Arcade Deal Or No Mega Deluxe Manaul User Manual
2013-11-13
User Manual: Arcade Deal Or No Mega Deluxe Manaul
Open the PDF directly: View PDF 
.
Page Count: 21
| Download | |
| Open PDF In Browser | View PDF |
DN1600 MEGA SPIN Installation Guide INNOVATIVE CONCEPTS IN ENTERTAINMENT INC. 10123 MAIN STREET, CLARENCE, NY 14031 SERVICE: 1-716-759-0360 FAX: 1-716-759-0884 EMAIL: service@icegame.com WEBSITE: www.icegame.com 1 Your kit includes the following: (2) (1) (1) (1) (4) (1) (1) (10) (2) Advertising Signs - DN7660 Restore Disk - DN2690x Mega Spin Wheel Deluxe Dongle - DN2614 1/4-20 X 1 1/2 BHCS (BLACK) - 6281 5/32 Allen wrench - PC60601A 3/32 Allen wrench - 6603 Cable ties - 348 1/4-20 x 1 1/2 (Zinc) - 6102 Should any of these items be missing, please contact ICE service department at (716) 759-0360 Monday through Friday, 8:30a.m. to 6:00p.m. Eastern standard time before beginning the installation. It is recommended to review each step before you begin your install of this kit. The use of a ladder and one additional person is highly recommended to lift the assembly onto the game’s cabinet. If you have any question please contact ICE Service Department for support. Step 1 Remove power to the game by unplugging the AC power cord from the machine. Remove the monitor’s back access mesh panel using the supplied 3/32 Allen wrench. Remove the lower, back panel of the cabinet. You will need to also unplug the fans on cabinet door as you remove it. Unplug the power cable and ground wire going to the marquee. Remove the existing marquee that is above the monitor using a 5/32 Allen wrench and discard these bolts. Step 2 Unpack the new Mega Bonus Wheel and remove the base as shown in figure 1A on page 4 using a 5/32 Allen wrench supplied with this kit. Save the hardware for step 6. Step 3 Install the base on top of the cabinet where the marquee was originally mounted using four 1/4-20 X 1 1/2 Allen bolts included in the kit. See figure1B for the location of which counter bored holes on the base to use. Step 4 Remove the 6 bolts located at the top of the new wheel and install the old marquee there. Plug in the power and ground wires as shown in figure1C. Bolt the marquee to the top of the Mega Bonus Wheel housing shown in figure 1D using the 6 bolts that were previously removed. Only two bolts are shown for clarity. Step 5 Lift the Mega Bonus Wheel onto the top of the game cabinet and position the holes on the base for installation. It is recommended that the use of a ladder and two people perform this step. Route the wires for power and ground, through the left hole standing from behind the game. Refer to figure 1E for location. Plug in the AC power from the marquee and ground wire as shown in figure 3. The LED power harness and USB cable should be feed through the right hole as shown in figure1F. Be careful not to pull to hard on the USB cable when pulling through the top of the cabinet. 2 Step 6 Reinstall the bolts you saved from step 2 to secure the Mega Bonus wheel housing (figure 1.G). Step 7 From the back of the cabinet, slide out the computer and feed the USB and wheel harness through the hole on the right side. This harness goes behind the computer and to the bottom of the cabinet. Step 8 Plug in the USB cable and the DOND DLX dongle into the back of the computer’s USB connectors. See figure 4. Do not remove the old dongle already plugged into the computer. This requires two dongles to work.. Step 9 The wheel harness is plugged in at the bottom of the cabinet. The connectors located on the shorter side of the harness go to the bottom right connectors (red to red, blue to blue). The connectors with the longer part of the harness go to the connectors on the bottom left (figure5).