Arcade Mario & Sonic At The Rio 2016 Olympic Games™ Edition (4 Player With Marquee) User Manual

Mario & Sonic At The Rio 2016 Olympic Games™ Arcade Edition (4 Player - With Marquee) 0 Mario & Sonic at the Rio 2016 Olympic Games™ ARCADE EDITION (4 Player - With Marquee)_0 Mario & Sonic at the Rio 2016 Olympic Games™ ARCADE EDITION (4 Player - With Marquee)_0 sharedfiles soe-web-arcade2-pub

Mario & Sonic At The Rio 2016 Olympic Games™ Arcade Edition (4 Player - With Marquee) Manual Mario & Sonic at the Rio 2016 Olympic Games™ ARCADE EDITION (4 Player - With Marquee) Manual Mario & Sonic at the Rio 2016 Olympic Games™ ARCADE EDITION (4 Player - With Marquee) Manual sharedfiles soe-web-arcade2-pub

User Manual: Arcade Mario & Sonic At The Rio 2016 Olympic Games™ Arcade Edition (4 Player - With Marquee)

Open the PDF directly: View PDF .
Page Count: 88

IMPORTANT

• Before using this product, read this manual carefully to understand the

contents herein stated.

• After reading this manual, be sure to keep it near the product or in a

convenient place for easy reference when necessary.

OWNER'S & SERVICE MANUAL 420-0025-02UK

MARIO & SONIC 4P OVERHEAD GANTRY

Sega Amusements International Limited.

42 Barwell Business Park, Leatherhead Road, Chessington, Surrey, KT9 2NY. United Kingdom.

Telephone: +44 (0) 208 391 8090 Facsimile: +44 (0) 208 391 8099

email: mailbox@sega.co.uk Web: http://www.segaarcade.com

Sega Corporation

Canal Side Bldg 1-39-9 Higashi-shinagawa Shinagawa-ku, Tokyo, 140-8583, Japan.

Telephone: +81-3-687-7133 Facsimile: +81-3-687-7134

© SEGA

Errors and omissions excepted (E&OE)

1st PRINTING

March 2016

OWNER’S & SERVICE MANUAL

4 PLAYER OVERHEAD GANTRY &

MARQUEE

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:

To maintain safety:

To ensure the safe operation of this product, be sure to read the following before usage.

The following instructions are intended for the users, operators and the personnel in charge of the operation of the

product. After carefully reading and sufciently understanding the warning displays and cautions, handle the product

appropriately. Be sure to keep this manual close to the product or in a convenient place for future reference.

Herein, explanations which require special attention are enclosed with dual lines. Depending on

the potentially hazardous degrees, the terms of DANGER, WARNING, CAUTION, etc. are used. Be sure to

understand the contents of the displays before reading the text.

Indicates that mishandling the product by disregarding this pictograph will

cause severe injury or death.

Indicates that mishandling the product by disregarding this warning will cause a

potentially hazardous situation which can result in death or serious injury.

Indicates that mishandling the product by disregarding this caution will cause a

slight hazardous situation which can

result in personal injury and/or material damage.

For the safe usage of the product, the following pictographs are used:

Indicates "HANDLE WITH CARE." In order to protect the human body and equipment, this display is at-

tached to places where the Owner's Manual, Serviceman Manual and/or Service Manual should be referred

to.

• Perform work in accordance with the instructions herein stated. Instructions for work are explained

by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions

can cause accidents. In the case where only those who have technical expertise should perform the work

to avoid hazardous situation, the instructions herein state that the site maintenance personnel should

perform such work.

• Be sure to turn off the power before working on the machine. To prevent an electric shock, be sure

to turn off the power before carrying out any work that requires direct contact with the interior of the

product. If the work is to be performed in the power-on status, the Instruction Manual herein always states

to that effect.

• Be sure to ground the Earth Terminal. (This is not required in the case where a power cord with earth is

used.)

• This product is equipped with the Earth Terminal. When installing the product, connect the Earth

Terminal to the "accurately grounded indoor earth terminal" by using an earth wire. Unless the product is

grounded appropriately, the user can be subject to an electric shock. After performing repair, etc. for the

control equipment, ensure that the Earth Wire is rmly connected to the control equipment.

• Ensure that the Power Supply used is equipped with an Earth Leakage Breaker. This product does

not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth

Leakage Breaker can cause a re when earth leakage occurs.

• Besuretousefuseswhichmeetthespeciedrating. (Only for the machines which use fuses.)

Using fuses exceeding the specied rating can cause a re and an electric shock. (Only for the machines

which use fuses.)Using fuses exceeding the specied rating can cause a re and an electric shock.

• Specification changes (removal of equipment, conversion and addition) not designated by SEGA are

not allowed. The parts of the product include warning labels for safety, covers for personal protection, etc. It

is very hazardous to operate the product by removing parts and/or modifying the circuits. Should doors, lids

and protective parts be damaged or lost, refrain from operating the product, and contact where the product was

purchased from or the ofce herein stated. SEGA shall not be held responsible for any accidents, compensation

for damage to a third party, resulting from the specications not designated by SEGA.

• Ensure that the product meets the requirements of appropriate electrical specications. Before installing the

product, check for electrical specications. SEGA products have a nameplate on which electrical specications

are described. Ensure that the product is compatible with the power supply voltage and frequency requirements

of the location. Using any electrical specications different from the designated specications can cause a re

and an electric shock.

• Install and operate the product in places where appropriate lighting is available, allowing warning labels to be

clearly read. To ensure safety for the customers, labels and printed instructions describing potentially hazardous

situations are applied to places where accidents can be caused. Ensure that where the product is operated has

sufcient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please

place an order with where the product was purchased from or the ofce herein stated.

• When handling the monitor, be very careful. (Applies only to products with monitors.) Some of the monitor

parts are subject to high tension voltage. Even after turning off the power, some portions are still subject to

high tension voltage sometimes. Monitor repair and replacement should be performed only by those technical

personnel who have knowledge of electricity and technical expertise.

• Be sure to adjust the monitor properly. (Applies only to products with monitors.) Do not operate the product

leaving on-screen ickering or blurring as it is. Using the product with the monitor not properly adjusted may

cause dizziness or a headache to an operator, a player, or the customers.

• When transporting or reselling this product, be sure to attach this manual to the product.

• In the case where commercially available monitors and printers are used in this product, only the contents

relatingtothisproductareexplainedherein.Somecommerciallyavailableequipmenthasfunctionsand

reactions not stated in this manual. Read this manual together with the specic instruction manual of such

equipment.

• Descriptionshereincontainedmaybesubjecttoimprovementchangeswithoutnotice.

• Thecontentsdescribedhereinarefullypreparedwithduecare.However,shouldanyquestionariseorerrorsbe

found,pleasecontactSEGA.

INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION

Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting

to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on the power,

check the following points to ensure that the product has been transported in a satisfactory status.

• Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet?

• Are casters and adjusters damaged?

• Do the power supply voltage and frequency requirements meet with those of the location?

• Are all wiring connectors correctly and securely connected? Unless connected in the correct way, connector

connections can not be made accurately. Do not insert connectors forcibly.

• Do power cables have cuts and dents?

• Are all accessories available?

• Can all doors and lids be opened with the accessory keys? Can doors and lids be rmly closed?

iv

INTRODUCTION

INTRODUCTION

This companion manual is intended to provide detailed descriptions together with all necessary information covering

the general operation of electronic assemblies, electromechanical, servicing control, spare parts, etc. for the product,

"MARIO & SONIC AT THE RIO 2016 OLYMPIC GAMES ARCADE EDITION" 4 PLAYER.

This manual is intended for the owners, personnel managers in charge of operation of this product.

Operate the product after carefully reading and sufciently understanding the instructions.

In the unlikely event that the product does not function correctly, DO NOT allow anyone other than a technician to

touch the internal system. Turn off the power to the machine, making sure to unplug the electrical cord from the out-

let, and contact the ofce listed below or the point-of-purchase for this product.

Use of this product is unlikely to cause physical injuries or damage to property. However, points that require special

attention are indicated by bold text, the words "STOP, IMPORTANT or CAUTION” and the symbols below.

Indicates important information that, if ignored, may result in the mishandling

of the product and cause faulty operation or damage to the product.

Indicates a warning or caution that, if ignored, may result in the mishandling

of the product and cause faulty operation or damage to the product.

Sega Amusements International Limited.

42 Barwell Business Park, Leatherhead Road, Chessington, Surrey, KT9 2NY. United Kingdom.

International Sales: +44 (0) 208 391 8090 Facsimile: +44 (0) 208 391 8099

email: mailbox@sega.co.uk Web: http://www.segaarcade.com

Sega Corporation

Canal Side Bldg 1-39-9 Higashishinagawa Shinagawa-ku, Tokyo, 140-8583, Japan.

Telephone: +81-3-687-7133 Facsimile: +81-3-687-7134

Sega Total Solutions

42 Barwell Business Park, Leatherhead Road, Chessington, Surrey, KT9 2NY. United Kingdom.

Parts & Service: +44 (0) 208 391 8060 Facsimile: +44 (0) 208 391 8096

Play It! Amusements, inc.

252 Beinoris Drive, Wood Dale, IL. 60191, USA

Parts & Service: +00 (1) 224 265 4287

INTRODUCTION

v

Parts replacement, maintenance inspections and troubleshooting should be carried out by site maintenance personnel

or other qualied professionals. This manual includes directions for potentially dangerous procedures which should

only be carried out by professionals with the appropriate specialised knowledge.

The site maintenance personnel or other qualied professionals mentioned in this manual are dened as follows:

Site maintenance personnel:

Individuals with experience in maintaining amusement equipment, vending machines, etc., working under the super-

vision of the owner/operator of this product to maintain machines within amusement facilities or similar premises by

carrying out everyday procedures such as assembly, maintenance inspections, and replacement of units/expendable

parts.

Activities to be carried out by site maintenance personnel:

Amusement equipment/vending machine assembly, maintenance inspection and replacement of units/expendable

parts.

Other qualied professionals:

Persons employed by amusement equipment manufacturers, or involved in design, production, testing or mainte-

nance of amusement equipment. The individual should have either graduated from technical school or hold similar

qualications in electrical/electronics/mechanical engineering.

Activities to be carried out by other qualied professionals:

Amusement equipment/vending machine assembly, repair/adjustment of electrical/electronic/mechanical parts.

Denition of 'Site Maintenance Personnel or Other Qualied Individuals

Servicing and maintenance work of the contents herein stated should be

performed by the SERVICEMAN stipulated as per IEC Standard. Those who do not

have technical expertise and knowledge other than the SERVICEMAN are not

allowed to perform the work herein stated. Executing aforementioned work by

such non-technical personnel can cause serious accidents that may endanger life.

vi

INTRODUCTION

Electrical & Mechanical Specications

Individual Dimensions.

Cabinet: 1.23m (48.4in) [width] x 0.89m (35.1in) [depth]

1.93m (76.0in) [height]

Billboard: 1.21m (47.6in) [width] x 0.49m (19.3in) [depth]

0.44m (17.3in) [height]

Floor Plate: 0.86m (33.9in) [width] x 0.80m (31.5in) [depth]

0.90m (45.4in) [height]

Assembled Dimensions: 1.23m (48.4in) [width] x 1.47m (57.9in) [depth]

2.27m (89.3in) [height]

Weights: Cabinet 262kg (577.6lb.) Floor 54kg (119lb.)

Marquee L 106kg (233.7lb) Marquee R 104kg (229.2lb)

Monitor w/mount [35+10kg] 45kg (99.2lb)

Installed 4 Player

Machine Dimensions: 6.68m (263in.) [W] x 1.62m (63.8in.) [D] x 3.19m (125.6in.) [H]

Machine Weight: 1660Kg

Rating

Single Machine: AC240V 1.4A [336W] / AC120V 2.6A [624W]

Marquee: AC240V 3.2A [768W] / AC120V 6.2A [744W]

SPECIFICATIONS

INTRODUCTION

vii

Waste of Electrical and Electronic Equipment (WEEE) Statement.

Waste of Electrical and Electronic Equipment (WEEE) Statement.

The WEEE (Waste of Electrical and Electronic Equipment) directive places an obligation on all EU based

manufacturers and importers of Electrical and Electronic Equipment (EEE) to ensure waste equipment is disposed of

in accordance with the directive at the end of their useful life.

The symbol shown below will be placed on all products manufactured from 13th August 2005, which indicates this

product must NOT be disposed of with other normal waste. Upon purchasing any EEE from SEGA Amusements

International Ltd. The user accepts responsibility to dispose of their waste equipment by arranging to return it to a

designated UK collection point (AATF) or an Approved Exporter (AE) for the correct recycling of waste electrical

and electronic equipment.

For more information on Approved Authorised Treatment Facilities (AATF) within the UK please consult the

government website www.gov.uk

For users outside of the UK EEE should be disposed of in accordance with the local policy on the recycling of Waste

Electrical and Electronic Equipment.

Battery Recycling Statement.

The EC Directive on Batteries and Accumulators (2006/66/EC) aims to minimise the impact of batteries on the

environment and encourage the recovery of the materials they contain. To achieve increased collection and recycling

of waste batteries, the Directive places ‘producer responsibility’ obligations on manufacturers and importers of

portable, industrial and automotive batteries.

The symbol shown below will be on all equipment tted with batteries from 26th September 2008 and indicates they

must NOT be disposed of with other normal waste. Instead, it is the user’s responsibility to dispose of used batteries

by arranging to return them to a designated collection point for the correct recycling.

