Apw Wyott Fastrac Ft 1000 Users Manual Conveyor Toaster Inst Op 67192

Fastrac 800 ft-1000-fastrac-conveyor-toaster-67192-9-06-manual

FT 1000 to the manual f9a70e24-f08d-4144-885a-365b09b5b3a6

2015-02-05

: Apw-Wyott Apw-Wyott-Fastrac-Ft-1000-Users-Manual-510172 apw-wyott-fastrac-ft-1000-users-manual-510172 apw-wyott pdf

Open the PDF directly: View PDF .
Page Count: 12

Phone: +1 (214) 421-7366

Fax: +1 (214) 565-0976

Toll Free: +1 (800) 527-2100

Website: www.apwwyott.com

E-mail: info@apwwyott.com

INSTALLATION

AND

OPERATING

INSTRUCTIONS

INTENDED FOR OTHER THAN HOUSEHOLD USE

Model: FT 1000

RETAIN THIS MANUAL FOR FUTURE REFERENCE

UNIT MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES

P/N 67192 9/06

FASTRAC HORIZONTAL CONVEYOR TOASTER

APW WYOTT

729 Third Avenue

Dallas, TX 75226

This equipment has been engineered to provide you with year-round dependable service when used

according to the instructions in this manual and standard commercial kitchen practices.

WARNING: Improper installation, adjustment, alteration, service or maintenance can

cause property damage, injury or death. Read the Installation, Operating and

Maintenance Instructions thoroughly before installing or servicing this equipment. !!

TABLE OF CONTENTS

Safety Precautions

Important Safety Instructions

General Information

Installation Instructions

Operation Instructions

Cleaning Instructions

Warranty Procedure

Troubleshooting

Replacement Parts List

Wiring Diagram

Warranty

SAFETY PRECAUTIONS

Before installing and operating this equipment be sure everyone involved in its operation are fully trained

and are aware of all precautions. Accidents and problems can result by a failure to follow fundamental rules

and precautions.

The following words and symbols, found in this manual, alert you to hazards to the operator, service

personnel or the equipment. The words are defined as follows:

!WARNING: This symbol refers to a potential hazard or unsafe practice, which could result in

serious injury or death.

!DANGER: This symbol warns of imminent hazard which will result in serious injury or death.

!CAUTION: This symbol refers to a potential hazard or unsafe practice, which may result in minor or

moderate injury or product or property damage.

!NOTICE: This symbol refers to information that needs special attention or must be fully understood

even though not dangerous.

APW Wyott takes pride in the design and quality of our products. When used as intended and with proper

care and maintenance, you will experience years of reliable operation from this equipment. To ensure best

results, it is important that you read and follow the instructions in this manual carefully.

Installation and start-up should be performed by a qualified installer who thoroughly read, understands and

follows these instruction.

If you have questions concerning the installation, operation, maintenance or service of this product, contact

APW Wyott Foodservice Equipment Company’s “ Technical Service Department”.

IMPORTANT FOR FUTURE REFERENCE

Please complete this information and retain this manual for the life of the equipment. For

Warranty Service and/or Parts, this information is required.

Model Number Serial Number Date Purchased

Notes:

1. IMPORTANT SAFETY INSTRUCTIONS

!WARNING: Plug unit into a properly grounded electrical outlet of the correct voltage, size and plug

configuration. If the plug and receptacle do not match, contact a qualified electrician to determine

the proper voltage and size and install the proper electrical outlet.

IMPORTANT: Read the following important safety instructions to avoid personal injury or

death, and to avoid damage to the equipment or property.

!WARNING: APW Wyott toasters are designed, built, and sold for commercial use. If positioned

where the general public can usethem, make sure that all cautions, warnings, and operating

instructions are clearly posted near each unit to insureproper operation, reduce the chance of

personal injury and/or equipment damage.

!WARNING: If service is required on this unit, contact your authorized APW Wyott Service Agent, or

contact the APW Wyott Service Department directly at (214) 421-7366 or (800) 527-2100; fax (214)

565-0976.

WARNING: Unit is not waterproof. DO NOT submerge in water. Do not operate if it has been

submerged in water. Do not clean the unit with a water jet.

!WARNING: To avoid any injury, turn the power switch off at the fuse disconnect switch/circuit

breaker or unplug the unit from the power source and allow to cool completely before performing

any maintenance or cleaning.

WARNING: To avoid electrical shock, always unplug the unit before performing cleaning or

maintenance.

WARNING: Neglecting to keep the fan opening clean could result in toaster failure.