** Secure the wheel harness to the existing harness in the cabinet using cable ties included in the kit. Step 10 Hardware installation is complete (figure6). Step 11 Plug the power cable into the back of the game and start the machine. Record your game settings before installing the new software as it will completely over write all information including game settings. Insert the software update CD and restart the machine to begin the installation. Leave the tray that the computer is on out of the cabinet so the CD drive can eject. Once the software update is complete, remove the disk and restart the computer. When the software first boots, it will ask which wheel is installed. Select the wheel that matches your wheel that you have installed. Step 12 Once the game is running, press the DIAG button of the programming panel to enter the Service Menu. Using Vol+/Vol- to move and start to select, select the System Tests Menu → Wheel Spin Test → Slot #9 1000. The wheel should spin and land on 1000. Exit out of the Service Menu. Step 13 Connect the fans on the cabinet door. Reinstall the cabinet door and the mesh screen. Note: ** Newer games will have a free connector in the main harness. In older games, the main harness will be disconnected from the LED strips at the bottom of the cabinet and the wheel harness will be connected to these connectors (main harness is connected to the wheel harness which is connected to the LED strips). 3 Figure 1 4 Figure 2 Figure 3 Figure 4 5 Figure 5 Figure 6 6 Advertising Signage Installation: Unscrew the bolts at the top corners, above the screen and discard the bolts. Using the Zinc 1/4-20 bolts attach the signs as shown below. Procedure for removing the wheel Step 1: Remove front cover by removing the 2 Allen bolts that hold the lower black plastic trim Step 2: Remove the nuts that secure the cover to the vacuum form shell Step 3: Remove the plastic cover Step 4: Remove the “E” clip using a small flat screw driver in the center of the hub that holds the hub to the motor shaft (Figure 7,8) Step 5: Using the 3 finger holes grip the plastic wheel and pull straight back (Figure 9) 7 Figure 7 Figure 8 Figure 9 8 9 10 11 12 13 14 Note: Home Flag is pointing at the highest value of the wheel when re-installing. 15 16 DEAL OR NO DEAL PROGRAMMING OPTION GUIDE MEGA BONUS STANDARD GAME SOFTWARE VERSION DOND V.01.14.00.US.STD INNOVATIVE CONCEPTS IN ENTERTAINMENT INC. 10123 MAIN STREET, CLARENCE, NY 14031 SERVICE: 1-716-759-0360 FAX: 1-716-759-0884 E-MAIL: service@icegame.com WEBSITE: www.icegame.com MAIN MENU OPERATOR ADJUSTMENTS - adjust various game play/operation settings AUDITS - view game/coin/ticket audit data TICKET USE DEFAULT = ON - this setting allows the operator to turn off the ticket output of the game EVEN VALUES ONLY DEFAULT = OFF -forces tickets to be even values Main Menu - Operator Adjustments COIN SETTINGS RESET MENU - reset game/coin/ticket audits SYSTEM INFORMATION MENU - displays system information FREEPLAY DEFAULT = OFF - this setting allows the game to be played without a credits in. SYSTEM TESTS MENU - perform various system tests/diagnostics CURRENCY TYPE DEFAULT = DOLLAR - this is the currency type used by the game. VIEW LOG - displays record of debug information CURRENCY UNIT VALUE DEFAULT = $0.25 -this is the value of a single unit for a particular currency. For example, 0.25 is the credit unit value that corresponds to a US quarter. Main Menu - OPERATOR ADJUSTMENTS GAME ADJUSTMENTS - adjust game play settings COIN 1 VALUE DEFAULT = $0.25 - this is the value of coin input #1. TICKET ADJUSTMENTS - turn the ticket mechanism on/off COIN 2 VALUE DEFAULT = $0.25 - this is the value of coin input #2. COIN ADJUSTMENTS - adjust the currency type and coin switch values COIN 3 VALUE / DBV PULSE DEFAULT = $1.00 - this is the value of coin input #3, which is commonly used as the dollar bill validator input. PLAYER COST / PAYOUT ADJUSTMENTS - adjust the cost of the game and the level of pay out VOLUME - adjust the volume for the game Main Menu - Operator Adjustments GAME ADJUSTMENTS COUNT DOWN TIMER DEFAULT = 10 -this is the length of time that the player has to make an input during the game. The value can be set from 5 to 20 seconds PRIZE TYPE - type of prize to be awarded. COUPONS, POINTS, BLANK DEFAULT = TICKET SELECT WHEEL TYPE -tells the software which wheel values you installed. DEMONSTRATION MODE -Puts the game into free mode and allows the players to experience the wheel spin frequently. Main Menu - Operator Adjustments TICKET MECH ADJUSTMENT TICKET MULTIPLER -ticket multiplier DEFAULT = 10 MAXIMUM CREDITS DEFAULT = $500.00 - this is the maximum number of credits that are allowed by the machine. BONUS AWARD -bonus award value DEFAULT = $0.00 UNITS FOR BONUS AWARD -bonus award unit DEFAULT = $0.00 Main Menu - Operator Adjustments PLAYER COST / PAYOUT START COST DEFAULT = $1.00 - cost to start the game [min = FREE, max = $25.00] START COST (DOUBLE DEAL) DEFAULT = $2.00 - cost to start the Double Deal game. (note: the Double Deal mode is the same as the regular game, except that all the payout values are doubled the cost of the Double Deal game should almost always be twice the cost of the regular game.) [min = FREE, max = $25.00] BONUS VALUE -value each bonus is worth DEFAULT = $0.00 TICKET VALUE -value each ticket is worth DEFAULT = $0.01 Main Menu - Operator Adjustments - VOLUME GAME VOLUME DEFAULT = 24 - on a scale of 0 - 32, this is the volume of the game. ATTRACT VOLUME DEFAULT = 24 - on a scale of 0 - 32, this is the volume of the game while it is in the attract mode. MINIMUM VOLUME DEFAULT = 4 - this is the absolute minimum that both the GAME VOLUME and the ATTRACT VOLUME can be set to ATTRACT SOUNDS DEFAULT = ALWAYS - this setting determines how often sounds are played during the attract mode. The possible values are OFF / OCCASIONALLY and ALWAYS. Main Menu - AUDITS CURRENT PAYOUT - this is the current payout percentage calculated over the lifetime of the game. Main Menu - General Audits - SYSTEM AUDITS PLAY TIME - this is the total amount of time that the game has been played. UP TIME - this is the length of time that the game has been plugged in and running. WATCHDOGS - this is a count of the number of time that the game has been forced to reset, most likely to a hardware or software error. GAME AUDITS - audits for total number of plays, game time, etc. EXCEPTIONS - this is a count of the number of times that the software has caused a system error. TICKET AUDITS - audits for the number of tickets won, average tickets, number of tickets owed, etc. BAD TRAPS - this is a count of the number of times that the software has caused a game error. SYSTEM AUDITS - audits for play time, up time, etc. COIN AUDITS - audits for the number of coins in, etc. Main Menu - Audits - GAME AUDITS TOTAL GAMES PLAYED - the total number of games played on the machine. GAMES PLAYED (DEAL) - the total number of regular games played. GAMES PLAYED (DOUBLE DEAL) - the total number of "Double Deal" games played. # OF TIMES WHEEL SPUN - the total number of times bonus wheel has been spun # OF TIMES PLAYER HAS WON BIG BONUS - the total number of times the player has won the big bonus value Main Menu - Audits - TICKET AUDITS LIFETIME TICKETS PAID - this is the total number of tickets paid since software install CURRENT TICKETS OWED - this is the number of tickets currently owed Main Menu - Audits - COIN AUDITS TOTAL COIN 1 - the total amount of money in from coin door #1. TOTAL COIN 2 - the total amount of money in from coin door #2. TOTAL COIN 3 (DBV) - the total amount of money in from coin door #3, commonly used as a dollar bill validator. BONUS COINS - the total amount of bonus coins awarded for the lifetime of the game LIFETIME COIN COUNT - the total amount of money in from all coin doors for the lifetime of the game. SERVICE CREDITS - the total amount of money in from the service credits button. Main Menu - RESET MENU RESET GAME AUDITS - this option clears out the game audits. RESET CREDITS - this option clears out the number of credits currently in the game. RESET TICKETS - this option clears the amount of TICKETS owed by the game. Main Menu - VIEW LOG -displays debug information for software development RESET COIN COINTERS - this option clears out the counters for each of the coin doors. RESET ADJUSTMENTS - this