For more information about where you can send your waste batteries for recycling contact your local authority

ofce.

REGISTERED IN ENGLAND REGISTERED NO. 1711515

REGISTERED OFFICE: BLOCK C 42 BARWELL BUSINESS PARK, CHESSINGTON, SURREY KT9 2NY

viii 420-0025-02UK

TABLE OF CONTENTS

INTRODUCTION iv

1 HANDLING PRECAUTIONS 1

2 PRECAUTIONS REGARDING INSTALLATION LOCATION 4

2-1 LIMITATIONS OF USAGE 5

2-2 OPERATION AREA 6

3

PRECAUTIONS REGARDING PRODUCT OPERATION 8

3-1 BEFORE OPERATION 8

4 PART DESCRIPTIONS 9

5 ACCESSORIES 11

6 ASSEMBLY AND INSTALLATION 12

6-1 INSTALLING THE DISPLAY MOUNTS 15

6-2 INSTALLING THE OVERHEAD DISPLAYS 17

6-3 INSTALLING THE CAMERAS 20

6-4 CABINET POSITIONING 21

6-5 ATTACHING THE ARTWORK TO THE DISPLAYS 22

6-6 ATTACHING THE WIRE COVER BKTS 24

6-7 CONNECTING THE OVERHEAD DISPLAYS (HDMI) 26

6-8 CONNECTING THE OVERHEAD CAMERAS 27

6-9 CONNECTING THE POWER CABLES 28

6-10 CONNECTING THE BILLBOARD LIGHTING CABLES 29

6-11 APPLYING THE WIRE COVERS 31

6-12 ATTACHING THE L&R TOWER ARTWORK 32

6-13 APPLYING POWER & OTHER CONNECTIONS 33

6-14 TURNING ON THE POWER 35

7 PRECAUTIONS WHEN MOVING THE MACHINE 36

8 GRAPHICS DISPLAY 40

8-1 SAFETY PRECAUTIONS WHEN HANDLING THE MONITOR 40

9 PERIODIC INSPECTION 46

ix

10 TROUBLESHOOTING 48

10-1

TROUBLESHOOTING (WHEN NO ERROR MESSAGE IS SHOWN) 48

11 RASBERRY PI CONTROLLER 51

12 DESIGN-RELATED PARTS 53

13 PARTS LIST 54

14 PARTS & SERVICE CONTACT INFORMATION 76

15 WIRE COLOUR CODE TABLE 77

16 WIRING DIAGRAMS 78

HANDLING PRECAUTIONS

1

1

1 HANDLING PRECAUTIONS

When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that

the player can enjoy the game safely.

Non-compliance with the following points or inappropriate handling running counter to the cautionary matters

herein stated can cause personal injury or damage to the machine.

Before performing work, be sure to turn the power off. Performing the work

without turning the power off can cause an electric shock or short circuit.

In cases where work should be performed in the status of power on, this

manual always states to that effect.

To avoid an electric shock or short circuit, do not plug in or unplug quickly.

To avoid an electric shock, do not plug in or unplug with a wet hand.

Do not expose power cords or earth wires on the surface, (oor, passage,

etc.) If exposed, the power cords and earth wires are susceptible to

damage. Damaged cords and wires can cause an electric shock or short

circuit.

To avoid causing a fire or an electric shock, do not put things on or

damage the power cords.

When or after installing the product, do not unnecessarily pull the power

cord. If damaged, the power cord can cause a re or an electric shock.

In case the power cord is damaged, ask for a replacement through where

the product was purchased from or the ofce herein stated. Using the cord

as is damaged can cause re, an electric shock or leakage.

This product MUST be Earthed. Inappropriate Earthing can cause an

electric shock.

Be sure to use fuses meeting the specied rating. Using fuses exceeding

the specied rating can cause a re or an electric shock.

Be sure that connections such as IC BD are made properly. Insufficient

insertion can cause an electric shock.

Specication changes, removal of equipment, conversion and/or addition,

not designated by SEGA are not permitted.

Failure to observe this may cause a fire or an electric shock. Non-

compliance with this instruction can have a bad inuence upon physical

conditions of the players or the onlookers, or result in injury during play.

SEGA shall not be held responsible for damage, compensation for damage

to a third party, caused by specication changes not designated by SEGA.

Do not perform any work or change parts not listed in this manual. Doing

so may lead to an accident.

If you need to perform any work not listed in this manual, request work

from the ofce indicated in this manual or the point of purchase, or inquires

for details.

Be sure to perform periodic maintenance inspections herein stated.

2

HANDLING PRECAUTIONS

1

For the IC board circuit inspections, only the use of a logic tester is

recommended. Using a Multi Tester or General Purpose Tester may result in

damage to IC Circuits. Static electricity from your body may damage some

electronics devices on the IC board. Before handling the IC board, touch a

grounded metallic surface so that the static electricity can be discharged.

Some parts are not designed and manufactured specifically for this game

machine. The manufacturers may discontinue, or change the specications of

such general-purpose parts. If this is the case, SEGA cannot repair or replace

a failed game machine whether or not a warranty period has expired.

CONCERNING THE STICKER DISPLAY

This SEGA product has stickers attached describing the product manufacture No. (Serial No.) and Electrical

Specications. It also has a Sticker describing where to contact for repair and for purchasing parts.

When inquiring about or asking for repairs, mention the Serial No. and Name of Machine indicated on the Sticker.

The Serial Number indicates the product register. Identical machines could have different parts depending on the

date of production. Also, improvements and modifications might have been made after the publication of this

manual. In order to ensure you order the correct parts, mention the Serial No. when contacting the applicable places.

CONCERNING WARNING DISPLAYS

This SEGA product has warning displays on stickers, labels and/or printed instructions adhered/attached to or

incorporated in the places where a potentially hazardous situation could arise. The warning displays are intended

for accident prevention for customers and for avoiding hazardous situations relating to maintenance and servicing

work. Some portions of the cabinet contain high voltage and may cause accidents if touched. When performing

maintenance, be very careful of the warning displays. It is especially important that any complex repair and

replacement work not mentioned herein should be performed by those technical personnel who have knowledge of

electricity and technical expertise.

In order to prevent accidents, caution any customer ignoring the warnings to cease and desist immediately.

VIDEO GAME-INDUCED SEIZURES (VGS) AND PHOTOSENSETIVE EPILEPSY (PSE)

This SEGA product has warning displays on stickers which outline the risk of epilepticform and photosensetive

seizures. These warning displays on stickers are applied close in proximity of the device which may promote

symptoms of either video game-induced seizures or epilepsy. The warning displays are supplied in several languages

and form part of the Installation kit supllied with this product. It is standard practice for the English version of this

label to be applied during manufacture, however it is especially important for the operator to apply the same said

label in the lanuguage of the country of operation.

HANDLING PRECAUTIONS

3

1

STICKER DISPLAY

P.A.T. Label

Rating Label

Serial No Label

WEEE Label

440-WS0010UK

Warning Sticker - High Voltage

440-WS0010UK

Warning Sticker - High Voltage

440-WS0010UK

Warning Sticker - High Voltage

440-WS0010UK

Warning Sticker - High Voltage

440-WS0010UK

Warning Sticker - High Voltage

440-CS0010UK

Caution Sticker

4

PRECAUTIONS REGARDING INSTALLATION LOCATION

2

2 PRECAUTIONS REGARDING INSTALLATION LOCATION

This product is an indoor machine. Do not install it outside. Even indoors, avoid

installing in places mentioned below so as not to cause a fire, electric shock,

injury and/or malfunction.

Places subject to rain or water leakage, or places subject to high humidity in the

proximity of an indoor swimming pool and/or shower, etc.

Places subject to direct sunlight, or places subject to high temperatures in the

proximity of heating units, etc.

Places filled with inflammable gas or vicinity of highly inflammable/volatile

chemicals or hazardous matter.

Dusty places.

Sloped surfaces.

Places subject to any type of violent impact.

Vicinity of anti-disaster facilities such as re exits and re extinguishers.

Areas where the temperature exceeds the applicable temperature (ambient

temperature) range of 5 to 30 degrees centigrade.

Securing a safe area for operation as described in this manual will ensure

safe operation for players and observers.

SEGA shall not be held responsible for damage or compensation for damage

to a third party, resulting from the failure to observe this instruction.

• This product is a companion for the 4 player version of the MARIO &

SONIC at the RIO 2016 OLYMPIC GAMES arcade edition.

• This is not a “Standalone” unit!

• Do not use this product with any other product except for the one which is

attend.

• Secure a suitable area to assemble safely.

• Use a minimum of 2 people with the aid of lifting equipment.

PRECAUTIONS REGARDING INSTALLATION LOCATION

5

2

Be sure to check the Electrical Specifications. Ensure that this product

is compatible with the location's power supply, voltage, and frequency

requirements. A label describing Electrical Specifications is attached to the

product. Non-compliance with the Electrical Specications can cause a re and

electric shock.

This product requires a breaker and earth mechanism as part of the location

facilities. Using the product without these can cause a re and electric shock.

Ensure that the indoor wiring for the power supply is rated at 15 A or higher (AC

single phase 100 V ~ 120 V area), and 7 A or higher (AC 220 V ~ 240 V area). Non-

compliance with the Electrical Specications can cause a re and electric shock.

Be sure to use an independent power supply equipped with an earth leakage

breaker. Using a power supply without an earth leakage breaker can cause an

outbreak of re if a power surge occurs.

Putting many loads on one electrical outlet can cause generation of heat and a

re resulting from overload.

When using an extension cord, ensure that the cord is rated at 15 A or higher (AC

100 V ~ 120 V area) and 7 A or higher (AC 220 V ~ 240 V area). Using a cord rated

lower than the specied rating can cause a re and electric shock.

2-1 LIMITATIONS OF USAGE

6

PRECAUTIONS REGARDING INSTALLATION LOCATION

2

• This product will fit through a standard doorway. Use two people to

advance the Upright Towers through a doorway.

• Do not attempt to move the product by pushing or pulling on the plastic

parts. This may damage the product and my cause personal injury.

• Always use a minimum of two people to maneuver the Upright Towers.

• For the operation of this machine, secure a minimum area of 7.08 m (W) x 2.97m

(D). These dimensions are necessary to enable the customer to walk around

the machine and also to provide adequate ventilation. In such an event, if

a player strikes his or her head, a serious accident may occur, so be sure to

secure the minimum area around the machine specied in this manual.

• Be sure to provide sufficient space specified in this manual. Do not allow

objects to block the ventilation ports. It can cause generation of heat and a

re.

• SEGA shall not be held responsible for damage or compensation for damage

to a third party, resulting from the failure to observe this instruction.

• If the machine does not t through the entryway to the installation location,

do not disassemble it without first consulting the instructions. The machine

should only be disassembled in accordance with the instructions listed in

this manual; do not attempt to disassemble it in any other way. Specic tools

and adjustment procedures are required to assemble and disassemble the

mechanical parts. Attempting to assemble or disassemble the machine

without consulting the instructions may result in accidents during assembly/

disassembly and electric shock, short circuits, and/or personal injury during

operation. If the machine still does not t through the entryway after following

the procedures in this manual, contact your retailer or the ofce listed in this

manual.

• If the machine is still too large to t through the entryway after following the

procedures listed in this manual, do not tip the machine on its side. Attempting

to transport the machine while it is tipped on its side may cause accidents. It

may also damage or warp parts of the machine, resulting in accidents during

operation.

• If the entrance is too narrow, do not tilt the product carelessly. It may be

necessary to carry the product through narrow doorways. If all the product

weight is put on the adjusters at one side only, there could be damage or

deformation, causing serious accidents such as workers getting caught

underneath.

2-2 OPERATION AREA

PRECAUTIONS REGARDING INSTALLATION LOCATION

7

2

OPERATION AREA

750mm

750mm

7,080mm

2,970mm

8

PRECAUTIONS REGARDING PRODUCT OPERATION

3

3

PRECAUTIONS REGARDING PRODUCT OPERATION

In order to prevent accidents and inappropriate behaviour, please check the following before operating the product.

3-1 BEFORE OPERATION

• To ensuremaximum safetyfortheplayers andthecustomers, ensurethat

wheretheproductisoperatedhassufcientlightingtoallowanywarningsto

beread.Operationunderinsufcientlightingmayresultincustomersbumping

intoeachotherortheproductcausinginjury.

• CheckifalltheLegAdjustersareincontactwiththesurface.(Thecasters

shouldberaisedapproximately5mmfromthefloor)Iftheyarenotthe

cabinetwillmoveandmaycausedamagetopropertyorinjurytoaplayeror

observer.

• Donotplaceanyheavyitemsonthisproduct.Doingsomayresultininjuryor

damagetotheproduct.

• Donotclimbonthisproduct.Climbingonthisproductmayresultininjury

or product damage. When checking the upper proportions of this product,

alwaysuseastep/stepladder.

• Toavoidelectricshock,alwayscheckeachdoororservicehatchfordamage

andmakesurethattheyarettedcorrectly.Neveroperatethisproductwith

doorsorservicehatchesremoved.

• Do not place any of the following objects on top of the product, nearby the

product or hang them from the ceiling in close proximity to the product as

doingsomayresultinanelectricshock,shortcircuitordamagetoparts.

• Flower vases, ower pots, cups, glasses, water tanks, cosmetics and/or any

receptacle/container/vesselcontainingliquidorchemicals.

