Arcade Airline Pilot Manual User

APC-manual APC-manual

2013-11-07

User Manual: Arcade Airline Pilot Manual

Open the PDF directly: View PDF .
Page Count: 97

Download
Open PDF In Browser	View PDF

1st PRINTING MAY 00

STD TYPE

OWNER’S MANUAL

SEGA ENTERPRISES, INC. USA
MANUAL NO. 4200-6479-01

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies
that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control
Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.
Sellers sole liability in the event a warranted part described above fails shall be, at its option, to
replace or repair the defective part during the warranty period. For Warranty claims, contact your
Sega Distributor.
Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.
Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other
warranties expressed or implied. Under no circumstance shall it extend beyond the period of time
listed above.

TABLE OF CONTENTS

INTRODUCTION OF THE OWNERS MANUAL
GENERAL PRECAUTIONS
1. PRECAUTIONS TO BE HEEDED FOR OPERATION
2. NAME OF PARTS
3. ACCESSORIES
4. ASSEMBLY AND INSTALLATION
5. PRECAUTIONS TO BE HEEDED WHEN MOVING MACHINE
6. CONTENTS OF GAME
7. EXPLANATION OF TEST AND DATA DISPLAY
7-1 SWITCH UNIT AND COIN METER
7-2 SYSTEM TEST MODE
A C.R.T. TEST
B COIN ASSIGNMENTS
7-3 GAME TEST MODE
A INPUT TEST
B OUTPUT TEST
C SOUND TEST
D C.R.T. TEST
E GAME ASSIGNMENTS
F VOLUME SETTING
G BOOKKEEPING
H BACKUP DATA CLEAR
8. CONTROL MECHA
8-1 REMOVING THE CONTROL MECHANISM
8-2 ADJUSTING THE VOLUME
8-3 REPLACING THE VOLUME
8-4 GREASING
8-5 REPLACING THE SWITCH LEVER
9. LEVER UNIT
9-1 ADJUSTING THE VOLUME
9-2 REPLACING THE VOLUME
9-3 GREASING
10. PEDAL UNIT
10-1 ADJUSTING THE VOLUME
10-2 REPLACING THE VOLUME
10-3 GREASING
11. COIN SELECTOR
12. MONITOR
12-1 CAUTIONS/WARNINGS FOR HANDLING
12-2 CAUTIONS TO BE HEEDED WHEN CLEANING
12-3 ADJUSTMENT METHOD
13. REPLACING THE FLUORESCENT LAMP
14. PERIODIC INSPECTION TABLE
15. TROUBLESHOOTING
16. GAME BOARD
16-1 LOCATING THE GAME BOARD
16-3 COMPOSITION OF THE GAME BOARD
18. DESIGN RELATED PARTS
19. PARTS LIST
20. WIRING DIAGRAMS

1
2~3
4~5
6
7~8
9~16
17
18~20
21~34
22
23~29
24
25~29
30~34
31
31
32
32
33
33
34
34
35~38
35
36
36
37
38
39~40
39
40
40
41~42
41
42
42
43~45
46~48
46~47
47
48
49
50
51
52~53
52
53
54~55
56~92
XXX

SPECIFICATIONS
Installation space:

37.2 in.(W) x 64.0 in.(D)

Height:

73.6 in.

Weight:

Approx. 617.3 lbs.

Power maximum current:

2.3 Amp AC 120V 60 Hz

MONITOR:

29” COLOR MONITOR

INTRODUCTION OF THE OWNERS MANUAL
SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and
popular amusement products to the world market. This Owners Manual is intended to provide
detailed descriptions together with all the necessary installation, game settings and parts ordering
information related to AIRLINE PILOTS STD TYPE, a new SEGA product.
This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire
sufficient knowledge before working on the machine. Should there be a malfunction, non-technical
personnel should under no circumstances touch the interior system. Should the need arise, contact
our main office, or the closest branch office listed below.

SEGA ENTERPRISES, INC. (USA)
Customer Service
45133 Industrial Drive
Fremont, CA 94538
Phone 415-701-6580
Fax
415-701-6594
7:30 am - 4:00 pm, Pacific Standard Time
Monday thru Friday

General Precautions

Follow Instructions: All operating and use instructions should be followed.
Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards.
Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the
manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer.
Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces
may cause the product to overturn.
Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product
and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked
by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
Power Sources: This product should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supply to your location, consult your local power company. For products intended
to operate from battery power or other sources, refer to the operating instructions.
Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third
(grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the
grounding-type plug.
Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the product.
Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in
a risk of fire or electric shock.
Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the
product.
Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a) If the power cord or plug is damaged;
b) If liquid has been spilled, or objects have fallen into the product;
c) If the product has been exposed to rain or water;
d) If the product does not operate normally when following the operating instructions. Adjust only those controls that
are explained in the operating instructions. An improper adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore the product to its normal operation;
e) If the product has been dropped or damaged in any way;
f) When the product exhibits a distinct change in performance; this indicates a need for service.
Replacement Parts: When replacement parts are required, be sure the service technician has used replacements parts
specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards.

Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’s recommendations.
Do not dispose in an open flame condition, since the battery may explode.
Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such
as benzine, thinner, etc.
Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors
in the places mentioned below:
• Places subject to rain/water leakage, or condensation due to humidity;
• In close proximity to a potential wet area;
• Locations receiving direct sunlight;
• Places close to heating units or hot air;
•In the vicinity of highly inflammable/volatile chemicals or hazardous matter;
• On sloped surfaces;
• In the vicinity of emergency response facilities such as fire exits and fire extinguishers;
• Places subject to any type of violent impact;
• Dusty places.
INSTALLATION PRECAUTIONS
• Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.
• Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG
rated min. 120 VAC, 7A.
• Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H).
• For the operation of this machine, secure a minimum area of 32” (W) by 42”(D).
REGULATORY APPROVALS
This game has been tested and found to comply with the Federal Communications Commission Rules.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.

1 . PRECAUTIONS TO BE HEEDED FOR OPERATION
In order to prevent accidents, be sure to comply with the following points before and during operation.

PRECAUTIONS TO BE HEEDED FOR OPERATION BEFORE STARTING THE OPERATION
In order to avoid accidents, check the following before starting the operation:
Check if all of the adjusters are in contact with the surface. If they are not,
the cabinet can move and cause an accident.

Do not climb on the product. Climbing on the product can cause falling
down accidents. To check the top portion of the product, use a step.
To avoid electric shock, check to see if door & cover parts are closed.
To avoid electric shock, short circuit and or parts damage, do not put the
following items on or in the periphery of the product:
Flower vases, flower pots, cups, water tanks, cosmetics, and receptacles/
containers/vessels containing chemicals and water.

To avoid injury, be sure to provide sufficient space by considering the
potentially crowded situation at the installation location. Insufficient installation space can cause the player to come into contact with or hit others
and result in injury or trouble.

PRECAUTIONS TO BE HEEDED DURING OPERATION
To avoid injury and accidents, those who fall under the following catagories are not
allowed to play the game:
* Intoxicated persons
* Those who have high blood pressure or heart problems.
* Those who have experienced muscle convulsion or loss of consciousness when
playing video games, etc.
* Persons susceptible to motion sickness.
* Persons whose acts runs counter to the products warning displays.
* Instruct those who wear high-heeled shoes to refrain from
playing the game by explaining that playing the game with highheeled shoes is very dangerous and likely to cause a potentially
hazardous situation.
To avoid electric shock and short circuit, do not allow customers to put hands and
fingers or extraneous matter in openings of the product or small openings in or around
doors.
To avoid electric shock and short circuit, do not allow the customers to unplug the
power plug without a justifiable reason.
Although this product has the accident preventive covering attached to potentially
hazardous places where hand and fingers could be caught, small children are unable to
perceive hazards. Use care so that small children do not come close to the product when
in play.
Immediately stop such violent acts as hitting and kicking the product. Such violent acts
can cause parts damage and/or falling down, resulting in injury due to fragments and
falling down.

2 . NAME OF PARTS

GAME SPECIFICATIONS

WIDTH in.

LENGTH in.

HEIGHT in.

WEIGHT lbs.

All measurements are and rounded UP
DURING SHIPPING
WHEN ASSEMBLED

42”

60”

65”

669 LBS.

37.25”

64”

73.75”

619 LBS.

3 . ACCESSORIES

THE SHIPMENT METHOD DESCRIBED BELOW ONLY
APPLIES TO ‘MODEL 3’ BOARDS CONTAINED IN THE
FOLLOWING GAMES:
LOST WORLD, VIRTUA FIGHTER 3, SUPER GT, SEGA BASS FISHING, STRIKER 2
HARLEY DAVIDSON, RALLY 2, DAYTONA 2, DIRT DEVILS, HOUSE OF THE DEAD
2, OCEAN HUNTER, STAR WARS TRILOGY, ZOMBIE REVENGE, CRAZY TAXI,
ARILINE PILOTS

!!NEVER SHIP MODEL 3 / NAOMI GAME
BOARDS OUTSIDE OF CAGE!!
CARTON BOX
601-8928 (1)
Used for transporting the GAME BOARD.
{SUPPLIED WITH YOUR GAME}

DO NOT SHIP GAME BOARD WITHOUT
THIS BOX AS IT MAY DAMAGE THE GAME
BOARD AND VOID YOUR WARRANTY.

“CHECK SIDE” Display

FILTER BOARD

NO OTHER GAMES BOARDS ARE TO BE SHIPPED IN THE CAGE AS
THEY MAY BE DAMAGED BEYOND REPAIR. PLEASE SHIP THEM
WITHOUT CAGE PROPERLY PROTECTED DURING SHIPPING.

4 . ASSEMBLING AND INSTALLATION
-Assembling should be performed as per this manual. Since this is a
complex machine, erroneous assembling may cause damage to the
machine, or malfunctioning to occur.
-When assembling, be sure to perform work by plural persons.
Depending on the assembly work, there are some cases in which
performing the work by a single person can cause personal injury or
parts damage.
-Be careful so as not to damage wirings. Damaged wiring can cause
electric shock and short circuit hazards.

When carrying out the assembly work, follow the procedure in the following 5-item sequence:

ASSY OF BILLBOARD

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

POWER SUPPLY

ASSEMBLING CHECK

Note that the tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width
across flats are required for the assembly work.

ASSY OF BILLBOARD

Due to its large size, it is very difficult for one person alone to install the billboard,
Make sure 2 or more persons are available to perform this work. Attempting to
perform the installation alone can cause an accident.

Take out the 2 screws, and
remove the Plate Holder &
Billboard Plate.

2 From the rear of the Billboard,
remove the 2 Bolt Lids and
the Connector Lid by taking
out 2 screws from each

3 Loosen the 2 Bolts securing
the Billboard Hook.

Mount the Billboard by hanging
on the Billboard Hook, secure
the Billboard with 2 Bolts
through the square holes of Bolt
Lids previously removed, and
connect the Connector.