option sets all of the game adjustments back to the factory default values. FACTORY RESET - this option will reset all of the audits and adjustments back to the factory defaults. Main Menu - SYSTEM INFORMATION VERSION LIST - this will display the versions for the various components of the game software. DIPSWITCH SETTINGS - this option displays the settings for each of the dipswitches on the IO board. SWITCH TELEMETRY DATA - this displays debug information of missed switch presses Main Menu - SYSTEM TESTS TICKET DISPENSER TEST - this option prints out a ticket. SWITCH TEST - this option allows the operator to test the internal switches such as coin and volume controls. SCREEN TESTS - this option allows the operator to perform various display tests, such as color and screen alignment SOUND TEST - this allows the operator to test the audio system by playing a variety of test sounds. FILE TEST - this option initiates a file test, in which every system file is checked for integrity. COIN METER TEST - this option will send a test output to the coin meter. The coin meter should increase by one. CABINET LAMPS TEST - this option begins a test of the lamps in the cabinet WATCHDOG TEST - this option tests the ability for the game to restart itself in the case of a hardware or software failure 4 3 2 1 BROWN x 2 G/Y x 2 BLUE x 2 1 2 3 GRN/YLW 1 TO: AC AND GROUND IN MARQUEE HEADER MS2364X E00253 SH2130X D BLACK G/Y WHITE BROWN GRN/YLW BROWN E00253 1 2 3 D 1 BROWN x 2 2 G/Y x 2 3 BLUE x 2 1 BROWN x 2 2 G/Y x 2 3 BLUE x 2 1 2 3 E00253 E00253 LED STRIP #E00439DNX 1 2 orange black/green 1 red 2 black LED STRIP #E00414DNX 1 2 1 red 2 black LED STRIP #E00439DNX orange black/yellow C 1 2 3 SH2130X 1 2 1 BROWN x 2 2 G/Y x 2 3 BLUE x 2 1 red 2 black E00417 CR130933 orange black/green x 2 red tan/black black 1 2 1 2 3 1 red 2 black LED STRIP #E00414DNX E00439ADNX HOME OPTO black white blue orange red yellow orange black/yellow x 2 LED STRIP #E00439DNX 1 2 orange black/orange 1 red 2 black LED STRIP #E00414DNX 1 2 orange black/red 1 red 2 black LED STRIP #E00439DNX 1 2 orange black/orange x 2 1 red 2 black 1 2 orange black/red x 2 1 2 3 1 2 3 4 5 6 BLACK G/Y WHITE BLACK G/Y WHITE 1 2 3 4 5 6 SH2130X white/black white black/blue black/orange black/red black/yellow BLACK G/Y WHITE 1 2 3 1 BROWN x 2 2 G/Y x 2 3 BLUE x 2 1 2 3 1 BROWN x 2 2 G/Y x 2 3 BLUE x 2 1 BROWN x 2 2 G/Y x 2 3 BLUE x 2 DN2680LX C WHEEL MOTOR SH2130X 1 red 2 black LED STRIP #E00414DNX DN2661MX DN2681HX DN2680LX DN2660LX GND +5V 1 2 3 4 12/24V POWER SUPPLY tan/black black red BROWN G/Y x 2 BLUE BA2063LX orange black/white 1 2 3 +12V LED J2 SENSE ORANGE LIGHT BLUE BLACK E00629 USB A/B TO: USB PORT ON PC A 1 orange 2 black/red orange black/red x 2 1 2 orange black/orange x 2 1 orange 2 black/yellow orange black/yellow x 2 1 2 1 2 DN2681LX 1 2 orange black/green TO: LEDS ON RIGHT SIDE OF MAIN CABINET orange black/green x 2 1 2 3 GRN/YLW 1 TO: AC AND GROUND IN MONITOR CABINET TITLE DN BONUS WHEEL FILENAME SYSTEM SCHEMATIC DESCRIPTION 1 2 DATE 3 BROWN x 2 G/Y x 2 BLUE x 2 page 1 PART NO. TO: LEDS ON RIGHT SIDE OF MAIN CABINET 1 orange 2 black/orange 4 B DN2661MX J3 +12V DS2010 J5 +24V +24V OUT 1 OUT 2 OUT 3 OUT 4 GND EARTH GND +24V B 1 2 3 4 5 6 ORANGE 1 2 3 4 5 white/black white black/blue black/orange black/red black/yellow BLACK GRN/YLW LIGHT BLUE DN2036X J6 8/9/11 2 REVISED 8/11/11 REQUIRED SIGNATURES DN7600KX ENGINEER SYSTEM SCHEMATIC.VSD DRAWN BY NBRANCATO PAGE 1 OF 1 1 MANAGER VENDOR A
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Tagged PDF : No XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:30 Modify Date : 2011:12:05 15:41:36Z Create Date : 2011:12:05 15:41:36Z Metadata Date : 2011:12:05 15:41:36Z Creator Tool : Adobe Acrobat 8.3 Combine Files Format : application/pdf Creator : David M. Bartel Document ID : uuid:353aab87-c694-af4a-8fc3-f47c1231db3f Instance ID : uuid:939b43e8-2e4e-b84d-8f32-c425f5815857 Producer : Adobe Acrobat 8.3 Page Count : 21 Author : David M. BartelEXIF Metadata provided by EXIF.tools