• Besuretoperformappropriateadjustmentofthedisplay(LCDScreen).For

operationofthismachine,donotleavemonitor’sickeringordeviationas

is.Failuretoobservethiscanhaveabadinuenceupontheplayers’orthe

customers’physicalconditions.

• Itissuggestedtoensureaspaceallowingtheplayerswhomayfeelsickwhile

playingthegametotakearest.

• Checkthattheproductislocatedonalevelsurface.Iftheproductisplaced

uponanunevensurfaceitwillrockandcantrapfeetorngersbetweengaps.

PART DESCRIPTIONS

9

4

4 PART DESCRIPTIONS

Upright Main L

42” LCD Display

Marquee LH Panel

Marquee RH PanelMarquee LH UPPER Panel

Marquee MID L UPPER Panel Marquee MID R UPPER Panel

Marquee MID R UPPER Panel

42” LCD Display

Upright Slave R

Camera Camera

10

PART DESCRIPTIONS

4

Display Mount

Assy Elec BD

Assy AC Switch

Assy Block

Lighting

Assy Block

Lighting

Display Mount

Items Width Depth Height

MSR MARQUEE 6,677mm (262.87 in) 887mm (34.92 in) 3204mm (126.14 in)

INSTALLED WEIGHT Appox 400Kg (881.84lb)

ACCESSORIES

11

5

5 ACCESSORIES

Conrm that the accessories listed in the table below are present when setting up the product.

Accessories marked “Spare” in the note column are consumable items but included as spares.

Parts not labeled with part numbers are yet to be assigned. Be sure to handle all parts with care, as some parts are not

available for purchase separately.

Part name/Part no. Description/Use etc. Qty

OWNERS MANUAL

420-0025-02UK

This Manual

1

POWER LEAD

EU

UK

US

Power cord for your region

1

4 WAY NETWORK HUB

1

FLOOR ARTWORK MAT

1

12

ASSEMBLY AND INSTALLATION

6

6 ASSEMBLY AND INSTALLATION

• Perform assembly work by following the procedure herein stated. Failure to

complywiththeinstructionscancauseelectricshock.

• Performassemblingas perthismanual.Sincethisisacomplexmachine,

incorrectassemblingcancauseanelectricshock,machinedamageand/or

improperfunctioningasperspeciedperformance.

• Whenassembling,besuretouseadditionalhelpfromanotherperson(s).

Dependingontheassemblywork,therearesomecasesinwhichworkingby

onepersonalonecancausepersonalinjuryorpartsdamage.

• Adherestrictlytoalloftheworkproceduresstipulatedinthisdocument.Iftwo

or more workers are working at the same time, exercise special caution. If

sequencesarecarriedouterroneously,accidentscanresult.Theremightalso

becasesinwhichtheassemblycannotbecompleted.

• Payspecial attention to thesurroundings when a multiplenumber of workers

areworkingatthesametime.Thereisalwaysthedangerthataworkermight

beinjured.Inassemblyandinstallationofthisproduct,thereareproceduresin

whichastepladderisused,proceduresinwhichheavyobjectsareattached,

andproceduresinvolvingconnectionofaratedpowersupplyof10amperes.

Carelessnessindoingworkcouldleadtograveinjuriesandevenfatalities.

• Ensure that connectors are accurately connected. Incomplete connections

cancauseelectricshock.

• This work should be carried out by the site maintenance personnel or other

qualiedprofessionals.Workperformedbynon-technicalpersonnelcancause

asevereaccidentsuchaselectricshock.Failingtocomplywiththisinstruction

can causeasevereaccidentsuchaselectricshocktotheplayerduring

operation.Ifnoonewithpropertechnologicalexpertiseisavailable,request

servicefromtheofceindicatedinthisdocumentorthepointofpurchaseso

astoensuresafety.

• Becarefulnottodamagethewires.Damagedwiresmaycauseelectricshock

orshortcircuitorpresentariskofre.

• Donotleavepowercableorearthlinesexposedoverpassageways.Exposure

couldleadtodamage,electricshockorshortcircuit.Whereverwiring

has been laid out on a floor surface, use a wiring protection cover. [Wiring

diameter:Powercable,approx.10mm–14mm]

• Persons who connect indoor power supplies must be qualified electricians.

Donotallowanyonewithoutproperqualicationstomakesuchconnections.

Otherwisetherecouldbeelectricshock.

• Providepowercablesforconnectingtheindoorpowersupplytotheproduct.

The rating of the power cable must be at least 15 amperes. The cable must

conformtothisrequirementandalsobeofsufficientlengthtoenablethe

indoorpowersupplytobeconnectedtotheproductwithoutdifculty.Useofa

cablethatdoesnotmeettherequirementscanresultinareorelectricshock.

Therecommendeddimensionsofthepowercableterminalfortheproductuse

areaholediameterof4.5mmandwidthof8mm.

ASSEMBLY AND INSTALLATION

13

6

• For the sake of safety and workability, use 3 core coaxial CE/UL approved

cablesforthepowercables(provided).

• Wheninsertingorremovingaconnector,alwaysholditbyitsmainpart.Ifyou

hold it by anything else while doing so, the connections between wire and

connector terminal fixtures could be damaged; and there could be a short

circuitorre.Therecouldalsobepoorconnectivity.

• Makesurethatalltheadjustersarerestingontheoor.Thecabinetmaymove

andcauseanaccidentiftheadjustersarenotlaidoutproperly.

• Wheneveranyfasteners(e.g.screws,nuts)havebeenlost,alwaysuse

replacement fasteners with proper dimensions as specied in this manual. If

fasteners of any other dimensions are used, it could cause damage and/or

separationofpartsthatresultinsecondaryaccidents.

• Becarefulwhenaligning,attachingormountingpartsso that your head,

hands, fingers, etc., do not get caught in anything. If two or more workers

areworkingatthesametime,exercisespecialcaution.Failuretobe

cautious could result in accidental bone fractures or amputation. Check the

surroundingscarefullybeforeproceeding.

• Whenconnectingwiresinsidethecabinet,theremaybeinstancesinwhichthe

indoorlightingdoesnotreachthatlocation.Haveaashlightorotherauxiliary

lightingequipmentonhand.Ifwiresareconnectedcarelessly,therecouldbe

anaccidentalshortcircuit,re,etc.

• Whentighteningboltsand screws,ensurethatotherparts aresuspended

properly and bolts and screws are fastened tightly. Be sure to take accident

prevention measures such as having another worker support parts. If a part

dropsortopplesoverduringthiswork,aseriousaccidentmayresult.

• Supportandholdpartsinplacesecurelyandfastenthemwithscrewsand/or

bolts.Usetwoworkers,onetosupportthepartandanothertofastenitinplace.

Ifapartisnotsupportedsecurely,itmightfalldown,resultinginanaccident.

• Wear appropriate work clothing so that work can be performed safely. Use

glovesandsafetyshoestopreventaccidentsorinjuries.

• When installing a wire protection cover over a floor, use a material shaped

sothatnoonepassingbywillstumbleoverit.Usingamaterialthatcouldbe

stumbledovermightleadtoanaccidentalfall.

• Becarefulinhandlingplasticparts.Besurenottotightenscrewsornuts

tootightly.Ifsuchpartsareexposedtoexcessiveloadsorimpact,they

might become damaged, resulting in fragments or cracks that could cause

accidentalinjury.

14

ASSEMBLY AND INSTALLATION

6

TOOLS NECESSARY FOR WORK

Phillips Screwdriver (for M4)

Torx T20 Security Driver

Spanner / Adjustable spanner (24mm)

Key Master

Step or Stool

Socket Wrench (13mm)

Hex Key

ASSEMBLY AND INSTALLATION

15

6

6-1 INSTALLING THE DISPLAY MOUNTS

1

Locate parts required to assemble 4x HOLDER LED ASSY MOUNTS. 4x LED ASSY MOUNT (MSR-

5032UK), 4x BKT MARQUEE SUPPORT (MSR 5055UK) and 4x BKT WIRE COVER SUPPORT (MSR-

5057UK).

2

Apply the LED ASSY MOUNT and both BKT WIRE COVER SUPPORTS to the BKT MARQUEE

SUPPORT using the xings shown.

LED ASSY MOUNT

(MSR-5032UK)

BKT MARQUEE SUPPORT

(MSR-5055UK)

M6x20 SKT BH PAS (4)

029-B00620

M6x20 SKT BH PAS (4)

029-B00620

M6 WSHR SPR PAS (4)

060-S00600

M6 WSHR SPR PAS (4)

060-S00600

M6 WSHR 20OD FLT PAS (4)

068-652016

M6 WSHR 20OD FLT PAS (4)

068-652016

BKT WIRE COVER SUPPORT

(MSR-5057UK)

• InstallationoftheDisplaysandDisplayMountsarecarriedoutatheight.These

componentsareheavy.Useaminimumof4peopleandorliftingequipment

such asawinchlift.Alsoprepare ladderstoworkfrom.Whenworkingoff

laddersbesurethattheyarestablewithintheirenvironment.

• Do notattempttoinstalltheDisplaysorDisplaymountswithout theuseof

ladders, lifting equipment or additional help. Trying to install this equipment

withoutaidmayresultininjuryandordamagetoequipment.

16

ASSEMBLY AND INSTALLATION

6

3

Attach the BKT MARQUEE SUP STRETCHER to the top of each cabinet as shown and secure using

xings M6x20 SKT BH PAS (2), M6 WSHR SPR PAS (2) & M6 WSHR 20OD FLT PAS (2)

5

Finally secure the upper section of the LED SUPPORT BKT by tting (2) M6x40 SKT BH PAS Bolts in

locations shown. Proceed to carry out operations 1 to 5 on the remaining 3 cabinets..

4

Offer the now assembled LED DISPLAY MOUNT to the top of each cabinet and over the BKT MARQUEE

SUPPORT STRETCHER. Once in place secure using the xings 6 sets of xings shown.

M6x20 SKT BH PAS (2)

029-B00620

M6x40 SKT BH PAS (6)

029-B00640

M6x40 SKT BH PAS (2)

029-B00640

M6 WSHR SPR PAS (2)

060-S00600

M6 WSHR SPR PAS (6)

060-S00600

M6 WSHR SPR PAS (2)

060-S00600

BKT MARQUEE SUP STRETCHER

MSR-5056UK

M6 WSHR 20OD FLT PAS (2)

068-652016

M6 WSHR 20OD FLT PAS (6)

068-652016

M6 WSHR 20OD FLT PAS (2)

068-652016

+ +

ASSEMBLY AND INSTALLATION

17

6

6-2 INSTALLING THE OVERHEAD DISPLAYS

• InstallationoftheDisplaysandDisplayMountsarecarriedoutatheight.These

componentsareheavy.Useaminimumof4peopleandorliftingequipment

such asawinchlift.Alsoprepare ladderstoworkfrom.Whenworkingoff

laddersbesurethattheyarestablewithintheirenvironment.

• Do notattempttoinstalltheDisplaysorDisplaymountswithout theuseof

ladders, lifting equipment or additional help. Trying to install this equipment

withoutaidmayresultininjuryandordamagetoequipment.

1

Locate (2) BKT LED ASSY SUPPORT (MSR-5122UK) and secure them either side of the MOUNT LED

ASSY CABI (MSR-5121UK) using (4) M8x20 SKT CAP PAS bolts and associated washers.

2

Slide the ASSY 42 LED DISPLAY over and onto the MOUNT LED ASSY CABI and secure using (4)

M8x20 SKT CAP PAS screws and associated washers.

M8x20 SKT BH PAS (4)

020-000820

M8x20 SKT BH PAS (4)

029-000820

MOUNT LED ASSY CABI (1)

MSR-5121UK

MOUNT LED ASSY CABI (1)

MSR-5121UK

ASSY 42 LED DISPLAY(1)

MSR-5100UK

ASSY 42 LED DISPLAY(1)

MSR-5100UK

BKT LED ASSY SUPPORT (2)

MSR-5122UK

M8 WSHR SPR PAS (4)

060-S00800

M8 WSHR SPR PAS (4)

060-S00800

M8 WSHR 20OD FLT PAS (4)

068-852216

M8 WSHR 20OD FLT PAS (4)

068-852216

* Take Care not to damage harnessing when applying the 42 LED DISPLAY to the MOUNT LED ASSY CABI

18

ASSEMBLY AND INSTALLATION

6

3

Each Display is assigned to a different cabinet. The differences are the length of the HDMI cable. Displays

for cabinets 1 and 2 house a 5m HDMI cable whereas displays for cabinets 3 and 4 house a 10m HDMI

cable. The identication tag is applied to the HDMI cable of each display.

4

Using a minimum of 4 people and or lifting equipment. Offer the ASSY 42 LED DISPLAY assigned to

cabinet 1 up to cabinet 1 and slide it carefully into the LED ASSY MOUNT. Take care not to damage any

harnessing when applying the ASSY 42 LED DISPLAY to the CABINET.

5

Once the ASSY 42 LED DISPLAY is fully in position, secure to the LED ASSY MOUNT using (6) M8x20

SKT BH PAS and associated washers.

M8x20 SKT BH PAS (2)

029-B00820

M8x20 SKT BH PAS (4)

029-B00820

M8 WSHR SPR PAS (2)

060-S00800

M8 WSHR SPR PAS (4)

060-S00800

M8 WSHR 20OD FLT PAS (2)

068-852216

M8 WSHR 20OD FLT PAS (4)

068-852216

DVI Cable

LED Display Power Cable

Billboard Lighting Cable

Cabinet ID tag

ASSY 42 LED DISPLAY

LED ASSY MOUNT

ASSEMBLY AND INSTALLATION

19

6

6

Carefully feed the HMDI cable, LED DISPLAY POWER cable and the BILLBOARD LIGHTING cable

from the ASSY 42 LED DISPLAY in through the DISPLAY MOUNT and out to the rear of the cabinet.