Install the 2 Bolt Lids and
Connector Lid.

Insert the Billboard Holder in
place so as to fit the bolt
positions, and fasten the bolts
to secure the Billboard.

Install the Billboard Plate by
using the procedure opposite 1
above

Apply the oblique line portion
of the POP PANEL to the upper
rear part of the Billboard. At this
time, ensure that the POP does
not disappear.

SECURING IN PLACE (ADJUSTER ADJUSTMENT)
Be sure to have all the Adjusters make contact with the floor surface.
Unless the Adjusters come into contact with the floor surface, the
Cabinet can move of itself, causing an accident.

This machine has 4 each of casters and adjusters (shown below). When the installation position is determined, cause
the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be
raised approximately 5mm. from the floor and make sure that the machine position is level.

Move the machine to the installation position,
making sure to provide adequate space for the
player to get on and off.

Cause all of the leg levelers to make contact
with the floor. By using a wrench, make
adjustments in the height of the leg adjusters to
ensure that the machine's position is kept level.

After making adjustments, fasten the leg
adjuster nut upward and secure the height of the
leg adjuster.

Permanantly tightening the hex bolts should not be completed until
the leg levelers are adjusted properly.

POWER SUPPLY

Ensure that the power cord is not exposed on the surface (passage,
etc.). If exposed, they can be caught and are susceptible to damage.
If damaged, the cord can cause an electric shock or short circuit.
Ensure that the wiring position is not in the customer's passage way
or the wiring has protective covering.

Connect the game to the power supply and turn on power to the game. Before connecting power supply be sure that
power switch is off

Turning the AC unit’s main switch on will cause the machine
to start the power check and network check automatically.

2 In the Power On check, the steering wheel turns left and right,
and then returns to the centering position and stops. In this
check, the values of the VR inside the control panel are
corrected.

3 Until this check is finished, and the steering wheel stops, do
not touch the steering wheel or play the game.
If you do, the steering reaction during the game (reaction at
the time of course-out or crash) can not be obtained correctly.
In the case of an abnormal reaction during the game, turn
power on again from the beginning and complete the power on
check.

ASSEMBLING CHECK

The TEST MENU allows for each part of the cabinet to be checked, the Monitor to be adjusted, and the coin and game
related various functions to be performed.
In the TEST MODE, ascertain that the assembly has been made correctly and that the IC BOARD is satisfactory.
In the test mode, perform the following test:

(1) MEMORY TEST
RAM TEST

IC29
IC35
IC16
IC20
IC09
IC11

GOOD
GOOD
GOOD
GOOD
GOOD
GOOD

IC18
IC22
IC10
IC12

Selecting the RAM TEST and ROM TEST on
the test mode menu screen causes the onboard memory to be tested automatically.
The game board is satisfactory if the display
beside each IC No. shows GOOD.
GOOD
GOOD
GOOD
GOOD

PRESS TEST BUTTON TO EXIT

ROM BOARD TEST
[AIRLINE PILOTS IN XXXX]
NO. TYPE
IC22 32M
IC1
64M
IC2
64M
IC3
64M
IC4
64M
IC5
64M
IC6
64M
IC7
64M
IC8
64M
IC9
64M
IC10 64M
IC11 64M

RESULT
---GOOD
GOOD
GOOD
GOOD
GOOD
GOOD
GOOD
GOOD
GOOD
GOOD
GOOD

BYTE WORD
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX
XXXX XXXX

PRESS TEST BUTTON TO EXIT

(2) C.R.T. TEST
In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the monitor is tested) to be
displayed. Although the monitor adjustments have been made at the time of shipment from the factory, color
deviation, etc., may occur due to the effects of geomagnetism, the location of the building’s steel frames and
other game machines in the periphery. By watching the test mode screen, make judgement as to whether an
adjustment is needed. If it is neccessary, adjust the projector by refering to Section 7.

In the C.R.T. test of SYSTEM TEST mode, adjust color and screen size.
In the C.R.T. test of GAME TEST mode, adjust monitor brightness.

SYSTEM TEST mode
C.R.T. TEST 2/2

C.R.T. TEST 1/2
1

RED

GREEN

BLUE

WHITE

PRESS TEST BUTTON TO CONTINUE

GAME TEST mode
C.R.T. TEST

PRESS TEST BUTTON TO EXIT

(3) INPUT TEST
INPUT TEST
LANDING GEAR SWITCH
FLAP SWITCH
VIEW CHANGE BUTTON
START BUTTON
SERVICE
TEST
CONTROL WHEEL (AILERON)
CONTROL WHEEL (ELEVATOR)
RUDDER PEDAL
THRUST LEVER L
THRUST LEVER R

UP
UP
OFF
OFF
OFF
OFF
ABH
ABH
ABH
ABH
ABH

Selecting the INPUT TEST on the game test mode
menu screen carses the screen (on which each switch
and V.R. are tested) to be displayed. Press each switch.
If the display beside each switch indicates “ON,” the
switch and wiring connections are satisfactory.

PRESS TEST AND SERVICE BUTTON TO EXIT

(4) OUTPUT TEST
OUTPUT TEST
START BUTTON LAMP
LANDING GEAR UP LAMP
LANDING GEAR DOWN LAMP
FLAP UP LAMP
FLAP DOWN LAMP
VIEW CHANGE BUTTON LAMP

OFF
OFF
OFF
OFF
OFF
OFF

Select OUTPUT TEST from the menu in the game test
mode to cause the screen (on which each lamp is tested)
to appear. Ensure that each lamp lights up satisfactorily.

->EXIT
SELECT WITH SERVICE BUTTON AND PRESS
TEST BUTTON

(5) SOUND TEST
SOUND

TEST

No. 0

In the TEST mode, selecting SOUND TEST causes the
screen, on which sound related BD and wiring connections are tested, to be displayed. Be sure to check if the
sound is satisfactorily emitted from each speaker and
that the sound volume is appropriate.

SELECT WITH SERVICE BUTTON AND PRESS
TEST BUTTON TO EXIT

Perform the above inspections also at the time of monthly inspection.

5 . PRECATIONS TO BE HEEDED WHEN MOVING THE MACHINE
When moving the machine, be sure to pull out the plug from the
power supply. Moving the machine with the plug inserted can damage
the power cord and cause a fire or electric shock.
When moving the machine on the floor, retract the Adjusters and
ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords.
Damaging the power cords can cause an electric shock and/or short
circuit.
When lifting the cabinet, be sure to hold the catch portions or bottom
part. Lifting the cabinet by holding other portions can damage parts
and installation portions, due to the empty weight of the cabinet, and
cause personal injury.
When lifting the machine, do not push the cabinet from the left/right
direction. Doing so can cause the cabinet to fall down, resulting in
personal injury and or parts damage.
Use care when handling glass made parts. When the glass is damaged,
fragments of glass can cause injury

6 . CONTENTS OF GAME
The following explanations apply in the event the product is functioning satisfactorily. Should there be any moves
different from the following contents, some sort of faults may have occured. Immediately look into the cause of the
fault and eliminate the cause thereof to ensure satisfactory operation.

SEGA LOGO

TITLE

GAME MODE

Returns to the beginning

♦From GAME START up to the end of SELECT.
Insert a credit worth a number of coins. Up to 9 credits can be counted at a time. Coins inserted after counting 9 credits
are neither counted as credits nor returned. However, those coins inserted after counting 9 credits are included in the data
display or coin meter as number of coins inserted

Press the START button to start.
When the GAME MODE select screen
appears, select TRAINING mode or
FLIGHT mode.
-Incline the CONTROL WHEEL left
or right to select and press the START
button to confirm the selection
(hereafter, this method applies to any
selection).

•When the CONTROL SYSTEM select
screen appears, select AUTO CONTROL
or FULL CONTROL.
•In the AUTO CONTROL, only the
CONTROL WHEEL and the RUDDER
PEDAL are operated by the player. The
FLAP SW, LANDING GEAR SW, and
THRUST LEVER are automatically
controlled.
•In the AUTO CONTROL, Control
Switches need not be set. The TRAINING
MODE game starts immediately.
•In the FULL CONTROL, the TRAINING mode game starts after setting Control Switches in accordance
with the on-screen instruction.
•In the FULL CONTROL, all Contollers are operated by the player.

-The FLIGHT COURSE select mode appears
on the screen. Select one from among
BEGINNER, INTERMEDIATE, and
EXPERT.
-The specific flight course of BEGINNER,
INTERMEDIATE, and EXPERT corresponds to flight in the daytime, evening, and
nighttime respectively.
-When the CONTROL SYSTEM select screen
appears, select the CONTROL SYSTEM in the
similar manner as in the TRAINING MODE

♦HOW TO PLAY IN THE TRAINING MODE
•This mode has 5 Training items, i.e., taking-off, turning, landing, evading engine trouble, and bad weather.
•The qualifying score is predetermined for each training item. If the player is disqualified, CONTINUE? appears on
the screen.
•CONTINUE? appears on the screen also when nearing the end of flight time limit, deviating from the course and
crashing.
•When CONTINUEd, the game starts from the beginning of that particular training.
•When all of the training items are cleared, the total score will be displayed and the game is finished.

♦HOW TO PLAY IN FLIGHT MODE
•Take off from the airport and freely fly over Tokyo within the time limit.
•Passing near the Time Marker floating in the air increases the time limit.
•When nearing the time limit, select FLIGHT to continue flight for the remaining time or landing.
•Select FLIGHT to continue up to the end of the time limit. When time is up, CONTINUE? appears on the screen. If
CONTINUEd, flight can be continued again. When the LANDING MODE is selected, the on-screen scene changes
to the LANDING course. If the landing is successful, the game is finished. Failing to make a landing results in a

7 . EXPLANATION OF TEST AND DATA DISPLAY
By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or
collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations
given in this section. The following shows tests and modes that should be utilized as applicable.

CAUTIONS TO BE HEEDED WHEN USING THE TEST MODE:
In the case where plural machines are linked for communication play, if even one seat enters
the test mode, all of the linked seats will enter the test mode. Therefore, if any one of the
linked machines is in play, use care so as not to use the test mode.
The contents of the setting changes made will not be effective unless the test mode is
finished in the test mode. When the setting is changed, be sure to “EXIT” in the menu mode.
Do not press the TEST BUTTON during network check at the time of turning the power on or
exiting from the test mode. If anyone of the linked machines uses the test mode during
network check, all other Seats will continue network checking. Cause all of the Seats to
reenter the test mode and then have all of the Seats exit from the test mode simultaneously.

