTDOOR TEMP SENSOR • Push the excess wire back into the opening and plug the wall opening to prevent drafts. FAN • Loosen screw terminals, insert stripped wire and re-tighten. 1st HEATING • Ensure power at the HVAC equipment is off. 1st COOLING Installation notes RC – 24 VAC supply cooling* R – 24 VAC supply heating* W – 1st stage heat / auxiliary Y – 1st stage cooling / compressor G – Fan C – Common (optional when powered by batteries) S1 & S2 – outdoor temperature sensor (optional) O/B – Reversing valve L – System fault indicator W2 – 2nd stage heat / auxiliary Y2 – 2nd stage cooling / compressor JUMPER 18-24 gauge thermostat wire TRANSFORMER Wire specifications Wiring – TWO TransformerS (REMOVE Jumper Wire) for HEAT/COOL System HEATING TRANSFORMER Installation C S1 S2 O/B L W2 Y2 RC R C S1 S2 O/B L W2 Y2 7 Installation Setup & Testing System setup instructions Wiring – TWO TransformerS (REMOVE Jumper Wire) for HEAT Pump System The following instructions show how to enter the system setup menu and change settings. The table on the following pages lists the settings and their details. Default settings are shown in bold. Some settings are only available based on other setting values. HEATING TRANSFORMER Wiring – single Transformer (use Jumper Wire) for HEAT PUMP System How to enter the system setup menu to change system settings repeatedly until system is set to OFF. Press and hold and for three seconds. 2nd COMPRESSOR FAULT DETECT 2nd AUX HEATING REVERSE VALVE OUTDOOR TEMP SENSOR FAN 1st AUX HEATING The screen of the first setting will be displayed. 1st COMPRESSOR HEAT PUMP TRANSFORMER 2nd COMPRESSOR FAULT DETECT 2nd AUX HEATING REVERSE VALVE OUTDOOR TEMP SENSOR FAN 1st AUX HEATING 1st COMPRESSOR JUMPER HEAT PUMP TRANSFORMER Press Press or Press to change to the next option. Press displayed. after the last setting. “DONE” will be to change the setting. The thermostat will return to Normal mode if no button is pressed in 3 seconds. To reset all system settings back to default, press the RESET button located under the battery door. SETTING VALUE SYSTEM SETTING NUMBER RC R 8 W Y G C S1 S2 O/B L W2 Y2 RC R W Y G C S1 S2 O/B L W2 Y2 9 Setup & Testing Setup & Testing System setup instructions (continued) System setup instructions (continued) The Model 8476 thermostat has the option of being used in heat pump or heat/cool systems. Switch SW1 located on the back of the thermostat’s face is used to select this. System setting number 00 will only be shown on these models to display the position of SW1. SW1 HEAT PUMP HEAT/COOL 10 System setting Setting range, default in bold 00 Equipment type (Set by SW1) 0 : heat/cool 1 : heat pump 01 Temperature scale 0 : Fahrenheit 1 : Celsius 02 Fan control in heating 0 : Gas or oil furnace (Equipment controls fan) 1 : Electric (Thermostat controls fan) 03 Offset temperature for internal sensor 0° : No offset applied –4°F to +4°F (–2°C to +2°C) 04 Auto mode 0 : Auto mode is disabled 1 : Auto mode is enabled 05 Outdoor temperature sensor 0 : No outdoor temperature sensor attached 1 : Outdoor temperature sensor attached 06 Compressor minimum off time 5 minutes 1 to 5 minutes in 1 minute steps 07 Heating minimum off time 2 minutes 1 to 5 minutes 08 Equipment minimum on time 2 minutes 1 to 5 minutes 11 Setup & Testing Setup & Testing System setup instructions (continued) System setup instructions (continued) System setting Setting range, default in bold System setting Setting range, default in bold 09 1st stage differential 1°F (0.5°C) 1°F to 4°F (0.5°C to 2°C) 16 Low Balance Pt. (heat pump only) 20°F (–7°C) 1°F to 35°F (–17°C to 1°C) or “OFF” to disable 10 2nd stage differential 1°F (0.5°C) 1°F to 4°F (0.5°C to 2°C) 17 High Balance Pt. (heat pump only) 11 3rd stage differential (heat pump only) 1°F (0.5°C) 1°F to 4°F (0.5°C to 2°C) 19 Program format 0 – 5/2 program (Weekdays and Weekends) 1 – 5/1/1 program (Weekdays, Sat. and Sun.) 12 Reverse valve (heat pump only) 0 – O/B energized in cooling (O) 1 – O/B