7

Repeat steps 1 to 6 on the remaining 3 cabinet.

DVI Cable

LED Display Power Cable

Billboard Lighting Cable

DISPLAY MOUNT

20

ASSEMBLY AND INSTALLATION

6

6-3 INSTALLING THE CAMERAS

1

Locate the ASSY CAMERA and apply it to the underside of the MOUNT ASSY LED CABI as shown.

2

Secure the ASSY CAMERA in place by using (4) M4x16 SKT BH PAS and associated washers..

3

Feed the CAMERA USB cable in through the DISPLAY MOUNT along with the harnesses from the ASSY

42 LED DISPLAY out to the rear of the Cabinet.

Feed the Camera harness in through the access

hole along with the DVI and Power cables

Camera USB Cable

MOUNT ASSY LED CABI

CAMERA USB CABLE

ASSY CAMERA

DISPLAY MOUNT

M4x16 SKT BH PAS (4)

029-B00416

M4 WSHR SPR PAS (4)

060-S00400

M4 WSHR 16OD FLT PAS (4)

068-441616

4

Repeat Steps 1 to 3 in this process to apply all three ASSY CAMERAS to the Cabinets.

ASSEMBLY AND INSTALLATION

21

6

6-4 CABINET POSITIONING

1

To secure an area for operation (Please refer to Section 2 of this manual for dimensions). Space the cabinets

so that the cabinets are evenly spaced (50mm). Align both towers to the outside, with the Main Tower

(POWERED) standing to the Left Hand Side looking from the front.

2

Once all cabinets are in place. Secure them by lowering the Leg levellers to raise the Casters 5mm from

the oor. (Please refer to Section 6-1 of the Mario & Sonic at the 2016 Rio Olympic Games Owners and

Service Manual)

50mm 45mm

45mm 50mm50mm

Rear View

Main Tower (Powered)

Slave Tower

Cabinet 1Cabinet 2Cabinet 3Cabinet 4

22

ASSEMBLY AND INSTALLATION

6

1

The ARTWORK is attached to the BILLBOARD BKTS which are secured to the top of each overhead

display and along both towers.

2

Each piece of artwork is assigned to individual cabinets. For the purpose of illustration we will attach the

Artwork to the rst cabinet (Cabinet 1). All other pieces of artwork in this process are tted in the same

way.

3

Shown below is the artwork and the cabinets they are assigned to.

4

Using 2 people and a set of sturdy Step Ladders, remove the (4) M4x12 SKT BH PAS Machine screws from

the MARQUEE BKT UPPR. Remove the MARQUEE BKT UPPR.

6-5 ATTACHING THE ARTWORK TO THE DISPLAYS

• DonotattempttoinstalltheArtworkwithouttheuseofladders.Tryingtoinstall

this equipment without aid of ladders may result in injury and or damage to

equipment.

Cabinet 1 Cabinet 2 Cabinet 3 Cabinet 4

Unscrew the (4) M4x12 SKT BH

PAS Machine Screws from the

MARQUEE BKT UPPR

MARQUEE BKT UPPR MARQUEE BKT UPPR

ASSEMBLY AND INSTALLATION

23

6

5

Offer Artwork #1 (MSR-5026UK) to Cabinet 1. Replace the MARQUEE BKT UPPR and re-secure using

the (4) M4x12 SKT BH PAS Machine Screws.

6

Repeat processes 1 to 6 until all four cabinet have the artwork xed as shown below.

MARQUEE BKT UPPR

Artwork #1 (MSR-5026UK)

4) M4x12 SKT BH PAS

Machine Screws

24

ASSEMBLY AND INSTALLATION

6

1

Attach BKT LH WIRE COVER REAR (MSR-5047XUK) to the LH TOWER using the xings as shown.

Once the BKT has been attached, pull through the connecting harness.

2

Attach BKT MID WIRE COVER REAR (MSR-5045XUK) to Cabinet 1 and the BKT LH WIRE COVER

REAR using the (6) set of xings as shown.

BKT LH WIRE COVER

MSR-5047XUK

The wire covers connects and spans the full width of all four cabinets and outer towers. Please attach all wire covers

before connecting and routing the harnesses.

IMPORTANT!

Each of the WIRE COVER BKTS are the same for each cabinet with one exception. The WIRE COVER BKT for

the CABINET 2 houses a PI CPU. Please allocate the correct BKT to the correct Cabinet.

6-6 ATTACHING THE WIRE COVER BKTS

LH TOWER ASSY

BKT LH WIRE COVER

MSR-5047XUK

M4x16 SKT BH PAS (6)

029-B00416

M4 WSHR SPR PAS (6)

060-S00400

M4 WSHR 16OD FLT PAS (6)

068-441616

M4x16 SKT BH PAS (2)

029-B00416

M4 WSHR SPR PAS (2)

060-S00400

M4 WSHR 16OD FLT PAS (2)

068-441616

ASSEMBLY AND INSTALLATION

25

6

3

Attach BKT MID WIRE COVER REAR (MSR-5054XUK) to Cabinet 2. (Cabinet 2 BKT MID WIRE

COVER REAR has the PI CPU attached to it). using the xings as shown.

4

Attach BKT MID WIRE COVER REAR (MSR-5054XUK) to Cabinet 3 and Cabinet 4 in the same way as

the BKTS attached in Steps 2 and 3, until all BKT WIRE COVERS have been tted. Finally apply the BKT

RH WIRE COVER REAR to the RH TOWER as instructed in STEP 1.

M4x16 SKT BH PAS (6)

029-B00416

M4 WSHR SPR PAS (6)

060-S00400

M4 WSHR 16OD FLT PAS (6)

068-441616

PI CPU

BKT RH WIRE COVER REAR

MSR-5048XUK

BKT LH WIRE COVER REAR

MSR-5048XUK

BKT MID WIRE COVER REAR

MSR-5054XUK

BKT MID WIRE COVER REAR

MSR-5054XUK

BKT MID WIRE COVER REAR

MSR-5054XUK

BKT MID WIRE COVER REAR

MSR-5054XUK

26

ASSEMBLY AND INSTALLATION

6

LH UPRIGHTRH UPRIGHT

6-7 CONNECTING THE OVERHEAD DISPLAYS (HDMI)

1

Uncoil the (4) HDMI cables from the rear of the Cabinets and trace them through the BKT WIRE COVERS

and down through the ASSY LH TOWER.

2

Using an M4 Socket Drive, remove the Cover panel from the ASSY LH TOWER.

Each OVERHEAD Display is connected to the VIDEO SPLITTER located in the LH TOWER.

VIDEO SPLITTER

HARNESS ROUTE

HARNESS ROUTE

ASSY LH TOWER

ASSEMBLY AND INSTALLATION

27

6

6-8 CONNECTING THE OVERHEAD CAMERAS

1

Uncoil the (4) USB CAMERA cables. The USB CAMERA cables from Cabinets 2 and 3 will connect

directly to the PI CPU. The CAMERA cables from Cabinets 1 and 4 connect to the PI CPU via an

EXTENSION CABLE.

Each OVERHEAD CAMERA is connected to the PI CPU located in the BKT WIRE COVER (CABINET 2)

HARNESS ROUTE

PI CPU

HARNESS ROUTE

LH UPRIGHTRH UPRIGHT

28

ASSEMBLY AND INSTALLATION

6

1

Uncoil the (4) IEC POWER cables from the OVERHEAD DISPLAYS. Locate HARNESSES -

MSR-60103UK, MRS-60109UK, MSR- 60111UK, MSR-60115UK, MST-60116UK, MSR-60117UK and

MSR-60119UK

2

Apply harnesses as shown.

Connecting the POWER cables to the OVERHEAD DISPLAYS, PI CPU and ADJOINING TOWER.

6-9 CONNECTING THE POWER CABLES

HARNESS ROUTE

MSR-60111UKMSR-60116UK

MSR-60109UK

MSR-60119UK

LH UPRIGHTRH UPRIGHT

MSR-60103UKMSR-60117UK

MSR-60115UK

ASSEMBLY AND INSTALLATION

29

6

6-10 CONNECTING THE BILLBOARD LIGHTING CABLES

1

Uncoil the (4) remaining cables. Locate harnesses MSR-60110UK and MSR-60118UK.

Each OVERHEAD DISPLAY is equipped with an LED strip which illuminates the artwork. Please follow the

instructions below to apply these connections.

2

Apply harnesses as shown.

HARNESS ROUTE

LH UPRIGHTRH UPRIGHT

BILLBOARD LIGHTING

MSR-60110UKMSR-60118UK

30

ASSEMBLY AND INSTALLATION

6

For a more detailed diagram of the wiring, please refer to the SCHEMATIC DIAGRAM pages found at the end of

this manual.

3

Once all the harness have been applied, secure them into the routers positioned within the BKT WIRE

COVERS.

4

Ret the outer cover to the ASSY LH TOWER.

ASSEMBLY AND INSTALLATION

31

6

6-11 APPLYING THE WIRE COVERS

Once all the connections have been made and the harnesses secured, attach the WIRE COVERS TO THE BKT

WIRE COVERS.

1

Offer the (4) BKT MID WIRE COVER FRONT (MSR-5046UK) individually up to the BKT MID WIRE

COVER REAR and secure each using (6) M4x16 SKT BH PAS and additional washers. where shown.

BKT OUTER WIRE COVER FRONT

MSR-5049UK (2)

2

Offer the (2) BKT OUTER WIRE COVER FRONT (MSR-5049UK) individually up to the BKT WIRE

COVER REAR on each of the TOWERS. Secure using (6) M4x16 SKT BH PAS and additional washers.

where shown.

M4x16 SKT BH PAS (24)

029-B00416

M4 WSHR SPR PAS (24)

060-S00400

M4 WSHR 16OD FLT PAS (24)

068-441616

BKT MID WIRE COVER FRONT

MSR-5046UK (4)

3

Repeat the above process when attaching the BKT OUTER WIRE COVER FRONT (MSR-5049UK) to the

RH TOWER.

32

ASSEMBLY AND INSTALLATION

6

6-12 ATTACHING THE L&R TOWER ARTWORK

Each Tower has it’s own Artwork which complete the scene running across the top of all 6 cabinets (inc Towers).

Follow the instructions below on tting the L&R TOWER Artwork.

For the purpose of these instructions we shall apply the Artwork to the LH TOWER. Parts and processes will remain

the same for the opposing Tower.

1Locate the ASSY MARQUEE LEFT HAND PANEL.

2Apply the ASSY MARQUEE LH PANEL to the LH Tower. Fix and secure using (8) M4x16 SKT BH PAS

machine Screws in locations shown.

3Follow the same process as above to apply the ASSY MARQUEE RH PANEL to the RH TOWER.

ASSY MARQUEE LH PANEL

MSR-5010UK

ASSY MARQUEE LH PANEL

MSR-5010UK

ASSY MARQUEE RH PANEL

MSR-5015UK

M4x16 SKT BH PAS (6)

029-B00416

M4 WSHR SPR PAS (6)

060-S00400

M4 WSHR 16OD FLT PAS (6)

068-441616

ASSEMBLY AND INSTALLATION

33

6

• Usethepowersupplyequippedwithanearthleakagebreaker.Useofpower

supplywithoutsuchabreakercouldresultinreifthereisacurrentleakage.

• Have available a securely grounded indoor ground terminal. Without proper

grounding, customers could be electrocuted and product operations might

notalwaysbestable.

• Donotexposethepowercordorgroundwire.Iftheseareexposed,customers

couldstumbleoverthem,forinstance,andeasilydamagethem.Additionally,

iftheselines are damaged, there could bearisk of electrical shock or short

circuit.Settheselinesatlocationswheretheywillnotinterferewithcustomer

trafc,orattachcoverstothem.

• Afterlayingoutthepowercordontheoor,besuretoalwaysprotectit.Ifthe

power cord is left exposed, it can easily be damaged, resulting in electrical

shock.

Mains Switch shown in

OFF position

Mains ON/OFF Switch

IEC Inlet

6-13 APPLYING POWER & OTHER CONNECTIONS

1

Conrm that the MAINS SW is in the OFF position.

34

ASSEMBLY AND INSTALLATION

6

2

Fully insert the power cord connector on the side opposite the power plug into the AC unit IEC inlet. Insert

the power cord plug into the outlet.

3

The power cord is laid out indoors. Protect the power cord by attaching a wire cover to it.

Wire Cover

ASSEMBLY AND INSTALLATION

35

6

• Set the main switch of the AC unit to ON and engage the power.

• When you turn on the power, the TOWER LED’s will illuminate and fade in and out of colours.

• The BILLBOARD lighting will illuminate.

• The OVERHEAD DISPLAYS will turn on and display a boot sequence.

• The OVERHEAD DISPLAYS will display a MARIO & SONIC advertisement screen.

• During the advertisement sequence of the OVERHEAD DISPLAY the CAMERA positions will be show.

Please refer to the MARIO & SONIC at the 2016 RIO OLYMPIC GAMES ARCADE EDITION Owners manual

for changes to the Game cabinets when power is applied.

6-14 TURNING ON THE POWER

COMPONENTS WHICH CHANGE STATE WHEN POWER IS APPLIED

Billboard lighting illuminates

Overhead Displays show advertising screen.