TABLE

EXPLANATION OF TEST MODE

ITEMS

DESCRIPTION

When the machine is installed, perform the following:
INSTALLATION 1. Check to see that each setting is as per the standard settings at the
time of shipment.
OF MACHINE
2. In the INPUT TEST mode, check each SW and VR.
3. In the OUTPUT TEST mode, check each of lamps.
4. In the MEMORY TEST mode, check ICs on the IC Board.
MEMORY

PERIODIC
SERVICING

Choose MEMORY TEST in the MENU mode to allow the
MEMORY test to be performed. In this test, PROGRAM
RAMs, ROMs, and ICs on the IC Board are checked.
Periodically perform the following:
1. MEMORY TEST
2. Ascertain each setting.
3. In the INPUT TEST mode, test the CONTROL device
4. In the OUTPUT TEST mode, check each of lamps.

SECTIONS
SERVICE MANUAL
7-3A
7-3B
4-4-1
SERVICE MANUAL
4-4-1

4-4-1
7-3A
7-3B

CONTROL
SYSTEM

1. In the INPUT TEST mode, check each SW and VR.
7-3A
2. Adjust or replace each SW and VR.
8,9,10
3. If the problem can not be solved yet, check the CONTROL’s moves.

MONITOR

In the MONITOR ADJUSTMENT mode, check to see if the
MONITOR adjustment is appropriately made.

12-3

IC BOARD

1. MEMORY TEST
2. In the SOUND TEST mode, check the sound related ROMs.

4-4-1
7-3C

DATA CHECK

Check such data as game play time and histogram to adjust the
difficulty level, etc

7-3E
7-3G

7 - 1 SWITCH UNIT AND COIN METER
Never touch places other than those specified. Touching places not
specified can cause electric shock and short circuit.

Adjust to the optimum sound volume by considering the environmental
requirements of the installation location.
If the COIN METER and the game board are electrically disconnected,
game play is not possible.

Open COIN CHUTE DOOR, and the switch unit shown appears. The function of
each switch is as follows:
SWITCH UNIT

SPEAKER VOLUME (VOLUME)
Controls the speaker volume for the right/left speakers.

SERVICE BUTTON (SERVICE SW)
Gives credits without registering on the coin meter.

TEST BUTTON (TEST SW)
For the handling of the TEST BUTTON, refer to the section on test mode.

DEMAGNETIZER SWITCH (DEMAGNETIZER SW)
Eliminates the on-screen color unevenness due to magnetization of CRT.
First use this SW before performing the monitor’s color adjustment.

COIN METER
Open the Cashbox Door by using the key to
have the Coin Meter appear underneath the
Cashbox.

7 - 2 SYSTEM TEST MODE
•The contents of settings changed in the TEST mode are stored when the TEST
mode is finished from EXIT in the MENU mode. If the power is turned off before the
TEST mode is finished, the contents of the setting changes do not take effect.
•Executing “BACKUP DATA CLEAR” in the SYSTEM TEST MODE does not clear the
BOOKKEEPING data in the GAME TEST MODE.
•Entering the TEST mode clears fractional numbers of coins less than one credit and
BONUS ADDER data.
The SYSTEM TEST mode mainly allows checks of the IC Board for accurate functioning , monitor adjustment, as well
as CRT TEST and COIN ASSIGNMENTS, etc. The following assignments, however, should be designated for this
product.

♦ CABINET TYPE
: 1 PLAYER (S)
♦ MONITOR TYPE
: HORIZONTAL
♦ COIN CHUTE TYPE : COMMON

TEST ITEM SELECT

SYSTEM MENU
RAM TEST
JVS TEST
SOUND TEST
C.R.T. TEST
SYSTEM ASSIGNMENTS
COIN ASSIGNMENTS
BOOKKEEPING
BACKUP DATA CLEAR
CLOCK SETTING
ROM BOARD TEST
GAME TEST MODE
[X X X X X X X X X X X]
EXIT
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

1 After turning the power on, press the TEST button to display the test item menu shown above.
2 Press the SERVICE button to move the arrow to the desired item and press the TEST button.
3 When finished, bring the arrow to EXIT and press the TEST button to return to the Game mode.

A C.R.T. TEST

1) RGB COLOR ADJUSTMENT SCREEN
In this screen, monitor color can be checked.
C.R.T. TEST 1/2
1

RED

GREEN

Each of red, green, and blue is the darkest at the
leftmost end, and becomes brighter towards the
right-hand end in 31 gradiations. Monitor brightness
is satisfactory if the white color bar is black at the
left end and if it is white at the right end.
Press the TEST button to proceed to the next screen.

BLUE

WHITE

PRESS TEST BUTTON TO CONTINUE

2) MONITOR SIZE ADJUSTMENT SCREEN
In this screen, monitor size can be checked.
C.R.T. TEST 2/2

PRESS TEST BUTTON TO EXIT

Adjust the crosshatch frame line so that the checkered pattern does not extend beyond the screen.
Press the TEST button to return to the menu mode.

B COIN ASSIGNMENTS
The “COIN ASSIGNMENTS” mode permits you to set the start number of credits, as well as the basic numbers
of coins and credits. This mode expresses “how many coins correspond to how many credits.”

SETTING CHANGE PROCEDURE

Setting changes cannot be stored unless the TEST BUTTON is pressed
while the arrow is on EXIT.

Press the SERVICE BUTTON to move the arrow to the desired item.

Change the desired item setting by using the TEST BUTTON.

To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

COIN ASSIGNMENTS
COIN CHUTE TYPE
COIN/CREDIT SETTING
COIN CHUTE #1
1 COIN 1 CREDIT

COMMON
#1

(A)
(B)

COIN CHUTE #2
1 COIN 1 CREDIT
MANUAL SETTING
SEQUENCE SETTING
-> EXIT

SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

(COMMON SETTING)

(A) COIN CHUTE TYPE (COMMON, INDIVIDUAL)
Set to COMMON.
Up to 2 Coin Chutes (#1 and #2) can be used and also, (B) COIN/CREDIT SETTING ratio can be set seperately
for #1 and #2.
(B) COIN/CREDIT SETTING (#1 ~ #27)
Sets the credit increase increment per coin insertion. There are 27 settings from #1 to #27, expressed in
credit(s) as against
coins inserted. #27 refers to FREE PLAY.

(C) MANUAL SETTING
The Credit’s incremental increase settings as against a coin insertion are shown in further details
than in (B) above (refer to Table 2). Also, note that when this MANUAL SETTING is performed,
(B) COIN CREDIT setting becomes ineffective.

MANUAL SETTING
COIN ASSIGNMENTS
MANUAL SETTING
COIN TO CREDIT
1
BONUS ADDER
NO BONUS ADDER
COIN CHUTE #1 MULTIPLIER
1 COIN COUNT AS 1 COIN
COIN
1 2 3 4 5 6 7 8 9
CREDIT 1 2 3 4 5 6 7 8 9

(D)
(E)
(F)

COIN CHUTE #2 MULTIPLIER
1 COIN COUNT AS 1 COIN
COIN
1 2 3 4 5 6 7 8 9
CREDIT 1 2 3 4 5 6 7 8 9

(F)

SEQUENCE SETTING

(G)

-> EXIT
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

(D) COIN TO CREDIT
Determines COIN/CREDIT setting.
(E) BONUS ADDER
This sets how many coins should be inserted to obtain one SERVICE COIN.
(F) COIN CHUTE (#1/#2) MULTIPLIER
This sets how many tokens one coin represents.

Table 1: COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)
SETTING
SETTING #1
SETTING #2
SETTING #3
SETTING #4
SETTING #5
SETTING #6
SETTING #7
SETTING #8
SETTING #9
SETTING #10
SETTING #11
SETTING #12
SETTING #13
SETTING #14
SETTING #15
SETTING #16
SETTING #17
SETTING #18
SETTING #19

SETTING #20
SETTING #21
SETTING #22
SETTING #23

SETTING #24
SETTING #25

SETTING #26
SETTING #27

FUNCTION OF CHUTE#1
1 COIN
1 CREDIT
1 COIN
2 CREDITS
1 COIN
3 CREDITS
1 COIN
4 CREDITS
1 COIN
5 CREDITS
1 COIN
2 CREDITS
1 COIN
5 CREDITS
1 COIN
3 CREDITS
1 COIN
4 CREDITS
1 COIN
5 CREDITS
1 COIN
6 CREDITS
2 COINS
1 CREDIT
1 COIN
1 CREDIT
1 COIN
2 CREDITS
1 COIN
1 CREDIT
2 COINS
3 CREDITS
1 COIN
3 CREDITS
3 COINS
1 CREDIT
4 COINS
1 CREDIT
1 COIN
1 CREDIT
2 COINS
2 CREDITS
3 COINS
3 CREDITS
4 COINS
5 CREDITS
1 COIN
5 CREDITS
5 COINS
1 CREDIT
1 COIN
2 CREDITS
2 COINS
1 CREDIT
4 COINS
2 CREDITS
5 COINS
3 CREDITS
1 COIN
3 CREDITS
1 COIN
1 CREDIT
2 COINS
2 CREDITS
3 COINS
3 CREDITS
4 COINS
4 CREDITS
5 COINS
6 CREDITS
1 COIN
1 CREDITS
FREE PLAY

Table 2: MANUAL SETTING

COIN TO CREDIT

1 COIN
2 COINS
3 COINS
4 COINS
5 COINS
6 COINS
7 COINS
8 COINS
9 COINS

1 CREDIT
1 CREDIT
1 CREDIT
1 CREDIT
1 CREDIT
1 CREDIT
1 CREDIT
1 CREDIT
1 CREDIT

BONUS ADDER

NO BONUS ADDER
2 COINS GIVE 1 EXTRA COIN
3 COINS GIVE 1 EXTRA COIN
4 COINS GIVE 1 EXTRA COIN
5 COINS GIVE 1 EXTRA COIN
6 COINS GIVE 1 EXTRA COIN
7 COINS GIVE 1 EXTRA COIN
8 COINS GIVE 1 EXTRA COIN
9 COINS GIVE 1 EXTRA COIN

COIN CHUTE (#1/#2)
MULTIPLIER

1
1
1
1
1
1
1
1
1

COIN COUNTS AS
COIN COUNTS AS
COIN COUNTS AS
COIN COUNTS AS
COIN COUNTS AS
COIN COUNTS AS
COIN COUNTS AS
COIN COUNTS AS
COIN COUNTS AS

1
2
3
4
5
6
7
8
9

COIN
COINS
COINS
COINS
COINS
COINS
COINS
COINS
COINS

(G) SEQUENCE SETTING
Number of credits required for starting a game, etc. can be set.
Each sequence can be set between 1 ~ 5 credit(s).