energized in heating (B) 20 Change air filter OFF 1, 3, 6, 12 months or “OFF” to disable 13 Integral factor period (P+I control)* Set to OFF for proportional control only 4 minutes 1 to 5 minutes or “OFF” to disable 14 Deadband (auto mode) 3°F (2°C) 2°F to 5°F (1°C to 3°C) 15 Progressive recovery 0 : Progressive recovery is disabled 1 : Progressive recovery is enabled *The integral factor is used in the equipment control algorithm to maintain the space temperature at set point. A short integral factor period will increase the number of cycles per hour. (A short integral factor period will be more comfortable.) A long integral factor period will lower the number of cycles per hour. (A long integral factor period will be more economical.) 12 System setting 05 must be enabled System setting 05 must be enabled 21 Change water panel** Set number of months until reminder is required 22 Humidifier type** 60°F (16°C) 40°F to 80°F (4°C to 27°C) or “OFF “ to disable OFF 1 to 12 months or “OFF” to disable 0 : Flow through type humidifier (1 reminder per season) 1 : Drain-less type humidifier (2 reminders per season) **If humidifier type is set to Drain-less, then the first reminder is based on the system setting 21, second reminder will activate 3 months later. If humidifier type is set to Flow through, then the first reminder is based on system setting 21, second reminder will activate 12 months later. 13 Setup & Testing Setup & Testing System test mode System test mode (continued) The system test mode is used to test a system after installation. The outputs of the thermostat can be manually activated one at a time to test their function. The following instructions show how to enter the test mode and turn outputs on and off. The charts on the following pages show the output status for each test step for Heat/Cool and Heat Pump mode. How to enter the system test menu Press repeatedly until system is set to OFF. Press and hold and for three seconds. The screen of the first test step #50 is displayed: The test steps are: Test Number Heat/Cool Heat Pump 50 Heating (W) (W2) Aux Heating (W) (W2) 51 Cooling (Y) (Y2) Compressor Cooling (Y) (Y2) 52 Fan (G) Compressor Heating (Y) (Y2) 53 14 Fan (G) Press to turn on the output (01). For multi stage output, press again to turn on the 2nd stage (02). Press to turn off the output (00). Press to change to the next test step. Press displayed. after the last test step. “DONE” will be The thermostat will return to Normal mode if no button is pressed in 3 seconds. SYSTEM TEST NUMBER FLASHES IF 24VAC IS NOT PRESENT MODE (SW1 SETTING) OUTPUT STATUS 15 Setup & Testing Setup & Testing Test steps for Heat/Cool System Setting Step Key Input 1st [UP] #50 Heat #51 Cool #52 Fan 2nd [UP] [DOWN] 1st [UP] 2nd [UP] [DOWN] [UP] [DOWN] #2 0 : Gas 1 : Elec 0 : Gas 1 : Elec 01 HEATING ON (W) ON ON ON ON 02 HEATING ON (W2) ON ON Test steps for Heat Pump Display (Output) 02 01 COOLING COOLING ON (Y2) ON (Y) ON ON ON System Setting 01 FAN ON (G) ON ON ON ON ON Step #50 Aux #51 Cool #53 Fan #2 [DOWN] 0 : Gas 1 : Elec 0 : Gas 1 : Elec 1st [UP] 2nd [UP] [DOWN] 1st [UP] 2nd [UP] [DOWN] [UP] [DOWN] 1st [UP] #52 Heat 16 Key Input 2nd [UP] #12 0:O 1:B 0:O 1:B 0:O 1:B 0:O 1:B 0:O 1:B 0:O 1:B 01 AUX HEATING ON (W) ON ON ON ON 02 AUX HEATING ON (W2) ON ON Display (Output) 02 01 COOL/HEAT COOL/HEAT ON (Y2) ON (Y) ON ON ON ON ON ON ON ON ON ON ON ON 01 FAN ON (G) ON ON ON ON ON ON ON ON ON ON ON O/B ON ON ON ON ON ON 17 Quick Reference to controls & Display Current Indoor Temperature Current Time Thermostat Features Outdoor Temperature (OPTIONAL) System Mode Setting Temperature SetTING Equipment Status clean air Setting UP System Mode down clean air Hold Program HEAT PUMP ONLY Includes Event-Based ™ Air Cleaning Emergency heat (RED) System FAULT (YELLOW) • Event-Based™ Air Cleaning. • Large, clear, backlit display is easy to read – even in the dark. • Displays room temperature, temperature setting, and optional outdoor temperature. • Dual power