Left & Right towers fade colours in and out

36

PRECAUTIONS WHEN MOVING THE MACHINE

7

7 PRECAUTIONS WHEN MOVING THE MACHINE

• Asusedintheseinstructions,theterm“moving”referstomovingoftheproduct

withinthesamebuilding,storeorfacility. Theseinstructionsdonot cover

moving between different buildings, areas, stores or facilities, since diverse

factorsareinvolved,notonlypackagingbutalsoloadingontotransport

vehicles,and securingtheproductin placeduringtransport.To transportthe

producttoadifferentbuildingorstore,contactthevendorwheretheproduct

was purchased or the office indicated in these instructions. Or request that

moving be done for you. This product is made up of parts that are of large

sizeandheavyweight.Unlessworkisentrustedtosomeonewithexpertisein

packagingandtransportofsuchparts,aseriousaccidentmightoccur.

• Evenwhentheproductistobemovedwithinthesamebuilding,store

orfacility,contactthepointofpurchaseortheofficeindicatedinthese

instructions if there will be level differences or narrow or low level entrances

whilemoving.Orrequestthatmovingbedoneforyou.Neverdisassemblethe

productinanywaynotcoveredintheseinstructions.Otherwisetherecouldbe

are,electricshockand/orshortcircuit.

• Alwaysdisconnectthepowercablebeforemovingtheproduct.Ifitismoved

withthepowercableconnected,thecablecouldbedamaged,causingre

orelectricshock.

• Aqualiedelectricianisrequiredformovingproductpartswithinastoreand

forchangingindoorwiring.Donothaveworkperformedbyanyonewhoisnot

qualied.Otherwisetherecouldbeelectricshock.

• Haveworkperformedbysitemaintenancepersonnelorotherqualified

individuals. Donotallowpeoplewithoutproper knowledgeandtechnical

expertisetoworkontheproduct.Otherwisetherecouldbeanelectricshock

orotherseriousaccident.Also,customerscouldbeinjuredwhileoperatingthe

product.

• Donot try tomovethisproduct while itisstillassembled. Always removethe

Billboardandsplitthecabinetsbeforemoving.

• Becauseitisstructurallydifcultforexteriorlightingtoenterthecabinet,have

auxiliary lighting available. Working within a dark environment can lead to

accidents.

• Forinstructionsonseparationanddisassemblyofthecabinet,refertoChapter

6ofthismanual.Failuretofollowtheinstructionsgivenbythismanualleavesa

highriskofaccidentssuchaselectricshockoccurring.

• Proceedwithchecksandtasksasindicatedintheseinstructions.Ifinstructions

arenotfollowed,oriftasksand/orchecksareneglected,anelectricshockor

otherveryseriousaccident,evenfatalaccident,canoccur.Also,customers

couldbeinjuredwhileoperatingtheproduct.

• Be carefulnottodamagewiring.Beforeseparatingpartsthathavewiring

connections, disconnect the wiring connections, unravel wire bundles and

undofastenings.Onlyafterthat,removefasteners(screws,nuts,etc.).Ifwiring

becomesdamaged,therecouldbeanelectricshock,shortcircuitorre.

PRECAUTIONS WHEN MOVING THE MACHINE

37

7

• Ifmovingthroughadoororplacesthatmaybecomenarrow,i.ecorridorsor

placeswhichhavelowceilingssuchasanelevator,youshouldremovethe

billboard.

• Wheninsertingorremovingaconnector,alwaysholditbyitsmainpart.Ifyou

hold it by anything else while doing so, the connections between wire and

connector terminal fixtures could be damaged; and there could be a short

circuitorre.Therecouldalsobepoorconnectivity.

• Do not move unit with the adjusters in contact with the oor. Otherwise parts

mightbedamagedordeformedandtheremightbeaccidents.

• Wheneveranyfasteners(e.g.screws,nuts)havebeenlost,alwaysuse

replacement fasteners with proper dimensions as specied in this manual. If

fasteners of any other dimensions are used, it could cause damage and/or

separationofpartsthatresultinsecondaryaccidents.

• Donotplacethecabinetoninclinesorunevensurfaces.Thiscouldresultinthe

unitfallingover.

• Checksurroundings carefullywhilemovingthe unit. Ifyoushouldget caught

betweentheunitandawall,forinstance,therecouldbeaseriousaccident.

• Haveonhandanumberofworkersappropriateforeachtaskthatneedstobe

done. Make calculations by approximating that one worker can lift roughly

15kgofweight.Ifaninsufcientnumberofworkerstrytoliftaheavyobject,

itcouldresultinaworkerstumblingandtheobjectbeingdropped,crushing

someoneorsomethingunderneath.Workerscouldalsoinjuretheirbacks,etc.

• When lifting a heavy object, be sure to carefully consider the area where it

willbelifted.Ifpossible,lifttheobjectbyitshandlesorbase.Ifweakfasteners

or fragilepartsaregripped, theycouldbedamagedunderthe weightof

the object, and this could result in a worker stumbling and the object being

dropped,causingpersonalinjury.

• Neverdisassembletheunitinwaysotherthanthosedescribedinthismanual.

Doingsocancauseaccidentssuchaselectricshocks,shortcircuits,andres.

• Donotattempttotilttheunittotitthroughnarrowdoorways.Movingtheunit

whileitistiltedcanresultinanaccident.Itcanalsocausedeformationsand

damage to parts, as well as deviations of fastening positions, which could

resultinaccidentsduringoperation.

38

PRECAUTIONS WHEN MOVING THE MACHINE

7

• Donotpushplasticpartsoranypartassociatedwiththemovingmechanism.

Donotliftorsupporttheproductbyanyplasticpart.Partscanbedamaged,

andfragmentscancauseinjury.

• DonotpushonorholdontotheLCDorcontrollerstomovetheunit.Doingso

couldbreakthepartsandleadtopeoplegettinginjured..

• Donotstackpartsthathavebeenseparatedordisassembledindiscriminately.

Thesurfaceofthepartscouldbedamagedordeformed.Significant

deformationscanresultinimproperoperationandbreakdowns.

• Do not lean separated or disassembled parts against a wall or other surface

indiscriminately. The parts could be deformed. Accidents could also occur

shouldthepartsfallover.

• Donothold onto the controllers to use asaleveror leverage. Doing so may

causedamageresultingininjurytotheplayerorimpairedgameplay.

• If the unit is moved over oor surfaces where there is carpet, decorative

panel,etc.,theremightbefrictionorsoiling.

• Movementbycasterscandamagethefloor,dependingonthefloor

material.Haveamatorthinplateavailableformovingcasters.Ifrugs,for

instance,havebeenlaidout,removethembeforemoving.

• Becarefulnottodamagedelicatepartsastherearseatmoulding/

billboard end caps etc whilst moving the product. Always push/pull the

productleveringfromtheboltedonmetalpartsorbythelowersections

suchasthebase.

• Donotapplyropedirectlytotheproduct’ssurface.Useprotective

material at locations where rope is applied taking care not to damage

componentsattachedtothemachine.

• Thestrengthofthisproduct’sjointswerenotdesignedsuchthatthe

productcanbemovedwhileassembled.Attemptingtopushonthe

cockpit, etc. to move the unit while assembled can result in damage,

deformation,andmisalignmentofthejoints.Abnormalitiesinthejointscan

resultinimproperoperationorbreakdownininternalmechanisms.

PRECAUTIONS WHEN MOVING THE MACHINE

39

7

It is not recommended to move or try to move this machine once assembled. If there is no other alternative but to

move the machine, then a complete disassemble will be required. Follow the instructions in section 6 of this manual

and in the MARIO & SONIC at the RIO 2016 OLYMPIC GAMES ARCADE EDITION Owners manual in reverse

order in order to dismantle this machine safely.

Billboard Panels

Overhead Displays

Supports

Display Mounts

Tower L Tower R

Game Cabinets

40

GRAPHICS DISPLAY

8

Responding to breakdown or abnormality

● Ifsmokeorastrangeodorappears,immediatelyunplugthepowercablefrom

 thepowersource.

 Continuingtousetheproductmaycauseareoranelectricshock.Ensure

 thatsmokeisnolongeremitted,andcontactthepointofpurchase.

● Ifnothingdisplaysonthescreen,immediatelyunplugthepowercablefrom

 thepowersource.

 Continuingtousetheproductmaycauseareoranelectricshock.Contact

 thepointofpurchaseandrequestaninspection.

● Ifwateroraforeignobjectentersthemonitor’sinterior,immediatelyunplugthe

 powercablefromthepowersource.

 Continuingtousetheproductmaycauseareoranelectricshock.Contact

 thepointofpurchaseandrequestaninspection.

● Ifthemonitorisdroppedorthecabinetisdamaged,immediatelyunplugthe

 powercablefromthepowersource.

 Continuingtousetheproductmaycauseareoranelectricshock.Contact

 thepointofpurchaseandrequestaninspection.

 Duringoperation

● Donotrepair,reconstruct,ordisassemblethemonitor.

 Themonitorsinteriorcontainshighvoltageparts.Areoranelectricshock

 couldresult.

 Forinspections,adjustments,andrepairofthemonitorsinterior,requestwork

 fromthepointofpurchase.

● Donotinsertforeignobjects.

 Ifmetalobjectsorammablematerialssuchaspaperareinsertedintothe

 interiorthroughventilationopeningsorotherapertures,anelectricshockcould

 result.

● Intheeventofathunderstorm,donottouchtheproductorthepowercable.

 Anelectricshockcouldresult.

● Makesuretoperformappropriateadjustments.Donotoperate  

 theproductwhenthescreenisickering,distorted,orexperiencingother 

 abnormalities.Imagesfromanimproperlyadjustedscreencouldcause 

 playersandothercustomerstoexperiencedizziness,headaches,andother

 ailments.

8-1 SAFETY PRECAUTIONS WHEN HANDLING THE MONITOR

8 GRAPHICS DISPLAY

GRAPHICS DISPLAY

41

8

CLEAN THE SCREEN DAILY.

8-2 CLEANING THE SCREEN SURFACE

● Useasoft,drycloth(annel-type)towipeawaydirt.Donotusematerialssuch

ascoarsemeshgauze.

● Alcohol(ethanol)istherecommendedsolventforremovingdirt.Whenusinga

cleaningagent,followtheprecautionsbelow.

- Diluteneutralcleaningagentsforhomeusewithwater.Soakasoftclothinthe

solution,andwringitthoroughlybeforewipingthescreen.

- Donotuseabrasivecleaningagentsorpowders,orcleaningagents 

containingbleach.

- Donotusealkalinecleaningagentssuchasglasscleaners,orsolventssuchas

thinners.

● Donotscruborscratchthescreensurfacewithabrasivematerialssuchas

brushesorscrubbrushes.

42

GRAPHICS DISPLAY

8

CONTROL - ADJUSTMENT PROCEDURE

This sections explains basic control procedures for making adjustments using the buttons on

the 'Monitor Adjustment Board'

This Adjustment Board is located on the underside of each OVERHEAD DISPLAY. Using an Allen Key Wrench.

undo the (2) M4x12 SKT BH Machine Screws and remove the OSD Controller BKT.

8-3 ADJUSTMENT METHOD

All adjustmentvaluesaresetaccuratelyatthetimeofshippingfromthe

factory. Do not readjust these values needlessly or apply adjustments not

specied in this manual. The display may not appear properly if the values

areincorrect.

OSD Control Bd

OSD Control Bd Bkt

M4x12 SKT BH PAS Machine Screw

Although each display is congured prior despatch it may be possible that the settings may be lost for one reason or another.

If this is the case then please ensure that the SOURCE is set to DVI and the AUTO SCAN feature is turned off.

Once the image is displayed the AUTO SET UP button may be pressed. This only is required to be carried out just the once if

all settings are lost.

IMPORTANT

GRAPHICS DISPLAY

43

8

Button Names and Functions

MENU: Turn the Picture Menu display ON and OFF.

SELECT: Gains entry to the Item selected in the menu. (Highlights in Yellow when selected)

Exits the Item adustment. Any changes made during this

operation are actioned.

DOWN: Moves the cursor (Black Bar) down to select a menu item.

Decrease the value of, or change, a selected menu item.

UP: Move the cursor (Black Bar) up to select a menu item.

Increase the value of, or change, a selected menu item.

LED: LED illuminates green: Monitor is operating.

LED ashes red: Power is off.

POWER: Turns the LCD Display ON and OFF. (Usually, it’s not necessary to operate.)

44

GRAPHICS DISPLAY

8

On-Screen Display (OSD)

Press the MENU Button while the OSD is not displayed to bring up the Picture Menu.

On the Picture Menu, it is possible to perform various screen adjustments.

Use the UP and DOWN Buttons to move the ‘Black Bar’to the item you want to adjust.

After selecting the desired item, pressing the SELECT Button will extend the MENU Screen and allow

adjustments to be changed.

Within each item, press the SELECT Button to exit the adjustment screen. The adjustment values at this time will be

saved simultaneously.

The current options are set at :

CSM - 6500K

Brightness - 100

Contrast - 50

GRAPHICS DISPLAY

45

8

On-Screen Display (OSD) <continued>

Available Settings

CSM (Selects Operation Mode))

Selection availble - 6500K - 9300K - USER

BRIGHTNESS (Adjust Brightness)

Adjust screen Brightness. - Values: 0 - 100

(0” being the darkest setting, and “100” being the brightest)

CONTRAST (Adjust Contrast)

Adjust Contrast level. - Values: 0 - 100

(0” having the least amount of difference between light and dark, and “100” having the most)

NOTE : The Red, Green, and Blue adjustments are unavailable in the Mode of Operation selected on the Screen

shown in 11-3 Fig. 06. These adjustments can only be made is the CSM option is set to ‘User’.