COIN ASSIGNMENTS
SEQUENCE SETTING
SEQUENCE 1
2 CREDIT(S)
SEQUENCE 2
1 CREDIT(S)
SEQUENCE 3
1 CREDIT(S)
SEQUENCE 4
1 CREDIT(S)
SEQUENCE 5
1 CREDIT(S)
SEQUENCE 6
1 CREDIT(S)
SEQUENCE 7
1 CREDIT(S)
SEQUENCE 8
1 CREDIT(S)
EXIT
[XXXXX XXXXX XXXXX XXXXX]
DESCRIPTION OF SEQUENCE
1 CREDIT TO START
2 CREDIT TO CONTINUE
3 NO USE
4 NO USE
5 NO USE
6 NO USE
7 NO USE
8 NO USE
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

SEQUENCE 1:
SEQUENCE 2:
SEQUENCE 3 ~ 8:

Number of credits required for game to start.
Number of credits required for CONTINUE.
NOT USED.

7 - 3 GAME TEST MODE
MENU MODE
SYSTEM MENU

AIRLINE PILOTS TEST MENU

RAM TEST
JVS TEST
SOUND TEST
C.R.T. TEST
SYSTEM ASSIGNMENTS
COIN ASSIGNMENTS
BOOKKEEPING
BACKUP DATA CLEAR
CLOCK SETTING

INPUT TEST
OUTPUT TEST
SOUND TEST
C.R.T. TEST
GAME ASSIGNMENTS
VOLUME SETTING
BOOKKEEP ING
BACKUP DATA CLEAR
-> EXIT

ROM BOARD TEST
-> GAME TEST MODE
[X X X X X X X X X X X]
EXIT
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

SYSTEM TEST MODE MENU

SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

GAME TEST MODE MENU

Press the TEST button to display the SYSTEM TEST MODE MENU.
By pressing the SERVICE button, move the arrow (->) to select the GAME TEST MODE.
Press the TEST button to enter GAME TEST MODE. The screen displays the GAME TEST MODE
MENU.
By pressing the SERVICE button, move the arrow (->) to select the desired item. Press the TEST button to
execute the selected item.
Select EXIT and press the TEST button to exit from the GAME TEST MODE and return to the SYSTEM
TEST MODE MENU. Further, select EXIT and press the TEST button to finish SYSTEM TEST MODE
and return to the normal mode.

A. INPUT TEST
Select INPUT TEST to have the screen shown below appear and to observe the status of each switch
and the value of each V.R. on the Control Panel. In this mode, Periodically check the status of each
switch and V.R.
INPUT TEST
LANDING GEAR SWITCH
FLAP SWITCH
VIEW CHANGE BUTTON
START BUTTON
SERVICE
TEST
CONTROL WHEEL (AILERON)
CONTROL WHEEL (ELEVATOR)
RUDDER PEDAL
THRUST LEVER L
THRUST LEVER R

UP
UP
OFF
OFF
OFF
OFF
ABH
ABH
ABH
ABH
ABH

PRESS TEST AND SERVICE BUTTON TO EXIT

By pressing each switch, if the display on the right-hand side
of the name of each switch changes to ON from OFF, the SW
and the wiring connections are satisfactory. UP and DOWN
are displayed for LANDING GEAR SWITCH and FLAP
SWITCH.
Operate CONTROL WHEEL, THRUST LEVER, etc. to
check Volume value display variation.
To check CHUTE 1 & CHUTE 2 coin switches, open the
COIN CHUTE DOOR and insert a coin(s) in the slot.
Simultaneously pressing the TEST BUTTON and the
SERVICE BUTTON returns to the test menu.

B. OUTPUT TEST
Select OUTPUT TEST to cause the following screen to appear, and allows the status of each lamp to
be checked. In this mode, periodically check the lamp status.
OUTPUT TEST
START BUTTON LAMP
LANDING GEAR UP LAMP
LANDING GEAR DOWN LAMP
FLAP UP LAMP
FLAP DOWN LAMP
VIEW CHANGE BUTTON LAMP

OFF
OFF
OFF
OFF
OFF
OFF

Select the item with the SERVICE button and press the TEST
button to alternate the display to and from ON and OFF.
Outputting corresponds to the ON/OFF alternation.
When exiting from OUTPUT TEST with ON display, all of
ON displays change to OFF.
Bring the arrow to EXIT and press the TEST BUTTON to
return to the menu mode.

-> EXIT
SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

C. SOUND TEST
This test mode allows each sound used in the game to be checked.

SOUND TEST

No. 0

Press the SERVICE button to increase the number
sequentially, emitting the next sound to be tested.
Press the TEST button to return to the TEST MENU.

SELECT WITH SERVICE BUTTON
PRESS TEST BUTTON TO EXIT

D. C.R.T. TEST
Selecting C.R.T. test causes the monitor to display the following and allows
the 3 screens (displayed simultaneously) to adjust brightness balance.

C.R.T. TEST

PRESS TEST BUTTON TO EXIT

E. GAME ASSIGNMENTS
Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings
to be displayed and allows game setting changes (game difficulty, etc.) to be made. After setting
changes, be sure to exit from the TEST mode; the settings are not renewed until the TEST mode is
exited.
SETTING CHANGE PROCEDURE
1
2
3

Press the SERVICE BUTTON to move the “->” to the desired item.
Change to the desired setting by using the TEST BUTTON.
To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.
GAME DIFFICULTY (TRAINING)
Sets the game difficulty for the TRAINING Mode.
Game difficulty can be set from among the 5 categories, i.e.,
VERY EASY, MEDIUM EASY, NORMAL, MEDIUM
HARD, and VERY HARD. Specifically, this varies the
qualifying points in the TRAINING Mode.

GAME ASSIGNMENTS

GAME DIFFICULTY (TRAINING)
NORMAL
GAME DIFFICULTY (FLIGHT)
NORMAL

GAME DIFFICULTY (FLIGHT)
Sets the difficulty for the FLIGHT Mode.
Game difficulty can be set from among the 5 categories, i.e.,
VERY EASY, MEDIUM EASY, NORMAL, MEDIUM
HARD, and VERY HARD. Specifically, this varies the initial
time for each course in the FLIGHT Mode.

-> EXIT

SELECT WITH SERVICE BUTTON
PRESS TEST BUTTON TO EXIT

F. VOLUME SETTING
When VOLUME SETTING is selected, the following appears on the screen and each Control Unit’s Volume
can be set.
If the operability is unsatisfactory, or when adjusting or replacing the Volume, set the Volume in this mode.

METHOD OF VOLUME SETTING

VOLUME SETTING
CONTROL WHEEL (AILERON)
CONTROL WHEEL (ELEVATOR)
RUDDER PEDAL
THRUST LEVER L
THRUST LEVER R

MIN
50H
(20H)
50H
(20H)
50H
(20H)
50H
(20H)
50H
(20H)

MAX
80H
(DFH)
80H
(DFH)
80H
(DFH)
80H
(DFH)
80H
(DFH)

NEU
BFH
(BOH)
BFH
(BOH)
BFH
(BOH)

•To perform Volume setting, move all Volumes
from the minimum value to the maximum value
and select “EXIT WITH SAVE” and the status of
the CONTROL WHEEL and RUDDER PEDAL
are returned to the horizontal (neutral) position.

EXIT WITH
SAVE
--> EXIT WITHOUT SAVE

•If “EXIT WITHOUT SAVE” is selected, the
setting is cancelled. The values in parentheses

SELECT WITH SERVICE BUTTON
PRESS TEST BUTTON TO EXIT

have already been saved.

G. BOOKKEEPING
Choosing BOOKKEEPING in the MENU mode displays the data of the present operating status on 2 pages.
Press the TEST BUTTON to proceed to PAGE 2/2. Pressing the TEST BUTTON while the second page is
displayed returns the screen to the MENU mode.
BOOKKEEPING

PAGE1/2

TOTAL TIME
PLAY TIME
AVERAGE PLAY TIME
LONGEST PLAY TIME
SHORTEST PLAY TIME

OD
OD
OD
OD
OD

OH
OH
OH
OH
OH

OM
OM
OM
OM
OM

OS
OS
OS
OS
OS

TOTAL TIME:
Refers to TOTAL TIME energized except for the time
used for the TEST Mode.

PLAY TIME:
Refers to the game play time.

PRESS TEST BUTTON TO CONTINUE

BOOKKEEPING PAGE 2/2
TIME HISTOGRAM
0M00S
0M30S
1M00S
1M30S
2M00S
2M30S
3M00S
3M30S
4M00S
4M30S
5M00S
5M30S
6M00S
6M30S
7M00S
7M30S
8M00S
8M30S
9M00S
9M30S
OVER

~ 0M29S
~ 0M59S
~ 1M29S
~ 1M59S
~ 2M29S
~ 2M59S
~ 3M29S
~ 3M59S
~ 4M29S
~ 4M59S
~ 5M29S
~ 5M59S
~ 6M29S
~ 6M59S
~ 7M29S
~ 7M59S
~ 8M29S
~ 8M59S
~ 9M29S
~ 9M59S
10M00S

0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

In Page 2/2, Histogram of Number of Play as against Play
Time is displayed. For setting the DIFFICULTY, refer to
this histogram.

By-playtime play frequency bookkeeping is displayed in
increments of 30 seconds from 0M00S to 9M59S.
Playtime in excess of 10 minutes is displayed all in the
category of OVER 10M00S.

PRESS TEST BUTTON TO EXIT

H. BACKUP DATA CLEAR
This allows the contents of BOOKKEEPING and Player Ranking data to be cleared.
BACKUP DATA CLEAR

YES (CLEAR)
-> NO (CANCEL)

When clearing, use the SERVICE BUTTON to
bring the arrow to “YES (CLEAR)” and press the
TEST BUTTON.
When the data has been cleared, “COMPLETED”
will be displayed, and it will automatically return to
the BACKUP DATA CLEAR menu. Bring the
arrow to “NO” and press the TEST BUTTON to
return the screen to MENU mode.

SELECT WITH SERVICE BUTTON
PRESS TEST BUTTON TO EXIT

Note that despite the “clear” execution, the
settingsof the GAME ASSIGNMENTS, COIN
ASSIGNMENTS, and BOARD SETTINGS do not
change. Be very careful, however, because the
remaining credits will be deleted

8. CONTROL MECHA
Be sure to turn power off before performing work, and avoid touching undesignated
places. Failure to do so can result in electric shock and short circuit accidents.
Be careful so as not to damage wirings. Damaged wiring can cause electric shock
and short circuit hazards.
When performing work, be sure to use 2 or more persons. One person alone performing work can cause accidents and parts damage.
In the test mode, if the CONTROL HANDLE’s VR variations are not within the allowable range, then a VR
installation position adjustment or VR replacement is needed. Also, be sure to apply grease to the VR gear
portion once every 3 months.

8 - 1 REMOVING THE CONTROL MECHANISM
1

Turn the power switch off.

Remove the 3 Hexagon Socket Bolts from the lower part of the Control Panel.

Remove the 4 Tamperproof Screws from both sides of the control panel’s front

Remove the 3 Tamperproof Screws from the underside of the control panel.