WARNING: Operating the toaster without the Reflector Tray reduces the toasting capabilities.

WARNING: For safe and proper operation, the unit must be located a reasonable distance from

combustible walls and materials. If safe distances are not maintained, discoloration or combustion

could occur.

WARNING: To avoid electrical shock or personal injury, do not steam clean or use excessive water

on the unit.

WARNING: Do not allow untrained personnel to operate the toaster.

!WARNING: This product has no “user” serviceable parts. To avoid damage to the unit or injury to

personnel, use only Authorized APW Wyott Service Agents and genuine APW Wyott Parts when

service is required..

!CAUTION: Some exterior surfaces on the unit will get hot. Use caution when touching these areas

to avoid injury.

!CAUTION: Use only non-abrasive cleaners. Abrasive cleaners could scratch the finish of your unit,

marring it’s appearance and making it susceptible to dirt accumulation.

!NOTICE: Do not use toppings (butter, etc.) on product as product is inverted during normal

operation.

!WARNING: Operating toaster without legs invalidates any warranty claims.

!WARNING: Neglecting to keep fan opening clean could result in toaster failure.

!WARNING: In Europe, appliance must be connected by an earthing cable to all other units

in the complete installation and thence to an independent earth connection in compliance

with EN 60335-1 and/or local codes

WARNING: An earthing cable must connect the appliance to all other units in the complete

installation and from there to an independent earth connection.

GENERAL INFORMATION

I. Consult the rating label for model and serial number. Write this information below before

proceeding:

A. Model # __________________ B. Serial # __________________

II. Overall Dimensions w/Wire Feeder - 14.6" H (371mm) x 16.2" W (411 mm) x 26.5" 0 (674mm)

III. Product Opening - 1.5" H (38mm) x 10.50" W (267mm)

IV. Productivity (per hour) - results will vary depending on line voltage and bread dryness.

V. Electrical Requirements

A. Single phase, 208-240 volts, 3330 watts, 15.9 amps.

B. Cordset configuration

1. Each toaster is equipped with a three-wire grounded cordset and standard three-prong

plug.

2. In the United States, a four foot cordset with NEMA 6-20P plug.

3. In Canada, a six foot cordset with NEMA 6-20P plug.

Net/Shipping Weight - 48Ib.(21.8kg) /56Ib.(25.5kg)

INSTALLATION INSTRUCTIONS

I. Check Contents - refer to Figure 1, account for the following parts:

A. Toast Drawer - shipped in place

B. Reflector Tray - shipped in place

C. Wire Feeder - inside Reflector Tray

D. Instruction Manual - shipped loose

NOTE: DO NOT OPERATE THE TOASTER WITH THE REFLECTOR TRAY REMOVED FROM

ITS POSITION

II. Position Wire Feeder - refer to Figure 2

A. Pull out Reflector Tray

B. Rotate Wire Feeder

C. Slide Reflector Tray back

D. WARNING: Operating the toaster without the Reflector Tray reduces toasting capabilities.

WARNING: Genuine APW Wyott Replacement Parts are specified to operate safely in the

environments in which they are used. Some aftermarket or generic replacement parts do not have

the characteristics that will allow them to operate safely in APW Wyott equipment. It is essential to

use APW Wyott Replacement Parts when repairing APW Wyott equipment. Failure to use APW

Wyott Replacement Parts may subject operators of the equipment to hazardous electrical voltage,

resulting in electrical shock or burn.

CAUTION: Locate the unit at the proper counter height, in an area that is convenient for use. The

location should be level to prevent the unit or it’s contents from accidentally falling, and strong

enough to support the weight of the unit and food.

!CAUTION: The National Sanitation Foundation (NSF) requires that units over 36” (91 cm) in length

or weighing more than 80 lbs. (36 kg) to be either sealed or raised on the installation surface. If this

unit cannot be sealed at the point of use, 4” (10 cm) legs are included to allow for proper cleaning

access below unit.

!WARNING: Failure to provide clearances will cause unit failure and invalidate warranty claims

(see installation instructions).

figure 2

III. Toaster Placement

A. Locate the toaster near a grounded receptacle of the proper configuration (see below). Plug

the cordset directly into receptacle (DO NOT USE AN EXTENSION CORD).

1. In the United States, NEMA 6-20R.

2. In Canada, NEMA 6-20R.

B. Place the toaster on a flat surface providing the following minimum clearances:

1. Base = one inch (provided with legs installed).

2. Side and back walls = one inch

3. Overhead = Enough space to allow adequate heat displacement.

4. WARNING: Failure to provide these clearances will cause unit failure and invalidate

warranty claims.