option (Battery or 24 VAC). • Front battery door access for fast, easy replacement. • Built in compressor protection. • Water panel and air filter service indicators. • System test mode. • Separately programmable weekday/weekend schedules. • Easy to use temperature control can override program schedule at any time. • Progressive recovery. Progressive Recovery feature allows the thermostat to activate the heating and cooling equipment prior to an event in order to reach the desired temperature at the start of the next scheduled event. Indicator shows through housing Quick Reference Card Battery Door Current Schedule Period Message Center Low Battery Warning Note: BACKLIGHT IS ACTIVATED WITH FIRST BUTTON PRESS AND AUTOMATICALLY TURNS OFF. 18 19 Troubleshooting Display is blank • Check circuit breaker and reset if necessary. • Make sure power switch at heating & cooling system is on. • Make sure furnace door is closed securely. • If thermostat is battery powered, make sure fresh AA alkaline batteries are correctly installed. Temperature settings do not change Make sure heating and cooling temperatures are set to acceptable ranges: Troubleshooting Heating system does not respond (“HEATING” appears on screen) Cooling system does not respond (“COOLING” appears on screen) • Check for 24 VAC at the equipment on the secondary side of the transformer between power and common. If voltage is not present, check the heating equipment to find the cause of the problem. • Check for 24 VAC at the equipment on the secondary side of the transformer between power and common. If voltage is not present, check the cooling equipment to find the cause of the problem. • Check for 24 VAC between the heat terminal (W) and the transformer common. If 24 VAC is present, the thermostat is functional. Check the heating equipment to find the cause of the problem. • Check for 24 VAC between the cooling terminal (Y) and the transformer common. If 24 VAC is present, the thermostat is functional. Check the cooling system to find the cause of the problem. • Check for loose or broken wires between the thermostat and the heating equipment. • Check for loose or broken wires between the thermostat and the cooling equipment. • Heat: 45° to 90°F (7° to 32°C). Fan does not turn on in a call for heat • Cool: 50° to 99°F (10° to 37°C). • Check System Setting #02 (Fan Control), to make sure the fan control is properly set to match the type of system (see page 11). Heat pump issues cool air in heat mode, or warm air in cool mode • Check System Setting #12 (Reversing Valve), to make sure it is properly configured for your system (see page 12). 20 Heat/cool both on at same time • Check SW1 (Equipment Type), to make sure it is set to match the installed heating/cooling equipment (see page 11). • Check to make sure heating and cooling wires are not shorted together. Heating equipment is running in cool mode • Check SW1 (Equipment Type), to make sure it is set to match the installed heating/cooling equipment (see page 11). “HEATING” is not displayed • Change the System Mode to Heat, and set the temperature level above the current room temperature. “COOLING” is not displayed • Change the System Mode to Cool, and set the temperature level below the current room temperature. 21 Specifications Specifications Environment Temperature Relative humidity Thermal Operating: 32° to 120°F (0° to 48.9°C) Outdoor temperature sensor Maximum distance: 300 feet Shipping: -30° to 140°F (-34.4° to 60°C) Room temperature measurement Display range: 32° to 99°F (0° to 40°C) Operating: 5% to 90% R.H. (non-condensing) Outdoor temperature measurement Display range: -20° to 130°F (-30° to 55°C) Temperature setting range Electrical Operating voltage Current Heat: 45° to 90°F (7° to 32°C) Cool: 50° to 99°F (10° to 37°C) 24 VAC (18 – 30 VAC) Maximum: 2.5A (total), 1.0A (single output) Maximum surge current: 5A Dual power. Can be battery or 24 VAC powered. Power supply Battery power 22 When both the sources are available, battery will be used as back up power. Battery power: AA size alkaline battery x 2 Battery life: Approximately 1 year 23 P.O. Box 1467 • Madison, WI 53701-1467 • Phone: 800/334-6011 • Fax: 608/257-4357 www.aprilairepartners.com 61000893 12.11 B2205693A 24 Patent Pending © 2011 Aprilaire – A division of Research Products Corporation