Carefully draw out the Control Mechanism in a mnner so as not to damage wiring and connectors inside the
control panel..

8 - 2 ADJUSTING THE VOLUME
Never touch places other than those specified. Touching unspecified places can
cause electric shock and/or short circuit.
After the replacement or adjustment of the VR, be sure to set the variable value of
the VR in the test mode’s Volume Setting.
1

The Volume Brackets can be
moved by loosening 2 screws from
each Bracket.

Move the Volume Brackets to
disengage the Adjust Gear mesh,
and move the Volume Shaft so that
the cut portion of the Volume Shaft
faces opposite the Center Reference Hole of the Adjust Gear.

Engage Gears and fasten the 2 screws.

Carefully move the CONTROL WHEEL left/right & forward/backward, and check to ensure that the
Volume range is not exceeded

Upon completion of adjustment, be sure to perform Volume Setting in the TEST mode.

8-3 REPLACING THE VOLUME
1

Disconnect the wiring connector.

Take out the 2 screws which secure the volume Bracket and remove the Volume Bracket.

3 Take out the 2 screws to remove the Volume Gear and replace the Volume.
4

After replacing the Volume, follow the steps in 8-2 to adjust theVolume.

8 - 4 GREASING
Be sure to turn the power off first, before performing work, and avoid touching
unspecified places. Failure to do so can cause electric shock and/or short circuit.

Be sure to use the designated grease. Using undesignated grease can cause parts
damage
Do not apply greasing to undesignated places. Doing so can cause malfunctioning
or quality deterioration of parts.
Apply greasing to the following portions every 3 months.
For Spray Grease, use NOK GLUBER L60 or GREASE MATE (Part No. 090-0066).
For greasing the backside of the Centering Mechanism, take out the 4 Hexagon Socket Bolts and remove
the Centering Base.

8 - 5 REPLACING THE SWITCH LEVER
Before starting to work, ensure that the Power SW is OFF. Failure to observe this
can cause electric shock/short circuit.
Use care so as not to damage wirings. Damaged wiring can cause electric shock
and short circuit hazards.

1 Take out the 4 screws and
remove the Switch Plate. Be
careful so as not to damage
wiring.

2 Remove and replace the Switch Lever.

9. LEVER UNIT
In order to prevent electric shock and short circuit, be sure to turn off the power
before performing work on the interior parts of the product.
Be careful not to damage wiring. Damaged wiring can cause electric shock or short
circuit.
Do not touch places other than those specified. Touching unspecified places can
cause an electric shock or short circuit.
If the value movements of the Lever are Irregular, adjust or replace the Volume in the following procedure.

9 - 1 ADJUSTING THE VOLUME
1 Remove the 4 screws to loosen the
Lever Cover. Take out the 2 screws
and remove the Shift Cover Lower.

2 The Volume Brackets can be moved
by loosening the 2 screws securing
each.
3 By moving the Volume Bracket,
disengage ADJUST GEAR mesh.
Move the Volume Shaft in the
manner so that the cut portion of the
Volume Shaft faces opposite the
center of the ADJUST GEAR.
4 Mesh gears and fasten the 2 screws.
5 Carefully move the Lever forward
& backward, and check to ensure
that the Volume range is not
exceeded.
6 After making adjustments, be sure
to perform Volume setting in the
TEST mode.

9 - 2 REPLACING THE VOLUME
Be sure to turn the power off first, before performing work, and avoid touching
unspecified places. Failure to do so can cause electric shock and/or short circuit.

1 Remove the Volume Gear from the Volume to replace the Volume.
2 After replacing the Volume, make adjustments as per 11-1 ADJUSTING THE VOLUME.

9 - 3 GREASING
Be sure to turn the power off first, before performing work, and avoid touching
unspecified places. Failure to do so can cause electric shock and/or short circuit.

Be sure to use the designated grease. Using undesignated grease can cause parts
damage
Do not apply greasing to undesignated places. Doing so can cause malfunctioning
or quality deterioration of parts.
Apply greasing to the following portions once every three (3) months.
For Spray Grease, use NOK GLUBER L60 or GREASE MATE (Part No. 090-0066).

10. PEDAL UNIT
In order to prevent electric shock and short circuit, be sure to turn off the power
before performing work on the interior parts of the product.
Be careful not to damage wiring. Damaged wiring can cause electric shock or short
circuit.
Do not touch places other than those specified. Touching unspecified places can
cause an electric shock or short circuit.
In the TEST mode, if the value movements of the CONTROL WHEEL are irregular, adjust or replace the
Volume in accordance with the following procedure:

10 - 1 ADJUSTING THE VOLUME
1 Take out the 4 screws and remove the
Pedal Mechanism Cover.

2 Loosen the 2 screws securing each Volume
Bracket and move the Volume Brackets.
3 Move the Volume Bracket to disengage
gear mesh. Move the Volume Shaft in the
manner so that the cut portion of the
Volume Shaft faces opposite the center of
the ADJUST GEAR.
4 Engage the gears and fasten the 2 screws.
5 Carefully move the Pedal forward &
backward and check to ensure that the
Volume range is not exceeded.
6 Upon completion of adjustment, be sure to
perform Volume setting in the TEST mode.

10 - 2 REPLACING THE VOLUME
Be sure to turn the power off first, before performing work, and avoid touching
unspecified places. Failure to do so can cause electric shock and/or short circuit.

1 Remove the Volume Gear from the Volume to replace the Volume.
2 After replacing the Volume, make adjustments as per 12-1 ADJUSTING THE VOLUME.

10 - 3 GREASING
Be sure to turn the power off first, before performing work, and avoid touching
unspecified places. Failure to do so can cause electric shock and/or short circuit.

Be sure to use the designated grease. Using undesignated grease can cause parts
damage
Do not apply greasing to undesignated places. Doing so can cause malfunctioning
or quality deterioration of parts.
Apply greasing to the following portions once every three (3) months.
For Spray Grease, use NOK GLUBER L60 or GREASE MATE (Part No. 090-0066).

11 . COIN SELECTOR
HANDLING THE COIN JAM
If the coin is not rejected when the REJECT BUTTON is pressed, open the coin chute door
and open the selector gate. After removing the jammed coin, put a normal coin in and check
to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

1
2
3

GATE

The coin selector should be cleaned
once every 3 months. When cleaning,
follow the procedure below:
Turn the power for the machine OFF.
Open the coin chute door.
Open the gate and dust off by using a
soft brush (made of wool, etc.).
Remove and cleen smears by using a
soft cloth dipped in water or diluted
chemical detergent and then squeezed
dry.
Remove the CRADLE.
When removing the retaining ring(Ering), be very careful so as not to bend
the shaft.
Remove stain from the shaft and pillow
portions by wiping off with a soft cloth,
etc.
After wiping as per #5 above, further
apply a dry cloth, etc. to cause the coin
selector to dry completely.

FIG. 11a

CRADLE
FIG.11b

Never apply machine oil, etc. to
the coin selector
After cleaning the Coin Selecting,
Insert a regular coin in the normal
working status and ensure that
the Selector correctly functions.

COIN INSERTION TEST
Once a month, when performing the COIN SW
TEST, simultaneously check the following:
Does the Coin Meter count satisfactorily?
Does the coin drop into the Cashbox correctly?
Is the coin rejected when inserted while keeping
the REJECT BUTTON is pressed down?

Insert a coin
while keeping
the Reject
Button pressed
down and check
if it is
rejected.
COIN METER

FIG. 11c

OPTIONAL DOLLAR BILL ACCEPTOR

THE COIN DOOR ASSEMBLY USED ON AIRLINE PILOTS STD TYPE
COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL
NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE
THE GAME FOR THIS APPLICATION.
THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING
VALIDATORS:
HOLE POSITION#1
(FORWARD-MOST POSITION)

Mars 2000 series

HOLE POSITION#2

Mars 2000 series
DBV45 (JCM)

HOLE POSITION #3

CURRENTLY NOT USED

HOLE POSITION #4

DSI01*

*The back flange on the chute can be removed for hold position #4.
If the flange is not removed, it may interfere with the back of the
cabinent.

The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series
upstacker. A 2000 series stacker can be added by simply removing the top two entry door and replacing it with a one
entry door with a cut-out for a stacker. This one entry door can be ordered through Coin Controls or one of Coin Controls
authorized distributors. The part number is 91-4000-01. The Mars stacker can be obtained through an autherized Mars
distibutor.

12. MONITOR
12 - 1 CAUTIONS AND WARNINGS CONCERNING THE SAFETY FOR HANDLING THE MONITORS
When performing such work as installing and removing the monitor, inserting and disconnecting the external connectors to and from monitor, be sure to disconnect the power connector
(plug) before starting work. Proceeding the work without following this instruction can cause
electric shock of malfunctioning.
Using the monitor by converting it without obtaining a prior permission is not allowed. SEGA
shall not be liable for any malfunctioning and accident caused by said conversion.

Primary side and secondary side
The monitor’s circuit which is divided into the Primary
side and secondary side, is electrically isolated. Do
not touch the primary side and the secondary side
simultaneously. Failing to observe the instruction can
cause electric shock, and this is very dangerous.
When making monitor adjustments, use a nonconductive driver and make adjustment without
touching any other part other than the Adjustment
V.R. and Knob. Also, be sure not to cause a shortcircuit to the Primary side and the Secondary side. If
short-circuited, it can cause electric shock or malfunctioning, which is very dangerous.
High tension Voltage
Some of the parts inside the monitor are subject to high-tension voltage in excess of 20,000
volts and very dangerous. Therefore, do not touch the monitor interior. Should soldering &
paper wastes, etc. be mixed in the monitor, turn the power off so as not to cause malfunctioning or fire hazard.

Connecting the CRT and PCB
For combining the CRT and PCB, use the specified part No. to maintain the status of adjustments made at the factory. The anode of the CRT itself will be accumulitavely charged as time
elapses, generating high tension voltage which is very dangerous. The monitor should be used
with the Chassis, CRT and PCB assembled. When repair, etc. is required at the time of malfunctioning, be sure to send it in an “as assembled” condition. If these are disassembled, what’s
charged to said high tension voltage can be discharged, causing a very hazardous situation.
Therefore, under no circumstances should it be disassembled.

Static Electricity
Touching the CRT surface sometimes causes you to slightly feel electricity. This is because the
CRT surfaces are subject to static and will not adversly affect the human body.
Installation and removal
Ensure that the Magnetizer Coil, FBT (Fly-Back Transformer), Anode Lead and Focus Lead are
not positioned close to the sheet metal work’s sharp edges, etc. and avoid damaging the
insulated portions so as not to cause an electric shock and malfunctioning. (For the name of
parts, refer to the above figures.)