C. Position toaster where customers will not contact any surface labeled "CAUTION HOT".

NOTE: DO NOT OPERATE THE TOASTER WITH THE LEGS REMOVED.

OPERATION INSTRUCTIONS

I. PREPARATION

A. Clean the toaster thoroughly before first use (See cleaning instructions).

B. Controls Familiarity

1. Main Power Switch - four (4) position rotary switch

a) Full Power: rotary switch turned RIGHT ( 3 o'clock). ( HIGH)

b) Power Off: rotary switch turned to TOP or BOTTOM. (12 and 6 o'clock) (OFF)

c) Standby Power: rotary switch turned LEFT (9 o'clock). ( STANDBY)

2. Conveyor Speed Control: Set knob to the five (5) position for warm-up.

C. Temperature Settings: Set both Top and Bottom heat knobs to 12 (max.) for warm up. One (1)

is the minimum heat setting. Power to the heating elements is off when the knobs are in the

OFF ( 0 ) position.

D. Warm-up time: Allow fifteen (15) minutes.

II. NORMAL USE

A. Loading Product

1. Place product on the Wire Feeder. The conveyor will automatically draw product through

the toaster at a speed determined by conveyor speed control.

B. Toasting Darkness: determined by conveyor speed.

1. Darkest toasting - set conveyor speed control to one (1).

2. Lightest toasting - set conveyor speed control to ten (10).

3. Other factors affecting toasting darkness.

a) Product moistness - moister product requires slower speeds

b) Sugar content in product - product with more sugar requires slower speeds

c) Product Temperature - cooler product requires slower speeds

4. For best results, use day old bread stored at room temperature.

C. The conveyor belt, drive motor, and shaft bearings do not require lubrication.

CLEANING INSTRUCTIONS

NEVER CLEAN THE TOASTER BY IMMERSING IT IN WATER. DO NOT CLEAN WITH A WATER JET.

I. DAILY CLEANING

A. With the toaster ELEMENTS OFF and cool, turn the toaster ON and set conveyor speed to

four (4).

B. Using a plastic abrasive pad, wipe the conveyor belt in a back and forth motion (side-to-side)

motion to remove baked-on product. Wipe clean the conveyor belt in the same manner with a

hot, damp cloth.

C. Turn OFF the toaster.

D. Slide the reflector/crumb tray out of the toaster by pulling forward. Dispose of crumbs and

wash the tray in hot, soapy water. Dry the tray and place it back into the toaster.

E. Remove the bottom toast drawer from the toaster by sliding it out and lifting up. Dispose of

crumbs and wash the drawer in hot, soapy water. Wipe crumbs from inside the toaster with a

hot, damp cloth. Dry the drawer and place it back into the toaster.

F. Wipe the exterior surfaces of the toaster with a hot, damp cloth.

II. PERIODIC CLEANING

A. Conveyor Belt

1. Remove the conveyor belt from the toaster.

2. Use needle-nose pliers to bend a link to the inside until the hook clears the link above.

3. Repeat on the other side.

4. Pull the loosened links together and slide through the center-of-belt link.

5. Clean the belt thoroughly (See item 2 under "daily cleaning").

6. Install the conveyor belt by reversing the order of steps noted above (See item 1).

NOTE: DO NOT INSTALL BELT BACKWARDS OR UPSIDE DOWN. ALIGN LINKS

ACROSS SHAFT SPROCKET TEETH.

B. Cooling Intake Fan

1. Unplug and lay the toaster on its side.

2. Brush dirt and debris from the fan opening and fan guard.

3. WARNING: Neglecting to keep the fan-opening clean could result in toaster failure.

WARRANTY PROCEDURE

If warranty service is needed on your FASTRAC , follow these steps:

I. Identify the model and serial number from the rating label on your toaster.

II. Consult the enclosed directory, find the service agency nearest you, call the number listed or the 24-

hour toll free service hot line, 1-800-733-2203. If there is not a service agency listed for your area,

the parts distributor will provide service for your toaster.

III. To order parts consult the enclosed directory. The parts distributor is listed at the beginning of each

state listing. The parts distributors have a complete stock of parts for your toaster.

TROUBLESHOOTING

I. Always ask and check the following:

A. Is the unit connected to a live power source?

B. Check the circuit breaker.

C. Is power switch on?

D. Is the unit operating on proper voltage? (see rating label)

E. Is power cord damaged? If YES, replace ONLY with an IDENTICAL power cord.

II. If problems exist after checking the above, check the chart below.

III. If any service is needed (italicized items), call an APW Wyott authorized service agency. All service

should be performed by an APW Wyott authorized service agency.