9

PERIODIC INSPECTION

46

• Every6monthschecktoseeifpowercordsaredamaged,theplugissecurely

inserted,dustisaccumulatedbetweenthesocketoutletandthepowerplug,

etc. Dust will accumulated if using the product regularly. Continued use with

thepresenceofaccumulateddustmayresultinareandorelectricshock.

• Thereisthedangerofaccidentsinvolvingelectricalshortscircuitsorfire

caused byfactorssuchasthedeteriorationof insulationinelectricaland

electronicequipment over time. Check that there are no abnormalities such

asodorsfromburning.

• For allnormalmaintenanceprocedures,alwaysturnoffthepowerbefore

beginning.Startingtheprocedureswiththepowerstilloncanresultinelectric

shocksorshortcircuits.

• Whenrestoringpoweraftermaintenanceiscompletedorgoingintoorcoming

outoftheTestMode,besuretoverifythattherearenopeoplenearthe

product. When the power is restored or when coming out of Test Mode, the

productwillautomaticallyundergoinitializationoperation.Ifpeoplearenear

theproduct,itcouldresultinanaccidentinvolvingthemovingmechanism.

• In the event that parts related to the ride mechanisms (motors or reducers,

etc.)aredamagedorbreakdown,orwhenpartsreplacementorrepairsare

needed,requestworkbedonebythepointofpurchaseortheofcelistedin

thismanual.Suchproceduresrequirespecializedknowledge,techniques,and

tools.Improperlyperformedprocedurescanresultinaccidents.

• Do not use a water jet (high pressure washing device) or hose to clean this

product. It was not designed to be cleaned by a water jet. Water could get

inside and cause electrocution or short circuits. The product could also be

damagedinsuchawaythatitisdifculttorepair.

The items listed below require periodic check and maintenance to retain the performance of this machine and to

ensure safe business operation.

When handling the controller, the player will be in direct contact with it. In order to always allow the player to enjoy

the game, be sure to clean it regularly. Also, it is advisable to provide wet tissue, etc. available for player use.

9 PERIODIC INSPECTION

• Becarefulnottogetyourngerscaughtwhenopening/closingorattaching/

removingdoors,lidsandothersuchparts.

• When working inside the cabinet, you could get caught on parts or scratch

yourselfonthem.Checktheinsideofthecabinetandbeawareofwherethe

partsarebeforeperformingthework.

PERIODIC INSPECTION

9

47

PERIOD ITEMS DESCRIPTION

As appropriate CABINET SURFACE Cleaning

LAMPS Inspection

Daily TOWER L&R Conrm adjusters contact oor

Weekly LCD Screen Cleaning

Check monitor adjustment

Monthly TOWER L&R Check LED operation

BILLBOARD Check LED operation

CAMERA Check alignment and focus

Every 3 Months TOWER Inspect outer xings

Inspect acrylics.

OVERHEAD DISPLAYS Inspect xings

Inspect stability

1 year INSIDE TOWER L&R Cleaning

POWER PLUG Inspection, Cleaning

OUTER TOWER L&R Cleaning

PERIODICINSPECTIONTABLE

Cleaning the Cabinet Surfaces

When the cabinet surfaces are badly soiled, remove stains with a soft cloth dipped in water or diluted with a

chemical detergent and squeezed dry. To avoid damaging surface nish, do not use such solvents as thinner, benzine,

etc. other than ethyl alcohol, or abrasives, bleaching agent and chemical dustcloth.

Some general-purpose household, kitchen and furniture cleaning products may contain strong solvents that degrade

plastic components, coatings, and print. Before using any cleaning product, read the product's cautionary notes

carefully and test the product rst on a small area that is not highly visible.

DISPLAY (LCD SCREEN Cleaning)

When the Display LCD Screen surfaces are dirty, smudges or greasey, gently wipe the display with a dry, lint-free,

soft cloth. If you see a scratch-like mark on your display, it might be a stain which has been transfered from food like

matter when the screen was depressed from the outside To avoid damaging surface nish, do not use such solvents

as thinner, benzine, etc. the same applies to ethyl alcohol, or abrasives, bleaching agent and chemical dustcloths.

Wipe or dust the stain gently with a dry, soft cloth. If the stain remains, moisten a lint-free, soft cloth with water or

a 50-50 mixture of isopropyl alcohol and water that does not contain impurities. Wring out as much of the liquid as

possible and wipe the display again; do not let any liquid drip from the cloth.

Antistatic and purpose made LCD cleaning wipes are also acceptable alternatives.

IsopropylAlcoholisaammableliquid.

Donotusethiscleanernearanexposedameorcleanthescreenwhenitis

poweredon..

10

TROUBLESHOOTING

48

10-1

TROUBLESHOOTING (WHEN NO ERROR MESSAGE IS SHOWN)

• In order to prevent electric shock and short circuit, be sure to turn power off

beforeperformingwork.

• Becareful so as notto damage wirings. Damaged wiring can causeelectric

shockorshortcircuit.

• After removing the cause of the functioning of the Circuit Protector, reinstate

theCircuitProtector.Dependingonthecauseofthefunctioning,usingtheCircuit

Protectorasiswithoutremovingthecausecancausegenerationofheatandre

hazard.

• Intheeventthataproblemcannotberesolvedbyemployingtheprocedures

listed inthisManual,besuretorequestservicefromtheofficeshownonthis

Manualorthedealerfromwhomtheproductwasoriginallypurchased.Attempts

toemployproceduresotherthanthosespecifiedinthisManualcancause

electricalshock,shorting,orre.

• In the event of a problem that is not described here, be sure to contact the

ofceshownonthisManualorthedealerfromwhomtheproduct wasoriginally

purchased.Carelessattemptsatrepaircanresultinelectricalshock,shorting,or

re.

10 TROUBLESHOOTING

• Incasefusereplacementsotherthanthosestatedinthismanualare

necessary,contactwhereyoupurchasedtheproductfromforinquiries

regardingthismatter.

• Inordertopreventanelectricshock,besuretoturnpoweroffandunplugfrom

thesocketoutletbeforeperformingworkbytouchingtheinternalpartsofthe

product.

• Becareful so as notto damage wirings. Damaged wiring can causeelectric

shockandshortcircuitaccidents.

• Besuretousefusesmeetingspecifiedrating.Usingfusesexceedingthe

speciedratingcancausereandelectricshockaccidents.

• Aftereliminatingthecauseoftheblowingoffuse,replacethefuse.Depending

on the cause of fuse blowing, continued use with the fuse as is blown can

causegenerationofheatandrehazard.

Replacing Fuses

TROUBLESHOOTING

10

49

10

TROUBLESHOOTING

50

PROBLEM CAUSE COUNTERMEASURE

With main switch ON there

is no activation

Power is not supplied Insert power lead all the way into

outlet

Supply voltage is not correct Make sure that supply voltage is

correct

Circuit protector activated Reset circuit protector/replace

fuse

There is lighting but no

video signal

Video signal connector or

monitor power connector is

not properly connected

Check connections of the monitor

and at the PI and Video Splitter

Incorrect colour on

monitor

Poor connection of video

cable

Conrm connection of video/VGA

cable.

Monitor fault Contact point of purchase

Screen saturation and

brightness not correct

Screen not properly adjusted Adjust screen settings

Video displays are lit but

no graphic are displayed

on screen..

Poor connection of

connectors

Check connection at Splitter

No Video software on PI cpu Check the Micro SD Card in PI

LEDs in the Towers not

operating

LED Controller is not switched

on.

Press the power bottom on the

LED controller

Connections at the LED

Controller are bad

Check and re-sit the connections

at the LED controller.

Billboard displays not

illuminating.

Bad connection between

Billboard LED and PSU

Check connections between

Billboard and PSU.

Disconnect and reconnect

connections where possible.

Overhead displays do

not show attraction video

footage.

Overhead display congured

incorrectly.

Check the source for the

overhead displays is set to DVI

Disable the autoscan feature on

the overhead displays.

The Cameras do not show

in the correct sequence

The connection to the PI

controller are incorrect.

Disconnect the Camera USB

cables to the PI Controller and

reposition them in the correct

sequence.

The Cameras are not

operational.

The connections to the PI

controller is bad.

Check connections to and from

the Camera to the PI controller.

The Camera shows an out

of focus image.

The focus adjustment on the

Camera is incorrect.

Adjust the Camera focus.

The is dirt or an obstruction in

front of the camera lens

Clean the camera lens

Any problems found outside the description of this troubleshooter, please contact your local service department

GAME BOARD

51

11

• Whenworkingwiththeproduct,besuretoturnthepoweroff.Workingwiththe

poweronmaycauseanelectricshockorshortcircuit.

• Be careful not to damage the wires. Damaged wires may cause an electric

shock,shortcircuitorpresentariskofre.

• Donotusethisproductwithconnectorsotherthanthosethatwereconnected

andusedwiththeCPUatthetimeofshipping.Donotcarelesslyconnectwires

to connectors that were not used at the time of shipping, as this may cause

overheating,smokeorredamage.

Static electricityfromyourbody maydamagesomeelectronics devices

on the IC board. Before handling the IC board, touch a grounded metallic

surfacesothatthestaticelectricitycanbedischarged.

11 RASBERRY PI CONTROLLER

16-1 HANDLING PRECAUTIONS

● TopreventelectricshockorICBoardmalfunctioning,besuretoturnoffthe

powerforthecabinetwheninstallingorremovingtheICBoard.

● ExtraneousmattersuchasdustontheICBoardcancausetheICBoardto

generateheatandresultinareduetoshortcircuit,etc.EnsuretheICBoard

surfacesarealwayskeptclean.

● BesuretoconnecttheICBoardandconnectorscompletely.Insufcient

insertioncandamageICBoard,etc.

● FortheICBoardcircuitinspection,onlytheuseofLogicTesterispermitted.The

useofordinarytestersisnotpermittedasthesecandamagetheICBoard.

● DonotsubjecttheICBoardtostaticelectricitywheninstallingtheICBoardin

thecabinetorwhenconnectingwireharnessconnectorstotheICBoard.

● Whensolderingbuttons,etc.tothewireharnesses,besuretoremovethewire

harnessesfromtheICBoardsoasnottosubjecttheICBoardtoheat.

● Somepartsaretheonesdesignedandmanufacturednotspecicallyforthis

product.Themanufacturersmaydiscontinue,orchangethespecicationsof,

suchgeneral-purposeparts.Ifthisisthecase,SEGAcannotrepairorreplacea

failedproductwhetherornotawarrantyperiodhasexpired.

52

GAME BOARD

11

11-2 PARTS DETAILS & CONNECTIONS

11-3 CAMERA TEST FUNCTION

USB Connectors

(Camera Positions)

LAN Connection

(Not used)

3.5mm Jack

(Not used)

DVI Connection

(Dislpays)

Micro USB

(Power)

MICRO SD CARD Port

(Software)

Multi Connector

(Power & Inputs)

The CAMERA TEST can be accessed by pressing the single button attached to the INPUT CONNECTOR on the PI

Controller.

1

Conrm that the MAINS SW is in the ON position.

2

Press the PI TEST button.

3

The OVERHEAD displays will show a CAMERA TEST routing.

4

All OVERHEAD displays will show the output from CAMERA 1 for a limited time before advancing to

CAMERA 2 and so on until all 4 CAMERAS signals have been displayed.

5

Once the 4th CAMERA has been display on the OVERHEAD screens, press the PI Controller TEST button

to EXIT.

DESIGN - RELATED PARTS

53

12

12 DESIGN-RELATED PARTS

MSR-5058UK

MSR-5010UK

MSR-5006UKMSR-5005UK

MSR-5020UK MSR-5021UK MSR-5022UK MSR-5023UK

MSR-5015UK

54

PARTS LIST

13

13 PARTS LIST

ASSY TOP MARIO & SONIC MARQUEE 4P

MSR-5000XUK

TOP ASSY MARIO & SONIC MARQUEE 4P

* ** ***

MSR-5001XUK

ASSY MARQUEE MSR-5060UK DSD-5021UK x3

ASSY MARQUEE UPRIGHT LH ASSY BLOCK LIGHTING

MSR-5400UK

ASSY MARQ ELEC BOARD LH

DSD-5700UK

ASSY AC SWITCH

MSR-5070UK DSD-5021UK x3

ASSY MARQUEE UPRIGHT RH ASSY BLOCK LIGHTING

MSR-INST-MARQ-XUK MSR-5010UK

ASSY INST KIT MARQUEE ASSY MARQUEE LH PANEL

MSR-5015UK

ASSY MARQUEE RH PANEL

MSR-5020UK

ASSY MARQ LH UPPER PNL

MSR-5021UK

ASSY MARQ MID L UPPER PNL

MSR-5022UK

ASSY MARQ MID R UPPER PNL

MSR-5023UK

ASSY MARQ RH UPPER PNL

MSR-5100UK x4

ASSY 42 LED ASSY

MSR-5120UK x4

ASSY LED DISPLAY MOUNT

MSR-5080UK x4

ASSY CAMERA MOUNT

55

PARTS LIST

13

1 ASSY TOP MARIO & SONIC MARQUEE (MSR-5000XUK) (D-1/1)

ITEM NO PART NO DESCRIPTION QTY

*1 MSR-5001XUK ASSY MARQUEE 1

*20 421-7988-91UK STICKER SERIAL NUMBER UK 2

*21 440-WS0010UK LABEL WARNING HI-VOLTAGE 2

*22 440-WS0030UK LABEL WARNING CAUTION 2

*23 LB1046 LABEL TESTED FOR ELEC. SAFETY 1

*24 LB1130 LABEL WEEE WHEELIE BIN 1

*308 MSR-60119UK WH Pi POWER EXTN 1

*401 MSR-INST-MARQ-XUK ASSY INST KIT MSR MARQUEE 1

*410 PK0505 PALLET MSR MARQUEE 1

*411 PK0484 SHRINK WRAP DV DX 1

*401 DV-INST-D ASSY INST DV DX 1

*410 PK0483 PALLET DV DX 1

*411 PK0484 SHRINK WRAP DV DX 1

Please refer to HANDLING PRECAUTIONS (Section 1 of this manual) for locations of Labels.