For the purpose of static prevention,
special coating is applied to the CRT
face of this product. To protect the
coating, pay attention to the following
points. Damaging the coating film can
cause electric shock to the customers.
For the caution to be heeded when
clearing, refer to the Section of Periodic
inspection Table.
Do not apply or rub with a hard item (a
rod with pointed edge, pen, etc.) to or
on C.R.T. surfaces.
Avoid applying stickers, seals, etc. on
the C.R.T. face.
Do not remove aluminum foils from the
C.R.T. corners. Removing the aluminum
foils can cause static prevention effects
to be lowered.

Monitor adjustments have been made at the time of shipment. Therefore do not make further adjustment without a justifiable reason.
Adjusting the monitor which contains high tension parts is dangerous
work. Also, an erroneous adjustment can cause deviated synchronization and image fault, resulting in malfunctioning.
When making adjustment, utilize a resinous Alignment Rod. Servicing
with bare hands or using conductive tools can cause electric shock.
12 - 2 CAUTIONS TO BE HEEDED WHEN CLEANING THE CRT SURFACES
Static preventive coating is applied to the CRT surfaces. Peeling off
this coating can cause electric shock. When cleaning, pay attention to
the following points:
Remove smears by using a dry, soft cloth (flannels, etc.). Do not
use a coarse gauze, etc.
For smear removing solvent, alcohol (ethanol) is recommended.
When using chemical detergent, e sure to folow instructions
below:
Dilute chemical detergent with water and dip a soft cloth in and
then thoroughly wring it to wipe smears off.
Do not use a chemical detergent containing an abrasive, powder
or bleaching agent.
Do not use alkaline chemical detergents such as “glass cleaner”
available on the market or solvents such as thinner, etc.
Do not rub or scratch the CRT face with hard items such as scrub
brushes, etc.
Clean the CRT surfaces once a week. When cleaning, pay attention to the above cautions so that the antistatic
coating will not come off.

12 - 3 ADJUSTMENT METHOD
Monitor adjustments are made at the time of shipment. Therefore,
do not make further adjustments without a justifiable reason.
Adjusting a monitor which contains high tension parts is dangerous
work. Also, an erroneous adjustment can cause deviated synchronization and image fault, resulting in malfunction.
When making adjustments, utilize a resinous Alignment Rod. Servicing with bare hands or using tools made of conductive material
can cause electric shock.

13. REPLACING THE FLUORESCENT LAMP
When performing the work, be sure to turn power off. Working
with power on can cause an electric shock or short circuit accident.
The Fluorescent Lamp, when it gets hot, can cause burns. Be
very careful when replacing the Fluorescent Lamp.
To perform work safely and securely, be sure to use a step which is in a
secure and stable condition. Not using a step or using an unstable step can
cause violent falling accidents.

13 -1 METHOD OF REPLACEMENT
1

Take out the 2 Truss Screws and remove the Plate Holder.

Lower the Billboard Plate and replace the Fluorescent Lamp.

14. PERIODIC INSPECTION TABLE
The items listed below require periodic checks and maintenance in order to retain the performance of this
machine and ensure safe operation.
Be sure to check once a year to see if Power Cords are damaged, the Plug is
securley inserted, dust is accumulated between the Socket Outlet and the Power
Plug, etc. Using the product when dust has accumulated can cause a fire or
electrical shock.
Once a year, request an interior cleaning from the place of contact stated herin or
from the Distributer from which the product was purchased. Using the product
when dust has accumulated in the interior can result in a fire or short circuit
accident. Note that cleaning the interior parts can be performed on an individual
pay-basis.

ITEMS
CABINET
CONTROL MECHANISM
LEVER UNIT

PEDAL UNIT
COIN CHUTE TOWER

MONITOR
SEAT
GAME BD
INTERIOR
POWER PLUG
CABINET SURFACES

DESCRIPTION
Check Adjusters’ contact with surface.
Check VOLUME Value.
Check SW.
Check VOLUME Value.
GREASING
Check VOLUME Value.
Check COIN SWes.
Coin insertion test.
COIN SELECTOR cleaning.
Cleaning CRT face.
Check Adjustments.
Antistatic measures.
MEMORY TEST.
Setting check.
Cleaning.
Inspection and cleaning.
Cleaning.

PERIOD
Daily
Monthly
Monthly
Monthly
Trimonthly
Monthly
Monthly
Monthly
Trimonthly
Weekly
Monthly or when moving
Bimonthly
Monthly
Annually
As occasion arises

CLEANING CABINET SURFACES
If the cabinet is badly stained, use a cloth which is dipped in the chemical detergent liquid diluted with water and then
squezzed dry. Do not use thinner, benzine, alcohol or chemical dustcloths, as these can damage the Cabinet surfaces.

SEAT (Greasing to Seat Rail Portion)
Move the Seat to the rearmost position and apply spray grease to the portion
shown at the right once every 3 months, using NOK KLUBER L60 or
GREASE MATE (Part No. 090-0066). After greasing, move the seat
forward and backward a few times to allow the grease to be applied
uniformly. Be sure to wipe off any grease that contacts the surfaces of the
PROTECTIVE RUBBER on the Seat Rail, and any excess grease.

15. TROUBLESHOOTING
Should trouble occur, first check wiring connections.
PROBLEMS
When Main SW is
ON, there is no
activation.

CAUSE
The power is not on.

COUNTERMEASURES
Firmly insert the plug into the outlet.

Power supply/voltage is incorrect.

Make sure that the power supply/voltage
is correct.
Check the fuse. Remove the cause of
overload and replace the fuse.

AC main fuse causes the power to be
cut off due to momentary overload.
Irregular sound
emitted from
inside Rear Cabinet

Greasing to gear mesh portion is not
satisfactory, or extraneous matter
mixed in.

Apply greasing or eliminate extraneous
matter.

No sound is emitted.

Sound Volume adjustment is not
correct.

Adjust the SWITCH UNIT’s speaker
volume.

Sound BD and Amp are
malfunctioning.

Perform SOUND TEST to find and
replace defective parts.

No sound from
Cockpit.

In correct Cabinet Type Setting.

Correct Cabinet Type Setting.

The Fluorescent
lamp does not
light up.

The Fluorescent tube is burnt out.

Replace the Fluorescent tube.

The image coloring
on the MONITOR
is incorrect.

Affected by C.R.T. magnetization.

Press the DEMAG. SW on the SWITCH
UNIT.
Make appropriate adjustments.

Incorrect monitor adjustment.

Operation of
Deviation of Volume.
CONTROL WHEEL,
RUDDER PEDAL,
Volume malfunctioning.
and THRUST LEVER
is not satisfactory.
ADJUST GEAR mesh is incorrect.

Adjust Volume value in the TEST mode.
Replace the Volume.
Adjust ADJUST GEAR mesh.

CIRCUIT PROTECTOR
Functions due to the activation of bimetal. To restore the function, wait approximately one minute
or longer until the bimetal cools off, and press the button.

16. GAME BOARD
In order to prevent an electrical shock, be sure to turn power off
before performing work.
Be careful so as not to damage wirings. Damaged wiring can cause an
electric shock or short circuit accident.

In this product, setting changes are made during the test mode. The Game
BD need not be operated. Use the Game BD, etc. with the same settings
made at the time of shipment. Do not expose the Game BD, etc.
without good reason .

16 -1 LOCATING THE GAME BOARD
1 Turn power off.
2 Take out a total of 6 Truss Screws and
unlock to remove the Seat.

3 The GAME BOARD is located at the
position shown in the photo below.

16 - 2 COMPOSITION OF GAME BOARD
Be sure to use the specified settings for the DIP SWes on the Filter Board. Failure
to do so may cause irregularities or malfunctioning, such as unsatisfactory images
displayed on the screen.

ASSY CASE NAO USA (840-0005D-05)

DIP SW SETTING
In this product, be sure to set all of the DIP SWes to OFF.

17. DESIGN RELATED PARTS

DESIGN RELATED PARTS

ITEM NO.
1
2
3
6
7
8
9
10
11
12
13
14
15
16
17
18
19

PART NO.

DESCRIPTION

APC-0202
422-0748-01
APC-3110-A
APC-1551-A
APC-1571-A
421-9749-02
APC-1501-A
APC-1501-B
APC-1511-A
422-0751-91-01
APC-2502-D
APC-2502-C
APC-2502-B
SPG-1201-E
APC-1078
APC-3005
APC-1583

BILLBOARD PLATE STD
SUB INSTR SH APC STD ENG
STICKER SEAT BACK
STICKER SIDE L
STICKER SIDE R
STICKER SEGA LOGO BLOW WHITE
STICKER BASE L APC
STICKER BASE R APC
STICKER BASE LID
PLAY INSTR SH APC STD ENG
DESIGN PL METER C
DESIGN PL METER B
DESIGN PL METER A
METER PANEL
STICKER CENTER MARK
STICKER THRUST
SW PLATE STD

18. PARTS LIST
1 TOP ASSY APC STD

1 TOP ASSY APC STD
ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
24
29

APC-10001
APC-0200
APC-0300
RAL-0006
SDW-0005
SDW-0006
SDW-0007
SDW-0008
SDW-0009
INY-0004
DYN-0008
DYN-0011
421-7308-~
422-0748-01
SGM-3863
APC-0004
APC-0012X

ASSY COCKPIT
ASSY BILLBOARD STD
ASSY COINCHUTE TOWER
BLIND CAP
AC COVER
AC LID
CONNECTOR COVER
WIRE COVER
TOWER COVER
BACK LID INY
BACK LID B
DENOMI PLATE W/O ORIGINAL
DENOMI SH 1GAME ~
SUB INSTR SH APC STD ENG
POLTHN COVER 950 X 1800 X 1700
BILLBOARD HOOK
BILLBOARD HOLDER STD

201
202
203
204
205
206
207
208
209

030-000820-SB
068-852216-OB
000-P00408-WB
000-T00512-OB
010-P00408-F
008-T00412-OB
050-F00800
000-T00416-OC
060-F00800-OB

HEX BLT W/S BLK M8 X 20
FLT WSHR BLK 8.5-22 X 1.6
M SCR PH W/FS BLK M4 X 8
M SCR TH BLK M5 X 12
S-TITE SCR PH W/F M4 X 8
TMP PRF SCR TH BLK M4 X 12
FLG NUT M8 S=12
M SCR TH CRM M4 X 16
FLT WSHR BLK M8

2 ASSY BILLBOARD STD (APC-0200)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5

APC-0201
APC-0202
APC-0203
APC-0204
APC-0205

BILLBOARD BASE
BILLBOARD PLATE STD
PLATE HOLDER
CONNECTOR LID
BOLT LID

000-T00408-OC

M SCR TH CRM M4 X 8

201

3 ASSY COINCHUTE TOWER (APC-0300)

ITEM NO.

PART NO.