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.0-c060 61.134777, 2010/02/12-17:32:00 Instance ID : uuid:a3bae344-1871-4e40-9417-2d3af92c1f12 Document ID : adobe:docid:indd:a69d6098-5821-11de-b7ec-efb73c01b518 Original Document ID : adobe:docid:indd:a69d6098-5821-11de-b7ec-efb73c01b518 Rendition Class : proof:pdf Derived From Instance ID : f2a2423a-46e1-11de-b7ec-efb73c01b518 Derived From Document ID : adobe:docid:indd:6da3d132-21df-11de-9d41-ef890f5c2338 History Action : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:F28DBA83F3236811822ACE92B44A1BB7, xmp.iid:F38DBA83F3236811822ACE92B44A1BB7, xmp.iid:6C531E28F4236811822ACE92B44A1BB7, xmp.iid:0664A172F4236811822ACE92B44A1BB7, xmp.iid:2F35D0B8F4236811822ACE92B44A1BB7, xmp.iid:E8FAB1EAF4236811822ACE92B44A1BB7, xmp.iid:207A2C2FF5236811822ACE92B44A1BB7, xmp.iid:2335293FF5236811822ACE92B44A1BB7, xmp.iid:B66CB760F5236811822ACE92B44A1BB7, xmp.iid:8B2E917EF5236811822ACE92B44A1BB7, xmp.iid:DFA5589EF5236811822ACE92B44A1BB7, xmp.iid:F806F7A5F5236811822ACE92B44A1BB7, xmp.iid:FD759EDCF5236811822ACE92B44A1BB7, xmp.iid:32858F08F6236811822ACE92B44A1BB7, xmp.iid:DC93C048F7236811822ACE92B44A1BB7, xmp.iid:33A5A57AF7236811822ACE92B44A1BB7, xmp.iid:873051CDF7236811822ACE92B44A1BB7, xmp.iid:1A304F5AFA236811822ACE92B44A1BB7, xmp.iid:C6D9EA9BFA236811822ACE92B44A1BB7, xmp.iid:EEE263BBFA236811822ACE92B44A1BB7, xmp.iid:7EB11602FB236811822ACE92B44A1BB7, xmp.iid:1B9AC862FB236811822ACE92B44A1BB7, xmp.iid:904D35C5FB236811822ACE92B44A1BB7, xmp.iid:70236A55FC236811822ACE92B44A1BB7, xmp.iid:6F34CC6CFC236811822ACE92B44A1BB7, xmp.iid:8052C4D2FD236811822ACE92B44A1BB7, xmp.iid:58F2135101246811822ACE92B44A1BB7, xmp.iid:5EEF40FB01246811822ACE92B44A1BB7, xmp.iid:F48DE5EAC1246811822ACE92B44A1BB7, xmp.iid:22D5F814C2246811822ACE92B44A1BB7, xmp.iid:2AA3034ECC246811822ACE92B44A1BB7, xmp.iid:8738C180CC246811822ACE92B44A1BB7, xmp.iid:5E6A3C89CC246811822ACE92B44A1BB7, xmp.iid:E6C40FF4CC246811822ACE92B44A1BB7, xmp.iid:F7675433EE246811822ACE92B44A1BB7, xmp.iid:52ABE39D8D256811822ACE92B44A1BB7 History When : 2011:12:12 10:39:29-06:00, 2011:12:12 10:39:29-06:00, 2011:12:12 10:44:05-06:00, 2011:12:12 10:46:10-06:00, 2011:12:12 10:48:07-06:00, 2011:12:12 10:49:31-06:00, 2011:12:12 10:51:26-06:00, 2011:12:12 10:51:53-06:00, 2011:12:12 10:52:49-06:00, 2011:12:12 10:53:39-06:00, 2011:12:12 10:54:32-06:00, 2011:12:12 10:54:45-06:00, 2011:12:12 10:56:17-06:00, 2011:12:12 10:57:31-06:00, 2011:12:12 11:06:28-06:00, 2011:12:12 11:07:52-06:00, 2011:12:12 11:10:10-06:00, 2011:12:12 11:28:26-06:00, 2011:12:12 11:30:16-06:00, 2011:12:12 11:31:09-06:00, 2011:12:12 11:33:07-06:00, 2011:12:12 11:35:50-06:00, 2011:12:12 11:38:35-06:00, 2011:12:12 11:42:37-06:00, 2011:12:12 11:43:16-06:00, 2011:12:12 11:53:16-06:00, 2011:12:12 12:19:54-06:00, 2011:12:12 12:23:02-06:00, 2011:12:13 11:16:59-06:00, 2011:12:13 11:18:10-06:00, 2011:12:13 12:31:20-06:00, 2011:12:13 12:32:45-06:00, 2011:12:13 12:35:48-06:00, 2011:12:13 12:35:59-06:00, 2011:12:13 16:33:59-06:00, 2011:12:14 11:35:08-06:00 History Software Agent : Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0 History Changed : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata Create Date : 2011:12:14 11:35:28-06:00 Modify Date : 2011:12:14 11:35:34-06:00 Metadata Date : 2011:12:14 11:35:34-06:00 Creator Tool : Adobe InDesign CS5 (7.0) Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 10808 bytes, use -b option to extract), (Binary data 10578 bytes, use -b option to extract) Doc Change Count : 465 Format : application/pdf Producer : Adobe PDF Library 9.9 Trapped : False Page Count : 13 Creator : Adobe InDesign CS5 (7.0)EXIF Metadata provided by EXIF.tools