1

401

56

PARTS LIST

13

2 ASSY MARQUEE (MSR-5001XUK) (D-1/1)

ITEM NO PART NO DESCRIPTION QTY

**1 MSR-5060UK ASSY MARQUEE UPRIGHT LH 1

**2 MSR-5070UK ASSY MARQUEE UPRIGHT RH 1

**3 MSR-5032XUK HOLDER LED ASSY MOUNT 4

**4 MSR-5055UK BRKT MARQUEE SUPPORT 8

**5 MSR-5056UK BRKT MARQUEE SUPPORT STRETCHER 4

**6 MSR-5057UK BRKT WIRE COVER SUPPPORT 8

**201 029-B00620 M6X20 SKT BH PAS 64

**202 060-S00600 M6 WSHR SPR PAS 64

**203 068-652016 M6 WSHR 20OD FLT PAS 64

12

5

3

4

6

201

201

201 202 203

202 203

202

203

57

PARTS LIST

13

3 ASSY MARQUEE UPRIGHT L (MSR-5060UK) (D-1/2)

1

23

4

6

5

7

8

9

10

11

101

102

103

201

201

201

201

201

201

201

202

203

204

204

205

205

206

206

206

206

206

206

206

207

207

58

PARTS LIST

13

3 ASSY MARQUEE UPRIGHT L (MSR-5060UK) (D-2/2)

ITEM PART NO DESCRIPTION QTY

***1 DSD-5021UK ASSY BLOCK LIGHTING 3

***2 MSR-5400UK ASSY MARQUEE ELEC BOARD LH 1

***3 DSD-5700UK ASSY AC SWITCH 1

***4 MSR-5002UK FRAME MARQUEE UPRIGHT 1

***5 MSR-5003UK CAP MARQUEE FRAME UPRIGHT 1

***6 MSR-5004UK COVER UPRIGHT FOOT 1

***7 MSR-5005UK PANEL UPRIGHT FRONT 2

****1 MSR-5005-AUK BLANK UPRIGHT FRONT PANEL 1

***8 MSR-5006UK PANEL UPRIGHT SIDE 4

****1 MSR-5006-AUK BLANK UPRIGHT SIDE PANEL 1

***9 MSR-5009UK COVER MARQUEE UPRIGHT 1

***10 MSR-5036UK PANEL MARQUEE ELEC ACCESS 1

***11 MSR-5061UK PANEL UPRIGHT LIGHTING MOUNT 4

***101 601-0004UK-01 LEG ADJ M16X100x70DIA LNUT 4

***102 FN1012 FAN GUARD METAL 120MM (FG-12) 3

***103 260-0012-01UK FAN DC 12V ROHS 1

***201 029-B00416 M4X16 SKT BH PAS 114

***202 008-B00450 M4X50 TMP BH PAS 4

***203 029-B00425 M4X25 SKT BH PAS 4

***204 029-B00620 M6X20 SKT BH PAS 12

***205 050-F00400 M4 NUT FLG SER PAS 8

***206 068-441616 M4 WSHR 16OD FLT PAS 106

***207 068-652016 M6 WSHR 20OD FLT PAS 12

***208

***301 MSR-60107UK WH DIRECT LINK A 2

***302 MSR-60108UK WH DIRECT LINK B 1

59

PARTS LIST

13

4 ASSY BLOCK LIGHTING (DSD-5021UK) (D-1/1)

1

101201202

203

ITEM PART NO DESCRIPTION QTY

***1 DSD-5022UK MOUNT MARQUEE CAN LED 1

***101 838-0028UK LED RGB 8X3W CAN 1

***201 000-P00308 M3X8 MSCR PAN PAS 6

***202 068-330808-PN M3 WSHR 8OD FLT NYLON 6

***203 280-A01013-PM ROUTER TWIST D10 SO12.7 PANEL MNT 8

60

PARTS LIST

13

5 ASSY MARQUEE ELEC BOARD LH (MSR-5400UK)

ITEM PART NO DESCRIPTION QTY

****1 MSR-5401UK BOARD MARQUEE ELEC 1

****2 DSD-5402UK BRKT PSU MOUNT 2

****3 CFB-4003-01UK EARTH PLATE 1

****4 DSD-5403UK BRKT VIDEO SW LH 1

****5 DSD-5404UK BRKT VIDEO SW RH 1

****101 400-1000-ATX-01 ATX 1KW CORSAIR CP-9020062-UK 1

****102 EP1476 VIDEO SPLITTER 4W HDMI-HDMI 1

****103 280-A01264-WX ROUTER TWIST D12 SO6.4 WOOD X 12

****104 EP1424 LED CONTROLLER 1

****105 838-14551-02UK AC DISTRIBUTION BD 1

****108 838-0017UK TIMER RELAY 1

****201 012-P03512-F N6X1/2" S/TAP FLG PAS 12

****202 008-B00416 M4X16 TMP BH PAS 8

****203 060-S00400 M4 WSHR SPR PAS 8

****204 068-441616 M4 WSHR 16OD FLT PAS 8

****205 012-P00325 N4X1" S/TAP PAN PAS 8

****301 DSD-60231UK WH PI CAMERA CONTROL 1

****302 DSD-60225UK WH PSU LINK 1

****303 MSR-60101UK WH AC DIST 1

****304 MSR-60102UK WH AC PSU 1

****305 MSR-60103UK WH AC TO MONITORS A 1

****306 MSR-60105UK WH AC DIST 1

****307 MSR-60106UK WH LED CONTROLLER OUT 1

****308 MSR-60113UK WH DC LED CONTROLLER 1

****309 600-7012-100UK HDMI-HDMI CABLE 100cm 1

1

2

3

45

101

102

103 104

105

108

201

201 201

201

201

202 202

202

203 203

203

204 204

204

205

61

PARTS LIST

13

6 ASSY AC SWITCH (DSD-5700UK) (D-1/1)

ITEM NO PART NO DESCRIPTION QTY

****1 DSD-5701UK PLATE MAINS IN 1

****101 EP1302 EUROSOCKET FUSED 10A 250VAC 1

****102 514-5078-5000 FUSE 5X20 CERAMIC SB 500mA 2

****103 SW1109 SWITCH ROCKER 250V AC 1

****104 EP1419 FILTER SCHAFFNER 2030-16-06 1

****105 310-5029-D508 HEAT SHRINK SLEEVING 50.8DIA 4

****106 LB1126-5-250 FUSE LABEL 5A 250V 1

****201 050-F00400 M4 NUT FLG SER PAS 4

****301 DSD-60200UK WH AC IN 1

****302 600-9040-44K WH EARTH 400MM M4M4 1

1

101

103

104

105

105102 106

201

62

PARTS LIST

13

7 ASSY MARQUEE UPRIGHT R (MSR-5070UK) (D-1/2)

2

3

4

5

6

7

8

9

1

10

101

102

103

201

201

201

201

201

201

202

203

203

204

204

205

205

205

205

205

205

206

206

63

PARTS LIST

13

ITEM NO PART NO DESCRIPTION QTY

***1 DSD-5021UK ASSY BLOCK LIGHTING 3

***2 MSR-5002UK FRAME MARQUEE UPRIGHT 1

***3 MSR-5003UK CAP MARQUEE FRAME UPRIGHT 1

***4 MSR-5004UK COVER UPRIGHT FOOT 1

***5 MSR-5005UK PANEL UPRIGHT FRONT 2

***6 MSR-5006UK PANEL UPRIGHT SIDE 4

***7 MSR-5009UK COVER MARQUEE UPRIGHT 1

***8 MSR-5036UK PANEL MARQUEE ELEC ACCESS 1

***9 MSR-5061UK PANEL UPRIGHT LIGHTING MOUNT 4

***10 MSR-5034UK PLATE MAINS IN BLANKING 1

***101 601-0004UK-01 LEG ADJ M16X100x70DIA LNUT 4

***102 FN1012 FAN GUARD METAL 120MM (FG-12) 3

***103 260-0012-01UK FAN DC 12V ROHS 1

***201 029-B00416 M4X16 SKT BH PAS 110

***202 008-B00450 M4X50 TMP BH PAS 4

***203 029-B00620 M6X20 SKT BH PAS 12

***204 050-F00400 M4 NUT FLG SER PAS 8

***205 068-441616 M4 WSHR 16OD FLT PAS 102

***206 068-652016 M6 WSHR 20OD FLT PAS 12

***207

***301 MSR-60107UK WH DIRECT LINK A 2

***302 MSR-60108UK WH DIRECT LINK B 1

***303 MSR-60112UK WH LED UPRIGHT RH 1

7 ASSY MARQUEE UPRIGHT R (MSR-5070UK) (D-2/2)

64

PARTS LIST

13

8 ASSY INST KIT MARQUEE (MSR-INST-MARQ-KIT (D1/2)

12

34

5

6

9

10

11 12

13 14

15

19

21

103

201 201

202

202

202 202

202

202

202

202

202

202

202

202

203

203

204

204

205

205

205

205

205

205

205

205

205

205 205

205

206

206

206

206

206 206

206

206

206

206

206

207

207

208

209

65

PARTS LIST

13

ITEM NO PART NO DESCRIPTION QTY

**1 MSR-5010UK ASSY MARQUEE LH PANEL 1

**2 MSR-5015UK ASSY MARQUEE RH PANEL 1

**3 MSR-5020UK ASSY MARQUEE LH UPPER PANEL 1

**4 MSR-5021UK ASSY MARQUEE MID L UPPER PANEL 1

**5 MSR-5022UK ASSY MARQUEE MID R UPPER PANEL 1

**6 MSR-5023UK ASSY MARQUEE RH UPPER PANEL 1

**9 MSR-5100UK ASSY 42 LED DISPLAY 4

**10 MSR-5120UK ASSY LED DISPLAY MOUNT 4

**11 MSR-5045XUK BRKT MID WIRE COVER REAR 4

**12 MSR-5046UK BRKT MID WIRE COVER FRONT 4

**13 MSR-5047XUK BRKT LH WIRE COVER REAR 1

**14 MSR-5048XUK BRKT RH WIRE COVER REAR 1

**15 MSR-5049XUK BRKT OUTER WIRE COVER FRONT 2

**19 MSR-5080UK ASSY CAMERA MOUNT 4

**20 MSR-5058UK MARQUEE LOGO PANEL 1

**21 MSR-5059UK BOARD WIRE COVER Pi 1

**101 LM1227 UK MAINS LEAD 10A WITH PLUG 1

**102 LM1246 EUROLEAD 10A EUROPEAN SOCKET 1

**103 610-1002-01UK RASPBERRY Pi B+ 811-1284 1

**104 280-L00709-OS STANDOFF 7OD 4ID 9L 4

**201 000-P00408 M4X8 MSCR PAN PAS 4

**202 029-B00416 M4X16 SKT BH PAS 109

**203 020-000820-0B M8X20 SKT CAP BLK 40

**204 060-S00800-0B M8 WSHR SPR BLK 40

**205 060-S00400 M4 WSHR SPR PAS 109

**206 068-441616 M4 WSHR 16OD FLT PAS 113

**207 068-852216-0B M8 WSHR 22OD FLT BLK 40

**208 012-P00320 N4X3/4" S/TAP PAN PAS 4

**209 012-P03512-F N6X1/2" S/TAP FLG PAS 2

**301 MSR-60103UK WH AC MONITORS A 1

**302 MSR-60109UK WH LED UPRIGHT LINK A 1

**303 MSR-60110UK WH BILLBOARD LIGHTING A 1

**304 MSR-60111UK WH DC UPRIGHT LINK A 1

**305 MSR-60115UK WH LED UPRIGHT LINK B 1

**306 MSR-60116UK WH DC UPRIGHT LINK B 1

**307 MSR-60117UK WH AC MONITORS B 1

**308 MSR-60118UK WH BILLBOARD LIGHTING B 1

**309 600-7013-500UK CA HDMI DVI 500cm 2

**310 600-7013-1000UK CA HDMI DVI 1000cm 2

**312 600-7015-2000UK USB EXTN A-A 200CM 2

**313 600-7012-500UK HDMI TO HDMI 500CM 1

8 ASSY INST KIT MARQUEE (MSR-INST-MARQ-KIT (D2/2)

66

PARTS LIST

13

9 ASSY MARQUEE LH PANEL (D-1/1)

ITEM NO PART NO DESCRIPTION QTY

***1 MSR-5011UK PANEL MARQUEE LH 1

***2 MSR-5012UK BRKT MARQUEE LH PANEL FRONT 1

***3 MSR-5013UK BRKT MARQUEE LH PANEL REAR 1

***201 000-P00408 M4X8 MSCR PAN PAS 8

***202 068-441616 M4 WSHR 16OD FLT PAS 8

1

23

201 202

67

PARTS LIST

13

10 ASSY MARQUEE RH PANEL (MSR-5015UK) (D-1/1)

1

32

201202

ITEM NO PART NO DESCRIPTION QTY

**1 MSR-5016UK PANEL MARQUEE RH 1

**2 MSR-5017UK BRKT MARQUEE RH PANEL FRONT 1

**3 MSR-5018UK BRKT MARQUEE RH PANEL REAR 1

**201 000-P00408 M4X8 MSCR PAN PAS 8

**202 068-441616 M4 WSHR 16OD FLT PAS 8

68

PARTS LIST

13

11 ASSY MARQUEE LH UPPER PANEL (MSR-5020UK) (D1/1)

ITEM NO PART NO DESCRIPTION QTY