DESCRIPTION

1
2
4
5
6
7
9
12

APC-0301
DRT-0301
SDW-0360
DP-1167
105-5172
253-5366
421-7501-02
APC-0303

COINCHUTE TOWER
COIN METER BRKT
SW UNIT
TNG LKG
CHUTE PLATE DOUBLE
CASH BOX
STICKER 6.3V 0.15A
CONN PNL TOWER STD

101
102
103
104

220-5482-91-~
220-5237-92-~
2205643-01
220-5574
220-5575

ASSY C.C 2DR ~
ASSY C.C 2DR ~
MAG CNTR DC5V 6P WH MZ-674-D04
CAM LOCK W/KEYS
CAM LOCK MASTER W/O KEY

201

000-P00408-W

M SCR PG W/FS M4 X 8

4 SW UNIT (SDW-0360)

ITEM NO.

PART NO.

DESCRIPTION

KR-1060

SW BRACKET

101
102
103

509-5028
220-5179
601-0042

SW PB 1M
VOL CONT B-5K OHM
KNOB 22MM

5 ASSY COCKPIT (APC-10001)

5 ASSY COCKPIT (APC-10001)
ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
19
20
21

APC-1500
APC-1550
APC-1570
APC-1600
APC-2200
APC-20001
SPG-1008
APC-1088
APC-1089
SDW-1023
SDW-1024
APC-1019
APC-1080
TTR-1067X
DYN-1025
SPG-1005
INY-1016
RAL-2007
RAL-2008
INY-1015

ASSY MAIN BASE
ASSY MONITOR COVER L
ASSY MONITOR COVER R
ASSY SEAT STD
PEDAL UNIT
ASSY CTRL PNL
ROOF LID
SIDE PNL L
SIDE PNL R
FOOT COVER L
FOOT COVER R
MONITOR STAND
WIRE COVER BOX
MONITOR MASK
RUBBER CUSHION
MASK HOLDER
MONITOR SUPPORT
RUBBER HOLDER R TWIN
RUBBER HOLDER L TWIN
CRT ADJUST PANEL

101
105
106
107
108

200-5787
280-5112
280-5113
280-5114
280-5185-6

ASSY CLR DSPL 29TYPE 31K 100V
BUSH FOR TV
COLLAR FOR TV
SPACER 6.4-25 X 2
SPACER TUBE L=6

201
202
203
204
205
206
207
208
210
211
212
213
214
215
216
217
218
219

030-000850-SB
068-852216-OB
030-000820-SB
060-F00800-OB
000-F00508
050-F00600
000-P00408-WB
030-000840-SB
008-B00830-OB
068-552016-OB
000-T00512-OB
000-T00530-OB
000-P00312-WB
DYN-1019
060-S00800-OB
000-T00408-OB
008-B00820-OB
050-F00800

HEX BLT W/S BLK M8 X 50
FLT WSHR BLK 8.5-22 X 1.6
HEX BLT W/S BLK M8 X 20
FLT WSHR BLK M8
M SCR FH M5 X 8
FLG NUT M6
M SCR PH W/FS BLK M4 X 8
HEX BLT W/S BLK M8 X 40
TMP PRF SCR BH BLK M8 X 30
FLT WSHR BLK 5.5-20 X 1.6
M SCR TH BLK M5 X 12
M SCR TH BLK M5 X 30
M SCR PH W/FS BLK M3 X 12
FLT WASHER M8
SPR WSHR BLK M8
M SCR TH BLK M4 X 8
TMP PRF SCR BH BLK M8 X 20
FLG NUT M8 S=12

6 ASSY MAIN BASE (APC-1500)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5

APC-1520
APC-1530
APC-4500
APC-4600
APC-1502

ASSY BASE BOX
AC UNIT
ASSY MAIN BD STD
ASSY PWR SPLY STD
FOOT BASE

101

260-0011-02

AXIAL FLOW FAN AC100V 50-60HZ

201
202
203
204
205
206
207
208

000-P00425-W
068-441616
030-000616-SB
060-F00600-OB
000-P00408-WB
000-P00350
060-F00300
060-S00300

M SCR PH W/FS M4 X 25
FLT WSHR 4.4-16 X 1.6
HEX BLT W/S BLK M6 X 16
FLT WSHR BLK M6
M SCR PH W/FS BLK M4 X 8
M SCR PH M3 X 50
FLT WSHR M3
SPR WSHR M3

7 ASSY BASE BOX (APC-1520)

ITEM NO.

PART NO.

DESCRIPTION

APC-1501
DYN-2004
APC-1523
APC-1510
APC-1522
APC-1521
DYN-2007X
DYN-2009X

MAIN BASE
LOCK TNG
BASE LID BRKT
ASSY BASE LID R
FLOOR MAT
BASE LID F
LID EDGE L
LID EDGE R

101

220-5575

CAM LOCK MASTER W/O KEY

201
202
203
204
205

000-T00512-OB
031-000514-OB
050-F00500
031-000414-OC
050-F00400

M SCR TH BLK M5 X 12
CRG BLT BLK M5 X 14
FLG NUT M5
CRG BLT CRM M4 X 14
FLG NUT M4

1
2
3
4
5
6
7
8

8 MAIN BASE (APC-1501)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5
6

DYN-2002X-A
APC-1501-A
APC-1501-B
SDW-1103
601-5699X
601-5471

MAIN BASE BLANK
STICKER BASE L APC
STICKER BASE R APC
BASE FOOT
LEG ADJUSTER BOLT M16 X 75
CASTER

201
202

030-000816-S
050-H01600-OB

HEX BLT W/S M8 X 16
HEX NUT BLK M16

9 ASSY BASE LID R (APC-1510)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5

DYN-2011
DYN-2012
DYN-2013
DYN-2014
APC-1511

LOCK ROD A
LOCK ROD B
LOCK ARM
ROD HOLDER
BASE LID R

101

601-7551

LOCK HANDLE

201
202
203

045-C02520
031-000510-OB
050-F00500

COT PIN 2.5 X 20
CRG BLT BLK M5 X 10
FLG NUT M5

10 AC UNIT (APC-1530)

ITEM NO.

PART NO.

DESCRIPTION

APC-1531

AC BRKT

214-0202
509-5453-91-V-B

AC INLET PANEL TYPE
SW ROCKER J8 V-B

101
105

11 ASSY MAIN BD STD (APC-4500)

ITEM NO.

PART NO.

DESCRIPTION

APC-4501
840-0005D-05
837-13551-92

WOODEN MAIN BASE STD
ASSY CASE NAO APC W/O JAL
I/O CONTROL BD FOR JVS

101

400-5397

SW REGU FOR JVS

201
202
204

000-P00416-W
011-P00325
011-T03512

M SCR PH W/FS M4 X 16
TAP SCR PH 3 X 25
TAP SCR TH 3.5 X 12

1
2
3

12 ASSY PWR SPLY STD (APC-4600)

ITEM NO.

PART NO.

DESCRIPTION

APC-4601

WOODEN PWR SPLY BASE STD

101
102
103

560-5426-H
838-11856CE-02
601-10369

XFMR 100-120V 100V 5.5A
CONNECT BD W/FUSE 6.3A CE
STEREO PWR AMP 47

201
202
204

000-P00416-W
011-P00325
011-T03512

M SCR PH W/FS M4 X 16
TAP SCR PH 3 X 25
TAP SCR TH 3.5 X 12

13 ASSY MONITOR COVER L (APC-1550)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3

APC-1550
APC-1560
DYN-1032

COVER PANEL L
ASSY SPEAKER L
MASK BRKT

000-P00408-W

M SCR PH W/FS M4 X 8

201

14 ASSY SPEAKER L (APC-1560)

ITEM NO.

PART NO.

DESCRIPTION

APC-1561

SPEAKER BRKT

101

130-5156

SPEAKER BOX 8OHM 20W

201

000-P00512-W

M SCR PH W/FS M5 X 12

15 ASSY MONITOR COVER R (APC-1570)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3

APC-1571
APC-1565
DYN-1032

COVER PANEL R
ASSY SPEAKER R
MASK BRKT

000-P00408-W

M SCR PH W/FS M4 X 8

202

16 ASSY SPEAKER R (APC-1565)

ITEM NO.

PART NO.

DESCRIPTION

APC-1561

SPEAKER BRKT

101

130-5156

SPEAKER BOX 8OHM 20W

201

M SCR PH W/FS M5 X 12

17 ASSY SEAT STD (APC-1600)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
11
12

APC-3101
APC-3112
APC-3103
STC-1612
APC-3105
APC-3113
APC-3107
APC-3110
DYN-2131
DYN-2132
APC-3114
GHO-3705

SEAT BASE
SEAT FRAME STD
SEAT MOUNT TRAY
PROTECT RUBBER
SAFETY GUARD FRONT
SAFETY GUARD REAR STD
SAFETY GUARD SIDE
SEAT REAR COVER STD
UPPER SEAT
LOWER SEAT
SEAT BASE REAR
FLT WSHR 8.5-26 X 3.2

101
102

601-9059
601-9060

SEAT RAIL L
SEAT RAIL R

201
202
203
204
205
206
207
208

000-T00408-OB
000-T00412-OC
030-000816-S
030-000850-S
050-H00800
060-S00800
068-441616-OC
068-852216

M SCR TH BLK M4 X 8
M SCR TH CRM M4 X 12
HEX BLT W/S M8 X 16
HEX BLT W/S M8 X 50
HEX NUT M8
SPR WSHR M8
FLT WSHR CRM 4.4-16 X 1.6
FLT WSHR 8.5-22 X 1.6

18 PEDAL UNIT (APC-2200)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

APC-2201
APC-2202
APC-2203
APC-2204
APC-2205
APC-2206
APC-2207
APC-2208
APC-2209X
APC-2210X
APC-2211
APC-2212
APC-2213
AIN-2108
SAS-1178
TTR-2010
601-6450
601-6555

PEDAL BASE
STOPPER SHAFT
STOPPER RUBBER
MAIN PIPE
ARM
PEDAL UPPER
PEDAL LOWER
PEDAL COVER
PEDAL REAR L
PEDAL REAR R
ROSTA BRKT
VOL BRKT
PEDAL MECHA COVER
RING
FLT WSHR BLK 8.5-30 X 2
GEAR HOLDER 110
GEAR 110
GEAR =30 M=0.75

101
102
103
105
106

100-5120
220-5484
601-8917
100-5168
100-5070

BEARING (FYH BLP 204)
VOL CONT B-5K OHM
ROSTA 22 (DR-S 27 X 40)
BEARING 20 (NSK 6904ZZ)
BEARING 15 (NSK 6002ZZ)

201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219

000-P00410-W
000-P00408-WB
000-T00408-OB
028-A00410-P
030-000620-S
030-000816-S
030-000830-S
050-F00400
050-H00800
050-H01400
060-S00800
060-S01400
060-F00800
068-441616
068-652016
068-852216
050-F00600
000-P00406-S
060-F00400