THE PROBLEM THE CAUSE THE SOLUTION

Won't toast... a. Toaster cold. a. Allow five (5) minutes for warm up.

b. Wrong power switch position. b. Position power switch to full power.

c. Wrong conveyor speed setting. c. Reduce conveyor speed.

Toasts unevenly... d. Only part of product surface is d. Reduce conveyor speed.

Toasted.

e. Product located too far to side of e. Place product on conveyor between

conveyor. end links.

Product sticks to f. Butter or butter substitute used on f. Discontinue use of butter or butter

conveyor or slide.. product. substitute.

g. Conveyor surface has baked-on oil g. Follow daily cleaning methods to

residue. remove & prevent residue.

h. Very moist or doughy product. h. Use different source or day-old

product.

i. Product not defrosted or thawed. i. Defrost/thaw product.

No power... j. No power to receptacle. j. Check circuit breaker.

k. Toaster unplugged. k. Plug in toaster.

I. Loose connections. I. Check connections.

m. Power switch. m. Check that switch is on &

operational.

Won't heat... n. Loose connections. n. Check connections.

o. Faulty power switch. o. Replace power switch.

p. Burnt out element. p. Replace element.

Lighter toast q. Speed control setting. q. Reduce speed control setting.

Under peak loads. r. Very moist product. r. Use different source or day old

product.

s. Product too cold. s. Allow product to warm to room

temperature.

t. Toaster cavity temperature being t. Add 1" or more spacing between

quenched. product.

Conveyor won't u. No power. u. Check circuit breaker.

move... v. Conveyor links are binding. v. Check conveyor for bent links.

w. Drive chain too loose or too w. Adjust drive chain.

tight.

x. Loose or bad connection x. Check for loose or bad

between speed control and connection.

conveyor motor.

y. Conveyor motor burnt out. y. Replace conveyor motor.

z. Speed control burnt out. z. Replace speed control.

TROUBLESHOOTING CHART:

ITEM P/N DESCRIPTION QTY

1 34236 TERMINAL BLOCK END MTG 1

2 34237 TERMINAL BLOCK (6) .250 MALE 3

3 38254 IDLER SHAFT ASSY 1

4 83956 DRIVE SHAFT ASSY 2

5 38278 CRUMB TRA Y/REFLECTOR ASSY 1

6 38129 TOAST DRAWER 1

7 38131 WIRE FEEDER 1

8 54095 ELEMENT 208V 1625W 2

54096 ELEMENT 240V 1625W 2

9 58188 LABEL, CONTROL PANEL 1

10 89490 SWITCH, MAIN ROTARY 1

11 82903 #25 DRIVE CHAIN, " PITCH, 65 PITCHES 1

12 PS0029 WIRE BELT, 3 SEGMENT, 3.07' OF 82920 (82 LINKS) 1

13 83248 BEARING SHAFT 2

14 83222 RHEOSTAT 208/240V TERM. 1

15 69104 INFINITE CONTROL 208V 15AMP CURVE "B" 2

69103 INFINITE CONTROL 240V 15AMP CURVE "B" 2

16 83261 DRIVEN SPROCKET, #25B12 TOOTH X 3/8" BORE (1/4" PITCH) 1

17 83260 DRIVE SPROCKET, #25B18 TOOTH X5/16" BORE (1/4" PITCH) 1

18 83277 POWER CORD 208-240V, 20 AMP PLUG 1

19 83267 LEG 1" CHROMED PLASTIC 4

20 38125 BEARING, FLANGED, POLYMER 2

21 85143 MOTOR, 230V 60HZ, 9RPM 1

22 85284 COOLING FAN 1

23 85288 FAN CORD 1

24 88705 KNOB 4

25 89111 STRAIN RELIEF 1

26 38247 WIRE GUARD 1

27 85287 FAN GUARD 1

28 69154 FAN CONTROL THERMOSTAT 1

REPLACEMENT PARTS LIST - FT 1000

EXPLODED VIEW - FT 1000

910 16

26 624

223

WIRING DIAGRAM - MODEL FT 1000

!IMPORTANT NOTICE: The information contained in this section of the manual is

intended for individuals possessing backgrounds of electrical and mechanical

experience, such as an authorized APW Wyott service technician. APW or the seller

cannot be responsible for the interpretation of this information, nor can it assume any

liability in connection with its use.

APW WYOTT EQUIPMENT LIMITED WARRANTY

APW Wyott Foodservice Equipment Company warrants it's equipment against defects in materials and workmanship, subject to the

following conditions:

This warranty applies to the original owner only and is not assignable.