**1 MSR-5026UK PANEL MARQUEE UPPER LH 1

**2 MSR-5024UK BRKT MARQUEE UPPER PANEL FRONT 1

**3 MSR-5025UK BRKT MARQUEE UPPER PANEL REAR 1

***201 000-P00408 M4X8 MSCR PAN PAS 4

***202 068-441616 M4 WSHR 16OD FLT PAS 4

1

2

3

201 202

69

PARTS LIST

13

12 ASSY MARQUEE MID L UPPER PANEL (MSR-5021UK) (D-1/1)

1

2

3

201 202

ITEM NO PART NO DESCRIPTION QTY

**1 MSR-5027UK PANEL MARQUEE UPPER MID L 1

**2 MSR-5024UK BRKT MARQUEE UPPER PANEL FRONT 1

**3 MSR-5025UK BRKT MARQUEE UPPER PANEL REAR 1

***201 000-P00408 M4X8 MSCR PAN PAS 4

***202 068-441616 M4 WSHR 16OD FLT PAS 4

70

PARTS LIST

13

13 ASSY MARQUEE MID R UPPER PANEL (MSR-5022UK) (D-1/1)

1

2

3

201 202

ITEM NO PART NO DESCRIPTION QTY

**1 MSR-5028UK PANEL MARQUEE UPPER MID R 1

**2 MSR-5024UK BRKT MARQUEE UPPER PANEL FRONT 1

**3 MSR-5025UK BRKT MARQUEE UPPER PANEL REAR 1

***201 000-P00408 M4X8 MSCR PAN PAS 4

***202 068-441616 M4 WSHR 16OD FLT PAS 4

71

PARTS LIST

13

14 ASSY MARQUEE RH UPPER PANEL (MSR-5023UK) (D-1/1)

1

2

3

201 202

ITEM NO PART NO DESCRIPTION QTY

**1 MSR-5029UK PANEL MARQUEE UPPER RH 1

**2 MSR-5024UK BRKT MARQUEE UPPER PANEL FRONT 1

**3 MSR-5025UK BRKT MARQUEE UPPER PANEL REAR 1

***201 000-P00408 M4X8 MSCR PAN PAS 4

***202 068-441616 M4 WSHR 16OD FLT PAS 4

72

PARTS LIST

13

15 ASSY 42 LED DISPLAY (MSR-5100UK) (D-1/2)

1

2

3

4

5

67

810

12

102

107

104

106

201

202

203

204

204

204

101

205

206

207

207

207 209

209

209

209

210

210

210

211

211

73

PARTS LIST

13

ITEM NO PART NO DESCRIPTION QTY

**1 MSR-5101UK ENCLOSURE 42 LED 1

**2 DSD-5102UK BRKT LED MOUNT 2

**3 MSR-5103UK COVER BACK 1

**4 MSR-5104UK BRKT UPPER PANEL LIGHTING 1

**5 MSR-5105UK BRKT LIGHTING STRIP 1

**6 DSD-5106UK PERSPEX LED SCREEN PROTECT 1

**7 MSR-5107UK BRKT LED ASSY LOCATING 1

**8 DSD-5108UK PNL PRISMA BD DMODUL MOUNT 1

**10 DSD-5109UK BRKT LED FILTER 1

**11 MSR-5111UK PLATE OSD COVER 1

**12 MSR-5112UK COVER LIGHTING STRIP 1

**101 200-6042-02-AUO DISPLAY 42" LED AUO P420HVN02.0 1

**102 400-160-51224 PSU 42" LED DPS-160AP-2A-PD01 1

**103 440-DS0010UK STICKER DANGER HIGH VOLTAGE 1

**104 280-A01264-WX ROUTER TWIST D12 SO6.4 WOOD X 12

**105 OS1230 FOAM STRIP 2MM X 10MM 2.3m

**106 280-L00709-OS STANDOFF 7OD 4ID 9L 8

**107 EP1419 FILTER SCHAFFNER 2030-16-06 1

**201 000-P00308 M3X8 MSCR PAN PAS 6

**202 000-P00408 M4X8 MSCR PAN PAS 2

**203 012-P00320 N4X3/4" S/TAP PAN PAS 8

**204 029-B00620 M6X20 SKT BH PAS 10

**205 050-F00400 M4 NUT FLG SER PAS 6

**206 060-S00400 M4 WSHR SPR PAS 6

**207 060-S00600 M6 WSHR SPR PAS 10

**208 068-330808-PN M3 WSHR 8OD FLT NYLON 2

**209 068-441616 M4 WSHR 16OD FLT PAS 16

**210 068-652016 M6 WSHR 20OD FLT PAS 10

**211 008-B00412 M4X12 TMP BH PAS 10

**301 MSR-6003UK WH ASSY MARQUEE BILLBOARD 1

**302 MSR-60104UK WH AC MONITOR 1

15 ASSY 42 LED DISPLAY (MSR-5100UK) (D-2/2)

74

PARTS LIST

13

16 ASSY LED DISPLAY MOUNT (MSR-5120UK) (D-1/1)

ITEM NO PART NO DESCRIPTION QTY

**1 MSR-5121UK MOUNT LED ASSY CABI 1

**2 MSR-5122UK BRKT LED ASSY SUPPORT 2

**201 020-000820 M8X20 SKT CAP PAS 4

**202 060-S00800 M8 WSHR SPR PAS 4

**203 068-852216 M8 WSHR 22OD FLT PAS 4

1

2

201

202

203

75

PARTS LIST

13

ITEM NO PART NO DESCRIPTION QTY

**1 MSR-5081UK BRKT CAMERA LOCATING FRONT 1

**3 MSR-5083UK PLATE CAMERA LOCATING REAR 1

**4 MSR-5084UK PLATE PIN COVER 2

**5 MSR-5085UK BRKT CAMERA MOUNT 1

**101 EP1455 WEBCAM BLK 16429 TRUST 1

**201 029-B00412 M4X12 SKT BH PAS 2

**202 050-F00400 M4 NUT FLG SER PAS 6

**203 068-441616 M4 WSHR 16OD FLT PAS 2

17 ASSY CAMERA MOUNT (MSR-5080UK) (D-1/1)

5

3

41

101

201

202

203

76

PARTS & SERVICE CONTACT INFORMATION

14

14 PARTS & SERVICE CONTACT INFORMATION

- SEGA TOTAL SOLUTIONS -

- PLAY IT AMUSEMENTS -

42 Barwell Business Park

Leatherhead Road,

Chessington,

Surrey,

KT9 2NY

United Kingdom

252 Beinoris Drive,

Wood Dale,

IL,

60191,

United States of America

Parts/Customer Service : +44 (0) 208 391 8060

Technical Support : +44 (0) 208 391 8072

Parts/Customer Service : +01 (874) 364 9787

Technical Support : +01 (874) 364 7775

WIRE COLOUR CODE TABLE

15

77

The color codes for the wires used in the diagrams in the following chapter are as follows.

A PINK

B SKY BLUE

C BROWN

D PURPLE

E LIGHT GREEN

Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric

characters.

1 RED

2 BLUE

3 YELLOW

4 GREEN

5 WHITE

7 ORANGE

8 BLACK

9 GRAY

If the right-hand side numeral of the code is 0, then the wire will be of a single color shown by the left-

hand side numeral (see the above).

Note 1: If the right-hand side numeral is not 0, that particular wire has a spiral color code. The left-

hand side character shows the base color and the right-hand side one, the spiral color.

<Example> 51………WHITE/RED

RED WHITE

Note 2: The character following the wire color code indicates the size of the wire.

U : AWG16

K : AWG18

L : AWG20

None : AWG22

The DC power wire color for this product is di󰮏erent from previous SEGA titles. Working

from the previous wire colors will create a high risk of re.

15 WIRE COLOUR CODE TABLE

78

WIRING DIAGRAMS

16

（D-1/2）

EP1302

IEC INLET

T

514-5078-5000

(N)

(E)

(L)

SW1109

SWITCH

1

2

3

4

5

6

7

8

4

6

5

1

2

8

7

3

4

6

5

1

2

8

7

3

4

6

5

1

2

8

7

3

4

6

5

1

2

8

7

3

4

6

5

1

2

8

7

3

3

2

4

6

5

1

2

1

5

6

3

4

2

1

5

6

3

4

2

1

5

6

3

4

2

1

5

6

3

4

2

1

5

6

3

4

MOULDED IEC

MAINS SOCKET

MINI FIT Jr.

MO LEX

MINI FIT Jr.

MO LEX

MINI FIT Jr.

MO LEX

MINI FIT Jr.

MO LEX

MINI FIT Jr.

MO LEX

MINI FIT Jr.

MO LEX

MINI FIT Jr.

MO LEX

MINI FIT Jr.

MO LEX

MINI FIT Jr.

MO LEX

MINI FIT Jr.

MO LEX

MINI FIT Jr.

MO LEX

MINI FIT Jr.

MO LEX

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

EP1419

NOISE FILTER

2030-16-06

(N)

(L)

(N)

(L)

(E)

838-14551-02UK

AC DISTRIBUTION BOARD

VLR-0 4V VLR-03V

VLR-1 2V

1

2

3

1

2

3

4

1

2

3

4

5

6

7

8

9

10

11

12

(L)

(N)

CFB-4003-01UK

EARTH PLATE

1

40

39

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

USB A

USB A

USB A

USB A

HDMI

HDMI HDMIHDMIHDMIHDMI

1

2

3

4

5

5

4

3

2

1

5

4

3

2

1

5

1

2

3

4

1

2

3

4

12

EP1424

LED CONTROLLER

16 WIRING DIAGRAMS

79

WIRING DIAGRAMS

16

（D-2/2）

42

J8

3

4

2

1 65

J9

73

J4

4

2 3

5

JS T XH

1

1

JST VH

JS T XH

31

32

JS T XH

JST VH

JS T XH

3

64

4

J7

4

J3

J10

1

52

2

7

1 5

JS T XH

3

5 71

J11

42

2

1

3

4

4

J2

3

6

1

JS T XH

5

2

JST VH

J13

1

2

41

2

4

2

J1

3

JST VH

3

3

45

JS T XH

JS T XH

J5

J6

5

7

1

6 42

J8

3

4

2

1 65

J9

73

J4

4

2 3

5

JS T XH

1

1

JST VH

JS T XH

31

32

JS T XH

JST VH

JS T XH

3

64

4

J7

4

J3

J10

1

52

2

7

1 5

JS T XH

3

5 71

J11

42

2

1

3

4

4

J2

3

6

1

JS T XH

5

2

JST VH

J13

1

2

41

2

4

2

J1

3

JST VH

3

3

45

JS T XH

JS T XH

J5

J6

5

7

1

6 42

J8

3

4

2

1 65

J9

73

J4

4

2 3

5

JS T XH

1

1

JST VH

JS T XH

31

32

JS T XH

JST VH

JS T XH

3

64

4

J7

4

J3

J10

1

52

2

7

1 5

JS T XH

3

5 71

J11

42

2

1

3

4

4

J2

3

6

1

JS T XH

5

2

JST VH

J13

1

2

41

2

4

2

J1

3

JST VH

3

3

45

JS T XH

JS T XH

J5

J6

5

7

1

6

42

J8

3

4

2

1 65

J9

73

J4

4

2 3

5

JS T XH

1

1

JST VH

JS T XH

31

32

JS T XH

JST VH

JS T XH

3

64

4

J7

4

J3

J10

1

52

2

7

1 5

JS T XH

3

5 71

J11

42

2

1

3

4

4

J2

3

6

1

JS T XH

5

2

JST VH

J13

1

2

41

2

4

2

J1

3

JST VH

3

3

45

JS T XH

JS T XH

J5

J6

5

7

1

642

J8

3

4

2

1 65

J9

73

J4

4

2 3

5

JS T XH

1

1

JST VH

JS T XH

31

32

JS T XH

JST VH

JS T XH

3

64

4

J7

4

J3

J10

1

52

2

7

1 5

JS T XH

3

5 71

J11

42

2

1

3

4

4

J2

3

6

1

JS T XH

5

2

JST VH

J13

1

2

41

2

4

2

J1

3

JST VH

3

3

45

JS T XH

JS T XH

J5

J6

5

7

1

642

J8

3

4

2

1 65

J9

73

J4

4

2 3

5

JS T XH

1

1

JST VH

JS T XH

31

32

JS T XH

JST VH

JS T XH

3

64

4

J7

4

J3

J10

1

52

2

7

1 5

JS T XH

3

5 71

J11

42

2

1

3

4

4

J2

3

6

1

JS T XH

5

2

JST VH

J13

1

2

41

2

4

2

J1

3

JST VH

3

3

45

JS T XH

JS T XH

J5

J6

5

7

1

6

+

-

+

-