M SCR PH W/FS M4 X 10
M SCR PH W/FS BLK M4 X 8
M SCR TH BLK M4 X 8
SET SCR HEX SKT CUP P M4 X 10
HEX BLT W/S M6 X 20
HEX BLT W/S M8 X 16
HEX BLT W/S M8 X 30
FLG NUT M4
HEX NUT M8
HEX NUT M14
SPR WSHR M8
SPR WSHR M14
FLT WSHR M8
FLT WSHR 4.4-16 X 1.6
FLT WSHR 6.5-20 X 1.6
FLT WSHR 8.5-22 X 1.6
FLG NUT M6
M SCR PH W/S M4 X 6
FLT WSHR M4

19 ASSY CTRL PNL (APC-20001)

19 ASSY CTRL PNL (APC-20001)
ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

APC-2501
APC-2502-01
APC-2000
APC-2100
APC-2150
APC-3250
APC-1066
APC-1078
APC-2503
APC-2504
APC-3202
APC-3203
APC-3204
APC-3206
APC-1580
APC-1582
APC-1583
APC-2505
APC-1073
SPG-2039
APC-2506
APC-3205
601-6555
APC-2014
APC-3208
APC-2508
APC-2507
APC-3005

CTRL PNL BASE STD
CTRL PNL COVER STD EXP
ASSY CONTROL MECHA
ASSY YOKE
ASSY VIRTUAL BUTTON
ASSY LEVER MECHA
YOKE COVER
STICKER CENTER MARK
SHIFT COVER LOWER
COVER ADJUST BRKT
LEVER COVER
LEVER KNOB
KNOB BUSH
JOINT BRKT
ASSY SW PLATE STD
LEVER SW COVER
SW PLATE STD
MECHA ADJUSTER STD
OUTER COLLAR
SPACER RING
LEVER SIDE BRKT
VR BRKT LEVER
GEAR Z=30 M=0.75
INSULATOR BUSH
INSULATOR PAPER LEVER
SPACER PIPE STD
STICKER BLACK
STICKER THRUST

104

220-5484

VOL CONT B-5K OHM

201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218

000-T00416-OB
060-S00800-OB
020-000820-OZ
000-T00412-OC
020-000512-HZ
060-S00500
068-441616-OC
030-000816-SB
008-T00416-OB
000-P00408-W
020-000612-OZ
060-S00600
060-F00600
028-A00404-P
000-P00412-W
050-F00400
008-T00416-OB
000-T00406-OC

M SCR TH BLK M4 X 16
SPR WSHR BLK M8
HEX SKT H CAP SCR BLK OZ M8 X 20
M SCR TH CRM M4 X 12
HEX SKT CAP SCR BLK OZ M5 X 12
SPR WSHR M5
FLT WSHR CRM 4.4-16 X 1.6
HEX BLT W/S BLK M8 X 16
TMP PRF SCR TH BLK M4 X 16
M SCR PH W/FS M4 X 8
HEX SKT H CAP SCR BLK OZ M6 X 12
SPR WSHR M6
FLT WSHR M6
SET SCR HEX SKT CUP P M4 X 4
M SCR PH W/FS M4 X 12
FLG NUT M4
TMP PRF SCR TH BLK M4 X 16
M SCR TH CRM M4 X 6

20 ASSY CONTROL MECHA (APC-2000)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

APC-2050
APC-2030
APC-2090
APC-2003
APC-2004
APC-2012
APC-2006
APC-2007
601-7088-91
601-10572
601-8966
APC-2001
APC-2008
APC-2009
APC-2013
APC-2010
APC-2011
APC-2014

ASSY SLIDE BASE
ASSY CENTERING MECHA
ASSY SHAFT GUIDE
STOPPER RUBBER STROKE
STOPPER SHAFT STROKE
VR BRKT STROKE INSU
CABLE BEAR BRKT
STROKE DAMPER SHAFT
GEAR 64
GEAR 80
GEAR HOLDER
MECHA BASE
SPRING HOOK
EXT SPRING LONG
VR BRKT ROLL INSU
INSULATOR PAPER ROLL
INSULATOR PAPER STROKE
INSULATOR BUSH

102
103

601-10574
220-5484

STROKE DAMPER
VOL CONT B-5K OHM

202
203
204
205
206
207
208
209
211
212
213
214

060-S00800-OB
060-F00800-OB
020-000820-OZ
050-U00800
000-P00408-W
060-S00600
060-F00600
028-A00308-P
000-P00410-WB
020-000410-HZ
060-F00400
060-S00400

SPR WSHR BLK M8
FLT WSHR BLK M8
HEX SKT H CAP SCR BLK OZ M8 X 20
U NUT M8
M SCR PH W/FS M4 X 8
SPR WSHR M6
FLT WSHR M6
SET SCR HEX SKT CUT P M3 X 8
M SCR PH BLK W/FS M4 X 10
HEX SKT CAP SCR BLK OZ M4 X 10
FLT WSHR M4
SPR WSHR M4

21 ASSY CENTERING MECHA (APC-2030)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5
6
7

APC-2031
APC-2032
APC-2033
APC-2034
APC-2035
APC-2036
APC-2037

CENTERING BASE
CENTERING GUIDE
EXT SPRING
SPRING SHAFT
SPRING COLLAR INNER
SPRING COLLAR OUTER
MUTE RUBBER

000-P00408-W
000-P00310-W
250-5421
060-F00400

M SCR PH W/FS M4 X 8
M SCR PH W/FS M3 X 10
FLT WSHR 3.5-12 T=1.0
FLT WSHR M4

201
202
203
204

22 ASSY SLIDE BASE (APC-2050)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5
6
8
9
10
11
12
13
14
15

APC-2051
APC-2052
APC-2053
APC-2054
APC-2055
APC-2056
APC-2058
APC-2059
601-10575
601-7088-91
APC-2060
APC-2061
APC-2062
APC-2063

MAIN SHAFT
INNER BASE
HOUSING PLATE 30
HOUSING PLATE 20
STOPPER RUBBER ROLL
STOPPER SHAFT ROLL
SLIDE BRKT L
SLIDE BRKT R
RACK
GEAR 64
GUARD BRKT
STOPPER
INNER COLLAR
GUIDE PLATE

102
103
104
105
106

100-5340
100-5168
100-5341
601-10573
601-6231-B045

BEARING 30 (6806ZZ)
BEARING 20 (NSK 6904ZZ)
SLIDE RAIL
ROTARY DAMPER ROLL
EDGING NEW TYPE

201
202
203
204
205
206
207
208
210
211
212
213
214
215
216

000-P00308-W
020-000512-HZ
060-S00500-OB
050-U00800
060-F00800-OB
000-P00408-W
000-P00312-W
060-F00400
028-A00308-P
000-T00408-OC
050-U00400
060-S00400
060-F00500-OB
029-000020
000-P00408-S

M SCR PH W/FS M3 X 8
HEX SKT CAP SCR BLK OZ M5 X 12
SPR WSHR BLK M5
U NUT M8
FLT WSHR BLK M8
M SCR PH W/FS M4 X 8
M SCR PH W/FS M3 X 12
FLT WSHR M4
SET SCR HEX SKT CUP P M3 X 8
M SCR TH CRM M4 X 8
U NUT M4
SPR WSHR M4
FLT WSHR BLK M5
HEX SKT H CAP SCR M4 X 10
M SCR PH W/S M4 X 8

23 ASSY SHAFT GUIDE (APC-2090)

ITEM NO.

PART NO.

DESCRIPTION

1
3

APC-2091
APC-2093

GUIDE BUSH BRKT
L BRKT

000P00408-W

M SCR PH W/FS M4 X 8

201

24 ASSY YOKE (APC-2100)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5
6

APC-2101
APC-2102
APC-2103
RCR-2151
RCR-2152
GLC-2036

YOKE
THUMB CAP
TRIGGER CAP
HANDLE GRIP RIGHT
HANDLE GRIP LEFT
STOPPER

000-P00410-OB
008-P00510-OB
000-P00208
060-F00200

M SCR PH BLK M4 X 10
TMP PRF SCR PH BLK M5 X 10
M SCR PH M2 X 8
FLT WSHR M2

201
202
203
204

25 ASSY VIRTUAL BUTTON (APC-2150)

ITEM NO.
1
2
101
102
103

PART NO.

DESCRIPTION

APC-2151X
171-6478B

VR BUTTON BRKT
PC BD LIGHTING SWX5

212-5205-12
509-5560-Y*
509-5561-S**

CONN JST M 12P RTA
PB SW W/L 6V 1L Y
PB SW W/L 6V 5L S

* HAPP Part No. 55-0006-25 available
** HAPP Part No. 55-0006-42 available

26 ASSY LEVER MECHA (APC-3250)

ITEM NO.

PART NO.

DESCRIPTION

1
2
3
4
5
6
7
8
9
10

APC-3251
APC-3252
APC-3253
APC-3254
APC-3255
APC-3256
APC-3257
APC-3258
TTR-2009
601-6005

LEVER GUIDE
LEVER BRKT INNER
LEVER BRKT OUTER
LEVER SHAFT
SHUTTER PLATE
STOPPER RUBBER LEVER
STOPPER SHAFT LEVER
Z BRKT
GEAR HOLDER 80
ADJUST GEAR

101

601-10571

ROTARY DAMPER LEVER

201
202
203
204
205
206

000-P00330-W
000-P00408-W
028-A00408-P
050-U00800
060-F00800
000-P00408-S

M SCR PH W/FS M3 X 30
M SCR PH W/FS M4 X 8
SET SCR HGEX SKT CUP P M4 X 8
U NUT M8
FLT WSHR M8
M SCR PH W/S M4 X 8

27 ASSY SW PLATE STD (APC-1580)

ITEM NO.

PART NO.

DESCRIPTION

APC-1581

SW BSE STD

101
102
103
104
105
108

390-6640-GR
390-6640-RE
509-5910
509-5911-G
509-5911-R
280-5185-7

LED BD-0811-12V GREEN
LED BD-0811-12V RED
ROCKER SW M-2012YG
SW LEVER AT-4157 GRAY
SW LEVER AT-4157 RED
SPACER TUBE L=7

201

050-F00300

FLG NUT M3

VISIT OUR WEBSITE!

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Creator                         : Adobe® PageMaker® 6.5
Create Date                     : 2000:10:11 15:46:01
Subject                         : 
Title                           : 
Author                          : darld
Producer                        : Acrobat PDFWriter 4.05  for Power Macintosh
Modify Date                     : 2000:10:12 12:39:34-07:00
Page Count                      : 97

EXIF Metadata provided by EXIF.tools

Arcade Airline Pilot Manual User

APC-manual APC-manual

Navigation menu

Versions of this User Manual:

Views

Navigation