Should any product fail to function in its intended manner under normal use within the limits defined in this warranty, at the option of

APW Wyott such product will be repaired or replaced by APW Wyott or its Authorized Service Agency. APW Wyott will only be

responsible for charges incurred or service performed by its Authorized Service Agencies. The use of other than APW Wyott

Authorized Service Agencies will void this warranty and APW Wyott will not be responsible for such work or any charges associated

with same. The closest APW Wyott Authorized Service Agent must be used.

This warranty covers products shipped into the 48 contiguous United States, Hawaii, metropolitan areas of Alaska and Canada. There

will be no labor coverage for equipment located on any island not connected by roadway to the mainland.

Warranty coverage on products used outside the 48 contiguous United States, Hawaii, and metropolitan areas of Alaska and Canada

may vary. Contact the international APW Wyott distributor, dealer, or service agency for details.

Time Period

One year for parts and one year for labor, effective from the date of purchase by the original owner. The Authorized Service Agency

may, at their option, require proof of purchase. Parts replaced under this warranty are warranted for the un-expired portion of the

original product warranty only.

Exceptions

*Gas/Electric Cookline: Models GCB, GCRB, GF, GGM, GGT, CHP-H, EF, EG, EHP. Three (3) Year Warranty on all

component parts, except switches and thermostats. (2 additional years on parts only. No labor on second or third year.)

*Broiler Briquettes,

*Heat Strips: Models FD, FDL, FDD, FDDL. Two (2) Year Warranty on element only. No labor second year.

*Glass Windows, Doors, Seals, Rubber Seals, Light Bulbs:

In all cases, parts covered by extended warranty will be shipped FOB the factory after the first year.

Portable Carry In Products

Equipment weighing over 70 pounds or permanently installed will be serviced on-site as per the terms of this warranty. Equipment

weighing 70 pounds or under, and which is not permanently installed, i.e. with cord and plug, is considered portable and is subject to

the following warranty handling limitations. If portable equipment fails to operate in its intended manner on the first day of

connection, or use, at APW Wyott's option or its Authorized Service Agency, it will be serviced on site or replaced.

From day two through the conclusion of this warranty period, portable units must be taken to or sent prepaid to the APW Wyott

Authorized Service Agency for in-warranty repairs. No mileage or travel charges are allowed on portable units after the first day of use.

If the customer wants on-site service, they may receive same by paying the travel and mileage charges. Exceptions to this rule: (1)

countertop warmers and cookers, which are covered under the Enhanced Warranty Program, and (2) toasters or rollergrills which have

in store service.

Exclusions

The following conditions are not covered by warranty:

*Equipment failure relating to improper installation, improper utility connection or supply and problems due to

ventilation.

*Equipment that has not been properly maintained, calibration of controls, adjustments, damage from improper cleaning

and water damage to controls.

*Equipment that has not been used in an appropriate manner, or has been subject to misuse or misapplication, neglect,

abuse, accident, alteration, negligence, damage during transit, delivery or installation, fire, flood, riot or act of god.

*Equipment that has the model number or serial number removed or altered.

If the equipment has been changed, altered, modified or repaired by other than an Authorized Service Agency during or after the

warranty period, then the manufacturer shall not be liable for any damages to any person or to any property, which may result from the

use of the equipment thereafter.

This warranty does not cover services performed at overtime or premium labor rates. Should service be required at times which

normally involve overtime or premium labor rates, the owner shall be charged for the difference between normal service rates and such

premium rates. APW Wyott does not assume any liability for extended delays in replacing or repairing any items beyond its control.

In all cases, the use of other than APW Wyott Authorized OEM Replacement Parts will void this warranty.

This equipment is intended for commercial use only. Warranty is void if equipment is installed in other than commercial application.

Water Quality Requirements

Water supply intended for a unit that has in excess of 3.0 grains of hardness per gallon (GPG) must be treated or softened before

being used. Water containing over 3.0 GPG will decrease the efficiency and reduce the operation life of the unit.

Note: Product failure caused by liming or sediment buildup is not covered under warranty.

“THE FOREGOING WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED

INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSES

AND CONSTITUTES THE ENTIRE LIABILITY OF APW WYOTT. IN NO EVENT DOES THE LIMITED WARRANTY

EXTEND BEYOND THE TERMS STATED HEREIN.”

9/05

Rock Grates, Cooking Grates, Burner Shields, Fireboxes: 90 Day Material Only. No Labor.

90 Day Material Only. No Labor.